z-wave wireless siren and strobe · integration manual for mi casa verde vera 2/3/lite (ui5) safety...

1

PO Box 353

Rosanna, Victoria

3084

Australia

Digital Home Systems Pty Ltd Integration Manual for Mi Casa Verde Vera 2/3/Lite (UI5)

S A FE TY F IRS T

Install the batteries in the current

polarity.

Z-Wave Wireless Siren and Strobe DHS-ZWSR-01

1. Installing the device

1.1 Refer to installation manual of the DHS-ZWSR-01.

2. Configuring the device

Note: Before including the product to your Z-Wave network it is advised to perform removal procedure to reset the device

network settings.

2.1 Log in to your system, type the IP of your Vera in your browser. Alternatively, if you have internet connection you can

go to https://findvera.com/ and follow the instructions.

PO Box 353

Rosanna, Victoria

3084

Australia 2


1.2 Exclusion from Z-Wave home network

1.2.1 Press the Z-Wave button on the Vera for at least 7 sec and release, the Z-Wave LED will start to flash fast, check the

system interface for the following message.

1.2.2 Press the switch at least for 1 second and release on the DHS-ZWSR-01, the Z-Wave LED on the Vera will flash

quickly for a couple seconds, the following message will appear on the system interface.

1.3 Inclusion to Z-Wave home network

1.3.1 Press the Z-Wave button on the Vera, the Z-Wave LED on the Vera will flash slowly, the following message will

appear on the system interface.

1.3.2 Press the switch at least for 1 second and release on the DHS-ZWSR-01, the Z-Wave LED on the Vera will flash

quickly for a couple seconds, the following message will appear on the system interface.

1.3.3 Press the Z-Wave button on the Vera to exit the inclusion mode, the Vera will process Z-Wave reconfiguration.

please note that the Node and Device number in the above screen are only an examples

1.4 After the Vera finishes Z-Wave reconfiguration and the Z-Wave LED is on, in the system interface go to ‘Devices/All’, you

will find DHS-ZWSR-01 as four devices: ‘_Binary Light’, under no room.

3

PO Box 353

Rosanna, Victoria

3084

Australia


Note: After adding a new device go to ‘SETUP/Z Wave Settings’, choose ‘Repair’ set preferable settings and press ’Go’.

This action will check and build a mash communication system between all new and old devices.

2.5 Associate the device to a room and rename it

2.5.1 Go to ‘Setup/Rooms’, and add rooms. Click the ‘SAVE’ button on the main screen after making any changes.

2.5.2 Go to ‘Devices/All’, click on wrench key and choose preferable from the drop-down list on the right.

2.5.3 In the ‘Advanced’ tab you can change the name of the device, at the left hand side you can find the device ID which

is useful for future automation scenes. You can also set up more configurations under the ‘Setting’ tab, such as

polling time stress test, etc.

PO Box 353

Rosanna, Victoria

3084

Australia 4


2.6 Configuration

2.6.1 Go to the ‘Wrench key/Device Options’, under the ‘Configuration settings’ press add.

Parameter 0 defines the Siren/Strobe mode, Data Size 1 byte dec, Desired Value 0(siren and strobe enabled, de

fault), 1(Siren only), 2(Strobe only).

Parameter 1 defines the Alarm auto stop time, Data Size 1 byte dec, Desired Value 0(30 seconds, default),

2(60 seconds), 3(siren will not automatically stop). To save and finish close the dialog window of the dimmer

and press SAVE.

2.7 How to build a scene

2.7.1Go to ‘AUTOMATION/New scene’, you will get a screen with all your devices. Choose which device will be triggered

and what it’s state should change to when the scene is on (for example the ‘Corner Light’ will go ON).

5

PO Box 353

Rosanna, Victoria

3084

Australia


2.7.2 Go to ‘TRIGGERS’, Give a name for the scene and choose from the list which devices will act as the trigger (for

example the name is ‘door_1’ and ‘door/window sensor’ is the trigger).

2.6.3 Choose ‘What type of event will act as the trigger?’ (for example ‘A sensor door/window is trigged’)

Choose a name for the trigger (for example ‘scene_1’)

Choose the current state of the device (for example ‘Device is tripped’)

You can also choose to receive a notification about the scene.

PO Box 353

Rosanna, Victoria

3084

Australia 6


Specification are subject to change without further notice

The information in this document is subject to change without notice. Digital Home Systems Pty Ltd (DHS) does not make any representations or warranties (implied or otherwise) regarding the

accuracy and completeness of this document and shell in no event be liable for any loss of profit or any commercial damage,

including but not limited to special, incidental, consequential, or other damage.

TRADEMARKS All trademarks and registered trademarks are the property of their respective owners or companies.

DHS One (1) Year Limited Warranty Digital Home Systems Pty Ltd warranty this DHS branded hardware product against defects in materials and workmanship under normal use for period of one

(1) year from the date of retails purchase by the original end user purchaser (‘Warranty Period’). PLEASE NOTE: breaking security label will void the warranty.

To see complete terms and conditions browse to http://www.digitslhomesystems.com.au/images/stories/DHS_Terms_and_conditions.pdf

Product of Digital Home Systems Pty Ltd

See all range of compatible devices at www.digitalhomesystems.com.au

Enquiries Sales and marketing Email: [email protected]

© 2012 Digital Home Systems Pty Ltd. All rights reserved.

2.6.4 Delay, (for example to switch on the light for 5 seconds). Go to ’Manage Delays’, add 5 Seconds and press ‘Close’,

then choose the 5 seconds from the list, an arrow will appear above all the ON/OFF buttons of the devices, press on

the arrow to turn it red. Now when the ‘door/window sensor’ is trigged the ‘light corner’ will switch ON for 5

seconds.

z-wave wireless siren and strobe · integration manual for mi casa verde vera 2/3/lite (ui5) safety...

Documents