i:-======---- - - --------------.;;.....;;;.....;;..;=._.=:.;..::..,;=...,;=...,;=...,;=...,;=.-=-~-=--=--=--~-~--_ ---.::::. -_ -_ -_ -_ -_ -=========::::=::===============================:::i FAULT FINDING

Cure Symptom Possible Fault --+--------No light No Lamp

Faulty Lamp No Power

Shutlers Fully in

Lamp chassis nol seated

Uneven Light Lamp Adjustment

MAINTENANCE

knob moved ·

Lamp not fully sealed in holder

Relleclor selling

Fil Lamp Fil new lamp Check supply and · spollighl cable

Extend shutlers

Remove and re-insert

Check lamp adjustment Check lamp in lampholder. observing salety precautions

Check

Open lamp chassis observing safety precautions . Clean ~he rolloctor through the bottom of the lamphouse with the tube removed using a slightly damp cloth to which a little detergent h3Sbeenadded . · Lenses should be cleaned with a damp cloth only. Periodic inspection should be carried out, of the lampholder und cable . Any components showing wear or damage should be replaced immed iately. Contact your CCT representative for list of spare parts available.

. CALJTION Damaged lenses or UV safety screens MUST be replaced befor_e luminaire is used . (a) When replacing or adjusting a lamp, the product , with particular attention to all internal and external wiring, should be inspected and any faults corrected . (b) At least once every twelve months the product. if portable, should be bench inspected for electrical and m1:chanical wear and damage . If not portable this inspection should be carried out jn situ . (c) Depending upon usage , internal and external wiring will deteriorate in time and should be replaced al the first indication of wear or aging . ' (d) Product can be returned to any CCT service representative for repa ir and or maintenance . Spare and replacement parts can be supplied for use by other compentent service Finally ... CHECK CABLE AND PLUG FOR ANY SIGNS OF DAMAGE REPLACE DAMAGED PARTS IMMEDIATELY.

CCT Theatre Lighting Limited, is constantly developing, improving and changing its product line. All descriptions and specifications In this publlcallon present only general particulars and sha.D not form any part of any contract . Toe right is reserved to change the spocification without prior notification . 1

ACCESSORIES ZS039 Fast Fit Lamphouse accessory · ZS040 Fast Fil Lens tube accessory ZS04 i Fast Fit · X' Lens Tube accessory 20016 Df:--ip-in Iris Z0017N Bait In Iris/Blackout 20120 Rota Gobo Holder Z0121 Standard Gobo Holder Z0013 Extra Colour Filter Frame tor ZOwi-iiP Lens Tubes Z0014 Extra Colour Fitter Frame for ZOOOQ/RfT/ Lens Tubes Z0015 Extra Colour Filter Frame tor ZOOOSN Lens Tubes Z0083 Hook Clamp zooas Safley Chain Y0057 Spigot

For complete detai ls of colour change accessories suitable tor the SIihouette Range see colour change data sheet.

C:C:T dlighting WINDSOR HOUSE, 26 WILLOW LANE, MITCHAM,

SURREY, CR4 4NA. UK. TEL: 081-640 3366 TELEX: 946648 FAX UK: 081-648 5263 FAX INT: 441-648 5263

J

C:C:T jlightiing USE.R INFORM/.\ 1-ION Leal let ref : WO\U\O

~O~m)(Q)(l)]@~~® ~@@M [p)f@iro~® ~[p)@i~o@[n)~ Base Down Lamp 1000/1200W Order Code ZOOAO /N/P/Q/X/S/TN

. 220/240V ONLY WARNING - BEFORE U~E :-(a) Read CCT Lighting User Information General leaflet. (b) Read these ins1ructions.

Jan ·90

(c) Inspect product tor damage upon removal from its carton . (d) Ensure that external supply wiring and socket (if to be used)

Is property installed and protected .

11-llS INFORMATION IS GIVEN IN THE B'=ST INTERESTS OF: Safety, Hanc:ing, Installation, Use and Maintenance of products solp by CCT lighting . Instructions relevant to each product will be found In the carton in which the product is supplied . They must be carefully read before any attempt is made to use and/or install the product. The ins1ruc­lion sheet should be retained for further reference . Additional copies are available on request. In the UK, ins.allers and users are obliged under the "Health and Safety at Work Act" to ensure that they are acquainted with information s;ipplied with the product and are fully aware of any precautions t:1at need to be taken. CCT produc:s are designed to conform to the requirements of UK law and to tha requirements of relevant national and international standards.

SPECIAL NOTE CCT products should not be modttied. Any modttlcatlon may renderthe product unsafe andwill Invalidate any safety/approval marks. CCT Theatre. Uqhtlng Llmited, .will not accept any respon. sibllity for any damage caused as a result of their modttlcatlon .

INSTALLATION Installation of CCT products should be carried out only by competent persons in accordance with instructions supplied with the tuminairn and/or accessory . If in any doubt, consult a suitably qualttied person.

LAMP FITTING Suitable tamps - Base MUST be GX9.5 220/240V HJOOW T/11, T/19 or equivalent Damaged er thermally deformed lamps MUST NOT be used . Lamp manufacturers instruct10ns must be followed at all times .

/!''\, [w ARNING I /f\. -Never attempt to Insert a lamp with the spotlight connected lo a

· dimmer circuit or lo mains. Before opening the spotllghl unplug the power cable. Failure to observe this precaution :

MAY RESULT IN SEVERE BURNS. Do not touch the lamp surface - use the disposable glove or shield provided with the new tamp when fitting it Into the lampholder. When changing a recerrt!y failed tamp, allow time for the lamp and condenser lens lo cool before removing it from the spotlight.

When supplied the lampholder Is set for uso with a 1 OOOW lamp order to re-set for 1200 Watt lamp adjust as follows .

Remove screws and spacers (a). Lift lampholder (b). Re-frt lampholder lixing screws with spacers below lampholder fixing slots (c).

1000W 1200W . Lampholder setting Lampholder setting

Note that :lamptray slide is engraved with centre line. Always ensure that centre of lamp filament lo be used coincides with this mark. If it does not, reset lampholder as instructed above.

LAMPHOUSE The Silhouette ZOOAO base down lamp 1000/1200W lamphouse lamphouse is part of a range which Includes :-ZOOFO 1 OOOW Axial tamp lamphouse ZOODO 2500W Base Down Lamphouse ZOOBO 2000W Base Down Lamphouse

Beam TIit Angle 90° - 0 - 70°

FfTTING LENS TUBE (a) Select desirer! tube . (b) Decide whether lens knob/s are to be above or below tube when In use (except • X' tube) (c) Attach tube to lamphouse with 4 off M5x20 Allen bolls and key provided . (d) Decide whether front colour frame/ accessory cassette Is lo be arranged for lop or side entry. Adjust as necessary with 4 off M5x8 screws holding cassette to lens tube. (e) Suspension Yoke should be attached :-With ZOOON, ZOOOP and ZOOOX Tubes to the tamphouse . With other tubes directly to the tube via support bracket. Select for best balance . Note that Yoke has optional holes for height selection .

seleclion holes

Gale lor -c....,,.~1- drop -in Iris or

Gobo holder

The Z00017N Iris Blackout, when used, is located behind the shutter set.

LENS TUBES

f.JlQ I . ; ~ --.. -'--'

ZOOON dQ ZOOOP 30 zooox 15-32 31° -H· Zoom 19• -d0° Zoom-r 15• -32° Zoom

,. "

" .. CJOLJ zoooo 15 13• -23° Zoom

" r--r-,00:i I ~ I ' I • L.--l

, , .. r·-,~·· I '• I lr L •• _J

[)clQ zooos 10 g• -2 f • Zoom

ZOOOT 8 a• Non-Zoom

zooov 5 5°Non-Zoom

FlrllNG PLUG A suitable plug of al leastl15A(220/240V) rating should be fit1ed tc the srotlight power cable, observing the connection colour code as follows:

MOUNTING

LUMINAIRE MAXIMUM SURFACE TEMPERATURE (Msn Maximum ar steady state 1so0 c ta 45°c

FOCUS AND LAMP AJUSTMENT With the exception of ZOOOT and ZOOOV the lens system allows vc1riable zoom beam spread and should be used to set the required boam size, before trimming with the shutters or the Iris. (a) With shutters/iris fully open slacken lens knobs and slide adjust to maximum acceptable beam size/hardness. Tighten lens knobs. (With a new lamp, socket support trim screws should be adjusted to centralise filament. (b) By means of shutters/Iris adjust gate size as required . (c) If a Gaba is being projected, lenses and shutters can be trimmed for image size and definition.(see also d.) (d) Trim lens and reflector settings for optimum performance• by adjusting contfol knobs. Ensure they are fully finger tightened when setting has been completed . • Peaky or flat field, Minimum/maximum brightness, Sort/hard focu

flea,, froo1 lEllS KNOBS

D WARNING j

3-Sm ------- ,

M1n1mum d-s tanc! from lighted obiect w,th 10- leris twor sl Ji1U;,honl