arcat · web viewarcat ... 12494-1

SECTION 12494WINDOW SHADES

Copyright 2008 - 2008 ARCAT, Inc. - All rights reserved

** NOTE TO SPECIFIER ** Draper, Inc.; window shade products..This section is based on the products of Draper, Inc., which is located at:411 S. Pearl StreetP. O. Box 425Spiceland, IN 47385-0425Tel: (800) 238-7999Fax: (765)987-7142Email:[email protected]:www.draperinc.com[Click Here] for additional information.

Draper is a leader in the manufacture of window shades, projection screens, and gymnasium equipment. Founded in 1902, Draper maintains a tradition of quality and service. Draper products include FlexShade roller-operated and fixed window shades.

Window shades reflect light and heat from the sun, reducing the amount of energy required to cool the building. Motorized window shades can automatically adjust to compensate for the changing shade requirements throughout the day. DRAPER's white paper, Shades of LEED, provides an in-depth explanation of how our solar control shading systems can contribute to LEED points and credits. In addition, shades can reduce or eliminate uncomfortable glare for workers, while still allowing ambient sunlighting and view-through to the outside. The construction of window shades has become more friendly to the environment as well by including PVC-free fabrics, recyclable fabrics and lean manufacturing processes.

Our spectrum of fabric colors and styles is unmatched anywhere. And we offer the broadest variety of operator styles in the industry.

This section can be used for specifying both manually operated and motorized Draper Flexshades and LightBloc FlexShades, an opaque fabric window shade system for complete blackout of window opening.Chain and Clutch Operated FlexShadeCrank Operated FlexShadeSpring Roller Operated FlexShadeMotorized FlexShadeLightBloc FlexShade

See our SpecWizard:Click Here

PART 1 GENERAL

12494-1

1.1 SECTION INCLUDES** NOTE TO SPECIFIER ** Delete items below not required for project.

A. Manually operated, roll-up fabric interior window shades including mounting and operating hardware.

B. Motorized, roll-up fabric interior window shades including motor operator, controls, and mounting hardware.

C. Opaque window shade system: Manually operated, roll-up fabric opaque window shade system for complete blackout of window opening including side and bottom channels, headbox, manual operator, and mounting hardware.

D. Opaque window shade system: Motorized, roll-up fabric opaque window shade system for complete blackout of window opening including side and bottom channels, headbox, motorized operator, controls, and mounting hardware.

1.2 RELATED SECTIONS** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.

A. Section 06100 - Rough Carpentry: Blocking for support of window shade hardware.

B. Section 07900 - Joint Sealers: Sealants for perimeter of shade system.

C. Section 09260 - Gypsum Board Assemblies: Suspended gypsum board ceilings to contain recessed window shade pockets.

D. Section 09510 - Acoustical Ceilings: Suspended acoustical panel ceilings to contain recessed window shade pockets.

E. Section 11132 - Motorized Projection Screens: Motorized projection screens to be interfaced with shade controls.

F. Section 11136 - Motorized Projector Lifts: Motorized projector lifts and mounts to be interfaced with shade controls.

G. Division 16 - Electrical: Electrical supply, conduit, and wiring for motorized window shades.

1.3 REFERENCES** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.

A. NFPA 70 - National Electrical Code.

B. NFPA 701-99 - Fire Tests for Flame-Resistant Textiles and Films.

C. GREENGUARD Environmental Institute Children & Schools.

D. US Green Building Council.

1.4 SUBMITTALS

A. Submit under provisions of Section 01330 - Submittal Procedures:

B. Product Data: Manufacturer's data sheets on each product specified, including:1. Preparation instructions and recommendations.2. Installation and maintenance instructions.

12494-2

3. Styles, material descriptions, dimensions of individual components, profiles, features, finishes and operating instructions.

4. Storage and handling requirements and recommendations.5. Mounting details and installation methods.

** NOTE TO SPECIFIER ** Delete the following paragraph for manual operation shades.6. Typical wiring diagrams including integration of motor controllers with building

management system, audiovisual and lighting control systems as applicable.** NOTE TO SPECIFIER ** Include the following paragraph for projects with complex requirements for window treatment. Delete if not required.

C. Shop Drawings: Plans, elevations, sections, product details, installation details, operational clearances, wiring diagrams and relationship to adjacent work.

** NOTE TO SPECIFIER ** Delete the following paragraphs if LEED is not applicable.

D. LEED Submittals: Provide documentation of how the requirements of Credit will be met.

E. Window Treatment Schedule: For all roller shades. Use same room designations as indicated on the Drawings, field verified window dimensions, quantities, type of shade, controls, fabric, and color, and include opening sizes and key to typical mounting details.

** NOTE TO SPECIFIER ** Delete Selection Samples paragraph if colors and shade fabrics have already been selected.

F. Selection Samples: For each finish product specified, two complete sets of shade cloth options and aluminum finish color samples representing manufacturer's full range of available colors and patterns.

G. Verification Samples: For each finish product specified, two complete sets of shade components, unassembled, demonstrating compliance with specified requirements. Shade fabric sample and aluminum finish sample as selected, representing actual product, color, and patterns. Mark face of material to indicate interior faces.

H. Maintenance Data: Methods for maintaining roller shades, precautions regarding cleaning materials and methods, instructions for operating hardware and controls.

I. Manufacturer's Certificates: Certify products meet or exceed specified requirements.

1.5 QUALITY ASSURANCE

A. Manufacturer Qualifications: Obtain roller shades through one source from a single manufacturer with a minimum of twenty years experience in manufacturing products comparable to those specified in this section.

B. NFPA Flame-Test: Passes NFPA 701. Materials tested shall be identical to products proposed for use.

** NOTE TO SPECIFIER ** Include a mock-up if the project size and/or quality warrant taking such a precaution. The following is one example of how a mock-up on a large project might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project.

C. Mock-Up: Provide a mock-up of one of each type roller shade assembly specified for evaluation of mounting, appearance and accessories.1. Locate mock-up in window(s) designated by Architect.2. Do not proceed with remaining work until mock-up is accepted by Architect.

1.6 DELIVERY, STORAGE, AND HANDLING

12494-3

A. Do not deliver window shades until building is enclosed and construction within spaces where shades will be installed is substantially complete.

B. Deliver products in manufacturer's original, unopened, undamaged containers with labels intact.

C. Label containers and shades according to Window Shade Schedule.

D. Store products in manufacturer's unopened packaging until ready for installation.

1.7 SEQUENCING

A. Ensure that locating templates and other information required for installation of products of this section are furnished to affected trades in time to prevent interruption of construction progress.

B. Ensure that products of this section are supplied to affected trades in time to prevent interruption of construction progress.

1.8 PROJECT CONDITIONS

A. Install roller shades after finish work and ambient temperature, humidity and ventilation conditions are maintained at levels recommended for project upon completion.

1.9 WARRANTY

A. Hardware and Shade Fabric: Draper's standard twenty-five year limited warranty.** NOTE TO SPECIFIER ** Include the following paragraph as applicable.

B. Spring Roller Shades: Draper's standard ten year limited warranty.** NOTE TO SPECIFIER ** Delete the following paragraph for manual operation.

C. Motors and Controls: Draper's standard five year limited warranty.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Acceptable Manufacturer: Draper, Inc., which is located at: 411 S. Pearl P. O. Box 425 ; Spiceland, IN 47385-0425; Toll Free Tel: 800-238-7999; Tel: 765-987-7999; Email:request info; Web:www.draperinc.com

** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.

B. Substitutions: Not permitted.

C. Requests for substitutions will be considered in accordance with provisions of Section 01600.

** NOTE TO SPECIFIER ** Select the shades required from the following paragraphs. For each Draper window shade there are options for size, fabric, operator, operator location, controls, method of installation, hardware, and hardware finish. Refer to Draper product literature for availability of options and selection guidelines. Various options are listed in this specification section, but not all options apply to all window shades. The specifier will need to select the appropriate options, verify their availability, and delete non-applicable models and options.

2.2 MANUALLY OPERATED WINDOW SHADES

12494-4

** NOTE TO SPECIFIER ** Use the following paragraphs to specify manually operated Draper Chain and Clutch Operated FlexShade, Draper Chain and Clutch Operated FlexShade XD, Crank Operated FlexShade and Spring Roller Operated FlexShade. Select type and operation from the following Paragraphs. Delete those not required.

A. Manually Operated Window Shades with Independent Control: Manually operated, vertical roll-up, fabric window shade with components necessary for complete installation; Manual FlexShade as manufactured by Draper, Inc.

** NOTE TO SPECIFIER ** Select Bead Chain and Clutch or Crank operation type for window shade from the following options, delete the one not applicable.

1. Operation: Bead chain and clutch operating mechanism allowing shade to stop when chain is released. Designed never to need adjustment or lubrication. Provide limit stops to prevent shade from being raised or lowered too far.a. Clutch mechanism: Fabricated from high carbon steel and molded fiberglass

reinforced polyester or injected molded nylon. White or Black color as selected by Architect.

** NOTE TO SPECIFIER ** Select stainless steel (standard) or optional plastic bead chain from the following two paragraphs and delete the one not required.

b. Bead chain loop: Stainless steel bead chain hanging at side of window.c. Bead chain loop: Plastic bead chain hanging at side of window, Ivory, Grey,

White, Bronze or Black color as selected by Architect.d. Idler Assembly: Provide roller idler assembly of molded nylon with adjustable or

spring-loaded length idler pin to facilitate easy installation, and removal of shade for service.

e. Bead Chain Hold Down: P-Clip (standard).f. Bead Chain Hold Down: Spring-Loaded Tensioner.

2. Operation: Crank and gear box.** NOTE TO SPECIFIER ** For Crank Operated FlexShade include one of the following two Operation paragraphs and delete the one not required. Delete if not required.

a. Single shade.b. Multiple shades.c. Gear box: Die cast aluminum and steel construction. Injection molded nylon

and steel crank insert installed in roller to engage gear box.d. Crank handle:

** NOTE TO SPECIFIER ** Crank handle can be detachable or permanently mounted, select one of the following paragraphs.

1) Detachable anodized aluminum and chrome plated steel handle.2) Permanently mounted anodized aluminum and chrome plated steel

handle.** NOTE TO SPECIFIER ** Crank handle can be provided in lengths up to 10 feet., select one of the following paragraphs.

3) Size: 4 feet (122 cm).4) Size: 6 feet (183 cm).5) Size: 10 feet (305 cm).

e. Idler Assembly: Provide roller idler assembly of molded nylon with adjustable length idler pin to facilitate easy installation, and removal of shade for service.

3. Roller Tube: Fabricated from extruded aluminum, galvanized steel, or enameled steel. Diameter, wall thickness, and material selected by manufacturer to accommodate shade type and size. Fabric connected to the roller tube with LSE (low surface energy) double sided adhesive specifically developed to attach coated textiles to metal. Adhesive attachment to eliminate horizontal impressions in fabric.

** NOTE TO SPECIFIER ** Two or three Crank Operated FlexShades can be controlled from one crank with FlexShade Coupling System. Shades can be different widths but total group width cannot exceed 20 feet and all rollers must be same diameter. Delete if not required.

12494-5

4. Coupling system: Provide system to operate shades from single crank by coupling shade rollers together. System to consist of endcaps, plus couplings to connect rollers.

** NOTE TO SPECIFIER ** Select number of shades to be operated from single crank from the following.

a. 2 shades operated from single crank.b. 3 shades operated from single crank.c. 4 shades operated from single crank.

5. Shade slat: Slat encased in heat seamed hem.** NOTE TO SPECIFIER ** Select the mounting type required for window shade from the following options, delete those not applicable. If multiple types are required indicate the location of each in the schedule at the end of this section.

6. Mounting:a. Mounting brackets.b. Endcaps only.c. Endcaps and fascia.d. Endcaps and headbox.e. Headbox.f. Ceiling pocket.

** NOTE TO SPECIFIER ** Shades provided without endcaps will require mounting brackets. Brackets are not used with Fascia or Headbox. Delete if not required.

7. Brackets: Plated stamped steel. Provide size compatible with roller size.** NOTE TO SPECIFIER ** Select bracket mounting type required from the following and delete those not applicable. If multiple types are required indicate the location of each in the schedule at the end of this section.

a. Mounted to ceiling.b. Mounted to wall.c. Mounted to jamb.

** NOTE TO SPECIFIER ** Include endcaps if required and delete if not required. Endcaps are required for Crank Operated FlexShades and are optional for Chain and Clutch Operated FlexShades. Endcaps are also required for attachment of fascia and headbox.

8. Endcaps: Stamped steel with universal design suitable for mounting to ceiling, wall, and jamb. Provide size compatible with roller size.a. Endcap covers: To match fascia or headbox color.

** NOTE TO SPECIFIER ** Draper manually operated shades can be provided with aluminum fascia concealing shade roller and hardware. Fascia can be mounted inside window opening extending from jamb to jamb or mounted outside and overlapping window opening. Fascia is attached to endcaps. Fascia can be provided in lengths up to 16 feet and either 3-7/8 or 4-5/8 inches high. Fascia available for reverse roll applications. Include the following paragraph if fascia is required. Delete if not required.

9. Fascia: L shaped aluminum extrusion to conceal shade roller and hardware.a. Attachment: Snaps onto endcaps without requiring exposed fasteners of any

kind. Fascia can be mounted continuously across two or more shade bands. No notching is required.

** NOTE TO SPECIFIER ** Select the shape required from the following two paragraphs and delete the one not required.

b. Shape: Square Fascia Panel.c. Shape: Radius Fascia Panel.

** NOTE TO SPECIFIER ** Select the finish required from the following paragraphs and delete those not required.

d. Finish: Clear anodized.e. Finish: Black powder coat.f. Finish: White powder coat.g. Finish: Ivory powder coat.

12494-6

h. Finish: Bronze powder coat.i. Finish: Custom powder coat as selected by the Architect.

** NOTE TO SPECIFIER ** Draper manually operated shades can be provided with aluminum headbox designed for exposed surface or recessed ceiling installation. Ceiling/Wall style headbox consists of removable closure, back and top, and endcaps. Pocket style headbox consists of removable closure, U-Shaped pocket and endcaps. Headbox is provided in two sizes. Refer to Draper product literature for required sizes based on window and roller size. Include one of the following paragraphs if headbox is required. Delete if not required.

10. Headbox Ceiling/Wall style: Aluminum fabrication with removable closure, endcaps, and back and top cover piece:


a. Finish: Clear anodized.b. Finish: Black powder coat.c. Finish: White powder coat.d. Finish: Ivory powder coat.e. Finish: Bronze powder coat.f. Finish: Custom powder coat as selected by the Architect.

11. Headbox, Pocket style: Aluminum fabrication with removable closure, endcaps, and U-shaped pocket:



** NOTE TO SPECIFIER ** Select one of the following two paragraphs for Shade Pockets or Wall Clip with Closure Panel as required and delete the paragraph not required.** NOTE TO SPECIFIER ** Chain and Clutch Operated FlexShades can be provided with and installed in fabricated pockets. Type D Pockets are designed to be installed prior to or as part of ceiling system installation. Window shade assembly can be site installed later after construction operations that might damage shade are complete. Include the following paragraph if Type D Pockets are required. Delete if not required.

12. Type D Shade pocket: Rectangular pocket and endcaps designed for recessed ceiling installation of window shades.a. Material: Extruded aluminum alloy or steel with white finish.b. Size: 5 inches (127 mm) wide by 5-3/8 inches (137 mm) high.c. Closure Panel:

** NOTE TO SPECIFIER ** Closure panel is optional select the one required or delete if not required.

1) 1-1/2 (38 mm) closure dimension, recommended for bead chain operation.

2) 3 inch (78 mm). If selected for CL or XD installer must notch the closure panel to allow the chain to pass through.

** NOTE TO SPECIFIER ** Endcaps kit with acoustical ceiling panel support lip is optional. Select if required or delete if not required.

d. Pocket End Cap Kit: Metal endcaps with 7/8 inch (22 mm) lip for support of acoustical ceiling panel.

** NOTE TO SPECIFIER ** Type D FlexShade Pocket can be provided with corner sections where window shade recess continues around two walls. Pocket ends can also be provided. Choose all that apply.

e. Corners: Welded one-piece aluminum sections connecting to and matching

12494-7

pockets to allow continuous shade recess at ceiling corners.** NOTE TO SPECIFIER ** Draper manually operated window shades can be installed in a ceiling recess site constructed from light gage metal framing and gypsum board or other materials. For this condition, use the following paragraph to specify aluminum removable closure panel to be installed leaving a minimal slot for passage of shade. Delete if not required.

13. Wall Clip with Closure Panel: For site constructed ceiling recesses, provide removable closure panel to minimize slot for shade passage but allowing access to shade for maintenance.a. Material: Aluminum alloy with white epoxy paint finish.

** NOTE TO SPECIFIER ** Delete the following paragraph if tile lip option is not required.b. Tile Lip: Provide wall clip with 7/8 inch tile lip (22 mm).

** NOTE TO SPECIFIER ** Select closure width required from the following paragraphs.c. Closure width: 1-1/2 inches (38 mm).d. Closure width: 3 inches (76 mm).e. Closure Width: 5 inches (127 mm).f. Provide continuous wall clip, 1-3/4 (44 mm) by 3/16 inch (5 mm), for snap-in

attachment of closure panel without fasteners.14. Light Gap Reduction Channels.

** NOTE TO SPECIFIER ** Select channel size required from the following paragraphs.a. L Angle - 3/4 inch (19 mm) by 1 inch (25 mm).b. L Angle -1 inch (25 mm) by 2-3/4 inches (70mm).c. U Channel -1 inch (25 mm) by 2-1/2 inches (64 mm).d. H Channel - 1 inch (25 mm) by 5 inches (127 mm).

B. Manually Operated Window Shades with Independent Control: Manually operated, vertical roll-up, fabric window shade with components necessary for complete installation; Manual FlexShade XD as manufactured by Draper, Inc.1. Operation: Bead chain and clutch operating mechanism allowing shade to stop when

chain is released. Designed never to need adjustment or lubrication. Provide limit stops to prevent shade from being raised or lowered too far.a. Clutch mechanism: Fabricated from POM thermoplastic with welded 0.354 inch

(9 mm) primary steel post with rotational bearing, overrunning design, and positive mechanical engagement of drive mechanism to tube. White or Black color as selected by Architect. Center bead chain placement for right or left hand operation and accommodates side channel with no adjustment of chain location.

** NOTE TO SPECIFIER ** Select stainless steel or optional plastic bead chain from the following two paragraphs and delete the one not required.

b. Bead chain loop: Stainless steel bead chain.c. Bead chain loop: Polyester bead chain, Ivory, Grey, White, Bronze or Black

color as selected by Architect.** NOTE TO SPECIFIER ** Select Bead Chain Hold Down required from the following paragraphs.

d. Bead Chain Hold Down: P-Clip.e. Bead Chain Hold Down: Spring-Loaded Tensioner.

2. Rollers: Extruded aluminum roller tube of appropriate diameter to support shade fabric with minimal deflection.a. Minimum Roller Tube Diameter: 1.56 inches (40 mm).b. Fabric Connection to Roller Tube: Spline fabric/roller attachment system to

allow shade fabric to be removed from roller without having to remove roller from brackets.

c. Fabric Length: 6 inches (152 mm) greater than window height minimum.d. Bottom Slat: 13/16 inch (20.6 mm) aluminum dowel, encased in bottom hem

with heat sealed ends.** NOTE TO SPECIFIER ** Select orientation required from the following paragraphs.

12494-8

e. Orientation: Regular from back of roller.f. Orientation: Reverse from front of roller.

** NOTE TO SPECIFIER ** Select the mounting type required for window shade from the following options, delete those not applicable. If multiple types are required indicate the location of each in the schedule at the end of this section.

3. Mounting:a. Endcaps only.b. Endcaps and fascia.c. Endcaps and headbox.d. Headbox.e. Ceiling pocket.


** NOTE TO SPECIFIER ** Select endcap mounting type required from the following and delete those not applicable. If multiple types are required indicate the location of each in the schedule at the end of this section.

b. Mounted to ceiling.c. Mounted to wall.d. Mounted to jamb.

** NOTE TO SPECIFIER ** Draper XD manually operated shades can be provided with aluminum fascia concealing shade roller and hardware. Fascia can be mounted inside window opening extending from jamb to jamb or mounted outside and overlapping window opening. Fascia is attached to endcaps. Fascia can be provided in lengths up to 16 feet and either 3-7/8 or 4-5/8 inches high. Fascia available for reverse roll applications. Include the following paragraph if fascia is required. Delete if not required.






d. Finish: Clear anodized.e. Finish: Black powder coat.f. Finish: White powder coat.g. Finish: Ivory powder coat.h. Finish: Bronze powder coat.i. Finish: Custom powder coat as selected by the Architect.

** NOTE TO SPECIFIER ** Draper XD manually operated shades can be provided with aluminum headbox designed for exposed surface or recessed ceiling installation. Ceiling/Wall style headbox consists of removable closure, back and top, and endcaps. Pocket style headbox consists of removable closure, U-Shaped pocket and endcaps. Headbox is provided in two sizes. Refer to Draper product literature for required sizes based on window and roller size. Include one of the following paragraphs if headbox is required. Delete if not required.

6. Headbox Ceiling/Wall style: Aluminum fabrication with removable closure, endcaps, and back and top cover piece:


a. Finish: Clear anodized.b. Finish: Black powder coat.

12494-9

c. Finish: White powder coat.d. Finish: Ivory powder coat.e. Finish: Bronze powder coat.f. Finish: Custom powder coat as selected by the Architect.

7. Headbox, Pocket style: Aluminum fabrication with removable closure, endcaps, and U-shaped pocket:



** NOTE TO SPECIFIER ** Select one of the following two paragraphs for Shade Pockets or Wall Clip with Closure Panel as required and delete the paragraph not required.** NOTE TO SPECIFIER ** Chain and Clutch Operated FlexShades can be provided with and installed in fabricated pockets. Type D Pockets are designed to be installed prior to or as part of ceiling system installation. Window shade assembly can be site installed later after construction operations that might damage shade are complete. Include the following paragraph if Type D Pockets are required. Delete if not required.

8. Type D Shade pocket: Rectangular pocket and endcaps designed for recessed ceiling installation of window shades.a. Material: Extruded aluminum alloy or steel with white finish.b. Size: 5 inches (127 mm) wide by 5-3/8 inches (137 mm) high.c. Closure Panel:


1) 1-1/2 (38 mm) closure dimension, recommended for bead chain operation.

2) 3 inch (78 mm). If selected for CL or XD installer must notch the closure panel to allow the chain to pass through.

** NOTE TO SPECIFIER ** Endcaps with acoustical ceiling panel support lip is optional. Select if required or delete if not required.

d. Pocket Endcap Kit: Metal endcaps with 7/8 inch (22 mm) lip for support of acoustical ceiling panel.


e. Corners: Welded one-piece aluminum sections connecting to and matching pockets to allow continuous shade recess at ceiling corners.

** NOTE TO SPECIFIER ** Draper manually operated window shades can be installed in a ceiling recess site constructed from light gage metal framing and gypsum board or other materials. For this condition, use the following paragraph to specify aluminum removable closure panel to be installed leaving a minimal slot for passage of shade. Delete if not required.

9. Wall Clip with Closure panel: For site constructed ceiling recesses, provide removable closure panel to minimize slot for shade passage but allowing access to shade for maintenance.a. Material: Aluminum alloy with white epoxy paint finish.


** NOTE TO SPECIFIER ** Select closure width required from the following paragraphs.c. Closure width: 1-1/2 inches (38 mm).d. Closure width: 3 inches (75 mm).

12494-10

e. Closure Width: 5 inches (127 mm).f. Provide continuous wall clip, 1-3/4 (44 mm) by 3/16 inch (5 mm), for snap-in

attachment of closure panel without fasteners.10. Light Gap Reduction Channels.

** NOTE TO SPECIFIER ** Select channel size required from the following paragraphs.a. L Angle - 3/4 inch (19 mm) by 1 inch (25 mm).b. L Angle -1 inch (25 mm) by 2-3/4 inches (70mm).c. U Channel -1 inch (25 mm) by 2-1/2 inches (64 mm).d. H Channel - 1 inch (25 mm) by 5 inches (127 mm).

C. Manually Operated Spring Roller Shade: Manually operated, vertical roll-up, fabric window shade with components necessary for complete installation; Spring Roller Shades as manufactured by Draper, Inc.1. Operation: Spring roller operating mechanism with metal roller containing heavy duty

spring with positive locking mechanism permitting shade to be stopped at each half turn of roller. Provide cord clasp and braided cotton cord attached to bottom shade slat. Spring sized by manufacturer to accommodate shade size. Provide roller idler assembly of molded nylon and zinc-plated steel pin.

2. Roller Tube: Fabricated from extruded aluminum, galvanized steel, or enameled steel. Diameter, wall thickness, and material selected by manufacturer to accommodate shade type and size. Fabric connected to the roller tube with LSE (low surface energy) double sided adhesive specifically developed to attach coated textiles to metal. Adhesive attachment to eliminate horizontal impressions in fabric.

3. Shade slat: Slat encased in heat seamed hem.** NOTE TO SPECIFIER ** Select the mounting type required for window shade from the following options, delete those not applicable. If multiple types are required indicate the location of each in the schedule at the end of this section.

4. Mountinga. Mounting brackets.b. Endcaps and fascia.c. Endcaps and headbox.

** NOTE TO SPECIFIER ** Shades provided without endcaps will require mounting brackets. Delete if not required.

5. Brackets: Plated stamped steel. Provide size compatible with roller size.** NOTE TO SPECIFIER ** Select bracket mounting type required from the following and delete those not applicable. Brackets are not used with Fascia or Headbox. If multiple types are required indicate the location of each in the schedule at the end of this section.

a. Mounted to ceiling.b. Mounted to wall.c. Mounted to jamb.

** NOTE TO SPECIFIER ** Include endcaps if required and delete if not required. Endcaps are optional for Spring Roller Operated FlexShades. Endcaps are also required for attachment of fascia and headbox.


** NOTE TO SPECIFIER ** Draper manually operated shades can be provided with aluminum fascia concealing shade roller and hardware. Fascia can be mounted inside window opening extending from jamb to jamb or mounted outside and overlapping window opening. Fascia is attached to endcaps. Fascia can be provided in lengths up to 16 feet and either 3-7/8 or 4-5/8 inches high. Fascia available for reverse roll applications. Include the following paragraph if fascia is required. Delete if not required.


12494-11





d. Finish: Clear anodized.e. Finish: Black powder coat.f. Finish: White powder coat.g. Finish: Ivory powder coat.h. Finish: Bronze powder coat.i. Finish: Custom powder coat as selected by the Architect.

** NOTE TO SPECIFIER ** Draper manually operated shades can be provided with aluminum headbox designed for exposed surface or recessed ceiling installation. Headbox consists of removable closure, back and top, and endcaps. Headbox is provided in two sizes. Refer to Draper product literature for required sizes based on window and roller size. Include the following paragraphs if headbox is required. Delete if not required.

8. Headbox: Aluminum fabrication with removable closure, endcaps, and back and top cover piece:



** NOTE TO SPECIFIER ** Use the following paragraphs to specify Draper Motorized FlexShades. Select the motor and control types desired from the following paragraphs. Delete if not required.

2.3 MOTORIZED WINDOW SHADES

A. Type: Motorized vertical roll-up, fabric, window shade with motors, controls, mounting brackets, and other components necessary for complete installation; Motorized FlexShade as manufactured by Draper, Inc.

** NOTE TO SPECIFIER ** Select the mounting type required for window shade from the following options, delete those not applicable. Brackets are not used with Headbox. If multiple types are required indicate the location of each in the schedule at the end of this section.

1. Mounting brackets.2. Endcaps and fascia.3. Endcaps and headbox.4. Ceiling pocket.

B. Shade Motor and Control System** NOTE TO SPECIFIER ** Select one of the following motor option paragraphs and delete the ones not required. General descriptions of each Motor and Control system are included with each option below. Contact Draper for more information concerning motor limitations.** NOTE TO SPECIFIER ** Standard Motor: 115V AC tubular motor with 4-wire pigtail. All controls and receivers will be external to the motor. Can be tied into building systems using optional external control interfaces. Only those controls listed in this section will operate this motor.

1. Standard Motor: 110 VAC, single phase, 60 HZ, instantly reversible, lifetime lubricated, and equipped with internal thermal overload protector, electric brake, and

12494-12

pre-set accessible limit switches. Tubular motor concealed inside each shade roller tube.

** NOTE TO SPECIFIER ** Select one of the following control option paragraphs and delete the ones not required. For each control selected select the control device(s) required and delete those not required.

a. Individual Control:1) Wall Switch - Toggle three position wall switch.2) Wall Switch - Key operated three position wall switch.3) SC1 - ETL component allows 1 motor to operate on any input in any

grouping. Up to 4 programmable mid-window alignments from a wall switch for a total of 6 stops with full up and down. No DIP switches required. Controlled via low voltage input.

b. Group Control:1) ISO relay - ETL component. One ISO relay per motor. Allows 110-120V

group switching via toggle switch. Allows for up to 12 motors on one switch.

2) GC4 - ETL assembly. Panelized version with four ISO relays. Up to three GC4s can be linked together for control of up to 12 motors from any single 15 amp double throw wall switch.

3) SGC1- ETL component allows 1 motor to operate on any input in any grouping. No DIP switches required. Controlled via low voltage input.

4) SGC4 - ETL assembly. Panelized version with 4 ISO relays and low voltage control inputs. Multiple SGC4s can be linked together to form larger groups. Fully programmable. No dip switches required.

c. Individual and Group Control:1) SC1 - ETL component allows 1 motor to operate on any input in any



3) SPGC4 - ETL assembly. Panelized version of four SC1s. Up to 4 programmable mid-window alignments from switch for a total of 6 stops with full up and down. Fully programmable. No DIP switches required. Controlled via low voltage input.

** NOTE TO SPECIFIER ** Note that the IP interface requires a connection the building server to pull time data and an IP address for access to the interface.

d. IP Interface: Interface for virtual switch, timed events, and priority events to be input on DDN.

** NOTE TO SPECIFIER ** Select one of the following low voltage input option paragraphs whenever an SC-1 Group or Individual Control is specified above. Delete if not required. If multiple types are required indicate the location of each in the schedule at the end of this section.

e. Low Voltage Inputs:1) Intelliflex Wall Switches - Appropriate low voltage switch to provide

control via b programmable dry contacts.2) IR Remote Control.3) RF Remote Control.4) Sun Sensor/Timer - Allows one group per sensor to automatically move

up and down at programmed sun levels and/or times.5) RS 232/485 - Allows full control of shades via RS-232/485 output

provided by others.** NOTE TO SPECIFIER ** Quiet Standard Motor: Motor operates at 44 Db. Motor noise is approximately 30 percent less than standard tubular motors. All controls and receivers will be external to the motor. Can be tied into building systems using optional external control interfaces. Only those controls listed will operate this motor.

12494-13

2. Quiet Standard Motor - 110 VAC motor operates at 44 Db measured 3 feet from the motor. Makes no audible clicks when motor stops or starts. Tubular motor concealed inside each shade roller tube.


a. Individual Control:1) Wall Switch - Toggle three position wall switch.2) Wall Switch - Key operated three position wall switch.3) SC1 - ETL component allows 1 motor to operate on any input in any


b. Group Control:1) ISO relay - ETL component. One ISO relay per motor. Allows 110-120V

group switching via toggle switch. Allows for up to 12 motors on one switch.

2) GC4 - ETL assembly. Panelized version with four ISO relays. Up to three GC4s can be linked together for control of up to 12 motors from any single 15 amp double throw wall switch.


4) SGC4 - ETL assembly. Panelized version with 4 ISO relays and low voltage control inputs. Multiple SGC4s can be linked together to form larger groups. Fully programmable. No dip switches required.

c. Individual and Group Control:1) SC1 - ETL component allows 1 motor to operate on any input in any



3) SPGC4 - ETL assembly. Panelized version of four SC1s. Up to 4 programmable mid-window alignments from switch for a total of 6 stops with full up and down. Fully programmable. No DIP switches required. Controlled via low voltage input.


d. IP Interface: Interface for virtual switch, timed events, and priority events to be input on DDN.

** NOTE TO SPECIFIER ** Select one of the following low voltage input option paragraphs whenever an SC-1 Group or Individual Control is specified above. Delete if not required. If multiple types are required indicate the location of each in the schedule at the end of this section.

e. Low Voltage Inputs:1) Intelliflex Wall Switches - Appropriate low voltage switch to provide

control via b programmable dry contacts.2) IR Remote Control.3) RF Remote Control.4) Sun Sensor/Timer - Allows one group per sensor to automatically move

up and down at programmed sun levels and/or times.5) RS 232/485 - Allows full control of shades via RS-232/485 output

provided by others.** NOTE TO SPECIFIER ** Battery Motor: Battery powered motor with 12V Battery Pack and built-in radio receiver. No wiring required. Only those controls listed will operate this motor.

3. Battery Motor with 12V Battery Pack - Battery powered motor with built-in radio

12494-14

receiver. Includes 12V battery pack. No external wiring required. Tubular motor concealed inside each shade roller tube.

** NOTE TO SPECIFIER ** Select the Battery Wand required and delete those not required.a. Battery Wand:

1) Battery Wand.2) Reloadable Battery Wand (AAA lithium batteries not included).3) NiMH Solar Rechargeable Battery Wand with Solar Recharge Panel.

** NOTE TO SPECIFIER ** Select the control device(s) required and delete those not required.b. Individual Control, Group Control and Individual and Group Control:

1) Single channel wireless handheld transmitter-White.2) Single channel wireless handheld transmitter-Black.3) Four channel wireless handheld transmitter-White.4) Four channel wireless handheld transmitter-Black.5) 16-Channel wireless handheld transmitter-White.6) 16-Channel wireless handheld transmitter-Silver.7) Single channel wireless wall switch for radio motor control-White.8) Single channel wireless wall switch for radio motor control-Ivory.9) Four channel wireless wall switch for radio motor control-White.10) Four channel wireless wall switch for radio motor control-Ivory.11) RS-232/Dry Contact - Allows for full control of radio motor shade via RS-

232/dry contact interface.12) Wireless Sun Sensor - Allows operation of one group of radio motors per

sensor.13) Wireless Timer - Allows operation of one group of radio motors per timer.14) Repeater (1 per project to extend range of transmitters)15) (URTSI II) Universal Interface - Allows for full control of radio motor

shade via RS-232/485 or IR signals.** NOTE TO SPECIFIER ** Radio Technology Motor: Motor with built-in radio receiver. 3-wire pigtail allows for attachment of optional three prong plug for plug-an-play operation. Can be tied into building systems using optional external control interfaces. Only those controls listed will operate this motor.

4. Radio Technology Motor- 110 VAC motor with built-in radio receiver. Tubular motor concealed inside each shade roller tube.

** NOTE TO SPECIFIER ** Select the control device(s) required and delete those not required.a. Individual Control, Group Control and Individual and Group Control:



sensor.13) Wireless Timer - Allows operation of one group of radio motors per timer.14) Repeater, 1 per project to extend range of transmitters.15) (URTSI II) Universal Interface - Allows for full control of radio motor

shade via RS-232/485 or IR signals.** NOTE TO SPECIFIER ** Quiet Radio Technology Motor: Quiet motor with built-in radio receiver. Operates at 44 Db. Motor noise is approximately 30 percent less than standard tubular motor. Can

12494-15

be tied into building systems using optional external control interfaces. Only those controls listed will operate this motor.

5. Quiet Radio Technology Motor- 110 VAC quiet motor with built-in radio receiver. Tubular motor concealed inside each shade roller tube.




sensor.13) Wireless Timer - Allows operation of one group of radio motors per timer.14) Repeater, 1 per project to extend range of transmitters.15) (URTSI II) Universal Interface - Allows for full control of radio motor

shade via RS-232/485 or IR signals.** NOTE TO SPECIFIER ** 24V DC Quiet Motor: 24V DC Quiet motor with built-in radio receiver. Operates at 44 DB. Requires 24V transformer. Low voltage wiring does not require an electrician. Can be tied into building systems using optional external control interfaces. Only those controls listed will operate this motor.

6. 24V DC Quiet Motor - 24V DC quiet motor with built-in radio receiver. Tubular motor concealed inside each shade roller tube.




sensor.13) Wireless Timer - Allows operation of one group of radio motors per timer.14) Repeater,1 per project to extend range of transmitters15) (URTSI II) Universal Interface - Allows for full control of radio motor

shade via RS-232/485 or IR signals.** NOTE TO SPECIFIER ** Note that the IP interface requires a connection the building server to pull time data and an IP address for access to the interface.

b. IP Interface: Interface for virtual switch, timed events, and priority events to be input on DDN.

c. Transformer (24V DC ONLY):

12494-16

** NOTE TO SPECIFIER ** Select the transformer type and motor quantity required and delete those not required.

1) Plug-In:a) 1 Motor - Wall Type.b) 1 Motor - Floor Type.

2) Power Panel:a) 5 Motors.b) 10 Motors.c) 15 Motors.d) 20 Motors.

** NOTE TO SPECIFIER ** Intelligent Technology Motor: Motor with built-in low voltage controller with 3-wire pigtail and data cable. No external motor control interface required. Best for integration into building automation systems. Available with optional three prong plug for plug-and-play operation. Only those controls listed will operate this motor.

7. Intelligent Technology Motor - 110 VAC motor with built-in low voltage controller with 3-wire pig tail and data cable. No external motor controls are required. Available with optional three prong plug. Tubular motor concealed inside each shade roller tube.

** NOTE TO SPECIFIER ** Select the control device(s) required and delete those not required.a. Individual Control, Group Control & Individual and Group Control:

1) 3 Button RS 485 switch- for up/stop/down control of a group.2) 6 button RS 485 switch- for 2 groups up/stop/down or 1 group

up/stop/down and 3 presets.3) 32 point BACnet interface- Control of up to 32 groups with feedback via

BACnet over IP.4) Draper Digital Newtork. DDN system of window shades with intelligent

motors linked to an IP interface box and potentially other input devices such as hospital bed controls, wall switches and sun sensors.

** NOTE TO SPECIFIER ** Note that the IP interface requires a connection to the building server to pull time data and an IP address for access to the interface

b. IP Interface: Interface for virtual switch, timed events, and priority events. Requires input on DDN.

** NOTE TO SPECIFIER ** Quiet Intelligent Technology Motor: Motor with built-in low voltage controller with 3-wire pigtail and data cable. Operates at 44 Db. No external motor control interface required. Best for integration into building automation systems. Available with optional three prong plug for plug-and-play operation. Only those controls listed will operate this motor.

8. Quiet Intelligent Technology Motor - 110 VAC quiet motor with built-in low voltage controller with 3-wire pig tail and data cable. Motor operates at 44 Db measured 3 feet from the motor. Makes no audible clicks when motor stops or starts. Available with optional three prong plug. Tubular motor concealed inside each shade roller tube.






** NOTE TO SPECIFIER ** Note that the IP interface requires a connection to the building server to pull time data and an IP address for access to the interface

b. IP Interface: Interface for virtual switch, timed events, and priority events. Requires input on DDN.

** NOTE TO SPECIFIER ** 24V DC RS 485 Motor: 24V DC Quiet motor with built-in intelligence for

12494-17

RS 485 control. Operates at 44 DB. Requires 24V transformer. Low voltage wiring does not require an electrician. Can be tied into building systems using optional external control interfaces. Only those controls listed will operate this motor.

9. 24V DC RS 485 Motor - 24V DC quiet motor with built-in intelligence for RS 485 control.Tubular motor concealed inside each shade roller tube.







b. IP Interface: Interface for virtual switch, timed events, and priority events to be input on DDN.

c. Transformer (24V DC ONLY):** NOTE TO SPECIFIER ** Select the transformer type and motor quantity required and delete those not required.

1) Plug-In:a) 1 Motor - Wall Type.b) 1 Motor - Floor Type.

2) Power Panel:a) 5 Motors.b) 10 Motors.c) 15 Motors.d) 20 Motors.

C. Roller: Fabricated from extruded aluminum or steel. Diameter, wall thickness, and material selected by manufacturer to accommodate shade size. Provide with roller idler assembly of molded nylon and zinc-plated steel pin. Sliding pin to allow easy installation and removal of roller. Fabric connected to the roller tube with LSE (low surface energy) double sided adhesive specifically developed to attach coated textiles to metal. Adhesive attachment to eliminate horizontal impressions in fabric.

** NOTE TO SPECIFIER ** Endcaps are required for attachment of fascia or use with headbox. Delete if not required.

D. Endcaps: Stamped steel with universal design suitable for mounting to ceiling, wall, and jamb. Provide size compatible with roller size.

** NOTE TO SPECIFIER ** Endcaps can be provided with snap-on covers to match hardware finish. Delete if not required.

E. Endcap covers to match fascia/headbox finish.** NOTE TO SPECIFIER ** Shades provided without endcaps will require mounting brackets. Delete if not required.

F. Brackets: 1/8 inch thick stamped steel, black powder coat, idler height adjuster, field adjustable to wall or ceiling mount.

** NOTE TO SPECIFIER ** Select bracket mounting type required from the following and delete those not applicable. If multiple types are required indicate the location of each in the schedule at the end of this section.

12494-18

1. Mounted to ceiling.2. Mounted to wall.3. Mounted to jamb.

** NOTE TO SPECIFIER ** Up to five Draper Motorized FlexShades can be operated by a single motor by coupling the rollers with Draper FlexShade Coupling System. Shades can be different widths (up to 120 inches (305 cm) per panel) but all rollers must be the same diameter. Maximum group width is 30 feet (9.1 m). System consists of male and female couplings and wall or ceiling brackets. Motor can be installed in either the far left or far right shades, with no more than five panels on one motor. Delete if not required.

G. Coupling system: Couplings to join motorized shade rollers to allow operation by single motor. FlexShade Coupling System as manufactured by Draper, Inc. Provide endcaps to receive couplers and support multiple shades.

H. Shade slat: Slat encased in heat-seamed hem.** NOTE TO SPECIFIER ** Draper Motorized FlexShades can be provided with aluminum fascia concealing shade roller and hardware. Fascia can be mounted inside window opening extending from jamb to jamb or mounted outside and overlapping window opening. Fascia is attached to endcaps. Fascia can be provided in lengths up to 16 feet and either 3-7/8 or 4-5/8 inches high. Fascia available for reverse roll applications. If fascia is required, include the following paragraph. Delete if not required.

I. Fascia: L shaped aluminum extrusion to conceal shade roller and hardware.1. Attachment: Snaps onto end caps without requiring exposed fasteners of any kind.

Fascia can be mounted continuously across two or more shade bands.** NOTE TO SPECIFIER ** Select the shape required from the following two paragraphs and delete the one not required.

a. Shape: Square Fascia Panel.b. Shape: Radius Fascia Panel.


2. Finish: Clear anodized.3. Finish: Black powder coat.4. Finish: White powder coat.5. Finish: Ivory powder coat.6. Finish: Bronze powder coat.7. Finish: Custom powder coat as selected by the Architect.

** NOTE TO SPECIFIER ** Draper Motorized FlexShades can be provided with aluminum headbox designed for exposed surface or recessed ceiling installation. Ceiling/Wall style headbox consists of removable closure, back and top, and endcaps. Pocket style headbox consists of removable closure, U-shaped pocket and endcaps. Headbox is provided in two sizes. Refer to Draper product literature for required sizes based on window and roller size. If headbox is required, include one of the following paragraphs. Delete if not required.

J. Headbox Ceiling/Wall Style: Aluminum fabrication with removable closure, endcaps, and back and top cover piece:



12494-19

K. Headbox, Pocket Style: Aluminum fabrication with removable closure, endcaps, and U-shaped pocket:



** NOTE TO SPECIFIER ** Select one of the following two paragraphs for Shade Pockets or Wall Clip with Closure Panel as required and delete the paragraph not required.** NOTE TO SPECIFIER ** Motorized FlexShades can be provided with and installed in fabricated pockets. Pockets are designed to be installed prior to or as part of ceiling system installation. Window shade assembly can be site installed later after construction operations that might damage shade are complete. Include the following paragraph if aluminum pockets are required. Delete if not required.

L. Type D Shade pocket: Rectangular pocket designed for recessed ceiling installation of window shades.1. Material: Extruded aluminum alloy with white epoxy paint finish.2. Size: 5 inches (127 mm) by 5-5/8 inches (137 mm) high.3. Closure Panel:


a. 1-1/2 (38 mm) closure dimension, recommended for bead chain operation.b. 3 inch (78 mm). If selected for CL or XD installer must notch the closure panel

to allow the chain to pass through.** NOTE TO SPECIFIER ** Endcaps for Type D FlexShade Pocket is provided with an acoustical ceiling panel support lip.

4. Pocket Endcap Kit: Endcaps with 7/8 inch (22 mm) lip for support of acoustical ceiling panel.


5. Corners: Welded one-piece aluminum sections connecting to and matching pockets to allow continuous shade recess at ceiling corners.

6. Pocket ends: Welded one-piece aluminum sections connecting to and matching pockets.

** NOTE TO SPECIFIER ** Draper Motorized FlexShades can be installed in ceiling recess site constructed from light gauge metal framing and gypsum board or other materials. For this condition, use the following paragraph and subparagraphs to specify aluminum removable closure panel to be installed leaving a minimal slot for passage of shade. Delete if not required.

7. Wall Clip with Closure panel: For site constructed ceiling recesses, provide removable closure panel to minimize slot for shade passage but allowing access to shade for maintenance.a. Material: Aluminum alloy with white epoxy paint finish.


** NOTE TO SPECIFIER ** Select closure width required from the following paragraphs.c. Closure width: 1-1/2 inches (38 mm).d. Closure width: 3 inches (75 mm).e. Closure Width: 5 inches (127 mm).f. Provide continuous wall clip, 1-3/4 (44 mm) by 3/16 inch (5 mm), for snap-in

12494-20

attachment of closure panel without fasteners.** NOTE TO SPECIFIER ** Draper Motorized FlexShades can be installed with light reduction channels. For this requirement, use the following paragraph and subparagraphs. Delete if not required.

M. Light Gap Reduction Channels** NOTE TO SPECIFIER ** Select channel required from the following.

1. L Angle - 3/4 inch by 1 inch (19 mm by 25 mm).2. L Angle - 1 inch by 2-3/4 inches (25 mm by 70 mm).3. U Channel - 1 inch by 2-1/2 inches (25 mm by 64 mm).4. H Channel - 1 inch (25 mm) by 5 inches (127 mm).

2.4 OPAQUE WINDOW SHADE SYSTEM** NOTE TO SPECIFIER ** Draper LightBloc FlexShade System can be manually or motor operated. Manual shades are provided in three operating styles: chain and clutch, crank, and spring roller. Refer to Draper product literature for selection guidelines. Select operation type from the following. Delete those not required.

A. Operation Type: Motorized, vertical roll-up, fabric, opaque window shade system, complete with headbox, side and sill channels for total opacity; LightBloc FlexShade System as manufactured by Draper, Inc.

B. Operation Type: Bead chain and clutch operated, vertical roll-up, fabric, opaque window shade system, complete with headbox, side and sill channels for total opacity; LightBloc FlexShade System as manufactured by Draper, Inc.

C. Operation Type: Crank operated, vertical roll-up, fabric, opaque window shade system, complete with headbox, side and sill channels for total opacity; LightBloc FlexShade System as manufactured by Draper, Inc.

D. Operation Type: Spring roller operated, vertical roll-up, fabric, opaque window shade system, complete with headbox, side and sill channels for total opacity; LightBloc FlexShade System as manufactured by Draper, Inc.

** NOTE TO SPECIFIER ** For Chain and Clutch Operated LightBloc FlexShade System include the following paragraph. Delete if not required

E. Operation: Bead chain and clutch operating mechanism allowing shade to stop when chain is released. Designed never to need adjustment or lubrication. Provide limit stops to prevent shade from being raised or lowered too far.1. Clutch mechanism: Fabricated from high carbon steel and molded fiberglass

reinforced polyester.** NOTE TO SPECIFIER ** Select stainless steel or plastic bead chain from the following. Delete the one not required.

2. Bead chain loop: Stainless steel bead chain hanging at side of window.3. Bead chain loop: Plastic bead chain hanging at side of window, Ivory, Grey, or Black

color as selected by Architect.4. Idler Assembly: Provide roller idler assembly of molded nylon with adjustable length

idler pin to facilitate easy installation, and removal of shade for service.** NOTE TO SPECIFIER **For Crank Operated LightBloc FlexShade System include the following paragraph. Delete if not required.

F. Operation: Crank and gear box operated shades.1. Gear box: Die cast aluminum and steel construction. Injection molded nylon and steel

crank insert installed in roller to engage gear box.2. Crank handle:

12494-21

** NOTE TO SPECIFIER ** Crank handle can be detachable or permanently mounted, select one of the following paragraphs.

a. Detachable anodized aluminum and chrome plated steel handle.b. Permanently mounted anodized aluminum and chrome plated steel handle.

** NOTE TO SPECIFIER ** Crank handle can be provided in lengths up to 10 feet., select one of the following paragraphs.

c. Size: 4 feet (122 cm).d. Size: 6 feet (183 cm).e. Size: 10 feet (305 cm).

3. Idler assembly: Provide roller idler assembly of molded nylon with adjustable length idler pin or spring-loaded idler to facilitate easy installation, and removal of shade for service.

** NOTE TO SPECIFIER **For Spring Roller Operated LightBloc FlexShade include the following paragraph. Delete if not required.

G. Operation: Metal roller containing heavy-duty spring with positive locking mechanism permitting shade to be stopped at each half turn of the roller. Spring sized by manufacturer to accommodate shade size. Provide pull and latching chain attached to bottom shade slat and catch attached to sill channel. Chain inserted in catch to keep roller under constant tension. Provide roller idler assembly of molded nylon with zinc-plated steel pin.

** NOTE TO SPECIFIER ** For Motorized LightBloc FlexShade System include and edit the following paragraphs as required. Delete if not required.

H. Shade Motor and Control System:** NOTE TO SPECIFIER ** Select one of the following motor option paragraphs and delete the ones not required. Contact Draper for more information concerning motor limitations.

1. Standard Motor: 110 VAC, single phase, 60 HZ, instantly reversible, lifetime lubricated, and equipped with internal thermal overload protector, electric brake, and pre-set accessible limit switches. Tubular motor concealed inside each shade roller tube.


a. Individual Control:1) Wall Switch - Toggle three position wall switch.2) Wall Switch - Key operated three position wall switch.3) SC1 - UL listed component allows 1 motor to operate on up to 7 different

channels. Up to 4 mid-window alignments are programmable for a total of 6 stops with full up and down. Fully programmable. No DIP switches required. Controlled via low voltage input.

b. Group Control:1) ISO relay - UL listed component. One ISO relay per motor. Allows 110-

120V group switching via toggle switch. Allows for up to 12 motors on one switch.

2) GC4 - UL listed assembly. Panelized version with four ISO relays. Up to three GC4s can be linked together for control of up to 12 motors from any single 15 amp double throw wall switch. Fully programmable.

3) SGC4 - UL listed assembly. Panelized version with 4 ISO relays and low voltage control inputs. Multiple SGC4s can be linked together to form larger groups. Fully programmable. No dip switches required.

c. Individual and Group Control:1) SC1 - UL listed component allows 1 motor to operate on up to 7 different


12494-22

2) SPGC4 - UL listed assembly. Panelized version of four SC1s. Allows each motor to operate on up to 7 different channels. Up to 4 mid-window alignments are programmable for a total of 6 stops with full up and down. Fully programmable. No DIP switches required. Controlled via low voltage input.

2. Quiet Standard Motor - 110 VAC motor operates at 44 Db measured 3 feet from the motor. Makes no audible clicks when motor stops or starts. Tubular motor concealed inside each shade roller tube.


a. Individual Control:1) Wall Switch - Toggle three position wall switch.2) Wall Switch - Key operated three position wall switch.3) SC1 - UL listed component allows 1 motor to operate on up to 7 different


b. Group Control:1) ISO relay - UL listed component. One ISO relay per motor. Allows 110-

120V group switching via toggle switch. Allows for up to 12 motors on one switch.

2) GC4 - UL listed assembly. Panelized version with four ISO relays. Up to three GC4s can be linked together for control of up to 12 motors from any single 15 amp double throw wall switch. Fully programmable.

3) SGC4 - UL listed assembly. Panelized version with 4 ISO relays and low voltage control inputs. Multiple SGC4s can be linked together to form larger groups. Fully programmable. No dip switches required.

c. Individual and Group Control:1) SC1 - UL listed component allows 1 motor to operate on up to 7 different


2) SPGC4 - UL listed assembly. Panelized version of four SC1s. Allows each motor to operate on up to 7 different channels. Up to 4 mid-window alignments are programmable for a total of 6 stops with full up and down. Fully programmable. No DIP switches required. Controlled via low voltage input.

3. Radio Technology Motor- 110 VAC motor with built-in radio receiver. Tubular motor concealed inside each shade roller tube.


1) Single channel wireless handheld transmitter.2) Four channel wireless handheld transmitter.3) 16-Channel wireless handheld transmitter.4) Single channel wireless wall switch for radio motor control.5) Four channel wireless wall switch for radio motor control.6) RS-232/Dry Contact - Allows for full control of radio motor shade via RS-


sensor.8) Wireless Timer - Allows operation of one group of radio motors per

timer.9) Multi-Link RS232 to RTS Interface (16-channel).

4. Quiet Radio Technology Motor- 110 VAC quiet motor with built-in radio receiver.

12494-23

Tubular motor concealed inside each shade roller tube.** NOTE TO SPECIFIER ** Select the control device(s) required and delete those not required.

a. Individual Control, Group Control and Individual and Group Control:1) Single channel wireless handheld transmitter.2) Four channel wireless handheld transmitter.3) 16-Channel wireless handheld transmitter.4) Single channel wireless wall switch for radio motor control.5) Four channel wireless wall switch for radio motor control.6) RS-232/Dry Contact - Allows for full control of radio motor shade via RS-


sensor.8) Wireless Timer - Allows operation of one group of radio motors per timer.9) Multi-Link RS232 to RTS Interface (16-channel).

5. Intelligent Technology Motor - 110 VAC motor with built-in low voltage controller with 3-wire pig tail and data cable. No external motor controls are required. Available with optional three-prong plug. Tubular motor concealed inside each shade roller tube.


1) Single Channel Handheld RF transmitter.2) 4-channel Handheld RF transmitter.3) 5-channel Handheld RF transmitter.4) Single Channel IR transmitter.5) Wireless Wall Switch - Wall switch for ILT motor control.

6. Quiet Intelligent Technology Motor - 110 VAC quiet motor with built-in low voltage controller with 3-wire pig tail and data cable. Motor operates at 44 Db measured 3 feet from the motor. Makes no audible clicks when motor stops or starts. Available with optional three prong plug. Tubular motor concealed inside each shade roller tube.


1) Single Channel Handheld RF transmitter.2) 4-channel Handheld RF transmitter.3) IP interface.4) Single Channel IR transmitter.5) Wireless Wall Switch - Wall switch for ILT motor control.

I. Roller Tube: Fabricated from extruded aluminum, galvanized steel, or enameled steel. Diameter, wall thickness, and material selected by manufacturer to accommodate shade type and size. Fabric connected to the roller tube with LSE (low surface energy) double sided adhesive specifically developed to attach coated textiles to metal. Adhesive attachment to eliminate horizontal impressions in fabric.

** NOTE TO SPECIFIER ** Include the following for LightBloc system and delete if not required. LightBloc system consists of aluminum headbox, side and sill channels.

** NOTE TO SPECIFIER ** Draper LightBloc FlexShade System is provided in two configurations: one for exposed surface installation and the other for recessed pocket installation. Delete the one not required.

J. Headbox: Consists of extruded aluminum sections with endcaps and opacity plates.1. Size: 4-1/8 inches (105 mm) high by 3-1/2 inches (89 mm) wide by length required for

shade being provided.** NOTE TO SPECIFIER ** Include the following paragraph for exposed headbox. Delete if not required.

2. L-shaped removable front face and bottom cover and L-shaped back and top.** NOTE TO SPECIFIER ** Include the following paragraph for recessed headbox. Delete if not

12494-24

required.3. U-shaped front, back, and top and removable bottom.

K. Endcaps: Stamped steel with universal design suitable for mounting to ceiling, wall, and jamb. Provide size compatible with roller size.

L. Side Channels: Double chamber fabricated from 0.06 inch (1.5 mm) thick extruded aluminum sections. One chamber accepts fabric and contains groove for fabric retainer. Other chamber accepts fabric guide and channel locator.

M. Sill channel: 0.06 inch (1.5 mm) thick extruded aluminum channel to receive slat bar and prevent light leakage.

N. Slat bar: Extruded aluminum bar attached to bottom of shade. Bar does not retract into headbox.

O. Channel locator: Injected molded nylon insert to align side and sill channels with headbox.

P. Fabric guide: Plated steel transition for fabric rolling into side channel.** NOTE TO SPECIFIER ** LightBloc FlexShades with SB9000 and SB9100 fabric use fabric retainers, that includes a patented system which enables shade to withstand reasonable air pressure differentials. However, extreme air currents or physical interference cannot be resisted by fabric retention system and may cause physical damage. Refer to Draper product literature for selection guidelines. (Available with SB9000 and SB9100 fabrics only).

Q. Fabric retainer: System designed to prevent disengagement of fabric from side channels due to normal variations of air pressure caused by doors opening, HVAC systems, and temperature differences between room and window well. System consists of horizontal steel stays installed in shade, covered with fabric, and spaced at regular intervals. Grommets installed through stays are held within groove of side channel chamber.

R. Exposed aluminum finish:** NOTE TO SPECIFIER ** Select the finish required from the following paragraphs and delete those not required.

1. Finish: Clear anodized aluminum.2. Finish: Black.3. Finish: White.4. Finish: Ivory.5. Finish: Bronze.6. Custom powder coat as selected by the Architect.

2.5 FABRIC** NOTE TO SPECIFIER ** Refer to Draper product literature for available shade fabrics and selection guidelines. Select fabric(s), percent open and color as applicable from the following and delete those not applicable. Use the schedule at the end of this section if required to define location(s) of multiple fabrics.

A. Light-Filtering Fabrics1. GreenScreen Revive 1%. GreenScreen Revive is a fire retardant PVC-free fabric

constructed of 100 percent polyester yarn, with a minimum of 89 percent Repreve polyester. Repreve is recycled and recyclable, contains low VOC's, and made in the USA. Fire rating: NFPA 701-99 TM#1, California U.S. Title 19, Cradle to Cradle Certified Silver, GREENGUARD, GREENGUARD Children & Schools, Green PVC Free. Approximate Openness Factor: 1 percent. Average Fabric Thickness: 0.019 inch (0.48 mm). Average Fabric Weight: 5.87 ounces per square yard.

2. GreenScreen Revive 5%. GreenScreen Revive is a fire retardant PVC-free fabric is

12494-25

constructed of 100 percent polyester yarn, with a minimum of 89 percent Repreve polyester. Repreve is recycled and recyclable, contains low VOC's, and made in the USA. Fire rating: NFPA 701-99 TM#1, California U.S. Title 19, Cradle to Cradle Certified Silver, GREENGUARD, GREENGUARD Children & Schools, Green PVC Free. Approximate Openness Factor: 5 percent. Average Fabric Thickness: 0.017 inch (.043 mm). Average Fabric Weight: 5.01 ounces per square yard.

3. SheerWeave Infinity2 sustainable window treatment fabric eco-friendly basketweave. Core yarn and coating are PVC-free, lead-free and 100 percent recycable. Fire classification: ASTM E-84 (Class I), NFPA 701-2004 TM#1 (small scale), NFPA 101 (Class A Rating) and CAN/ULC-S 109-03 Large, GREENGUARD, GREENGUARD Children & Schools, Green PVC Free.

** NOTE TO SPECIFIER ** Select percent open as applicable from the following and delete those not applicable.

a. Average 3 percent open. Average Fabric Thickness: .031 inch (.79 mm) Average Fabric Weight: 13.69 ounces per square yard. Available in 63 inch, 84 inch and 98 inch (1600 mm, 2134 mm and 2489 mm) roll widths.

b. Average 5 percent open. Average Fabric Thickness: .03 inch (.76 mm). Average Fabric Weight: 12.82 ounces per square yard. Available in 63 inch, 84 inch and 98 inch (1600 mm, 2134 mm and 2489 mm) roll widths.

4. SheerWeave Series SW3000 by Phifer: Vinyl coated fiberglass and vinyl coated polyester woven into 62 by 20 mesh. Fire rating: NFPA 701. Bacteria and Fungal Resistance: ASTM G 21 and ASTM G 22. 13.46 oz/sq yd, .028 inches thick. Average 14 percent open.

5. SheerWeave Series SW2000 by Phifer: VOC Emissions: GREENGUARD Children & Schools certified as a low emitting fabric. Manufacturer to supply GREENGUARD Children & Schools certificate. 500 denier fiberglass, vinyl coated and woven into a 2 by 2 basket weave. Fire rating: NFPA 701-1999TM#1 (small scale), NFPA 101 (Class A Rating), UBC (Class 1). Bacteria and Fungal Resistance: ASTM G 21 and ASTM G 22. 14.26 oz/sq yd, .019 inches thick. Series SW2000 average 5 percent open.

6. SheerWeave Series SW2100 by Phifer: VOC Emissions: GREENGUARD Children & Schools certified as a low emitting fabric. Manufacturer to supply GREENGUARD Children & Schools certificate. 500 denier fiberglass, vinyl coated and woven into a 2 by 2 basket weave. Fire rating: NFPA 701-1999TM#1 (small scale), NFPA 101 (Class A Rating), UBC (Class 1). Bacteria and Fungal Resistance: ASTM G 21 and ASTM G 22. 14.26 oz/sq yd, .019 inches thick. Series SW2100 average 10 percent open.

7. SheerWeave Series SW2500 by Phifer: VOC Emissions: GREENGUARD Children & Schools -certified as a low emitting fabric. Manufacturer to supply GREENGUARD Children & Schools certificate. 500 denier fiberglass, vinyl coated and woven into a 2 x 2 basket weave. Fire rating: NFPA 701. Bacteria and Fungal Resistance: ASTM G 21 and ASTM G 22. Series SW2500, 1 percent open, .024 inches thick.




11. Series SW2701 SheerWeave: Duplex basketweave fabric-light exterior color

12494-26

combined with dark interior color for thermal comfort and view-through. GREENGUARD Children & Schools certified as a low emitting fabric. Manufacturer to supply GREENGUARD Children & Schools certificate. Fire rating: NFPA 701. SW2701-.1 percent open.

12. Series SW2703 SheerWeave: Duplex basketweave fabric-light exterior color combined with dark interior color for thermal comfort and view-through. GREENGUARD Children & Schools certified as a low emitting fabric. Manufacturer to supply GREENGUARD Children & Schools certificate. Fire rating: NFPA 701. SW2703-3 percent open.



15. SheerWeave Series SW5000 by Phifer: Polyester and vinyl coated polyester woven into a 42 by 20 mesh. Fire rating: NFPA 701 TM#1/California Technical Bulletin 117 Sect. E. Part 1/NFPA 101 (Class A Rating)/UBC (Class 1)/British Standard 5867. Bacteria and Fungal Resistance: ASTM-G21 and ASTM G 22. 12.3 to14.5 oz/sq yd, .035 inches - .044 inches thick, depending on color. 5 to 10 percent open, depending on color.

16. SheerWeave Series PW4400 by Phifer: Vinyl coated polyester yarn woven into basketweave pattern. Fire rating: NFPA 701 TM#1(small scale)/California U.S. title 19 (small scale)/NFPA 101 (Class A Rating)/UBC (Class 1)/British Standard 5867/NFPA 701-TM#2 large scale/CAN/ULC S109-M-87. Bacteria and Fungal Resistance: ASTM G 21 and ASTM G 22. Series PW4400 Average 3 percent open, 20.7 oz/sq yd, .037 inches thick.



19. SheerWeave Series PW4600 by Phifer: Vinyl coated polyester yarn woven into basketweave pattern. Fire rating: NFPA 701 TM#1(small scale)/California U.S. title 19 (small scale)/British Standard 5867 Type B/ASTM E 84 (Class 1). Bacteria and Fungal Resistance: ASTM G 21 and ASTM G 22. Series PW4600, Average 3 percent open, 17.4 oz/sq yd, .030 inches thick.

20. SheerWeave Series PW4500 by Phifer: Vinyl coated polyester yarn woven into basketweave pattern. Fire rating: NFPA 701 TM#1(small scale)/California U.S. title 19 (small scale)/British Standard 5867 Type B/ASTM E 84 (Class 1). Bacteria and Fungal Resistance: ASTM G 21 and ASTM G 22. Series PW4500, Average 5 percent open, 14.4 oz/sq yd, .024 inches thick.

21. SheerWeave Series PW4650 by Phifer: Vinyl coated polyester yarn woven into basketweave pattern. Fire rating: NFPA 701 TM#1(small scale)/California U.S. title 19 (small scale)/British Standard 5867 Type B/ASTM E 84 (Class 1). Bacteria and Fungal

12494-27

Resistance: ASTM G 21 and ASTM G 22. Series PW4650, Average. 3 percent open, 13.3 oz/sq yd, .026 inches thick.

22. SheerWeave Series PW4550 by Phifer: Vinyl coated polyester yarn woven into basketweave pattern. Fire rating: NFPA 701 TM#1(small scale)/California U.S. title 19 (small scale)/British Standard 5867 Type B/ASTM E 84 (Class 1). Bacteria and Fungal Resistance: ASTM G 21 and ASTM G 22. Series PW4550. Average 5 percent open, 12.5 oz/sq yd, .025 inches thick.

23. SheerWeave PW4800 by Phifer: Vinyl coated polyester with maximum UV blockage. Fire rating: NFPA 701-1999 TM#1(small scale)/California U.S. title 19 (small scale)/NFPA 101 (Class A Rating)/UBC (Class 1)/British Standard 5867. Bacteria and Fungal Resistance: ASTM G 21 and ASTM G 22. 1 percent openness factor. 18.5 oz/sq yd, .030 inches thick.

24. SheerWeave - Basic by Phifer. An economical alternative to traditional solar screen fabrics. Fire Rating: California U.S. Title 19 (small scale), NFPA 701-2004 TM#1 (small scale), NFPA 101 (Class A Rating), UBC (Class I), BS 5867 2008 Part 2 Type B Performance, CAN/ULC-S109-03 (large and small scale) and NFPA 701 TM#2 (large scale), GREENGUARD, Microban. Average 3 percent Openness. Average Fabric Thickness: .025 inch. Average Fabric Weight: 16.4 ounces per square yard. Average 5 percent Openness. Average Fabric Thickness: 0.022 inch. Average Fabric Weight: 14.1 ounces per square yard.

25. E Screen ME-01 Series by Mermet: PVC coated fiberglass yarn woven in 2 by 2 basketweave. .016 inches thick. GREENGUARD Children & Schools certified as a low emitting fabric. Manufacturer to supply GREENGUARD Children & Schools certificate. Fire rating: NFPA 701, both small- and large-scale tests/California U.S. Title 19. ME-01 Series: Avg. 1 percent open.



28. E Screen ME-10 Series by Mermet: PVC coated fiberglass yarn woven in 2 by 2 basketweave. .016 inches thick. GREENGUARD Children & Schools certified as a low emitting fabric. Manufacturer to supply GREENGUARD Children & Schools certificate. Fire rating: NFPA 701, both small- and large-scale tests/California U.S. Title 19. ME Series: ME-10 Series: Avg. 10 percent open, 10.3 oz/sq yd. Okotex-labeled.

29. M Screen by Mermet: PVC coated fiberglass in 1 by 2 weave. GREENGUARD Children & Schools certified as a low emitting fabric. Manufacturer to supply GREENGUARD Children & Schools certificate. Fire rating: NFPA 701, both small- and large-scale tests/California U.S. Title 19. Okotex-labeled.

** NOTE TO SPECIFIER ** Select percent open as applicable from the following and delete those not applicable.

a. 3 percent openness 12.7 oz/sq yd, .022 inches thick.b. 5 percent openness 11.9 oz/sq yd, .022 inches thick.

30. T Screen 9803 by Mermet: PVC coated fiberglass woven mesh. Dark on one side, light on the other. GREENGUARD Children & Schools certified as a low emitting fabric. Manufacturer to supply GREENGUARD Children & Schools certificate. Fire rating: NFPA 701-99 TM #1, California U.S. Title 19. 12.1 oz/sq yd, .028 inches thick. T Screen 9603: Average 3 percent open.

31. Soltis 99 by Ferrari: PVC-coated polyester with silver backing on outside and pre-tensioning process for dimensional stability. 3 percent openness factor. 9 oz/sq yd, .0126 inches thick. Fire rating: NFPA 701. Easily accepts graphics. Recyclable,

12494-28

Okotex-labeled.32. Vela by Mermet: PVC-free fabric made from 100 percent FR polyester. Approximately

3 percent open. 6 oz./sq. yd., .015 inches thick. 100 percent recyclable. Fire rating: NFPA 701, small-scale test.

33. SilverScreen by Mermet: 36 percent fiberglass and 64 percent vinyl with an ultra-fine layer of aluminum on the backside. Fire classifications: NFPA 701-99 TM#1, M1 NFP 92-503, GREENGUARD, GREENGUARD Children & Schools, RoHS Lead Free, GREENGUARD, GREENGUARD Children & Schools, Oeko-Tex. Approximate Openness Factor: 5 percent. Average Fabric Thickness: 0.020 inch. Average Fabric Weight: 12.86 ounces per square yard.

B. Room Darkening Fabrics1. SunBloc Series SB9000: Close woven fiberglass base textile with sun-resistant vinyl

film bonded to each side, opaque with minimum tensile strength of 190 pounds for warp and 180 pounds for fill. Fire rating: NFPA 701 1006-Test 1. Washable and stain resistant. Wt. 12 oz/sq yd. Same color both sides, .015 inches thick.

2. SunBloc Series SB9100: Close woven fiberglass base textile with sun-resistant vinyl film bonded to each side, opaque with minimum tensile strength of 190 pounds for warp and 180 pounds for fill. Fire rating: NFPA 701 1006-Test 1. Washable and stain resistant. Wt. 12 oz/sq yd. White exterior in all colors, .013 inches thick.

3. Flocke by Mermet: Opaque, PVC-free fiberglass textile with acrylic backing. 17.1 oz/sq yd, .024 inches thick. Fire rating: NFPA 701, both small- and large-scale tests. Antistatic treated. Draper shades made with this fabric are GreenSpec listed.

4. SheerWeave Series SW7000 by Phifer: PVC-free polyester with acrylic foamed backing. .018 inches thick, 10 oz/sq yd, opaque. Draper shades made with this fabric are GreenSpec listed.

5. SheerWeave Series SW7100 by Phifer: PVC-coated Fiberglass laminated with a 2-ply PVC film. Fire rating: NFPA 701.023 inches thick, 19.8 oz/sq yd, opaque.

6. Edessa Twilight Residential by Mermet. 100 percent Polyester with a "fabric" look and feel. Rated FR. Fire classifications: ASTM E84, GREENGUARD, GREENGUARD Children & Schools, RoHS-Lead Free, PVC Free, GREENGUARD, GREENGUARD Children & Schools. Approximate Openness Factor: 0 percent. Average Fabric Thickness: .020 inch. Average Fabric Weight: 11.4 ounces per square yard.

7. Vizela 1 percent by Mermet: 100 percent fiberglass with an EVA coating and PVC free. Fire classifications: NFPA 701-10 TM#1, California U.S. Title 19, ASTM E-84, M1 NFP 92 503, GREENGUARD, GREENGUARD Children & Schools, RoHS Lead Free, PVC Free, ASTM G21 Fungal Resistance and ASTM E2180 Bacteria Resistance rated, GREENGUARD, GREENGUARD Children & Schools. Approximate Openness Factor: 1 percent. Average Fabric Thickness: 0.013 inch. Average Fabric Weight: 8.7 ounces per square yard.

** NOTE TO SPECIFIER ** Refer to Draper product literature for available shade fabric colors and patterns. Select fabric colors and patterns from the following, delete those not applicable.

C. Color and pattern: __________, No. _____.

D. Color and pattern: As indicated in Color Schedule on Drawings.

E. Color and pattern: As selected by Architect from manufacturer's standard range.

PART 3 EXECUTION

3.1 EXAMINATION

A. Do not begin installation until substrates have been properly prepared.

B. If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

12494-29

3.2 PREPARATION** NOTE TO SPECIFIER ** Include one of the following paragraphs. Delete if not applicable.

A. Coordinate requirements for blocking and structural supports to ensure adequate means for installation of window shades.

B. Coordinate requirements for blocking, construction of shade pockets, and structural supports to ensure adequate means for installation of window shades.

** NOTE TO SPECIFIER ** Include one or more of the following paragraphs for window shades with headboxes recessed in ceilings. Delete those not applicable.

C. Coordinate installation of recessed shade pockets with construction of suspended acoustical panel ceilings specified in Section 09510.

D. Coordinate installation of recessed shade pockets with construction of suspended gypsum board ceilings specified in Section 09260.

** NOTE TO SPECIFIER ** Include the following paragraph for motorized shades. Delete if not applicable.

E. Coordinate requirements for power supply conduit, and wiring required for window shade motors and controls.

3.3 INSTALLATION

A. Install in accordance with manufacturer's instructions.

B. Install roller shades level, plumb, square, and true. Allow proper clearances for window operation hardware.

** NOTE TO SPECIFIER ** Draper Type D FlexShade Pockets are designed to be installed prior to or as part of ceiling system installation. Shade and operating mechanism can be site installed in pockets after construction operations that might damage shade are complete. If pockets are to be installed. Include the following paragraph as applicable and delete if not applicable.

C. Shade pockets:1. Install shade pockets prior to installation of suspended ceiling system. Attach to

supporting structure with screws through top of pocket at 24 inches (610 mm) minimum centers.

2. Install shade pockets in conjunction with installation of suspended ceiling system. Attach to supporting structure with screws through top of pocket at 24 inches (610 mm) minimum centers.

3. Install corner pieces securely and in alignment with pockets.4. Install pocket ends securely and in alignment with pockets.5. After interior construction is essentially complete, install shade and operating

mechanism in pocket.** NOTE TO SPECIFIER ** Include the following paragraph if fascia or separate closure for site constructed recess is being provided. Note fascia is not applicable if pockets are being provided. Delete if not applicable.

D. Install the following items to conceal roller and operating mechanism. Do not use exposed fasteners.

** NOTE TO SPECIFIER ** Select items to conceal roller and operating mechanism from the following as applicable. Delete if not applicable.

1. Fascias.2. Closure panels.3. Endcaps.

12494-30

** NOTE TO SPECIFIER ** Include the following paragraphs for LightBloc shades. Delete if not applicable.

E. Install headbox, side channels, and sill channel with sealant specified in Section 07900 - Joint Sealers to eliminate light leaks at perimeter of shade system.

F. Position shades level, plumb, and at proper height relative to adjacent construction. Secure with fasteners recommended by manufacturer.

3.4 TESTING AND DEMONSTRATION** NOTE TO SPECIFIER ** Include the following paragraph for motorized shades. Delete if not applicable.

A. Test motorized window shades to verify that controls, limit switches, interface to other building systems, and other operating components are functional. Correct deficiencies.

** NOTE TO SPECIFIER ** Include the following paragraph for LightBloc shades. Delete if not applicable.

B. Test window shades to verify that operating mechanism, fabric retainer, and other operating components are functional. Correct deficiencies.

** NOTE TO SPECIFIER ** Select one type operating mechanism from the list below. Delete those not applicable.

1. Crank.2. Chain and clutch.3. Motorized operating mechanism.

** NOTE TO SPECIFIER ** Include the following paragraph for LightBloc shades. Delete if not applicable.

C. During daylight hours, lower shades and turn off interior lights. Verify that there are no light leaks at perimeter or within shade assembly. Correct deficiencies.

D. Demonstrate operation of shades to Owner's designated representatives.

3.5 PROTECTION

A. Protect installed products until completion of project.

B. Touch-up, repair or replace damaged products before Substantial Completion.

3.6 SCHEDULES** NOTE TO SPECIFIER ** Retain Paragraph below to suit project requirements. Identify products by name on the Drawings or alternately use this paragraph to define the location of each type of material to be used. Delete if not required.

A. Refer to Drawings for shade types and locations.

END OF SECTION

12494-31

arcat · web viewarcat ... 12494-1

Documents