06 - 11 engnlishnldo - lariuslarius.org/manuali/vikingline_uk.pdf · in any case, cleaning, ......

ENGLISH

Ed.

003

06 -

11

VIKING LINERDOUBLE COLOUR STREET MARKING

SELF-PROPELLED WITH SEQUENCER

P A I N T S P R A Y I N G E Q U I P M E N T

OPE

RATI

NG A

ND M

AINT

ENAN

CE IN

STRU

CTIO

NSO

PERA

TING

AND

MAI

NTEN

ANCE

INST

RUCT

IONS

1

English

VIKING LINER

WE ADVISE THE USE OF THIS EQUIPMENT ONLY BY PROFESSIONAL OPERATORS.ONLY USE THIS MACHINE FOR USAGE SPECIFICALLY MENTIONED IN THIS MANUAL.

Thank you for choosing a LARIUS S.R.L. product.As well as the product purchased,

you will receive a range of support servicesenabling you to achieve the results desired,

quickly and professionally.

SELF-PROPELLED PROFESSIONAL LINE-MARKER

ABCDE

F

G

H

I

JKLM

NOP

QR

S

TUVWXYZAA

INTRODUCTION ...........................................................p.1

WARNINGS ...................................................................p.2

WORKING PRINCIPLE ......................................p.3

TECHNICAL DATA ..............................................p.4

DESCRIPTION OF THE EQUIPMENT ...............p.6

TRANSPORT AND UNPACKING .......................p.10

SAFETY RULES .................................................p.10

SETTING-UP ......................................................p.11

OPERATION .......................................................p.14

PAINTING OPERATIONS ...................................p.16

CATADIOPTRIC PEARLS DISTRIbUTING

KIT ......................................................................p.17

ADJUSTMENTS .................................................p.18

CLEANING AT THE END OF WORK .................p.19

GENERAL MAINTENANCE ...............................p.20

ROUTINE MAINTENANCE ...................................p.20

DESCRIPTION OF CONTROLS ........................p.21

TROUbLESHOOTING ........................................p.23

CORRECT PROCEDURE OF

DECOMPRESSION ............................................p.24

HIGH PRESSURE GUN AT 250 .........................p.26

ExPLODED vIEW GUN LA 95 ..........................p.27

COMPENSATION vALvES .................................p.28

SUCTION SYSTEM ............................................p.29

COMPLETE HYDRAULIC bODY .......................p.30

COMPLETE COLOUR bODY .............................p.32

INTERNAL COMbUSTION ENGINE .................p.34

CONTROL PANEL USE .....................................p.35

LINES SEQUENCING FUNCTION ...................p.37

SPACE AND LINE SETTINGS ...........................p.40

ACCESSORIES ..................................................p.42

2

Engl

ish

VIKING LINER

Read this operator’s manual carefully before using the equipment.An improper use of this machine can cause injuries to people or things.Do not use this machine when under the influence of drugs or alcohol.Never modify the equipment under any circumstances.Use products and solvents that are compatible with the various parts of the equipment, and read the manufacturer’s warnings carefully.Refer the Technical Details for the equipment given in the Manual.Check the equipment for worn parts once a day. If any worn parts are found, replace them using ONLY original spare parts.Keep children and animals away from work area.Comply with all safety standards.

It indicates an accident risk or serious damage to equipment if this warning is not followed.

It indicates important recommendations about disposal and recycling process of products in accordance with the environmental regulations.

WARNINGS The table below provides the meaning of the symbols used in this manual in relation to using, earthing, operating, maintaining, and repairing of this equipment.

It indicates a fire or explosion risk if this warning is not followed.Remove all ignition sources such as pilot lights, cigarettes, portable electric lamps and plastic drop cloths.Keep work area free of debris.ONLY use this equipment in a well ventilated area.EARTH ALL THE EQUIPMENT LOCATED IN THE WORK AREA.Never form connections or switch any light on or off in presence of inflammable fumes.If electrical shocks or discharges are encountered, immediately stop the operation being carried out on the equipment.Keep a fire extinguisher at hand near the work area.

It indicates the risk of lesions and finger crushing due to movable parts on the equipment.Keep far from moving parts.Do not use the equipment without the suitable protections.before any inspection or maintenance of the equipment, carry out the decompression procedure explained in this manual, and prevent any risk of the equipment starting unexpectedly.

These symbols indicate the risk of chemical reactions or explosions if this warning is not followed.There is a risk of injury or serious lesion related to contact with the jet from the spray gun. If this should occur, IMMEDIATELY contact a doctor, indicating the type of product injected.Do not spray before the guard has been placed over the nozzle and the trigger on the spray gun.Do not put your fingers on the spray gun nozzle.Once work has been completed, before carrying out any maintenance inervention, perform the decompression procedure explained in this manual.

It indicates any danger of electric shock if the warning and presence of live electrical parts has not been indicated.Store in a dry place and do not expose to the rain.Check that the cables are in good condition.Switch off the equipment and discharge any electricity before cleaning or maintaining the equipment.

It indicates the presence of a terminal with grounding cable.Use ONLY 3-wire extension cords and grounded electrical outlets.before starting work make sure that the electrical system is earthed and that it complies with safety standards.

It is recommended to wear suitable clothing as gloves, goggles and face shields.Wear clothing that complies with the safety standards in force in the country in which the equipment is used.Do not wear bracelets, earrings, rings, chains, or anything else that may hinder the operator’s work.Do not wear clothing with wide sleeves, scarves, ties, or any other piece of clothing that could get tangled up in moving parts of the equipment during the work, inspection, or maintenance cycles.

Danger: laser light. Protect your eyes.

3

English

VIKING LINER

A WORKING PRINCIPLEThe VIKING LINER is a self-propelled device which has been conceived and designed for performing road markings along particularly difficult tracts of uneven road where marking would otherwise be difficult to complete.The internal combustion engine, mounted upon the undercarriage, powers the pump and the alternator which is employed for charging the battery unit. The two-wheel frontal-traction is powered by an electric motor which allows the operator to easy move, even on medium-grade inclines. The control zone offers the possibility of: • Activating the two spraying guns;• Enabling or disabling the frontal steering wheel;• Increasing the number of motor revolutions;• Enabling / disabling front-wheel traction;• Gradually increasing the advancement speed of the self-propelled

undercarriage;• Opening / closing the flow to the 2nd spray gun;• Selecting continuous or dotted line painting functionality.

This type of device is capable of marking simultaneousl two side-by-side lines of the same colour or of different colours.The lines may be continous, broken or mixed.

CONTINUOUS LINES

1 2

DOTTED LINES

MIXED LINES

3

VIKING LINER is perfect for large-scale lining and maintenance works.

Use water or non-refractive solvent filtered paint specifically designed for airless applications.

VIKING LINER allows the marking and maintaining of all types of lines on highways, freeways, pedestrian crossings, parking lots and squares, as well as every horizontal marking required by the highway code.Airless marking has numerous proven benefits with respect to line-markers with pressurised tanks, which have been rendered obsolete by airless-technology line markers.

Airless line-marking guarantees: • Reduced Environmental Impact;• Reduced drying time.

The paint dries quickly and the line is defined in an even manner with a single coat. The airless function requires the use of filtered paint which is specifically designed for airless application. This means that the paint is homogeneous, of a smooth and even consistency and will not form crusts, nor will it become gelatinous or thick. With this airless line-marker, the paint adheres firmly to all types of pavement, with optimal visibility and resistance to wear caused both by traffic and atmospheric agents.

The refractive effect is ob-tained though the release of refractive spheres from an appropriate tank.These spheres automatically “fall” onto the painted line and, for this reason, pre-mixed or beaded paints do not have to be used. The proper operation of the device is granted by the exclusive use of suitable and quality paints. A high degree of safety and cleaning of the workplace is achieved thanks to the absence of pressurised tanks.

In the LARIUS models, the paint canister can be loaded directly upon the undercarriage or else pou-red into the non-stick, 50 L tank. In any case, cleaning, maintenance and colour change operations are easy to perform.

The line-marker is equip-ped with a 360° pivoting frontal wheel which even increases the agility of the larger models.High yield, high efficiency, high versatility.

This line-marker utilises non-premixed paints. This allows it to achieve a yield of about 30% more than standard line-markers. Every model is also an airless spray gun which can be used in the construction field together with washable products, enamels, breathable paints and flooring resins.A vast range of accessories is available to satisfy any customer request.

4

Engl

ish

VIKING LINER

A

C

B

LA95 airless gunFor lines from 3 to 30 cm wide, mounted on an adjustable block: modify the spray pattern by adjusting the height of the gun or nozzle.

WORKING PRINCIPLE

The unit VIKING LINER is defined “diaphram pump”. This pump is used for high pressure painting without air (from this process derives the term “airless”). The pump is controlled by a motor coupled with a reduction gear. A cam shaft and a connecting rod allow to obtain the reciprocating motion necessary to the working of the “pumping group” diaphram.

The diaphram movement produces a “depression”. The product is sucked, pushed towards the pump outlet and then sent to the gun through the high pressure flexible hose. A mechanical device allows to adjust and control the pressure of the material coming out of the pump. A safety valve avoiding overpressur guarantees the total reliability of the equipment.

TECHNICAL DATA

VIKING LINER

SUPPLY motor Power mAX oPerAting PreSSUremAX DeLiVerYweightnoiSe PreSSUre LeVeLLenghtwiDth height

UNLEADED PETROL2,6 kW

220 bar (3190 PSI)4,5 Kw L/min - 1,18 USG

130 Kg 70dB(A)

(A) 1650 mm(B) 750 mm

(C) 1000 mm

400 mm ø pneumatic wheels They guarantee stability and easy movement and reduce the unevenness of the road's surface.

B

Head Liner ControlEasy and functional with: Automatic marking sequencer, electronic speed control and built-in safety devices.

5

English

VIKING LINER

STANDARD EQUIPMENT ACCESSORIES MODELS

APPLICATION FIELDS

• External or underground parking lots (schools, ho-tels, airports, supermarkets, train stations, subway stations, ports);

• External public areas;

• Industrial and exhibition building areas;

• Freeway service areas and service stations;

• Pedestrian median lines, intersections, bicycle tracks, reserved lanes;

• Internal and external logistic area mar-kings;

• Playing fields.

Nozzle heightfrom ground

10 cm

15 cm

20 cm

25 cm

30 cm

35 cm

~ 3 cm

~ 6 cm

~ 10 cm

20° angle line width

~ 5 cm

~ 7 cm

~ 8 cm

~ 10 cm

~ 12 cm

40° angle line width

60° angleline width

~ 10 cm

~ 13 cm

~ 16 cm

~ 20 cm

~ 23 cm

~ 26 cm

NOZZLES POSITION TABLE

N° 2 Filters with pressure gauge

N° 2 High pressure tube diameter 3/16" mt 10

N° 2 Diaphram buffers

N° 2 Suction - recirculation systems

N° 2 Manual airless guns AT250

N° 2 Super fast clean bases

N° 2 Super fast clean nozzles 11-40

N° 2 Super fast clean nozzles13-40

N° 1 Tools pack

Rif. 4405Reflecting pearls dispenser for manual gunsRif. 4405/1Reflecting pearls dispenser for auto-matic gunsRif. 4038Laser pointer kitRif. 4506Working spotlightRif. 4711Operator platform

Rif. 4900viking liner manual mode

Rif. 4920viking liner + autotraction

Rif. 4950viking liner + autotraction + automatic dotted-line marking sequencer

6

Engl

ish

VIKING LINER

8

9

7

2

8

51

4

6

5

POS. Description

1 Airless manual gun AT 250 2 High pressure hose 3 Spotlight 4 Guns holding arm5 Airless spraying guns LA95

POS. Description

6 Stabilizer lifting cylinder7 Additional cord pull-start ignition8 Reflecting pearls dispenser9 Super fast clean nozzle

DESCRIPTION OF THE EQUIPMENT

7

8 5 6

4

5

3

C

7

English

VIKING LINER

19

20

18

16

15

10

POS. Description

10 Automatic lever for continuos or dotted line painting selection11 Internal combustion engine

12 Intake filter13 Product container14 Reflecting pearls dispenser15 Internal combustion engine accelerator

POS. Description

16 Machine driving lever17 Petrol tank

18 Forward / backward selector19 Spotlight switch20 Manual spraying control switch

12

11

12

14

12

16

10

15

11

13

8

Engl

ish

VIKING LINER

POS. Description

21 Control Head Liner 22 Flashing light23 Pneumatic system supply compressor24 Compressor pressure switch

POS. Description

25 Front steering wheels 26 Electric motor for forward/reverse movement27 Direction locking / releasing lever28 Clutch releasing lever

23

21

26

24

27

28

21 22

23

27

28

25

9

English

VIKING LINER

POS. Description

29 Recirculation tube valve30 Delivery filter

31 Manual Airless sprayer delivery valve 32 Cooling fan33 Product supply tube

POS. Description

34 Recirculation hose35 Pressure adjusting knob36 buffer37 Oil cooling radiator38 Pressure gauge

35

37

36

31

3433

29

38

30

32

29

34

37

34

33

10

Engl

ish

VIKING LINER

The user is responsible for the operations of unlo-ading and handling of the equipment and should pay the utmost attention so as to avoid any damage to people or things.Unloading operations shall be performed only by qualified and trained personnel (truck and crane operators, etc.) with hoisting devices suitable for the weight of the installation or its parts. Carefully follow all safety rules. The personnel must be equipped with suitable safety clothing.

D TRANSPORT AND UNPACKING• The packed parts should be handled as indicated in the

symbols and markings on the outside of the packing.

• before installing the equipment, ensure that the area to be used is large enough for such purposes, is properly lit and has a clean, smooth floor surface.

• The manufacturer will not be held responsible for the unloading operations and transport of the machine to the workplace.

• Check the packing conditions upon receipt of the equip-ment. Unpack the machine and verify if there has been any damage due to transportation.

In case of damage, call immediately LARIUS and the Shipping Agent.

Any notice about damages or faults shall be sent within 8 days at least from the date of receipt of the equipment through Registered Letter with return receipt to the Ship-ping Agent and to LARIUS.

SAFETY RULES

• THE EMPLOYER SHALL TRAIN ITS EMPLOYEES AbOUT ALL THOSE RISKS STEMMING FROM ACCIDENTS, AbOUT THE USE OF SAFETY DEvICES FOR THEIR OWN SAFETY AND AbOUT THE GENERAL RULES FOR ACCIDENT PREvENTION IN COMPLIANCE WITH INTERNATIONAL REGULATIONS AND WITH THE LAWS OF THE COUNTRY WHERE THE PLANT IS USED.

• THE bEHAvIOUR OF THE PERSONNEL SHALL STRICTLY COMPLY WITH THE ACCIDENT PREvENTION RULES AND THE ENvIRONMENTAL REGULATIONS IN FORCE IN THE COUNTRY WHERE THE PLANT IS INSTALLED AND USED.

• KEEP YOUR WORK PLACE CLEAN AND TIDY. DISORDER WHERE YOU ARE WORKING CREATES A POTENTIAL RISK OF ACCIDENTS.

• ALWAYS KEEP PROPER bALANCE AvOIDING UNUSUAL STANCE.

• bEFORE USING THE EQUIPMENT, MAKE SURE THERE ARE NOT DAMAGED PARTS AND THE MACHINE CAN WORK PROPERLY.

• ALWAYS FOLLOW THE INSTRUCTIONS AbOUT SAFETY AND THE REGULATIONS IN FORCE.

• KEEP UNAUTHORISED PEOPLE OUT OF THE WORK AREA.

• NEVER ExCEED THE INDICATED MAxIMUM OPERATION PRESSURE.

• NEVER POINT THE SPRAY GUN TOWARDS YOURSELF

OR OTHER PEOPLE. THE CONTACT WITH THE JET CAN CAUSE SERIOUS INJURIES.

• IN CASE OF INJURIES CAUSED bY THE GUN JET, SEEK

IMMEDIATE MEDICAL ADvICE SPECIFYING THE TYPE OF THE PRODUCT INJECTED. NEVER UNDERvALUE A WOUND CAUSED bY THE INJECTION OF A FLUID.

• ALWAYS STOP THE MOTOR AND DISCHARGE THE PRESSURE IN THE CIRCUIT bEFORE PERFORMING ANY CHECK OR PART REPLACEMENT OF THE EQUIPMENT.

• NEvER MODIFY ANY PART IN THE EQUIPMENT. REGU-LARLY CHECK THE COMPONENTS OF THE SYSTEM. REPLACE ANY DAMAGED OR WORN PART.

The disposal of packaging materials is at user’s care and must be performed in accordance with the regulations in force in the country where the plant is installed and used. It is nevertheless good practice to recycle packaging materials in an environment-friendly manner as much as possible.

Read carefully and entirely the following instructions before using the product. Please save these instructions in a safe place.The unauthorised tampering/replacement of one or more parts composing the machine, the use of accessories, tools, expendable materials other than those recommended by the manufacturer can be a danger of accident. The manufacturer will be relieved from any civil and penal responsibility.

E

11

English

VIKING LINER

F1

SETTING-UPCONNECTION OF THE GUNS

• Connect the high pressure hoses (F1) to the pump and to the guns (F2), taking care to fasten the connections tightly (we recommend using two wrenches).

NEVER use any sealing products for threads on the fittings.

• It is recommended to use the hose provided with the stan-dard kit.

NEVER use a damaged or a repaired flexible hose.

Engine safety precautions:

• Read the motor manual herewith enclosed.

• TIGHTEN AND CHECK ALL THE FITTINGS FOR CONNEC-TION bETWEEN PUMP, FLExIbLE HOSE AND SPRAY GUN bEFORE USING THE EQUIPMENT.

• ALWAYS USE THE FLExIbLE HOSE SUPPLIED WITH STANDARD KIT. THE USE OF ANY ACCESSORIES OR TOOLING OTHER THAN THOSE RECOMMENDED IN THIS MANUAL MAY CAUSE DAMAGE OR INJURES.

• THE FLUID CONTAINED IN THE FLExIbLE HOSE CAN bE vERY DANGEROUS. HANDLE THE FLExIbLE HOSE WITH CARE. DO NOT PULL THE FLExIbLE HOSE TO MOvE THE EQUIPMENT. NEvER USE A DAMAGED OR A REPAIRED FLExIbLE HOSE.

The high speed of the product flowing in the hose can create static electricity through discharges and sparks. The pump is grounded by means of a sliding chain.

• NEvER SPRAY OvER FLAMMAbLE PRODUCTS OR SOL-vENTS IN CLOSED PLACES.

• NEvER USE THE EQUIPMENT IN PRESENCE OF POTEN-TIALLY ExPLOSIvE GAS.

Always check that the product is compatible with the materials composing the equipment (pump, spray gun, flexible hose and accessories) with which it may come into contact. Never use paints or solvents containing halogen hydrocarbons (as the methylene chloride). If these products come into contact with aluminium parts can provoke dangerous chemical reactions with risk of corrosion and explosion.

IF THE PRODUCT TO bE USED IS TOxIC, AvOID INHALATION AND CONTACT bY USING PRO-TECTION GLOvES, GOGGLES AND PROPER FACE SHIELDS.

TAKE SUITAbLE SAFETY MEASURES FOR THE PROTECTION OF HEARING WHEN OPERATING NEAR THE EQUIPMENT.

Never try to tamper with the adjustment values of instruments.

F

F2

12

Engl

ish

VIKING LINER

F6F7

F9

F4

F3

F5

F2

F5

F10

ON

CONNECTION OF THE MANUAL GUN• Connect the high pressure flexible hose (F3) to the fitting

(F4) and to the gun (F5) tightening the fittings strongly (the use of two wrenches is suggested).

WASHING OF THE NEW EQUIPMENT

• The equipment has already been adjusted at our factory with light mineral oil left inside the pumping group as protection. Therefore, wash with thinner before sucking the product.

• Fill the product tank with washing liquid.• Ensure the guns (F2-F5) are without nozzle.

• Pull lever (F6) for first start-up (only when cold). Open the fuel tap (F7).• bring the accelerator lever (F8) to about 1/2 of its run.• Turn the key (F9) to enable the electric ignition.

• Turn the switch (F10) to ON (I) in order to enable the control Head Liner panel.

F8

13

English

VIKING LINER

F11F15

F16

• Slightly turn pressure regulating knob (F11) clockwise so that the machine idles.

• Open the re-circulation valve (F12a) and (F12b).• visually check that the washing liquid starts to re-circulate

within the tank (F13).• Close the re-circulation valve (F12a) and (F12b).• Open the tap (F14) of the manual gun.

• Point the manual gun (F15) towards a collecting container (F16) keeping the trigger lever pressed (so as to drain the oil inside) till a clean solvent comes out. Now, release the lever.

F12a

F12b

F13

• Close the tap (F14) of the manual gun.

F14

14

Engl

ish

VIKING LINER

• Perform the same operation for the automatic spray guns as well (see Head Liner control board instructions).

• Remove any solvent remaining within the tubes by activating the manual and automatic guns.

• As soon as the pump begins to idle, turn the handle (F11) to minimum to stop the system.

Absolutely avoid spraying solvents in closed envi-ronments. It is also recommended to keep the spray gun away from the pump in order to prevent vapours from coming into contact with the electrical motor.

• Stop the internal combustion engine.• At this point the machine is ready. If water-based paints are

to be used, after the washing with solvent, it is recommended to wash the tank again with soap and water, then rinse with clean water (repeating the previously described procedures).

• Insert the manual gun trigger lock and fix the nozzle.• Insert the automatic guns trigger lock and fix the nozzles.

PREPARATION OF THE PAINT

• Make sure the product is suitable to be used with a spray gun.

• Mix and filter the product before using it. For filtration use CLOSE-MESH (ref. 214) and LARGE-MESH (ref. 215) LARIUS METEX braids.

• Fill the tank (F13) with the paint.

Never use products containing halogen hydrocarbons (as methy-lene chloride). If these products come into contact with aluminium parts of the equipment can provoke dangerous chemical reactions with risk of explosion.

Make sure the product to be used is compatible with the materials employed for manufacturing the equipment (stainless steel and aluminium). For this purpose, please contact the supplier of the product.

G2

G3

G1

• Enable the engine ignition control with the key (G3).

• Check that there is enough unleaded petrol. Turn fuel (G2) knob to “ON”.

OPERATION

SETUP PROCEDURE

• Use the equipment only after performing all the SETTING UP operations described in the previous pages.

• Make sure that all the levers are in the “RELEASE” position, that is nothing is engaged.

• Check that the automatic lever (G1) is in its “0” position.

G

15

English

VIKING LINER

• Open the re-circulation valve (G4a) and (G4b).• Turn slightly pressure regulating knob (G5) clockwise so that

the machine idles.• visually check that the product starts to re-circulate within

the tank.• Close the re-circulation valve (G4a) and (G4b).• Open the tap (G6) (if necessary only for painting with the

manual gun).• Turn the pressure adjustment handle (G5) to the suitable

operation value.

G4a

G4b

G6

• At this point the machine will continue to suck the product till the flexible hose is full, up to the gun, and then it will stop automatically once reached the preset pressure.

COMPRESSOR

G8

G10

• Activate the compressor (G8) (adjust the compressor pressure to 6 bar).

ADJUSTING THE INTERNAL COMBUSTION ENGINE SPEED

• Gently move the motor acceleration lever (G10) to increase or decrease the speed of the pump.

During the painting operation it is normally recommended to maintain the position of the accelerator lever (G10) at about 3/4 of its run.

• Release the clutch using the lever (G9), in order to be able to move the machine more easily and accurately.

G9

16

Engl

ish

VIKING LINER

H3

H4

H5

PAINTING OPERATIONS• Tunr the pressure adjusting knob (H1) and (H2) to the suitable

operation value.

• It is possible to switch the control lever (H3) placed on the right handle, on position "AUT" (AUTOMATIC) or on position "MAN" (MANUAL) to set the operation conditions of the automatic guns.

(See the “control bridge use” section for programming).

• The machine is outfitted with a third manual (H4) gun with a 15-meter tube (H5) to perform roadside writings with paint templates.

The gun is situated under the control handles placed on the special tube winder.

• In order to use the manual spray gun, open the valve (H6) located at the delivery filter’s outlet.

A

B

H7

H8

H7

• If operation is required upon a long rectilinear section, the lever (H7) must be placed in its “A” position. A spring-action mechanical stopper will automatically block the front wheel (H8) in its straight position, thereby ensuring a straight tra-jectory for the operator.

A = ConnectedB = Disconnected

H H6

H1 H2

17

English

VIKING LINER

H9

RUN

SPRAYING JET ADJUSTMENT

• Slowly turn clockwise the pressure control knob (H10) to reach the pressure value able to grant a good atomization of the product.

• An irregular and marked spray on the sides indicates a low working pressure. On the contrary, a too high pressure causes a high fog (“overspray”) and waste of product.

• In order to avoid excess paint thickness, do not spray if not simultaneously advancing with the machine.

Recirculation safety valve: when working at the maximum pressure available, the release of the gun trigger may cause sudden increases of pressure. In this case, the recirculation safety valve opens automatically discharging part of the product from the recirculating tube. Then it closes so as to restore the previous working conditions.

After having used the equipment, follow all the pro-cedures for decompression and cleaning indicated in the manual. At the end of the work, switch the levers into the resting position.

• Press the advancement lever (H9) and begin to work based on the set cycle by activating the gun control lever "AUT" or "MAN" (H3).

H3

H10

CATADIOPTRIC PEARLS DI-STRIBUTING KIT

DESCRIPTION OF THE EQUIPMENT

With the new distribution system of reflecting pearls, the “VIKING LINER” unit can produce a more visible and therefore safer roadway indication, even in the worst weather conditions.The pearlized distribution kit is composed of a drop tank with two openings, two rubber tubes that carry the reflecting pearls to the dispensers.

POS. Description

1 Drop tank2 Filling tubes3 Dispensers4 Catadioptric material distributing valve

1

4

I

2

3

18

Engl

ish

VIKING LINER

ADJUSTMENTS

a

b

cd

J4 J5 J6

J7 J13 J8 J14J9

J10

J11

ADJUSTING GUNS POSITION

The guns (J4) are mounted on suitable sliding arms (J5), (J6), (J7), (J8). This allows the correct positioning of the guns according to working requirements. The movements are indicated by the arrows (a), (b), (c), (d).In order to allow the shifting of the guns on the relevant arms, it is necessary to release the handles (J9), (J10), (J11), (J12) and the screws (J13), (J14).Once the adjustment is completed, provide to duly tighten handles and screws.

J ADJUSTING THE REFLECTING PEARLS DISTRIBUTION UNIT

To set the position of the reflecting pearls distributors (J15) it is necessary to adjust the screws (J16).

J16

J16

J15

J16

ADJUSTING THE PNEUMATIC SYSTEM PRESSURE

In order to regulate the pressure in the pneumatic system, turn the knob (J10) clockwise (+) to increase the pressure and counter-clockwise (-) to reduce it.

Before adjusting the pressure, start the compres-sor using the button (J9).

19

English

VIKING LINER

+-

ON OFF

J10

J9

CLEANING AT THE END OF WORK• Reduce pressure to the minimum [turn counterclockwise the

pressure control knob (K1)].

K

K1 K1

K1 K1

• Press the switch (K2) placed on the box of the electric motor to its OFF (0) position to stop the motor pump.

K2

OFF

• Open the recirculation safety valve (K3a) and (K3b) to di-scharge the pressure in the circuit.

K3a

K3b

• Lift the suction pipe and replace the product tank with that of the solvent (make sure it is compatibie with the product being used).

• Unscrew the gun nozzle (do not forget to clean it with solvent or water if you used hydrosoluble paints).

• Press the ON (I) switch and slightly turn the pressure control knob (K1) clockwise so as the machine works until the connection to the engine is trigged.

20

Engl

ish

VIKING LINER

Follow the washing procedure before usingthe equipment again.

K4

K5

GENERAL MAINTENANCEDAILY

• Clean the filters;• Clean the nozzles;• Clean all the paint circuit with a specific product;• Check the fuel motor (see maintenance table).

PERIODICALLY

• Clean the movable parts from the paint deposits (clutch traction, spray guns, etc.);

• Check the gun cables tightening, the wheel block and the traction;

• Check that the tubes and all the fittings are correctly tightened.

L

M1

• Make sure the solvent recycles from the recirculation tube.

• Point the gun towards the product collection tank and, keeping the trigger pressed, discharge the remaining product till a clean solvent comes out. Now, release the trigger.

• Lift again the suction pipe and remove the solvent tank.

• Point the manual gun (K4) into a container (K5), drain the residual paint and wait for the washing fluid to come out clean.

• As the pump starts idling, reduce pressure to the mini-mum (turn counterclockwise the pressure control knob (K1)), press the OFF (0) switch to disengage the pump from the engine and stop the engine.

• Perform the wahing of the guns.

• In case of long prolonged downtime, we recommend you to suck and to leave light mineral oil inside the pumping group and the flexible hose.

• From the control panel, set the MENU 1 operation of the right and left guns simultaneously.

• Move the control lever to position "MAN" and drain any residual paint. Wait for the cleaning liquid to come through clean.

• Remove all clearing liquid from the tank and turn the machine off.

• Turn the pressure adjustment knob (K1) to minimum (pump stopped).

ROUTINE MAINTENANCE

TOP UP HYDRAULIC OIL

With each start up, check the hydraulic oil level by looking through the gauge on the side of the hydraulic body. If necessary, use “hydraulic oil type AGIP OSO Li/46 code 150/L” to top up the level.

RELEASE THE SUCTION VALVE

In case of pump failure, release the suction valve fitted on the head of the pump in the following way: • Remove the suction hose fitting and release the valve by

inserting a rigid rod (M1) with a diameter lower than 15 mm.

M

21

English

VIKING LINER

Oil max level

CLEANING THE COMPRESSION VALVE

When the compression valve must be removed, clean it with specific solvents according to the type of paint used and refit all parts by inverting the disassembly order.

REPLACING THE HYDRAULIC OIL

After operating for 100 hours, replace the oil in the pump; • Discharge the waste oil through the hydraulic filter fitted at

the bottom of the pump casing.

• Clean and, if necessary, replace the worn seals.

• Replace the filter in its seat by screwing it tightly.

• Fill the pump with the recommended oil until it reaches the maximum level.

• Then, replace the oil every 250 hours.

DESCRIPTION OF CONTROLS

N1) Directional lever Pull on the lever to release the linear drive lock (a) and allow

the machine to perform curved line tracts.

N2) Advancement

N3) Accelerator It gradually sets the number of revolutions of the internal

combustion engine.

N

N1

a

N2

N3

MOTOR OIL CHECK

Every 100 hours check the oil level through the dedicated oil plugs on the base of the engine.Refil the oil level if necessary.

22

Engl

ish

VIKING LINER

FORWARD BACKWARD

N7

N6 N4

N4

N8

N11

N13

N10

N14

N9

N12

N5

N 4) Direction selector It allows the user to select the machine advancement

direction; if pressed, it stops the machine movement.

N 5) Electric brake release When pressed, it allows the machine to be pushed in the

event of electrical failure or lockage.

N 6) Light switch It activates/deactivates the frontal spotlight (if installed).

N 7) Spraying by pressing it, the manual spraying is enabled.

N 8) Indicator It displays the battery charge status.

N 9) Red light selector It lifts or lowers the spray unit’s stabilizing wheel.

N 10) Speed regulation handle It allows the user to gradually regulate the machine’s

advancement speed.

N 11) Blue light selector It activates the oil cooling fan.

N 12) Blue light selector It activates the pneumatic circuit’s compressor.

N 13) Green indicator light When on, it indicates that the machine is ready for operation

N 14) Alternator When the red indicator is on, it indicates a failure of the

alternator employed for charging the batteries.

23

English

VIKING LINER

TROUBLESHOOTING

SolutionCauseProblem

O

• Engine won't start

• WARNING : For further solutions to engine problems

please see the enclosed "Lombardini" instruction manual.

• The equipment does not start

• The equipment does not suck the product

• The equipment sucks but it does not reach the pressure desired

• When pressing the trigger, the pressure lowers considerably

• The pressure is normal but the product is not atomized

• The atomization is imperfect

• When releasing the trigger of the gun, the equipment does not stop

• The fuel manifold is closed;

• Engine is out of gas;• Cold engine;

• Spark plug cable is disconnected or damaged;

• On/Off switch disconnected;

• breakdown of pressure transmitter;• breakdown of motor electric control

box;• The line of material coming out of the

pump is already under pressure;• The product is solidified inside the

pump;

• Suction filter clogged;• Suction ilter too fine;

• The equipment sucks air;

• Lack of product;• The equipment sucks air;• The drain valve is open;• Suction or delivery valve dirty;

• Nozzle too big or worn;• The product is too dense;• The filter of the gun-butt is too fine;

• The nozzle is partially clogged;• The product is too dense;• The filter of the gun-butt is too fine;

• The nozzle is worn;

• Suction or delivery valve dirty;

• Drain valve defective;

• Switch the fuel manifold to "Open" position;

• Refill gas tank;• Switch the Start lever to MAx posi-

tion;• Connect or replace the cable;

• Ensure the On/Off switch is on the “on” position and turn clockwise the pressure control knob;

• verify and replace it, if necessary;• verify and replace it, if necessary;

• Open the drain valve to release pressure in the circuit;

• Open the drain valve to release pressure in the circuit and stop the machine. Disassemble the pumping group and the pressure transmitter and clean;

• Clean or replace it;• Replace it with a larger-mesh filter

(with very dense products, remove the filter);

• Check the suction pipe;

• Add the product;• Check the suction pipe;• Close the drain valve;• Disassemble the pumping group;

• Replace it with a smaller one;• Dilute the product, if possible;• Replace it with a larger-mesh filter;

• Clean or replace it;• Dilute the product, if possible;• Replace it with a larger-mesh filter;

• Replace it;

• Disassemble the pumping group and clean;

• verify and replace it, if necessary;

24

Engl

ish

VIKING LINER

P2

OFFIf the equipment is still under pressure after per-forming the operations above described because of the nozzle or the flexible hose clogged, proceed as follows:• Loosen very slowly the gun nozzle. • Release the safety clamp.• Point the gun towards the collecting container

of the product and press the trigger to release pressure.

• Loosen very slowly the connection fitting from the flexible hose to the gun.

• Clean or replace the flexible hose and the nozzle.

P1

CORRECT PROCEDURE OF DECOMPRESSION

MANUAL GUN• Lock the safety clamp (P1) of the gun.

• Push the OFF button (P2) switching the machine off.

• Unlock the safety clamp (P1).• Place under the gun the paint collecting tank. At the end lock the safety clamp again (P1).

AUTOMATIC GUN• Press the switch (P5) to spray the product and discharge the

residual pressure from the automatic guns.• Turn the levers (P3) and (P4) to release residual pressure.

P

P3

P4

P5

25

English

VIKING LINER

SPARE PARTSSPARE PARTS

COMPLETE HYDRAULIC BODY

Page 30

UCOMPLETE COLOUR BODY

Page 32

V

COMPLETE COLOUR BODY

Page 32

V

COMPENSATION VALVES

Page 28

S

HIGH PRESSURE GUN AT 250

Page 26

INTERNAL COM-BUSTION MOTOR

Page 34

Q

W

SUCTION SYSTEM

Page 29

T

LA95 GUN EXPLO-DED VIEW

R

26

Engl

ish

VIKING LINER

Components Pos. 5 - 11023 - Linkage 11005/3 ball 11204/1 ball housing 11205/2 Spring 11205/4 Linkage 11205/5 Sleeve 11205/6 Manifold sleeve 11205/7 bush

HIGH PRESSURE GUN AT 250

Pos. Pos.

Super Fast Clean nozzle

Super Fast Clean body

Super Fast Clean gasket

Sleeve

Hand guard +

3 TSP 3x8 screws

Complete linkage rod

Complete trigger

Safety lever

brake washer

Trigger

Pin

Pin

Pin

Spray gun body

Plug

Plate

M5 self-locking nut

Copper gasket

Filter

Handgrip

Spring

Copper gasket

M16x1.5 articulated joint

1/4” articulated joint

vedi tab.*

18270

18280

11004

11006 +

11032

11203

11008

11010

11011

11014

11012

11013

11034

11206

11207

11208

11209

11020

-

11018

11017

32010

11015

11155

A

1

2

3

4

5

6

6a

6b

6c

6d

6e

6f

7

8

9

10

11

12

13

14

15

16

Code Description Code Description

A

1

2 3

4

6

12

5

116a

6b

6c 6d6e

7

89

10

13

14

15

16

6f

Q

27

English

VIKING LINER

WARNING: Always indicate code and quantity for each part required.

EXPLODED VIEW GUN LA 95 RIF. 23340/4

25

26

27

1113

15

17

15

9

8

7

30

29

28

10

14

20

21

2223

24

12

19

16

18

19

2

3

1

Pos.

Super Fast Clean bodySuper Fast Clean Super Fast Clean gasketsSleeveWasher PunchGun bodyGaskets stuffing ringGasketGaskets stuffing screwM3 nutWasherO-ringPistonO-ring

Code Description

123789101112131415161718

Q.ty

11111111111211 1,

Pos. Code Description Q.ty

19202122232425

262728293031

Self-blocking nutSpringScrewback tapO-ringAdjusting knobFemale couplingMale couplingNutScrewWasherNippleCylindric fittingNozzle fitting

21111111111111

18270See table*18280110043300711705117111171211114117139000251171432015/31172111105

1102711108117151171633013/711717117181172052017340083301232891171915002

R

28

Engl

ish

VIKING LINER

11

COMPENSATION VALVES

Pos.

Compensation valves33711

Code Description

S

29

English

VIKING LINER

3

4 1

2

SUCTION SYSTEM

Pos.

Suction system

Suction tube

Recirculation hose

Clamping spring

Suction filter

16690

16607

16609

18095

16802

1

2

3

4

Code Description

T

30

Engl

ish

VIKING LINER

COMPLETE HYDRAULIC BODY

527

6

54

31

49 51

5046

4748

53 19 2018

141217

98 10

13 15 16 17

21 22 23 2425

26 2728 29

30

2

3133 34 35 32

38 37 36

39404142

44 43 45

U

31

English

VIKING LINER

* 33002 Complete diaphragm

Pos. Pos.

Hydraulic body with sleeve

Filter assembly

Piston insert

Nut

Spring

Oil distributor

Diaphragm

bearing

Elastic ring

Eccentric shaft

Eccentric bearing

Elastic ring

Spacer

Elastic ring

bearing

O-ring 4625

Cover

Nylon washer

Screw M6x25

Inspection plug

O-ring 2021

60 MESH sieve filter

Copper washer 18x14,5x1,5

Oil filter body

Oil tap 3/8"

Sleeve nut

Spring

Washer

Elastic ring

Piston

Oil tap

High temperature 28x38x7 Corteco

Screw M3x8 UNI 5931

Tab

Pulley

Elastic ring

Dampers

Half-joint

Tab UNI 6604

Dowel

Spacer

Spline M12

Waher type SCHNOOR ø12

Nut M12

Electric motor 220v/50Hz

O-ring 9,8x1,5

valve body

Polypropylene retainer

Dowel M5x12 2K

Spring

Knob

Diaphragm insert

Pressure valve assembly

18711/1

12475

32033

91026

33002/3

33002/2

33002/1

31125

81020

18712

18725

12470

18715

8007

18728

18726

18713

12462

31106

32007

32012

258

32010

12461

32108

32041

32022

32021

32020

32019

82005

31128

9308

18716

18714

12470

81038

12460

81014

81009

18718

81012

95114

81010

81001

32014

32155

32016

32017/1C

32017/2

32017

33003

32150

1

2

3

4*

5*

6*

7*

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53


32

Engl

ish

VIKING LINER

1514 13

121110 9

8 765

23

1

191817

20

23

24

182122

164

26

27

2829

30

313233

25

V COMPLETE COLOUR BODY

33

English

VIKING LINER

Pos. Pos.

Complete colour body

Right colour body casting

Left colour body casting

Ø16 copper washer

High pressure hose fitting

Complete suction valve

Gasket

Complete spear valve

Spear valve seat

valve body

Spear valve guide

Spring

Ø6,3 washer

Self-locking nut

Inlet liner

Ø10 SCHNORR washer

10x55 TCE screw

Complete return tap

Nipple

1/4" copper washer

O ring

Return tap

3/8"x1/4" nipple

3/8" copper washer

Pressure gauge

Pressure gauge gasket

Complete drain valve

Sealing plug

Copper seal

Spring

Spring seat

Ø11 ball

ball seat

ball seat fitting

Gasket

33000

33001Dx

33001

33007

33006

33017

33018

33019

33020/1

33020

33021

33022

33023

33024

96099

33005

33004

33016

33015

33012

33013/3

33013

33011

33010

33008

33009

33033

33032

33031

53006

33029

33028

33027/2

33027/1

33026

1

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33


34

Engl

ish

VIKING LINER

1

871516

1314

1112

910

87

654

32

INTERNAL COMBUSTION MOTOR

Pos. Pos.

Petrol motor

Motor flange

Screw

Motor pinion

Washer

Screw

Screw

Washer

Plate

Crown gear

bearing

Corteco

Washer

Screw

Reduction box

Tab

4415

12478

32004

31116

31115

69011

4019

32028

31111

31110

42255

31128

54003

31106

31107

31166

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16


W

35

English

VIKING LINER

X1 X1

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

01-01-09 LARIUSSet: 0 Att: 0

®

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

SETTINGS1. Set Date

®

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

SETTINGS2. Setup Time

®

Fig.1

MENU key

SELECT key

VIKING LINER CONTROL PANEL USE

• Activate by means of dedicated switch “0-1” on the right side of the control panel;

• The display shows date, time and temperature (see Fig.1);• Press the menu key to scroll through the list of functions from

1 through 9.Display when the electronic box is switched on

MENU 1: SETUP DATE Press the “MENU” key and the first setting “1. DATE” will appear. To change the date:• Press the “SELECT” key to enter the page;• Press “MENU” to change the numbers for the date;• Press “SELECT” to shift from day to month and to year;• Press “SELECT” from the year position to return to point “1.

DATE".Press “MENU” to go on to point 2.

MENU 2: SETUP TIMEWhen “MENU” is pressed from point 1, the display shows “2. TIME”. To change the time:• Press the “SELECT” key to enter the page;• Press “MENU” to change the numbers for the date;• Press “SELECT” to shift from hour to minutes and seconds;• Press “SELECT” from the second position to return to point

“2. TIME”.Press “MENU” to go on to point 3.

Discharge pressure turning the knobs (X1).

X

36

Engl

ish

VIKING LINER

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

SETTINGS3. Main hours

®

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

SETTINGS4. Main. Alert

®

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

SETTINGS5. Main. done

®

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

SETTINGS6. Totals

®

MENU 3: SETTING MAINTENANCE HOURS When “MENU” is pressed from point 2, the display shows “3. MAINTENANCE HOURS”. This menu is used to set the n° of hours between successive maintenance tasks. To change the time:• Press the “SELECT” key to enter the page;• Press “MENU” to increase the time set. Hold “MENU” down

and press and release “SELECT” to invert the counter and therefore reduce the time set ;

• Press “SELECT” again to return to point “3. MAINTENANCE HOURS”.

Press “MENU” to go on to point 4.

MENU 4: MAINTENANCE ALERT When “MENU” is pressed from point 3, the display shows “4. MAINTENANCE ALERT”. This menu is used to set the n° of hours prior warning for maintenance tasks. To change: • Press the “SELECT” key to enter the page;• Press “MENU” to increase the time set. Hold “MENU” down

and press and release “SELECT” to invert the counter and therefore reduce the time set;

• Press “SELECT” again to return to point “4. MAINTENANCE ALERT”.


MENU 5: MAINTENANCE DONEWhen “MENU” is pressed from point 4, the display shows “5. MAINTENANCE DONE”. This menu is used to reset the countdown after having completed maintenance. To change: • Press the “SELECT” key to enter the page;• Press “SELECT” again to confirm that maintenance has

been done. The display automatically goes back to menu “5. MAINTENANCE DONE”.


MENU 6: TOTALS When “MENU” is pressed from point 5, the display reads “6. TOTALS” This menu shows the number of hours worked and the number of times the pump control clutch has been activated. • Press the “MENU” or “SELECT” key to return to “6. TOTALS”. Press “MENU” to go on to point 7.

37

English

VIKING LINER

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

SETTINGS7. Language

®

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

SETTINGS8. Sequencer

®

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

SETTINGS9. Return

®

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

SPRAY MENU1. Manual Command

®

MENU 7: LANGUAGE When “MENU” is pressed from point 6, the display shows “7. LANGUAGE”. This menu can be used to set the language. • Press the “SELECT” key to access the page, and the “MENU”

key to switch from Italian to English and from English to Italian;• Press “SELECT” to return to “7. LANGUAGE”. Press “MENU” to go on to point 8.

MENU 8: SEQUENCER When “MENU” is pressed from point 7, the display shows “8. SEQUENCER”. This menu can be used to select or deselect the use of the automatic tracker. • Press the “SELECT” key to access the page, and the “MENU”

key to switch from sequencer YES or NO ;• Press “SELECT” to return to “8. SEQUENCER”. Press “MENU” to go on to point 9.

MENU 9: RETURNWhen “MENU” is pressed from point 8, the display reads “9. END”. This menu is used to go back to the initial page. • Press the “SELECT” key to return to the home page.

MENU 1: MANUAL COMMANDThis function allows one to decide which gun to use with the control lever in the “continuous” position. The possibilities are:

• Left gun only;• Right gun only;• Right and left guns and simultaneously;• Press the menu button to change setting;• Press the select key to exit.

Note: this menu refers only to the “MANUAL” (“MAN”) line.

LINE SEQUENCING FUNCTION

From the home page, keep the “MENU” key pressed for more than 2 seconds to enter the line programming mode. (Note. Only if Menu 8 was previously set to “Sequencer ON”).

If “Sequencer YES” is selected, it is possible to enter the dotting setting menu described below.

Y

38

Engl

ish

VIKING LINER

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

SPRAY MENU2. Right Line

®

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

SPRAY MENU3. Right space

®

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

SPRAY MENU4. Left Line

®

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

SPRAY MENU5. Left space

®

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

SPRAY MENU6. Start left space

®

MENU 2: RIGHT LINE This function allows the programming of the length of the dashed line.

• Press menu key until page 2 is displayed;• Press select key to enter the page;• Press the menu key to increase the set value;• Hold “MENU” down and press and release “SELECT” to invert

the counter (and therefore reduce the value set). • Press select to exit.

MENU 3: RIGHT SPACEThis function allows the programming of the length of the blank area between dashes.



MENU 4: LEFT LINEThis function allows for the programming of the length of the dashed line.



MENU 5: LEFT SPACE This function allows for the programming of the length of the blank area between dashes.



MENU 6: START LEFT SPACEThis function allows for the spray delay to be set exclusively for the left gun.

39

English

VIKING LINER

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

SPRAY MENU7. Command

®

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

SPRAY MENU8. Distance

®

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

SPRAY MENU9. Step Lenght

®

WWW.LARIUS.COM

HEAD LINER CONTROL

SELECT

MENU

SPRAY MENU10. Return

®

MENU 7: AUTOMATIC SPRAY COMMAND This function allows to set the guns to be used with the lever in the “AUTOMATIC” (“AUT”) position.• Press menu key until page 7 is displayed;• Press the select key to enter the page.Possible settings are:• Left gun off + Right gun dashed;• Left gun off + Right gun continuous;• Left gun dashed + Right gun dashed;• Left gun dashed + Right gun continuous;• Left gun continuous + Right gun dashed• Press the menu key to choose the desired setting;• Press select to exit.

MENU 8: DISTANCE This function allows to set the distance of work before the sprayer stops.

• Press menu key until page 8 is displayed;• Press select key to enter the page;• Press the menu key to increase the set value;• Holding down the menu key, press and release the select

key to decrease the set value;• Press select to exit.

N.B.: the value “0” disenables the control.

MENU 9: STEP LENGHTThis function is used to correct any errors that may occur between the dotted line entered and the line actually made.• Press the “MENU” key until page 9 is displayed;• Press the “SELECT” key to enter the page;• Press the “MENU” key to increase the value set (the line

length is reduced);• Hold “MENU” down and press and release “SELECT” to invert

the counter (and therefore reduce the value set). The length of the line increases;

• Press “SELECT” to exit.

N.B.: the step length is already set in the factory and generally does not need to be changed.

Once the various options have been set, it is possible to shift from the manual to the automatic spraying by simply changing the position of the control lever: AUT = AUTOMATIC (works using the settings in menu “2. LINE”, “3. SPACE” and "7.COMMAND"). MAN = MANUAL (works using the settings in menu “1. MANUAL COMMAND”).

MENU 10: RETURNThis function is used to go back to the home page.

• Press the “MENU” key until page 10 is displayed;• Press the “SELECT” key to return to the home page.

40

Engl

ish

VIKING LINER

2 MT

1 MT 2 MT0,5 MT

2 MT

1 MT 0,5 MT

1 MT

RIGHT

LEFT

1 MT

0,4 MT 2,6 MT0,3 MT

1 MT

0,4 MT 0,3 MT

2 MT

SPACE AND LINE SETTINGS

• Possibility of programming the RIGHT SPACE and RIGHT LINE, LEFT SPACE and LEFT LINE independently.

• Set the DELAY SPRAYING parameter of the LEFT gun. The DELAY SPRAYING of the LEFT gun is read only once by

the program upon enabling of the spray control lever (AUT).

The SPACE and LINE measurement settings for the left and right guns have been taken to the second decimal resolution.Values of the following type can therefore be set: MT 1.54.

Example of programming to obtain the spray shown in "Figure 1"

RIGHT line 2 MT

RIGHT space 1 MT

LEFT delay spray 0,5 MT

Control LH=T RH=T

LEFT line 1 MT

LEFT space 2 MT

Figure 1


RIGHT line 2 MT

RIGHT space 2 MT

LEFT delay spray 0,3 MT

Control LH=T RH=T

LEFT line 0,4 MT

LEFT space 2,6 MT

Figure 2

Z

RIGHT

LEFT

41

English

VIKING LINER

1 MT 1 MT1 MT

1 MT 1 MT

1 MT 1 MT1 MT

Programming of other spray types has remained unchanged.


RIGHT line 1 MT

RIGHT space 1 MT

LEFT delay spray 0 MT

Control LH=T RH=T

LEFT line 1 MT

LEFT space 1 MT

Figure 3


RIGHT line 1 MT*

RIGHT space 1 MT*


Control LH=T RH=C

LEFT line 1 MT

LEFT space 1 MT

Figure 4

**Not considered as the RH gun is in continuous mode


RIGHT line 1 MT

RIGHT space 1 MT


Control LH=T RH=T

LEFT line 0,5 MT

LEFT space 1,5 MT

Figure 5

RIGHT

LEFT

RIGHT

LEFT

RIGHT

LEFT

42

Engl

ish

VIKING LINER

ACCESSORIES

Art. 11220: AT 250 1/4+baseArt. 11221: AT 250 M16x1,5+base

WARNING: Always indicate code and quantity for each part required

PISTON GUNSTOCK FILTERSArt. 11039: Green (30M) - Art. 11038: White (60M)Art. 11037: Yellow (100M) - Art. 11019: Red (200M)

Art. 0147:MANOMETER

Art. 96200:COMPLETE LINE FILTER

HIGH PRESSURE PIPESØ 3/16 - 1/4 - 3/8

Art. 16685:SUCTION DISPERSIONSYSTEM

Art. 95218: 30 MESH FILTERArt. 95219: 60 MESH FILTERArt. 95220: 100 MESH FILTERArt. 95221: 200 MESH FILTER

Code 11135: L91x 1/4+baseCode 11136: L91x M16x1,5+base

Code 11080: AT 300 1/4+baseCode 11081: AT 300 M16x1,5+base

AA

43

English

VIKING LINER

Art. 4038: LASER POINTER Art. 217560: Mx 1000 E

Art. 4506: ADJUSTAbLE SPOTLIGHT

Art. 4720: SEAT KIT

Art. 4507: FLASHING LIGHT

Art. 26000: OPERATOR FOOTbOARD

44

Engl

ish

VIKING LINER

Code 4405:REFLECTING PEARLS TANK WITH DISPENSER

Code 4500:MICROSPHERES DISPENSER

Art. 18270: SUPER FAST-CLEAN base UE 11/16x16

Art. 18280: GASKETS

SUPER FAST-CLEAN TIP

SUPER FAST-CLEAN

Nozzles code

SFC07-20SFC07-40SFC09-20SFC09-40SFC11-20SFC11-40SFC13-20SFC13-40SFC13-60SFC15-20SFC15-40SFC15-60SFC17-20SFC17-40SFC17-60SFC19-20SFC19-40

SFC19-60SFC21-20SFC21-40SFC21-60SFC23-20SFC23-40SFC23-60SFC25-20SFC25-40SFC25-60SFC27-20SFC27-40SFC27-60SFC27-80SFC29-20SFC29-40SFC29-60

SFC29-80SFC31-40SFC31-60SFC31-80SFC33-40SFC33-60SFC33-80SFC39-40SFC39-60SFC39-80SFC43-40SFC43-60SFC43-80SFC51-40SFC51-60SFC51-80

Nozzles code

TSC 07-20TSC 07-40TSC 09-20TSC 09-40TSC 11-20TSC 11-40TSC 13-20TSC 13-40TSC 13-60TSC 15-20TSC 15-40TSC 15-60TSC 17-20TSC 17-40TSC 17-60

TSC 19-20TSC 19-40TSC 19-60TSC 21-20TSC 21-40TSC 21-60TSC 23-20TSC 23-40TSC 23-60TSC 27-20TSC 27-40TSC 27-60TSC 31-40TSC 31-60

From size 7-20 to 31-60

TOP SPRAYING CLEAN

45

English

VIKING LINER

TUBES MANUAL WINDER3/16" - 3/8" - 1/4" max width mt. 20

COMPLETE FAST-CLEAN ExTENSIONArt. 170: cm 30

Art. 171: cm 60 - Art. 172: cm 100

PLA 1/4”+ FAST-CLEAN WITH NOZZLE

Art. 11420-11425-11430: cm 130-180-240

PLA M16x1,5+ FAST-CLEAN WITH NOZZLE

Art. 11421-11426-11431: cm 130-180-240

GUN ExTENSIONArt. 153: cm 30

Art. 155: cm 60 - Art. 156: cm 100

Art. 16780: TELESCOPIC PAINT ROLLERGun 220 bar

Extension 1300 - 2000 mm

PLAArt. 11400: cm 130

Art. 11401: cm 180 - Art. 11402: cm 240

Due to a constant product improvement programme, the factory reserves the right to modify technical details mentioned in this manual without prior notice.

LINE STRIPERS

LARIETTE LINER 2000

LINER 3000

K2 LINER

EvEREST TH SELF-PROPELLED

DALÌ LINER

LARIETTE SPORT

ExCALIbUR LINER

DRAGON LINER SELF-PROPELLED

23801 CALOLZIOCORTE - LECCO - ITALY - Via Antonio Stoppani, 21Tel. (39) 0341/62.11.52 - Fax (39) 0341/62.12.43E-mail: [email protected] - Internet http://www.larius.com

MANUFACTURER:

DIRECT LINE

Tel. (39) 0341/621256Fax (39) 0341/621234

CUSTOMERS TECHNICAL SERvICE

06 - 11 engnlishnldo - lariuslarius.org/manuali/vikingline_uk.pdf · in any case, cleaning, ......

Documents