yk style f wiring diagram liquid ... - johnson controls

24
PRODUCT DRAWING YORK INTERNATIONAL CORPORATION P.O. Box 1592, York, PA 17405 CONTRACTOR _______________________ PURCHASER ____________________________________________ ORDER NO. _________________________ JOB NAME ______________________________________________ YORK CONTRACT NO. _________________ LOCATION _____________________________________________ YORK ORDER NO. ____________________ ENGINEER ______________________________________________ REFERENCE DATE ________ APPROVAL DATE ________ CONSTRUCTION DATE ________ Supersedes: 160.73-PW3 (703) Form 160.73-PW3 (405) WIRING DIAGRAM, MAXE™ MODEL YK (STYLE F) LIQUID CHILLERS OPTIVIEW CONTROL CENTER WITH VARIABLE FREQUENCY DRIVE JOB DATA: CHILLER MODEL NO. YK ________________________________________________________ NO. OF UNITS _____________ COMPRESSOR MOTOR ______________ VOLTS, 3-PHASE, _____________ Hz OIL PUMP MOTOR _____________ VOLTS, 3-PHASE, _____________ Hz, _____________FLA REMARKS:

Upload: others

Post on 18-Dec-2021

8 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: YK Style F Wiring Diagram Liquid ... - Johnson Controls

PRODUCT DRAWING YORK INTERNATIONAL CORPORATION P.O. Box 1592, York, PA 17405

CONTRACTOR _______________________ PURCHASER ____________________________________________ ORDER NO. _________________________ JOB NAME ______________________________________________ YORK CONTRACT NO. _________________ LOCATION _____________________________________________ YORK ORDER NO. ____________________ ENGINEER ______________________________________________

REFERENCE DATE ________ APPROVAL DATE ________ CONSTRUCTION DATE ________

Supersedes: 160.73-PW3 (703) Form 160.73-PW3 (405)

WIRING DIAGRAM, MAXE™MODEL YK (STYLE F) LIQUID CHILL ERS

OPTIVIEW CONTROL CENTERWITH VARIABLE FREQUENCY DRIVE

JOB DATA:

CHILLER MODEL NO. YK ________________________________________________________NO. OF UNITS _____________COMPRESSOR MOTOR ______________ VOLTS, 3-PHASE, _____________ HzOIL PUMP MOTOR _____________ VOLTS, 3-PHASE, _____________ Hz, _____________FLA

REMARKS:

Page 2: YK Style F Wiring Diagram Liquid ... - Johnson Controls

YORK INTERNATIONAL2

FORM 160.73-PW3 (405)

ELEMENTARY DIAGRAM(UL APPLICATIONS ONLY)

LD10895

FIG. 1 – ELEMENTARY DIAGRAM (UL APPLICATIONS ONLY)

Page 3: YK Style F Wiring Diagram Liquid ... - Johnson Controls

FORM 160.73-PW3 (405)

3YORK INTERNATIONAL

ELEMENTARY DIAGRAM (CON'T)(UL APPLICATIONS ONLY)

ELEMENTARY DIAGRAM (UL APPLICATIONS ONLY) (CONT)LD10896

Page 4: YK Style F Wiring Diagram Liquid ... - Johnson Controls

YORK INTERNATIONAL4

FORM 160.73-PW3 (405)

LD10897

ELEMENTARY DIAGRAM(CE APPLICATIONS ONLY)

FIG. 2 – ELEMENTARY DIAGRAM (CE APPLICATIONS ONLY)

Page 5: YK Style F Wiring Diagram Liquid ... - Johnson Controls

FORM 160.73-PW3 (405)

5YORK INTERNATIONAL

LD10898

ELEMENTARY DIAGRAM (CON'T)(CE APPLICATIONS ONLY)

ELEMENTARY DIAGRAM (CE APPLICATIONS ONLY) (CON'T)

Page 6: YK Style F Wiring Diagram Liquid ... - Johnson Controls

YORK INTERNATIONAL6

FORM 160.73-PW3 (405)

LD10899FIG. 3 – ELEMENTARY DIAGRAM

ELEMENTARY DIAGRAM

Page 7: YK Style F Wiring Diagram Liquid ... - Johnson Controls

FORM 160.73-PW3 (405)

7YORK INTERNATIONAL

LD10900

ELEMENTARY DIAGRAM (CON'T)

ELEMENTARY DIAGRAM (CON'T)

Page 8: YK Style F Wiring Diagram Liquid ... - Johnson Controls

YORK INTERNATIONAL8

FORM 160.73-PW3 (405)

LD10901FIG. 4 – ELEMENTARY DIAGRAM (MICROBOARD 031-02430)

ELEMENTARY DIAGRAM (MICROBOARD 031-02430)

Page 9: YK Style F Wiring Diagram Liquid ... - Johnson Controls

FORM 160.73-PW3 (405)

9YORK INTERNATIONAL

LD10902

ELEMENTARY DIAGRAM (MICROBOARD 031-02430)(CON'T)

ELEMENTARY DIAGRAM (MICROBOARD 031-02430) (CON'T)

Page 10: YK Style F Wiring Diagram Liquid ... - Johnson Controls

YORK INTERNATIONAL10

FORM 160.73-PW3 (405)

LEGEND

LD09000

Page 11: YK Style F Wiring Diagram Liquid ... - Johnson Controls

FORM 160.73-PW3 (405)

11YORK INTERNATIONAL

LD10915

DISPLAY INTERFACE BOARD

FIG. 5 – DISPLAY INTERFACE BOARD

NOTES: 1. This wiring diagram describes the standard elec tron ic

con trol scheme for use with a YORK V.S.D. for details of standard modifi cations, refer to Product Form 160.54-PW7.

2. Field wiring to be in accordance with the National Elec tri cal Code as well as all other applicable codes and spec i fi ca tions. See Product Form 160.54-PW6 for fi eld wiring con nec tions.

3. Numbers along the left side of diagram are line iden ti -fi ca tion numbers. The numbers along the right side in di cate the line num ber location of relay contacts. An un der lined con tact lo ca tion signifi es a normally closed con tact.

4. Main control panel Class 1 fi eld wiring terminal con- nec tion points are indicated by numbers within a rect an gle, i.e. 15 . Main con trol panel factory wiring terminal con- nec tion points are in di cat ed by numbers within a tri an gle, i.e. 5 . Com po nent terminal markings are in di cat ed by num bers within a circle, i.e. C1 . Num bers ad ja cent to cir cuit lines are the cir cuit iden ti fi ca tion num bers.

5. To cycle unit on and off automatically with contacts oth er than those shown, install a cycling device between ter mi nals 1 & 13 (line 37) (see note 7). If a cycling device is installed, jumper must be removed between ter mi nals 1 & 13 .

6. To stop unit and not permit it to start again, install a stop device between terminals 1 & 8 (Line 33) (see note 7). A re mote start-stop switch may be connected to ter mi nals 1 , 7 & 8 (Lines 32 & 33) (see note 7). Remote start-stop switch (Line 32) is op er a tive only in the “re mote” op er at ing mode.

7. Device contact rating to be 5 milliamperes @ 115 volts A.C.

8. Contact rating is 5 Amps resistive @ 120 volts A.C. or 240 volts A.C.

10. For wiring diagram of V.S.D refer to product form 160.49-PW9.

11. A jumper is installed between terminals 24 & 25 for normal operation.

CAUTION: The jumper is the only connection permitted between terminals 24 & 25 . Connections of any other devices to either terminals 24 & 25 may cause inadver-tent compressor start-up.

12. Stop contact on V.S.D logic board is set to trip at 105% FLA.

13. Contact rating is 5 Amps resistive @ 250 Volts A.C. & 30 Volts D.C., 2 Amp Inductive (.4 PF) @ 250 Volts A.C. & 30 Volts D.C.

14. Field connected control power supply is not required, as control transformer is supplied on the V.S.D.

15. For high and low voltage units, the factory supplied jumper between 15 & 53 must be removed when elec-tromechanical starter overloads and/or safety devices are used. For high voltage (2300-4160) UL and CUL ap-proved units only. Elecromechanical compressor motor starter overloads (normally closed) must be connected between 15 & 53 .

16. Each 115VAC fi eld-connected inductive load: i.e. relay coil, mo tor starter coil, etc., shall have a transient sup- pres sor wired in parallel with its coil, physically located at the coil. Spare tran sient suppressors and control cir cuit fuses are sup plied in a bag attached to green ground screw in lower left corner of control panel.

17. Resistor for use with Belimo actuator. Remove resis-tor if hot gas actuator is a Dodge Engineering, Bray or Landis-Staefa actuator.

Page 12: YK Style F Wiring Diagram Liquid ... - Johnson Controls

YORK INTERNATIONAL12

FORM 160.73-PW3 (405)

LD10903FIG. 6 – CONNECTION DIAGRAM (UL APPLICATIONS ONLY)

CONNECTION DIAGRAM(UL APPLICATIONS ONLY)

Page 13: YK Style F Wiring Diagram Liquid ... - Johnson Controls

FORM 160.73-PW3 (405)

13YORK INTERNATIONAL

LD10904

CONNECTION DIAGRAM (CON'T)(UL APPLICATIONS ONLY)

CONNECTION DIAGRAM (UL APPLICATIONS ONLY) (CON'T)

Page 14: YK Style F Wiring Diagram Liquid ... - Johnson Controls

YORK INTERNATIONAL14

FORM 160.73-PW3 (405)

LD10905FIG. 7 – CONNECTION DIAGRAM (CE APPLICATION ONLY)

CONNECTION DIAGRAM(CE APPLICATION ONLY)

Page 15: YK Style F Wiring Diagram Liquid ... - Johnson Controls

FORM 160.73-PW3 (405)

15YORK INTERNATIONAL

LD10906

CONNECTION DIAGRAM (CON'T)(CE APPLICATION ONLY)

CONNECTION DIAGRAM (CE APPLICATION ONLY) (CON'T)

Page 16: YK Style F Wiring Diagram Liquid ... - Johnson Controls

YORK INTERNATIONAL16

FORM 160.73-PW3 (405)

LD10907FIG. 8 – CONNECTION DIAGRAM

CONNECTION DIAGRAM

Page 17: YK Style F Wiring Diagram Liquid ... - Johnson Controls

FORM 160.73-PW3 (405)

17YORK INTERNATIONAL

LD10908CONNECTION DIAGRAM (CON'T)

CONNECTION DIAGRAM (CON'T)

Page 18: YK Style F Wiring Diagram Liquid ... - Johnson Controls

YORK INTERNATIONAL18

FORM 160.73-PW3 (405)

LD10909FIG. 9 – CONNECTIONS TO CONTROL PANEL

CONNECTION DIAGRAM

Page 19: YK Style F Wiring Diagram Liquid ... - Johnson Controls

FORM 160.73-PW3 (405)

19YORK INTERNATIONAL

LD10910

CONNECTION DIAGRAM (CON'T)

CONNECTIONS TO CONTROL PANEL (CON'T)

Page 20: YK Style F Wiring Diagram Liquid ... - Johnson Controls

YORK INTERNATIONAL20

FORM 160.73-PW3 (405)

LD10911FIG. 10 – CONNECTION DIAGRAM

CONNECTION DIAGRAM

Page 21: YK Style F Wiring Diagram Liquid ... - Johnson Controls

FORM 160.73-PW3 (405)

21YORK INTERNATIONAL

LD10912

CONNECTION DIAGRAM (CON'T)

CONNECTION DIAGRAM (CON'T)

Page 22: YK Style F Wiring Diagram Liquid ... - Johnson Controls

YORK INTERNATIONAL22

FORM 160.73-PW3 (405)

FIG. 11 – WIRING FOR 380V THRU 480V UNITS

VARIABLE SPEED OIL PUMP DRIVE PANEL

LD10913

Page 23: YK Style F Wiring Diagram Liquid ... - Johnson Controls

FORM 160.73-PW3 (405)

23YORK INTERNATIONAL

LD10914

PRESSURE - TEMPERATURE CHART

Page 24: YK Style F Wiring Diagram Liquid ... - Johnson Controls

(717) 771-7890www.york.com

P.O. Box 1592, York, Pennsylvania USA 17405-1592 Subject to change without notice. Printed in USACopyright © by YORK International Corporation 2005 ALL RIGHTS RESERVEDForm 160.73-PW3 (405) Supersedes: 160.73-PW3 (703)