275261 - officemax · use standard safety precautions for finely divided powders. thermal...

MATERIAL SAFETY DATA SHEET

#1108 #1201

POVIDONE IODINE SWAB/SCRUB/OINTMENT/PREP/SOLUTION

Section I -- General Information

Product/Trade Name: Povidone Iodine Swab/Scrub/Ointment/Prep/Solution

Manufacturer's Name: PDI-Professional Disposables Inc.

The Healthcare Division of Nice-Pak Products, Inc.

Manufacturer's Address: 2 Nice-Pak Park Orangeburg, NY10962-1376

Hazard Rating (NFPA): Health: 1

Flammability: 1

Reactivity: 0

Specific: None

Emergency or Information Phone No.: 914-365-1700 (M-F Daytime)

At other times, contact the local Poison Control Center

Chemical Name: Mixture

Section II -- Hazardous Ingredients Per 29 CFR 1910.1200

INGREDIENTS CAS NUMBER WT. % ACGIH-TLV

Povidone Iodine Complex 2565-5418 .5 to 3 None Established

Section III -- Physical/Chemical Characteristics

Color/Appearance: Applicator saturated with dark reddish brown liquid

Odor: Faint Iodine

Boiling Point: N/A

Flash Point: >200°F

Vapor Density: N/A

Evaporation Rate: N/A

Solubility in Water: Soluble

Specific Gravity (H20=1): N/A

Section IV -- Fire and Explosion Hazard Data

Flash Point (Method Used): N/A LEL: N/A UEL: N/A

Extinguishing Media: Any

Special Firefighting Procedures: None

Unusual Fire and Explosion Hazards: May emit toxic fumes of iodine in a fire.

Section V -- Reactivity Data

Stability: Stable

Conditions to avoid: None known

Incompatibility: Alkalis and reducing agents

Hazardous Decomposition of Byproducts: Emits iodine vapors at high temperatures

Polymerization: Will not occur

Section VI -- Health Hazard Data

Effects of Overexposure:

Page 1 of 2Dynarex Corporation

9/29/2007file://C:\Documents and Settings\LJD\My Documents\Working Files11_07_06\LJD Consulting 9_06\Clien...

Skin: May cause irritation

Eyes: May be irritating

Inhalation: None

Ingestion: Harmful

Emergency and First Aid Procedures:

Skin Contact: Discontinue if rash or irritation is noted.

Eye Contact: Flush with cool water for 15 minutes.

Inhalation: None

Ingestion: Do not induce vomiting. Get medical attention.

Target Organs: N/A

Section VII -- Spill and Disposal Procedure

Spill Control: Use absorbent material and dispose per local regulations.

Waste Disposal Method: Follow local, state and federal regulations.

Handling and Storage: Avoid storing at extreme temperatures.

Section VIII -- Control Measures/Protection

Respiration: None

Ventilation: None

Protective Gloves: If handling liquid

Eye Protection: If splashing is a hazard

Hygienic Practices: Good housekeeping practices should be followed.

Other: Wear apron to protect clothing.

Section IX -- Transport/Shipping

DOT Shipping Name:

Technical Shipping Name:

DOT Shipping Classification: DOT not regulated

DOT ID Number:

DOT Label Requirements:

UN/NA Number Regulations:

Reportable Quantity:

Disclaimer:

The information furnished herein is believed to be accurate and represents the best data currently available to us. No warranty, expressed

or implied, is made and Nice-Pak Products, Inc. assumes no legal responsibility or liability resulting from its use.

Executive Headquarters: 10 Glenshaw Street, Orangeburg, NY 10962

Phone: (845) 365-8200 • Toll Free: (888) 335-7500 • (888) DYNAREX

Fax: (845) 365-8201 • Email: [email protected] • www.dynarex.com




May be used to comply with OSHA’s Hazard Communication Standard 29 CFR 1910.1200. Standard must be consulted for specific requirements.

HMIS HAZARD RATING

HEALTH 0 0 = INSIGNIFICANT 3 = HIGH FLAMMABILITY 3 1 = SLIGHT 4 = EXTREME REACTIVITY 0 2 = MODERATE TRANSPORTATION INFORMATION PROPER SHIPPING NAME Solids containing flammable liquid, n.o.s.(Ethanol) HAZARD CLASS / PKG. GRP. 4.1 / II IATA (non-canister) Special Provision A46 IDENTIFICATION NUMBER UN3175 US DOT (non-canister) Special Provision 47

SECTION 1 - PRODUCT / COMPANY IDENTIFICATION IDENTITY (AS USED ON LABEL AND LIST) Page 1 of 2 p.a.w.s. Personal Antimicrobial Wipe MANUFACTURER’S NAME EMERGENCY TELEPHONE NUMBER (24 Hours) Safetec of America, Inc. (800) 255-3924 ADDRESS (NUMBER, STREET, P.O. BOX) TELEPHONE NUMBER FOR INFORMATION 887 Kensington Avenue @ Willaim L. Gaiter Pkwy. (716) 895-1822 (CITY, STATE AND ZIP CODE) DATE PREPARED February 27, 2006 Buffalo, NY 14215 SUPERSEDES October 13, 2004

SECTION 2 - HAZARDOUS INGREDIENTS / IDENTITY INFORMATION HAZARDOUS COMPONENTS CAS # % (wt.) OSHA PEL/STEL ACGIH TLV/TWA/STEL (SPECIFIC CHEMICAL IDENTITY; COMMON NAME(S)) (OPTIONAL) PPM MG/M3 PPM MG/M3

Ethyl Alcohol 64-17-5 35 - 45 1000 (PEL) 1000 (TLV) Chloroxylenol 88-04-0 0.44 - 0.56 None Established None Established This product is not known to contain a substance subject to Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA) and 40 CFR 372 at or above minimal amounts. SECTION 3 - HEALTH HAZARD DATA ROUTES OF ENTRY - SIGNS AND SYMPTOMS OF EXPOSURE EMERGENCY AND FIRST AID PROCEDURES INHALATION: Brief (minutes) inhalation will not cause adverse effects, although, constant inhalation may cause irritation to upper respiratory tract.

Remove victim to fresh air; provide oxygen if breathing is difficult; seek medical attention if required.

EYES: Brief contact may cause mild irritation; prolonged contact may cause moderate irritation associated with redness.

Flush eyes with clear running water for a minimum of 15 minutes while holding eyelids open; if irritation persists, seek medical attention.

INGESTION: Small amounts swallowed incidental to normal handling are not likely to cause injury. Swallowing larger amounts may cause injury.

DO NOT induce vomiting; seek immediate medical attention. Vomiting may be induced only under the supervision of a physician.

HEALTH HAZARDS (ACUTE AND CHRONIC): Acute effects are possible irritation and discomfort; no known chronic effects have been established. CARCINOGENICITY NTP? No IARC MONOGRAPHS? No OSHA REGULATED? No

No additional information MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: Preexisting skin, eye, or respiratory disorders may become aggravated through prolonged exposure.

SAFETEC OF AMERICA

Form Revised 1/99

MATERIAL SAFETY DATA SHEET IDENTITY (AS USED ON LABEL AND LIST) Page 2 of 2 p.a.w.s. Personal Antimicrobial Wipe Date: February 27, 2006 SECTION 4 - FIRE FIGHTING MEASURES FLASH POINT (METHOD USED) FLAMMABLE LIMITS (% Volume in Air for Lowest Flashing Component) 97°F (TOC) LEL: 3.3 UEL: 19 EXTINGUISHING MEDIA Dry chemicals, alcohol-type or all-purpose foam, CO2

SPECIAL FIRE FIGHTING PROCEDURES Use water spray to cool fire-exposed containers and structures. Use water spray to disperse vapors; re-ignition is possible UNUSUAL FIRE AND EXPLOSIVE HAZARDS Flammable material. Toxic gases (such as carbon monoxide and formaldehyde) may be released in a fire. Concentrated vapors may

be flammable. SECTION 5 - PRECAUTIONS FOR SAFE HANDLING AND USE / LEAK PROCEDURES STEPS TO BE TAKEN IF MATERIAL IS SPILLED OR RELEASED Remove all sources of ignition. Small spills may be flushed with large amounts of water; larger spills should be collected for disposal. WASTE DISPOSAL METHODS Dispose of in accordance with Local, State, and Federal regulations. Products classified as non-hazardous may become hazardous

waste upon contact with other products. Refer to "40 CFR Protection of Environment Parts 260-299" for complete waste disposal regulations. Consult your Local, State, or Federal Environmental Protection Agency before disposing of any chemicals.

PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE Keep container(s) tightly closed when not in use. Avoid inhalation of high concentration of vapors. Store in cool, dry area away from

possible sources of ignition. Keep this and other chemicals out of reach of children. SECTION 6 - EXPOSURE CONTROLS / PERSONAL PROTECTION RESPIRATORY PROTECTION VENTILATION LOCAL EXHAUST: Required Ordinarily, none required MECHANICAL (GENERAL): Yes PROTECTIVE GLOVES EYE PROTECTION Ordinarily, none required Ordinarily, none required OTHER PROTECTIVE CLOTHING OR EQUIPMENT WORK / HYGIENIC PRACTICES Ordinarily, none required Practice safe work habits. Use according to label instructions.

SECTION 7 - PHYSICAL / CHEMICAL PROPERTIES BOILING POINT SPECIFIC GRAVITY (WATER=1) 174.6°F 0.936 VAPOR PRESSURE (mm Hg) MELTING POINT No data Not applicable VAPOR DENSITY (AIR=1) pH 1.59 (ALC.) 3.8 – 6.4 SOLUBILITY IN WATER EVAPORATION RATE (n-BUTYL ACETATE=1) Slight 1.7 (ALC.) APPEARANCE AND ODOR % VOLATILES (BY WEIGHT) Off-white; mild fresh fragrance 68.75

SECTION 8 - STABILITY AND REACTIVITY STABILITY UNSTABLE: CONDITIONS TO AVOID STABLE: XXX Extreme temperatures; sources of ignition INCOMPATIBILITIES (MATERIALS TO AVOID) Strong oxidizers; strong acids HAZARDOUS DECOMPOSITION OR BYPRODUCTS Decomposition will not occur if handled / stored properly. Thermal decomposition may emit typical products of combustion. HAZARDOUS POLYMERIZATION MAY OCCUR: CONDITIONS TO AVOID

WILL NOT OCCUR: XXX Heat The information contained herein is believed to be accurate but is not warranted to be so. Users are advised to confirm in advance of need that information is current, applicable and suited to the circumstances of use. Vendor assumes no responsibility for injury to vendee or third persons proximately caused by the material if reasonable safety procedures are not adhered to as stipulated in the data sheet. Furthermore, vendor assumes no responsibility for injury caused by abnormal use of this material even if reasonable safety procedures are followed.

MSDS PREPARED BY: Safetec of America, Inc., 887 Kensington Avenue @ William L. Gaiter Pkwy. , Buffalo, NY 14215 (716) 895-1822 Form Revised 1/99



HMIS HAZARD RATING

HEALTH 1 0 = INSIGNIFICANT 3 = HIGH FLAMMABILITY 1 1 = SLIGHT 4 = EXTREME REACTIVITY 0 2 = MODERATE TRANSPORTATION INFORMATION PROPER SHIPPING NAME Not Regulated HAZARD CLASS / PKG. GRP. None / None REF. Not Applicable IDENTIFICATION NUMBER None LABEL None Required

SECTION 1 - PRODUCT / COMPANY IDENTIFICATION IDENTITY (AS USED ON LABEL AND LIST) Page 1 of 2 RED Z™ MANUFACTURER’S NAME EMERGENCY TELEPHONE NUMBER (24 Hours) Safetec of America, Inc. (800) 255-3924 ADDRESS (NUMBER, STREET, P.O. BOX) TELEPHONE NUMBER FOR INFORMATION 887 Kensington Avenue @ William L. Gaiter Pkwy. (716) 895-1822 (CITY, STATE AND ZIP CODE) DATE PREPARED September 1, 2004 Buffalo, NY 14215 SUPERSEDES February 11, 2004

SECTION 2 - HAZARDOUS INGREDIENTS / IDENTITY INFORMATION HAZARDOUS COMPONENTS CAS # % (wt.) OSHA PEL/STEL ACGIH TLV/TWA/STEL (SPECIFIC CHEMICAL IDENTITY; COMMON NAME(S)) (OPTIONAL) PPM MG/M3 PPM MG/M3 Sodium dichloro-s-triazinetrione 2893-78-9 None Established None Established Superabsorbent polymer, CAS proprietary > 97 5 (PEL) 5 (TLV) This product is not known to contain a substance subject to Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA) and 40 CFR 372 at or above minimal amounts. SECTION 3 - HEALTH HAZARD DATA ROUTES OF ENTRY - SIGNS AND SYMPTOMS OF EXPOSURE EMERGENCY AND FIRST AID PROCEDURES EYES: May cause moderate irritation associated with redness and burning sensation.


SKIN: Prolonged or repeated contact may cause skin irritation.

Flush with clear running water for a minimum of 15 minutes; if irritation persists, seek medical attention.

INGESTION: Ingested material may cause burning of mouth, throat and esophagus, abdominal distress and moderate irritation.

Drink large amounts of water. DO NOT induce vomiting. Seek immediate medical attention.

INHALATION: Breathing of dust may cause throat and respiratory tract irritation.

Remove to fresh air; seek medical attention if required.

HEALTH HAZARDS (ACUTE AND CHRONIC): Acute effects are possible irritation and discomfort; Chronic exposure to large amounts of this material has not been characterized and the irritating properties of the material make such an exposure highly unlikely. CARCINOGENICITY NTP? No IARC MONOGRAPHS? No OSHA REGULATED? No No additional information MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: Preexisting skin or breathing disorders may become aggravated through prolonged exposure.

SAFETEC OF AMERICA

Form Revised 02/2001

MATERIAL SAFETY DATA SHEET IDENTITY (AS USED ON LABEL AND LIST) Page 2 of 2 RED Z™ Date: September 1, 2004 SECTION 4 - FIRE FIGHTING MEASURES FLASH POINT (METHOD USED) FLAMMABLE LIMITS (% Volume in Air for Lowest Flashing Component) Not Applicable LEL: Not Applicable UEL: Not Applicable EXTINGUISHING MEDIA Water, water spray, water fog SPECIAL FIRE FIGHTING PROCEDURES Use water spray to cool fire-exposed containers and structures. Wear NIOSH/MSHA approved self contained breathing apparatus. UNUSUAL FIRE AND EXPLOSIVE HAZARDS Spilled material swells and becomes extremely slippery when wet. Use standard safety precautions for finely divided powders.

Thermal decomposition may emit chlorine containing substances. SECTION 5 - PRECAUTIONS FOR SAFE HANDLING AND USE / LEAK PROCEDURES STEPS TO BE TAKEN IF MATERIAL IS SPILLED OR RELEASED In case of accidental spills, provide adequate ventilation; avoid generating dust. Vacuum (using HEPA filter equipped system) if possible to avoid

generating airborne dust. Place spilled material into a clean, dry container for disposal. Do not close disposal containers containing wet or damp material; they should be left open to disperse any chlorine gas that may form.

WASTE DISPOSAL METHODS Dispose of in accordance with Local, State, and Federal regulations. Products classified as non-hazardous may become hazardous waste upon

contact with other products. Refer to "40 CFR Protection of Environment Parts 260-299" for complete waste disposal regulations. Consult your Local, State, or Federal Environmental Protection Agency before disposing of any chemicals.

PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE Keep container(s) tightly closed when not in use. Store in cool, dry area. Keep this and other chemicals out of reach of children.

SECTION 6 - EXPOSURE CONTROLS / PERSONAL PROTECTION RESPIRATORY PROTECTION VENTILATION LOCAL EXHAUST: Recommended Use NIOSH/MSHA approved or equivalent with high

efficiency filter for particulate levels above 0.05mg/m3 MECHANICAL (GENERAL): As appropriate

PROTECTIVE GLOVES EYE PROTECTION Impervious/chemical resistant Safety glasses OTHER PROTECTIVE CLOTHING OR EQUIPMENT WORK / HYGIENIC PRACTICES Ordinarily, none required Practice safe work habits. Use according to label instructions.

SECTION 7 - PHYSICAL / CHEMICAL PROPERTIES BOILING POINT BULK DENSITY Not applicable 43.7 – 51.8 lb./cu. ft. VAPOR PRESSURE (mm Hg) MELTING POINT Not applicable >482°F (partial to full decomposition) VAPOR DENSITY (AIR=1) pH Not applicable No data SOLUBILITY IN WATER EVAPORATION RATE (n-BUTYL ACETATE=1) Slight Not applicable APPEARANCE AND ODOR % VOLATILES (BY WEIGHT) Off-white, granular powder; slight chlorine odor Not applicable

SECTION 8 - STABILITY AND REACTIVITY STABILITY UNSTABLE: CONDITIONS TO AVOID STABLE: XXX High humidity, extreme temperatures INCOMPATIBILITIES (MATERIALS TO AVOID) Strong reducing agents. HAZARDOUS DECOMPOSITION OR BYPRODUCTS Decomposition will not occur if handled / stored properly. Thermal decomposition may emit toxic substances. HAZARDOUS POLYMERIZATION MAY OCCUR: CONDITIONS TO AVOID

WILL NOT OCCUR: XXX None known The information contained herein is believed to be accurate but is not warranted to be so. Users are advised to confirm in advance of need that information is current, applicable and suited to the circumstances of use. Vendor assumes no responsibility for injury to vendee or third persons proximately caused by the material if reasonable safety procedures are not adhered to as stipulated in the data sheet. Furthermore, vendor assumes no responsibility for injury caused by abnormal use of this material even if reasonable safety procedures are followed.

MSDS PREPARED BY: Safetec of America, Inc., 887 Kensington Avenue @ William L. Gaiter Pkwy. , Buffalo, NY 14215 (716) 895-1822 Form Revised 02/2001


Form Revised 6/01/2000


HMIS HAZARD RATING

HEALTH 2 0 = INSIGNIFICANT 3 = HIGH FLAMMABILITY 0 1 = SLIGHT 4 = EXTREME REACTIVITY 0 2 = MODERATE TRANSPORTATION INFORMATION PROPER SHIPPING NAME First Aid Cream HAZARD CLASS / PKG. GRP. Not applicable REF. Not applicable IDENTIFICATION NUMBER Not applicable LABEL None Required Ground

SECTION 1 - PRODUCT / COMPANY IDENTIFICATION IDENTITY (AS USED ON LABEL AND LIST) Page 1 of 2 Safetec First Aid and Burn Cream MANUFACTURER’S NAME EMERGENCY TELEPHONE NUMBER (24 Hours) Safetec of America, Inc. (800) 255-3924 ADDRESS (NUMBER, STREET, P.O. BOX) TELEPHONE NUMBER FOR INFORMATION 887 Kensington Avenue @ William L. Gaiter Pkwy. (716) 895-1822 (CITY, STATE AND ZIP CODE) DATE PREPARED April 27, 2006 Buffalo, NY 14215 SUPERSEDES September 1, 2004

SECTION 2 - HAZARDOUS INGREDIENTS / IDENTITY INFORMATION HAZARDOUS COMPONENTS CAS # % (wt.) ACGIH TLV/TWA/STEL (SPECIFIC CHEMICAL IDENTITY; COMMON NAME(S)) (OPTIONAL) PPM MG/M3 Lidocaine HCl 50-03-3 0.5 None Established None Established

Benzalkonium Chloride 68391-01-5 0.13 None Established None Established

This product is not known to contain a substance subject to Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA) and 40 CFR 372 at or above minimal amounts. SECTION 3 - HEALTH HAZARD DATA ROUTES OF ENTRY - SIGNS AND SYMPTOMS OF EXPOSURE EMERGENCY AND FIRST AID PROCEDURES INHALATION: Unlikely route of exposure.

None expected.

EYES: Brief contact may cause mild irritation; prolonged contact may cause moderate irritation associated with redness.


SKIN: Prolonged or repeated skin contact may cause mild irritation.

Flush with clear running water for a minimum of 15 minutes; if irritation persists, seek medical attention.


DO NOT induce vomiting; seek immediate medical attention.

HEALTH HAZARDS (ACUTE AND CHRONIC): Acute effects are possible irritation and discomfort; chronic effects are possible with the ingestion of large amounts to the nervous system. Do not use on abraded skin. CARCINOGENICITY NTP? No IARC MONOGRAPHS? No OSHA REGULATED? No

No additional information MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: Preexisting skin or eye disorders may become aggravated through prolonged exposure.

SAFETEC OF AMERICA

MATERIAL SAFETY DATA SHEET IDENTITY (AS USED ON LABEL AND LIST) Page 2 of 2 Safetec First Aid and Burn Cream Date: April 27, 2006

MSDS PREPARED BY: Safetec of America, Inc., 887 Kensington Avenue @ William L. Gaiter Pkwy., Buffalo, NY 14215 (716) 895-1822 Form Revised 6/01/2000

SECTION 4 - FIRE FIGHTING MEASURES FLASH POINT (METHOD USED) FLAMMABLE LIMITS (% Volume in Air for Lowest Flashing Component) Not applicable LEL: Not applicable UEL: Not applicable EXTINGUISHING MEDIA Water, water spray, dry chemicals, chemical foam, CO2 SPECIAL FIRE FIGHTING PROCEDURES DO NOT enter confine fire space without full bunker gear (Helmet with face shield, bunker coats, gloves and rubber boots. Wear

NIOSH/MSHA approved self contained breathing apparatus. Cool fire exposed containers with water. UNUSUAL FIRE AND EXPLOSIVE HAZARDS None Known

SECTION 5 - PRECAUTIONS FOR SAFE HANDLING AND USE / LEAK PROCEDURES STEPS TO BE TAKEN IF MATERIAL IS SPILLED OR RELEASED Spills should be collected with approved inert absorbent for disposal. Use suitable disposal containers. WASTE DISPOSAL METHODS Dispose of in accordance with Local, State, and Federal regulations. Products classified as non-hazardous may become hazardous


PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE Keep this and other chemicals out of reach of children.

SECTION 6 - EXPOSURE CONTROLS / PERSONAL PROTECTION RESPIRATORY PROTECTION VENTILATION LOCAL EXHAUST: Not required Ordinarily, none required MECHANICAL (GENERAL): No PROTECTIVE GLOVES EYE PROTECTION Ordinarily, none required Not required for normal use OTHER PROTECTIVE CLOTHING OR EQUIPMENT WORK / HYGIENIC PRACTICES Ordinarily, none required Practice safe work habits. Use according to label instructions.

SECTION 7 - PHYSICAL / CHEMICAL PROPERTIES BOILING POINT SPECIFIC GRAVITY (WATER=1) No data 0.99 VAPOR PRESSURE (mm Hg) MELTING POINT No data No data VAPOR DENSITY (AIR=1) PH (1% solution in water) No data No data SOLUBILITY IN WATER EVAPORATION RATE (IPA=1) Soluble No data APPEARANCE AND ODOR % VOLATILES (BY VOLUME) White to Off-white Homogenous Cream No data

SECTION 8 - STABILITY AND REACTIVITY STABILITY UNSTABLE: CONDITIONS TO AVOID STABLE: XXX Extreme temperatures INCOMPATIBILITIES (MATERIALS TO AVOID) Strong oxidizing agents HAZARDOUS DECOMPOSITION OR BYPRODUCTS Decomposition will not occur if handled / stored properly. Thermal decomposition may produce carbon monoxide, small amounts of

nitrogen oxides, halogenated compounds or propionaldehyde may also be formed. HAZARDOUS POLYMERIZATION MAY OCCUR: CONDITIONS TO AVOID

WILL NOT OCCUR: XXX None known The information contained herein is believed to be accurate but is not warranted to be so. Users are advised to confirm in advance of need that information is current, applicable and suited to the circumstances of use. Vendor assumes no responsibility for injury to vendee or third persons proximately caused by the material if reasonable safety procedures are not adhered to as stipulated in the data sheet. Furthermore, vendor assumes no responsibility for injury caused by abnormal use of this material even if reasonable safety procedures are followed.


Form Revised 1/99


HMIS HAZARD RATING

HEALTH 2 0 = INSIGNIFICANT 3 = HIGH FLAMMABILITY 3 1 = SLIGHT 4 = EXTREME REACTIVITY 0 2 = MODERATE TRANSPORTATION INFORMATION PROPER SHIPPING NAME Solids containing flammable liquid, n.o.s. (Ethanol) HAZARD CLASS / PKG. GRP. 4.1 / II IATA Special Provision A46 IDENTIFICATION NUMBER UN3175 US DOT Special Provision 47

SECTION 1 - PRODUCT / COMPANY IDENTIFICATION IDENTITY (AS USED ON LABEL AND LIST) Page 1 of 2 Safetec Sting Relief TM - Towelette MANUFACTURER’S NAME EMERGENCY TELEPHONE NUMBER (24 Hours) Safetec of America, Inc. (800) 255-3924 ADDRESS (NUMBER, STREET, P.O. BOX) TELEPHONE NUMBER FOR INFORMATION 887 Kensington Avenue @ William L. Gaiter Pkwy. (716) 895-1822 (CITY, STATE AND ZIP CODE) DATE PREPARED February 27, 2006 Buffalo, NY 14215 SUPERSEDES September 1, 2004

SECTION 2 - HAZARDOUS INGREDIENTS / IDENTITY INFORMATION HAZARDOUS COMPONENTS CAS # % (wt.) OSHA PEL/STEL ACGIH TLV/TWA/STEL (SPECIFIC CHEMICAL IDENTITY; COMMON NAME(S)) (OPTIONAL) PPM MG/M3 PPM MG/M3 Ethyl Alcohol 64-17-5 1000 (PEL) 1000 (TLV) Lidocaine HCl 6108-05-0 2 None Established None Established Menthol 2216-51-5 None Established None Established This product is not known to contain a substance subject to Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA) and 40 CFR 372 at or above minimal amounts. SECTION 3 - HEALTH HAZARD DATA ROUTES OF ENTRY - SIGNS AND SYMPTOMS OF EXPOSURE EMERGENCY AND FIRST AID PROCEDURES EYES: Brief contact may cause mild irritation; prolonged contact may cause moderate irritation associated with redness.


INHALATION: Brief (minutes) inhalation will not cause adverse effects; prolonged and constant inhalation may cause irritation to the upper respiratory tract.

If irritation occurs, remove to fresh air and provide oxygen if breathing is difficult; seek medical attention if required

SKIN: Prolonged or repeated skin contact may cause mild irritation.

If irritation occurs, flush with clear running water for a minimum of 15 minutes; if irritation persists, seek medical attention.


DO NOT induce vomiting; seek immediate medical attention.

HEALTH HAZARDS (ACUTE AND CHRONIC): Acute effects are possible irritation and discomfort; chronic effects are possible with the ingestion of large amounts to the nervous system. Do not use on abraded skin. CARCINOGENICITY NTP? No IARC MONOGRAPHS? No OSHA REGULATED? No

No additional information MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: Preexisting skin, eye or respiratory disorders may become aggravated through prolonged exposure.

SAFETEC OF AMERICA

MATERIAL SAFETY DATA SHEET IDENTITY (AS USED ON LABEL AND LIST) Page 2 of 2 Safetec Sting Relief TM - Towelette Date: February 27, 2006

MSDS PREPARED BY: Safetec of America, Inc., 887 Kensington Avenue @ William L. Gaiter Pkwy., Buffalo, NY 14215 (716) 895-1822 Form Revised 1/99

SECTION 4 - FIRE FIGHTING MEASURES FLASH POINT (TOC) FLAMMABLE LIMITS (% Volume in Air for Lowest Flashing Component) 15.7°C LEL: 3.3 UEL: 19 EXTINGUISHING MEDIA dry chemicals, alcohol-type or all-purpose foam, CO2 SPECIAL FIRE FIGHTING PROCEDURES DO NOT enter confine fire space without full bunker gear (Helmet with face shield, bunker coats, gloves and rubber boots. Wear

NIOSH/MSHA approved self contained breathing apparatus. Cool fire exposed containers with water. A water spray may be used to dispense vapors; re-ignition is possible.

UNUSUAL FIRE AND EXPLOSIVE HAZARDS Flammable liquid. Concentrated vapors may be flammable.

SECTION 5 - PRECAUTIONS FOR SAFE HANDLING AND USE / LEAK PROCEDURES STEPS TO BE TAKEN IF MATERIAL IS SPILLED OR RELEASED Small spills may be flushed with large amounts of water; larger spills should be collected with approved absorbent for disposal. WASTE DISPOSAL METHODS Dispose of in accordance with Local, State, and Federal regulations. Products classified as non-hazardous may become hazardous


PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE Keep container(s) tightly closed when not in use. Store in cool, dry area away from possible sources of ignition. Keep this and other

chemicals out of reach of children. SECTION 6 - EXPOSURE CONTROLS / PERSONAL PROTECTION RESPIRATORY PROTECTION VENTILATION LOCAL EXHAUST: Required Ordinarily, none required MECHANICAL (GENERAL): No PROTECTIVE GLOVES EYE PROTECTION Ordinarily, none required Ordinarily, none required OTHER PROTECTIVE CLOTHING OR EQUIPMENT WORK / HYGIENIC PRACTICES Ordinarily, none required Practice safe work habits. Use according to label instructions.

SECTION 7 - PHYSICAL / CHEMICAL PROPERTIES BOILING POINT SPECIFIC GRAVITY (WATER=1) 173°F (Based on Ethyl Alcohol) 0.92 VAPOR PRESSURE (mm Hg) MELTING POINT Not Determined Not applicable VAPOR DENSITY (AIR=1) pH Not Determined Approximately 4.3 SOLUBILITY IN WATER EVAPORATION RATE (n-BUTYL ACETATE=1) Complete to moderate Not Determined APPEARANCE AND ODOR % VOLATILES (BY WEIGHT) Clear liquid. Not Determined

SECTION 8 - STABILITY AND REACTIVITY STABILITY UNSTABLE: CONDITIONS TO AVOID STABLE: XXX Extreme temperatures; sources of ignition INCOMPATIBILITIES (MATERIALS TO AVOID) Strong oxidizing/reducing agents HAZARDOUS DECOMPOSITION OR BYPRODUCTS Decomposition will not occur if handled / stored properly. Thermal decomposition may produce carbon monoxide, small amounts of

nitrogen oxides, halogenated compounds or propionaldehyde may also be formed. HAZARDOUS POLYMERIZATION MAY OCCUR:

WILL NOT OCCUR: XXX The information contained herein is believed to be accurate but is not warranted to be so. Users are advised to confirm in advance of need that information is current, applicable and suited to the circumstances of use. Vendor assumes no responsibility for injury to vendee or third persons proximately caused by the material if reasonable safety procedures are not adhered to as stipulated in the data sheet. Furthermore, vendor assumes no responsibility for injury caused by abnormal use of this material even if reasonable safety procedures are followed.


#P-H21082 #P-Q08472 #P-Q24272 #P-U22495

SANI-CLOTH HB

Section I -- Product Identification

Product/Trade Name: Sani Cloth HB Solution

Manufacturer's Name: PDI Professional Disposables, Inc.

The HealthCare Division of Nice-Pak Products, Inc.

Manufacturer's Address: 2 Nice-Pak Park Orangeburg, NY10962-1376

Hazard Rating (NFPA): Health: 0

Flammability: 0

Reactivity: 0

Specific: None

Emergency or Information Phone No.: 914-365-1700 (M-F Daytime)

At other times contact the local Poison Control Center

Chemical Name: Proprietary Mixture

Section II -- Hazardous Ingredients Per 29 CFR 1910.1200

HAZARDOUS INGREDIENTS CAS NUMBER % ACGIH-TLV

Quaternary Ammonium CMPD 68391-01-5/68956-79-6 10 N/A

Section III -- Physical/Chemical Characteristics

Color/Appearance: Clear colorless liquid

Odor: Mild quat odor

Boiling Point: N/A

Flash Point: Not applicable

Vapor Density: N/A

Evaporation Rate: N/A

Solubility in Water: Complete

Specific Gravity (H20=1): 1.0

Section IV -- Fire and Explosion Hazard Data

Flash Point (Method Used): Not applicable LEL: N/A UEL: N/A

Extinguishing Media: None

Special Firefighting Procedures: None

Unusual Fire and Explosion Hazards: None

Section V -- Reactivity Data

Stability: Stable

Conditions to avoid: None known

Incompatibility: Anionic surfactants, soaps

Hazardous Decomposition of Byproduct: None known

Polymerization: Will not occur

Section VI -- Health Hazard Data

Effects of Overexposure:



Skin: May cause skin irritation

Eyes: May cause irritation

Inhalation: Not a normal route of entry

Ingestion: Not a normal route of entry

Emergency and First Aid Procedures:

Skin Contact: If rash or irritation develops, discontinue use.

Eye Contact: Flush with cool water for 15 minutes.

Inhalation: Remove to fresh air

Ingestion: Consult physician.

Target Organs: N/A

Carcinogen: None known

Section VII -- Spill and Disposal Procedure

Spill Control: Pick up with absorbent

Waste Disposal Method: Follow local, state and federal regulations.

Handling and Storage: Store at room temperature in closed drums.

Section VIII -- Control Measures/Protection

Respiration: Use NIOSH approved respirator if exposure level is exceeded.

Ventilation: Recommended

Protective Gloves: Recommended

Eye Protection: If splashing may occur

Hygienic Practices: Follow good housekeeping practices.

Other: None

Section IX -- Transport/Shipping

DOT Shipping Name:

Technical Shipping Name:

DOT Shipping Classification: DOT not regulated

DOT ID Number:

DOT Label Requirements: N/A

UN/NA Number Regulations: N/A

Reportable Quantity: N/A

Disclaimer:

The information furnished herein is believed to be accurate and represents the best data currently available to us. No warranty, expressed

or implied, is made and Nice-Pak Products, Inc. assumes no legal responsibility or liability resulting from its use.

Executive Headquarters: 10 Glenshaw Street, Orangeburg, NY 10962

Phone: (845) 365-8200 • Toll Free: (888) 335-7500 • (888) DYNAREX

Fax: (845) 365-8201 • Email: [email protected] • www.dynarex.com



Iwdistte The Brands That Worl€,

900 Livety Btvd.Wood Dale, lL 60191630-694-4100 Locat

*, ??! 83iJg:f I:i!T::www. mediqueproducts.com

R.' lv'rcri'sdcryDaa shcets for All Tcxdrersc Mediq.c Tabra prod'cts

Dear Customer;

vitl reqpcct to to.t rcqucsc for ldeterial safery Daa :Fac) 04sD$ on onr Tcxtilese li,Iediq,rc tabletproduc$' plcass bc dvised 6at-all of o'rproducrs are crcmprcdfu-G r.qrrio-.o. as citcd below;

-^---o-1T1.* llnptcd :5f T e retail csteblishmcnt which *c prck ged for sale to colsu.Dcrr- (29 cF:R1900'u00 (b) (e) (")' Accordingb .ll o"o*h"orrar"r-d*gs ve"c *9-p'"d &"- tbc poic of prrc-gi,!& r,ce rf,cr3re pa&ged prior to rcachiag a rceil c$ablishEcst 6: rgoasc2gi3&31 6.gus, g, 198g)). ollsA b:s funlcraeto{'siaccthcsepro&*.arecxenpd"-pr"y";-uJp"a.[*rJi*oousaicvourdnotharrtofi'nish

lfi?r1 t distrrbuon accivins thc prlduct' rs) *o-nsEirm,,ffi; .u,84i s3rroasc:si34 (Augns 8,

Thcrcfore over\uar1 dnrgs prcpdq'd for re..il salc are cxclcpr &oq thc osI{A rre,.ld

ffi*Tio"rmrff;ffi1"H*t rhe requireocat r* . usos) &oo thc .,-.-"r Fcedas

Siuccrdn

ersAGeorgSperbcrDircccor of Rcguletory Afiain/ etuliry Ass.nacc.



HMIS HAZARD RATING

HEALTH 1 0 = INSIGNIFICANT 3 = HIGH FLAMMABILITY 1 1 = SLIGHT 4 = EXTREME REACTIVITY 0 2 = MODERATE TRANSPORTATION INFORMATION PROPER SHIPPING NAME Safetec Triple Antibiotic Ointment HAZARD CLASS / PKG. GRP. Not applicable REF. Not applicable IDENTIFICATION NUMBER Not applicable LABEL None Required Ground

SECTION 1 - PRODUCT / COMPANY IDENTIFICATION IDENTITY (AS USED ON LABEL AND LIST) Page 1 of 2 Safetec Triple Antibiotic Ointment MANUFACTURER’S NAME EMERGENCY TELEPHONE NUMBER (24 Hours) Safetec of America, Inc. (800) 255-3924 ADDRESS (NUMBER, STREET, P.O. BOX) TELEPHONE NUMBER FOR INFORMATION 887 Kensington Avenue @ William L. Gaiter Pkwy. (716) 895-1822 (CITY, STATE AND ZIP CODE) DATE PREPARED September 1, 2004 Buffalo, NY 14215 SUPERSEDES August 14, 2002

SECTION 2 - HAZARDOUS INGREDIENTS / IDENTITY INFORMATION HAZARDOUS COMPONENTS CAS # % (wt.) ACGIH TLV/TWA/STEL (SPECIFIC CHEMICAL IDENTITY; COMMON NAME(S)) (OPTIONAL) PPM MG/M3

This product is not known to contain a substance subject to Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA) and 40 CFR 372 at or above minimal amounts. SECTION 3 - HEALTH HAZARD DATA ROUTES OF ENTRY - SIGNS AND SYMPTOMS OF EXPOSURE EMERGENCY AND FIRST AID PROCEDURES INHALATION: Not likely due to the physical state of the product.

Remove to fresh air. Give artificial respiration if necessary.

EYES: Use only specified ophthalmic ointment in eyes. Topical ointment will cause eye irritation.

Flush eyes with copious amounts of water for at least 15 minutes.

INGESTION: May cause kidney, liver, and gastro-intestinal impairment; may induce dizziness, incoordination, sensory loss and deafness.

Induce vomiting. Do not give anything to an unconscious person.

SKIN: Non-toxic under standard application.

Wash with soap and water.

HEALTH HAZARDS (ACUTE AND CHRONIC): Acute: Allergy, kidney and liver impairment, dizziness, incoordination, sensory loss, deafness, nausea, vomiting and diarrhea. Chronic: Repeated or prolonged exposure may cause allergic reactions in susceptible individuals. CARCINOGENICITY NTP? No IARC MONOGRAPHS? No OSHA REGULATED? No No additional information MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: Susceptible individuals may have an allergice reaction

SAFETEC OF AMERICA

Form Revised 6/01/2000

MATERIAL SAFETY DATA SHEET IDENTITY (AS USED ON LABEL AND LIST) Page 2 of 2 Safetec Triple Antibiotic Ointment Date: September , 2004 SECTION 4 - FIRE FIGHTING MEASURES FLASH POINT (METHOD USED) FLAMMABLE LIMITS (% Volume in Air for Lowest Flashing Component) Not available LEL: Not available UEL: Not available EXTINGUISHING MEDIA Use extinguishing media appropriate for the surrounding fire. Use alcohol foam, dry chemical or CO2. SPECIAL FIRE FIGHTING PROCEDURES Wear full protective clothing. UNUSUAL FIRE AND EXPLOSIVE HAZARDS May emit toxic fumes.

SECTION 5 - PRECAUTIONS FOR SAFE HANDLING AND USE / LEAK PROCEDURES STEPS TO BE TAKEN IF MATERIAL IS SPILLED OR RELEASED Assure slippery conditions are nullified. Add sand or dirt. Scoop up and remove. Wash area with soap and water. Dispose in

accordance with federal, state, and local regulations. WASTE DISPOSAL METHODS Dispose of in accordance with Local, State, and Federal regulations. Products classified as non-hazardous may become hazardous


PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE Keep containers closed when not in use. Do not handle or store near heat, flames or oxidizers.

SECTION 6 - EXPOSURE CONTROLS / PERSONAL PROTECTION RESPIRATORY PROTECTION VENTILATION LOCAL EXHAUST: Recommended Not required MECHANICAL (GENERAL): Not required PROTECTIVE GLOVES EYE PROTECTION Not required for normal use Not required for normal use OTHER PROTECTIVE CLOTHING OR EQUIPMENT WORK / HYGIENIC PRACTICES Eye wash stations should be nearby and ready for use. Practice safe work habits. Use according to label instructions.

SECTION 7 - PHYSICAL / CHEMICAL PROPERTIES BOILING POINT SPECIFIC GRAVITY (WATER=1) 343°C (650 °F) VAPOR PRESSURE (mm Hg) MELTING POINT No data 54°C (130 °F) VAPOR DENSITY (AIR=1) PH (1% solution in water) No data No data SOLUBILITY IN WATER EVAPORATION RATE (IPA=1) Insoluble No data APPEARANCE AND ODOR % VOLATILES (BY VOLUME) White to off- white ointment No data

SECTION 8 - STABILITY AND REACTIVITY STABILITY UNSTABLE: CONDITIONS TO AVOID STABLE: XXX Heat and oxidizing INCOMPATIBILITIES (MATERIALS TO AVOID) Extreme heat, sparks, open flame, oxidizers, strong acids and alkalies. HAZARDOUS DECOMPOSITION OR BYPRODUCTS May give off fumes of carbon monoxide and carbon dioxide. HAZARDOUS POLYMERIZATION MAY OCCUR: CONDITIONS TO AVOID

WILL NOT OCCUR: XXX Temperatures above 300°C, The information contained herein is believed to be accurate but is not warranted to be so. Users are advised to confirm in advance of need that information is current, applicable and suited to the circumstances of use. Vendor assumes no responsibility for injury to vendee or third persons proximately caused by the material if reasonable safety procedures are not adhered to as stipulated in the data sheet. Furthermore, vendor assumes no responsibility for injury caused by abnormal use of this material even if reasonable safety procedures are followed.

MSDS PREPARED BY: Safetec of America, Inc., 887 Kensington Avenue @ William L. Gaiter Pkwy. , Buffalo, NY 14215 (716) 895-1822 Form Revised 6/01/2000