yj125x vino owners manual - yamaha completely before operating this scooter. do not attempt to...
TRANSCRIPT
OWNER’S MANUAL
5YR-F8199-14LIT-11626-21-54
YJ125X
5YR-F8199-14_ch0cv.pmd 2007/05/21, 17:382
1
2
3
4
5
6
7
8
9
EAU10041
5YR-F8199-14_ch0cv.pmd 2007/05/21, 17:383
1
2
3
4
5
6
7
8
9
EAU10050
INTRODUCTIONEAU10090
Congratulations on your purchase of the Yamaha VINO125. This model is the result of Yamaha’s vast experience in theproduction of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship andreliability that have made Yamaha a leader in these fields.
This manual will give you an understanding of the operation, inspection, and basic maintenance of this scooter. If you haveany questions concerning the operation or maintenance of your scooter, please consult a Yamaha dealer.
The design and manufacture of this Yamaha scooter fully comply with the emissions standards for clean air applicable at thedate of manufacture. Yamaha has met these standards without reducing the performance or economy of operation of thescooter. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to therecommended maintenance schedules and operating instructions contained within this manual.
5YR-F8199-14_ch0cv.pmd 2007/05/21, 17:384
1
2
3
4
5
6
7
8
9
EAU10122
IMPORTANT MANUAL INFORMATIONEAU35821
Particularly important information is distinguished in this manual by the following notations:
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Failure to follow WARNING instructions could result in severe injury or death to the scooteroperator, a bystander, or a person inspecting or repairing the scooter.
A CAUTION indicates special precautions that must be taken to avoid damage to the scooter.
A NOTE provides key information to make procedures easier or clearer.
NOTE:● This manual should be considered a permanent part of this scooter and should remain with it even if the scooter is
subsequently sold.● Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most
current product information available at the time of printing, there may be minor discrepancies between your scooterand this manual. If you have any questions concerning this manual, please consult your Yamaha dealer.
EWA12580
wPLEASE READ THIS MANUAL AND THE “YOU AND YOUR MOTORCYCLE: RIDING TIPS” BOOKLET CAREFULLYAND COMPLETELY BEFORE OPERATING THIS SCOOTER. DO NOT ATTEMPT TO OPERATE THIS SCOOTER UNTILYOU HAVE ATTAINED ADEQUATE KNOWLEDGE OF ITS CONTROLS AND OPERATING FEATURES AND UNTILYOU HAVE BEEN TRAINED IN SAFE AND PROPER RIDING TECHNIQUES. REGULAR INSPECTIONS AND CARE-FUL MAINTENANCE, ALONG WITH GOOD RIDING SKILLS, WILL ENSURE THAT YOU SAFELY ENJOY THE CAPA-BILITIES AND THE RELIABILITY OF THIS SCOOTER.
*Product and specifications are subject to change without notice.
w
cC
NOTE:
Q
5YR-F8199-14_ch0cv.pmd 2007/05/21, 17:385
1
2
3
4
5
6
7
8
9
EAU10122
IMPORTANT MANUAL INFORMATION
EAUT2190
VINO125OWNER’S MANUAL
©2007 by Yamaha Motor Corporation, U.S.A.1st edition, July 2007All rights reserved.
Any reprinting or unauthorized usewithout the written permission ofYamaha Motor Corporation, U.S.A.
is expressly prohibited.Printed in Taiwan.
P/N LIT-11626-21-54
AFFIX DEALER
LABEL HERE
5YR-F8199-14_ch0cv.pmd 2007/05/21, 17:386
1
2
3
4
5
6
7
8
9
EAU10210
TABLE OF CONTENTSSAFETY INFORMATION ................... 1-1
Further safe-riding points ............... 1-4Location of important labels ........... 1-6
DESCRIPTION................................... 2-1Left view ......................................... 2-1Right view ....................................... 2-2Controls and instruments ............... 2-3
INSTRUMENT AND CONTROL FUNC-TIONS ................................................ 3-1
Main switch/steering lock ............... 3-1Indicator lights ................................ 3-2Speedometer unit ........................... 3-2Fuel gauge ...................................... 3-2Handlebar switches ........................ 3-3Front brake lever ............................. 3-4Rear brake lever ............................. 3-4Fuel tank cap .................................. 3-4Fuel ................................................. 3-5Catalytic converter .......................... 3-6Kickstarter ....................................... 3-6Seat ................................................ 3-7Helmet holder ................................. 3-7Storage compartment ..................... 3-8Carrier ............................................. 3-9Luggage hook ................................. 3-9Sidestand ...................................... 3-10Ignition circuit cut-off system ........ 3-10
PRE-OPERATION CHECKS ............. 4-1Pre-operation check list .................. 4-2
OPERATION AND IMPORTANT RIDINGPOINTS .............................................. 5-1
Starting a cold engine .................... 5-1Starting off ...................................... 5-2Acceleration and deceleration ........ 5-2Braking ........................................... 5-2Engine break-in .............................. 5-3Parking ........................................... 5-3
PERIODIC MAINTENANCE AND MINORREPAIR .............................................. 6-1
PERIODIC MAINTENANCE ........... 6-1Owner’s tool kit ............................... 6-1Periodic maintenance chart for the
emission control system .............. 6-3General maintenance and lubrication
chart ............................................ 6-4Removing and installing panels ..... 6-8Engine oil and oil strainer ............... 6-9Final transmission oil .................... 6-11Air filter and V-belt case air filter
elements .................................... 6-12Carburetor .................................... 6-14Checking the throttle cable free
play ............................................ 6-14Tires .............................................. 6-15Cast wheels .................................. 6-16
Checking the front brake lever freeplay ............................................ 6-17
Adjusting the rear brake lever freeplay ............................................ 6-17
Checking the front brake pads and rearbrake shoes ............................... 6-18
Checking the brake fluid level ....... 6-19Changing the brake fluid .............. 6-20Checking and lubricating the
cables ........................................ 6-20Checking and lubricating the throttle
grip and cable ............................ 6-20Lubricating the front and rear brake
levers ......................................... 6-21Checking and lubricating the
centerstand and sidestand ........ 6-21Checking the front fork ................. 6-22Checking the steering ................... 6-22Checking the wheel bearings ....... 6-23Battery .......................................... 6-23Replacing the fuse ........................ 6-25Replacing the headlight bulb ........ 6-25Replacing the tail/brake light bulb 6-27Replacing a turn signal light bulb .6-27Troubleshooting ............................ 6-28Troubleshooting chart ................... 6-29
SCOOTER CARE AND STORAGE ... 7-1Care ................................................ 7-1Storage ........................................... 7-3
5YR-F8199-14_ch0cv.pmd 2007/05/21, 17:387
1
2
3
4
5
6
7
8
9
EAU10210
TABLE OF CONTENTSSPECIFICATIONS ............................. 8-1
CONSUMER INFORMATION ............ 9-1Identification numbers .................... 9-1Reporting safety defects ................. 9-3Motorcycle noise regulation ............ 9-4Maintenance record ........................ 9-5YAMAHA MOTOR CORPORATION,
U.S.A. RIVA LIMITEDWARRANTY ................................ 9-7
YAMAHA EXTENDED SERVICE(Y.E.S.) ........................................ 9-9
5YR-F8199-14_ch0cv.pmd 2007/05/21, 17:388
1-1
1
2
3
4
5
6
7
8
9
QQQQQ SAFETY INFORMATIONEAU10261
SCOOTERS ARE SINGLE TRACK VE-HICLES. THEIR SAFE USE AND OP-ERATION ARE DEPENDENT UPONTHE USE OF PROPER RIDING TECH-NIQUES AS WELL AS THE EXPER-TISE OF THE OPERATOR. EVERYOPERATOR SHOULD KNOW THE FOL-LOWING REQUIREMENTS BEFORERIDING THIS SCOOTER.HE OR SHE SHOULD:8 OBTAIN THOROUGH INSTRUC-
TIONS FROM A COMPETENTSOURCE ON ALL ASPECTS OFSCOOTER OPERATION.
8 OBSERVE THE WARNINGS ANDMAINTENANCE REQUIRE-MENTS IN THE OWNER’SMANUAL.
8 OBTAIN QUALIFIED TRAINING INSAFE AND PROPER RIDINGTECHNIQUES.
8 OBTAIN PROFESSIONAL TECH-NICAL SERVICE AS INDICATEDBY THE OWNER’S MANUAL AND/OR WHEN MADE NECESSARYBY MECHANICAL CONDITIONS.
Safe riding8 Always make pre-operation checks.
Careful checks may help preventan accident.
8 This scooter is designed to carrythe operator and passenger.
8 The failure of motorists to detectand recognize scooters in traffic isthe predominating cause of auto-mobile/scooter accidents. Manyaccidents have been caused by anautomobile driver who did not seethe scooter. Making yourself con-spicuous appears to be very effec-tive in reducing the chance of thistype of accident.
Therefore:9 Wear a brightly colored jacket.9 Use extra caution when ap-
proaching and passing throughintersections, since intersec-tions are the most likely placesfor scooter accidents to occur.
9 Ride where other motorists cansee you. Avoid riding in anothermotorist’s blind spot.
8 Many accidents involve inexperi-enced operators. In fact, many op-erators who have been involved inaccidents do not even have a cur-rent driver’s license.9 Make sure that you are quali-
fied and that you only lend yourscooter to other qualifiedoperators.
9 Know your skills and limits.Staying within your limits mayhelp you to avoid an accident.
9 We recommend that youpractice riding your scooterwhere there is no traffic untilyou have become thoroughlyfamiliar with the scooter and allof its controls.
8 Many accidents have been causedby error of the scooter operator. Atypical error made by the operatoris veering wide on a turn due toEXCESSIVE SPEED orundercornering (insufficient leanangle for the speed).9 Always obey the speed limit
and never travel faster thanwarranted by road and trafficconditions.
Safety information<IXE>
QQQQQ SAFETY INFORMATION
5YR-F8199-14_ch1.pmd 2007/05/21, 17:391
1-2
1
2
3
4
5
6
7
8
9
QQQQQ SAFETY INFORMATION9 Always signal before turning or
changing lanes. Make sure thatother motorists can see you.
8 The posture of the operator andpassenger is important for propercontrol.9 The operator should keep both
hands on the handlebar andboth feet on the footboardduring operation to maintaincontrol of the scooter.
9 The passenger should alwayshold onto the operator, the seatstrap or grab bar, if equipped,with both hands and keep bothfeet on the passenger foot-rests.
9 Never carry a passenger unlesshe or she can firmly place bothfeet on the passenger foot-rests.
8 Never ride under the influence ofalcohol or other drugs.
8 This scooter is designed for on-roaduse only. It is not suitable for off-road use.
Protective apparelThe majority of fatalities from scooter
accidents are the result of head injuries.The use of a safety helmet is the singlemost critical factor in the prevention orreduction of head injuries.8 Always wear an approved helmet.8 Wear a face shield or goggles. Wind
in your unprotected eyes could con-tribute to an impairment of visionwhich could delay seeing a hazard.
8 The use of a jacket, substantialshoes, trousers, gloves, etc., iseffective in preventing or reducingabrasions or lacerations.
8 Never wear loose-fitting clothes,otherwise they could catch on thecontrol levers or wheels and causeinjury or an accident.
8 Never touch the engine or exhaustsystem during or after operation.They become very hot and cancause burns. Always wear protec-tive clothing that covers your legs,ankles, and feet.
8 Passengers should also observethe above precautions.
ModificationsModifications made to this scooter notapproved by Yamaha, or the removal of
original equipment, may render thescooter unsafe for use and may causesevere personal injury. Modificationsmay also make your scooter illegal touse.
Loading and accessoriesAdding accessories or cargo to yourscooter can adversely affect stabilityand handling if the weight distribution ofthe scooter is changed. To avoid thepossibility of an accident, use extremecaution when adding cargo or accesso-ries to your scooter. Use extra care whenriding a scooter that has added cargo oraccessories. Here are some generalguidelines to follow if loading cargo oradding accessories to your scooter:
LoadingThe total weight of the operator, passen-ger, accessories and cargo must notexceed the maximum load limit.
Maximum load:144 kg (317 lb)
5YR-F8199-14_ch1.pmd 2007/05/21, 17:392
1-3
1
2
3
4
5
6
7
8
9
QQQQQ SAFETY INFORMATIONWhen loading within this weight limit,keep the following in mind:8 Cargo and accessory weight should
be kept as low and close to thescooter as possible. Make sure todistribute the weight as evenly aspossible on both sides of thescooter to minimize imbalance orinstability.
8 Shifting weights can create a sud-den imbalance. Make sure that ac-cessories and cargo are securelyattached to the scooter before riding.Check accessory mounts andcargo restraints frequently.
8 Never attach any large or heavyitems to the handlebar, front fork,or front fender. Such items can cre-ate unstable handling or a slowsteering response.
AccessoriesGenuine Yamaha accessories havebeen specifically designed for use onthis scooter. Since Yamaha cannot testall other accessories that may be avail-able, you must personally be responsiblefor the proper selection, installation anduse of non-Yamaha accessories. Use
extreme caution when selecting and in-stalling any accessories.Keep the following guidelines in mind,as well as those provided under “Load-ing” when mounting accessories.8 Never install accessories or carry
cargo that would impair the perfor-mance of your scooter. Carefullyinspect the accessory before us-ing it to make sure that it does notin any way reduce ground clear-ance or cornering clearance, limitsuspension travel, steering travelor control operation, or obscurelights or reflectors.9 Accessories fitted to the
handlebar or the front fork areacan create instability due toimproper weight distribution oraerodynamic changes. Ifaccessories are added to thehandlebar or front fork area,they must be as lightweight aspossible and should be kept toa minimum.
9 Bulky or large accessories mayseriously affect the stability ofthe scooter due to aerodynamiceffects. Wind may attempt to
lift the scooter, or the scootermay become unstable in crosswinds. These accessories mayalso cause instability whenpassing or being passed bylarge vehicles.
9 Certain accessories candisplace the operator from hisor her normal riding position.This improper position limitsthe freedom of movement ofthe operator and may limitcontrol ability, therefore, suchaccessories are not recom-mended.
8 Use caution when adding electricalaccessories. If electrical accesso-ries exceed the capacity of thescooter’s electrical system an elec-tric failure could result, which couldcause a dangerous loss of lights orengine power.
Gasoline and exhaust gas8 GASOLINE IS HIGHLY FLAM-
MABLE:9 Always turn the engine off
when refueling.
5YR-F8199-14_ch1.pmd 2007/05/21, 17:393
1-4
1
2
3
4
5
6
7
8
9
QQQQQ SAFETY INFORMATION9 Take care not to spill any
gasoline on the engine orexhaust system when refueling.
9 Never refuel while smoking orin the vicinity of an open flame.
8 Never start the engine or let it runfor any length of time in a closedarea. The exhaust fumes are poi-sonous and may cause loss of con-sciousness and death within ashort time. Always operate yourscooter in an area that has adequateventilation.
8 Always turn the engine off beforeleaving the scooter unattended andremove the key from the mainswitch. When parking the scooter,note the following:9 The engine and exhaust
system may be hot, therefore,park the scooter in a placewhere pedestrians or childrenare not likely to touch these hotareas.
9 Do not park the scooter on aslope or soft ground, otherwiseit may fall over.
9 Do not park the scooter near aflammable source (e.g., a
kerosene heater, or near anopen flame), otherwise it couldcatch fire.
8 If you should swallow any gasoline,inhale a lot of gasoline vapor, orallow gasoline to get into your eyes,see your doctor immediately. If anygasoline spills on your skin or cloth-ing, immediately wash the affectedarea with soap and water andchange your clothes.
EAU10350
Further safe-riding points8 Make sure to signal clearly when
making turns.8 Braking can be extremely difficult
on a wet road. Avoid hard braking,because the scooter could slide.Apply the brakes slowly when stop-ping on a wet surface.
8 Slow down as you approach a cor-ner or turn. Once you have com-pleted a turn, accelerate slowly.
8 Be careful when passing parkedcars. A driver might not see you andopen a door in your path.
8 Railroad crossings, streetcar rails,iron plates on road constructionsites, and manhole covers becomeextremely slippery when wet. Slowdown and cross them with caution.Keep the scooter upright, otherwiseit could slide out from under you.
8 The brake lining could get wet whenyou wash the scooter. After wash-ing the scooter, check the brakesbefore riding.
8 Always wear a helmet, gloves, trou-sers (tapered around the cuff andankle so they do not flap), and a
Safe-riding points<IXE>
5YR-F8199-14_ch1.pmd 2007/05/21, 17:394
1-5
1
2
3
4
5
6
7
8
9
QQQQQ SAFETY INFORMATIONbright colored jacket.
8 Do not carry too much luggage onthe scooter. An overloaded scooteris unstable. Use a strong cord tosecure any luggage to the carriers.A loose load will affect the stabilityof the scooter and could divert yourattention from the road. (See page1-1.)
5YR-F8199-14_ch1.pmd 2007/05/21, 17:395
1-6
1
2
3
4
5
6
7
8
9
QQQQQ SAFETY INFORMATIONEAU10381
Location of important labelsPlease read the following important labels carefully before operating this vehicle.
Labels, location of<IXE>
1 2 3
4
5
6
5YR-F8199-14_ch1.pmd 2007/05/21, 17:396
1-7
1
2
3
4
5
6
7
8
9
QQQQQ SAFETY INFORMATION
1
2
3
4
5
6
5YR-F8199-14_ch1.pmd 2007/05/21, 17:397
1-8
1
2
3
4
5
6
7
8
9
QQQQQ SAFETY INFORMATION
5YR-F8199-14_ch1.pmd 2007/05/21, 17:398
2-1
1
2
3
4
5
6
7
8
9
DESCRIPTIONEAU10410
Left view
1. Front turn signal light (page 6-27)2. Luggage hook (page 3-9)3. Helmet holder (page 3-7)4. Storage compartment (page 3-8)5. Rear turn signal light (page 6-27)6. Brake lever free play adjusting nut (page 6-17)7. Kickstarter (page 3-6)8. Air filter (page 6-12)9. Battery (page 6-23)
EAU10400
DESCRIPTIONPart locations<IXE>
1
2 3 4
789
5
6
5YR-F8199-14_ch2.pmd 2007/05/21, 17:391
2-2
1
2
3
4
5
6
7
8
9
DESCRIPTIONEAU10420
Right view
1. Tail/brake light (page 6-27)2. Carrier (page 3-9)3. Fuel tank cap (page 3-4)4. Seat (page 3-7)5. Front brake master cylinder (page 6-19)6. Headlight (page 6-25)7. Spark plug (page 6-8)8. Centerstand (page 6-21)9. Muffler
1 2 3
6
789
4 5
5YR-F8199-14_ch2.pmd 2007/05/21, 17:392
2-3
1
2
3
4
5
6
7
8
9
DESCRIPTIONEAU10430
Controls and instruments
1. Rear brake lever (page 3-4)2. Left handlebar switches (page 3-3)3. Speedometer unit (page 3-2)4. Right handlebar switches (page 3-3)5. Front brake lever (page 3-4)6. Throttle grip (page 6-14)7. Main switch/steering lock (page 3-1)8. Fuel gauge (page 3-2)
1 3 4
5
678
2
5YR-F8199-14_ch2.pmd 2007/05/21, 17:393
3-1
1
2
3
4
5
6
7
8
9
INSTRUMENT AND CONTROL FUNCTIONSEAU10444
INSTRUMENT AND CONTROL FUNCTIONSMain switch/steering lock<IXE>
EAU10460
Main switch/steering lock
ZAUM00**
The main switch/steering lock controlsthe ignition and lighting systems, and isused to lock the steering. The variouspositions are described below.
EAU10530
ONAll electrical circuits are supplied withpower, the taillight comes on, and theengine can be started. The key cannotbe removed.
NOTE:The headlight and meter lighting comeon automatically when the engine isstarted.
EAU10680
LOCKThe steering is locked, and all electricalsystems are off. The key can be re-moved.To lock the steering
ZAUM00**
1
1. Push.
1. Turn the handlebars all the way tothe left.
2. Push the key in from the “OFF” po-sition, and then turn it to “LOCK”while still pushing it.
3. Remove the key.
EAU10660
OFFAll electrical systems are off. The keycan be removed.
To unlock the steering
1 2
ZAUM00**
1. Turn.2. Release.
Push the key in, and then turn it to “OFF”while still pushing it.
EWA10060
wNever turn the key to “OFF” or“LOCK” while the vehicle is moving,otherwise the electrical systems willbe switched off, which may result inloss of control or an accident. Makesure that the vehicle is stopped be-fore turning the key to “OFF” or“LOCK”.
5YR-F8199-14_ch3.pmd 2007/05/21, 17:401
3-2
1
2
3
4
5
6
7
8
9
INSTRUMENT AND CONTROL FUNCTIONS
Indicator lights<IXE>
Turn signal indicator light<IXE>
High beam indicator light<IXE>
Speedometer unit<IXE>
Fuel gauge<IXE>
EAU10980
Indicator lights
1 2
010
MPH
20
3040
50
60
70
800
20
40
6080
100
120
ZAUM00**
1. High beam indicator light“&”2. Turn signal indicator lights“4”and 6”
EAU11020
Turn signal indicator light “44444 66666”This indicator light flashes when the turnsignal switch is pushed to the left or right.
EAU11080
High beam indicator light “&&&&&”This indicator light comes on when thehigh beam of the headlight is switchedon.
EAU12150
Fuel gauge
1
ZAUM00**
1. Fuel gauge
The fuel gauge indicates the amount offuel in the fuel tank. The needle movestowards “E” (Empty) as the fuel leveldecreases. When the needle reaches thered line, refuel as soon as possible.
NOTE:Do not allow the fuel tank to empty it-self completely.
EAUT1820
Speedometer unit
1
010
MPH
20
3040
50
60
70
800
20
40
6080
100
120
2
ZAUM00**
1. Speedometer2. Odometer
The speedometer unit is equipped witha speedometer and an odometer. Thespeedometer shows the riding speed.The odometer shows the total distancetraveled.
5YR-F8199-14_ch3.pmd 2007/05/21, 17:402
3-3
1
2
3
4
5
6
7
8
9
INSTRUMENT AND CONTROL FUNCTIONS
Handlebar switches<IXE>
Dimmer switch<IXE>
Turn signal switch<IXE>
Horn switch<IXE>
Engine stop switch<IXE>
Start switch<IXE>
EAU12460
Turn signal switch “44444/66666”To signal a right-hand turn, push thisswitch to “4”. To signal a left-hand turn,push this switch to “6”. When released,the switch returns to the center position.To cancel the turn signal lights, push theswitch in after it has returned to the cen-ter position.
EAU12500
Horn switch “*****”Press this switch to sound the horn.
EAU12660
Engine stop switch “#####/$$$$$”Set this switch to “#” before startingthe engine. Set this switch to “$” to stopthe engine in case of an emergency, suchas when the motorcycle overturns orwhen the throttle cable is stuck.
EAU12700
Start switch “START”Push this switch while applying the frontor rear brake to crank the engine withthe starter.
ECA10050
cCSee page 5-1 for starting instructionsprior to starting the engine.
Right
1
2
ZAUM00**
1. Engine stop switch “#/$“2. Start switch “START”
EAU12400
Dimmer switch “&&&&&/%%%%%”Set this switch to “&” for the high beamand to “%” for the low beam.
EAU12347
Handlebar switchesLeft
12
3
ZAUM00**
1. Dimmer switch “%/&“2. Turn signal switch “4/6”3. Horn switch “*”
5YR-F8199-14_ch3.pmd 2007/05/21, 17:403
3-4
1
2
3
4
5
6
7
8
9
INSTRUMENT AND CONTROL FUNCTIONS
Brake lever, front<IXE>
Brake lever, rear<IXE>
Fuel tank cap<IXE>
EAU12900
Front brake lever
1
ZAUM00**
1. Front brake lever
The front brake lever is located on theright handlebar grip. To apply the frontbrake, pull this lever toward the handle-bar grip.
EAU12950
Rear brake lever
1
ZAUM00**
1. Rear brake lever
The rear brake lever is located on theleft handlebar grip. To apply the rearbrake, pull this lever toward the handle-bar grip.
EAU32483
Fuel tank cap
12
ZAUM00**
1. Fuel tank cap lock cover2. Match marks
To remove the fuel tank cap
Slide the lock cover open, insert the keyinto the lock, and then turn it 1/4 turnclockwise. The lock will be released andthe fuel tank cap can be removed.
To install the fuel tank cap1. Insert the fuel tank cap into the tank
opening with the key inserted in thelock and with the marks on the capand tank aligned.
2. Turn the key counterclockwise tothe original position, remove it, andthen close the lock cover.
5YR-F8199-14_ch3.pmd 2007/05/21, 17:404
3-5
1
2
3
4
5
6
7
8
9
INSTRUMENT AND CONTROL FUNCTIONSFuel<IXE>
EAU36080
Recommended fuel:UNLEADED GASOLINE ONLY
Fuel tank capacity:4.7 L (1.24 US gal) (1.03 Imp.gal)
ECA11400
cCUse only unleaded gasoline. The useof leaded gasoline will cause severedamage to internal engine parts, suchas the valves and piston rings, as wellas to the exhaust system.
Your Yamaha engine has been designedto use regular unleaded gasoline with apump octane number [(R+M)/2] of 86 orhigher, or a research octane number of91 or higher. If knocking (or pinging) oc-curs, use a gasoline of a different brandor premium unleaded fuel. Use of un-leaded fuel will extend spark plug lifeand reduce maintenance costs.
EAU13211
Fuel
1
ZAUM00**
1. Fuel tank filler tube
Make sure that there is sufficient fuel inthe tank. Fill the fuel tank to the bottomof the filler tube as shown.
EWA10880
w88888 Do not overfill the fuel tank, oth-
erwise it may overflow when thefuel warms up and expands.Avoid spilling fuel on the hotengine.
ECA10070
cCImmediately wipe off spilled fuel witha clean, dry, soft cloth, since fuel may
deteriorate painted surfaces or plas-tic parts.
NOTE:The fuel tank cap cannot be installedunless the key is in the lock. In addi-tion, the key cannot be removed if thecap is not properly installed and locked.
EWA10130
wMake sure that the fuel tank cap isproperly installed before riding.
5YR-F8199-14_ch3.pmd 2007/05/21, 17:405
3-6
1
2
3
4
5
6
7
8
9
INSTRUMENT AND CONTROL FUNCTIONS
Catalytic converter<IXE>
Kickstarter<IXE>
EAU13431
Catalytic converterThis model is equipped with a catalyticconverter in the exhaust system.
EWA10860
wThe exhaust system is hot after op-eration. Make sure that the exhaustsystem has cooled down before do-ing any maintenance work.
ECA10700
cCThe following precautions must beobserved to prevent a fire hazard orother damages.88888 Use only unleaded gasoline. The
use of leaded gasoline will causeunrepairable damage to the cata-lytic converter.
88888 Never park the vehicle near pos-sible fire hazards such as grassor other materials that easilyburn.
88888 Do not allow the engine to idletoo long.
EAU13680
Kickstarter
1ZAUM00**
1. Kickstarter
To start the engine, fold out the kickstarterlever, move it down lightly with your footuntil the gears engage, and then push itdown smoothly but forcefully.
GasoholThere are two types of gasohol: gaso-hol containing ethanol and that contain-ing methanol. Gasohol containing etha-nol can be used if the ethanol contentdoes not exceed 10%. Gasohol contain-ing methanol is not recommended byYamaha because it can cause damageto the fuel system or vehicle perfor-mance problems.
5YR-F8199-14_ch3.pmd 2007/05/21, 17:406
3-7
1
2
3
4
5
6
7
8
9
INSTRUMENT AND CONTROL FUNCTIONS
Seat<IXE>
Helmet holder<IXE>
EAU14300
Helmet holder
1
ZAUM00**
1. Helmet holder
The helmet holder is located under theseat.To secure a helmet to the helmetholder
1. Open the seat. (See page 3-7.)2. Attach the helmet to the helmet
holder, and then securely close theseat.
EWA10160
wNever ride with a helmet attached tothe helmet holder, since the helmetmay hit objects, causing loss of con-trol and possibly an accident.
EAU13932
Seat
To open the seat1. Place the scooter on the
centerstand.2. Insert the key into the main switch,
and then turn it counterclockwiseto “OPEN”.
ZAUM00**
NOTE:Do not push inward when turning the key.
3. Fold the seat up.
To close the seat1. Fold the seat down, and then push
it down to lock it in place.
2. Remove the key from the mainswitch if the scooter will be left un-attended.
NOTE:Make sure that the seat is properly se-cured before riding.
5YR-F8199-14_ch3.pmd 2007/05/21, 17:407
3-8
1
2
3
4
5
6
7
8
9
INSTRUMENT AND CONTROL FUNCTIONSTo release the helmet from the hel-met holderOpen the seat, remove the helmet fromthe helmet holder, and then close theseat.
EAU14510
Storage compartment
1
ZAUM00**
1. Storage compartment
There is a storage compartment underthe seat. (See page 3-7.)
EWA10960
w88888 Do not exceed the load limit of 5
kg (11 lb) for the storage com-partment.
88888 Do not exceed the maximumload of 144 kg (317 lb) for the ve-hicle.
ECA10080
cCKeep the following points in mind
Storage compartment<IXE>
when using the storage compart-ment.88888 Since the storage compartment
accumulates heat when exposedto the sun, do not store anythingsusceptible to heat inside it.
88888 To avoid humidity from spread-ing through the storage compart-ment, wrap wet articles in a plas-tic bag before storing them in thecompartment.
88888 Since the storage compartmentmay get wet while the scooter isbeing washed, wrap any articlesstored in the compartment in aplastic bag.
88888 Do not keep anything valuable orbreakable in the storage com-partment.
To store a helmet in the storage com-partment, place the helmet upside-downwith the front facing forward.
NOTE:8 Some helmets cannot be stored in
the storage compartment becauseof their size or shape.
8 Do not leave your scooter unat-
5YR-F8199-14_ch3.pmd 2007/05/21, 17:408
3-9
1
2
3
4
5
6
7
8
9
INSTRUMENT AND CONTROL FUNCTIONS
Carrier<IXE>
Luggage hook<IXE>
EAU15110
Carrier
1
ZAUM00**
1. Rear carrierEWA10170
w88888 Do not exceed the load limit of 3
kg (7 lb) for the carrier.88888 Do not exceed the maximum
load of 144 kg (317 lb) for the ve-hicle.
EAUT1070
Luggage hook
1
ZAUM00**
1. Luggage hookEWAT1030
w88888 Do not exceed the load limit of 3
kg (7 lb) for the luggage hook.88888 Do not exceed the maximum
load of 144 kg (317 lb) for the ve-hicle.
tended with the seat open.
5YR-F8199-14_ch3.pmd 2007/05/21, 17:409
3-10
1
2
3
4
5
6
7
8
9
INSTRUMENT AND CONTROL FUNCTIONSEAU15301
SidestandThe sidestand is located on the left sideof the frame. Raise the sidestand or lowerit with your foot while holding the motor-cycle upright.
NOTE:The built-in sidestand switch is part ofthe ignition circuit cut-off system, whichcuts the ignition in certain situations.(See further down for an explanation ofthe ignition circuit cut-off system.)
EWA10240
wThe vehicle must not be ridden withthe sidestand down, or if thesidestand cannot be properly movedup (or does not stay up), otherwisethe sidestand could contact theground and distract the operator, re-sulting in a possible loss of control.Yamaha’s ignition circuit cut-off sys-tem has been designed to assist theoperator in fulfilling the responsibil-ity of raising the sidestand beforestarting off. Therefore, check this sys-tem regularly as described below and
Sidestand<IXE>
Ignition circuit cut-off system<IXE>
have a Yamaha dealer repair it if itdoes not function properly.
EAU15372
Ignition circuit cut-off systemThe ignition circuit cut-off system (com-prising the sidestand switch and brakelight switches) has the following func-tions.8 It prevents star ting when the
sidestand is up, but neither brakeis applied.
8 It prevents starting when eitherbrake is applied, but the sidestandis still down.
8 It cuts the running engine when thesidestand is moved down.
Periodically check the operation of theignition circuit cut-off system accordingto the following procedure.
EWA10250
wIf a malfunction is noted, have aYamaha dealer check the system be-fore riding.
5YR-F8199-14_ch3.pmd 2007/05/21, 17:4010
3-11
1
2
3
4
5
6
7
8
9
INSTRUMENT AND CONTROL FUNCTIONS
With the engine turned off:1. Move the sidestand down.2. Make sure that the engine stop switch is turned on.3. Turn the key on.4. Keep the front or rear brake applied.5. Push the start switch.
Does the engine start?
NO YES
With the engine still off:6. Move the sidestand up.7. Keep the front or rear brake applied.8. Push the start switch.
Does the engine start?
YES NO
With the engine still running:9. Move the sidestand down.
Does the engine stall?
YES NO
The system is OK. The scooter can be ridden.
NOTE:This check is most reliable if performed with a warmed-up engine.
The sidestand switch may be defective.The scooter should not be ridden until checked by aYamaha dealer.
The brake switch may be defective.The scooter should not be ridden until checked by aYamaha dealer.
The sidestand switch may be defective.The scooter should not be ridden until checked by aYamaha dealer.
5YR-F8199-14_ch3.pmd 2007/05/21, 17:4011
4-1
1
2
3
4
5
6
7
8
9
PRE-OPERATION CHECKSEAU15580
PRE-OPERATION CHECKSEAU15593
The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly,even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or lossof tire air pressure could have serious consequences. Therefore, it is very important, in addition to a thorough visual inspec-tion, to check the following points before each ride.
NOTE:Pre-operation checks should be made each time the vehicle is used. Such an inspection can be accomplished in a very shorttime; and the added safety it assures is more than worth the time involved.
EWA11150
wIf any item in the Pre-operation check list is not working properly, have it inspected and repaired before operatingthe vehicle.
5YR-F8199-14_ch4.pmd 2007/05/21, 17:401
4-2
1
2
3
4
5
6
7
8
9
PRE-OPERATION CHECKSEAU15605
Pre-operation check list
Pre-operation check list<IXE>
ITEM CHECKS PAGE
Fuel• Check fuel level in fuel tank.• Refuel if necessary.• Check fuel line for leakage.
3-5
Engine oil• Check oil level in engine.• If necessary, add recommended oil to specified level.• Check vehicle for oil leakage.
6-9
Final transmission oil • Check vehicle for oil leakage. 6-11
Front brake
• Check operation.• If soft or spongy, have Yamaha dealer bleed hydraulic system.• Check brake pads for wear.• Replace if necessary.• Check fluid level in reservoir.• If necessary, add recommended brake fluid to specified level.• Check hydraulic system for leakage.
6-18, 6-19
Rear brake
• Check operation.• Lubricate cable if necessary.• Check lever free play.• Adjust if necessary.
6-17~6-18
Throttle grip
• Make sure that operation is smooth.• Check free play.• If necessary, have Yamaha dealer adjust cable free play and lubricate cable and
grip housing.
6-14, 6-20
Wheels and tires
• Check for damage.• Check tire condition and tread depth.• Check air pressure.• Correct if necessary.
6-15, 6-16
Brake levers • Make sure that operation is smooth.• Lubricate lever pivoting points if necessary. 6-21
5YR-F8199-14_ch4.pmd 2007/05/21, 17:402
4-3
1
2
3
4
5
6
7
8
9
PRE-OPERATION CHECKS
Centerstand, sidestand • Make sure that operation is smooth.• Lubricate pivot if necessary. 6-21
Chassis fasteners • Make sure that all nuts, bolts and screws are properly tightened.• Tighten if necessary. -
Instruments, lights, signals and switches
• Check operation. • Correct if necessary. -
Engine stop switch • Check operation. 3-3
Sidestand switch • Check operation of ignition circuit cut-off system.• If system is defective, have Yamaha dealer check vehicle. 3-10
ITEM CHECKS PAGE
5YR-F8199-14_ch4.pmd 2007/05/21, 17:403
5-1
1
2
3
4
5
6
7
8
9
OPERATION AND IMPORTANT RIDING POINTSEAU15941
OPERATION AND IMPORTANT RIDING POINTSEAU15980
EWA10870
w88888 Become thoroughly familiar with
all operating controls and theirfunctions before riding. Consulta Yamaha dealer regarding anycontrol or function that you donot thoroughly understand.
88888 Never start the engine or operateit in a closed area for any lengthof time. Exhaust fumes are poi-sonous, and inhaling them cancause loss of consciousness anddeath within a short time. Alwaysmake sure that there is adequateventilation.
88888 For safety, always start the enginewith the centerstand down.
Starting a cold engine<IXE>
EAU16592
Starting a cold engineECA10250
cCSee page 5-3 for engine break-in in-structions prior to operating the ve-hicle for the first time.
In order for the ignition circuit cut-offsystem to enable starting, the sidestandmust be up.
EWA10290
w88888 Before starting the engine, check
the function of the ignition cir-cuit cut-off system according tothe procedure described on page3-10.
88888 Never ride with the sidestanddown.
1. Turn the key to “ON” and make surethat the engine stop switch is setto “#”.
2. Close the throttle completely.3. Start the engine by pushing the
start switch while applying the frontor rear brake.
NOTE:If the engine does not start, release thestart switch, wait a few seconds, andthen try again. Each starting attemptshould be as short as possible to pre-serve the battery. Do not crank the en-gine more than 10 seconds on any oneattempt. If the engine does not start, trywith the throttle open 1/8 turn.
ECA11130
cCFor maximum engine life, alwayswarm the engine up before startingoff. Never accelerate hard when theengine is cold!
5YR-F8199-14_ch5.pmd 2007/05/21, 17:411
5-2
1
2
3
4
5
6
7
8
9
OPERATION AND IMPORTANT RIDING POINTS
Starting off<IXE>
Acceleration and deceleration<IXE>
Braking<IXE>
EAU16780
Acceleration and deceleration
(a)
(b)0
10
MPH
20
3040
50
60
70
800
20
40
6080
100
120
a
b
ZAUM00**
The speed can be adjusted by openingand closing the throttle. To increase thespeed, turn the throttle grip in direction(a). To reduce the speed, turn the throttlegrip in direction (b).
EAU16770
Starting offNOTE:Before starting off, allow the engine towarm up.
1. While pulling the rear brake leverwith your left hand and holding thecarrier with your right hand, pushthe scooter off the centerstand.
ZAUM00**
2. Sit astride the seat, and then ad-just the rear view mirrors.
3. Switch the turn signal on.4. Check for oncoming traffic, and
then slowly turn the throttle grip (onthe right) in order to take off.
5. Switch the turn signal off.
EAU16792
Braking1. Close the throttle completely.2. Apply both front and rear brakes si-
multaneously while gradually in-creasing the pressure.
EWA10300
w88888 Avoid braking hard or suddenly
(especially when leaning over toone side), otherwise the scootermay skid or overturn.
88888 Railroad crossings, streetcarrails, iron plates on road con-struction sites, and manhole cov-ers become extremely slipperywhen wet. Therefore, slow downwhen approaching such areasand cross them with caution.
88888 Keep in mind that braking on awet road is much more difficult.
88888 Ride slowly down a hill, as brak-ing downhill can be very difficult.
5YR-F8199-14_ch5.pmd 2007/05/21, 17:412
5-3
1
2
3
4
5
6
7
8
9
OPERATION AND IMPORTANT RIDING POINTSEAU16830
Engine break-inThere is never a more important periodin the life of your engine than the periodbetween 0 and 1000 km (600 mi). Forthis reason, you should read the follow-ing material carefully.
Since the engine is brand new, do notput an excessive load on it for the first1000 km (600 mi). The various parts inthe engine wear and polish themselvesto the correct operating clearances. Dur-ing this period, prolonged full-throttleoperation or any condition that mightresult in engine overheating must beavoided.
Engine break-in<IXE>
Parking<IXE>
EAU16990
0~500 km (0~300 mi)Avoid prolonged operation above 1/3throttle.
500~1000 km (300~600 mi)Avoid prolonged operation above 1/2throttle.
ECA11500
cCAfter 1000 km (600 mi) of operation,
EAU17212
ParkingWhen parking, stop the engine, and thenremove the key from the main switch.
EWA10310
w88888 Since the engine and exhaust
system can become very hot,
the engine oil must be changed, andthe oil filter element and the oilstrainer cleaned.
1000 km (600 mi) and beyondThe vehicle can now be operated nor-mally.
ECA10270
cCIf any engine trouble should occurduring the engine break-in period,immediately have a Yamaha dealercheck the vehicle.
5YR-F8199-14_ch5.pmd 2007/05/21, 17:413
5-4
1
2
3
4
5
6
7
8
9
OPERATION AND IMPORTANT RIDING POINTSpark in a place where pedestri-ans or children are not likely totouch them.
88888 Do not park on a slope or on softground, otherwise the vehiclemay overturn.
ECA10380
cCNever park in an area where there arefire hazards such as grass or otherflammable materials.
5YR-F8199-14_ch5.pmd 2007/05/21, 17:414
6-1
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIREAU17224
PERIODIC MAINTENANCE AND MINOR REPAIREAU17231
Safety is an obligation of the owner.Periodic inspection, adjustment and lu-brication will keep your vehicle in thesafest and most efficient condition pos-sible. The most important points of mo-torcycle inspection, adjustment, and lu-brication are explained on the followingpages.Maintenance, replacement, or repairof the emission control devices andsystems may be performed by anyrepair establishment or individual thatis certified (if applicable).
EWA10320
wIf you are not familiar with mainte-nance work, have a Yamaha dealer doit for you.
EAU17301
PERIODIC MAINTENANCEPROPER PERIODIC MAINTENANCEOF YOUR VEHICLE IS IMPORTANT INORDER TO ENJOY LONG, PLEASUR-ABLE SERVICE. ESPECIALLY IMPOR-TANT ARE THE MAINTENANCE SER-VICES RELATED TO EMISSIONS CON-TROL. THESE CONTROLS NOT ONLYFUNCTION TO ENSURE CLEANERAIR, BUT ARE ALSO VITAL TOPROPER ENGINE OPERATION ANDMAXIMUM PERFORMANCE. IN THEFOLLOWING PERIODIC MAINTE-NANCE CHARTS, THE SERVICESRELATED TO EMISSIONS CONTROLARE GROUPED SEPARATELY. THESESERVICES REQUIRE SPECIALIZEDDATA, KNOWLEDGE, AND EQUIP-MENT. YAMAHA DEALERS ARETRAINED AND EQUIPPED TO PER-FORM THESE PARTICULAR SER-VICES.
Maintenance, periodic<IXE>
Tool kit<IXE>
EAU17370
Owner’s tool kit
1
ZAUM00**
1. Owner’s tool kit
The owner’s tool kit is located under theseat. (See page 3-7.)The service information included in thismanual and the tools provided in theowner’s tool kit are intended to assistyou in the performance of preventivemaintenance and minor repairs. How-ever, additional tools such as a torquewrench may be necessary to performcertain maintenance work correctly.
NOTE:If you do not have the tools or experi-ence required for a particular job, havea Yamaha dealer perform it for you.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:581
6-2
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIREWA10340
wModifications not approved byYamaha may cause loss of perfor-mance, excessive emissions, and ren-der the vehicle unsafe for use. Con-sult a Yamaha dealer before attempt-ing any changes.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:582
6-3
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIRMaintenance, emission control system<IXE>
EAU17560
Periodic maintenance chart for the emission control system
* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.
NO. ITEM ROUTINE
INITIAL ODOMETER READING
600 mi(1,000 km)
or1
month
2,000 mi (4,000 km)
or6
months
4,000 mi(7,000 km)
or12
months
6,000 mi (10,000 km)
or18
months
8,000 mi (13,000 km)
or24
months
10,000 mi (16,000 km)
or30
months
1 * Fuel line• Check fuel and vacuum hoses for
cracks or damage.• Replace if necessary.
√ √ √ √ √
2 Spark plug
• Check condition.• Adjust gap and clean.• Replace at 4000 mi (7000 km) or
12 months and thereafter every 4000 mi (6000 km) or 12 months.
√ Replace. √ Replace. √
3 * Valve clearance• Check and adjust valve clearance
when engine is cold.√ √ √ √ √ √
4 *Crankcase breather system
• Check breather hose for cracks or damage.
• Replace if necessary.√ √ √ √ √
5 * Idle speed• Check and adjust engine idle
speed.√ √ √ √ √ √
6 * Exhaust system• Check for leakage.• Tighten if necessary.• Replace gasket(s) if necessary.
√ √ √ √ √
7 * Air induction system• Check the air cut-off valve, reed
valve, and hose for damage.• Replace any damaged parts.
√ √ √ √ √
5YR-F8199-14_ch6.pmd 2007/05/24, 19:583
6-4
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIRMaintenance and lubrication, periodic<IXE>
EAU32125
General maintenance and lubrication chart
NO. ITEM ROUTINE
INITIAL ODOMETER READING
600 mi(1,000 km)
or1
month
2,000 mi(4,000 km)
or6
months
4,000 mi(7,000 km)
or12
months
6,000 mi(10,000 km)
or18
months
8,000 mi(13,000 km)
or24
months
10,000 mi(16,000 km)
or30
months
1 * Air filter element • Replace.
2 V-belt case air filter element • Clean
3 * Front brake• Check operation.• Adjust cable and replace brake
shoes if necessary.
4 * Rear brake• Check operation.• Adjust cable and replace brake
shoes if necessary.
5 * Wheels • Check runout and for damage.• Replace if necessary.
6 * Tires
• Check tread depth and for damage.• Replace if necessary.• Check air pressure.• Correct if necessary.
7 * Wheel bearings• Check bearings for smooth
operation.• Replace if necessary.
8 * Steering bearings
• Check bearing assemblies for looseness.
• Moderately repack with lithium-soap-based grease every 8000 mi (13000 km) or 24 months.
Repack.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:584
6-5
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
9 * Chassis fasteners• Check all chassis fitting and
fasteners.• Correct if necessary.
10 Front brake lever pivot shaft • Apply silicone grease lightly.
11 Rear brake lever pivot shaft
• Apply lithium-soap-based grease (all-purpose grease) lightly.
12 Centerstand and sidestand pivots
• Check operation.• Apply lithium-soap-based grease
(all-purpose grease) lightly.
13 * Sidestand switch • Check operation and replace if necessary.
14 * Front fork• Check operation and for oil
leakage.• Replace if necessary.
15 *Shock absorber assembly
• Check operation and for oil leakage.
• Replace if necessary.
16 Engine oil
• Change (warm engine before draining).
• Check oil level and vehicle for oil leakage.
17 Engine oil filter element • Clean.
18 Engine oil strainer • Clean.
NO. ITEM ROUTINE
INITIAL ODOMETER READING
600 mi(1,000 km)
or1
month
2,000 mi(4,000 km)
or6
months
4,000 mi(7,000 km)
or12
months
6,000 mi(10,000 km)
or18
months
8,000 mi(13,000 km)
or24
months
10,000 mi(16,000 km)
or30
months
5YR-F8199-14_ch6.pmd 2007/05/24, 19:585
6-6
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.
NOTE:From 12000 mi (19000 km) or 36 months, repeat the maintenance intervals starting from 4000 mi (7000 km) or 12 months.
19 Final transmission oil
• Check vehicle for oil leakage.• Change.
20 * V-belt • Replace. Every 1200 mi (18000 km)
21 *Front and rear brake switches • Check operation.
22 *Throttle grip housing and cable
• Check operation and free play.• Adjust the throttle cable free play if
necessary.• Lubricate the throttle grip housing
and cable.
23 *Lights, signals and switches
• Check operation.• Adjust headlight beam.
NO. ITEM ROUTINE
INITIAL ODOMETER READING
600 mi(1,000 km)
or1
month
2,000 mi(4,000 km)
or6
months
4,000 mi(7,000 km)
or12
months
6,000 mi(10,000 km)
or18
months
8,000 mi(13,000 km)
or24
months
10,000 mi(16,000 km)
or30
months
5YR-F8199-14_ch6.pmd 2007/05/24, 19:586
6-7
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIREAU17620
NOTE:8 The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
Hydraulic brake system9 When disassembling the master cylinder or caliper cylinder, always replace the brake fluid. Check the brake fluid
level regularly and fill as required.9 Replace the oil seals on the inner parts of the master cylinder and caliper cylinder every two years.9 Replace the brake hoses every four years or if cracked or damaged.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:587
6-8
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIREAU18771
Removing and installing pan-elsThe panels shown need to be removedto perform some of the maintenancejobs described in this chapter. Refer tothis section each time a panel needs tobe removed and installed.
1
2ZAUM00**
1. Panel A2. Panel B
Panels, removing and installing<IXE>
Spark plug, checking<IXE>
EAUT1660
Panels A and BTo remove one of the panelsRemove the screws, and then pull thepanel off as shown.
1
2
ZAUM00**
1. Panel A2. Screw
1
2
ZAUM00**
1. Panel B2. Screw
To install the panelPlace the panel in the original position,and then install the screws.
EAUT1831
Checking the spark plugThe spark plug is an important enginecomponent, which is easy to check.Since heat and deposits will cause anyspark plug to slowly erode, the sparkplug should be removed and checked inaccordance with the periodic mainte-nance and lubrication chart. In addition,the condition of the spark plug can re-veal the condition of the engine.
To remove the spark plug1. Remove panel A. (See page 6-8.)2. Remove the spark plug cap.
1
ZAUM00**
1. Spark plug cap
3. Remove the spark plug as shown,with the spark plug wrench included
5YR-F8199-14_ch6.pmd 2007/05/24, 19:588
6-9
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIREAUT1180
Engine oil and oil strainerThe engine oil level should be checkedbefore each ride. In addition, the oil mustbe changed and the oil strainer cleanedat the intervals specified in the periodicmaintenance and lubrication chart.
To check the engine oil level1. Place the vehicle on the center
stand.
NOTEMake sure that the vehicle is positionedstraight up when checking the oil level.A slight tilt to the side can result in afalse reading.
2. Start the engine, warm it up for sev-eral minutes, and then turn it off.
3. Wait a few minutes until the oilsettles, and then check the oil levelthrough the check window locatedat the bottom-left side of the crank-case.
NOTE:The engine oil should be between theminimum and maximum level marks.
Engine oil and oil strainer<IXE>
in the owner’s tool kit.
To check the spark plug1. Check that the porcelain insulator
around the center electrode of thespark plug is a medium-to-light tan(the ideal color when the vehicle isridden normally).
NOTE:If the spark plug shows a distinctly dif-ferent color, the engine could be operat-ing improperly. Do not attempt to diag-nose such problems yourself. Instead,have a Yamaha dealer check the vehicle.
2. Check the spark plug for electrodeerosion and excessive carbon orother deposits, and replace it if nec-essary.
Specified spark plug:CR7E (NGK)
To install the spark plug1. Measure the spark plug gap with a
wire thickness gauge and, if nec-essary, adjust the gap to specifi-cation.
Spark plug gap:0.7~0.8 mm (0.028~0.031 in)
2. Clean the surface of the spark pluggasket and its mating surface, andthen wipe off any grime from thespark plug threads.
3. Install the spark plug with the sparkplug wrench, and then tighten it tothe specified torque.
Tightening torque:Spark plug:
13 Nm (1.3 m•kgf, 9.4 ft•lbf)
NOTE:If a torque wrench is not available wheninstalling a spark plug, a good estimateof the correct torque is 1/4<->1/2 turnpast finger tight. However, the spark plugshould be tightened to the specifiedtorque as soon as possible.
4. Install the spark plug cap.5. Install the panel.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:589
6-10
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
ZAUM00**
1. Engine oil level check window2. Maximum level mark3. Minimum level mark
4. If the engine oil is below the mini-mum level mark, add sufficient oilof the recommended type to raiseit to the correct level.
To change the engine oil and cleanthe oil strainer
1. Start the engine, warm it up for sev-eral minutes, and then turn it off.
2. Place an oil pan under the engineto collect the used oil.
3. Remove panel A. (See page 6-8.)4. Remove the engine oil filler cap and
drain bolts to drain the oil from thecrankcase.
1
ZAUM00**
1. Engine oil filler cap
1ZAUM00**
1. Engine oil drain bolt AECA10410
cCWhen removing the engine oil drainbolt, the O-ring, spring, and oilstrainer will fall out. Take care not tolose these parts.
5. Clean the oil strainer with solvent,and then check it for damage andreplace it if necessary.
4 3 2 1
1
ZAUM00**
1. Engine oil drain bolt B2. O-ring3. Compression spring4. Strainer
6. Check the O-ring for damage andreplace it if necessary.
7. Install the oil strainer, spring, O-ringand engine oil drain bolts, and thentighten the drain bolts to the speci-fied torque.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5810
6-11
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
Tightening torque:Engine oil drain bolt A:
23 Nm (2.3 m•kgf, 16.6 ft•lbf)Engine oil drain bolt B:
32 Nm (3.2 m•kgf, 23.1 ft•lbf)
NOTE:Make sure that the O-ring is properlyseated.
8. Add the specified amount of therecommended engine oil, and theninstall and tighten the engine oil fillercap.
Recommended engine oil:See page 8-1.
Oil change quantity:1.00 L (1.06 US qt) (0.88 Imp.qt)
ECA11670
cC88888 Do not use oils with a diesel
specification of “CD” or oils of ahigher quality than specified. Inaddition, do not use oils labeled“ENERGY CONSERVING II” orhigher.
88888 Be sure no foreign material en-ters the crankcase.
9. Start the engine, and then let it idlefor several minutes while checkingit for oil leakage. If oil is leaking,immediately turn the engine off andcheck for the cause.
10. Turn the engine off, and then checkthe oil level and correct it if neces-sary.
11. Install the panel.
Final transmission oil<IXE>
EAU20061
Final transmission oilThe final transmission case must bechecked for oil leakage before each ride.If any leakage is found, have a Yamahadealer check and repair the scooter. Inaddition, the final transmission oil mustbe changed as follows at the intervalsspecified in the periodic maintenanceand lubrication chart.
1. Start the engine, warm up the finaltransmission oil by riding thescooter for several minutes, andthen stop the engine.
2. Place the scooter on thecenterstand.
3. Place an oil pan under the finaltransmission case to collect theused oil.
4. Remove the oil filler cap and drainbolt to drain the oil from the finaltransmission case.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5811
6-12
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIREAUT1301
Air filter and V-belt case air fil-ter elementsThe air filter and V-belt case air filter el-ements should be cleaned at the inter-vals specified in the periodic mainte-nance and lubrication chart. Clean bothfilter elements more frequently if you areriding in unusually wet or dusty areas.
Cleaning the air filter element1. Place the scooter on the
centerstand.2. Remove the air filter case cover by
removing the screw.
1
ZAUM00**
1. Air filter case cover
3. Pull the air filter element out, and
Air filter and V-belt case air filter elements<IXE>
1
ZAUM00**
1. Final transmission oil filler cap
1
ZAUM00**
1. Final transmission oil drain bolt
5. Install the final transmission oildrain bolt, and then tighten it to thespecified torque.
Tightening torque:Final transmission oil drain bolt:
23 Nm (2.3 m•kgf, 16.6 ft•lbf)
6. Add the specified amount of therecommended final transmissionoil, and then install and tighten theoil filler cap.
Recommended final transmissionoil:
See page 8-1.Oil quantity:
0.13 L (0.14 US qt) (0.11 Imp.qt)
EWA11310
w88888 Make sure that no foreign mate-
rial enters the final transmissioncase.
88888 Make sure that no oil gets on thetire or wheel.
7. Check the final transmission casefor oil leakage. If oil is leaking,check for the cause.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5812
6-13
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
then blow the dirt out with com-pressed air as shown.
1ZAUM00**
1. Air filter element
ZAUM00**
4. Check the air filter element for dam-age and replace it if necessary.
5. Insert the air filter element into theair filter case.
ECA10480
cC88888 Make sure that the air filter ele-
ment is properly seated in the airfilter case.
88888 The engine should never be op-erated without the air filter ele-ment installed, otherwise thepiston(s) and/or cylinder(s) maybecome excessively worn.
6. Install the air filter case cover byinstalling the screw.
Cleaning the V-belt case air filter ele-ment
1. Remove the kickstarter lever by re-moving the bolt.
2. Remove the crankcase cover by re-moving the screws.
3. Remove the filter element holder byremoving the screw.
4. Pull the air filter element out, andthen clean it with solvent. Aftercleaning, remove the remainingsolvent by squeezing the element.
EWA10430
wUse only a dedicated parts cleaning
solvent. To avoid the risk of fire orexplosion, do not use gasoline orsolvents with a low flash point.
ECA10520
cCTo avoid damaging the air filter ele-ment, handle it gently and carefully,and do not twist it.
5. Apply oil of the recommended typeto the entire surface of the spongematerial, and then squeeze the ex-cess oil out.
NOTE:The air filter element should be wet butnot dripping.
Recommended oil:Engine oil
6. Insert the element into the air filtercase.
7. Install the filter element holder byinstalling the screw.
8. Install the crankcase cover by in-stalling the screws.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5813
6-14
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR9. Install the kickstarter lever by in-
stalling the bolt, then tightening thebolt to the specified torque.
Tightening torque:Kickstarter bolt:
23 Nm (2.3 m•kgf, 16.6ft•lbf)
EAU21251
CarburetorThe carburetor is an important part ofthe engine and its emission control sys-tem, which requires very sophisticatedadjustment. Therefore, carburetor adjust-ments should be left to Yamaha dealer,who has the necessary professionalknowledge and experience.
Carburetor<IXE>
Throttle cable free play, checking<IXE>
EAU21382
Checking the throttle cablefree playThe throttle cable free play should mea-sure 3.0~5.0 mm (0.12~0.2 in) at thethrottle grip. Periodically check thethrottle cable free play and, if necessary,have a Yamaha dealer adjust it.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5814
6-15
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIRTires<IXE>
EAUT1701
TiresTo maximize the performance, durabil-ity, and safe operation of your scooter,note the following points regarding thespecified tires.
Tire air pressureThe tire air pressure should be checkedand, if necessary, adjusted before eachride.
EWA10500
w88888 The tire air pressure must be
checked and adjusted on coldtires (i.e., when the temperatureof the tires equals the ambienttemperature).
88888 The tire air pressure must beadjusted in accordance with theriding speed and with the totalweight of rider, passenger, cargo,and accessories approved for thismodel.
Tire air pressure (measured on coldtires):
Up to 90 kg (198 lb):Front:
150 kPa (22 psi) (1.50 kgf/cm2)Rear:
200 kPa (29 psi) (2.00 kgf/cm2)90 kg (198 lb) to maximum load:
Front:150 kPa (22 psi) (1.50 kgf/cm2)
Rear:225 kPa (33 psi) (2.25 kgf/cm2)
Maximum load*:144 kg (317 lb)
* Total weight of rider, passenger,cargo and accessories
EWA10510
wProper loading of your vehicle is im-portant for several characteristics ofyour vehicle, such as handling, brak-ing, performance and safety. Do notcarry loosely packed items that canshift. Securely pack your heaviestitems close to the center of the mo-torcycle, and distribute the weightevenly from side to side. Properlyadjust the suspension for your load,and check the condition and pressure
of your tires. NEVER OVERLOADYOUR VEHICLE. Make sure that thetotal weight of the cargo, rider, pas-senger, and accessories (cowling,saddlebags, etc. if approved for thismodel) does not exceed the maxi-mum load of the vehicle. Operationof an overloaded motorcycle couldcause tire damage, an accident, oreven injury.
Tire inspection
1
2
ZAUM0054
1. Tire tread depth2. Tire sidewall
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5815
6-16
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIREAU21960
Cast wheelsTo maximize the performance, durabil-ity, and safe operation of your motor-cycle, note the following points regard-ing the specified wheels.8 The wheel rims should be checked
for cracks, bends or warpage be-fore each ride. If any damage isfound, have a Yamaha dealer re-place the wheel. Do not attempteven the smallest repair to thewheel. A deformed or cracked wheelmust be replaced.
8 The wheel should be balancedwhenever either the tire or wheelhas been changed or replaced. Anunbalanced wheel can result in poorperformance, adverse handlingcharacteristics, and a shortenedtire life.
8 Ride at moderate speeds afterchanging a tire since the tire sur-face must first be “broken in” for itto develop its optimal characteris-tics.
Wheels<IXE>
The tires must be checked before eachride. If a tire tread shows crosswise lines(minimum tread depth), if the tire has anail or glass fragments in it, or if thesidewall is cracked, have a Yamahadealer replace the tire immediately.
Minimum tire tread depth (front andrear):
0.8 mm (0.03 in)
NOTE:The tire tread depth limits may differ fromcountry to country. Always comply withthe local regulations.
Tire informationThis scooter is equipped with castwheels and tubeless tires with valves.
EWA10590
wOperating the scooter with exces-sively worn tires decrease riding sta-bility and can lead to loss of control.Have excessively worn tires replacedby a Yamaha dealer immediately.Brakes, tires, and related wheel partsreplacement should be left to aYamaha Service Technician.
Front tire:Size:
3.50-10 51JManufacturer/model:
CHENG SHIN C-922LRear tire:
Size:3.50-10 51J
Manufacturer/model:CHENG SHIN C-6007
EWA10580
w88888 It is dangerous to ride with a
worn-out tire. When a tire treadbegins to show crosswise lines,have a Yamaha dealer replace thetire immediately.
88888 The replacement of all wheel- andbrake-related parts, including thetires, should be left to a Yamahadealer, who has the necessaryprofessional knowledge and ex-perience.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5816
6-17
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
Front brake lever free play, checking<IXE>
Rear brake lever free play, adjusting<IXE>
EAUT1220
Checking the front brake leverfree play
1
ZAUM0107
1. Front brake lever free play
The brake lever free play should mea-sure 2.0~5.0 mm (0.08~0.20 in) asshown. Periodically check the brake le-ver free play and, if necessary, have aYamaha dealer check the brake system.
EWA10640
wAn incorrect brake lever free play in-dicates a hazardous condition in thebrake system. Do not operate themotorcycle until the brake system hasbeen checked or repaired by aYamaha dealer.
EAU22170
Adjusting the rear brake leverfree play
1
ZAUM0108
1. Rear brake lever free play
The brake lever free play should mea-sure 10.0~20.0 mm (0.39~0.79 in) asshown. Periodically check the brake le-ver free play and, if necessary, adjust itas follows.To increase the brake lever free play,turn the adjusting nut at the brake shoeplate in direction (a). To decrease thebrake lever free play, turn the adjustingnut in direction (b).
(b)(a)
1
ZAUM00**
1. Adjusting nut
EWA10650
wIf proper adjustment cannot be ob-tained as described, have a Yamahadealer make this adjustment.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5817
6-18
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU22410
Front brake pads
21
ZAUM00**
1. Brake pad wear indicator2. Brake disc
Each front brake pad is provided with awear indicator, which allows you tocheck the brake pad wear without hav-ing to disassemble the brake. To checkthe brake pad wear, check the positionof the wear indicator while applying the
EAU22380
Checking the front brake padsand rear brake shoesThe front brake pads and the rear brakeshoes must be checked for wear at theintervals specified in the periodic main-tenance and lubrication chart.
Brake pads and shoes, checking<IXE>
brake. If a brake pad has worn to thepoint that the wear indicator almosttouches the brake disc, have a Yamahadealer replace the brake pads as a set.
EAU22540
Rear brake shoes
1
2ZAUM00**
1. Wear indicator2. Wear limit line
The rear brake is provided with a wearindicator, which allows you to check thebrake shoe wear without having to dis-assemble the brake. To check the brakeshoe wear, check the position of thewear indicator while applying the brake.If a brake shoe has worn to the pointthat the wear indicator reaches the wear
limit line, have a Yamaha dealer replacethe brake shoes as a set.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5818
6-19
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIRBrake fluid level, checking<IXE>
EAU32344
Checking the brake fluid level
LOWER MIN
1
ZAUM00**
1. Minimum level mark
Insufficient brake fluid may allow air toenter the brake system, possibly caus-ing it to become ineffective.
Before riding, check that the brake fluidis above the minimum level mark andreplenish if necessary. A low brake fluidlevel may indicate worn brake pads and/or brake system leakage. If the brakefluid level is low, be sure to check thebrake pads for wear and the brake sys-tem for leakage.
Observe these precautions:8 When checking the fluid level, make
sure that the top of the master cyl-inder is level by turning the handle-bars.
8 Use only the recommended qualitybrake fluid, otherwise the rubberseals may deteriorate, causingleakage and poor braking perfor-mance.
Recommended brake fluid:DOT 4
8 Refill with the same type of brakefluid. Mixing fluids may result in aharmful chemical reaction and leadto poor braking performance.
8 Be careful that water does not en-ter the master cylinder when refill-ing. Water will significantly lower theboiling point of the fluid and mayresult in vapor lock.
8 Brake fluid may deteriorate paintedsurfaces or plastic parts. Alwaysclean up spilled fluid immediately.
8 As the brake pads wear, it is nor-mal for the brake fluid level togradually go down. However, if the
brake fluid level goes down sud-denly, have a Yamaha dealer checkthe cause.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5819
6-20
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIREAU22720
Changing the brake fluidHave a Yamaha dealer change the brakefluid at the intervals specified in theNOTE after the periodic maintenanceand lubrication chart. In addition, havethe oil seals of the brake master cylin-der and caliper as well as the brake hosereplaced at the intervals listed below orwhenever they are damaged or leaking.8 Oil seals: Replace every two years.8 Brake hose: Replace every four
years.
Brake fluid, changing<IXE>
Cables, checking and lubricating<IXE>
Throttle grip and cable, checking and lubricating<IXE>
EAU23111
Checking and lubricating thethrottle grip and cableThe operation of the throttle grip shouldbe checked before each ride. In addi-tion, the cable should be lubricated atthe intervals specified in the periodicmaintenance chart.
EAU23091
Checking and lubricating thecablesThe operation of all control cables andthe condition of the cables should bechecked before each ride, and thecables and cable ends should be lubri-cated if necessary. If a cable is dam-aged or does not move smoothly, havea Yamaha dealer check or replace it.
Recommended lubricant:Yamaha Chain and Cable Lube orengine oil SAE 10W-30
EWA10710
wDamage to the outer housing ofcables may result in internal rustingand cause interference with cablemovement. Replace damaged cablesas soon as possible to prevent un-safe conditions.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5820
6-21
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
Brake levers, lubricating<IXE>
Centerstand and sidestand, checking and lubricating<IXE>
EAU23211
Checking and lubricating thecenterstand and sidestand
ZAUM00**
The operation of the centerstand andsidestand should be checked beforeeach ride, and the pivots and metal-to-metal contact surfaces should be lubri-cated if necessary.
EWA10740
wIf the centerstand or sidestand doesnot move up and down smoothly,have a Yamaha dealer check or repairit.
Recommended lubricant:Lithium-soap-based grease (all-purpose grease)
EAU43640
Lubricating the front and rearbrake levers
ZAUM00**
The pivoting points of the front and rearbrake levers must be lubricated at theintervals specified in the periodic main-tenance and lubrication chart.
Recommended lubricants:Front brake lever:
Silicone greaseRear brake lever:
Lithium-soap-based grease(all-purpose grease)
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5821
6-22
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
Front fork, checking<IXE>
Steering, checking<IXE>
EAU23271
Checking the front forkThe condition and operation of the frontfork must be checked as follows at theintervals specified in the periodic main-tenance and lubrication chart.
To check the conditionEWA10750
wSecurely support the motorcycle sothat there is no danger of it fallingover.
Check the inner tubes for scratches,damage and excessive oil leakage.
To check the operation1. Place the motorcycle on a level sur-
face and hold it in an upright posi-tion.
2. While applying the front brake, pushdown hard on the handlebars sev-eral times to check if the front forkcompresses and reboundssmoothly.
ZAUM00**
ECA10590
cCIf any damage is found or the frontfork does not operate smoothly, havea Yamaha dealer check or repair it.
EAU23280
Checking the steeringWorn or loose steering bearings maycause danger. Therefore, the operationof the steering must be checked as fol-lows at the intervals specified in theperiodic maintenance and lubricationchart.
1. Place a stand under the engine toraise the front wheel off the ground.
EWA10750
wSecurely support the motorcycle sothat there is no danger of it fallingover.
2. Hold the lower ends of the front forklegs and try to move them forwardand backward. If any free play canbe felt, have a Yamaha dealer checkor repair the steering.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5822
6-23
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
Wheel bearings, checking<IXE>
Battery<IXE>
EAU23290
Checking the wheel bearingsThe front and rear wheel bearings mustbe checked at the intervals specified inthe periodic maintenance and lubricationchart. If there is play in the wheel hub orif the wheel does not turn smoothly,have a Yamaha dealer check the wheelbearings.
EAUT1230
Battery
1
ZAUM00**
1. Battery
This model is equipped with a sealed-type (MF) battery, which does not re-quire any maintenance. There is no needto check the electrolyte or to add dis-tilled water.
ECA10620
cCNever attempt to remove the batterycell seals, as this would permanentlydamage the battery.
EWA10760
w88888 Electrolyte is poisonous and dan-
gerous since it contains sulfuric
ZAUM00**
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5823
6-24
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIRacid, which causes severe burns.Avoid any contact with skin, eyesor clothing and always shieldyour eyes when working nearbatteries. In case of contact, ad-minister the following FIRST AID.99999 EXTERNAL: Flush with
plenty of water.99999 INTERNAL: Drink large
quantities of water or milkand immediately call aphysician.
99999 EYES: Flush with water for15 minutes and seek promptmedical attention.
88888 Batteries produce explosive hy-drogen gas. Therefore, keepsparks, flames, cigarettes, etc.,away from the battery and pro-vide sufficient ventilation whencharging it in an enclosed space.
88888 KEEP THIS AND ALL BATTERIESOUT OF THE REACH OF CHIL-DREN.
The battery is located under thefootboard. Remove panel B to accessthe battery. (See page 6-7.)
To charge the batteryHave a Yamaha dealer charge the bat-tery as soon as possible if it seems tohave discharged. Keep in mind that thebattery tends to discharge more quicklyif the vehicle is equipped with optionalelectrical accessories.
To store the battery1. If the vehicle will not be used for
more than one month, remove thebattery, fully charge it, and thenplace it in a cool, dry place.
2. If the battery will be stored for morethan two months, check it at leastonce a month and fully charge it ifnecessary.
3. Fully charge the battery before in-stallation.
4. After installation, make sure thatthe battery leads are properly con-nected to the battery terminals.
ECA10630
cC88888 Always keep the battery charged.
Storing a discharged battery cancause permanent battery dam-age.
88888 To charge a sealed-type (MF) bat-tery, a special (constant-voltage)battery charger is required. Us-ing a conventional batterycharger will damage the battery.If you do not have access to asealed-type (MF) battery charger,have a Yamaha dealer chargeyour battery.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5824
6-25
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIREAUT1240
Replacing the fuse
1
ZAUM00**
1. Fuse
The fuse holder is located beside thebattery. Remove panel B to access thefuse. (See page 6-8.)If the fuse is blown, replace it as fol-lows.
1. Turn the key to “OFF” and turn offall electrical circuits.
2. Remove the blown fuse, and theninstall a new fuse of the specifiedamperage.
Specified fuse:10.0 A
Fuse, replacing<IXE>
Headlight bulb, replacing<IXE>
ECA10640
cCDo not use a fuse of a higher amper-age rating than recommended toavoid causing extensive damage tothe electrical system and possibly afire.
3. Turn the key to “ON” and turn onthe electrical circuits to check if thedevices operate.
4. If the fuse immediately blows again,have a Yamaha dealer check theelectrical system.
EAU23780
Replacing the headlight bulbThis model is equipped with a quartzbulb headlight. If the headlight bulb burnsout, replace it as follows.
1. Remove the headlight unit by re-moving the screws.
1
ZAUM00**
1. Headlight unit
2. Disconnect the headlight coupler,and then remove the bulb cover.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5825
6-26
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
2
1
ZAUM00**
1. Headlight coupler2. Bulb cover
3. Remove the headlight bulb holderby turning it counterclockwise, andthen remove the defective bulb.
1
ZAUM00**
1. Headlight bulb holderEWA10790
wHeadlight bulbs get very hot. There-fore, keep flammable products awayfrom a lit headlight bulb, and do nottouch the bulb until it has cooleddown.
4. Place a new headlight bulb into po-sition, and then secure it with thebulb holder.
ECA10660
cCDo not touch the glass part of theheadlight bulb to keep it free from oil,otherwise the transparency of theglass, the luminosity of the bulb, andthe bulb life will be adversely affected.
Thoroughly clean off any dirt and fin-gerprints on the headlight bulb us-ing a cloth moistened with alcoholor thinner.
5. Install the headlight bulb cover, andthen connect the coupler.
6. Install the headlight unit by install-ing the screws.
7. Have a Yamaha dealer adjust theheadlight beam if necessary.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5826
6-27
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIREAU24131
Replacing the tail/brake lightbulb
12
ZAUM00**
1. Tail/brake light lens2. Bulb
1. Remove the tail/brake light lens byremoving the screws.
2. Remove the defective bulb by push-ing it in and turning it counterclock-wise.
3. Insert a new bulb into the socket,push it in, and then turn it clock-wise until it stops.
4. Install the lens by installing thescrews.
ECA10680
cCDo not overtighten the screws, other-
Tail/brake light bulb, replacing<IXE>
Turn signal light bulb, replacing<IXE>
wise the lens may break. EAU24202
Replacing a turn signal lightbulb
1. Remove the turn signal light lensby removing the screw.
1
2
ZAUM00**
1. Turn signal light lens2. Bulb
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5827
6-28
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIRTroubleshooting<IXE>
EAU25860
TroubleshootingAlthough Yamaha scooters receive athorough inspection before shipmentfrom the factory, trouble may occur dur-ing operation. Any problem in the fuel,compression, or ignition systems, forexample, can cause poor starting andloss of power.The following troubleshooting chart rep-resents a quick and easy procedure forchecking these vital systems yourself.However, should your scooter require anyrepair, take it to a Yamaha dealer, whoseskilled technicians have the necessarytools, experience, and know-how to ser-vice the scooter properly.Use only genuine Yamaha replacementparts. Imitation parts may look likeYamaha parts, but they are often infe-rior, have a shorter service life and canlead to expensive repair bills.
2
1
ZAUM00**
1. Turn signal light lens2. Bulb
2. Remove the defective bulb by push-ing it in and turning it counterclock-wise.
3. Insert a new bulb into the socket,push it in, and then turn it clock-wise until it stops.
4. Install the lens by installing thescrew.
ECA11190
cCDo not overtighten the screw, other-wise the lens may break.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5828
6-29
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIRTroubleshooting chart<IXE>
Check the fuel level inthe fuel tank.
1. FuelThere is enough fuel.
There is no fuel.
Check the compression.
Supply fuel. The engine does not start. Check the compression.
Operate the electric starter.
2. CompressionThere is compression.
There is no compression.
Check the ignition.
Have a Yamaha dealercheck the vehicle.
Remove the spark plugsand check the electrodes.
3. Ignition Wipe off with a dry cloth and correct thespark plug gaps, or replace the spark plugs.
Have a Yamaha dealer check the vehicle.
The engine does not start.Have a Yamaha dealercheck the vehicle.
The engine does not start.Check the battery.
Operate the electric starter.
4. BatteryThe engine turns over quickly.
The engine turns over slowly.
The battery is good.
Check the battery lead connections,and charge the battery if necessary.
Dry
WetOpen the throttle halfway and operatethe electric starter.
EAU25901
Troubleshooting chartEWA10840
wKeep away open flames and do not smoke while checking or working on the fuel system.
5YR-F8199-14_ch6.pmd 2007/05/24, 19:5829
7-1
1
2
3
4
5
6
7
8
9
SCOOTER CARE AND STORAGECare<IXE>
EAU25991
SCOOTER CARE AND STORAGEEAU26091
CareWhile the open design of a scooter re-veals the attractiveness of the technol-ogy, it also makes it more vulnerable.Rust and corrosion can develop even ifhigh-quality components are used. Arusty exhaust pipe may go unnoticedon a car, however, it detracts from theoverall appearance of a scooter. Fre-quent and proper care does not onlycomply with the terms of the warranty,but it will also keep your scooter look-ing good, extend its life and optimize itsperformance.
Before cleaning1. Cover the muffler outlet with a plas-
tic bag after the engine has cooleddown.
2. Make sure that all caps and cov-ers as well as all electrical couplersand connectors, including thespark plug cap, are tightly installed.
3. Remove extremely stubborn dirt,like oil burnt onto the crankcase,with a degreasing agent and abrush, but never apply such prod-ucts onto seals, gaskets and wheel
axles. Always rinse the dirt anddegreaser off with water.
CleaningECA10781
cC●●●●● Avoid using strong acidic wheel
cleaners, especially on spokedwheels. If such products areused on hard-to-remove dirt, donot leave the cleaner on the af-fected area any longer than in-structed. Also, thoroughly rinsethe area off with water, immedi-ately dry it, and then apply a cor-rosion protection spray.
●●●●● Improper cleaning can damageplastic parts such as cowlings,panels, windshields, headlightlenses, meter lenses, etc. Useonly a soft, clean cloth or spongewith mild detergent and water toclean plastic.
●●●●● Do not use any harsh chemicalproducts on plastic parts. Besure to avoid using cloths orsponges which have been incontact with strong or abrasivecleaning products, solvent or
thinner, fuel (gasoline), rust re-movers or inhibitors, brake fluid,antifreeze or electrolyte.
●●●●● Do not use high-pressure wash-ers or steam-jet cleaners sincethey cause water seepage anddeterioration in the followingareas: seals (of wheel andswingarm bearings, fork andbrakes), electric components(couplers, connectors, instru-ments, switches and lights),breather hoses and vents.
●●●●● For scooters equipped with awindshield: Do not use strongcleaners or hard sponges asthey will cause dulling orscratching. Some cleaning com-pounds for plastic may leavescratches on the windshield.Test the product on a small hid-den part of the windshield tomake sure that it does not leaveany marks. If the windshield isscratched, use a quality plasticpolishing compound after wash-ing.
5YR-F8199-14_ch7.pmd 2007/05/21, 17:411
7-2
1
2
3
4
5
6
7
8
9
SCOOTER CARE AND STORAGEAfter normal useRemove dirt with warm water, a milddetergent, and a soft, clean sponge, andthen rinse thoroughly with clean water.Use a toothbrush or bottlebrush forhard-to-reach areas. Stubborn dirt andinsects will come off more easily if thearea is covered with a wet cloth for afew minutes before cleaning.
After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on theroads during winter are extremely cor-rosive in combination with water, carryout the following steps after each ridein the rain, near the sea or on salt-sprayed roads.
NOTE:Salt sprayed on roads in the winter mayremain well into spring.
1. Clean the scooter with cold waterand a mild detergent after the en-gine has cooled down.
ECA10790
cCDo not use warm water since it in-creases the corrosive action of thesalt.
2. Apply a corrosion protection sprayon all metal, including chrome- andnickel-plated, surfaces to preventcorrosion.
After cleaning1. Dry the scooter with a chamois or
an absorbing cloth.2. Use a chrome polish to shine
chrome, aluminum and stainless-steel parts, including the exhaustsystem. (Even the thermally in-duced discoloring of stainless-steelexhaust systems can be removedthrough polishing.)
3. To prevent corrosion, it is recom-mended to apply a corrosion pro-tection spray on all metal, includ-ing chrome- and nickel-plated, sur-faces.
4. Use spray oil as a universal cleanerto remove any remaining dirt.
5. Touch up minor paint damagecaused by stones, etc.
6. Wax all painted surfaces.7. Let the scooter dry completely be-
fore storing or covering it.EWA10940
w●●●●● Make sure that there is no oil or
wax on the brakes or tires. If nec-essary, clean the brake discsand brake linings with a regularbrake disc cleaner or acetone,and wash the tires with warmwater and a mild detergent.
●●●●● Before operating the scootertest its braking performance andcornering behavior.
ECA10800
cC●●●●● Apply spray oil and wax spar-
ingly and make sure to wipe offany excess.
●●●●● Never apply oil or wax to anyrubber and plastic parts, buttreat them with a suitable careproduct.
●●●●● Avoid using abrasive polishingcompounds as they will wear
5YR-F8199-14_ch7.pmd 2007/05/21, 17:412
7-3
1
2
3
4
5
6
7
8
9
SCOOTER CARE AND STORAGEaway the paint.
NOTE:Consult a Yamaha dealer for advice onwhat products to use.
EAU26300
StorageShort-termAlways store your scooter in a cool, dryplace and, if necessary, protect itagainst dust with a porous cover.
ECA10820
cC●●●●● Storing the scooter in a poorly
ventilated room or covering itwith a tarp, while it is still wet,will allow water and humidity toseep in and cause rust.
●●●●● To prevent corrosion, avoiddamp cellars, stables (becauseof the presence of ammonia) andareas where strong chemicalsare stored.
Long-termBefore storing your scooter for severalmonths:
1. Follow all the instructions in the“Care” section of this chapter.
2. Drain the carburetor float chamberby loosening the drain bolt; this willprevent fuel deposits from buildingup. Pour the drained fuel into thefuel tank.
Storage<IXE>
3. Fill up the fuel tank and add fuelstabilizer (if available) to prevent thefuel tank from rusting and the fuelfrom deteriorating.
4. Perform the following steps to pro-tect the cylinder, piston rings, etc.from corrosion.a. Remove the spark plug cap and
spark plug.b. Pour a teaspoonful of engine oil
into the spark plug bore.c. Install the spark plug cap onto
the spark plug, and then placethe spark plug on the cylinderhead so that the electrodes aregrounded. (This will limit spark-ing during the next step.)
d. Turn the engine over severaltimes with the starter. (This willcoat the cylinder wall with oil.)
e. Remove the spark plug cap fromthe spark plug, and then installthe spark plug and the spark plugcap.
EWA10950
wTo prevent damage or injury fromsparking, make sure to ground the
5YR-F8199-14_ch7.pmd 2007/05/21, 17:413
7-4
1
2
3
4
5
6
7
8
9
SCOOTER CARE AND STORAGEspark plug electrodes while turningthe engine over.
5. Lubricate all control cables and thepivoting points of all levers andpedals as well as of the sidestand/centerstand.
6. Check and, if necessary, correctthe tire air pressure, and then liftthe scooter so that both of itswheels are off the ground. Alterna-tively, turn the wheels a little everymonth in order to prevent the tiresfrom becoming degraded in onespot.
7. Cover the muffler outlet with a plas-tic bag to prevent moisture from en-tering it.
8. Remove the battery and fullycharge it. Store it in a cool, dryplace and charge it once a month.Do not store the battery in an ex-cessively cold or warm place [lessthan 0 °C (30 °F) or more than 30°C (90 °F)]. For more informationon storing the battery, see page 6-21.
NOTE:Make any necessary repairs beforestoring the scooter.
5YR-F8199-14_ch7.pmd 2007/05/21, 17:414
8-1
1
2
3
4
5
6
7
8
9
SPECIFICATIONSEAU26320
SPECIFICATIONSSpecifications<IXE>
EAU2633K
DimensionsOverall length
1755 mm (69.1 in)Overall width
699 mm (27.5 in)Overall height
1063 mm (41.9 in)Seat height
759 mm (29.9 in)Wheelbase
1230 mm (48.4 in)Ground clearance
95 mm (3.74 in)Minimum turning radius
1800 mm (70.9 in)Weight
With oil and fuel109.0 kg (240 lb)
EngineEngine type
Air cooled 4-stroke, SOHCCylinder arrangement
Forward-inclined single cylinderDisplacement
125.0 cm3
Bore x stroke51.5 x 60.0 mm (2.03 x 2.36 in)
Compression ratio9.80 :1
Starting systemElectric starter and kickstarter
Lubrication systemWet sump
Engine oilType
YAMALUBE 4, SAE10W30 or SAE20W40
10 30 50 70 90 1100 130 ˚F
-10 0 10 20 30 40-20 50 ˚C
or SAE 10W-30YAMALUBE 4 (10W-30)
YAMALUBE 4 (20W-40)or SAE 20W-40
Recommended engine oil gradeAPI service SG type or higher, JASO stan-dard MA
Engine oil quantityPeriodic oil change
1.00 L (1.06 US qt) (0.88 Imp.qt)Final transmission oil
TypeSAE85W-140(GL5)
Quantity0.13 L (0.14 US qt) (0.11 Imp.qt)
Air filterAir filter element
Oil-coated paper elementFuel
Recommended fuelUnleaded gasoline only
Fuel tank capacity4.7 L (1.24 US gal) (1.03 Imp.gal)
CarburetorManufacturer
Mikuni
Type x quantityBS26 x 1
Spark plug (s)Manufacturer/model
NGK/CR7ESpark plug gap
0.7-0.8 mm (0.028-0.031 in)Clutch
Clutch typeDry, centrifugal automatic
TransmissionPrimary reduction system
Helical gearPrimary reduction ratio
40/15 (2.666)Secondary reduction system
Spur gearSecondary reduction ratio
38/13 (2.923)Transmission type
V-belt automaticOperation
Centrifugal automatic typeChassis
Frame typeSteel tube backbone
Caster angle32.00 degree
Trail75.0 mm (2.95 in)
Front tireType
TubelessSize
3.50-10 51J
5YR-F8199-14_ch8.pmd 2007/05/24, 19:581
8-2
1
2
3
4
5
6
7
8
9
SPECIFICATIONSManufacturer/model
CHENG SHIN/C-922LRear tire
TypeTubeless
Size3.50-10 51J
Manufacturer/modelCHENG SHIN/C-6007
LoadingMaximum load
144 kg (317 lb)Tire air pressure (measured on cold tires)
Loading condition0-90 kg (0-198 lb)
Front150 kPa (22 psi) (1.50 kgf/cm2) (1.50 bar)
Rear200 kPa (29 psi) (2.00 kgf/cm2) (2.00 bar)
Loading condition90 kg - maximum load
Front150 kPa (22 psi) (1.50 kgf/cm2) (1.50 bar)
Rear225 kPa (33 psi) (2.25 kgf/cm2) (2.25 bar)
Front wheelWheel type
Cast wheelRim size
J10 x MT2.5Rear wheel
Wheel typeCast wheel
Rim sizeJ10 x MT2.5
Front brakeType
Single disc brakeOperation
Right hand operationRecommended fluid
DOT 3 or 4Rear brake
TypeDrum brake
OperationLeft hand operation
Front suspensionType
Telescopic forkSpring/shock absorber type
Coil spring/oil damperWheel travel
59.0 mm (2.32 in)Rear suspension
TypeUnit swing
Spring/shock absorber typeCoil spring/oil damper
Wheel travel54.0 mm (2.13 in)
Electrical systemIgnition system
CDICharging system
CDI magnetoBattery
ModelGTX7A-BS / YTX7A-BS
Voltage, capacity12 V, 6.0 Ah
HeadlightBulb type
Halogen bulbBulb voltage, wattage x quantity
Headlight12 V, 60 W/55.0 W x 1
Tail/brake light12 V, 8.0 W/27.0 W x 1
Front turn signal light12 V, 10.0 W x 2
Rear turn signal light12 V, 10.0 W x 2
License plate light12 V, 8.0 W x 1
Meter lighting14 V, 3.0 W x 1
Meter lighting (fuel meter)14 V, 3.0 W x 1
High beam indicator light14 V, 3.0 W x 1
Turn signal indicator light12 V, 1.7 W x 1
FusesMain fuse
10.0 A
5YR-F8199-14_ch8.pmd 2007/05/24, 19:582
9-1
1
2
3
4
5
6
7
8
9
CONSUMER INFORMATIONEAU26351
Identification numbersRecord the key identification number,vehicle identification number and modellabel information in the spaces providedbelow for assistance when orderingspare parts from a Yamaha dealer orfor reference in case the vehicle is sto-len.
KEY IDENTIFICATION NUMBER:
VEHICLE IDENTIFICATION NUMBER:
MODEL LABEL INFORMATION:
Identification numbers<IXE>
Key identification number<IXE>
Vehicle identification number<IXE>EAU26342
CONSUMER INFORMATIONEAU26410
Vehicle identification number
1
ZAUM00**
1. Vehicle identification number
The vehicle identification number isstamped into the frame.
NOTE:The vehicle identification number isused to identify your motorcycle andmay be used to register your motorcyclewith the licensing authority in your area.
EAU26390
Key identification number
1
ZAUM00**
1. Key identification number
The key identification number isstamped into the key.Record this number in the space pro-vided and use it for reference when or-dering a new key.
5YR-F8199-14_ch9ind.pmd 2007/05/21, 17:421
9-2
1
2
3
4
5
6
7
8
9
CONSUMER INFORMATIONModel label<IXE>
EAU26460
Model label
1
ZAUM00**
1. Model label
The model label is affixed to the loca-tion shown. Record the information onthis label in the space provided. Thisinformation will be needed when order-ing spare parts from a Yamaha dealer.
5YR-F8199-14_ch9ind.pmd 2007/05/21, 17:422
9-3
1
2
3
4
5
6
7
8
9
CONSUMER INFORMATIONSafety defects, reporting<IXE>
EAU26551
Reporting safety defectsIf you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immedi-ately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation,U.S.A. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a groupof vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problemsbetween you, your dealer, or Yamaha Motor Corporation, U.S.A.
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, DC 20590. You can also obtainother information about motor vehicle safety from http://www.safercar.gov.
5YR-F8199-14_ch9ind.pmd 2007/05/21, 17:423
9-4
1
2
3
4
5
6
7
8
9
CONSUMER INFORMATIONNoise regulation<IXE>
Exhaust systemMufflerExhaust pipeSilencer
Intake systemAir cleaner caseAir cleaner elementIntake duct
EAU26560
Motorcycle noise regulationTAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED:Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person otherthan for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any newvehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the useof the vehicle after such device or element of design has been removed or rendered inoperative by any person.
“AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW”.
These acts include tampering with the following systems; i.e., modification, removal, etc.
5YR-F8199-14_ch9ind.pmd 2007/05/21, 17:424
9-5
1
2
3
4
5
6
7
8
9
CONSUMER INFORMATIONEAU26600
Maintenance recordCopies of work orders and/or receipts for parts purchased and installed on your motorcycle will be required to documentthat maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as areminder that maintenance work is required. It is not acceptable proof of maintenance work.
Maintenance record<IXE>
Maintenanceinterval
Date ofservice Mileage Servicing dealer
name and address Remarks
600 mi(1000 km) or
1 month
2000 mi(4000 km) or
6 months
4000 mi(7000 km) or12 months
6000 mi(10000 km) or
18 months
8000 mi(13000 km) or
24 months
10000 mi(16000 km) or
30 months
12000 mi(19000 km) or
36 months
14000 mi(22000 km) or
42 months
5YR-F8199-14_ch9ind.pmd 2007/05/21, 17:425
9-6
1
2
3
4
5
6
7
8
9
CONSUMER INFORMATION
16000 mi(25000 km) or
48 months
18000 mi(28000 km) or
54 months
20000 mi(31000 km) or
60 months
Maintenanceinterval
Date ofservice Mileage Servicing dealer
name and address Remarks
5YR-F8199-14_ch9ind.pmd 2007/05/21, 17:426
9-7
1
2
3
4
5
6
7
8
9
CONSUMER INFORMATIONWarranty, limited<IXE>
EAU26681
YAMAHA MOTOR CORPORATION, U.S.A.RIVA LIMITED WARRANTY
5YR-F8199-14_ch9ind.pmd 2007/05/21, 17:427
9-8
1
2
3
4
5
6
7
8
9
CONSUMER INFORMATION
5YR-F8199-14_ch9ind.pmd 2007/05/21, 17:428
9-9
1
2
3
4
5
6
7
8
9
CONSUMER INFORMATIONWarranty, extended<IXE>
Keep your Yamaha protected even after your warranty expires with genuine Yamaha Extended Service (Y.E.S.).
Y.E.S. is designed and administered by Yamaha Motor Corporation to provide maximum owner satisfaction. You get uninterrupted factory-backed coverage for extra peace of mind.
Y.E.S. is flexible. You choose the plan that’s right foryou: 12 months, 24 months, 36 months or, on certain models, even 48 months beyond your warranty period.
Y.E.S. is designed and administered by the same Yamaha people who handle your warranty – and itshows in the comprehensive coverage benefits. There are no mileage limitations. Coverage isn’t limited to “moving parts” or the “drive train” like many other plans. And Y.E.S. covers manufacturing defects just like the warranty. See the sample contract at your Yamahadealer to see how comforting uninterrupted factory-backed protection can be.
You don’t have to pay anything for covered repairs. There’s no deductible to pay, and repairs aren’t“pro-rated.” You don’t have any “out-of-pocket” expenses for covered repairs.
In addition, Travel and Recreation Interruption Protection (TRIP) is included at no extra cost. TRIP gives you up to $150 reimbursement per occurrence for any reasonable expenses you incur because your Yamaha needs covered service: replacement vehicle rental, emergency towing, phone calls, even food and lodging when you are away from home. This superb coverage goes into effect when you purchase Y.E.S., so it applies to any warranty repairs as well as covered repairs during your entire Y.E.S. plan period.
Y.E.S. coverage is honored at any authorized Yamaha dealer nationwide.
Y.E.S. coverage is transferable to a new owner if yousell or trade-in. That can make your Yamaha much more valuable!
This excellent Y.E.S. plan coverage is only available to Yamaha owners like you, and only while your Yamaha is still within the Yamaha Limited Warranty period. So visit your authorized Yamaha dealer to get all the facts. He can show you how easy it is to protect your investment with Yamaha Extended Service.
EAU26750
YAMAHA EXTENDED SERVICE (Y.E.S.)
5YR-F8199-14_ch9ind.pmd 2007/05/21, 17:429
9-10
1
2
3
4
5
6
7
8
9
CONSUMER INFORMATION
We urge you to act now. You’ll get the excellent benefits of TRIP coverage right away, and you’ll rest easy knowing you’ll have strong factory-backed protection even after your Yamaha Limited Warranty expires.
A special note:If visiting your dealer isn’t convenient, contact Yamaha with your Primary ID number (your frame number). We’ll be happy to help you get the Y.E.S. coverage you need.
Yamaha Service MarketingP.O. Box 6555Cypress, CA 906301-(866)-YES-EXTD (1-866-937-3983)
5YR-F8199-14_ch9ind.pmd 2007/05/21, 17:4210
INDEXA
Acceleration and deceleration ................. 5-2Air filter and V-belt case air filter
elements .............................................. 6-12B
Battery .................................................... 6-23Brake fluid level, checking ..................... 6-19Brake fluid, changing ............................. 6-20Brake lever, front ...................................... 3-4Brake lever, rear ....................................... 3-4Brake levers, lubricating ......................... 6-21Brake pads and shoes, checking ........... 6-18Braking ..................................................... 5-2
CCables, checking and lubricating ........... 6-20Carburetor .............................................. 6-14Care .......................................................... 7-1Carrier ...................................................... 3-9Catalytic converter ................................... 3-6Centerstand and sidestand, checking and lu-
bricating ............................................... 6-21D
Dimmer switch .......................................... 3-3E
Engine break-in ........................................ 5-3Engine oil and oil strainer ........................ 6-9Engine stop switch ................................... 3-3
FFinal transmission oil ............................. 6-11Front brake lever free play, checking ..... 6-17Front fork, checking ............................... 6-22Fuel .......................................................... 3-5Fuel gauge ............................................... 3-2Fuel tank cap ........................................... 3-4
Fuse, replacing ...................................... 6-25H
Handlebar switches .................................. 3-3Headlight bulb, replacing ....................... 6-25Helmet holder ........................................... 3-7High beam indicator light ......................... 3-2Horn switch .............................................. 3-3
IIdentification numbers .............................. 9-1Ignition circuit cut-off system ................. 3-10Indicator lights .......................................... 3-2
KKey identification number ......................... 9-1Kickstarter ................................................ 3-6
LLabels, location of .................................... 1-6Luggage hook .......................................... 3-9
MMain switch/steering lock ......................... 3-1Maintenance and lubrication, periodic ..... 6-4Maintenance record ................................. 9-5Maintenance, emission control system ... 6-3Maintenance, periodic .............................. 6-1Model label ............................................... 9-2
NNoise regulation ....................................... 9-4
PPanels, removing and installing ............... 6-8Parking ..................................................... 5-3Part locations ........................................... 2-1Pre-operation check list ........................... 4-2
RRear brake lever free play, adjusting ..... 6-17
SSafe-riding points ..................................... 1-4Safety defects, reporting .......................... 9-3Safety information .................................... 1-1Seat .......................................................... 3-7Sidestand ............................................... 3-10Spark plug, checking ............................... 6-8Specifications ........................................... 8-1Speedometer unit ..................................... 3-2Start switch .............................................. 3-3Starting a cold engine .............................. 5-1Starting off ................................................ 5-2Steering, checking ................................. 6-22Storage ..................................................... 7-3Storage compartment .............................. 3-8
TTail/brake light bulb, replacing ................ 6-27Throttle cable free play, checking .......... 6-14Throttle grip and cable, checking and
lubricating ............................................ 6-20Tires ....................................................... 6-15Tool kit ...................................................... 6-1Troubleshooting ........................................ 6-8Troubleshooting chart ............................ 6-29Turn signal indicator light ......................... 3-2Turn signal light bulb, replacing ............. 6-27Turn signal switch ..................................... 3-3
VVehicle identification number ................... 9-1
WWarranty, extended .................................. 9-9Warranty, limited ....................................... 9-7Wheel bearings, checking ...................... 6-23Wheels ................................................... 6-16
5YR-F8199-14_ch9ind.pmd 2007/05/21, 17:4211
INDEX
5YR-F8199-14_ch9ind.pmd 2007/05/21, 17:4212
1
2
3
4
5
6
7
8
9
5YR-F8199-14_ch9ind.pmd 2007/05/21, 17:4213
1
2
3
4
5
6
7
8
9
5YR-F8199-14_ch9ind.pmd 2007/05/21, 17:4214
1
2
3
4
5
6
7
8
9
5YR-F8199-14_ch9ind.pmd 2007/05/21, 17:4215
1
2
3
4
5
6
7
8
9
5YR-F8199-14_ch9ind.pmd 2007/05/21, 17:4216
YAMAHA MOTOR TAIWAN CO., LTD
PRINTED IN TAIWAN2007.07-0.8×××××1!
(E)
5YR-F8199-14_ch0cv.pmd 2007/05/21, 17:381