99-7403 · 2007-06-21 · 99-7403 4 1 1 disconnect the negative battery terminal to prevent an...
TRANSCRIPT
1-800-221-0932 • www.metraonline.comCOPYRIGHT© 2003-07 METRAELECTRONICS CORPORATION
2003- 04 Nissan Pathfinder (LE Only)
VEHICLE APPLICATIONS
KIT FEATURES
DIN head unit provisions with pocket
ISO head unit provisions with pocket
99-7403
QUESTIONS?Call the Help Line: (800)253 TECH
Monday - Friday 9:00 am - 7:00 pm ESTSaturday - Sunday 10:00 am - 4:00 pm EST
INST997403
KIT COMPONENTS
Phillips screwdriverSmall Flat Blade Screwdriver
ISO Snap In Brackets
TOOLS REQUIRED
Radio Housing
Trimplate
2001- 03 Infiniti QX4
Rev. 06-21-07
• DASH DISASSEMBLY- 2003-04 Nissan Pathfinder (LE Only) . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . 1
• KIT ASSEMBLY- DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2- ISO DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
• FINAL ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
99-7403 NOTES
- 2001-03 Infiniti QX4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
99-7403
14
1 Disconnect the negative batteryterminal to prevent anaccidental short circuit.
2 Using a small flat blade screwdrivergently pry out on the top of the a/cvent assembly (including clock) andremove. (Figure A).
3 Remove (2) Phillips screws from thetop of the radio trim panel andunclip and remove panel.(Figure B).
4 Remove (4) Phillips screws from theradio to remove.
2003-04 NISSAN PATHFINDER (LE Only)
Wiring and Re-connection Assembly1 Locate the factory wiring harness in
the dash. Metra recommends usingthe proper mating adapter andmaking the connections as shown.(Isolate and individually tape off theends of any unused wires to preventelectrical short circuit. See Figure A)
2 Re-connect the negative batteryterminal and test the unit for properoperation.
3 Reassemble in reverse order ofdisassembly.
Wiring and Re-connection Assembly
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
99-7403
Figure A
Figure A
Figure B
2001-03 INFINITI QX4
99-7403
32
99-7403
1 Slide the DIN cage into the RadioHousing and secure by bending themetal locking tabs down.(Figure A.)
2 Slide the aftermarket head unit intothe cage and secure.
DIN Head Unit Provision
1 Mount the ISO Brackets to the headunit with the screws supplied withthe unit. (Figure A.)
2 Slide the head unit into the radioopening until the side clips engage.(Figure B.)
3 Snap the Trimplate into the RadioHousing.
Figure A
Figure B
ISO DIN Head Unit Provision
Figure A