4.electronics production (feb 15)
DESCRIPTION
4.electronics production (Feb 15)WALTER GONZALES ARNAOTRANSCRIPT
![Page 1: 4.electronics production (feb 15)](https://reader034.vdocument.in/reader034/viewer/2022042623/5472a611b4af9fc30a8b4f8a/html5/thumbnails/1.jpg)
Fab academy 2012
4.electronics production (Feb 15) STUDENT: WALTER HECTOR GONZALES ARNAO
UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
![Page 2: 4.electronics production (feb 15)](https://reader034.vdocument.in/reader034/viewer/2022042623/5472a611b4af9fc30a8b4f8a/html5/thumbnails/2.jpg)
Fab academy
summary -This week assigment is to make a FabISP. -using Roland MDX-20 Milling Machine -for this we will have to programmer in-circuit -then assemble the SMD components, test for shorts or open circuits and then test and program the FabISP. CLASS 4: electronics production (Feb 15)
UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
![Page 3: 4.electronics production (feb 15)](https://reader034.vdocument.in/reader034/viewer/2022042623/5472a611b4af9fc30a8b4f8a/html5/thumbnails/3.jpg)
Fab academy
FIRST STEP. WILL WORK WITH THE BOART CLASS 4: electronics production (Feb 15)
UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
![Page 4: 4.electronics production (feb 15)](https://reader034.vdocument.in/reader034/viewer/2022042623/5472a611b4af9fc30a8b4f8a/html5/thumbnails/4.jpg)
Fab academy
STEP 2. -Then we setup the MDX-20, -Installing the board on the milling table and also the milling tool (1/32" for cutting and 1/64" for milling). CLASS 4: electronics production (Feb 15) UNIVERSIDAD NACIONAL DE INGENIERÍA
FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
![Page 5: 4.electronics production (feb 15)](https://reader034.vdocument.in/reader034/viewer/2022042623/5472a611b4af9fc30a8b4f8a/html5/thumbnails/5.jpg)
Fab academy 2012 STEP 3.
Downloading files, CLASS 4: electronics production (Feb 15)
UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
![Page 6: 4.electronics production (feb 15)](https://reader034.vdocument.in/reader034/viewer/2022042623/5472a611b4af9fc30a8b4f8a/html5/thumbnails/6.jpg)
Fab academy 2012 STEP 4.
-Tools and materials, such as: soldering station, solder wire, third hand with magnifying loupe, tweezers and rosin flux
UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
![Page 7: 4.electronics production (feb 15)](https://reader034.vdocument.in/reader034/viewer/2022042623/5472a611b4af9fc30a8b4f8a/html5/thumbnails/7.jpg)
Fab academy 2012 STEP 5.
PRESENTED PROBLEMS TO FIND THE FILES to run IN BOART, BUT AT THE END OF PLACING PROPERLY CLASS 4: electronics production (Feb 15)
UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
![Page 8: 4.electronics production (feb 15)](https://reader034.vdocument.in/reader034/viewer/2022042623/5472a611b4af9fc30a8b4f8a/html5/thumbnails/8.jpg)
Fab academy 2012
STEP 6. -upon completion of the construction of the card - Then following the tutorial I installed the AVR programming software and downloaded the firmware.zip file for programming the FabISP. -Testing and programming the FabISP CLASS 4: electronics production (Feb 15)
UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
![Page 9: 4.electronics production (feb 15)](https://reader034.vdocument.in/reader034/viewer/2022042623/5472a611b4af9fc30a8b4f8a/html5/thumbnails/9.jpg)
Fab academy 2012
STEP 7.SE turned on the LET CLASS 4: electronics production (Feb 15)
UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
Conclusions. conclusions 1. This has been a hardwork, especially . We had to calibrate the table of the milling machine, 2. When connected the ATTiny to the programmer, first we got a red light, so with the multimeter we measured the voltage supply of the ATTiny and found a short circuit, wich was fixed. 3. I asked for help to our colleagues, for the programming, the support was Roberto.