yic-e magazine
DESCRIPTION
ÂTRANSCRIPT
ADVISORY BOARD MEMBERS
1. Dr. K.S.SRINIVASAN-PRINCIPAL
2. Mr S.MADHU-VICE PRINCIPAL
3. Mr M.NAGARAJU-HOD
EDITORIAL BOARD MEMBERS-STAFF
1. Mrs L.ASHA
2. Mrs B.ASHWINI
3. Mr MAHESHWARAN
EDITORIAL BOARD MEMBERS-STUDENTS
1. M.PREM KUMAR
2. KHALEEL ULLA SHAIKH
3. G.BRAHMANAND REDDY
4. G.SATISH
5. MD.SAJID
6. M.RAKESH KUMAR
7. N.NIVAS KUMAR
8. P.VINOD KUMAR REDDY
9. P.V.N.B ADITYA
S S.NO TOPICS PG.NO.
1) LATEST TRENDS IN AUTOMOBILES 5-13
2) DEVEOPMENTS IN MECHANICAL FIELD 14-19
3) RESEARCH & DEVELOPMENT(R&D) 20-22
4) REVERSE ENGINEERING 23-24
5) NEXT GENERATION 25-27
6) YOU TUBE LINKS 28-29
7) EVENTS 30
8) PHOTOGRAPHY CLUB 31-37
AUDI 4.0 TFSI engine with cylinder on
demand(COD)
The new 4.0 TFSI engine has a powerful V8 with twin turbochargers, is
equipped with “cylinder on demand” technology. When operating at part
load, four of its cylinders are deactivated. This reduces fuel consumption
by an average of 5%. Active noise control system reduces the noise and
vibration created by the engine when it is switched on to 4 cylinder
mode. On the new 4.0 TFSI, cylinders are deactivated if the load on the
engine is low. It take effects depending on engine speed, is between
about 25 and 40 percent of maximum torque, in other words about 120
and 250 Nm. In this operating range the mean effective pressure rises to
eight bar. Coolant temperature must be at least 30°C and third gear or
higher must have been selected. The engine must be running at more
than idle speed, namely between 960 and 3,500 rpm. If these
preconditions are satisfied, the system closes the inlet and exhaust
valves of two cylinders on each bank. The V8 continues to run as a V4
with a regular firing order, but with the mixture in only two cylinders
instead of four being ignited on each revolution of the crankshaft.
Instead of 1 – 5 – 4 – 8 – 6 – 3 – 7 – 2, the firing order is then 1 – 4 – 6 –
7.
1. LATEST TRENDS IN AUTOMOBILES
The valves are closed by the Audi valvelift system (AVS). These system slides by electromagnetically. When the driver accelerates the pedal rapidly the deactivated cylinders come into motion. The process takes place smoothly & quickly in just 300milliseconds.
Emended & Source from:-www.audi-technology-portal.de
AUDI e-diesel and e-ethanol
Audi has developed new CO₂-neutral fuels. The new technology
involves that the Microorganisms utilize solar energy to produce
synthetic ethanol and synthetic diesel from carbon dioxide and water.
The process is relatively simple; fuels are produced from CO₂ and salt
water with the help of solar energy. The fuel is produced in a specially
developed solar converter system.
The fuel is generated when it utilises the co2 from the industries and the
salt water or brackish water. The sun provides the energy to process
that the organisms need to produce the fuel. co2, water & solar energy
set the circulating production process in the motion in which billions of
microorganisms produce fuel. By the separation of water from the fuel
produced the Audi e-diesel or e-ethanol are filled in filling stations and is
used in Audi cars. These fuels does not cause any harm to the
environment.
Emended & Source from:-www.audi-technology-portal.de
Comparison of ford Eco sport ,Honda amaze
& Hyundai elite i20
Elite i20 Amaze Eco sport
Engine type 1.4L CRDI-DIESEL 1.4L IDTEC-DIESEL 1.5L TDCI-DIESEL
Engine power 90ps 100ps 91ps
Torque 136Nm 200Nm 204Nm
No.of cylinders 4 4 4
Transmission Manual Manual Manual
No.of gears 6 5 5
Mileage(kmpl) 21.9 25.8 22.67
Suspension front Mac person strut with coil spring
Mac person strut Independent Macpherson Strut With Coil Spring And Anti-Roll Bar
Suspension rear Couple Torsion Beam Axle with Coil Spring
Torsion Beam Semi-Independent Twist Beam With Twin Gas And Oil-Filled Shock Absorbers
Steering type Rack & Pinion Electric Power Steering
Epas With Pull Drift Compesation Technology
Minimum Turning Radius
4.7M 4.7M 5.3M
Top speed(kmph) 182 175 170
Ground clearance 170mm 165mm 200mm
The Hyundai Elite i20’s fabulous looks, features, decent handling and a
fairly refined engine, makes it the winner of this comparison. So, if you
want a wholesome package the Elite i20 is the one you should bet your
money on.
Emended & Source from:-zigwjeels.com
2015 BMW i8
BMW has designed a plug-in hybrid sports car offering the nimble
performance and outstanding efficiency. The passenger chamber has
made with carbon fibre reinforced plastic (CFRP). The engine is built
with 1.5L petrol engine with twin power turbo technology. The three-
cylinder combustion engine in the BMW i8 develops 170 kW & 231 hp
which drives the rear wheels, while the 96 kW & 131 hp electric motor
draws its energy from a lithium-ion battery, which can be charged from a
conventional domestic power socket, and sends its power to the front
axle. The i8 enables a range of up to 37 kilometres in the EU test cycle
and a top speed of 250 km/h on electric power alone. While using the
both electrical energy and engine energy it boost ups 0-100kmph in just
4.4sec. The BMW i8 is the first BMW production model to be powered by
a three-cylinder petrol engine. The three-cylinder's BMW Twin Power
Turbo technology comprises a high-performance turbocharging system
and direct petrol injection with high-precision injectors positioned
between the valves. BMW Twin Power Turbo technology and low
internal friction improve both fuel efficiency and torque characteristics.
The electric motor develops maximum power of 96 kW/131 hp and instantly produces its maximum torque of 250Nm. The electric motor drives the car to a top speed of 120kmph. The motor derives its energy from the lithium-ion battery which is centrally mounted underneath the floor of the vehicle. The rear wheels of the BMW i8 are driven by the petrol engine via a six-speed automatic transmission, while the front wheels receive their power from the electric motor. The high-end chassis and suspension technology of the BMW i8 is based on a double-wishbone front axle and a five-link rear axle, whose aluminium components have been specially designed and manufactured in order to optimise both their weight and strength & the Electric Power Steering offers easy handling. The BMW i8 is equipped with the following technologies like:-
Dynamic Damper Control:- The electronically controlled dampers endow the vehicle with sharper agility without any loss of ride comfort. The dampers' characteristics change according to the selected driving mode to deliver the desired vehicle dynamics. The DSC (Dynamic Stability Control) system includes the Anti-lock Braking System (ABS), Cornering Brake Control (CBC), Dynamic Brake Control (DBC), Brake Assist, Brake Standby, Brake Drying function, Start-Off Assistant, Fading Compensation, Active Differential Brake (ADB-x), Driving dynamic impellent torque pre-control, E-Traction, as well as the push button-activated Dynamic Traction Control (DTC) mode.
Emended & Source from:-www.netcarshow.com
2. DEVELOPMENTS IN
MECHANICAL FIELD
Non-destructive testing
-Non-destructive testing (NDT) is a wide group of analysis techniques
used in science and industry to evaluate the properties of a material
without causing damage.
Types of NDT:-
• Visual • Ultrasonic • Dye penetrant inspection (DPI) • Shearography and many more techniques.
1. VISUAL INSPECTION:- Basic principle: illuminate the test specimen with light and examine the specimen with the eye by using Magnifying Glass, Magnifying Mirror, and Microscope. 2. ULTRA SONIC TESTING:- Based in the propagation of ultrasonic waves in the object or material tested. It absorbs or deflects the sound Waves, which are then detected as changes in the waves. 3. DYE PENETRANT INSPECTION:- It is also called as also called liquid penetrant inspection (LPI). It is a widely applied and low-cost inspection method used to locate surface-breaking defects in all non-porous materials (metals, plastics, or ceramics). The penetrant may be applied to all non-ferrous materials and ferrous materials. Inspection steps for LPI:- 1. Pre-cleaning 2. Application of penetrant 3. Excess Penetrant Removal 4. Application of Developer 5. Inspection 6. Post Cleaning
1. Section of material with a surface-breaking crack that is not visible to
the naked eye.
2. Penetrant is applied to the surface.
3. Excess penetrant is removed.
4. Developer is applied, rendering the crack visible.
4. SHEAROGRAPHY:- Shearography or speckle pattern shearing
interferometry is a measuring and testing method. It uses coherent
light or coherent sound waves to provide information about the quality of
different materials in non-destructive testing. It is widely used in
aerospace and automotive works. When a surface area is illuminated
with a highly coherent laser light, a stochastical interference pattern is
created. This interference pattern is called a speckle, and is projected on
a rigid camera's CCD chip.
A vacuum shearography hood and data display unit is applied to a
composite structure to check for defects. An indication of a possible
defect appears as the ripple pattern on the bottom right of the data
screen.
Emended & Source from:-wikipedia.com
Cryogenic engine
A Cryogenic technology is a process of involvement of including of
usage of rocket propellants at Cryogenic temperature. It can be
combination of liquid fuels such as:- Liquid –Oxygen (LOX), and liquid
Hydrogen (LH2) as an oxidizer and fuel in the different mixtures of
proportions. The mixture of fuels offers the highest energy efficiency for
the rocket engines that produces very high amount of thrust. Here, the
Oxygen remains liquid only at the temperature below (-183⁰C) and
Hydrogen at below (-253⁰C). This is a type of rocket engine that is
functionally designed to use the oxidizer which must be refrigerated in
the liquid state. Sometimes, the liquid Nitrogen (LN2) is sometimes used
as fuel because the exhaust is also Nitrogen. Nitrogen is a non-pollutant
gas and during exhaust no other harmful gases are produced. Hence its
efficiency is very high than any other Jet engines.
Advanced tools in manufacturing technology
The cutting tools and tool holders are now manufactured with internal
cooling technology so that there will be no need of separate coolant
pipes.
The above figure shows the redesigned BIG Daishowa Hi-Jet Holder.
The Hi-Jet Holder improves hole making by forcing coolant through the
cutting tool coolant holes, allowing operations at faster speeds and
feeds. It also minimizes overheating and work piece distortion. By using
this technology many cutting tools are designed for better performance.
Emended & Source from:-onlineamd.com
Friction stir welding
Friction-stir welding (FSW) is a solid-state joining process. Heat is
generated between the tool and material which leads to a very soft
region near the FSW tool. Then mechanically it intermixes the two
pieces of metal at the place of the joint, and then the softened metal
(due to the elevated temperature) can be joined using mechanical
pressure which is applied by the tool.
ADVANTAGES:-
1. Low environmental impact.
2. Improved safety due to the absence of toxic fumes
DISADVANTAGES:-
1. Large down forces required with heavy-duty clamping necessary to
hold the plates together
2. Exit hole left when tool is withdrawn.
Emended & Source from:-wikipedia.com
3. RESEARCH & DEVELPOMENT
(R&D)
ECO FRIENDLY AUTOMOBILE AIR-CONDITIONING UTILIZATION EXHAUSTS GAS WASTE HEAT OF INTERNAL COMBUSTION ENGINE.
1. Sohail Bux, 2. A.C. Tiwari 1. Research scholar in mechanical engineering department, UIT RGPV Bhopal, India. 2. Professor and Head in mechanical engineering department, UIT RGPV Bhopal, India.
ABSTRACT
This paper present a vapour Absorption air conditioning system is run by exhaust waste heat of internal combustion engine. A four stroke four cylinder five litre diesel engines coupled with hydraulic dynamometer is dedicated for one ton capacity Lithium Bromide –Water or Aqua ammonia –water refrigeration experimental set up is developed in mechanical department of Rajeev Gandhi technical university Bhopal (m.p.). A shell and tube counter flow type heat exchanger is used as a generator of both absorption refrigeration system and a container used as a absorber are divided into two part one part used for LiBr-H2O solution another part for Aqua Ammonia solution used alternatively for experiment. By varying the load on diesel engine and developed characteristic curves. We conclude the performance of absorption refrigeration system is affected by performance of Diesel engine. This system is saved cost, reduces maintenance, weight of existing air-conditioning and used as natural refrigerant. Also reduce ozone depletion potential (ODP) and Global warming Potential (GWP). For more details:-http://www.iaeme.com/Journalcureentissue.asp Source from:-International Journal of Mechanical Engineering and Technology (IJMET), ISSN 0976 – 6340(Print), ISSN 0976 – 6359(Online), Volume 5, Issue 3, March (2014).
SMOOTHNESS RUNNING OF TRAIN ON
UNEVEN TRACKS WITH THE HELP OF AIR
SPRINGS
1. Dr. Jinesh Kumar Jain 2. Dr. M. P. Singh 3. Dr. G.S. Dangayach 4.
Dhananjay Chauhan
1. Associate Prof., Department of Mechanical Engineering, Govt.
Engg. College, Ajmer(India)
2. Associate Prof. Department of Mechanical Engineering, Jagannath
University,Jaipur(India)
3. Prof., Department of Mechanical Engineering, MNIT, Jaipur(India)
4. PG Scholar Department of Mechanical Engineering, Govt. Engg.
College, Ajmer(India)
ABSTRACT
The main purpose of the air spring is to restrict the vibration at a desirable level as per requirements. Higher rail vehicle speeds generally results in increased vibrations in the car body, which has a negative impact on ride comfort. The suspension of the vehicle has to be modified in order to reduce the vibration and journey should be comfortable i.e. Jerk free journey. It is always desirable to keep the vibration level as low as possible by introducing damping. One of the most important techniques used in the present problem for improving damping is utilizing the air spring in place of helical spring, because due to damping the helical spring gets break up and which causes the serious accident. One of the techniques used in the present problem for improving damping is utilizing the air spring in place of helical spring. This paper consists of two different parts: a theoretical analysis of the problem and an experimental work. In railway vehicles, air springs are used for improving comfort for the passengers and for the prediction of the vibrations in the car body. The design concept evolved from this research work in trusses and frames, transporting system and rail coaches where higher damping is required, which can be made safely by utilizing the air spring system. This system is also help full to reduce the maintenance cost in transportationsystem.
For more details:-
http://www.iaeme.com/Journalcureentissue.asp?VType=5&IType=9&JType=IJMET&PageNumber=6 Source from:-International Journal of Mechanical Engineering and Technology (IJMET)
4. Reverse engineering
What Is Reverse Engineering?
Reverse engineering is also called back engineering, is the process of
extracting knowledge or design information from anything man-made
and re-producing it or reproducing anything based on the extracted
information. Reverse engineering is very common in such diverse fields
as software engineering, entertainment, automotive, consumer products,
microchips, chemicals, electronics, and mechanical designs.
For example if a company has come with a product if they lost their
documentation of that particular product then reverse engineering is
used to know how the product has been developed.
Reverse engineering of machines:-
As computer-aided design (CAD) has become more popular, reverse
engineering has become a viable method to create a 3D virtual model of
an existing physical part for use in 3D CAD, CAM, CAE or other
software. The reverse-engineering process involves measuring an object
and then reconstructing it as a 3D model. The physical object can be
measured using 3D scanning technologies like CMMs, laser
scanners, structured light digitizers, or Industrial CT Scanning.
Emended & Source from:-wikipedia.com
5. NEXT GENERATION
Rotary engine in Mazda RX-7 The Japanese car manufacturer is going to unveil the Mazda RX-7 with
the unbelievable rotary engine which produced more power than the
engines present in this era.
The rotary engine has 3 features:-
1. New dimensions – The engine stroke has lengthened by reducing the
width of rotor housing & increasing the trochodial radius & eccentricity,
this accelerates the rapid growth in fire which means faster in
combustion & improved fuel economy. This results the improved thermal
efficiency and increased torque at all engine speeds.
2. Direct injection technology.
3. Aluminium housing which is compact in size and light in weight.
Emended & Source from:-mazda.com
Next Generation of Rocket Engine
Generally any rocket engine burns the irrespective fuels to generate the
thrust. If any other engine has capacity to generate thrust efficiently then
it can be called rocket engine. Currently NASA scientists are working on
“Xenon Ion Engine‟ which accelerates the ions or atomic particles to
extremely high to create thrust more effectively and efficiently by usage
of electrostatic or electromagnetic force.
Various ion thrusters have been designed and they all generally fit under
two categories. The thrusters are categorized as
either electrostatic or electromagnetic. The main difference is how the
ions are accelerated is:-
-Electrostatic ion thrusters use the Coulomb force and are categorized
as accelerating the ions in the direction of the electric field.
-Electromagnetic ion thrusters use the Lorentz force to accelerate the
ions.
Power supplies for ion thrusters are usually solar panels but, at
sufficiently large distances from the Sun, nuclear power is used.
For more details: - http://en.wikipedia.org/wiki/Ion_thruster
Emended & Source from: - wikipedia.com
1.https://www.youtube.com/watch?v=XS8j7krGH2o
The Making of an Audi
2.https://www.youtube.com/watch?v=L8I6231aGLQ
The art of perfection - The new Audi A8 and its creators
3.https://www.youtube.com/watch?v=2mwFyUNV0x4
Bang & Olufsen Advanced Sound System for Audi
4. https://www.youtube.com/watch?v=XC210EqvVqg
Honda 1 6 i DTEC Engine Technology
5. https://www.youtube.com/watch?v=5Nr7ymjCAfQ
Porsche 918 Spyder: Engine Technology
6. https://www.youtube.com/watch?v=4_rTxEJpP_I
New Porsche 911 Turbo [997] Generation 2 Chassis Technology
7. https://www.youtube.com/watch?v=YduLaR0d8RI
Porsche 911 997 Turbo Technology
8. https://www.youtube.com/watch?v=ygYGWkTPh9M
Historical Mechanical inventions in the Arab World
9. https://www.youtube.com/watch?v=mEpPww4AXMI
2014 Mercedes-Benz S-Class - New Technology Information Video
10. https://www.youtube.com/watch?v=b_m8DqTlOLE
Audi's automatic driving for parking
5. YouTube links
11. https://www.youtube.com/watch?v=Pzn2cGfZqcQ
2015 Audi S8 - Matrix LED headlights
12. https://www.youtube.com/watch?v=QQimY-t52EM
Latest technology in AUDI
13. https://www.youtube.com/watch?v=kZ1NOzIbadk
BMW Intelligent Headlight Technology
14. https://www.youtube.com/watch?v=11-SPeOtCuw
Audi Sport Quattro laser light technology
15. https://www.youtube.com/watch?v=btwKj2I0_wE
Bugatti Veyron Engine Mechanism
16. https://www.youtube.com/watch?v=gWOc2q_MGtg
New Range Rover 2014 Sport - Testing, Dynamics, Technologies
17. https://www.youtube.com/watch?v=IlevIj8SoX4
Range Rover Evoque Skate Park Stunt
18. https://www.youtube.com/watch?v=qKJ41kOghH8
Mercedes-Benz 2014 S-Class Presentation HD Film
19. https://www.youtube.com/watch?v=Ssd2H8STRcg
Jaguar Technology
20. https://www.youtube.com/watch?v=K-LntkxwPPI
The Best Interior in the World -INSIDE BENTLEY
21. http://www.youtube.com/watch?v=jlkqnVoQxqY
Volvo e-drive powertrain
22. http://www.youtube.com/watch?v=c19kn3drdFU&feature=youtu.be
Duke Engines
6. EVENTS
1. ADVANCES IN WELDING & SURFACE ENGINEERING
ORGANISED BY INDIAN INSTITUTE OF WELDING
DATE:-17TH OCTOBER 2014
VENUE:-MARIE GOLD HOTEL
ATTENDED-
STAFF MEMBERS:-
1. NAGARAJU-HOD
2. VISHWANATH-ASST.PROF.
STUDENTS OF MECHANICAL 4TH YEAR:-
1. NAVA BHAVAN,
2. PRASHANTH,
3. ARUN.
UPCOMING EVENTS-
1. WORKSHOP ON- INTERNATIONAL ADVANCED RESEARCH
CENTRE FOR POWDER METALLURGY & NEW MATERIALS
(IARC)-HYD.
2. INDUSTRY VISIT TO- DECCAN ENGINEERING-HYD.
7 . PHOTOGRAPHY CLUB
THEME- NATURE
Photography by Pruthvi-4th year
THEME-EDUCATION
Photography by Pruthvi-4th year
THEME-BLACK&WHITE
Photography by Pruthvi-4th year
THEME-WILD LIFE
Photography by Pruthvi-4th year
THEME-WILD LIFE
Photography by Adithya-4th year
THEME–HISTORICAL STRUCTURES
LOCATION-RAMAGIRI KHILLA-KARIMNAGAR DISTRICT
Photography by Pranay-2nd Year