88 9100 002cpdf.lowes.com/howtoguides/1000227031_how.pdf · front part 1 pc. for each drawer. slide...
TRANSCRIPT
88 9100 002CKitchen CartIMPORTANT NOTE
Carefully remove all the parts from the carton and putthem individually on a soft cloth to prevent scratchesor other damages occuring to the parts.
We have taken great care in the design of thisproduct and request that you carefully and strictlyfollow our assembly instructions to ensure acompleted product as it was designed.
PART LIST
HARDWARE LIST
A.Side Panel
1 pc.
B.Side Panel1 pc.
H.Back Panel
3 pcs.
F.Back Piece2 pcs.
E2.Front Piece1 pc.
E1.Front Piece
1 pc.
I.Back Stretcher1 pc.
J.Front Stretcher1 pc.
K.Front Rail3 pcs.
G.Base1 pc.
R.Shelf2 pcs.
L.Side Rack
1 pc.
M.Side Rack1 pc.
OBrush Chrome Pipes
3 pcs.
D.Middle Panel1 pc.
C.Middle Panel
1 pc.
N.Base Rack1 pc.
(For Drawer U&V packed in separate cartonwith hardware and assembly instructions.)
T.Door1 pc.
S.Door1 pc.
V.KD. Drawer1 pc.
U.KD. Drawer3 pcs.
P.Handle Arm2 pcs.
Q.Round Arm1 pc.
Tools Required For Assembly : Phillips screwdriver
Home Styles Consumer Assistance Line 888-680-7460 and [email protected]
Hex Wrench1 pc.
Machine Screwfor Knob2 pcs.
Wood Screwfor Caster16 pcs. (+2 extra)
Wood Plug10 pcs.(+2 extra)
Castertwo locktwo non-lock4 pcs.
Adjustable Pin8 pcs. (+2 extra)
Head Cap Bolt14 pcs. (+1 extra)
SmallHex Wrench1 pc.
Knob2 pcs.
Assembly Instructions 2/3
STEP 1
STEP 2
STEP 3
G
G
K
K
K
C
D
A
Attach four Castersunderneath Base (G)with Wood Screws.(See ‘Arrow’ stickerindicating front side)
Assemble Front Piece (E1),(E2) and Front Rail (K).(See figure 1)
Attach the assembled unitto Middle Panel (C) and (D).
Attach Side Panel (A) to theside of unit with Head Cap Bolts.
Attach the Back Piece (F), Middle Panel (C)and Back Piece (F), Middle Panel (D) onto theBase (G).
IMPORTANTDo not tighten up all the screws until each part is properly assembled.You should keep Hex Wrench in the safe place as you may need totighten up the Head Cap Bolts in the future.
FF
C D
E1
E2
Wood Screw
Wood Screw
Head Cap Bolt
Locking Caster(On Front)
(Figure 1)
R
R
STEP 4
STEP 7
STEP 8
J
B
I
Insert Adjustable Pins into bothside panels and middle panelsat the desired level.Place Shelf (R).
HH H
A
M
N
O
L STEP 5Attach Side Rack (L) to Side Panel (A) withHead Cap Bolts.
Attach Brush Chrome Pipes (O) and Base Rack (N)to the Side Rack (L).
Attach Side Rack (M) to the Side Panel (A),using Head Cap Bolts.
Head Cap Bolt
Head Cap Bolt
Adjustable Pin
Head Cap Bolt
BQ
P
PSTEP 6Attach Handle Arm (P) to Side Panel (B)with Head Cap Bolts.
Slide the Round Arm (Q) into place.
Cover up all holeswith Wood Plugs.
Slide Back Panel (H) into place.
Attach Back and FrontStretcher (I), (J) to the unitwith Head Cap Bolts.
Attach Side Panel (B) to the otherside of unit with Head Cap Bolts.
Assembly Instructions 3/3
88 9100 002C
Drawer (U)
Assembly Instructions
U3.Side Part1 pc. for eachdrawer.
U4.Side Part
1 pc. for eachdrawer.
U5.Base Part1 pc. for eachdrawer.
U2.Back Part1 pc. for eachdrawer.
U2
U5
U5
U4
U4
U3
U3
U1
U1
Assemble the Pull Handlewith Machine Screw onthe Front Part (U1).(See the figure 4)
(Figure 2)
(Figure 3)
HARDWARE LIST
Pull Handle3 pcs.
Machine Screwfor Pull Handle
6 pcs.
Wood Screw (short)for base part18 pcs.(+1 extra)
Wood Screw (long)for side part24 pcs.(+1 extra)
Insert the remaining (6) 1/2 screws�
into the pre-drilled holes on Base Part(U5), then tighten all screws.(See the figure 3)
* If you are missing any of theseparts, please contact our DMICustomer Service Departmentat 1-877-831-0319 or fax us at1-800-755-2878.
U1.Front Part1 pc. for eachdrawer.
Slide the Plywood Base Part (U5) intothe grooves on Side Parts (U3) and (U4).Be sure to push the plywood all the wayforward so it meets the Front Part (U1).(See the figure 2)
Unfinished Side
U2
U3
U4
U1
(Figure 1)
make sure rolleris on the back
UNIT PART LIST
Using a ,philips screwdriverinsert 1” screws into the pre-drilledholes as shown, tighten half way.(See the figure 1)
U1
(Figure 4)
V1
88 9100 002C
Drawer (V)
V3.Side Part
1 pc. .
V5.Base Part1 pc.
V2.Back Part1 pc. .
V2
V2
V5
V5
V3
V4
V4
V4
V3
V3
V1
V1
V1
Assemble the Pull Handlewith Machine Screw onthe Front Part (V1).(See the figure 4)
(Figure 1)
(Figure 2)
(Figure 3)
(Figure 4)
HARDWARE LIST
Pull Handle1 pcs.
Machine Screwfor Pull Handle
2 pcs.
Wood Screw (short)for base part6 pcs.(+1 extra)
Wood Screw (long)for side part8 pcs.(+1 extra)
Insert the remaining (6) 1/2 screws�
into the pre-drilled holes on Base Part(V5), then tighten all screws(See the figure 3)
make sure rolleris on the back
* If you are missing any of these parts,please contact our DMI CustomerService Department at 1-877-831-0319or fax us at 1-800-755-2878.
V1.Front Part1 pc.
Slide the Plywood Base Part (V5) intothe grooves on Side Parts (V3) and (V4).Be sure to push the plywood all the wayforward so it meets the Front Part (V1).(See the figure 2)
Unfinished Side
V4.Side Part1 pc.
UNIT PART LIST
Using a ,philips screwdriverinsert 1” screws into the pre-drilledholes as shown, tighten half way.(See the figure 1)
Assembly Instructions