4112-4127 color scan kit
TRANSCRIPT
-
8/18/2019 4112-4127 Color Scan Kit
1/3
XEROXKit Installation Instructions Global Knowledge and Language Services
Product(s): Xerox 4112/4127 Date: 8/17/2007 Page: 1 of 3
Title: COLOR SCANNER KIT OPTION Kit part # 498K16720
Instruction #: 604E40940 Tag/MOD #: IOT 13 Classification code: O
Purpose To enable color scanning on the 4112 / 4127, for ColorScan back capabilities.
Kit Contents
Check the components contained in the kit.
Description Quantity
LYRA3 PWB. 1
Memory DIMM (128mb) 1
Stand-off hardware 1
Installation Instructions 1
PrerequisitesSystem SW v1.0 or higher
Procedure
Read the entire procedure before you start theremoval activity.
WARNING
Af ter turning OFF the copier, turn OFF the ci rcui tbreaker and unp lug the power cord and applyLockout Tag Kit
WARNING
Use the ESD kit to hand le the PWBs.
__ 1. Remove the ESS Chassis/Green Controllerfrom the Printer per Step 2 (PL 2.5 and Item1.)
__ 2. Unplug all of the cables and connectionslocated on the side of the ESS Chassis onthe IOT (Figure 1)
a) Remove the (5) screws.
b) Pull the top handle to remove the ESSChassis and place on a flat worksurface.
NOTE: If this system has an OHCF attached, it willbe necessary to disconnect; un-dock and move thefeeder away from the IOT in order to pull the GreenController out.
Figure 1
__ 3. If there is a DFE Enablement kit installed (tag3) proceed to Step 4, otherwise continue withstep 6
__ 4. Remove the BP PWB (Figure 2)a) Remove the (4) screws
b) Carefully separate the BP PWB from theDFE Interface and ESS PWB’s bymoving it in the direction of the arrows
Figure 2
BP PWB
a)
b)
a)
-
8/18/2019 4112-4127 Color Scan Kit
2/3
XEROXKit part #: 498K16720 Instruction #: 604E40940 Date: 8/17/2007 Page: 2 of 3
__ 5. Remove the (2) screws from the DFEInterface bracket/PWB. (Figure 3)
Figure 3
__ 6. Remove (1) screw and lift bracket and PWBupward (Fig 4)
NOTE: Backplane PWB shown installed in photo,but was removed in prior steps
Figure 4
__ 7. Install the Memory DIMM (128M) suppliedwith this kit in slot (Figure 5 DFE PWB shownremoved)
__ a. Insert supplied DIMM __ b. Using finger, gently press downward
to secure the DIMM
Figure 5
__ 8. Perform steps 4 through 6 to reinstall theDFE interface and BP PWB’s if removed inprevious steps.
DFE Interface PWB
__ 9. Install the LYRA3 PWB provided (Figure 6)
Note: Ensure the LYRA3 PWB is mated properlyprior to securing it to the ESS PWB in the followingsteps.
__ a. Remove / save the (1) screw. (Figure6)
Remove (1) screw
Lift PWB upward
Figure 6
-
8/18/2019 4112-4127 Color Scan Kit
3/3
XEROXKit part #: 498K16720 Instruction #: 604E40940 Date: 8/17/2007 Page: 3 of 3
__ b. Install the standoff included with thekit in place of the screw. (Figure 7)
Figure 7
__ c. Mate the LYRA3 PWB to the ESSPWB
__ d. Secure the LYRA3 PWB to theGreen Controller (1 screw removedpreviously). (Figure 7)
Figure 7
__ 10. Reinstall the ESS Chassis in the card cage.Ensure chassis engages 3 tabs at the topwhen inserting.
Verifying operation
__ 1. Reattach cabling removed in Step 2
__ 2. Reinstall covers.
__ 3. Remove the Lockout Tag device.
__ 4. Connect the Power Cord.
__ 5. Power “ON” the system.
__ 6. Verify DADF / Scanner and System operation
__ 7. Perform dC945 CCD calibration and WhiteReference Adjustments.
__ 8. Familiarize yourself with the added settingsin the Machine for the new Color ScanOptions:
SELECT: ALL SERVICES ICON
SELECT: SCAN TO PC
Observe Color Scan selections.
__ 9. If the Analyst Trainer or Customer IT personor User with System Administrator Guide hasset up the Scan to Mailbox or Scan to FTPfunction, verify Color scanning is workingcorrectly. If these features have not been setup, proceed to Call CLOSE.
__ 10. Mark off IOT Tag # 13