670/650 series and sam600-io iec accessories€¦ · x x 0 4 0 0 0 4 5 3 . v s d 1 2 3 4 5 6....

Relion® SERIES

670/650 series and SAM600-IO IECAccessories

Contents

1. Available accessories...........................................................3

2. Mounting kits........................................................................ 3

3. RHGS cases............................................................................5

4. Test switch module............................................................. 6

5. Key switch for settings....................................................... 7

6. Combiflex modules..............................................................7

7. Connectors............................................................................ 8

8. External resistor unit...........................................................9

9. External current transformer unit..................................10

10. Interface converter............................................................ 11

11. GPS antenna........................................................................11

12. Injection unit REX060.......................................................13

13. Coupling capacitor unit REX061....................................13

14. Shunt resistor unit REX062............................................ 15

15. Voltage injection unit RXTTE4........................................17

16. ESD Field Kit....................................................................... 19

17. Power Supply......................................................................19

18. Configuration and monitoring tools........................... 19

19. Cable and dust cover........................................................19

20. MicroScada tools..............................................................20

21. User interface.................................................................... 20

22. Ordering.............................................................................. 21

23. Related documents..........................................................29

Disclaimer

The information in this document is subject to change without notice and should not be construed as a commitment by ABB. ABB assumes no

responsibility for any errors that may appear in this document. Drawings and diagrams are not binding.

© Copyright 2017 ABB. All rights reserved.

Trademarks

ABB and Relion are registered trademarks of the ABB Group. All other brand or product names mentioned in this document may be trademarks or

registered trademarks of their respective holders.

670/650 series and SAM600-IO IEC 1MRK 514 012-BEN H

2 ABB

1. Available accessories

Mounting kitsM1831-1 v3

• Mounting kits for space-saving mounting in racks,cubicles or on walls

• IP54 protected mounting capability in cubicles for 670and 650 series

RHGS casesSEMOD121070-2 v2

• RHGS 6, RHGS 12 and RHGS 30 cases enable mountingof for example Combiflex modules

Test switch moduleM1947-1 v2

• Fail-safe testing of IEDs, using test switch RTXP 24• Time saving while

– all connections for test are made from the front– easy to move between IEDs of the same type

Combiflex modulesSEMOD121075-2 v2

• Provide functionality such as lock-out, lock-out resetand external contact re-enforcement

• Supervision

Key switch for settingsM1990-1 v1

• Possibility to lock settings with key switch

ConnectorsM1997-1 v2

• Flexible connection of analog and binary signals– Screw compression type– Terminal blocks suitable for ring-lugs

External resistor unitSEMOD120184-10 v2

• Used with the High impedance differential protection

External current transformer unitSEMOD121078-2 v2

• Used for cost effective summation type differentialprinciple

Interface converterM1780-1 v2

• External interface converter from C37.94 to G703• External interface converter from C37.94 to G703.E1

GPS antennaSEMOD121065-2 v2

• Used with the GPS time synchronization module GTM(or GSM)

Injection equipment hardware REX060, REX061,REX062

GUID-F6C11BE9-F5C7-4378-A3F0-9437B715E48A v1

• Is used to inject voltage and current signals to thegenerator or motor.

COMBIFLEX Injection equipmentGUID-BFA755D6-9CE7-4342-B4F9-4E4F525A554A v2

RXTTE4 and optional protective resistor are used toinject fundamental frequency AC voltage into the rotorcircuit.

ESD Field KitGUID-9C991E88-4B0E-4B1A-877A-F85E1ED192E1 v1

• Used to make work ESD safe

Power SupplyGUID-2613CBA7-B7D0-4037-A3FA-01CB0DC14C40 v1

• Used to supply power to the IED

Configuration and monitoring toolsSEMOD124331-1 v1M1890-1 v2

• Protection and control manager, PCM600, used to– configure the IED– set parameters– monitor the IED and the system– visualize and evaluate disturbance recordings

M2078-1 v2

• Supervision and control of the power system via IEDs(HV/Control package)

• Provides on request information from IEDs• Collection of disturbances from IEDs• Consists of standard library functions for easy

application engineering of a station HMI

Cable and dust coverGUID-17E99276-BE53-4D03-A6D8-B926C5F81F8F v1

• The cable is used to connect a PC to the RJ45 port onthe local human machine interface

• The dust cover protects the RJ45 port

LabelsGUID-9F23A29B-E379-4705-A87F-3D9308354974 v1

• Used to label the LEDs

SAM600-IO LHMI service kitGUID-DA06ABEE-FAC7-4C7D-8912-A03FDDBEAA1D v2

• The SAM600-IO LHMI service kit is a support tool forSAM600-IO during:– Troubleshooting– Commissioning– Service– Maintenance

2. Mounting kits

19” rack mountingIP653-1 v1M1835-3 v3

Use the 19" rack mounting kit for 6U housing to mountthe IED in a standard rack. Combine the rack mountingkit with the side-by-side mounting kit to mount IEDs oran IED and a test switch module in the same rackposition.

M1840-3 v2

The 19" rack mounting kit is available in four designs,suitable for 1/4, 1/2, 3/4 or full width cases and consists

670/650 series and SAM600-IO IEC 1MRK 514 012-BEN HIssued: May 2019

Revision: H

ABB 3© Copyright 2017 ABB. All rights reserved

of two rack flanges (1a) and (1b) with appropriatemounting details (2) for fastening to the case.

IEC04000452-3-en.vsd

1b

1a

2

3

IEC04000452 V3 EN-US

Figure 1. The rack mounting kit

Flush mounting for 670 and 650 seriesIP652-1 v2M1929-3 v2

Use the flush mount kit for installation in a panel cut-out.

M1938-3 v2

The flush mounting kit for release 2.1 and earlierconsists of four fasteners (2) with appropriate mountingdetails (4) and a sealing strip (5) for fastening to the IED(3). See Figure 2.

From release 2.2 onwards, the flush mounting kitconsists of two fasteners (2) with appropriate mountingdetails (4) and a sealing strip (5) for fastening to the IED(3). See Figure 3. The two fasteners are pre-assembledto the box.

To receive IP54 class protection, an additional sealing (1)must be ordered with the IED. This sealing is factorymounted.

IEC04000451-2-en.vsdIEC04000451 V2 EN-US

Figure 2. The flush mounting kit (release 2.1 and earlier)

1

5

6

3

IEC16000080=1=en.vsd

2

4


Figure 3. The flush mounting kit (release 2.2 onwards)

Wall mounting for 670 and 650 seriesIP651-1 v2M1974-3 v1

Use the wall mounting kit to projection mount the IEDon a wall.

M1973-3 v1

The wall mounting kit consists of a mounting bar pair(4) and a IED bracket pair (6). Screws (2) and (5) andwashers (1) for fastening of the terminal are included,but not wall fasteners (3).


4 ABB© Copyright 2017 ABB. All rights reserved

xx04000453.vsd

1

2

3

4

5

6


Figure 4. The wall mounting kit

Wall mounting for SAM600-IOGUID-2C7B44A9-6E63-4859-B20C-6EB36A9E0170 v1

Use the wall mounting kit to projection mount theSAM600-IO on a wall, see figure 5.

The wall mounting kit consists of 8 washers (1), 8 screws(2), 2 mounting profiles (3), 6 nuts (4), 4 spacers (5) and2 mounting angles (6).

To order wall mounting kit, refer to section Mountingaccessories.

For more details on wall mounting, refer to Installationmanual.

1

2

3

4

56

IEC17000054-1-en.vsdx


Figure 5. Wall mounting details

Side-by-side mounting

IP649-1 v1M1970-3 v1

Use the side-by-side mounting kit to mount two IEDs ora IED and its corresponding test switch module next toeach other.

M1965-3 v3

The side-by-side mounting kit consists of two mountingplates with appropriate mounting details (1 and 2). Theside-by-side mounted units are mounted in a rack orcubicle using the appropriate kit; in this example, therack mounting kit (3) is used.

IEC040004563enOriginal.vsdx

1

2

3

4

3


Figure 6. The side-by-side mounting kit

Protection cover for rear areaM10592-3 v1

The protection cover for the rear area is a steel coverwith a slot for cable entrance at the bottom part.



Figure 7. Protection cover for rear area

3. RHGS cases

RHGS CasesSEMOD121089-4 v2

Color matched (RAL7035) RHGS cases can be used tomount for example Combiflex modules together with670 series. See section "Related documents" forreference to more detailed information about



dimensions. Please observe that cases in referenceddocument has a different color.

4.

Test switch module

GeneralM1955-3 v4

The test switch module consists of a RHGS 6 case with atest switch, RTXP 24, and a two-seat Combiflex terminalbase mounted. An optional DC-switch occupies one seatif selected. A side-by-side mounting kit is included. The

side-by-side mounted units are mounted in a rack orcubicle using the appropriate kit, for example the rackmounting kit.

All connections to the test switch module are made withCombiflex socket leads. Test contacts 1-24 of the testswitch have 20 A Combiflex terminals. The signalcontact of the test switch and the Combiflex terminalbase have 10 A terminals.

For more details about the Combitest system andCombiflex system see section "Related documents".

xx1MRK000371-DA_1.vsd

1

3

4

2

IEC1MRK000371-DA-1 V1 EN-US

Figure 8. Example of a test switch module

1 Test switch

2 DC switch

3 Spare seat, can be used for Key switch

4 RHGS 6 case

Test switchM1952-3 v1

The test switch, RTXP 24, is used to make it possible totest a IED in a failsafe way. Inserting a test-plug handleinto the test switch automatically makes allpreparations for test in the proper sequence. Blockedtrip circuits, shortcircuited CT’s, opened voltage circuitsmakes the IED terminals available for secondaryinjection test.

DC-switchIP633-1 v1M1981-3 v1

The DC-switch is optional in the test switch module andare used to switch the DC-supply of the IED ON/OFF.

M1983-3 v1

The DC-switch is of one seat Combiflex type and needs aCombiflex terminal base to be mounted.



5. Key switch for settingsM1991-3 v2

The key switch for lock-out of settings via the localhuman machine interface is used to prevent unwantedchanges of settings. The switch locks the settings via abinary input.

M1993-3 v1

The key switch is of one seat Combiflex type. To installit, a case including a Combiflex terminal base is needed.One possibility is to install the key switch in the samecase as the test switch.

6. Combiflex modules

Auxiliary relaysSEMOD121105-4 v3

Auxiliary relays can be used together with the IED toprovide functionality such as lock-out, lock-out reset orexternal contact re-enforcement

When the contact rating of the IED is insufficient, it isrecommended to use RXME 1 as a contact re-enforcement. The RXME 1 is then activated from an IEDcontact which is set up to be activated together withthe IED contacts tripping the breaker. The contact of theRXME 1 is connected in parallel, to take over the breakertrip coil current. This gives an efficient solution andmeans no time delay at tripping. See figure 9.

IED

+

TC

+

Breaker

RXME 1

xx06000064-2-en.vsd

-L1L2L3


Figure 9. RXME 1 used as a trip contact re-enforcement

When single pole tripping is used one RXME 1 is requiredper phase and of course per subsystem in redundantsystems.

Lock-out can be arranged with RXMD 1 remanence relayactivated from binary outputs on IED and possible otherprotection relays required to activate lock-out, seefigure 10. The contact of RXMD 1 is connected to openthe closing circuit to the breaker closing coil. Anothercontact can be used to light-up a lamp push button tohave indication of the lock-out and then reset with thepush-button. It is recommended to avoid trip contactlatching as this will mean problem for example with tripcircuit supervision and further at failing breaker, mean

that the trip coil is burnt and the trip coil DC supply istripped. The most important is to prevent that thebreaker is closed at persistent faults.

IED

+

CC

+Breaker

RXMD 1

xx06000231-2-en.vsd

-

+ -

External Close

+


Figure 10. Lock-out using a RXMD 1 relay

For ordering codes see section "Related documents" forreference to more detailed information.

RXME 1 RXMD 1xx06000057.ep


Figure 11. RMXE 1 and RXMD 1 relays

Push button and selector switchSEMOD121142-4 v2

The push button is available with or without pilot lampand with one or two buttons. It is used to reset the lock-out relays when an external independent lock-out andlock-out indications is required. The push button unitcan also be used as a local selector of Auto-Recloseoperation when this is required to be done locally as wellas through communication.

The selector switch is available with two or three fixedpositions and with different contact combinations.Selector switch can e.g. be used as Local/Remoteselector or as a local selector of Auto-Reclose operation.See section "Related documents" for reference to moredetailed information.



xx06000059.eps


Figure 12. Push button and selector switch

Supervision relaySEMOD121154-4 v2

The relay RXEM1 can be used to detect for example lossof DC voltage supply or to detect open circuits. A typicalapplication is continuous supervision of a circuitbreaker trip circuit, including the breaker coil. Seesection "Related documents" for reference to moredetailed information.

xx06000060.eps


Figure 13. Supervision relay RXEM1

7. ConnectorsM2006-3 v3

The connectors are used for analogue signals and binaryin- and output signals.

Use the ferrules to connect two wires to the sameterminal point of a connector of screw compressiontype. Note that 1.5 mm2 is the maximum dimensionallowed on these wires. An appropriate crimping tool isneeded to apply the ferrule to the wires. Use the bridgeconnector to jumper terminal points in a connector.

Use ring-lugs to connect the wires to terminal points ofa connector of ring-lug type. Select ring-lugs suitable towiring dimension and size of fitting screw.

M2026-3 v4

(xx0

1000052.e

ps)


Figure 14. Voltage connector, screw compression type

ANS

I120

0018

7-1-

en.v

sd

ANSI12000187 V1 EN-US

Figure 15. Voltage connector, ring-lug type

xx0100051.vsd

12


Figure 16. Ferrules and bridge connector

1 Ferrules

2 Bridge connector



8. External resistor unit

External resistor unit

SEMOD119678-5 v2

The high impedance resistor unit is used with the highimpedance differential protection. It is available as onephase unit or three phase unit.

IEC03000048-LITEN V1 EN-US

Figure 17. High impedance resistor unit, three phase

xx06000232.eps Dimension

mm [inches]

[18.98]

[18.31][0.33]

[6.9

7]

[4.0

2]

[1.4

8]

[0.79] [7.68]


Figure 18. Dimension drawing of a one phase high impedance resistor unit



en06000234.eps[inches]

[18.98]

[18.31][0.33]

[7.5

0]

[10.4

7]

[7.68][0.79]

[1.5

0]


Figure 19. Dimension drawing of a three phase high impedance resistor unit

WARNING! USE EXTREME CAUTION!

Dangerously high voltages might be present on thisequipment, especially on the plate with resistors. Do any

maintenance ONLY if the primary object protected withthis equipment is de-energized. If required by nationallaw or standard, enclose the plate with resistors with aprotective cover or install in a separate box.

9. External current transformer unit

Summation CT

SEMOD121170-4 v3

The external auxiliary summation current transformersare used for the cost effective summation typedifferential principle.

xx06000061.eps


Figure 20. Summation CT



57 [2

.24]

89 [3

.5]

xx06000233.vsd

482.6 [19]

Dimensionmm [inches]


Figure 21. Dimension drawing of summation current transformers

Distance between the center of the fixing holes is 465 mm[18.33].

WARNING! USE EXTREME CAUTION!

Dangerously high voltages might be present on thisequipment, especially on the plate with resistors. Do any

maintenance ONLY if the primary object protected withthis equipment is de-energized. If required by nationallaw or standard, enclose the plate with transformerswith a protective cover or install in a separate box.

10. Interface converter

Galvanic interface G.703 resp G.703E1M16035-3 v5

The external galvanic data communication converterG.703/G.703E1 makes an optical-to-galvanic conversion

for connection to a multiplexer. These units aredesigned for 64 kbit/s resp 2Mbit/s operation. Theconverter is delivered with 19” rack mountingaccessories.

xx06000245.vsdIEC06000245 V1 EN-US

Figure 22. Galvanic Converter

11. GPS antenna

Introduction

SEMOD55674-5 v4

In order to receive GPS signals from the satellitesorbiting the earth a GPS antenna with applicable cablemust be used.



SEMOD55682-4 v4

The antenna with a console for mounting on a horizontalor vertical flat surface or on an antenna mast. See figure23

A suitable cable is available for ordering.

xx04000155.vsd

1

2

4

3

5

6

7


Figure 23. Antenna with console

where:

1 GPS antenna

2 TNC connector

3 Console, 78x150 mm

4 Mounting holes 5.5 mm

5 Tab for securing of antenna cable

6 Vertical mounting position

7 Horizontal mounting position

SEMOD55693-2 v5

Table 1. GPS – Antenna and cable

Function Value

Max antenna cable attenuation 26 db @ 1.6 GHz

Antenna cable impedance 50 ohm

Lightning protection Must be provided externally

Antenna cable connector SMA in receiver endTNC in antenna end

Accuracy +/-1μs



12. Injection unit REX060

Injection unit REX060GUID-76627CA5-9351-49BB-ABDE-81A939D12BF4 v2

The injection unit REX060 is used to inject voltage andcurrent signals to the generator or motor stator androtor circuits. REX060 generates two square wavesignals with different frequencies for injection into thestator and rotor circuits respectively. The response fromthe injected voltage and currents are then measured bythe REX060 unit and amplified to a level suitable for theanalog voltage inputs of IED.

For local operation, the REX060 unit is provided with acontrol panel on the front.

Local operation shall only be performedaccording to the operation regulationsset up by the relevant operationauthority of the plant.

Mounting the injection unit REX060GUID-264732AC-6C84-44E6-9F86-2065AD0B7D5B v3

The injection unit REX060 case size is 6U, 1/2 x 19”.REX060 can be rack, wall or flush mounted in the sameway as the IED. For guidance, see instructions for rackmounting, wall mounting or flush mounting the IED inthis manual.

REX060 shall be mounted close to the IED. It isrecommended that they are mounted in the samecubicle.

REX060 Front panel

GUID-35437B83-47A9-4E2C-8D22-CCADC51BCC96 v1



Figure 24. REX060 front panel

Rotor injection module RIMGUID-B2CA6C9E-2A24-483C-B9C2-47FFF2BBB283 v2

The RIM module is installed into the REX060 enclosure.The RIM module generates a square wave voltage signalfor injection into the rotor circuit via a capacitor unitREX061 for isolation. The RIM module measures thevoltage and current from the injected signal and the IEDconsecutively calculates the rotor to earth impedance. Ifthe calculated impedance is lower than the preset valuean ALARM and/or TRIP output is set.

Stator injection module SIMGUID-CF2B2004-97E9-4593-95CB-2E86A01EA779 v2

The SIM module is installed into the REX060 enclosure.The SIM module generates a square wave voltage signalfor injection into the stator circuit via the neutral pointVT/NGT. The SIM module measures the voltage andcurrent from the injected signal and the IEDconsecutively calculates the stator to earth impedance.If the calculated impedance is lower than the presetvalue an ALARM and/or TRIP output is set.

13. Coupling capacitor unit REX061

Coupling capacitor unit REX061GUID-39A03C0F-44DC-47DD-9D7E-66C8292CD3A8 v1

REX061 isolates the injection circuit from the rotorexciter voltage.



The REX061 coupling capacitor unit grounding point andgrounding brush of the rotor shaft should be properlyinterconnected.

Coupling capacitor unit REX061GUID-59726B2B-0888-4CC1-8DEA-209F77CA5173 v5

X1 X2


Figure 25. Coupling capacitor unit REX061



217 [8,54]

255

[10]

235

[9,2

5]

84 [3,3] 84 [3,3]Ø 5,5 [0,22]

223

[8,7

8]

2 [0,079]155 [6,1]

199

[7,8

3]38

[1,5

]



Figure 26. Measure and drilling plan

REX061 shall be mounted close to the generator in orderto limit the exposure of the field circuit. Alternatively itcan be located in the excitation cubicle.

The surface of REX061 unit may betemporarily very hot due to heatdissipation, up to about 50° C abovethe ambient temperature. It must beinstalled to get a open air convectionand prevent contact with combustiblematerial to the surface.

14. Shunt resistor unit REX062

Shunt resistor unit REX062

GUID-90D6AF74-D9AC-49B8-B2CA-8A94E58ADEA5 v1

REX062 is typically used when injection is done via agrounding transformer.



Shunt resistor unit REX062GUID-184D9033-33F3-4F85-8847-E9FDC95C3C41 v5

X1


Figure 27. Shunt resistor unit REX062



217 [8,54]

255

[10]

235

[9,2

5]

84 [3,3] 84 [3,3]Ø 5,5 [0,22]

223

[8,7

8]

2 [0,079]155 [6,1]

199

[7,8

3]38

[1,5

]



Figure 28. REX062 measures and drilling plan

REX062 shall be mounted close to the IED. It isrecommended that REX060 and REX062 are mounted inthe same cubicle as the IED.

The surface of REX062 unit may betemporarily very hot due to heatdissipation, up to about 65° C abovethe ambient temperature. It must beinstalled to get a open air convectionand prevent contact with combustiblematerial to the surface.

15. Voltage injection unit RXTTE4

Voltage injection unit RXTTE4GUID-B786414A-A36A-4F3B-B2D5-F1EF9488DA0E v1

The COMBIFLEX voltage injection unit RXTTE4 is usedfor rotor earth fault protection applications. The RXTTE4 contains a voltage transformer with a primary windingfor connection to 120 or 230 V, 50 or 60 Hz supplyvoltage. From the secondary winding of this internal

voltage transformer approximately 40 V AC is injectedvia series capacitors and resistors into the rotor circuit.The injected voltage and current are fed to one voltageinput and one current input on the IED.

In order to mount injection unit RXTTE4 someCOMBIFLEX accessories are required; RX4 terminal base,10A and 20A contact sockets and Crimping tool. See



section "Related documents" for more detailedinformation.

R

C

221 222

421

428

324

325

321

313

314

315

IVT44,7V

ICT1:10

0V

120V 50/60Hz

230V 50/60Hz

RXTTE4



Figure 29. Voltage injection unit RXTTE4 with its main internalcomponents

Rotor earth fault protection can beintegrated in the IED among all otherprotection functions typically requiredfor generator protection. How this isachieved by using COMBIFLEX injectionunit RXTTE4 is described in Instruction1MRG001910.

SEMOD175176-2 v5

Table 2. Rotor earth fault protection based on General current and voltage protection (CVGAPC) and RXTTE4

Function Range or value

For machines with:

• rated field voltage up to 350 V DC

• static exciter with ratedsupply voltage up to

700 V 50/60 Hz

Supply voltage 120 or 230 V 50/60 Hz

Operate earth fault resistancevalue

Approx. 1–20 kΩ

Influence of harmonics in theDC field voltage

Negligible influence of 50 V,150 Hz or 50 V, 300 Hz

Permitted leakage capacitance (1–5) μF

Permitted shaft earthingresistance

Maximum 200 Ω

Protective resistor 220 Ω, 100 W, plate(the height is 160 mm (6,2inches) and width 135 mm (5,31inches))



External resistor for RXTTE4GUID-53080A2D-E836-4827-AD3D-8BD2C1E388D0 v2

The external resistor is used when either there is a needto minimize physical exposure of the field circuit orwhen high harmonic content of the total injectioncurrent can cause overheating of the built-in RXTTE4resistor. The external resistor is delivered mounted onan insulated plate with overall dimensions; (the height is160 mm (6,2 inches) and width 135 mm (5,31 inches)),suitable for wall mounting, see figure 30. It actuallyconsists of two resistors (R1 and R2) which are ondelivery connected in series. It is possible to order twodifferent types of the external resistor. The first type(ordering number RK795102-AD) has exactly the sameohmic value of 220Ω as the internal RXTTE4 resistor. Itshall be used in cases where only physical exposure ofthe field circuit shall be limited. The second type(ordering number RK795102-AB) has different ohmicvalue than internal RXTTE4 resistor. It shall be used ininstallations where current with high harmonic contentis pushed back onto the RXTTE4 injection unit by therotor circuit

1 2 3

X1

R1

R2



Figure 30. External resistor mounted on a plate

16. ESD Field Kit

ESD Field KitGUID-3AEE96A2-E92B-4804-AD52-303B5222848A v1

The ESD Field Kit provides a complete portable ESD safeworkstation when working in the field.


17. Power Supply

Portable Power Supply

GUID-1E38BA0D-C36A-40D6-9BE1-1A6C3C20741C v1

The portable Power Supply provides the IED with power.This can be used at education or demonstration of theIED.

Power CableGUID-6E83F62E-2E84-49D8-83B4-1EDA72047403 v1

For use with the portable Power Supply.

18. Configuration and monitoring tools

PCM600M11607-3 v3

Use PCM600 through all stages of a project, fromengineering, configuring and parameter setting totesting, commissioning, documentation andmaintenance. Use PCM600 to adjust the defaultconfiguration, or to make a new configuration. For moreinformation about PCM600 visitwww.abb.com/substationautomation.

19. Cable and dust cover

Front communicationM1876-3 v2

The front connection cable is used to connect a PC tothe RJ45 port on the local human machine interface. Thecable is a standard crossed-over ethernet cable (RJ45connectors).



http://WWW.ABB.COM/SUBSTATIONAUTOMATION

Dust coverGUID-EAC89866-3EE6-4561-9A77-821E00D9812F v1

The dust cover is used to protect the RJ45 connector onthe local human machine interface.

20.

MicroScada tools

M2080-3 v2

The LIB 520 package provides the following mainfunctions:

• User interface for the interaction with the controlsystem and the controlled process

• Automatic supervision and control• Alarm and event handling• Data acquisition, calculating and reporting

The high voltage software modules are a complement tothe standard MicroSCADA software and provides aneasy-to-build and easy-to-use HMI for supervision andcontrol in MicroSCADA.

The software is made for IEDs, and are providing asimilar user interface as the LIB 500/510 standardlibrary functions.

M2002-3 v3

See http://www.abb.com/substationautomation formore details about the tool, PC requirements etc.

21. User interface

IntroductionGUID-B5F4628D-9A5F-4B5B-9B93-89554BA2337D v2

Local human-machine interface LHMI is not supported inSAM600-IO. However, the user interface functionalitycan be achieved using:• Protection and Control IED Manager PCM600• SAM600-IO LHMI service kit

There is no LHMI in SAM600-IO. TheSAM600-IO LHMI service kit can beused to support commissioning,maintenance, testing andtroubleshooting. References to LHMI inSAM600-IO user documentation shouldbe read as SAM600-IO LHMI service kit.

SAM600-IO LHMI service kitGUID-E29D6926-539D-4BB2-BEBE-C1FF7E919BDC v2

The SAM600-IO LHMI service kit should only be used as atemporary local human-machine interface (LHMI) to helpthe user to trouble shoot a device in field when statusinformation in PCM600 is limited. It can also be used asa support tool during commissioning, maintenance ortesting activities.



Figure 31. SAM600-IO LHMI service kit

The SAM600-IO LHMI service kit contains the samephysical LHMI panel as used in 670/650 series whichincludes the following elements:• Display (LCD)• Keypad• LED indicators• Communication port for PCM600• Serial cable for connection between the SAM600-IO

LHMI service kit and the service port on the device.



22. Ordering

Mounting accessoriesM1823-5 v5

Name For case size Quantity Article number

Protection cover for rear area (release 2.1 and earlier):consisting of a steel cover with a slot for cable entrance at the bottom part, fixingscrews and assembly instruction.

6U x 1/1

RUTAKVADRAT V1 EN-US

1MRK 002 420-AA

Protection cover for rear area (release 2.2 onwards):consisting of a steel cover with a slot for cable entrance at the bottom part, fixingscrews and assembly instruction.

6U x 1/1


1MRK 002 420-RA


6U x 3/4


1MRK 002 420-AB


6U x 3/4


1MRK 002 420-SA


6U x 1/2


1MRK 002 420-AC


6U x 1/2


1MRK 002 420-TA

Protection cover for rear area (all releases):consisting of a steel cover with a slot for cable entrance at the bottom part, fixingscrews and assembly instruction.

6U x 1/4


1MRK 002 420-AE

19” rack mounting kit:consisting of two mounting angles, fixing screws and assembly instruction.

6U x 1/1


1MRK 002 420-CA

6U x 3/4


1MRK 002 420-BA

6U x 1/2


1MRK 002 420-BB

6U x 1/4


1MRK 002 420-BE

Wall mounting kit for 670 and 650 series:consisting of 2 mounting angles, 2 mounting bars, fixing screws and assemblyinstruction.

All sizes 6U


1MRK 002 420-DA

Wall mounting kit for SAM600-IO:consisting of 2 mounting angles, 2 mounting bars, fixing screws and assemblyinstruction.

All sizes 6U


1MRK 002 420–LA

Flush mounting kit (670 and 650 release 2.1 and earlier):consisting of 4 fasteners, sealing strip, fixing screws and assembly instruction.

All sizes


1MRK 000 020-Y

Flush mounting kit (670 and 650 release 2.1 onwards):consisting of 2 fasteners, sealing strip, fixing screws and assembly instruction.

All sizes


1MRK 002 420-PA

Side-by-side mounting kit:consisting of 2 fixing plates, fixing screws and assembly instructions.

All sizes


1MRK 002 420-Z

Note: All kits are complete including screws.



RHGS CasesSEMOD121182-4 v2

RHGS 6 with door, size 6Ux1/4, color RAL 7035 Quantity:

RUTAKVADRATV1 EN-US

1MRK 000 315- AG


RUTAKVADRATV1 EN-US

1MRK 000 315- BH


RUTAKVADRATV1 EN-US

1MRK 000 315- BB

Test switch moduleIP521-1 v1

Selection guideGUID-2378B0A8-B5CC-40F0-8804-586A27BB8C08 v3

Selection of a RTXP24 test switch for each ordered testswitch module is required. See Selection guide for

recommended solutions or applicable IED Product guidefor recommendations. Please refer to section “Relateddocuments”.

Article number

Test switch module RTXP24 Quantity:

RUTAKVADRATV1 EN-US

1MRK 000 371-FA



Product Remark Type of earthing Criteria Article number

RET / REG 670 2-wind / 1CB Internal neutral - RUTA V1 EN-US

RK 926 315-BD

External neutral - Quantity:RUTA V1 EN-US

RK 926 315-BH

2-wind / 2CB Internal neutral 3 phase current groups,2 single phase

RUTA V1 EN-US

RK 926 315-BX

Internal neutral 2 three phase currentgroups, 2 single phase

RUTA V1 EN-US

RK 926 315-BD

External neutral - RUTA V1 EN-US

RK 926 315-BH

3-wind / 1CB Internal neutral 3 phase current groups,2 single phase

RUTA V1 EN-US

RK 926 315-BX

Internal neutral 2 phase current groups,2 single phase

RUTA V1 EN-US

RK 926 315-BD


RK 926 315-BH

3-wind / 2CB Internal neutral - RUTA V1 EN-US

RK 926 315-BD


RK 926 315-BH

RED / REL 670 1CB / 3PhTrip Internal neutral - RUTA V1 EN-US

RK 926 315-AK


RK 926 315-AC

1CB / 1PhTrip Internal neutral - RUTA V1 EN-US

RK 926 315-AK


RK 926 315-AC


RK 926 315-BE


RK 926 315-BV


RK 926 315-BE


RK 926 315-BV

1CB Internal neutral 1 three phase currentgroup

RUTA V1 EN-US

RK 926 315-AF

2CB 2 three phase currentgroups

RUTA V1 EN-US

RK 926 315-AH

2CB Internal neutral 2 three phase currentgroups

RUTA V1 EN-US

RK 926 315-AM


RUTA V1 EN-US

RK 926 315-BN

REC 670 1CB Internal neutral 1 three phase currentgroup

RUTA V1 EN-US

RK 926 315-AK


RUTA V1 EN-US

RK 926 315-BE


RUTA V1 EN-US

RK 926 315-BL

2CB External neutral - RUTA V1 EN-US

RK 926 315-BV


RUTA V1 EN-US

RK 926 315-AF

2CB External neutral 2 three phase currentgroups

RUTA V1 EN-US

RK 926 315-AH



Product Remark Type of earthing Criteria Article number


RUTA V1 EN-US

RK 926 315-AM


RUTA V1 EN-US

RK 926 315-BN

REB 670 Internal neutral 4 three phase currentgroups / 4 bays

RUTA V1 EN-US

RK 926 315-CA

External neutral 1 three phase currentgroup / 1 bay

RUTA V1 EN-US

RK 926 315-AV

RES 670 1 TRM (9I-3U)Single busbarwith 3 bays

Internal neutral 3 three phase currentgroups

RUTA V1 EN-US

RK 926 315–AN

External neutral 1 three phase voltagegroup

RUTA V1 EN-US

RK 926 315–DB

2 TRMs (18I-6U)Double busbarwith 6 bays.

Internal neutral 6 three phase currentgroups

RUTA V1 EN-US

RK 923 315–AN

External neutral 2 three phase voltagegroups

RUTA V1 EN-US

RK 926 315–DB

Note: 2 TRMs (18I-6U) requires two test switches for this application, so two test switch modules 1MRK000371–FA must be used.

1 TRM (6I-6U) Internal neutral 2 three phase currentgroups

RUTA V1 EN-US

RK 926 315–AM


RUTA V1 EN-US

RK 926 315–DC

2 TRM (12I-12U) Internal neutral 4 three phase currentgroups

RUTA V1 EN-US

RK 926 315–AM


RUTA V1 EN-US

RK 926 315–DC

Note: 2 TRMs (12I-12U) requires two test switches for this application, so two test switch modules 1MRK000371–FA must be used.

On/off switch for the DC-supply Quantity: RUTA V1 EN-US

RK 795 017-AA

Labels with symbols for RTXP 24 Quantity:

RUTAKVADRATV1 EN-US

1MRK 000 132-53

M1962-43 v2

Note: Leads with 20 A Combiflex socket on one end and insulation stripped on the other end must be used to connect the test switch tothe terminal. To connect the signal contact of the test switch and the DC switch, leads with 10 A Combiflex socket on one end must beused.

Key switch for settingsSEMOD130356-4 v7

Key switch for lock-out of settings via LHMI Quantity: 1MRK 000 611-A

Note: To connect the key switch, leads with 10 A Combiflex socket on one end must be used.

Combiflex modulesSEMOD124347-4 v2

Auxiliary relays See related documents

Push button and selector switch See related documents

Supervision relay See related documents

Key switch for settings See related documents



ConnectorsM2041-3 v4

Female connector 18 terminals of screw compression type, conductor area max 1 x 2.5mm2 or 2 x 1.0 mm2, 1 pc

Quantity:

RUTAKVADRATV1 EN-US

1MKC 860 001-2

Female connector 18 terminals of spring compression type, conductor area max 1 x 1.5mm2 or 2 x 0.5 mm2, 1 pc

Quantity:

RUTAKVADRATV1 EN-US

1MKC 860 005-2

Ferrule For 2 x 1.5 mm2 conductors in screw compression terminal, 1 pc Quantity:

RUTAKVADRATV1 EN-US

1MKC 840 003-4

Bridge connector For 2 terminals in the current circuit, 1 pc Quantity:

RUTAKVADRATV1 EN-US

1MKC 840 002-1

Bridge connector For 3 terminals, 1 pc Quantity:

RUTAKVADRATV1 EN-US

1MKC 840 002-2

Bridge connector For 4 terminals, 1 pc Quantity:

RUTAKVADRATV1 EN-US

1MKC 840 002-3

Female connector 18 terminals of ring-lug type, 1 pc Quantity:

RUTAKVADRATV1 EN-US

1KHL380110P0001

Female connector 5 terminals of ring-lug type, 1 pc Quantity:

RUTAKVADRATV1 EN-US

1KHL380109P0001

External resistor unitSEMOD120228-4 v8

High impedance resistor unit with resistor and voltage dependent resistor 20-100V,1ph

Quantity:

RK 795 101-MA

High impedance resistor unit with resistor and voltage dependent resistor 20-100V,3ph

Quantity:

RK 795 101-MB

High impedance resistor unit with resistor and voltage dependent resistor100-400V, 1ph

Quantity:

RK 795 101-CB

High impedance resistor unit with resistor and voltage dependent resistor100-400V, 3ph

Quantity:

RK 795 101-DC

External current transformer unitSEMOD123520-4 v5

3 pcs SLCE 8–1 summation transformers on apparatus plate (2U high), 1/1 A Quantity: 1MRK 000 643-EA

3 pcs SLCE 8–1 summation transformers on apparatus plate (2U high), 5/1 A Quantity: 1MRK 000 643-FA

3 pcs SLCE 8–1 summation transformers on apparatus plate (2U high), 2/1 A Quantity: 1MRK 000 643-GA



Interface converter (for remote end data communication)M16668-3 v9

External interface converter from C37.94 to G703 including 1U 19” rack mounting accessories Quantity:

1MRK 002 245-AA

External interface converter from C37.94 to G703.E1 including 1U 19” rack mountingaccessories

Quantity:

1MRK 002 245-BA

GPS antenna and mounting detailsGUID-516667A3-593C-4245-8EAE-198B9DA7F07B v1

GPS antenna, including mounting kits Quantity: 1MRK 001 640-AA

Cable for antenna, 20 m Quantity: 1MRK 001 665-AA

Cable for antenna, 40 m Quantity: 1MRK 001 665-BA



Injection equipmentGUID-3447C871-562C-46B4-A36C-0B8B62D38E48 v7

Rule: If injection equipment is ordered, ROTIPHIZ or STTIPHIZ is required in the IED.

Injection unit, REX060 Quantity: 1MRK 002 500-AA

The REX060 injection unit requires a connection to a VT across the generator neutralpoint earthing resistor. The VT must have a rating of at least 100 VA and a ratedsecondary winding voltage of up to 120 V. It must adhere to IEC 61869-3:2011 section5.5.301 Rated Output Values and the standard values specified according to burdenrange II.

Casing

1/2 x 19" rack casing Basic

Backplane module (BPM) Basic

Human machine interface

HMI and logic module (HLM) Basic

Injection modulesNote: One of RIM and SIM have to be selected if REX060 is specified

Rule: Stator injection module (SIM) is required if 100% stator earth fault protection,injection based (STTIPHIZ) is selected/active in REG670

Stator injection module (SIM) 1MRK 002 544-AA

If the generator is earthed via a primary resistor connected between the generatorneutral point and earth, a VT is placed across the primary resistor. SIM is thenconnected to the secondary side of the VT. The VT must have a rating of at least 100VA and a rated secondary winding voltage of up to 120 V. It must adhere to IEC61869-3:2011 section 5.5.301 Rated Output Values and the standard values specifiedaccording to burden range II.

Rule: Rotor injection module (RIM) is required if Sensitive rotor earth fault protection,injection based (ROTIPHIZ) is selected/active in REG670

Rotor injection module (RIM) 1MRK 002 544-BA

Power supply module

Rule: One Power supply module must be specified

Power supply module (PSM) 24-60 VDC 1MRK 002 239-AB

100-250 VDC 1MRK 002 239-BB

Mounting details with IP40 of protection from the front

19" rack mounting kit 1MRK 002 420-BB

Wall mounting kit for terminal 1MRK 002 420-DA

Flush mounting kit for terminal 1MRK 002 420-PA

Extra IP54 mounting seal + flush mounting kit for terminal 1MRK 002 420-NA

Rule: REX061 requires REX060 and that Rotor injection module (RIM) is selected inREX060 and that Sensitive rotor earth fault protection, injection based (ROTIPHIZ) isselected/active in REG670.

Coupling capacitor unit, REX061 Quantity: 1MRK 002 550-AA

Rule: REX062 requires REX060 and that Stator injection module (SIM) is selected inREX060 and that 100% stator earth fault protection, injection based (STTIPHIZ) isselected/active in REG670.

Shunt resistor unit, REX062 Quantity: 1MRK 002 555-AA



External interface units for Rotor earth fault protectionGUID-A7E65525-260E-4245-85C2-20A26B0DE798 v4

Injection unit for Rotor earth fault protection (RXTTE 4) Quantity:

1MRK 002 108-BA

Protective resistor on plate. R1 = 100 Ώ, R2 = 120 Ώ Quantity:

RK 795 102-AD

Protective resistor on plate. R1 = 560 Ώ, R2 = 560 Ώ Quantity:

RK 795 102-AB

ESD Field kitGUID-701BA355-984F-4FB6-89CB-E64205844596 v1

ESD Field kit Quantity:

1MRK 001 938-A

Portable Power SupplyGUID-8C65E7AF-31EF-4DF7-A9D6-1449C9662640 v2

Power Supply UnitInput voltage: 90-264 V~, 47-63 HzOutput voltage: 48 V DCMax. output current: 2,5 AOutput power: 135 W maxSwitch frequency: 65 kHz

Quantity:

1MRK 001 665-FA

Power Cable2m

Quantity:

1MRK 001 665-EA

Configuration and monitoring toolsIP516-1 v1SEMOD131416-4 v5

PCM600 See related documents

LabelsSEMOD131414-4 v4

LED Label special paper A4, 1 pc Quantity: 1MRK 002 038-CA

LED Label special paper Letter, 1 pc Quantity: 1MRK 002 038-DA

Cable and dust coverGUID-413BF11A-F57C-40E4-89E3-84BFABFF63FD v1

Front connection cable Quantity:

1MRK 001 665-CA

Dust cover LHMI (RJ45) Quantity:

1MKC 890 000-1



MicroScada toolsM2114-3 v2

LIB 520 See related documents

SAM600-IO LHMI service kitGUID-AA273B49-34F4-4F54-8F22-F4A4261785A6 v2

SAM600-IO LHMI service kit Quantity:

1MRK 000 028-SA

23. Related documentsM1827-2 v4

Combiflex, connection and installationcomponents

1MRK 513 003-BEN

Combitest 1MRK 512 001-BEN

Auxiliary, signalling and tripping relays 1MRK 508 015-BEN

Auxiliary relays 1MRK 508 006-BEN

Bistable relays 1MRK 508 017-BEN

Push button and selector switch 1MRK 513 016-BEN

Supervision relay 1MRK 508 024-BEN

LIB 520 1MRK 511 182-BEN

PCM600 1MRS756448 G



ABB ABGrid Automation ProductsSE-721 59 Västerås, SwedenPhone +46 (0) 21 32 50 00

www.abb.com/protection-control

© Copyright 2017 ABB.All rights reserved.

Scan this QR code to visit our website

1MR

K 5

14 0

12-B

EN

670/650 series and sam600-io iec accessories€¦ · x x 0 4 0 0 0 4 5 3 . v s d 1 2 3 4 5 6....

Documents