45642137 actix analyzer cell site data june 2010
TRANSCRIPT
www.actix.com
June 2010
Cell Site Data Technical Note
www.actix.com
The content of this manual is provided for information only, is subject to change without notice, and should not be construed as a commitment by Actix. Actix assumes no responsibility or liability for any errors or inaccuracies that appear in this documentation.
Copyright © Actix 2010. All rights reserved. All trademarks are hereby acknowledged.
www.actix.com
2
Contents
1 INTRODUCTION .......................................................................................... 4
2 IMPORTING NETWORK DATA ........................................................................... 5
2.1 OBTAINING SITE DATA IN TABULAR FORMAT .............................................................. 5 2.2 GUIDELINES FOR FORMATTING TABULAR DATA ............................................................ 7 2.3 IMPORTING THE DATA ........................................................................................ 8 2.4 IMPORTING MULTIPLE TECHNOLOGIES .................................................................... 14
3 UPDATING CELL SITE DATA .......................................................................... 15
3.1 AUTOMATIC IMPORT OF CELL SITE DATA ................................................................. 15
4 LOADING CELL SITE DATA ........................................................................... 17
5 CELL SITE DISPLAY ................................................................................... 18
5.1 DISPLAYING SITE LABELS .................................................................................. 18 5.2 COLORING SECTORS ON THE MAP ......................................................................... 20 5.3 SEARCHING FOR CELLS ..................................................................................... 21 5.4 VIEWING CELL SITE INFORMATION ....................................................................... 23
APPENDIX: CDMA CELL SITE PARAMETERS ......................................................... 25
APPENDIX: GSM / GPRS / EDGE CELL SITE PARAMETERS ...................................... 27
APPENDIX: IDEN CELL SITE PARAMETERS ........................................................... 29
APPENDIX: LTE CELL SITE PARAMETERS ............................................................. 31
APPENDIX: UMTS / HSPA+ CELL SITE PARAMETERS ............................................. 32
Actix Analyzer Cell Site Data Technical Note June 2010 Introduction 4
www.actix.com
2
1 Introduction
This document describes how to import delimited network element data into Actix Analyzer, and how to configure the Automatic Import tool.
Analyzer‟s Network Explorer feature allows you to import network element data, creating a cell plan file called cellrefs.txt. Network Explorer also lets
you browse and edit this network information once it has been loaded into Analyzer. The Automatic Import feature provides an automated method of updating cell site information in Analyzer, as changes are made to your
network.
In this document, CDMA network data is used as an example, but the
appendices show important information relating to other network technologies.
Actix Analyzer Cell Site Data Technical Note June 2010 Importing Network Data 5
www.actix.com
2
2 Importing Network Data
Analyzer‟s network data import process requires two files:
A delimited text file that contains unformatted data arranged in
tabular form, with one row for each individual sector in a network.
A blank file, containing only Analyzer header information, to be
populated with formatted data.
2.1 Obtaining Site Data in Tabular Format
In order to import cell site data from your own network, you will need to obtain a delimited text file containing the data listed in the table below. To
maximize the benefit Analyzer can bring to network analysis, the parameters listed in bold in the table on the following page are required
for cell data to function with logged data in the main workspace. All other parameters are optional.
The data may come from a network database or a planning tool
configuration file. As long as the data is in a tabular format, with one row for each sector, Analyzer will be able to import the data.
CDMA Cell Site Parameters for Import:
Parameter Analyzer
Group
Analyzer Name Purpose
Site Name CDMA_Site SiteName Text description of the Site for display on map.
Site Number CDMA_Site SiteID Numeric identifier for the Site.
Latitude CDMA_Site Latitude Locates Site icons on map.
Longitude CDMA_Site Longitude Locates Site icons on map.
Sector Number CDMA_Cell Sector ID Sector-specific information useful for display on maps (can be alpha or numeric)
Azimuth CDMA_Cell Azimuth Orients the sector icons on the
map.
Beamwidth CDMA_Cell Beamwidth Governs the shape of the sector ‘wedge’ icon to reflect
the beamwidth of antenna deployed at the site.
PN Offset CDMA_Cell PN Used in CDMA Toolkit calculations, lines to neighbor cells and to color sector/site icons on maps to reflect PN planning.
Actix Analyzer Cell Site Data Technical Note June 2010 Importing Network Data 6
www.actix.com
2
Parameter Analyzer
Group
Analyzer Name Purpose
Base Station Power
CDMA_Cell EIRP Base station power, used in CDMA Toolkit calculations.
Mobile Country Code
CDMA_Cell MCC For information only.
System Identity CDMA_Cell SID For information only.
Network Identity CDMA_Cell NID For information only.
Broadcast Identity
CDMA_Cell BID For information only.
PctPilot CDMA_Cell PctPilot For information only.
PctTraffic CDMA_Cell PctTraffic For information only.
PctPaging CDMA_Cell PctPaging For information only.
PctSync CDMA_Cell PctSync For information only.
Active Set
Search Window Setting
CDMA_Cell SRCH_WIN_A Used in CDMA Toolkit calculations
to compare current search window settings with those suggested by Analyzer.
Neighbor Set Search Window Setting
CDMA_Cell SRCH_WIN_N Used in CDMA Toolkit calculations to compare current search window settings with those
suggested by Analyzer.
List of neighbors CDMA_Cell CDMANeighborList Used in CDMA Toolkit calculations to compare current neighbor list
settings to those suggested by Analyzer.
Sector Display – Wildcard
CDMA_Cell Face_Display Use to color sectors on the map by a custom integer field.
Sector Display – Wildcard
CDMA_Cell Azimuth_Display Use to color sectors on the map by a custom integer field.
Sector Display –
Wildcard
CDMA_Cell Phase_Display Use to color sectors on the map
by a custom integer field.
Layer Type CDMA_Cell LayerType Use this field to manage multiple cell layers to be displayed and
hidden separately.
Actix Analyzer Cell Site Data Technical Note June 2010 Importing Network Data 7
www.actix.com
2
The figure below is an example of a delimited CDMA file that could be used to import a site list into Analyzer. Though the columns can be in any order for import into Analyzer, the figure shows all of the REQUIRED
fields. Additionally, the Excel spreadsheet must be saved as a TEXT file for import into Analyzer.
Figure 1 - CDMA Cell Site Data Spreadsheet
2.2 Guidelines for Formatting Tabular Data Analyzer does not need the cell site data fields to be listed in a particular order, but to get the best results, follow these guidelines:
The Site ID field must contain a unique value for each site location. Beware of non-unique Site IDs – that is, entries that have multiple
sets of latitudes and longitudes for the same Site ID. Duplicated Site IDs will result in site markers appearing on the map without sector wedges. Site Names do not need to be unique – they are just
used for labeling purposes.
Position information must be accurate for Analyzer to correctly
display sites in the right location on the map. Longitudes that have a 'West' notation should be represented as a negative decimal value, as should latitudes with a 'South' notation. Sites will appear
skewed on the map if the latitude and longitude fields are transposed.
Actix Analyzer Cell Site Data Technical Note June 2010 Importing Network Data 8
www.actix.com
2
Before importing new cells into Analyzer, ensure that Analyzer is pointing to a valid cell site database.
A valid cell site database is a text file in which the first line contains the text below:
; #NetworkData – datafile
Every Analyzer installation comes with a clean file called
cellrefs.txt located in the directory called:
C:\Program Files\Actix\Analyzer\Bin\Cellrefs
The file to be populated need not be named “cellrefs.txt”. Rename
this file with a meaningful name in order to prevent the file from being overwritten during reinstallation.
To point the Analyzer to the file you wish to populate with the new cell site data, use the File Location line in the Tools > Preferences dialog. See the section on Loading Cell Site Data later in this document for more details.
2.3 Importing the Data Once you have obtained your cell site database in delimited format and
pointed Analyzer to a valid cellrefs file, you are ready to open the Network Explorer and import the site information.
1 To access the Network Explorer, select Cells > Network Explorer.
Figure 2 - Network Explorer Window
Actix Analyzer Cell Site Data Technical Note June 2010 Importing Network Data 9
www.actix.com
2
The Network Explorer display consists of two panels. The left panel contains a tree view of the network element data. The right panel shows details about relevant parameters for the current selection. If
you have pointed Analyzer to a cellrefs file containing only header information, you will not see any cell site data at this time.
2 From the toolbar, select Import > Import From New Template to open the Import dialog.
3 Select the appropriate network data file.
4 Click Open to display the Import Settings dialog.
Figure 3 - Import Settings Dialog (Step 1 of 2)
5 Give the Template a meaningful Template Name.
6 Check the appropriate Delimiter.
7 In most cases, the default information under the General Settings and Coordinate Information headers will apply. Adjust these settings if necessary.
8 Click Next.
Actix Analyzer Cell Site Data Technical Note June 2010 Importing Network Data 10
www.actix.com
2
Figure 4 - Settings (Step 2 of 2) – Assign CDMA_Site Data
9 Expand the CDMA_Site data node. Click in the Column field next to the Site_Name parameter. Select the parameter name from your site database that corresponds to the Site_Name parameter.
Repeat for each of the required fields in the CDMA_Site data node, based on the table below:
Field Mapping required for proper operation?
Site_Name Optional, but this field is frequently used for the site label.
SiteID Required, and this field must be unique for each site in the database.
Latitude Required
Longitude Required
Actix Analyzer Cell Site Data Technical Note June 2010 Importing Network Data 11
www.actix.com
2
Figure 5 - Column Settings (Step 2 of 2) – Assign CDMA_Cell Data
10 Expand the CDMA_Cell data node. Click in the Column field next to
the Sector_ID parameter. Select the parameter name from your site database that corresponds to the Sector_ID parameter. Repeat for
each of the required fields in the CDMA_Cell data node, based on
the table below:
Field Required for proper operation?
Sector_ID Required. This field can be used to color sectors on the map by face number (i.e. 1 = red, 2 = blue, 3 = green).
Azimuth Required
Beamwidth Required
EIRP Optional
PN Required
MCC Optional
SID Optional
NID Optional
Actix Analyzer Cell Site Data Technical Note June 2010 Importing Network Data 12
www.actix.com
2
Field Required for proper operation?
BID Optional
PctPilot Optional
PctTraffic Optional
PctPaging Optional
PctSync Optional
SRCH_WIN_A Optional
SRCH_WIN_N Optional
CDMANeighborList Optional
Face_Display Optional, but map this field to a custom integer field to color sectors on the map by that field. An example of a
custom field would be the phase of the site where:
1 = On Air
2 = Under Construction
3 = Planned for Next Year
Azimuth_Display Optional, but map this field to the integer azimuth field in order to color sectors on the map by azimuth range.
Phase_Display Optional, but map this field to a custom integer field to color sectors on the map by that field. An example of a
custom field would be the phase of the site where:
1 = On Air
2 = Under Construction
3 = Planned for Next Year
LayerType Optional. Use this field to manage multiple cell layers. Cells can be displayed or hidden on the map by layer.
11 Click Finish when all the columns have been assigned. If the current
workspace contains existing site data, you will be asked whether you want to remove existing data before importing new data. Select Yes to overwrite existing data. Select No to append to existing data.
12 If any errors occur during the import, a pop-up message will
indicate that an error log has been created. The error log specifies the cause of each error encountered and can be found in:
C:\Program Files\Actix\Analyzer\Bin\Cellrefs\ImportErrors.log
13 Inspect the cell data in the Network Explorer by expanding the All_CDMA_Site_Elements folder in the left-hand pane of the Network
Explorer.
14 Double-click on any site name in the right hand pane. The Name, Location and ID of the site will appear, as well as a folder containing CDMA Cell Elements. Drill into the CDMA Cell Elements
folder and examine the values corresponding to each sector.
15 To save the formatted site information, select the Save button.
Actix Analyzer Cell Site Data Technical Note June 2010 Importing Network Data 13
www.actix.com
2
16 Close the Network Explorer by clicking the “X” at the upper right hand corner.
17 After closing the Network Explorer, view a new map by selecting View > Display New Map.
18 If cell icons do not appear on the map, right click on the CDMA_Cell
layer in the map legend at the left hand side of the map window. Select Zoom to Layer to zoom the map to the appropriate location.
Be sure to close the map with the “X” at the upper right hand corner to save all changes to the map view.
Figure 6 - Use Zoom to Layer to Locate Cells on Map
If you see site markers appearing on the map
without sector wedges, this is probably due to non-unique Site IDs in the imported cell site data.
Sites can also appear skewed on the map if the latitude and longitude information has been
transposed.
Actix Analyzer Cell Site Data Technical Note June 2010 Importing Network Data 14
www.actix.com
2
2.4 Importing multiple technologies To be able to import multiple technologies using the same cellrefs file,
follow this procedure:
1 Import the first technology and save the cellrefs file.
2 Import the second technology and save that cellrefs file.
3 Using a text editor such as Windows Notepad, copy all of the second cellrefs file apart from the first line, and paste it in at the
end of the first cellrefs file.
You now have a cellrefs file that can import data for both technologies.
Actix Analyzer Cell Site Data Technical Note June 2010 Updating Cell Site Data 15
www.actix.com
2
3 Updating Cell Site Data
There are two convenient ways to update cell plan information in Analyzer:
Minor cell plan changes (a few azimuths, PNs, etc.) can be modified
directly from the Network Explorer. Simply browse to find the site
and sector of interest and double click on a single parameter to activate the text. Be sure to save the modifications before exiting
the Network Explorer!
If the cellplan file is updated (multiple sites added, complete
frequency retune), you can use the Automatic Import feature to detect changes to an existing cell plan and import the updated cell
site file into Analyzer.
Note that the Automatic Import feature will not
work with Spotlight.
3.1 Automatic Import of Cell Site Data The Automatic Import feature detects changes to cell plan data and
updates the configured site data every time Analyzer is opened.
Figure 7 - Automatic Import Setup
Actix Analyzer Cell Site Data Technical Note June 2010 Updating Cell Site Data 16
www.actix.com
2
Note that the Automatic Import feature will not work with Spotlight.
To use the Automatic Import feature:
1 From the Analyzer main menu, select Tools > Preferences.
2 Expand the Automatic Import option under Cellrefs and select the
Enable Automatic Import option.
3 Select the Automatic Import Input File (the text file that contains
your delimited site data).
4 Select the Automatic Import Template. Once a template has been
created, a new Analyzer workspace must be started in order for that template to appear in this list. To use a template created on
another computer, copy the template of interest from the C:\Program Files\Actix\Analyzer\Bin\Cellrefs\Templates directory to the
same directory on your machine.
5 Click OK to exit the Change Preferences dialog. A message will
appear that Automatic Import has been enabled and that your
currently loaded cellrefs will be overwritten the next time Analyzer
is restarted.
Once Automatic Import is configured, any changes to the Automatic Import Input File will be detected, and will be changed accordingly in your
Analyzer cell site file each time Analyzer is opened.
Actix Analyzer Cell Site Data Technical Note June 2010 Loading Cell Site Data 17
www.actix.com
2
4 Loading Cell Site Data
In order to display cell sites in Analyzer, and integrate cell site data with real-time measurements, a formatted cell site database must exist that
contains location and configuration data for each cell site. The previous section explained how to create a cell site file from a spreadsheet
containing network parameters. In Analyzer, the formatted cell site file is known as the „cellrefs‟ file, although this file can have any name.
Analyzer reads cell site data upon opening a new workspace. Therefore, if
any changes to cell site data are made, you must start a new workspace (or reopen Analyzer) in order for the changes to take effect.
Follow these steps to point Analyzer to a formatted cell site file:
1 From the main menu, select Tools > Preferences.
2 In the Change Preferences dialog, on the File Location line, click on
the name of the current cellrefs file.
3 In the Open dialog, navigate to the cellrefs file you would like to use and select Open.
4 Click OK to close the Preferences dialog.
5 A message box will be displayed saying that the new cellrefs file takes effect when a new workspace is loaded. Click OK to close the
message box. Analyzer loads cells upon opening Analyzer or starting a new workspace. From the Main Menu, choose File > New
Workspace to create a new workspace.
6 In the new workspace, click View > Display New Map. If cell icons do not appear on the map, right click on the CDMA_Cell layer in the
map legend at the left hand side of the map window. Select Zoom to
Layer to zoom the map to the appropriate location. Be sure to close
the map with the “X” at the upper right hand corner to save all
changes to the map view.
By default, the cell sites are now visible.
Actix Analyzer Cell Site Data Technical Note June 2010 Cell Site Display 18
www.actix.com
2
5 Cell Site Display
5.1 Displaying Site Labels By default, site and cell labels will be displayed on the map. You can leave the labels as they are, modify the way they are displayed, or turn them off entirely. The site labels are displayed independently of cell labels. This
allows you to display of Site Name or Site ID in addition to or instead of PN, Azimuth, or Beamwidth.
In Analyzer, “sectors” are called “cells” based on the European terminology.
The following instructions specify first site labeling, then cell labeling:
1 In the Layer Control dialog box, select the site layer (named
CDMA_Site-Site_Name)
2 Under the Properties heading in the Layer Control dialog, press the
Labels button.
3 The MapInfo-style Label Properties box will appear. Check each of
the following options:
▫ Show
▫ Allow overlapped text (recommended)
▫ Hide adjacent duplicate text (optional)
4 In the Label Properties box, use the drop down Data Field menu to
determine the label format to display. Currently, there are two formats of labels from which to choose:
▫ The Site_Name (default) shows only the site name.
▫ The KeyField label shows only the site ID.
5 If you wish to offset the label from the cell site symbol, use the options in the Position box in the Label Properties dialog.
6 If you wish to change the font of the labels, use the Label Style
button in the Properties dialog.
7 Select OK to exit the Label Properties dialog.
The Site Labels have been formatted. Next, format the Cell Labels:
1 In the Layer Control dialog box, select the cell layer (named CDMA_Cell-Beamwidth-PN)
2 Under the Properties heading in the Layer Control dialog, press the
Labels button
Actix Analyzer Cell Site Data Technical Note June 2010 Cell Site Display 19
www.actix.com
2
3 The MapInfo-style Label Properties box will appear. Check each of
the following options:
▫ Show
▫ Allow overlapped text (recommended)
▫ Hide adjacent duplicate text (optional)
4 In the Label Properties box, use the drop down Data Field menu to determine the label format to display. All CDMA_Cell parameters are
available as options for labeling.
5 The PN Label shows the PN for each sector, displayed next to the
sector. If you wish to offset the label from the cell site symbol, use the options in the Position box in the Label Properties dialog.
6 If you wish to change the font of the labels, use the Label Style
button in the Properties dialog.
7 Click OK in the Label Properties dialog, and then OK in the Layers
dialog to apply the labels.
Figure 8 – Labeled Sites on Map
Actix Analyzer Cell Site Data Technical Note June 2010 Cell Site Display 20
www.actix.com
2
5.2 Coloring Sectors on the Map By default, sectors are colored by PN on the map. To color the sectors
according to a different field (i.e. Sector_ID, to color sectors by face), or to make all sectors the same color:
1 Click the Cell Sites button at the top of the map.
2 In the Series drop-down, choose CDMA_Cell.
3 Use the Cell Color drop-down choose how to color the field. To make all sectors the same color, specify an unused field (i.e. MCC).
To color sectors by face (i.e. 1 = red, 2 = yellow, 3 = blue) choose Sector_ID.
4 Click OK to exit the Sites / Cell Properties dialog.
5 Site coloring will appear as specified. To modify face colors, expand
the CDMA_Cell parameter in the legend. Right-click on individual ranges and choose Selected Range’s Style to modify colors.
Figure 9 - Sites / Cell Properties Dialog
Note that the sector need not be colored and labeled by the same parameter. The figure below shows sectors colored by Sector_ID and labeled with the PN. Use the Layer Control dialog to adjust labeling as
desired.
Actix Analyzer Cell Site Data Technical Note June 2010 Cell Site Display 21
www.actix.com
2
Figure 10 - Sectors Colored by Sector_ID on Map
5.3 Searching for Cells Search for Cells provides a mechanism for locating specific cell sites based on user-defined search criteria.
To conduct a search:
1 Display site data of interest on the map.
2 From the main menu, select Cells > Search for Cells.
3 From the main menu, select Window > Tile Horizontally or Window >
Tile Vertically to arrange the CellRefs Search dialog and the map in
the workspace.
4 Ensure that CDMA is visible in the Technology drop-down.
5 Use the Add, Edit and Delete buttons to modify search criteria.
6 Click the Search Now button to show in the Results window all
matching cell sites from the current cellrefs file.
Actix Analyzer Cell Site Data Technical Note June 2010 Cell Site Display 22
www.actix.com
2
Figure 11 - CellRefs Search Dialog
7 From the Results window, select a row to highlight and center the
corresponding sector on the map.
8 Click the Highlight All button to highlight all matching sectors on the map.
Actix Analyzer Cell Site Data Technical Note June 2010 Cell Site Display 23
www.actix.com
2
Figure 12 - Map Highlighting All Sectors Meeting Search Criteria
5.4 Viewing Cell Site Information A cell‟s Azimuth, Beamwidth and Sector ID can be obtained by running the
mouse over a sector on the map.
To obtain more detailed information on each site or sector:
1 Display site data of interest on the map.
2 From the main menu, select Cells > Display Cell Data.
3 From the main menu, select Window > Tile Horizontally or
Window > Tile Vertically.
4 Click on a sector wedge or site dot on the map. Details about that
sector or site will appear in the Display Cell Data window.
Actix Analyzer Cell Site Data Technical Note June 2010 Cell Site Display 24
www.actix.com
2
Figure 13 - Display Cell Data Window
Actix Analyzer Cell Site Data Technical Note June 2010 Cell Site Display 25
www.actix.com
2
Appendix: CDMA Cell Site Parameters
Imported Parameter
Analyzer Group
Analyzer Name Purpose
Site Name CDMA_Site SiteName Text description of the Site for display on map.
Site Number
CDMA_Site SiteID Numeric identifier for the Site.
Latitude CDMA_Site SiteLatitude Locates Site icons on the map.
Longitude CDMA_Site SiteLongitude Locates Site icons on the
map.
Sector
Number
CDMA_Cell Sector ID
Can be 1,2,3 etc. or a combination of site numbers
Sector-specific
information useful for display on maps.
Azimuth CDMA_Cell Azimuth Orients the sector icons on the map.
Beamwidth CDMA_Cell Beamwidth Governs the shape of the sector 'wedge' on the
map to reflect the beamwidth of the antenna deployed at the
site.
PN Offset CDMA_Cell PN Used in CDMA Toolkit
calculations, lines to neighbor cells and to color sectors/sites on
maps to reflect PN planning.
Base Station Power*
CDMA_Cell EIRP Base station power, used in CDMA Toolkit calculations.
Mobile Country
Code*
CDMA_Cell MCC Mobile Country Code. For information only.
System Identity*
CDMA_Cell SID For information only.
Network Identity*
CDMA_Cell NID For information only.
Actix Analyzer Cell Site Data Technical Note June 2010 Cell Site Display 26
www.actix.com
2
Imported Parameter
Analyzer Group
Analyzer Name Purpose
Broadcast Identity*
CDMA_Cell BID For information only.
PctPilot* CDMA_Cell PctPilot For information only.
PctTraffic* CDMA_Cell PctTraffic For information only.
PctPaging* CDMA_Cell PctPaging For information only.
PctSync* CDMA_Cell PctSync For information only.
Active Set
Search Window Setting*
CDMA_Cell SRCH_WIN_A Used in Analyzer‟s CDMA
Toolkit calculations to compare current search window settings with
those suggested by Analyzer.
Neighbor Set Search Setting*
CDMA_Cell SRCH_WIN_N Used in Analyzer‟s CDMA Toolkit calculations to compare current search
window settings with those suggested by
Analyzer.
List of neighbors*
CDMA_Cell CDMANeighborList Used in Analyzer‟s CDMA Toolkit calculations to
compare current search window settings with
those suggested by Analyzer.
Sector
Display – Wildcard*
CDMA_Cell Face_Display Used to color sectors on
the map by a custom integer field.
Sector Display – Wildcard*
CDMA_Cell Azimuth_Display Used to color sectors on the map by a custom integer field.
Sector Display –
Wildcard*
CDMA_Cell Phase_Display Used to color sectors on the map by a custom
integer field.
Layer type* CDMA_Cell Layer_type Text that specifies which
cell layer (for example, by technology, band, purpose or status) that
the site belongs to. Used for multiple cell layers.
*Optional.
Actix Analyzer Cell Site Data Technical Note June 2010 Cell Site Display 27
www.actix.com
2
Appendix: GSM / GPRS / EDGE Cell Site Parameters
Imported
Parameter
Analyzer
Group
Analyzer
Name
Purpose
Site Name GSM_Site SiteName Text description of the Site
for display on map.
Site
Number
GSM_Site SiteID Numeric identifier for the
Site. Used as the linking column to associate the GSM_Site and GSM_Cell
rows.
Latitude GSM_Site Latitude Locates Site icons on map.
Longitude GSM_Site Longitude Locates Site icons on map.
Sector Number
GSM_Cell SectorID Can be 1,2,3,
etc, or a combination of
site numbers
Sector-specific ID information useful for display
on maps.
Azimuth GSM_Cell Azimuth Orients the sector icons on the map.
Beamwidth GSM_Cell Beamwith Governs the radius of the sector 'wedge' icon to reflect
the beamwidth of antenna deployed at the sector.
Base
Station Power
GSM_Cell EIRP Base Station Power.
Broadcast Control Channel
GSM_Cell BCCH Broadcast Control Channel.
Mobile Network
Code
GSM_Cell MNC Mobile Network Code.
Mobile Color Code
GSM_Cell MCC Mobile Color Code.
Location Area Code
GSM_Cell LAC Location Area Code.
Actix Analyzer Cell Site Data Technical Note June 2010 Cell Site Display 28
www.actix.com
2
Imported Parameter
Analyzer Group
Analyzer Name
Purpose
Cell ID value
GSM_Cell CI Cell ID value.
Base Station Identity
Code
GSM_Cell BSIC Base Station Identity Code, comprising of a concatenation of the NCC
and BCC values.
Layer type GSM_Cell Layer_type Text that specifies which cell
layer (for example, by technology, band, purpose or status) that the site
belongs to. Used for multiple cell layers.
Actix Analyzer Cell Site Data Technical Note June 2010 Cell Site Display 29
www.actix.com
2
Appendix: iDEN Cell Site Parameters
Imported Parameter
Analyzer Group
Analyzer Name
Purpose
Site Name IDEN_Site SiteName Text description of the Site for display on map.
Site Number
IDEN_Site SiteID Numeric identifier for the Site.
Latitude IDEN_Site Latitude Locates Site icons on map.
Longitude IDEN_Site Longitude Locates Site icons on map.
Sector
Number
IDEN_Cell Sector ID Can
use 1,2,3, etc, or a
combination of site numbers
Sector-specific information
useful for display on maps.
Azimuth IDEN_Cell Azimuth Orients the sector icons on
the map.
Beamwidth IDEN_Cell Beamwidth Governs the shape of the
sector 'wedge' icon to reflect the beamwidth of antenna
deployed at the site.
Base Station
Power
IDEN_Cell EIRP Base Station Power.
Common
Control Channel
IDEN_Cell CCCH Can be used to color the
sector wedges.
Color Codes IDEN_Cell Color_Codes A list of color codes
separated by semicolons. This list is designed to match
the entries in the TCH_List field. Used for determining likely serving and neighbor
cells.
Digital
Control Channel
IDEN_Cell DCCH Digital Control Channel.
Digital Voice
Color Code
IDEN_Cell DVCC Digital Voice Color Code.
Actix Analyzer Cell Site Data Technical Note June 2010 Cell Site Display 30
www.actix.com
2
Imported Parameter
Analyzer Group
Analyzer Name
Purpose
Traffic Channel List
IDEN_Cell TCH_List A list of traffic channels, separated by semicolons.
This list is designed to match the entries in the Color_Codes field. Used for
determining likely serving and neighbor cells.
Mobile Country Code
IDEN_Cell MCC Mobile Country Code.
Cell Identity IDEN_Cell CI Cell Identity.
Layer type IDEN_Cell Layer_type Text that specifies which cell
layer (for example, by technology, band, purpose or status) that the site
belongs to. Used for multiple cell layers.
Actix Analyzer Cell Site Data Technical Note June 2010 Cell Site Display 31
www.actix.com
2
Appendix: LTE Cell Site Parameters
Imported Parameter
Analyzer Group
Analyzer Name
Purpose
Site Name LTE_Site Site_Name Text description of the Site for display on map.
Site Number LTE_Site SiteID Numeric identifier for the site.
Latitude LTE_Site Latitude Locates site icons on map.
Longitude LTE_Site Longitude Locates site icons on map.
Sector Number
LTE_Cell Sector_ID Sector-specific information useful for display on maps (can
be alpha or numeric)
Azimuth LTE_Cell Azimuth Orients the sector icons on the
map.
Beamwidth LTE_Cell Beamwidth Governs the shape of the sector “wedge” icon to reflect
the beamwidth of antenna deployed at the site.
EIRP* LTE_Cell EIRP Equivalent Isotropic Radiated Power – for informational
purposes only.
Downlink EARFCN
LTE_Cell DL_EARFCN The downlink EARFCN of the cell. The fields DL_EARFCN and
PCI must be present to calculate lines to cells
Layer1 Cell Identity
LTE_Cell PCI The physical layer cell identity (formerly named L1_CID). The fields DL_EARFCN and PCI
must be present to calculate lines to cells.
MCC* LTE_Cell MCC Mobile Country Code – for informational purposes only.
MNC* LTE_Cell MNC National Domain Code – for
informational purposes only.
* Optional.
Actix Analyzer Cell Site Data Technical Note June 2010 Cell Site Display 32
www.actix.com
2
Appendix: UMTS / HSPA+ Cell Site Parameters
Imported Parameter
Analyzer Group
Analyzer Name Purpose
Site Name UMTS_Site SiteName Text description of the Site for display on map.
Site Number
UMTS_Site SiteID Numeric identifier for the site.
Latitude UMTS_Site Latitude Locates site icons on map.
Longitude UMTS_Site Longitude Locates site icons on
map.
Sector
Number
UMTS_Cell Sector_ID Sector-specific
information useful for display on maps (can be alpha or numeric)
Azimuth UMTS_Cell Azimuth Orients the sector icons on the map.
Beamwidth UMTS_Cell Beamwidth Governs the shape of the sector “wedge” icon to
reflect the beamwidth of antenna deployed at the site.
SC UMTS_Cell SC Used for cell site identification and to
calculate lines to cells.
EIRP* UMTS_Cell EIRP Equivalent Isotropic Radiated Power – for
informational purposes only.
MCC* UMTS_Cell MCC Mobile Country Code – for informational purposes only.
MNC* UMTS_Cell MNC National Domain Code – for informational
purposes only.
LAC* UMTS_Cell LAC Location Area Code – for informational purposes
only.
Actix Analyzer Cell Site Data Technical Note June 2010 Cell Site Display 33
www.actix.com
2
Imported Parameter
Analyzer Group
Analyzer Name Purpose
CI* UMTS_Cell CI Cell Identity – for informational purposes
only.
Neighbor List*
UMTS_Cell WCDMANeighborList Used to define a pre-defined neighbor list for
each cell. Used during neighbor list
recommendations analysis.
Layer
Type*
UMTS_Cell LayerType Configurable text field
that specifies which cell layer (for example, by
technology, band or status) the site belongs to. Used for multiple cell
layers.
* Optional.
Actix Analyzer Cell Site Data Technical Note June 2010 Cell Site Display 34
www.actix.com
2