abaco working table (awt7523c)

ABACO WORKING TABLE(AWT7523C)

OPERATION MANUAL

ABACO MACHINES

ABACO MACHINES (USA)

14508 S. Garfield Ave., Paramount, CA 90723, USATel : 310-532-0366 Fax : 310-532-0499

Email : [email protected] : www.abacomachines.com

APPLICABLE MODELof this WORKING TABLE:

AWT7523C

OPERATION MANUAL

ABACO MACHINES

AWT7523C - Operation Manual ABACO MACHINES -All Rights Reserved

INDEX

Item Pages

I Equipment General Information................................... 1

II Technical Specifications ............................................. 1

1) Dimensions ............................................................. 1

.........................................................2) Spare Part List 2

III Safety Instructions........................................................ 4

1) General Warnings, Cautions and Notes..................... 4

2) Device usage ........................................................... 5

IV Appendix ..................................................................... 7

V Technical Problems & Solutions.................................. 8

VI Inspection & Maintenance .......................................... 8

VII Warranty Policy............................................................ 9

Warranty Certificate .................................................... 10

General Safety Operation Manual Instructions Summary:

It is essential to carefully review and understood this Operation Manual before operating the equipment. Failing to read and understand this entire manual may cause injury or death to personnel, or damage to equipment and the products that are being handled by this equipment if not properly followed. This safety summary includes general safety precautions and instructions that must be understood and applied before, during, and after operations, as well as maintenance to ensure personnel safety and protection of equipment. Prior to performing any task, the contents included in this manual should be reviewed and fully understood.

This manual highlights essential operating or maintenance procedure, practice, condition, statement, etc. that if not strictly observed, could result in injury, or death of, personnel or long term hazards; could result in damage to products being handled, or damage to/destruction of equipment.


Length (A)inches (mm)

Width (B)inches (mm)

Height (C)inches (mm)

*W.L.L. lbs (kg)

75 ⁷⁄₈ (1927) 23 ¹⁵⁄₁₆ (608)37 ¹⁵⁄₁₆ - 40 ⁹⁄₁₆(965 - 1030)

4824 (2200)

Net Weightlbs (kg)

169.4 (77)

- Working Table (AWT7523C) is used to put the stone slab for grinding, polishing and drilling.

- Linking hooks are designed to create multi-way table layout arrangements by combination of single tables. (Refer to page 7.)

- Rubber-lined table protects stone slabs from scratches or damages.

- The design is convenient and efficient, can be assembled to suit the shape and size of the stone slab.

- With the design of each detachable part should be easy to disassemble, convenient for moving and repacking.

- It has a high level adjustment at the bottom of the table, helping to adjust the surface of stone slab to be even.

- AWT7523C is made of square, rectangular steel tubes.

- In addition, it has four swivel casters for being easy to move the table in any position.

I. EQUIPMENT GENERAL INFORMATION:

II. TECHNICAL SPECIFICATIONS:

1) Dimensions:

* W.L.L: Work Load Limit

1AWT7523C - Operation Manual ABACO MACHINES -All Rights Reserved

3

02

08

12

22

01

04

04

07

01

20

01

04

04

08

04

CODE DESCRIPTION QTY.

AWT7523C-01

AWT7523C-02

AWT7523C-03

AWT7523C-04

AWT7523C-05

AWT7523C-06

AWT7523C-07

AWT7523C-08

AWT7523C-09

AWT7523C-10

AWT7523C-11

AWT7523C-12

AWT7523C-13

AWT7523C-14

AWT7523C-15

Middle Support

SPARE PARTS LIST

01AWT7523C-16

AWT7523C-17

AWT7523C-18

AWT7523C-19

AWT7523C-20

02

40

04

04

AWT7523C-21Bolt M10x20 16

AWT7523C-22 16

AWT7523C-23Washer Ø10xØ20x2 16

Spring washer Ø10

POS.

Swivel caster

Rubber pad 2

Washer Ø10xØ20x1.5

Rubber pad 1

Right Frame

Circlip Ø12

Washer Ø12

Pusher, aluminum

Thread Shaft

Bottom Frame

Nut M10

Top Frame

Lock Nut M12

Height adjust handle

Locking Nut

Left Frame

Screw M4x15

Bolt M10x120

Bolt M10x70

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23


2) Spare part list:

2

Center Support Bar(sold separately) can be attached if required.


4

III. SAFETY INSTRUCTIONS:

1) General Warnings, Cautions and Notes:

a. Before operations:

Before operation make sure the following:

- All nuts and bolts are tightened securely.

- All four swivel casters are locked safely.

- The Working Table is placed on a flat and smooth surface, not on a wavy or rough surface.

- The Working Table is in good operating condition.

- The rubber pad are clean, no dust, oil or debris on it.

- Confirm all the welded joints are free from any defects or damage, such as separation, crack, and so forth.

- Use appropriate PPE (Personal Protective Equipment) to protect against injury.

b. During operations:

- Make sure the weight of the slabs being placed is within the specified W.L.L (Refer to the table at page 1).

- Follow the steps and instructions in this operation manual.

- For safety purposes, you (the operator) are responsible for following all applicable laws and regulations in your region.

c. After operations:

- Clean the Working Table thoroughly after each use.

- Store in a well-ventilated place, avoid places with high heat or humidity.

Note: See Maintenance Instructions section in this manual for more details.


2) Device usage:

Step 1: Lock four swivel casters (Figure 1.1).

Figure 1.1

Step 2: Place the stone slab on the table (Figure 2.1).

5

Stone slab

Figure 2.1


Before After

6

Stone slab

Figure 2.2

Locking nut

Height adjuster handle

Note: To adjust the stone slab surface even, loosen the locking nut and rotate the handle clockwise (Figure 2.2).height adjuster


IV. APPENDIX:

Various ways to layout/display the Working Table.

Linking hook


8

V. TECHNICAL PROBLEMS & SOLUTIONS:

VI. INSPECTION & MAINTENANCE:

- Operator is responsible to check the equipment regularly, not

limited to check the welded parts without any defects or cracking,

etc. to ensure the equipment is in good operating conditions.

- Periodically, operator is responsible to schedule equipment

maintenance, especially for check and tighten the nuts and bolts.

- Always keep the equipment clean and away from grease or any

foreign substance as they may cling onto the table and prevent it

from scratching or operating improperly.

- Operator is recommended to always keep necessary spare parts on

hand for immediate maintenance or repair purposes before

operating.

- Operator is responsible to ensure all parts are genuine parts from

the manufacturer, and they are designed specifically for to be

installed to this equipment.

- Operator is responsible to ensure all repair installation are

performing appropriately and in safety manner.

- Store this equipment in a well-ventilated place (dry and cool),

avoid places with high heat and/or humidity.

- Keep maintenance records to ensure safety checks are carried out.


Threaded shaft

The swivel casters are hard to move.

Dust and/or rust.

Clean, lubricate and/or replace with a new one.

Height adjuster handle is hard to turn.

Dust, rust, and/or damage of the threaded shaft.

Clean, lubricate and/or replace with a new one.

Technical problem

Cause Solution Image

9

VII. WARRANTY POLICY:

At the time of delivery, it is necessary to inspect the Abaco Working Table (AWT7532C) to make sure that it has not been damaged during shipment. The product at the time of dispatch is warranted to be free of defects in material or workmanship.

Claims for errors, shortages, defects, or nonconformities

ascertainable upon inspection must be made in writing within eight

business days from the date of product delivery. Claims not made as

provided above and within the applicable time period will be barred

and no other claims will be considered.

We provide a warranty on the one (1) year Abaco Working Table

(AWT7532C) from the date of purchase.

During warranty period, we will provide the replacement parts at

no charge (Please note: shipping and handling fees may apply).

Warranty coverage is void if:

- The operator failed to comply with the instructions in the

manual.

- The specifications are not followed.

- Damage is due to inadequate maintenance and inspections.

- Damage is due to improper storage and/or usage.

- Modification and repairs made to the equipment were performed

by the user/operator without the manufacture's knowledge and

agreement.

- Aftermarket or none genuine spare parts were used for repair

installation.

- Modification and repair installations were conducted by

uncertified individual.


10

WARRANTY CERTIFICATE

You are kindly requested to read the following carefully.

PERIOD

The warranty starts from the date of purchase (date on distributors invoice).

Warranty is valid for a period of twelve (12) months.

WARRANTY

This warranty is limited only to provide replacements of the parts recognized by the Company as defective (excluding worn-outs and consumables.)

The Company is not responsible for any misuse or abuse of the product after purchase and/or caused by negligence from the content of this manual.

In an event the equipment failed to operate and/or required technical support, operator/user is responsible for reaching out to our Customer Support Department. One of our team member will inform you (operator/user) of the appropriate procedures on how to file warranty claim and advise you to your nearest approved service center.

EXCLUSIONS

Warranty does not apply for damages or failures caused by:

Misuses, errors in transportation, incorrect handling or failing to maintain the equipment appropriately.

Use of non-genuine parts/accessories, or of incorrect specs.


THIS MANUAL SHALL BE REVISED WITHOUT PRIOR NOTICE

FOR IMPROVEMENT PURPOSES

DO NOT COPY AND/OR QUOTE THE CONTENTS WITHOUT

PRIOR WRITTEN CONSENT OF ABACO MACHINES USA, Inc.

All Rights Reserved:

Abaco Machines USA, Inc.

E19

abaco working table (awt7523c)

Documents