4-port antenna r1 y1 frequency range 698–960 dual … · 80010666v01 page 1 of 4 4-port antenna...

80010666V01 of 4

4-Port AntennaFrequency RangeDual PolarizationHPBWAdjust. Electr. DTset by hand or by optional RCU (Remote Control Unit)

1710–2690

Y1Y1

698–960

R1R1

XX

65°65°

2°–8°1.5°–10°

936.

4652

/e

ngm

n 04

.18.

08.0

7 S

ubje

ct to

alte

ratio

n.

4-Port Antenna 698–960/1710–2690 65°/65° 17/18.5dBi 1.5°–10°/2°–8°T

Type No. 80010666V01Lowband R1, connector 1–2R1, connector 1–2

698–960Frequency Range MHz 698 – 806 790 – 862 824 – 894 880 – 960

Gain at mid Tilt dBi 16.0 16.6 16.9 17.1

Gain over all Tilts dBi 16.0 ± 0.5 16.5 ± 0.4 16.8 ± 0.4 17.0 ± 0.2

Horizontal Pattern:Azimuth Beamwidth ° 71 ± 2.2 68 ± 1.0 68 ± 0.9 67 ± 1.5

Front-to-Back Ratio,Total Power, ± 30°

dB > 22 > 24 > 26 > 27

Cross Polar Discriminationat Boresight

dB > 23 > 22 > 22 > 21

Cross Polar Discriminationover Sector

dB > 8.0 > 8.5 > 9.5 > 8.5

Vertical Pattern:Elevation Beamwidth ° 8.4 ± 0.7 7.7 ± 0.4 7.5 ± 0.4 7.0 ± 0.3

Electrical Downtiltcontinuously adjustable

° 1.5 – 10.0

Tilt Accuracy ° < 0.3 < 0.3 < 0.3 < 0.3

First Upper Side Lobe Suppression

dB > 16 > 17 > 16 > 15

Upper Side Lobe Suppression, 20° Sector above Main Beam

dB > 16 > 17 > 16 > 15

Cross Polar Isolation dB > 30

Port to Port Isolation dB > 30 (R1 // Y1)

Max. Effective Powerper Port

W 400 (at 50 °C ambient temperature)

Max. Effective PowerPort 1–2


Values based on NGMN-P-BASTA (version 9.6) requirements.

Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]

All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com

of 4 80010666V01

936.

4652

/e

ngm

n 04

.18.

08.0

7 S

ubje

ct to

alte

ratio

n.

4-Port Antenna

Highband Y1, connector 3–4Y1, connector 3–4

1710–2690Frequency Range MHz 1710 – 1880 1850 – 1990 1920 – 2170 2300 – 2400 2490 – 2690

Gain at mid Tilt dBi 18.0 18.5 18.8 18.6 19.0

Gain over all Tilts dBi 18.0 ± 0.4 18.5 ± 0.4 18.7 ± 0.4 18.5 ± 0.7 18.8 ± 0.4

Horizontal Pattern:Azimuth Beamwidth ° 64 ± 3.4 62 ± 2.9 62 ± 2.2 60 ± 4.8 60 ± 2.0

Front-to-Back Ratio,Total Power, ± 30°

dB > 25 > 26 > 27 > 25 > 26

Cross Polar Discriminationat Boresight

dB > 15 > 18 > 20 > 16 > 21

Cross Polar Discriminationover Sector

dB > 8.0 > 11.0 > 11.0 > 10.0 > 9.5

Vertical Pattern:Elevation Beamwidth ° 5.0 ± 0.4 4.7 ± 0.2 4.4 ± 0.4 3.9 ± 0.2 3.5 ± 0.2

Electrical Downtiltcontinuously adjustable

° 2.0 – 8.0

Tilt Accuracy ° < 0.2 < 0.2 < 0.2 < 0.2 < 0.2

First Upper Side Lobe Suppression

dB > 19 > 18 > 20 > 20 > 18

Upper Side Lobe Suppression, 20° Sector above Main Beam

dB > 16 > 16 > 16 > 16 > 17

Cross Polar Isolation dB > 28

Port to Port Isolation dB > 30 (R1 // Y1)

Max. Effective Powerper Port


Max. Effective PowerPort 3–4


Values based on NGMN-P-BASTA (version 9.6) requirements.



80010666V01 of 4

936.

4652

/e

ngm

n 04

.18.

08.0

7 S

ubje

ct to

alte

ratio

n.4-Port Antenna

Adjustment mechanismwith integrated scale

All dimensionsin mm | inches

2622

| 10

3.2

2652

| 10

4.4

2692

| 10

6.0

2)1)

1) 9 | 0.42) 72 | 2.8

For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.Wall mounting: No additional mounting kit needed.

Material: Refl ector screen: Aluminum.Fiberglass housing: It covers totally the internal antenna components. The special design reduces the sealing areas to a minimum and guarantees the best weather protection. Fiberglass material guarantees optimum performance with regards to stability, stiffness, UV resistance and painting. The color of the radome is light grey.All nuts and bolts: Stainless steel or hot-dip galvanized steel.

Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded.

Electrical specifi cations, all systems

Impedance Ω 50VSWR < 1.5Return Loss dB > 14Interband Isolation dB > 30Passive Intermodulation dBc < –150 (2 x 43 dBm carrier)Polarization ° +45, –45Max. Effective Powerfor the Antenna W 900 (at 50 °C ambient

temperature)Values based on NGMN-P-BASTA (version 9.6) requirements.

Mechanical specifi cations

Input 4 x 7-16 female long neckConnector Position bottomAdjustment Mechanism 2x, Position bottom

continuously adjustableWind load (at Rated Wind Speed: 150 km/h)

N | lbf Frontal: 530 | 119Maximal: 845 | 190

Max. Wind Velocity km/hmph

200124

Height / Width / Depth mminches

2622 / 300 / 152103.2 / 11.8 / 6.0

Category of Mounting Hardware H (Heavy)

Weight kglb

29.0 / 31.2 (clamps incl.)63.9 / 68.8 (clamps incl.)

Packing Size mminches

2951 / 322 / 190116.2 / 12.7 / 7.5

Scope of Supply Panel and 2 units of clamps for 42–115 mm |

1.7–4.5 inches diameter

Accessories (order separately if required)

Type No. Description Remarksmm | inches

Weight approx.kg | lb

Units per antenna

85010002 1 clamp Mast diameter: 110 – 220 | 4.3 – 8.7 2.7 | 6.0 285010003 1 clamp Mast diameter: 210 – 380 | 8.3 – 15.0 4.8 | 10.6 285010008 1 downtilt kit Downtilt angle: 0° – 8° 4.3 | 9.5 1

Accessories (included in the scope of supply)738546 1 clamp Mast diameter: 42 – 115 | 1.7 – 4.5 1.1 | 2.4 2



of 4 80010666V01

4-Port Antenna

173

| 6.8

*

46 |

1.8

49 |

1.9

108

| 4.3

101 | 4.0

221 | 8.7

244 | 9.6

152

| 6.0

*

300 | 11.8 *

Tilt 1710-2690Tilt 6

98-960

Bottom view* Dimensions refer to radomeAll dimensions in mm | inches

Layout of interface:

Correlation Table

Frequency range Array Connector

698– 960 MHz R1 1–2

1710–2690 MHz Y1 3–4

R1Y1

936.

4652

/e

ngm

n 04

.18.

08.0

7 S

ubje

ct to

alte

ratio

n.



738546 Page 1 of 1

Mounting HardwareClamp Included in the Scope of Supply

936.

3920

/c

Sub

ject

to a

ltera

tion.

Suitable for mast diameter (mm)[inches]

42 – 115[1.65 – 4.53]

Antenna – mast distance (mm)[inches]

20 – 25[0.79 – 0.98]

Material of clamp and screws Hot-dip galvanized steel / stainless steel

Weight (kg)[lb]

1.1[2.43]

Please note: Kathrein does not recommend to use counter nuts.The additional nuts supplied are only meant as spares.

All dimensions in mm and [inches]

152 [5.98]

100 [3.94]40 [1.57]

72 [2.83]

35 [1.38]

64 [2.52]

125 [4.92]

40 [1

.57]

20–

25

[0.7

9–

0.98

]

42–115

[1.65–4.53]

M10 MA = 25 Nm

M8 MA = 20 Nm

20–25

[0.79–0.98]



of 2

936.

4037

/a

Sub

ject

to

alte

ratio

n.General Instructionsfor Adjustment Mechanism

Description of the adjustment mechanism (protective cap removed):

Manual adjustment procedure:

Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment:

For a description of RCU installation please refer to the respective data sheet.

Remove the protective cap and the twist protection completely.

➀ Twist protection.➁ Downtilt spindle with integrated

scale.

➀ Thread for fi xing the pro tectivecap or the RCU (Remote ControlUnit).

➁ Gearwheel for RCU power drive.

To set the downtilt angle exactly, you must look horizontally at the scale. The lower edge of the gear-wheel must be used for alignment.

Set downtilt angle by rotating the gearwheel.

Screw on the twist protection and the protective cap again.

0° – max.°

0° – max.°

1

2

2

1



of 2

936.

4037

/a

Sub

ject

to

alte

ratio

n.

Installation of the feederline connector and RCU (optional):In order to protect the adjustment mechanism, the protective caps have to be attached during feederline installation!

Carefully place the connector and fi x the nut using a torque-wrench (according to the manufacturers guidelines).

After feederline installation, the optional remote control units (RCUs) can be mounted.

These tools are suitable for 7-16 connectors with a wrench size of 27 or 32 mm | 1.1 or 1.3 inches, and the RCU attachment nut with a wrench size of 41 mm | 1.6 inches.

Tighten nuts within a torque range of 25 – 33 Nm depending on connector manufacturers’ specifi cations, respectively the RCU nut with a torque range of 15 – 18 Nm.

Kathrein installation set: Type No. 85010077Set has to be ordered separately!Set consists of three spanners of divers width27, 32 and 41 mm | 1.1, 1.3 and 1.6 inches

32 | 1.3

41 | 1

.627 | 1.1

1/2˝ square actuationaccording toDIN 3120 Form C

All dimensions in mm | inches

Colour coding:Correlation of each RF input to:– the corresponding adjustment mechanism– the frequency range– the polarization

Ventilation hole

Spindle with tilting scale

7-16 female (long neck)

Adjustment mechanism(protective cap removed)

General Instructions for Feederline and RCU Installation for Antennas

Please note: In order not to damage the interfaces, please make sure that only the right tools are used. Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrench width.

Description of bottom end cap (exemplary picture):



4-port antenna r1 y1 frequency range 698–960 dual … · 80010666v01 page 1 of 4 4-port antenna...

Documents