65273 infinity extra vision showcase - store supply · track and slide to the left. insert right...

ASSEMBLY INSTRUCTIONS MANUAL65273 (36” W) INFINITY EXTRA VISION SHOWCASE

A. #65288 WITH LIGHTS (P. 1-11)B. WITHOUT LIGHTS (P. 12-20)

PAGE 1 OF 20

BOX WRENCH(FOR ADJUSTING BASE NUT LEVELS)

ALLEN WRENCH

PARTS IN CARTON:

RECOMMENDED TOOLS FOR ASSEMBLY:

(2) KEYS

ALLEN WRENCH SCREWS(26 EACH / 2 ARE 1” FOR LIGHT BARS )

PLASTIC WASHERS(19 EACH)

PHILLIPS SCREW DRIVER(BOX WRENCH AND ALLEN WRENCH INCLUDED)

U-SHAPEDCORNER BRACKETS

(2 EACH)

L-SHAPEDBOTTOM BRACKETS

(6 EACH)THREADED ON ONE SIDE

MALLET

TOP GLASS DOOR ALUMINUM SLIDE BARTOP BAR SET NUTS (3 EACH)

GLUE

L-SHAPEDFRONT BACK BRACKETS

(2 EACH)THREADED ON TWO SIDES

METAL WASHERS(4 EACH)

NUTS(2 EACH)

CLEAR BUMPER TABS

(8 EACH)

GLASS DOOR PLASTIC TOP SLEEVES (2 EACH)

GLASS DOOR METAL BOTTOM SLEEVE (WITH LOCK)

GLASS DOOR METAL BOTTOM SLEEVE (WITH LOCK HOLE) PAGE 2 OF 20

ASSEMBLY INSTRUCTIONS MANUAL#65273/288 (36” W) INFINITY EXTRA VISION SHOWCASE W/LIGHTS

LIGHT BAR(2 EACH)

CAREFULLY REMOVE CABINET PIECES FROMPACKING. CABINET SETUP INCLUDES:

- BACK GLASS / TOP GLASS- (2) SIDE GLASS (LEFT & RIGHT)- (2) GLASS DOORS- (2) GLASS SHELVES- (2) LIGHT BARS- LIGHT ADAPTOR & AC ADAPTOR / POWER CHORD- CABINET BASE WITH ROLLERS (PRE-ASSEMBLED)

PARTS IN CARTON:

AC ADAPTOR & POWER CHORD

WOOD SCREWS(4 EACH)

LIGHT ADAPTOR

PAGE 3 OF 20


* IN STEPS 1 THROUGH 8 OF THE ASSEMBLY - TWO PEOPLE ARE RECOMMENDED

STEP 1. PLACE BASE ON IT’S SIDE (PREFERABLY LONG/FRONT SIDE FOR STABILITY).INSERT LIGHT BAR THROUGH THROUGH WASHERS, THEN LIGHT BAR HOLES AND SECURE WITH WASHER AND NUT ON BOTTOM SIDE OF BASE WITH BOX WRENCH (PROVIDED).

*NOTE - MAKE SURE LIGHT BARS ARE FACING INWARD - TOWARDS MIDDLE OF BASE.

BASE

LIGHT BAR

LIGHT BAR HOLES

LIGHT BAR HOLE

LIGHT BAR HOLE

BASE PLACED ON IT’S SIDE

BASE

PAGE 4 OF 20


STEP 2. WITH BASE ON IT’S SIDE, ATTACH LIGHT ADAPTOR TO BASE WITH WOOD SCREWS USING A SCREWDRIVER. ATTACH LIGHT ADAPTOR END TO LIGHT BARS (2).

STEP 3. ATTACH LIGHT ADAPTOR TO AC ADAPTOR/POWER CHORD. WE RECOMMENDTHAT YOU ATTACH IT TO THE BASE USING TWO WAY TAPE (NOT PROVIDED). OTHERWISE LET REST ON THE FLOOR.

WOOD SCREWS(2 EACH)

UNDERSIDE OF BASE

LIGHT BAR

OPENING (PRE-CUT) IN BASE

WOOD SCREWS(2 EACH)

LIGHT ADAPTOR

AC ADAPTOR

POWER CHORD

PAGE 5 OF 20


IMPORTANTBOTTOM OF FRONT BACK AND SIDE GLASS HAS A SLIGHTLY DIFFERENT

HOLE PLACEMENT THAN THE TOP OF EACH PIECE OF GLASS

MEASURE THE GLASS SPACE BETWEEN EDGE OF GLASS AND CENTER OF HOLE.HOLE FURTHEST FROM EDGE GOES ON BOTTOM.

GLASS CAN ONLY BE ASSEMBLED ONE WAY!

FRONT BOTTOM SIDE BOTTOM (FRONT)

1 3/4” 2”

PAGE 6 OF 20


STEP 4. PLACE FRONT GLASS PANEL INTO FRONT GROOVE OF CABINET BASE. MAKE SURE GLASS PRECISELY FITS FRONT BASE GROOVE IN ORDER TO ACCOMODATE THE SIDE PANELS NEXT. MAKE CERTAIN ON BOTH FRONT AND SIDE PANELS THAT YOU RECOGNIZE THE BOTTOM OF EACH PANEL CORRECTLY. (SEE PAGE 7)

STEP 5. PLACE LEFT SIDE GLASS INTO BASE GROOVE WHILE HOLDING FRONT GLASS TO LINE UP FIRST GLASS BRACKET. ATTACH U-BRACKET WITH ALLEN WRENCH SCREWS AND WASHERS.

STEP 6. REPEAT STEP 5 FOR RIGHT SIDE GLASS.

HAND SCREW IN ALL CORNER HARDWARE. DO NOT TIGHTEN WITH ALLEN WRENCH YET. THIS ALLOWS FLEXIBILITY UNTIL ASSEMBLY IS NEARLY COMPLETE.

4

5

6

U-SHAPEDCORNER BRACKET

U-SHAPED CORNER

BRACKET

ALLEN WRENCH SCREWS& PLASTIC WASHERS

L-SHAPED BOTTOMBRACKETS (4)(THREADED ON ONE SIDE)

L-SHAPED TOP BRACKETS (2)(THREADED ON TWO SIDES)

PAGE 7 OF 20


STEP 7. SCREW FLAT HEAD BOLTS INTO CHROME CYLINDERS - PLACE RUBBER GROMMETS INTO HOLES (THIS SUPPORTS GLASS SHELF). (8) CLYLINDERS ALL TOGETHER (4 FOR EACH SHELF).

*NOTE - MAKE SURE RUBBER GROMMETS ARE FACING UP TO SUPPORT GLASS SHELVES.

RUBBERGROMMET

CHROMECYLINDER

FLAT HEAD BOLT


PAGE 8 OF 20

TWO PERSON ASSEMBLYSTEP 8. CAREFULLY SLIDE TOP GLASS ONTO CABINET MAKING SURE YOU HAVE AN OVERLAP ON BOTH SIDES.

STEP 9. SCREW ALLEN SCREWS INTO BOTH U-BRACKETS AND L-BRACKETS ON TOP. (TIGHTEN ALL SCREWS BEFORE ASSEMBLING SHELVES. DO NOT OVER TIGHTEN)

STEP 10. PLACE GLASS SHELVES INTO CABINET.

STEP 11. PLACE TOP GLASS DOOR ALUMINUM SLIDE GUIDE UNDER TOP GLASS. BEGIN WITH CENTER SCREW FIRST AND THEN EACH END.

IT IS EASIER TO INSERT SCREW INSIDE OF GUIDE BY PUTTING SCREW ON ALLEN WRENCH AND THEN THROUGH GUIDE AND GLASS.

1” SCREWS FOR LIGHT BARS

81” SCREWS

FOR LIGHT BARS

9

10


PAGE 9 OF 20

TOP

STEP 12. INSTALLING SLIDING GLASS DOORS. PLACE CLEAR PLASTIC SLEEVES ON TOP OF GLASS DOORS. TAP ON SLEEVES WITH RUBBER MALLET.

RUN BEAD OF ANY TYPE OF GLUE ON INSIDE (BOTTOM) OF TOP PLASTIC SLEEVE. THEN TAP SLEEVES ON

TOP OF THE GLASS WITH A RUBBER MALLET.

THIS PREVENTS THE SLEEVES FROM MOVING ONCE ASSEMBLY IS COMPLETE AND DOORS ARE MOVED.

PLACE METAL SLEEVES (WITH LOCK TO THE LEFT) ON BOTTOM OF GLASS DOORS. TAP ON SLEEVES WITH RUBBER MALLET.

BOTTOM

RUN BEAD OF ANY TYPE OF GLUE ON INSIDE (TOP) OF BOTTOM METAL SLEEVE. THEN TAP SLEEVES ON

BOTTOM OF THE GLASS WITH A RUBBER MALLET.



PAGE 10 OF 20

BOTTOM TRACK

STEP 13. INSERT LEFT DOOR (WITHOUT LOCK - MAKE SURE HOLE IN BOTTOM METAL SLEEVE IS FACING YOU / ON THE RIGHT) INTO TOP OF BACK TRACK, THEN LOWER INTO BOTTOM BACK TRACK AND SLIDE TO THE LEFT.

INSERT RIGHT DOOR (INSTALLED LOCK ASSEMBLY ON THE LEFT) INTO TOP OF FRONT TRACK, THEN LOWER INTO BOTTOM FRONT TRACK AND SLIDE TO THE RIGHT.

THIS COMPLETES THE ASSEMBLY.


PAGE 11 OF 20

OF 20

ASSEMBLY INSTRUCTIONS MANUAL#65273 (36” W) INFINITY EXTRA VISION SHOWCASE

BOX WRENCH(FOR ADJUSTING BASE NUT LEVELS)

ALLEN WRENCH

PARTS IN CARTON:

RECOMMENDED TOOLS FOR ASSEMBLY:

(2) KEYS

ALLEN WRENCH SCREWS(26 EACH / 2 ARE 1” FOR LIGHT BARS )

PLASTIC WASHERS(19 EACH)

PHILLIPS SCREW DRIVER(BOX WRENCH AND ALLEN WRENCH INCLUDED)

U-SHAPEDCORNER BRACKETS

(2 EACH)

L-SHAPEDBOTTOM BRACKETS

(6 EACH)THREADED ON ONE SIDE

MALLET

TOP GLASS DOOR ALUMINUM SLIDE BARTOP BAR SET NUTS (3 EACH)

GLUE

L-SHAPEDFRONT BACK BRACKETS

(2 EACH)THREADED ON TWO SIDES

CLEAR BUMPER TABS

(8 EACH)

GLASS DOOR PLASTIC TOP SLEEVES (2 EACH)

GLASS DOOR METAL BOTTOM SLEEVE (WITH LOCK)

GLASS DOOR METAL BOTTOM SLEEVE (WITH LOCK HOLE) PAGE 13 OF 20


CAREFULLY REMOVE CABINET PIECES FROM PACKING. CABINET SETUP INCLUDES:

- BACK GLASS / TOP GLASS- (2) SIDE GLASS (LEFT & RIGHT)- (2) GLASS DOORS- (2) GLASS SHELVES- CABINET BASE WITH ROLLERS (PRE-ASSEMBLED)

PARTS IN CARTON:

PAGE 14 OF 20


IMPORTANTBOTTOM OF FRONT BACK AND SIDE GLASS HAS A SLIGHTLY DIFFERENT

HOLE PLACEMENT THAN THE TOP OF EACH PIECE OF GLASS

MEASURE THE GLASS SPACE BETWEEN EDGE OF GLASS AND CENTER OF HOLE.HOLE FURTHEST FROM EDGE GOES ON BOTTOM.

GLASS CAN ONLY BE ASSEMBLED ONE WAY!

FRONT BOTTOM SIDE BOTTOM (FRONT)

1 3/4” 2”

PAGE 15 OF 20


* IN STEPS 1 THROUGH 8 OF THE ASSEMBLY - TWO PEOPLE ARE RECOMMENDED

STEP 1. PLACE FRONT GLASS PANEL INTO FRONT GROOVE OF CABINET BASE. MAKE SURE GLASS PRECISELY FITS FRONT BASE GROOVE IN ORDER TO ACCOMODATE THE SIDE PANELS NEXT. MAKE CERTAIN ON BOTH FRONT AND SIDE PANELS THAT YOU RECOGNIZE THE BOTTOM OF EACH PANEL CORRECTLY. (SEE PAGE 7)

STEP 1. PLACE LEFT SIDE GLASS INTO BASE GROOVE WHILE HOLDING FRONT GLASS TO LINE UP FIRST GLASS BRACKET. ATTACH U-BRACKET WITH ALLEN WRENCH SCREWS AND WASHERS.

STEP 3. REPEAT STEP 5 FOR RIGHT SIDE GLASS.

HAND SCREW IN ALL CORNER HARDWARE. DO NOT TIGHTEN WITH ALLEN WRENCH YET. THIS ALLOWS FLEXIBILITY UNTIL ASSEMBLY IS NEARLY COMPLETE.

1

2

3

U-SHAPEDCORNER BRACKET

U-SHAPED CORNER

BRACKET

ALLEN WRENCH SCREWS& PLASTIC WASHERS

L-SHAPED BOTTOMBRACKETS (4)(THREADED ON ONE SIDE)

L-SHAPED TOP BRACKETS (2)(THREADED ON TWO SIDES)

PAGE 16 OF 20


STEP 4. SCREW FLAT HEAD BOLTS INTO CHROME CYLINDERS - PLACE RUBBER GROMMETS INTO HOLES (THIS SUPPORTS GLASS SHELF). (8) CLYLINDERS ALL TOGETHER (4 FOR EACH SHELF).

*NOTE - MAKE SURE RUBBER GROMMETS ARE FACING UP TO SUPPORT GLASS SHELVES.

RUBBERGROMMET

CHROMECYLINDER

FLAT HEAD BOLT

PAGE 17 OF 20


TWO PERSON ASSEMBLYSTEP 5. CAREFULLY SLIDE TOP GLASS ONTO CABINET MAKING SURE YOU HAVE AN OVERLAP ON BOTH SIDES.

STEP 6. SCREW ALLEN SCREWS INTO BOTH U-BRACKETS AND L-BRACKETS ON TOP. (TIGHTEN ALL SCREWS BEFORE ASSEMBLING SHELVES. DO NOT OVER TIGHTEN)

STEP 7. PLACE GLASS SHELVES INTO CABINET.

STEP 8. PLACE TOP GLASS DOOR ALUMINUM SLIDE GUIDE UNDER TOP GLASS. BEGIN WITH CENTER SCREW FIRST AND THEN EACH END.

IT IS EASIER TO INSERT SCREW INSIDE OF GUIDE BY PUTTING SCREW ON ALLEN WRENCH AND THEN THROUGH GUIDE AND GLASS.

56

7

PAGE 18 OF 20


TOP

STEP 9. INSTALLING SLIDING GLASS DOORS. PLACE CLEAR PLASTIC SLEEVES ON TOP OF GLASS DOORS. TAP ON SLEEVES WITH RUBBER MALLET.

RUN BEAD OF ANY TYPE OF GLUE ON INSIDE (BOTTOM) OF TOP PLASTIC SLEEVE. THEN TAP SLEEVES ON

TOP OF THE GLASS WITH A RUBBER MALLET.


PLACE METAL SLEEVES (WITH LOCK TO THE LEFT) ON BOTTOM OF GLASS DOORS. TAP ON SLEEVES WITH RUBBER MALLET.

BOTTOM

RUN BEAD OF ANY TYPE OF GLUE ON INSIDE (TOP) OF BOTTOM METAL SLEEVE. THEN TAP SLEEVES ON

BOTTOM OF THE GLASS WITH A RUBBER MALLET.


PAGE 19 OF 20


BOTTOM TRACK

STEP 10. INSERT LEFT DOOR (WITHOUT LOCK - MAKE SURE HOLE IN BOTTOM METAL SLEEVE IS FACING YOU / ON THE RIGHT) INTO TOP OF BACK TRACK, THEN LOWER INTO BOTTOM BACK TRACK AND SLIDE TO THE LEFT.

INSERT RIGHT DOOR (INSTALLED LOCK ASSEMBLY ON THE LEFT) INTO TOP OF FRONT TRACK, THEN LOWER INTO BOTTOM FRONT TRACK AND SLIDE TO THE RIGHT.

THIS COMPLETES THE ASSEMBLY.

PAGE 20 OF 20


65273 infinity extra vision showcase - store supply · track and slide to the left. insert right...

Documents