xt-4700 series user guide v1.1
TRANSCRIPT
-
XT-4700 Series User Guide
V1.0 Xirgo Technologies
188 Camino Ruiz, 2nd
Floor Camarillo, CA 93012
-
Contents 1. Hardware Specification ...................................................................................................................................... 2
2. Feature Matrix .................................................................................................................................................. 3
3. SIM Installation ................................................................................................................................................. 4
4. Cable Harness ................................................................................................................................................... 7
4.1 Connector Pin-Out and Description ............................................................................................................... 7
4.2 Cable Description ......................................................................................................................................... 7
5. LED Definition ................................................................................................................................................... 8
6. Device Mounting Options .................................................................................................................................. 9
7. SMS Communication ......................................................................................................................................... 9
8. Firmware Update OTA ..................................................................................................................................... 10
-
1. Hardware Specification
Technology 2G GSM/GPRS/EDGE 3G UMTS/HSPA CDMA 1xRTT Model XT-4700 XT-4760 XT-4750C
Frequency 850/900/1800/1900 800/850/1900/1700/1900 800 Cell Band MHz /2100 MHz band/1900 PCS
band MHz GPS specification Receiver 50 50 channels 50 channels 50 channels channels Receiver -161 dBm -161 dBm -161 dBm tracking Sensitivity Accuracy +/- 2.5m CEP +/- 2.5m CEP +/- 2.5m CEP Cold Start
-
2. Feature Matrix
Technology
2G
3G
CDMA
Feature Highlight XT-4700 XT-4760 XT-4750C
Locate X X X
Idle X X X
Vehicle Disable X X X
Ignition On/Off X X X
Mileage X X X
Periodic Reporting X X X
Speed X X X
Direction Change X X X
Battery Voltage X X X
Battery Disconnect X X X
Tow Alerts X X X
Movement Start/Stop X X X
Warning Buzzer O O O
Acceleration/Deceleration X X X
Park Time X X X
Virtual Odometer X X X
Quick Fence X X X
Device Diagnostics X X X
Motion O O O
Accelerometer O O O
Geo-Zones 10 (3 x Rectangular, 7 x 7-sided Polygon)
Back Up Battery 6600 mAh
Memory 8MB
Communication Protocol SMS, UDP, UDP w/ACK, TCP, UDPC
Firmware Download DOTA, FTP
-
3. SIM Installation
1. Flip the device upside down and remove all six screws as displayed below using a Phillips precision
screwdriver by turning counter clockwise.
2. Remove the cover from device by lifting it up and ensuring the gasket is left in device housing. 3. Carefully unplug the battery. Please ensure to hold all three wires when pulling away from the battery
connector.
4. Remove the hexagonal nut by turning counter clockwise.
4
-
5. Place the SIM card into the SIM tray and gently push the SIM card until it is fully seated in the tray. Note: While the SIM card is being pushed in, the PCB will lift up slightly from bottom. Ensure that the SIM card is installed exactly as depicted in this picture. Use the notched corner for placement reference.
6. Reconnect the battery by plugging the battery connector to the PCB connector (Figure 1). Place the
battery back in the housing the same way it was removed. Please make sure the battery is not touching the capacitor (Figure 2).
Figure 1 Battery Figure 2 Proper Battery 7. Ensure the cover is placed in the correct orientation before replacing on the device. The side with high
wall needs to be facing the harness connector side. The cover high wall slides in the middle of the battery pack and the harness PCB.
High wall
Harness connector
5
-
8. Using a Phillip precision screwdriver, tighten all six screws using 4lbf (pound per inch) torque setting in the order displayed below.
9. Place the hex nut on the harness plug and tighten by turning in clockwise direction.
6
-
4. Cable Harness
4.1 Connector Pin-Out and Description
Pin #
Wire Color
Pin Name
Functional Description
Port Characteristic
1 White IN1 Ignition Sense 8v to 24v, Internally pulled low
2 Yellow IN2 Input port 2.4 to 24V, < 0.2 V
Note: Internally pulled high
3 Black Ground Ground
4 Green Out Output Port (Defaulted open circuit)
5 Blue UART-Rx External battery negative terminal 3.3V Logic Interface
Com Port Settings:
Baud rate: 115200 bps; Flow control: None;
8N1
6 Brown UART-Tx 3.3V Logic Interface
Com Port Settings:
Baud rate: 115200 bps; Flow control:
None;8N1
7 Red VBATT Main battery voltage, DC 6-24 V
8 Orange External ADC input (only available on 6-24 V
3G/CDMA) Note: Internally pulled low
4.2 Cable Description
1. Connects to XT-4700 series devices 2. Power, Input/Output and Rx/Tx wires
-
5. LED Definition
LED Description Status
GSM/Cellular (Blue)
Searching for GSM Network Blinking once a second
2G
GSM/Carrier Lock Blinking once every 3 second
GPS (Green)
Searching for satellite Solid
GPS Lock
Blinking
LED Description Status
GSM/Cellular (Blue)
Searching for GSM Network LED OFF
3G
GSM/Carrier Lock
Fast Blinking once every 1 second
GPS (Green)
Searching for satellite Solid
GPS Lock
Blinking
LED Description Status
CDMA/Cellular Searching for CDMA Network LED OFF
CDMA (Blue) CDMA/Cellular Lock Blinking once every 1 second
GPS (Green)
Searching for satellite Solid
GPS Lock Blinking
-
6. Device Mounting Options
XT-4700 series of device comes with three mounting options: screws, double sided tape and magnet. The mounting kit which comes with device includes screws and double sided tape only. The magnet is optional.
Standard Mounting Kit Example Magnet Mount Example
7. SMS Communication
1. Ensure your SIM card is activated with SMS enabled and you have SIM phone number available. If you have
CDMA device ensure data plan includes SMS and you have mobile # available. 2. Place the SIM card into the device. Skip this step if you have CDMA device. 3. Power up the device by connecting device to 12v DC. 4. Ensure device GSM/CDMA LED is blinking based on LED definition. 5. Using your mobile phone or SMS gateway send +XT:1008 command. Example +XT:1008,5555555555 (phone#
or SMS gateway is the # where you want device to reply back too). 6. Successful reply will be $$359134032774006,1008,5555555555## 7. Once you have set SMS to reply to your mobile or gateway, you can now send other commands to device
via SMS per device protocol documentation.
-
8. Firmware Update OTA 1. Prior to doing a firmware update on any Xirgo product you will need a FTP server where you can host firmware files. 2. You will need the following credentials once you setup you FTP server in order to compile a +XT:1004 command:
a. DIR is the subdirectory under which the Firmware files will be stored b. FUSN is the username used for login into the FTP c. FPWD is the password used for login into the FTP d. FIP is an FTP server IP address in the form YYY.YYY.YYY.YYY or a DNS name
3. Once you have the FTP credentials, compile a 1004 command, Example +XT:1004,/,xirgo3,xirgo1,68.237.174.21 4. Per example below send a SMS to device phone# with +XT:1004 command as show in step #3
1004 command sent to device phone#
Successful response back
5. Now the device is ready for Firmware update. The XT-4700 series of device has one main firmware file. 6. Construct +XT:1006,, command to update MAIN FW. Example +XT:1006,1,X001-1111F2
signifies which firmware to update main firmware 1 for Main FW,
field is firmware file name without extension
7. Send constructed command via SMS, example #1. Once the SMS is sent #2 is first reply back from device with indication that device has begun DOTA process. The final response #3 indicates successfully firmware update. This completed process of updating Main firmware on device.
1006 command sent
st update MAIN 1 Firmware on device 1 SMS response indicates
2 that command was
accepted and device will
begin DOTA
nd SMS response indicates
3 2
device MAIN Firmware
was successfully update.
-
Shipping Mode Devices are shipped from the Xirgo manufacturing facility in Ship mode. Federal regulations require that these device be shipped in an off state since the contain lithium ion batteries. The remove device from Ship mode you must attach +12VDC to input 1 (IN1, white) for five seconds. The device will be unresponsive until this occurs.