8-port antenna frequency range dual polarization hpbw … · 80010826 page 1 of 4 8-port antenna...

80010826 of 4

8-Port AntennaFrequency RangeDual PolarizationHPBWAdjust. Electr. DTset by hand or by optional RCU (Remote Control Unit)

1710–2180 1710–2180790–960 790–960

X XX X

60° 60°65° 65°

0°–6° 0°–6°0°–8° 0°–8°

R2R2 B1B1 B2B2R1R193

6.48

87/b

ng

mn

04.1

9.02

.00

Sub

ject

to

alte

ratio

n.

8-Port Antenna 790–960/790–960/1710–2180/1710–2180 65°/65°/60°/60° 17/17/18.5/18.5dBi0°–8°/0°–8°/0°–6°/0°–6°T

Type No. 80010826Lowbands R1R1 R2R2

790–960 790–960Frequency Range MHz 790 – 862 824 – 894 880 – 960 790 – 862 824 – 894 880 – 960Gain at mid Tilt dBi 16.6 16.8 16.7 16.5 16.8 16.8Gain over all Tilts dBi 16.5 ± 0.3 16.6 ± 0.2 16.6 ± 0.3 16.5 ± 0.4 16.6 ± 0.2 16.6 ± 0.3Horizontal Pattern:Azimuth Beamwidth ° 65 ± 2.3 64 ± 2.0 62 ± 2.4 66 ± 2.8 64 ± 2.2 63 ± 2.5Front-to-Back Ratio,Total Power, ± 30°

dB > 26 > 27 > 28 > 25 > 26 > 27

Cross Polar Discriminationat Boresight

dB > 31 > 32 > 29 > 30 > 30 > 29

Cross Polar Discrimination over Sector

dB > 15.0 > 13.5 > 12.0 > 15.0 > 14.0 > 11.5

Azimuth Beam Port-to-Port Tracking

dB < 1.5 < 1.5 < 1.5 < 1.5 < 1.5 < 1.5

Vertical Pattern:Elevation Beamwidth ° 8.1 ± 0.3 7.9 ± 0.3 7.5 ± 0.3 8.0 ± 0.3 7.8 ± 0.3 7.5 ± 0.3Electrical Downtiltcontinuously adjustable

° 0.0 – 8.0 0.0 – 8.0

Tilt Accuracy ° < 0.2 < 0.2 < 0.3 < 0.2 < 0.2 < 0.3First Upper Side Lobe Suppression

dB > 16 > 17 > 16 > 16 > 17 > 16

Cross Polar Isolation dB > 30 > 30Port to Port Isolation dB > 30 (R1 // R2 // B1 // B2) > 30 (R1 // R2 // B1 // B2)Max. Effective Powerper Port

W 400 (at 50 °C ambient temperature) 400 (at 50 °C ambient temperature)

Values based on NGMN-P-BASTA (version 9.6) requirements.

Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]

All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com

of 4 80010826

936.

4887

/b

ngm

n 04

.19.

02.0

0 S

ubje

ct t

o al

tera

tion.

8-Port Antenna

Highbands B1B1 B2B2

1710–2180 1710–2180Frequency Range MHz 1710 – 1880 1850 – 1990 1920 – 2180 1710 – 1880 1850 – 1990 1920 – 2180Gain at mid Tilt dBi 18.4 18.5 18.4 18.4 18.6 18.6Gain over all Tilts dBi 18.3 ± 0.3 18.4 ± 0.4 18.2 ± 0.5 18.3 ± 0.4 18.5 ± 0.5 18.4 ± 0.5Horizontal Pattern:Azimuth Beamwidth ° 60 ± 2.4 57 ± 2.5 59 ± 3.4 60 ± 2.9 57 ± 2.1 58 ± 3.2Front-to-Back Ratio,Total Power, ± 30°

dB > 26 > 25 > 24 > 25 > 26 > 26

Cross Polar Discriminationat Boresight

dB > 28 > 28 > 24 > 28 > 27 > 24

Cross Polar Discrimination over Sector

dB > 16.0 > 15.5 > 10.0 > 15.0 > 14.5 > 9.5

Azimuth Beam Port-to-Port Tracking

dB < 0.5 < 1.0 < 1.5 < 0.5 < 1.0 < 1.5

Vertical Pattern:Elevation Beamwidth ° 5.0 ± 0.3 4.7 ± 0.2 4.5 ± 0.4 5.0 ± 0.3 4.7 ± 0.2 4.5 ± 0.4Electrical Downtiltcontinuously adjustable

° 0.0 – 6.0 0.0 – 6.0

Tilt Accuracy ° < 0.2 < 0.2 < 0.2 < 0.3 < 0.2 < 0.2First Upper Side Lobe Suppression

dB > 14 > 14 > 14 > 14 > 15 > 15

Cross Polar Isolation dB > 30 > 30Port to Port Isolation dB > 30 (R1 // R2 // B1 // B2) > 30 (R1 // R2 // B1 // B2)Max. Effective Powerper Port

W 250 (at 50 °C ambient temperature) 250 (at 50 °C ambient temperature)

Values based on NGMN-P-BASTA (version 9.6) requirements.



Any previous data sheet issues have now become invalid.

8-Port Antenna

80010826 of 4

936.

4887

/b

ngm

n 04

.19.

02.0

0 S

ubje

ct t

o al

tera

tion.

For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.Wall mounting with two half clamps 738546 (included in the scope of supply).

Material: Refl ector screen: Weather-proof aluminum.Fiberglass radome: The grey fi berglass radomes of these antennas are very stable and extraordinarily stiff. They are resistant to ultraviolet radiation and can also be painted to match their surroundings.All screws and nuts: Stainless steel

Grounding: The metal parts of the antenna including the mounting and the inner conductors are DC grounded.

Accessories (order separately if required)

Type No. Description Remarksmm | inches

Weight approx.kg | lb

Units per antenna

85010002 1 clamp Mast diameter: 110 – 220 | 4.3 – 8.7 2.7 | 6.0 285010003 1 clamp Mast diameter: 210 – 380 | 8.3 – 15.0 4.8 | 10.6 285010008 1 downtilt kit Downtilt angle: 0° – 9° 4.3 | 9.5 1

Accessories (included in the scope of supply)738546 1 clamp Mast diameter: 42 – 115 | 1.7 – 4.5 1.1 | 2.4 2

2)

2399

| 94

.424

32 |

95.7

2472

| 97

.3

Adjustment mechanismwith integrated scale

All dimensions in mm | inches

1)1) 9 | 0.42) 72 | 2.8

Electrical specifi cations, all systems

Impedance Ω 50VSWR < 1.5Return Loss dB > 14Interband Isolation dB > 30Passive Intermodulation dBc < –150 (2 x 43 dBm carrier)Polarization ° –45, +45Max. Effective Powerfor the Antenna W 1200 (at 50 °C ambient

temperature)Values based on NGMN-P-BASTA (version 9.6) requirements.

Mechanical specifi cations

Input 8 x 7-16 femaleConnector Position bottomAdjustment Mechanism 4x, Position bottom

continuously adjustableWind load (at Rated Wind Speed: 150 km/h)

N | lbf Frontal: 1550 | 348Maximal: 1705 | 383

Max. Wind Velocity km/hmph

200124

Height / Width / Depth mminches

2399 / 576 / 13394.4 / 22.7 / 5.2

Category of Mounting Hardware H (Heavy)

Weight kglb

39.0 / 41.2 (clamps incl.)86.0 / 90.8 (clamps incl.)

Packing Size mminches

2576 / 600 / 170101.4 / 23.6 / 6.7

Scope of Supply Panel and 2 units of clampsfor 42–115 mm |

1.7–4.5 inches diameter



Any previous data sheet issues have now become invalid.

of 4 80010826

936.

4887

/b

ngm

n 04

.19.

02.0

0 S

ubje

ct t

o al

tera

tion.

8-Port Antenna

Layout of interface:

Correlation Table

Frequency range Array Connector

790– 960 MHz R1 1–2 790– 960 MHz R2 3–41710–2180 MHz B1 5–61710–2180 MHz B2 7–8

R1B1

R2B2

Left Right

1) 2)

270 | 10.6 3)

476 | 18.7

576 | 22.7 *

Bottom view* Dimensions refer to radomeAll dimensions in mm | inches

99 |

3.9

110

| 4.3

133

| 5.2

*

34 |

1.3

4)

Tilt 790-960

17

10-2180 Tilt

Tilt 790-960 1710-2180

Tilt

56 |

2.2

1) 33.5 | 1.32) 35.5 | 1.43) 50 | 2.04) 45 | 1.8



738546 Page 1 of 1

Mounting HardwareClamp Included in the Scope of Supply

936.

3920

/c

Sub

ject

to a

ltera

tion.

Suitable for mast diameter (mm)[inches]

42 – 115[1.65 – 4.53]

Antenna – mast distance (mm)[inches]

20 – 25[0.79 – 0.98]

Material of clamp and screws Hot-dip galvanized steel / stainless steel

Weight (kg)[lb]

1.1[2.43]

Please note: Kathrein does not recommend to use counter nuts.The additional nuts supplied are only meant as spares.

All dimensions in mm and [inches]

152 [5.98]

100 [3.94]40 [1.57]

72 [2.83]

35 [1.38]

64 [2.52]

125 [4.92]

40 [1

.57]

20–

25

[0.7

9–

0.98

]

42–115

[1.65–4.53]

M10 MA = 25 Nm

M8 MA = 20 Nm

20–25

[0.79–0.98]



of 2

936.

4037

/a

Sub

ject

to

alte

ratio

n.General Instructionsfor Adjustment Mechanism

Description of the adjustment mechanism (protective cap removed):

Manual adjustment procedure:

Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment:

For a description of RCU installation please refer to the respective data sheet.

Remove the protective cap and the twist protection completely.

➀ Twist protection.➁ Downtilt spindle with integrated

scale.

➀ Thread for fi xing the pro tectivecap or the RCU (Remote ControlUnit).

➁ Gearwheel for RCU power drive.

To set the downtilt angle exactly, you must look horizontally at the scale. The lower edge of the gear-wheel must be used for alignment.

Set downtilt angle by rotating the gearwheel.

Screw on the twist protection and the protective cap again.

0° – max.°

0° – max.°

1

2

2

1


of 2

936.

4037

/a

Sub

ject

to

alte

ratio

n.

Installation of the feederline connector and RCU (optional):In order to protect the adjustment mechanism, the protective caps have to be attached during feederline installation!

Carefully place the connector and fi x the nut using a torque-wrench (according to the manufacturers guidelines).

After feederline installation, the optional remote control units (RCUs) can be mounted.

These tools are suitable for 7-16 connectors with a wrench size of 27 or 32 mm | 1.1 or 1.3 inches, and the RCU attachment nut with a wrench size of 41 mm | 1.6 inches.

Tighten nuts within a torque range of 25 – 33 Nm depending on connector manufacturers’ specifi cations, respectively the RCU nut with a torque range of 15 – 18 Nm.

Kathrein installation set: Type No. 85010077Set has to be ordered separately!Set consists of three spanners of divers width27, 32 and 41 mm | 1.1, 1.3 and 1.6 inches

32 | 1.3

41 | 1

.627 | 1.1

1/2˝ square actuationaccording toDIN 3120 Form C

All dimensions in mm | inches

Colour coding:Correlation of each RF input to:– the corresponding adjustment mechanism– the frequency range– the polarization

Ventilation hole

Spindle with tilting scale

7-16 female (long neck)

Adjustment mechanism(protective cap removed)

General Instructions for Feederline and RCU Installation for Antennas

Please note: In order not to damage the interfaces, please make sure that only the right tools are used. Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrench width.

Description of bottom end cap (exemplary picture):



8-port antenna frequency range dual polarization hpbw … · 80010826 page 1 of 4 8-port antenna...

Documents