access motor co., ltd.%e7%a...mass of the vehicle (with bodywork) in running order: 374±5 kg 12.2....
TRANSCRIPT
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
APPLICATION FOR EXTENSION APPROVAL OF TWO OR THREE-WHEEL MOTOR VEHICLES
ACCORDING TO 2002/24/EC DIRECTIVE AMENDED BY 1137/2008/EC
1. Trade name or mark of the vehicle : Access
2. Type of the vehicle : AX700-UL
3. Manufacturer’s name and address : Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan
4. If applicable, name and address of manufacturer’s representative
: Not applicable
5. Brief description : Quadricycle
6. Submitted for approval on (date) : May 25, 2015
We herewith certify that we didn’t apply nor receive a certificate for the above mentioned type in any other EC/ECE member state.
Name: Sean Huang Position: General Manager Date: May 25, 2015
THIS APPLICATION IS ACCOMPANIED WITH:
-The test report
Access Motor Co., Ltd. No 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
CERTIFICATE OF CONFORMITY CERTIFICATE OF CONFORMITY ACCOMPANYING EACH VEHICLE IN THE SERIES OF THE TYPE
WHICH HAS BEEN APPROVED
The undersigned:
_______________ hereby certifies that the following vehicle:
0.1. Make: Access
0.2. Type: AX700-UL
Variant: AX600-UL
Version: AMX600-UL
0.2.1. Commercial name(s): Access Motor, as option: SS250R, Hammel, Quadzilla,
Bogart Patriot, Nexmotor, Tomahawk, Apollo, Spike, Speed,
Maverick, TKM, FOCUS, TENA, TRITON, MAX, APACHE,
Burelli, Warrior
0.4. Vehicle category: L7e
0.4.1. Vehicle category according to Directive 97/24/EC, Chapter 7: N.A.
0.5. Name and address of the manufacturer:
Access Motor Co., Ltd.
No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan
0.6. Location of the statutory plate: R, x1120, y128, z710
Vehicle identification number: RK3AX3C235A000001
0.7. Location of the vehicle identification number on the chassis:
R, x60, y90, z320
Conforms in all respects to the type described in EC type-approval
- EC type-approval number: e4*2002/24*3058*04
- Dated:
The vehicle can be permanently registered without requiring any further approvals, for driving on the right/left
and for using metric/imperial units for the speedometer.
Chia-Yi, Taiwan, R.O.C.
(Place) (Date)
(Signature) (Position)
Additional Information
1. Number of axles: 2 and wheels: 4
3. Wheel base: 1440 mm
6.1. Length: 2390±10 mm
7.1. Width: 1200±10 mm
8. Height: 1520±10 mm
12.1. Mass of the vehicle (with bodywork) in running order: 374±5 kg
12.2. Unladen mass of the vehicle: 360±5 kg
14.1. Technically permissible maximum laden mass: 554±5 kg
14.2. Distribution of this mass among the axles:
1. 255 kg 2. 299 kg
14.3. Technically permissible mass on each axle:
1. 255 kg 2. 299 kg
17. Maximum mass of trailer:
(braked): 174 kg (unbraked): ..............kg
19.1. Maximum vertical load at the coupling point for a trailer: 35 kg
20. Engine manufacturer: Access Motor Co., Ltd.
21. Engine type as marked on the engine: E23
21.2. Engine number: E23R??????
22. Working principle: electric/spark ignition/compression ignition, four/two stroke
23. Number and arrangement of cylinders: S
24. Cylinder capacity: 608 cm3
25. Fuel: P
26. Maximum net power or maximum continuous rated power as applicable:
12.44 kW at 4200 min-1
26.1. Ratio: maximum net power or maximum continuous rated power/mass of the vehicle in running order: 0.033 kW/kg
28. Gearbox (type): A
29. Gear ratio:
Forward H position : R. MIN: 1: 15.104 R. MAX: 1: 7.169
L position : R. MIN: 1: 25.489 R. MAX: 1: 12.097
Backward: 1: 26.307
32. Tyre size designation:
Axle 1: AT25×8-12 or AT26×8-14 Axle 2: AT25×10-12 or AT26×10-14
37. Body: No
41. Number and configuration of doors: N.A.
42.1. Number and position of seats: 2, r1: 1C, r2: 1C
43.1. Approval mark of coupling device, if fitted: e4*97/24*97/24/10*3026*00
44. Maximum speed: 60 km/h
45. Sound level:
In accordance with 97/24/EC Chapter 9, amendment 2009/108/EC
Stationary: 83 dB(A) at engine speed: 3150 min-1
Drive-by: 80 dB(A)
46. Exhaust emissions:
In accordance with 97/24/EC Chapter 5, amendment 2013/60/EU
46.1 Euro level: 2
46.2 Type I test: CO: 0.696 g/km, HC: 0.071 g/km, NOx: 0.124 g/km, HC+NOx: --
46.3 Type II test: for motorcycles and tricycles: CO: 0.001 %vol
Visible air pollution caused by an engine with compression ignition: N.A.
- corrected value of absorption coefficient: N.A.
47. Fiscal power or national code number(s):
Italy: France: Spain:
Belgium: Germany: Luxembourg:
Denmark: Netherlands: Greece:
United Kingdom: Irland: Portugal:
Austria: Sweden: Finland:
Czech Republic: Estonia: Cyprus:
Latvia: Lithuania: Hungary:
Malta: Poland: Slovenia:
Slovakia: Romania: Bulgaria:
Croatia:
50. Remarks:
51. Exemptions:
Access Motor Co., Ltd. No 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
CERTIFICATE OF CONFORMITY CERTIFICATE OF CONFORMITY ACCOMPANYING EACH VEHICLE IN THE SERIES OF THE TYPE
WHICH HAS BEEN APPROVED
The undersigned:
_______________ hereby certifies that the following vehicle:
0.1. Make: Access
0.2. Type: AX700-UL
Variant: AX700-UL
Version: AMX700-UL
0.2.1. Commercial name(s): Access Motor, as option: SS250R, Hammel, Quadzilla,
Bogart Patriot, Nexmotor, Tomahawk, Apollo, Spike, Speed,
Maverick, TKM, FOCUS, TENA, TRITON, MAX, APACHE,
Burelli, Warrior
0.4. Vehicle category: L7e
0.4.1. Vehicle category according to Directive 97/24/EC, Chapter 7: N.A.
0.5. Name and address of the manufacturer:
Access Motor Co., Ltd.
No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan
0.6. Location of the statutory plate: R, x1120, y128, z710
Vehicle identification number: RK3AX3X205A000001
0.7. Location of the vehicle identification number on the chassis:
R, x60, y90, z320
Conforms in all respects to the type described in EC type-approval
- EC type-approval number: e4*2002/24*3058*04
- Dated:
The vehicle can be permanently registered without requiring any further approvals, for driving on the right/left
and for using metric/imperial units for the speedometer.
Chia-Yi, Taiwan, R.O.C.
(Place) (Date)
(Signature) (Position)
Additional Information
1. Number of axles: 2 and wheels: 4
3. Wheel base: 1440 mm
6.1. Length: 2390±10 mm
7.1. Width: 1200±10 mm
8. Height: 1520±10 mm
12.1. Mass of the vehicle (with bodywork) in running order: 374±5 kg
12.2. Unladen mass of the vehicle: 360±5 kg
14.1. Technically permissible maximum laden mass: 554±5 kg
14.2. Distribution of this mass among the axles:
1. 255 kg 2. 299 kg
14.3. Technically permissible mass on each axle:
1. 255 kg 2. 299 kg
17. Maximum mass of trailer:
(braked): 174 kg (unbraked): ..............kg
19.1. Maximum vertical load at the coupling point for a trailer: 35 kg
20. Engine manufacturer: Access Motor Co., Ltd.
21. Engine type as marked on the engine: E20
21.2. Engine number: E20R??????
22. Working principle: electric/spark ignition/compression ignition, four/two stroke
23. Number and arrangement of cylinders: S
24. Cylinder capacity: 686 cm3
25. Fuel: P
26. Maximum net power or maximum continuous rated power as applicable:
10.80 kW at 4400 min-1
26.1. Ratio: maximum net power or maximum continuous rated power/mass of the vehicle in running order: 0.029 kW/kg
28. Gearbox (type): A
29. Gear ratio:
Forward H position : R. MIN: 1: 15.104 R. MAX: 1: 7.169
L position : R. MIN: 1: 25.489 R. MAX: 1: 12.097
Backward: 1: 26.307
32. Tyre size designation:
Axle 1: AT25×8-12 or AT26×8-14 Axle 2: AT25×10-12 or AT26×10-14
37. Body: No
41. Number and configuration of doors: N.A.
42.1. Number and position of seats: 2, r1: 1C, r2: 1C
43.1. Approval mark of coupling device, if fitted: e4*97/24*97/24/10*3026*00
44. Maximum speed: 60 km/h
45. Sound level:
In accordance with 97/24/EC Chapter 9, amendment 2009/108/EC
Stationary: 85 dB(A) at engine speed: 3300 min-1
Drive-by: 80 dB(A)
46. Exhaust emissions:
In accordance with 97/24/EC Chapter 5, amendment 2009/108/EC
46.1 Euro level: 2
46.2 Type I test: CO: 0.805 g/km, HC: 0.049 g/km, NOx: 0.101 g/km, HC+NOx: --
46.3 Type II test: for motorcycles and tricycles: CO: 1.11 %vol
Visible air pollution caused by an engine with compression ignition: N.A.
- corrected value of absorption coefficient: N.A.
47. Fiscal power or national code number(s):
Italy: France: Spain:
Belgium: Germany: Luxembourg:
Denmark: Netherlands: Greece:
United Kingdom: Irland: Portugal:
Austria: Sweden: Finland:
Czech Republic: Estonia: Cyprus:
Latvia: Lithuania: Hungary:
Malta: Poland: Slovenia:
Slovakia: Romania: Bulgaria:
Croatia:
50. Remarks:
51. Exemptions:
Access Motor Co., Ltd. No 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
CERTIFICATE OF CONFORMITY CERTIFICATE OF CONFORMITY ACCOMPANYING EACH VEHICLE IN THE SERIES OF THE TYPE
WHICH HAS BEEN APPROVED
The undersigned:
_______________ hereby certifies that the following vehicle:
0.1. Make: Access
0.2. Type: AX700-UL
Variant: AX800-UL
Version: AMX800-UL
0.2.1. Commercial name(s): Access Motor, as option: SS250R, Hammel, Quadzilla,
Bogart Patriot, Nexmotor, Tomahawk, Apollo, Spike, Speed,
Maverick, TKM, FOCUS, TENA, TRITON, MAX, APACHE,
Burelli, Warrior
0.4. Vehicle category: L7e
0.4.1. Vehicle category according to Directive 97/24/EC, Chapter 7: N.A.
0.5. Name and address of the manufacturer:
Access Motor Co., Ltd.
No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan
0.6. Location of the statutory plate: R, x1120, y128, z710
Vehicle identification number: RK3AX3L245A000001
0.7. Location of the vehicle identification number on the chassis:
R, x60, y90, z320
Conforms in all respects to the type described in EC type-approval
- EC type-approval number: e4*2002/24*3058*04
- Dated:
The vehicle can be permanently registered without requiring any further approvals, for driving on the right/left
and for using metric/imperial units for the speedometer.
Chia-Yi, Taiwan, R.O.C.
(Place) (Date)
(Signature) (Position)
Additional Information
1. Number of axles: 2 and wheels: 4
3. Wheel base: 1440 mm
6.1. Length: 2390±10 mm
7.1. Width: 1200±10 mm
8. Height: 1520±10 mm
12.1. Mass of the vehicle (with bodywork) in running order: 374±5 kg
12.2. Unladen mass of the vehicle: 360±5 kg
14.1. Technically permissible maximum laden mass: 554±5 kg
14.2. Distribution of this mass among the axles:
1. 255 kg 2. 299 kg
14.3. Technically permissible mass on each axle:
1. 255 kg 2. 299 kg
17. Maximum mass of trailer:
(braked): 174 kg (unbraked): ..............kg
19.1. Maximum vertical load at the coupling point for a trailer: 35 kg
20. Engine manufacturer: Access Motor Co., Ltd.
21. Engine type as marked on the engine: E24
21.2. Engine number: E24R??????
22. Working principle: electric/spark ignition/compression ignition, four/two stroke
23. Number and arrangement of cylinders: S
24. Cylinder capacity: 781 cm3
25. Fuel: P
26. Maximum net power or maximum continuous rated power as applicable:
14.65 kW at 5000 min-1
26.1. Ratio: maximum net power or maximum continuous rated power/mass of the vehicle in running order: 0.039 kW/kg
28. Gearbox (type): A
29. Gear ratio:
Forward H position : R. MIN: 1: 15.104 R. MAX: 1: 7.169
L position : R. MIN: 1: 25.489 R. MAX: 1: 12.097
Backward: 1: 26.307
32. Tyre size designation:
Axle 1: AT25×8-12 or AT26×8-14 Axle 2: AT25×10-12 or AT26×10-14
37. Body: No
41. Number and configuration of doors: N.A.
42.1. Number and position of seats: 2, r1: 1C, r2: 1C
43.1. Approval mark of coupling device, if fitted: e4*97/24*97/24/10*3026*00
44. Maximum speed: 60 km/h
45. Sound level:
In accordance with 97/24/EC Chapter 9, amendment 2009/108/EC
Stationary: 88 dB(A) at engine speed: 3750 min-1
Drive-by: 80 dB(A)
46. Exhaust emissions:
In accordance with 97/24/EC Chapter 5, amendment 2013/60/EU
46.1 Euro level: 2
46.2 Type I test: CO: 0.574 g/km, HC: 0.027 g/km, NOx: 0.055 g/km, HC+NOx: --
46.3 Type II test: for motorcycles and tricycles: CO: 0.015 %vol
Visible air pollution caused by an engine with compression ignition: N.A.
- corrected value of absorption coefficient: N.A.
47. Fiscal power or national code number(s):
Italy: France: Spain:
Belgium: Germany: Luxembourg:
Denmark: Netherlands: Greece:
United Kingdom: Irland: Portugal:
Austria: Sweden: Finland:
Czech Republic: Estonia: Cyprus:
Latvia: Lithuania: Hungary:
Malta: Poland: Slovenia:
Slovakia: Romania: Bulgaria:
Croatia:
50. Remarks:
51. Exemptions:
Vehicle Technology Division
P.O. Box 777 Tel. + 31 (0)79 345 83 02 Vehicle Admission & Surveillance
2700 AT Zoetermeer E-mail [email protected] The Netherlands www.rdw.nl
WVTA 2002.24-2013.60 v6.01 Page 1 of 4
THE NETHERLANDS (N E D E R L A N D)
EC TYPE-APPROVAL CERTIFICATE
Communication concerning:
- type-approval (1)
- extension of type-approval (1)
- refusal of type-approval (1)
- withdrawal of type-approval (1)
of a type of vehicle with regard to Directive 2002/24/EC.
EC type-approval number : e4*2002/24*3058*04
Reason for extension : Addition of version AMX700-UL, AMX600-UL
and AMX800-UL with new front exterior parts
including front lamp and 14” tyres
0. General
0.1. Make(s) (trade name of the
manufacturer)
: Access
0.2. Type : AX700-UL
0.2.1. Commercial name(s) : Access Motor, as option: SS250R, Hammel,
Quadzilla, Bogart Patriot, Nexmotor, Tomahawk,
Apollo, Spike, Speed, Maverick, TKM, FOCUS,
TENA, TRITON, MAX, APACHE, Burelli,
Warrior, GOES
0.3. Means of identification of type, if
marked on the vehicle
: ???AX3???????????
0.3.1. Location of that marking : On the right side of frame body
0.4. Category (2)
: L7e
0.5. Name and address of the vehicle
manufacturer
: ACCESS MOTOR CO., LTD.
No. 5, Chung-Hsin Rd., Chia-Tai Industrial
Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan
Type-approval number: e4*2002/24*3058*04
WVTA 2002.24-2013.60 v6.01 Page 2 of 4
0.5.1. Name(s) and address(es) of assembly
plant(s)
: ACCESS MOTOR CO., LTD.
No. 5, Chung-Hsin Rd., Chia-Tai Industrial
Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan
The undersigned hereby certifies the accuracy of the manufacturer’s description in the attached
information document of the vehicle type described above, for which one or several representative
samples, selected by the competent approval authorities, has (have) been submitted as prototype(s) of
the vehicle type and that the attached test results are applicable to the vehicle type.
The vehicle type meets/does not meet
(1) the technical requirements of all relevant separate Directives
(as last amended) listed in the table of Annex I to Directive 2002/24/EC.
The approval is granted/refused/withdrawn (1)
.
Place : Zoetermeer
Signature :
Date :
Attachments: –
–
–
–
Information document, Parts 1 and 2 (Annex II).
Test results (Annex VII).
Name(s) and specimen(s) of the signature of the persons authorised to sign the
certificates of conformity and a statement of their position in the company.
A model certificate of conformity.
___________________________
(1) Delete where not applicable. (2) According to the classification introduced in Article 1.
Type-approval number: e4*2002/24*3058*04
WVTA 2002.24-2013.60 v6.01 Page 3 of 4
ANNEX VII
TEST RESULTS
(Article 5(1), first subparagraph)
In each case, the information must make clear to which variant and version it is applicable.
One version may not have more than one result.
1. Results of the sound level tests.
Number of the base Directive and latest amending Directive applicable to the approval.
In the case of a Directive with two or more implementation stages, indicate also the
implementation stage:
- 97/24/EC Chapter 9 as last amended by 2009/108/EC
Variant/version AX700-UL/
AX700-UL,
AMX700-UL
AX600-UL/
AX600-UL,
AMX600-UL
AX800-UL/
AX800-UL,
AMX800-UL
Moving dB(A) 80 80 80
Stationary dB(A) 85 83 88
at (min-1
) 3300 3150 3750
2. Results of the emission tests.
Number of the relevant Directive and its amending acts applicable to the type-approval.
In the case of a Directive with two or more implementation stages, also the implementation
stage and the Euro level shall be indicated:
- 97/24/EC Chapter 5 as last amended by 2009/108/EC, stage A (2003) – for variant
AX700-UL;
- 97/24/EC Chapter 5 as last amended by 2013/60/EU, stage A (2003) – for variant
AX600-UL and AX800-UL
Variant/version AX700-UL/
AX700-UL,
AMX700-UL
AX600-UL/
AX600-UL,
AMX600-UL
AX800-UL/
AX800-UL,
AMX800-UL
Euro level (1)
Euro 2 Euro 2 Euro 2
2.1. Type I test:
CO (g/km) 0.805 0.696 0.574
HC (g/km) (3)
0.049 0.071 0.027
NOX (g/km) (3)
0.101 0.124 0.055
HC + NOX (g/km) (2)
-- -- --
CO2 (g/km) (2)
-- -- --
Fuel consumption
(l/100 km) (2)
-- -- --
2.2. Type II test:
CO (g/min) (2)
-- -- --
HC (g/min) (2)
-- -- --
Type-approval number: e4*2002/24*3058*04
WVTA 2002.24-2013.60 v6.01 Page 4 of 4
CO (% vol) (3)
at
normal idle speed
1.11 0.001 0.015
Specify the idle
speed (3) (4)
1600±100 1500±100 1500±100
CO (% vol) (3)
at high
idle speed
1.25 0.023 0.012
Specify the idle
speed (3) (4)
2800±100 3150±100 3750±100
Engine oil
temperature (3) (5)
88°C @1660 rpm
89°C @2880 rpm
86°C @1480 rpm
87°C @3190 rpm
92°C @1520 rpm
93°C @3760 rpm
3. Compression ignition engine:
Variant/version -- -- --
Corrected value of
absorption coefficient
(m-1
)
-- -- --
(1) See footnote 12 in Annex IV. (2) Only for L1e, L2e and L6e category vehicles. (3) For L-category vehicles within the scope of Article 1 of Directive 2002/24/EC with the exception of L1e, L2e and L6e vehicles. (4) Mention the measurement tolerance. (5) Applicable for four-stroke engines only.
TÜ V Rheinland Group
Test Report No.: 84-2002/24-00556/15-00
Vehicle type :
Manufacturer :
AX700-UL
ACCESS MOTOR CO., LTD.
Typprüfstelle Fahrzeuge/Fahrzeugteile Engineering Centre Shanghai Master_RDW_en_R13 Page 1 of 18 TÜ V Rheinland Kraftfahrt GmbH TÜ V Rheinland (Shanghai) Co., Ltd. 77-556e15-00.rdw
Am Grauen Stein, 51105 Cologne, Germany No. 177, 179, 189, Lane 777, Designation: RDW-99050014-06 West Guangzhong Road, Shanghai, P.R. China
T E S T R E P O R T
According to Council Directive on the approximation of
the laws of the Member States relating to the
Type-approval
of two or three-wheel motor vehicles
No.: 2002/24/EC
as last amended by
No.: 2013/60/EU
Approval Status
EC type – approval : e4*2002/24*3058*04
Structure of the Test Report: 0. General information
1. Tested vehicle(s)
2. Test record
3. List of appendices
4. Statement of conformity
The Test Report shall be reproduced and published in full by the client only. It shall however be
reproduced partially with the written permission of the Testing Laboratory only.
TÜ V Rheinland Group
Test Report No.: 84-2002/24-00556/15-00
Vehicle type :
Manufacturer :
AX700-UL
ACCESS MOTOR CO., LTD.
Typprüfstelle Fahrzeuge/Fahrzeugteile Engineering Centre Shanghai Master_RDW_en_R13 Page 2 of 18 TÜ V Rheinland Kraftfahrt GmbH TÜ V Rheinland (Shanghai) Co., Ltd. 77-556e15-00.rdw
Am Grauen Stein, 51105 Cologne, Germany No. 177, 179, 189, Lane 777, Designation: RDW-99050014-06 West Guangzhong Road, Shanghai, P.R. China
0. General information
0.1. Make (trade name of the
manufacturer)
: Access
0.2. Type : AX700-UL
0.3. Category of vehicle : L7e
0.4. Name and address of the
manufacturer
: ACCESS MOTOR CO., LTD.
No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone,
Tai-Pao City, Chia-Yi Hsien 612, Taiwan
0.5. No. of the information folder
-Date of issue
-Date of last change
:
:
:
AX700-UL-2002/24-04
January 14, 2014
May 25, 2015
TÜ V Rheinland Group
Test Report No.: 84-2002/24-00556/15-00
Vehicle type :
Manufacturer :
AX700-UL
ACCESS MOTOR CO., LTD.
Typprüfstelle Fahrzeuge/Fahrzeugteile Engineering Centre Shanghai Master_RDW_en_R13 Page 3 of 18 TÜ V Rheinland Kraftfahrt GmbH TÜ V Rheinland (Shanghai) Co., Ltd. 77-556e15-00.rdw
Am Grauen Stein, 51105 Cologne, Germany No. 177, 179, 189, Lane 777, Designation: RDW-99050014-06 West Guangzhong Road, Shanghai, P.R. China
1. Tested vehicle(s)
1.1. Description
1.1.1 Vehicle : Quadricycle
Commercial description : Access Motor
Type / variant(s) / version(s) : AX700-UL / AX600-UL / AMX600-UL
Identification number : RK3AX41235A000029
1.1.2 Condition of vehicle(s) : New, used, pretested
1.2. Worst case selection : The determination of worst case scenario was done
according QMA 1.301.005, section 6.2.2.2.
1.3. Remarks : All versions of the vehicle type as stated in the
information folder are covered by the tested vehicle
version(s) respectively.
TÜ V Rheinland Group
Test Report No.: 84-2002/24-00556/15-00
Vehicle type :
Manufacturer :
AX700-UL
ACCESS MOTOR CO., LTD.
Typprüfstelle Fahrzeuge/Fahrzeugteile Engineering Centre Shanghai Master_RDW_en_R13 Page 4 of 18 TÜ V Rheinland Kraftfahrt GmbH TÜ V Rheinland (Shanghai) Co., Ltd. 77-556e15-00.rdw
Am Grauen Stein, 51105 Cologne, Germany No. 177, 179, 189, Lane 777, Designation: RDW-99050014-06 West Guangzhong Road, Shanghai, P.R. China
2. Test record
2.1. Equipment for measuring and
testing
: The test facilities / measurement equipment used were in
compliance with the test requirements.
2.1.1 Specifications for the test site : Refer to the relevant Appendices
2.1.2 Subcontracting : Not applicable
2.2. Test results : See Appendix 1
2.2.1 Test results referring to
measurements
: All measurement results are listed and referred to the
respective limit(s) with judgment.
2.2.2 Attributive tests : Not applicable
2.2.3 Alternative test provisions : Not applicable
Remarks concerning extension : The vehicle type has been tested according to the
modification(s) mentioned in appendix 0.
The new parts meet the requirements of the Directives.
An actual practical test of the vehicle was not necessary.
The results of the previous test(s) are still valid.
2.3. Additional information : The results of the test refer exclusively to the vehicle(s)
mentioned under point 1. of this report.
Test site : ACCESS MOTOR CO., LTD., Chia-Yi, Taiwan
Test date : May 7 and June 15, 2015
2.4. Remarks : --
TÜ V Rheinland Group
Test Report No.: 84-2002/24-00556/15-00
Vehicle type :
Manufacturer :
AX700-UL
ACCESS MOTOR CO., LTD.
Typprüfstelle Fahrzeuge/Fahrzeugteile Engineering Centre Shanghai Master_RDW_en_R13 Page 5 of 18 TÜ V Rheinland Kraftfahrt GmbH TÜ V Rheinland (Shanghai) Co., Ltd. 77-556e15-00.rdw
Am Grauen Stein, 51105 Cologne, Germany No. 177, 179, 189, Lane 777, Designation: RDW-99050014-06 West Guangzhong Road, Shanghai, P.R. China
3. List of Appendices
0 List of modifications
1 Test minutes of frame directive : Pages 7 to 15
2 Test minutes of braking system : Not attached as not relevant to the extension
3 Test minutes of audible warning
device
: Page 16
4 Test minutes of maximum speed : Not attached as not applicable to the vehicle category
5 Test minutes of maximum
engine power and torque
: Not attached as not relevant to the extension
6 Test minutes of anti-pollution
devices
: Not attached as not relevant to the extension
7 Test minutes of anti-tampering
measures
: Not attached as not relevant to the extension
8 Test minutes of EMC : Not attached as not relevant to the extension
9 Test minutes of noise measuring : Not attached as not relevant to the extension
10 Test minutes of speedometer
measuring
: Pages 17 to 18
11 Information folder no.
(excluding drawings)
: AX700-UL-2002/24-04
4. Statement of conformity
The in point 0.5. mentioned information folder and the type described in that comply with the
requirements mentioned on page 1. With regard to the required level of performance to be achieved,
the tested items were representative for the type to be approved (see point 1.2.). The mentioned test
results refer to the vehicle(s) described under point 1.1. of this report.
Shanghai, 2015/08/21
KWU/HSIEHT
Expert Technical Service
TÜ V Rheinland Group
Test Report No.: 84-2002/24-00556/15-00
Vehicle type :
Manufacturer :
AX700-UL
ACCESS MOTOR CO., LTD.
Typprüfstelle Fahrzeuge/Fahrzeugteile Engineering Centre Shanghai Master_RDW_en_R13 Page 6 of 18 TÜ V Rheinland Kraftfahrt GmbH TÜ V Rheinland (Shanghai) Co., Ltd. 77-556e15-00.rdw
Am Grauen Stein, 51105 Cologne, Germany No. 177, 179, 189, Lane 777, Designation: RDW-99050014-06 West Guangzhong Road, Shanghai, P.R. China
List of modifications Appendix 0
Correction of : --
Modification of : --
Addition of : - Version AMX700-UL, AMX600-UL and AMX800-UL
with new front exterior parts including front lamp and
14” tyres
Deletion of : --
TÜ V Rheinland Group
Test Report No.: 84-2002/24-00556/15-00
Vehicle type :
Manufacturer :
AX700-UL
ACCESS MOTOR CO., LTD.
Typprüfstelle Fahrzeuge/Fahrzeugteile Engineering Centre Shanghai Master_RDW_en_R13 Page 7 of 18 TÜ V Rheinland Kraftfahrt GmbH TÜ V Rheinland (Shanghai) Co., Ltd. 77-556e15-00.rdw
Am Grauen Stein, 51105 Cologne, Germany No. 177, 179, 189, Lane 777, Designation: RDW-99050014-06 West Guangzhong Road, Shanghai, P.R. China
Test minutes of the frame directive Appendix 1
1. General
1.1. Make : Access
1.2. Type : AX700-UL
Variant(s) : AX700-UL, AX600-UL, AX800-UL
Version(s) : AX700-UL, AX600-UL, AX800-UL,
AMX700-UL, AMX600-UL, AMX800-UL
1.3. Name and address of manufacturer : ACCESS MOTOR CO., LTD.
No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone,
Tai-Pao City, Chia-Yi Hsien 612, Taiwan
1.4. Name and address of manufacturer’s
authorized representative
: Not applicable
2. General arrangement of vehicle
2.1. Category of vehicle : L7e
2.2. Maximum design speed : 60 km/h
According to SD 95/1/EC, amendment 2006/27/EC
Conformity checks : Requirements fulfilled
Approval number : Not applicable
2.3. Wheels
2.3.1 Number : 4
2.3.2 Symmetrical or asymmetrical
configuration
: Symmetrical
2.4. Frame layout diagram : See drawing No. 71000-A36-H00
TÜ V Rheinland Group
Test Report No.: 84-2002/24-00556/15-00
Vehicle type :
Manufacturer :
AX700-UL
ACCESS MOTOR CO., LTD.
Typprüfstelle Fahrzeuge/Fahrzeugteile Engineering Centre Shanghai Master_RDW_en_R13 Page 8 of 18 TÜ V Rheinland Kraftfahrt GmbH TÜ V Rheinland (Shanghai) Co., Ltd. 77-556e15-00.rdw
Am Grauen Stein, 51105 Cologne, Germany No. 177, 179, 189, Lane 777, Designation: RDW-99050014-06 West Guangzhong Road, Shanghai, P.R. China
3. Masses and dimensions : According to SD 93/93/EEC, amendment
2004/86/EC
Conformity checks : Requirements fulfilled
Approval number : Not applicable
3.1. Mass of vehicle in running order : See Information Document AX700-UL-2002/24-04,
2.1.
3.1.1 Distribution of that mass between the
axles
: See Information Document AX700-UL-2002/24-04,
2.1.1.
3.2. Mass of vehicle in running order
together with rider
: See Information Document AX700-UL-2002/24-04,
2.2.
3.2.1 Distribution of that mass between the
axles
: See Information Document AX700-UL-2002/24-04,
2.2.1.
3.3. Maximum technically permissible
mass declared by the manufacturer
: See Information Document AX700-UL-2002/24-04,
2.3.
3.3.1 Division of that mass between the
axles
: See Information Document AX700-UL-2002/24-04,
2.3.1.
3.3.2 Maximum technically permissible
mass on each of the axles
: See Information Document AX700-UL-2002/24-04,
2.3.2.
3.4. Vehicle length : Version AX700-UL, AX600-UL, AX800-UL:
2250±10 mm
Version AMX700-UL, AMX600-UL,
AMX800-UL: 2390±10 mm
3.5. Vehicle width : 1200±10 mm
3.6. Vehicle height : Version AX700-UL, AX600-UL, AX800-UL:
1495±10 mm
Version AMX700-UL, AMX600-UL,
AMX800-UL: 1520±10 mm
4. Engine
4.1. Manufacturer of engine : See Information Document AX700-UL-2002/24-04,
3.0.
TÜ V Rheinland Group
Test Report No.: 84-2002/24-00556/15-00
Vehicle type :
Manufacturer :
AX700-UL
ACCESS MOTOR CO., LTD.
Typprüfstelle Fahrzeuge/Fahrzeugteile Engineering Centre Shanghai Master_RDW_en_R13 Page 9 of 18 TÜ V Rheinland Kraftfahrt GmbH TÜ V Rheinland (Shanghai) Co., Ltd. 77-556e15-00.rdw
Am Grauen Stein, 51105 Cologne, Germany No. 177, 179, 189, Lane 777, Designation: RDW-99050014-06 West Guangzhong Road, Shanghai, P.R. China
4.2. Make : See Information Document AX700-UL-2002/24-04,
3.1.
4.3. Type : Variant AX700-UL: E20
Variant AX600-UL: E23
Variant AX800-UL: E24
4.4. Spark- or compression-ignition engine : Spark-ignition / compression-ignition engine
4.4.1 Operating cycle : See Information Document AX700-UL-2002/24-04,
3.2.1.1.
4.4.2 Cooling system : See Information Document AX700-UL-2002/24-04,
3.2.7.
4.4.3 Lubrication system : Pressure circulation wet-sump system
4.4.4 Number, arrangement and firing order
of cylinders
: See Information Document AX700-UL-2002/24-04,
3.2.1.2.
4.4.5 Bore, stroke and cylinder capacity : See Information Document AX700-UL-2002/24-04,
3.2.1.2.1. - 3.2.1.3.
4.4.6 Full drawing of induction system : See Information Document AX700-UL-2002/24-04,
3.2.8.3.
4.4.7 Compression ratio : See Information Document AX700-UL-2002/24-04,
3.2.1.4.
4.4.8 Maximum net power and maximum
net torque
: See Information Document AX700-UL-2002/24-04,
3.2.1.7. - 3.2.1.8., according to SD 95/1/EC,
amendment 2006/27/EC
Conformity checks : Requirements fulfilled,
for test results see appendix 5
Approval number : Not applicable
4.4.9 Fuel tank : According to SD 97/24/EC Chapter 6, amendment
2009/108/EC,
see Information Document AX700-UL-2002/24-04,
3.2.3.
TÜ V Rheinland Group
Test Report No.: 84-2002/24-00556/15-00
Vehicle type :
Manufacturer :
AX700-UL
ACCESS MOTOR CO., LTD.
Typprüfstelle Fahrzeuge/Fahrzeugteile Engineering Centre Shanghai Master_RDW_en_R13 Page 10 of 18 TÜ V Rheinland Kraftfahrt GmbH TÜ V Rheinland (Shanghai) Co., Ltd. 77-556e15-00.rdw
Am Grauen Stein, 51105 Cologne, Germany No. 177, 179, 189, Lane 777, Designation: RDW-99050014-06 West Guangzhong Road, Shanghai, P.R. China
Conformity checks : Requirements fulfilled,
report no.: 84-97/2406-00603/11
Approval number (installation) : Not applicable
Approval number (component) : See Information Document AX700-UL-2002/24-04,
3.2.3.4.
4.4.10 Fuel supply : See Information Document AX700-UL-2002/24-04,
3.2.4.
10.15. Anti-tampering measures for mopeds
and motorcycles
: Not applicable
Conformity checks : Not applicable
Approval number : Not applicable
4.4.11 Electrical system : See Information Document AX700-UL-2002/24-04,
3.2.5.
4.4.12 Generator : See Information Document AX700-UL-2002/24-04,
3.2.5.2.
10.3. Electromagnetic compatibility : According to SD 97/24/EC Chapter 8, amendment
2009/108/EC,
see Information Document AX700-UL-2002/24-04,
3.2.6.8.
Conformity checks : Requirements fulfilled,
for test results see appendix 8
Approval number : Not applicable
10.4. Sound level and exhaust system : According to SD 97/24/EC Chapter 9, amendment
2009/108/EC
Conformity checks : Requirements fulfilled,
for test results see appendix 9
Approval number : Not applicable
10.4.1 Make of exhaust system : See Information Document AX700-UL-2002/24-04,
3.2.9.
TÜ V Rheinland Group
Test Report No.: 84-2002/24-00556/15-00
Vehicle type :
Manufacturer :
AX700-UL
ACCESS MOTOR CO., LTD.
Typprüfstelle Fahrzeuge/Fahrzeugteile Engineering Centre Shanghai Master_RDW_en_R13 Page 11 of 18 TÜ V Rheinland Kraftfahrt GmbH TÜ V Rheinland (Shanghai) Co., Ltd. 77-556e15-00.rdw
Am Grauen Stein, 51105 Cologne, Germany No. 177, 179, 189, Lane 777, Designation: RDW-99050014-06 West Guangzhong Road, Shanghai, P.R. China
10.4.2 Type of exhaust system : One main muffler
10.4.3 Sound level
Stationary noise, dB(A) at min-1
: Variant AX700-UL: 85 / 3300
Variant AX600-UL: 83 / 3150
Variant AX800-UL: 88 / 3750
Noise when in motion in dB(A) : 80
4.4.13 Anti-pollution devices : According to SD 97/24/EC Chapter 5, amendment
2013/60/EU
Conformity checks : Requirements fulfilled,
for test results see appendix 6
Approval number : Not applicable
4.5. Electric traction motor : Not applicable
5. Transmission
Type : Manual / automatic
2.2. Maximum design speed : According to SD 95/1/EC, amendment 2006/27/EC,
see Information Document AX700-UL-2002/24-04,
4.6.
Conformity checks : Requirements fulfilled,
for test results see appendix 4
Approval number : Not applicable
10.12. Speedometer : According to SD 2000/7/EC,
see Information Document AX700-UL-2002/24-04,
4.7.
Conformity checks : Requirements fulfilled,
for test results see appendix 10
Approval number : Not applicable
TÜ V Rheinland Group
Test Report No.: 84-2002/24-00556/15-00
Vehicle type :
Manufacturer :
AX700-UL
ACCESS MOTOR CO., LTD.
Typprüfstelle Fahrzeuge/Fahrzeugteile Engineering Centre Shanghai Master_RDW_en_R13 Page 12 of 18 TÜ V Rheinland Kraftfahrt GmbH TÜ V Rheinland (Shanghai) Co., Ltd. 77-556e15-00.rdw
Am Grauen Stein, 51105 Cologne, Germany No. 177, 179, 189, Lane 777, Designation: RDW-99050014-06 West Guangzhong Road, Shanghai, P.R. China
6. Tyres : According to SD 97/24/EC Chapter 1, amendment
2009/108/EC,
see Information Document AX700-UL-2002/24-04,
5.2.
Conformity checks : Requirements fulfilled
Approval number : Not applicable
Tyres of any tyre manufacturer may be fitted
provided that they are of the same dimensions,
E/e-mark approved according to ECE-R75 or
97/24/EC, chapter 1 and of a load index of
36 (front tyre) / 42 (rear tyre) for version AX700-
UL, AX600-UL, AX800-UL or
37 (front tyre) / 42 (rear tyre) for version AMX700-
UL, AMX600-UL, AMX800-UL or more and a
speed index of F (all tyres) for all variants or more.
7. Braking system : According to SD 93/14/EEC, amendment
2006/27/EC,
see Information Document AX700-UL-2002/24-04,
7.
Conformity checks : Requirements fulfilled,
for test results see appendix 2
Approval number : Not applicable
8. Installation of lighting and light-
signalling devices
: According to SD 2009/67/EC, amendment
2013/60/EU,
see Information Document AX700-UL-2002/24-04,
8.2.
Conformity checks : Requirements fulfilled
Approval number : Not applicable
9. Lighting and light-signalling devices : According to SD 97/24/EC Chapter 2, amendment
2009/108/EC,
see Information Document AX700-UL-2002/24-04,
8.1.
Conformity checks : Requirements fulfilled
TÜ V Rheinland Group
Test Report No.: 84-2002/24-00556/15-00
Vehicle type :
Manufacturer :
AX700-UL
ACCESS MOTOR CO., LTD.
Typprüfstelle Fahrzeuge/Fahrzeugteile Engineering Centre Shanghai Master_RDW_en_R13 Page 13 of 18 TÜ V Rheinland Kraftfahrt GmbH TÜ V Rheinland (Shanghai) Co., Ltd. 77-556e15-00.rdw
Am Grauen Stein, 51105 Cologne, Germany No. 177, 179, 189, Lane 777, Designation: RDW-99050014-06 West Guangzhong Road, Shanghai, P.R. China
Approval number : See Information Document AX700-UL-2002/24-04,
8.1.
10. Miscellaneous
10.16. Coupling devices and their attachment : According to SD 97/24/EC Chapter 10, amendment
2009/108/EC,
see Information Document AX700-UL-2002/24-04,
9.1.
Conformity checks : Requirements fulfilled
Approval number : e4*97/24*97/24/10*3026*00 or
e4*97/24*97/24/10*0010*00
10.13. Identification of controls, tell-tales and
indicators
: According to SD 2009/80/EC,
see Information Document AX700-UL-2002/24-04,
9.2.
Conformity checks : Requirements fulfilled
Approval number : Not applicable
10.14. Statutory inscriptions : According to SD 2009/139/EC,
see Information Document AX700-UL-2002/24-04,
9.3.
Conformity checks : Requirements fulfilled
Approval number : Not applicable
Location of statutory plate : On the right side of rear frame body
10.8. Devices to prevent unauthorized use : According to SD 93/33/EEC, amendment
1999/23/EC,
see Information Document AX700-UL-2002/24-04,
9.4.
Conformity checks : Requirements fulfilled
Approval number : Not applicable
10.1. Audible warning device : According to SD 93/30/EEC,
see Information Document AX700-UL-2002/24-04,
9.5.
TÜ V Rheinland Group
Test Report No.: 84-2002/24-00556/15-00
Vehicle type :
Manufacturer :
AX700-UL
ACCESS MOTOR CO., LTD.
Typprüfstelle Fahrzeuge/Fahrzeugteile Engineering Centre Shanghai Master_RDW_en_R13 Page 14 of 18 TÜ V Rheinland Kraftfahrt GmbH TÜ V Rheinland (Shanghai) Co., Ltd. 77-556e15-00.rdw
Am Grauen Stein, 51105 Cologne, Germany No. 177, 179, 189, Lane 777, Designation: RDW-99050014-06 West Guangzhong Road, Shanghai, P.R. China
Conformity checks : Requirements fulfilled,
for test results see appendix 3
Approval number, annex II
(installation)
: Not applicable
Approval number, annex I
(component)
: See Information Document AX700-UL-2002/24-04,
9.5.4.
10.2. Location of rear registration plate : According to SD 2009/62/EC,
see Information Document AX700-UL-2002/24-04,
9.6.
Conformity checks : Requirements fulfilled
Approval number : Not applicable
10.6. External projections : According to SD 97/24/EC Chapter 3, amendment
2009/108/EC
Conformity checks : Requirements fulfilled
Approval number : Not applicable
B. Information relating solely to two-wheel mopeds and motorcycles
Not applicable
C. Information relating solely to three-wheel mopeds, motorcycles and quadricycles
10.9. Windows : Without (vehicle without bodywork)
10.5. Rear-view mirrors : According to SD 97/24/EC Chapter 4, amendment
2009/108/EC,
see Information Document AX700-UL-2002/24-04,
C 2.6.
Conformity checks : Requirements fulfilled
Approval number (installation) : Not applicable
TÜ V Rheinland Group
Test Report No.: 84-2002/24-00556/15-00
Vehicle type :
Manufacturer :
AX700-UL
ACCESS MOTOR CO., LTD.
Typprüfstelle Fahrzeuge/Fahrzeugteile Engineering Centre Shanghai Master_RDW_en_R13 Page 15 of 18 TÜ V Rheinland Kraftfahrt GmbH TÜ V Rheinland (Shanghai) Co., Ltd. 77-556e15-00.rdw
Am Grauen Stein, 51105 Cologne, Germany No. 177, 179, 189, Lane 777, Designation: RDW-99050014-06 West Guangzhong Road, Shanghai, P.R. China
Approval number (component) : See Information Document AX700-UL-2002/24-04,
C 2.6.2.
10.11. Anchorages for safety belts : Not applicable
Conformity checks : Not applicable
Approval number : Not applicable
TÜ V Rheinland Group
Test Report No.: 84-2002/24-00556/15-00
Vehicle type :
Manufacturer :
AX700-UL
ACCESS MOTOR CO., LTD.
Typprüfstelle Fahrzeuge/Fahrzeugteile Engineering Centre Shanghai Master_RDW_en_R13 Page 16 of 18 TÜ V Rheinland Kraftfahrt GmbH TÜ V Rheinland (Shanghai) Co., Ltd. 77-556e15-00.rdw
Am Grauen Stein, 51105 Cologne, Germany No. 177, 179, 189, Lane 777, Designation: RDW-99050014-06 West Guangzhong Road, Shanghai, P.R. China
Test minutes of audible warning device Appendix 3
0. Test condition : Version AMX600-UL was taken as the test
representative
0.1. Test date : May 7, 2015
0.2. Test site : Chia-Yi / Taiwan
1. Test facilities : The test equipment used was in compliance with the
requirements of the directive.
2. Test vehicle(s)
2.1. Type : AX700-UL
Variant : AX600-UL
Version : AMX600-UL
2.2. Identification number : RK3AX41235A000029
2.3. Type : Electromagnetic horn with disc resonator (DC horn)
2.4. Approval number : II E4 000014 II E9 00.6288
3. Test results : Passed Passed
3.1. Ambient noise in dB(A) : 45.1 43.2
3.2. Test voltage in V : 13.0 13.0
3.3. Max. sound pressure level in 7 m
distance in dB(A)
: 98.0 99.6
3.4. Height of microphone above the
ground in m
: 1.50 0.65
TÜ V Rheinland Group
Test Report No.: 84-2002/24-00556/15-00
Vehicle type :
Manufacturer :
AX700-UL
ACCESS MOTOR CO., LTD.
Typprüfstelle Fahrzeuge/Fahrzeugteile Engineering Centre Shanghai Master_RDW_en_R13 Page 17 of 18 TÜ V Rheinland Kraftfahrt GmbH TÜ V Rheinland (Shanghai) Co., Ltd. 77-556e15-00.rdw
Am Grauen Stein, 51105 Cologne, Germany No. 177, 179, 189, Lane 777, Designation: RDW-99050014-06 West Guangzhong Road, Shanghai, P.R. China
Test minutes of speedometer measuring Appendix 10
0. Test condition : Version AMX600-UL was taken as the test
representative
0.1. Test date : May 7, 2015
0.2. Test site : Chia-Yi / Taiwan
1. Test facilities : The test equipment used was in compliance with the
requirements of the directive.
2. Test vehicle(s)
2.1. Type : AX700-UL
Variant : AX600-UL
Version : AMX600-UL
2.2. Identification number : RK3AX41235A000029
3. Vehicle designed Vmax [km/h] : 60
4. Mass in running order [kg] : 374
5. Distribution [kg] Axle 1 : 205
Axle 2 : 169
6. Tyre dimensions Axle 1 : AT26×8-14
Axle 2 : AT26×10-14
6.1. Tyre pressure [kPa] Axle 1 : 55
Axle 2 : 55
7. Speedometer
7.1. Make(s) / type(s) : KOSO / A43
7.2. Speed indicated by : Dial / digital readout
TÜ V Rheinland Group
Test Report No.: 84-2002/24-00556/15-00
Vehicle type :
Manufacturer :
AX700-UL
ACCESS MOTOR CO., LTD.
Typprüfstelle Fahrzeuge/Fahrzeugteile Engineering Centre Shanghai Master_RDW_en_R13 Page 18 of 18 TÜ V Rheinland Kraftfahrt GmbH TÜ V Rheinland (Shanghai) Co., Ltd. 77-556e15-00.rdw
Am Grauen Stein, 51105 Cologne, Germany No. 177, 179, 189, Lane 777, Designation: RDW-99050014-06 West Guangzhong Road, Shanghai, P.R. China
7.3. Test speed(s) [km/h] : 40
8. Measurement
8.1. Temp. at speedometer (°C) [23±5°C] : 28
8.2. Test result : Passed
Test
No.
Displayed speed
“V1” (km/h)
Test speeds
“V2” (km/h)
Error
“V1-V2” (km/h) Limit (km/h)
1 45 40.0 5.0 8.0
2 46 40.0 6.0 8.0
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 1 / 23
2002/24/EC INFORMATION DOCUMENT
PART 1
A. INFORMATION RELATING JOINTLY TO MOPEDS, MOTOR CYCLES,
MOTOR TRICYCLES AND QUADRICYCLES
0. General
0.1. Make : Access
0.2. Type : AX700-UL
Variant : AX700-UL, AX600-UL, AX800-UL
Version : AX700-UL, AX600-UL, AX800-UL,
AMX700-UL, AMX600-UL, AMX800-UL
#
0.2.1. Commercial name : Access Motor, as option: SS250R, Hammel,
Quadzilla, Bogart Patriot, Nexmotor,
Tomahawk, Apollo, Spike, Speed, Maverick,
TKM, FOCUS, TENA, TRITON, MAX,
APACHE, Burelli, Warrior, GOES
0.3. Means of type identification if stated on
vehicle
: ???AX3???????????
0.3.1. Location of that means of identification : On the right side of frame body, see drawing
no.: 71000-A36-H00
0.4. Vehicle category : L7e
0.5. Name and address of manufacturer
Address
: Access Motor Co., Ltd.
No. 5, Chung-Hsin Rd., Chia-Tai Industrial
Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan
0.5.1. Name(s) and address(s) of assembly plants : Access Motor Co., Ltd.
No. 5, Chung-Hsin Rd., Chia-Tai Industrial
Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan
0.6. Name and address of manufacturer‘s
authorized representative, if any
: N/A
0.7. Location and method of affixing statutory
inscriptions to the chassis
: Riveted on the right side of frame body, see
drawing no.: 71000-A36-H00
0.7.1. The serial numbering of the type begins
with No
:
Version AX700-UL: RK3AX36204A000001
Version AX600-UL: RK3AX3R234A000001
Version AX800-UL: RK3AX38244A000001
Version AMX700-UL: RK3AX3X205A000001
Version AMX600-UL: RK3AX3C235A000001
Version AMX800-UL: RK3AX3L245A000001
#
#
#
0.8. Position and method of affixing the
component type-approval mark for
components and separate technical units
: Components approval marks are fixed by mold,
engraving of sticker to the components.
1. General arrangement of vehicles
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 2 / 23
1.1. Photos and/or drawings of a typical vehicle : See drawing no: 70000-A36-H00, 70000-A36-
H21, 70000-A36-H30, 70000-A36-H41 (version
AX700-UL, AX600-UL, AX800-UL);
70000-A44-H00, 70000-A44-H10, 70000-A44-
H20 (version AMX700-UL, AMX600-UL,
AMX800-UL)
#
1.2. Dimensional drawing of the complete
vehicle
: See drawing no: 70000-A36-H00, 70000-A36-
H21, 70000-A36-H30, 70000-A36-H41 (version
AX700-UL, AX600-UL, AX800-UL);
70000-A44-H00, 70000-A44-H10, 70000-A44-
H20 (version AMX700-UL, AMX600-UL,
AMX800-UL)
#
1.2.1. Wheelbase : 1440 mm
1.3. Number of axles and wheels : Two axles, two wheels on each axle
1.4. Position and arrangement of engine : Central and vertical
1.5. Number of seating positions : 1 or 2
1.6. Hand of drive – left or right : N/A
1.6.1. Vehicle is equipped to be driven in right-
hand or left-hand rule of the road traffic
: Right-hand rule of the road traffic
2. Masses
2.0. Unladen mass : Version AX700-UL, AX600-UL, AX800-UL:
348±5 kg
Version AMX700-UL, AMX600-UL, AMX800-
UL: 360±5 kg
#
2.1. Mass of vehicle in running order : Version AX700-UL, AX600-UL, AX800-UL:
362±5 kg
Version AMX700-UL, AMX600-UL, AMX800-
UL: 374±5 kg
#
2.1.1. Distribution of that mass between the axles : Version AX700-UL, AX600-UL, AX800-UL:
Front- 199 kg, rear- 163 kg
Version AMX700-U, AMX600-U, AMX800-U:
Front- 205 kg, rear- 169 kg
#
2.2. Mass of vehicle in running order, together
with rider
: Version AX700-UL, AX600-UL, AX800-UL:
437±5 kg
Version AMX700-UL, AMX600-UL, AMX800-
UL: 449±5 kg
#
2.2.1. Distribution of that mass between the axles : Version AX700-UL, AX600-UL, AX800-UL:
Front- 228 kg, rear- 209 kg
Version AMX700-U, AMX600-U, AMX800-U:
Front- 234 kg, rear- 215 kg
#
2.3. Maximum technically permissible mass
declared by the manufacturer
: Version AX700-UL, AX600-UL, AX800-UL:
542±5 kg
Version AMX700-UL, AMX600-UL, AMX800-
UL: 554±5 kg
#
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 3 / 23
2.3.1. Division of that mass between the axles : Version AX700-UL, AX600-UL, AX800-UL:
Front- 249 kg, rear- 293 kg
Version AMX700-U, AMX600-U, AMX800-U:
Front- 255 kg, rear- 299 kg
#
2.3.2. Maximum technically permissible mass on
each of the axles
: Version AX700-UL, AX600-UL, AX800-UL:
Front- 249 kg, rear- 293 kg
Version AMX700-U, AMX600-U, AMX800-U:
Front- 255 kg, rear- 299 kg
#
2.4. Maximum hill-starting ability at the
maximum technically permissible mass
declared by the manufacturer
: 10
2.5. Maximum tow-able mass : 174 kg
2.6. Maximum mass of the combination : Version AX700-UL, AX600-UL, AX800-UL:
716±5 kg
Version AMX700-UL, AMX600-UL, AMX800-
UL: 728±5 kg
#
3. Engine
3.0. Manufacturer : Access Motor Co., Ltd.
3.1. Make : Access
3.1.1. Type : Variant AX700-UL: E20
Variant AX600-UL: E23
Variant AX800-UL: E24
3.1.2. Location of engine number : Right side of the crankcase
3.2. Spark- or compression-ignition engine
3.2.1. Specific characteristics of the engine
3.2.1.1. Operating cycle : Spark ignition, four stroke
3.2.1.2. Number, arrangement and firing order of
cylinders
: One, vertical
3.2.1.2.1. Bore : Variant AX700-UL: Ø 102.0 mm
Variant AX600-UL: Ø 96.0 mm
Variant AX800-UL: Ø 104.0 mm
3.2.1.2.2. Stroke : Variant AX700-UL, AX600-UL: 84.0 mm
Variant AX800-UL: 92.0 mm
3.2.1.3. Cylinder capacity : Variant AX700-UL: 686 cm3
Variant AX600-UL: 608 cm3
Variant AX800-UL: 781 cm3
3.2.1.4. Compression ratio : Variant AX700-UL: 9.2±0.1
Variant AX600-UL: 10±0.1
Variant AX800-UL: 9.6±0.1
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 4 / 23
3.2.1.5. Drawings of cylinder head, piston(s),
piston rings and cylinder(s)
: See drawing no: 12100-E20-H00, 12200-E20-H00, 13300-E20-000, 13310-E20-000~1, 13310-E20-000~2, 13310-E20-000~3 (Variant: AX700-UL) 12100-E23-H00, 12200-E20-H00, 13300-E24-000, 13310-E12-100~1, 13310-E12-100~2, 13310-E12-100~3 (Variant: AX600-UL) 12100-E24-H00, 12200-E20-H00, 13300-E24-000, 13310-E24-000~1, 13310-E24-000~2, 13310-E24-000~3 (Variant: AX800-UL)
3.2.1.6. Idling speed min-1
: Variant AX700-UL: 1600±100 min-1
Variant AX600-UL: 1500±100 min-1
Variant AX800-UL: 1500±100 min-1
3.2.1.7. Maximum net power output : Variant AX700-UL: 10.80 kW at 4400 min-1
Variant AX600-UL: 12.44 kW at 4200 min-1
Variant AX800-UL: 14.65 kW at 5000 min-1
3.2.1.8. Net maximum torque : Variant AX700-UL: 40.60 Nm at 2000 min-1
Variant AX600-UL: 36.73 Nm at 2700 min-1
Variant AX800-UL: 40.91 Nm at 2650 min-1
3.2.2. Fuel : Diesel/ petrol/ mixture/ LPG/ other
3.2.3. Fuel tank
3.2.3.1. Maximum capacity : 21±0.2 L
3.2.3.2. Drawing of tank with indication of
materials used
: See drawing no: 12100-A27-H00
3.2.3.3. Diagram clearly indicating the position of
the tank on the vehicle
: See drawing no: 12100-A27-H00
3.2.3.4. Approval number of the fuel tank fitted : N/A
3.2.4. Fuel supply
3.2.4.1. Via carburetor(s) : Yes / no
3.2.4.1.1. Make(s) : N/A
3.2.4.1.2. Type(s) : N/A
3.2.4.1.3. Number fitted : N/A
3.2.4.1.4. Settings
3.2.4.1.4.1. Diffusers : N/A
3.2.4.1.4.2. Level in float chamber : N/A
3.2.4.1.4.3. Mass of float : N/A
3.2.4.1.4.4. Float needle : N/A
3.2.4.1.4.5. Fuel curve as a function of the air flow and
settings required in order to maintain that
curve
: N/A
3.2.4.1.5. Cold-starting system : N/A
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 5 / 23
3.2.4.1.5.1. Operating principle(s) : N/A
3.2.4.2. By fuel injection (solely in the case of
compression ignition)
: Yes / no
3.2.4.2.1. Description of system : N/A
3.2.4.2.2. Operating principle direct / indirect /
turbulence chamber injection
: N/A
3.2.4.2.3. Injection pump N/A
3.2.4.2.3.1. Make(s) : N/A
3.2.4.2.3.2. Type(s) : N/A
3.2.4.2.3.3. Maximum fuel flow rate mm3 / per stroke
or cycle at a pump rotational speed of min-1
or characteristic diagram
: N/A
3.2.4.2.3.4. Injection advance : N/A
3.2.4.2.3.5. Injection advance curve : N/A
3.2.4.2.3.6. Calibration procedure: test bench/engine : N/A
3.2.4.2.4. Regulator N/A
3.2.4.2.4.1. Type : N/A
3.2.4.2.4.2. Cut-off point : N/A
3.2.4.2.4.2.1. Cut-off point under load : N/A
3.2.4.2.4.2.2. Cut-off point under no load : N/A
3.2.4.2.4.3. Idling speed : N/A
3.2.4.2.5. Injection pipework : N/A
3.2.4.2.5.1. Length : N/A
3.2.4.2.5.2. Internal diameter : N/A
3.2.4.2.6. Injector(s) : N/A
3.2.4.2.6.1. Make(s) : N/A
3.2.4.2.6.2. Type(s) : N/A
3.2.4.2.6.3. Opening pressure or characteristic diagram : N/A
3.2.4.2.7. Cold starting system : N/A
3.2.4.2.7.1. Make(s) : N/A
3.2.4.2.7.2. Type(s) : N/A
3.2.4.2.7.3. Description : N/A
3.2.4.2.8. Secondary starting device : N/A
3.2.4.2.8.1. Make(s) : N/A
3.2.4.2.8.2. Type(s) : N/A
3.2.4.2.8.3. Description of system : N/A
3.2.4.3. By fuel injection (solely in the case of
spark-ignition)
: Yes / no
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 6 / 23
3.2.4.3.1. Description of system : EFI (Electronic Fuel Injection system integrating
with O2 sensor feedback)
3.2.4.3.2. Operating principle: injection into
Induction manifold (single/multiple
point)/direct injection/other (state which)
: Single point injection
3.2.4.3.2.1. Make(s) of the injection pump : BOSCH
3.2.4.3.2.2. Type(s) of the injection pump : Marking: F01RB0M081
3.2.4.3.3. Injectors: opening pressure
or characteristic diagram
: 300 kPa @ 12V
3.2.4.3.4. Injection advance : 0~360° CA
3.2.4.3.5. Cold-starting system Included in the EFI system
3.2.4.3.5.1. Operating principle(s) : A/F ratio controlled by the EFI system
(dependent on the parameter of the water temp.)
3.2.4.3.5.2. Operating/setting limits : -20 °C~ 40 °C
3.2.4.4. Fuel pump : Yes / no
3.2.5. Electrical equipment
3.2.5.1. Nominal voltage : 12V, negative earth
3.2.5.2. Generator
3.2.5.2.1. Type : Shihlin
3.2.5.2.2. Nominal power : 280W
3.2.6. Ignition
3.2.6.1. Make (s) : BOSCH
3.2.6.2. Type(s) : Variant AX700-UL: 61115-A36-000
Variant AX600-UL: 61115-A41-000
Variant AX800-UL: 61115-A38-000
3.2.6.3. Operating principle : Electronic Control Unit
3.2.6.4. Ignition advance curve or operating set
point
: See drawing no: 61115-A36-000
3.2.6.5. Static timing : 5 before TDC
3.2.6.6. Points gap : N/A
3.2.6.7. Dwell angle : N/A
3.2.6.8. Anti-radio interference system : Spark plug cap with resistor and resistive spark
plug
3.2.6.8.1. Terminology and drawing of anti-radio
interference equipment
: Spark plug: NGK R CR8E
Ignition coil: see drawing no: 61110-A27-000,
61111-A27-000
3.2.6.8.2. Indication of the nominal DC resistance
value and, in the case of resistive ignition
lead, statement of nominal resistance per
metre
: Plug cap: 10±1.25 kΩ
Spark plug: 5±1 kΩ
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 7 / 23
3.2.7. Cooling system : Liquid / air
3.2.7.1. Nominal setting for the engine-temperature
control device
: Control valve opened when water is more than
75±4 °C
3.2.7.2. Liquid
3.2.7.2.1. Nature of liquid : Long life coolant additive: 50%, water: 50%
3.2.7.2.2. Circulating pump(s) : Yes / no
3.2.7.3. Air
3.2.7.3.1. Blower : Yes / no
3.2.8. Induction system
3.2.8.1. Supercharging : Yes / no
3.2.8.1.1. Make(s) : N/A
3.2.8.1.2. Type(s) : N/A
3.2.8.1.3. Description of system : N/A
3.2.8.2. Intercooler : With / without
3.2.8.3. Description and drawings of induction
pipework and accessories (plenum
chamber, heating device, additional air
intakes, etc.)
: See drawing no: 16410-E20-000
3.2.8.3.1. Description of induction manifold : See drawing no: 16410-E20-000
3.2.8.3.2. Air filter, drawings : See drawing no: 17300-E20-H00, 17300-E20-
000-1, 17300-E20-000-2
3.2.8.3.2.1. Make(s) : Cheng Tong
3.2.8.3.2.2. Type(s) : E20 (marking: 17300-E20-000-2)
3.2.8.3.3. Inlet silencer, drawings : See drawing no: 17320-E20-000
3.2.8.3.3.1 Make(s) : Cheng Tong
3.2.8.3.3.2 Type(s) : E20
3.2.9. Exhaust system
3.2.9.1. Drawing of complete exhaust system : See drawing no: 12160-A36-000_01, 12164-
A27-H00
3.2.10. Minimum cross-section of the inlet and
exhaust ports
: See drawing no: 12200-E20-H00
3.2.11. Induction system or equivalent data
3.2.11.1. Maximum, valve lift, opening and closing
angles in relation to the dead centres, or
data concerning the settings of other
possible systems
: See drawing no: 25100-E20-H00
3.2.11.2. Reference and/or setting ranges : 0.06~0.1 mm
3.2.12. Measures taken against air pollution
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 8 / 23
3.2.12.1. Device for recycling crankcase gases,
solely in the case of four-stroke engines
: See drawing no: 11350-E20-H00 (R-crankcase
venthole system)
3.2.12.2. Additional anti-pollution devices (if any,
and if not covered by another heading)
: No
3.2.12.2.1. Catalytic converter : Yes / no
3.2.12.2.1.1. Number of catalytic converters and
elements
: 1
3.2.12.2.1.2. Dimensions, shape and volume of the
catalytic converter(s)
: See drawing no: 12165-A27-H00
3.2.12.2.1.3. Type of catalytic action : 3 way catalytic converter
3.2.12.2.1.4. Total charge of precious metal : See drawing no: 12165-A27-H00
3.2.12.2.1.5. Relative concentration : See drawing no: 12165-A27-H00
3.2.12.2.1.6. Substrate (structure and material) : See drawing no: 12165-A27-H00
3.2.12.2.1.7. Cell density : 100 cpsi
3.2.12.2.1.8. Type of casing for the catalytic converter(s) : See drawing no: 12165-A27-H00
3.2.12.2.1.9. Location of the catalytic converter(s) : See drawing no: 12160-A36-000_01
3.2.12.2.2. Oxygen sensor : Yes / no
3.2.12.2.2.1. Type : 0258006937 LSF4
3.2.12.2.2.2. Location : See drawing no. 12164-A27-H00
3.2.12.2.2.3. Control range : Rich > 600 mV, Lean < 450 mV
3.2.12.2.3. Air injection : Yes / no
3.2.12.2.3.1. Type : Pulse air
3.2.12.2.4. Exhaust gas recirculation : Yes / no
3.2.12.2.4.1. Characteristics : N/A
3.2.12.2.5.. Other systems : N/A
3.2.13. Location of the coefficient of absorption
symbol
: N/A
3.3. Electric traction motor
3.3.1. Type : N/A
3.3.1.1. Maximum continuous rated power : N/A
3.3.1.2. Operating voltage : N/A
3.3.2. Battery
3.3.2.1. Number of cells : N/A
3.3.2.2. Mass : N/A
3.3.2.3. Capacity : N/A
3.3.2.4. Location : N/A
3.4. Other motors or combinations of motors : N/A
3.5. Cooling system temperatures permitted by the manufacturer
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 9 / 23
3.5.1. Liquid cooling
3.5.1.1. Maximum temperature at outlet : 90 °C
3.5.2. Air cooling : N/A
3.5.2.1. Reference point : N/A
3.5.2.2. Maximum temperature at reference point : N/A
3.6. Lubrication system
3.6.1. Description of system : Lubricant oil splashed to the cylinder camshaft
by oil pump
3.6.1.1. Location of oil reservoir : Below the crankcase
3.6.1.2. Feed system : Oil pump
3.6.2. Lubricant mixed with the fuel
3.6.2.1. Percentage : N/A
3.6.3. Oil cooler : Yes / no
3.6.3.1. Drawing(s) : N/A
3.6.3.1.1. Make(s) : N/A
3.6.3.1.2. Type(s) : N/A
4. Transmission
4.1. Diagram of transmission system : See drawing no: 22100-E20-H00
4.2. Type : CVT
4.3. Clutch : Centrifugal
4.4. Gearbox
4.4.1. Type : Automatic / manual
4.4.2. Method of selection : By hand / foot
4.5. Gear ratios
N R1 R2 R3 Rt
Minimum continuously
variable transmission
1
2
…
Maximum continuously
variable transmission
Reverse gear
1:1
1:1
1:1
H gear: 1:4.119
L gear: 1:6.951
H gear: 1:1.955
L gear: 1:3.299
1:7.174
1:3.667
1:3.667
1:3.667
H gear: 1:15.104
L gear: 1:25.489
H gear: 1:7.169
L gear: 1:12.097
1:26.307
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 10 / 23
N : gear ratio
R1 : primary ratio (ratio of engine speed to rotational speed of primary gearbox shaft).
R2 : secondary ratio (ratio of rotational speed of primary shaft to rotational speed of secondary
shaft in gearbox).
R3 : final drive ratio (ratio of rotational speed of gearbox output shaft to rotational speed of
driven wheels).
Rt : overall ratio
4.5.1. Brief description of the electrical and/or
electronic components used in the
transmission
: N/A
4.6. Maximum speed of vehicle and gear in which
it is reached
:
60 km/h (@ H gear)
4.7. Speedometer
4.7.1. Make(s) : KOSO
4.7.2. Type(s) : A27, A27-1, A43 #
4.7.3. Photographs and/or drawings of the
complete system
: See drawing no: 63300-A27-H01, 63300-A27-H11,
62120-A27-H00, 63300-A43-H01, 63300-A43-H11
#
4.7.4. speed range displayed : 63300-A27-H01: 0~ 150 km/h (0~ 93 mph)
63300-A27-H11: 0~ 199 km/h (0~ 124 mph)
63300-A43-H01: 0~ 150 km/h (0~ 93 mph)
#
4.7.5. Tolerance of the measuring mechanism of the
speedometer
: Version AX700-UL, AX600-UL, AX800-UL:
km/h 37
Tolerance 0~ +8.1 %
Tolerance
Range
0~ 3.0 km/h
Version AMX700-UL, AMX600-UL,
AMX800-UL:
km/h 40
Tolerance 0~ +15 %
Tolerance
Range
0~ 6.0 km/h
#
4.7.6. Technical constant of the speedometer : Setting parameter: 450 (60 km/h @ 1500 rpm)
4.7.7. Method of operation and description of the
drive mechanism
: Magnetic detect, digital display with blue back-
lighting
4.7.8. Overall transmission ratio of the drive
mechanism
: N/A
5. Suspension
5.1. Drawing of suspension arrangement : See drawing no: 70000-A36-H00, 70000-A36-H21,
70000-A36-H30, 70000-A36-H41
5.1.1. Brief description of the electrical and/or
electronic components used in the suspension
: N/A
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 11 / 23
5.2. Tyres (category, dimensions and maximum
loading) and rims (standard type)
: Version AX700-UL, AX600-UL, AX800-UL:
Front
Category Normal
Size AT25×8-12
Max load 155 kg
Rim 6×12
Rear
Category Normal
Size AT25×10-12
Max load 190 kg
Rim 7.0×12
Version AMX700-UL, AMX600-UL,
AMX800-UL:
Front
Category Normal
Size AT26×8-14
Max load 160 kg
Rim 6×14 or 7×14
Rear
Category Normal
Size AT26×10-14
Max load 195 kg
Rim 7×14 or 7.5×14
As option
Front
Category Normal
Size AT25×8-12
Max load 155 kg
Rim 612
Rear
Category Normal
Size AT25×10-12
Max load 190 kg
Rim 7.012
#
5.2.1. Nominal rolling circumference : Version AX700-UL, AX600-UL, AX800-UL:
Front & rear- 1995 mm
Version AMX700-UL, AMX600-UL,
AMX800-UL:
Front & rear- 2075 mm or 1995 mm
#
5.2.2. Tire pressures recommended by the
manufacturer
: 35 kPa
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 12 / 23
5.2.3. Tyre/wheel combinations : Version AX700-UL, AX600-UL, AX800-UL:
Front- 25×8-12 / 6×12
Rear- 25×10-12 / 7.0×12
Version AMX700-UL, AMX600-UL,
AMX800-UL:
Front- 26×8-14 / 7×14 or 6×14
Rear- 26×10-14 / 7.5×14 or 7×14
As option
Front- 25×8-12 / 6×12
Rear- 25×10-12 / 7.0×12
#
5.2.4. Minimum-speed category symbol compatible
with the theoretical maximum design speed of
the vehicle
: F
5.2.5. Minimum load-capacity index with the
maximum load on each tyre
: Version AX700-UL, AX600-UL, AX800-UL:
Front- 36, rear- 42
Version AMX700-UL, AMX600-UL,
AMX800-UL: Front- 37, rear- 42
#
5.2.6. Categories of use compatible for the vehicle : Normal
6. Steering
6.1. steering gear and control
6.1.1. Type of gear : N/A (handle bar on the front shaft steering)
6.1.2. Brief description of the electrical and/or
electronic components used in the steering
system
: N/A
7. Braking
7.1. Diagram of braking devices : See drawing no: 31115-A27-H00 (system A),
31115-A27-H30 (system B)
7.2. Front and rear brakes, disc and/or drum : Front and rear- disc
7.2.1. Make(s) : Yun Chen, as option: Horng Fuu
7.2.2. Type(s) : Yun Chen:
Front- 31335-A13-000 (RH), 31336-A13-000 (LH)
Rear- 31345-A27-000 (RH), 31346-A27-000 (LH)
Horng Fuu:
Front- 31335-A13-010 (RH), 31336-A13-010 (LH)
Rear- 31345-A27-020 (RH), 31346-A27-020 (LH),
as option: 31345-A27-010~1, 31345-A27-010~2
(RH), 31346-A27-010~1, 31346-A27-010~2 (LH)
7.3. Drawing of parts of the brake system
7.3.1. Shoes and/or pads : N/A
7.3.2. Linings and/or pads : See drawing no:
Front- 31337-A13-000~1
Rear- 31337-A03-001~1, 31337-A03-001~2
7.3.3. Brake levers and/or pedals : Brake levers:
see drawing no: 31405-A03-001, 31460-A03-000
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 13 / 23
Brake pedal: see drawing no: 31408-A27-000
7.3.4. Hydraulic reservoirs : See drawing no:
31405-A03-001, 31460-A03-000, 31406-A27-000
(Yun Chen), 31406-A32-010 (Horng Fuu)
7.4. Other devices: drawing and description : Mechanical parking brake device acting on the rear
axle, see drawing no: 31115-A27-H00, 31470-A27-
000, 31340-A13-000
7.5. Brief description of the electrical and/or
electronic components used in the braking
system
: N/A
8. Lighting and light-signaling devices
Version: AX700-UL, AX600-UL, AX800-UL
Trade Mark Type Quantity/
Color Tell Tale Approval No. Remark
Driving lamp JUTE JUTE PJ-H 2 / White
E9-001067 Max 53.4
lux
Passing lamp JUTE JUTE PJ-L 2 / White N.A. E9-001066 --
Front position
lamp JUTE JUTE PJ- H 2 / White
Illumination
of
speedometer
E9-50R-001066 --
Front direction
indicator WAMA ou SB 82-A003R/L 2 / Amber
E6-50R-000053 --
Front direction
indicator
(optional)
JUTE JUTE W013 2 / Amber
E4-6R-016962 Version B
Rear direction
Indicator WAMA ou SB 82-A003R/L 2 / Amber
E6-50R-000053 --
Rear direction
Indicator
(optional)
JUTE JUTE TL006 2 / Amber
E9-016395 --
Rear position
Lamp SB SB14-001 1 / Red
Illumination
of
speedometer
E4-50R-0013256 --
Rear position
Lamp (optional) JUTE JUTE TL006 2 / Red
Illumination
of
speedometer
E9-026395
Stop lamp SB SB14-001 1 / Red N.A. E4-50R-0013256 --
Stop lamp
(optional) JUTE JUTE TL006 2 / Red N.A. E9-026395
License Plate
illuminator JUTE PL004 1 / White N.A. E4-50R-001780 --
Rear retro
reflector JUTE 9605 JUTE 9605 2 / Red N.A.
E13*03R00*03R0
2*0279*01 --
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 14 / 23
Rear retro
reflector
(optional)
JUTE 9823 2 / Red N.A. E11-023578 --
Rear retro
reflector DBM or K-LITE KM-202 2 / Red N.A. E9-021269 --
Rear fog lamp FUAN or FOT FUAN 0089 1 / Red
E9-001240 --
Version: AMX700-UL, AMX600-UL, AMX800-UL #
Trade Mark Type Quantity/
Color Tell Tale Approval No. Remark
Driving lamp ACCESSMOTOR 62205-A43-000/
62200-A43-000 2 / White
E4-112R-0124075 60,080 cd
Passing lamp ACCESSMOTOR 62205-A43-000/
62200-A43-000 2 / White N.A. E4-112R-0124075 --
Front position
lamp
ACCESSMOTOR 62205-A43-000/
62200-A43-000 2 / White
E4-7R-0224075 --
Daytime running
lamp
ACCESSMOTOR 62205-A43-000/
62200-A43-000 2 / White N.A. E4-87R-0024075 --
Front direction
indicator
ACCESSMOTOR 62205-A43-000/
62200-A43-000 2 / Amber
E4-6R-0124075 --
Rear direction
Indicator WAMA ou SB 82-A003R/L 2 / Amber
E6-50R-000053 --
Rear direction
Indicator
(optional)
JUTE JUTE TL006 2 / Amber
E9-016395 --
Rear position
Lamp SB SB14-001 1 / Red
Illumination
of
speedometer
E4-50R-0013256 --
Rear position
Lamp (optional) JUTE JUTE TL006 2 / Red
Illumination
of
speedometer
E9-026395
Stop lamp SB SB14-001 1 / Red N.A. E4-50R-0013256 --
Stop lamp
(optional) JUTE JUTE TL006 2 / Red N.A. E9-026395
License Plate
illuminator JUTE PL004 1 / White N.A. E4-50R-001780 --
Rear retro
reflector JUTE JUTE 9605 2 / Red N.A.
E13*03R00*03R02
*0279*01 --
Rear retro
reflector JUTE 9823 2 / Red N.A. E11-023578 --
Rear retro
reflector
(optional)
DBM or K-LITE KM-202 2 / Red N.A. E9-021269 --
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 15 / 23
Rear fog lamp FUAN or FOT FUAN 0089 1 / Red
E9-001240 --
8.2. Diagram showing the location of the lighting
and light-signaling devices
: See drawing no: 70000-A36-H00, 70000-A36-H21,
70000-A36-H30, 70000-A36-H41 (version AX700-
UL, AX600-UL, AX800-UL);
70000-A44-H00, 70000-A44-H10, 70000-A44-H20
(version AMX700-UL, AMX600-UL, AMX800-
UL)
#
8.3. Hazard warning lamps : Yes
8.4. Additional requirements relating to special
vehicles
: N/A
8.5. Brief description of the electrical and/or
electronic components used in the lighting
system and in the light-signaling system
: N/A
9. Equipment
9.1. Coupling devices
9.1.1. Type : Hook/ring/other (A50-X)
9.1.2. Photographs and/ or drawing showing the
position and the construction of the coupling
devices
: See drawing no: 70000-A27-H10-2, 71403-A27-
H10, 71402-A20-H01
9.2. Arrangement and identification of controls, tell-tales and indicators
9.2.1. Photographs and/or drawings of the
arrangement of the symbols, controls, tell-
tales and indicators
: See drawing no: 61101-A27-000, 63300-A27-H01,
63300-A43-H11
#
9.3. Statutory inscriptions
9.3.1. Photographs and/or drawings showing the
location of the statutory inscriptions and the
chassis number
: See drawing no: 71000-A36-H00
9.3.2. Photographs and/or drawings showing the
official part of the inscriptions
: See drawing no:
71237-A36-H00, 71237-A41-H00, 71237-A38-H00
(version AX700-UL, AX600-UL, AX800-UL);
71237-A44-H00, 71237-A46-H00, 71237-A49-H00
(version AMX700-UL, AMX600-UL, AMX800-
UL)
#
9.3.3. Photographs and/or drawings of the chassis
number
: See drawing no: 71236-A36-H00, 71236-A36-H02 #
9.4. Device(s) to protect against unauthorized use
9.4.1. Type of device(s) : Type 1
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 16 / 23
9.4.2. Summary description of device(s) used : Steering shaft is locked to the frame body by a
lock pin, see drawing no: 70000-A36-H00, 70000-
A36-H21, 70000-A36-H30, 70000-A36-H41
(version AX700-UL, AX600-UL, AX800-UL);
70000-A44-H00, 70000-A44-H10, 70000-A44-H20
(version AMX700-UL, AMX600-UL, AMX800-
UL)
#
9.5. Audible warning device(s)
9.5.1 Summary description of device(s) used and : One electromagnetic DC horn
9.5.2. Make(s) : CHEN LEN
As optional: LGHORN, HOOTHORN, LG
9.5.3. Type(s) : CL-2
As optional: DL1590
9.5.4. Type-approval mark : II-E4-000014
As optional: II-E9-006288
9.5.5. Drawing(s) showing the location of the
audible warning device(s) in relation to the
structure of the vehicle
: See drawing no: 70000-A36-H00, 70000-A36-H21,
70000-A36-H30, 70000-A36-H41 (version AX700-
UL, AX600-UL, AX800-UL);
70000-A44-H00, 70000-A44-H10, 70000-A44-H20
(version AMX700-UL, AMX600-UL, AMX800-
UL)
#
9.5.6. Details of the method of attachment,
including the part of the vehicle structure to
which the audible warning device(s) is (are)
attached
: See drawing no: 70000-A36-H00, 70000-A36-H21,
70000-A36-H30, 70000-A36-H41 (version AX700-
UL, AX600-UL, AX800-UL);
70000-A44-H00, 70000-A44-H10, 70000-A44-H20
(version AMX700-UL, AMX600-UL, AMX800-
UL)
#
9.6. Location of rear registration plate : See drawing no: 70000-A36-H00, 70000-A36-H21,
70000-A36-H30, 70000-A36-H41 (version AX700-
UL, AX600-UL, AX800-UL);
70000-A44-H00, 70000-A44-H10, 70000-A44-H20
(version AMX700-UL, AMX600-UL, AMX800-
UL)
#
9.6.1. Inclination of plane in relation to the vertical : 28°
B. INFORMATION RELATING SOLELY TO TWO-WHEEL MOPEDS AND
MOTORCYCLES
Not applicable
C. INFORMATION RELATING SOLELY TO THREE-WHEEL MOPEDS, MOTOR
TRICYCLES AND QUADRICYCLES
1. Dimensions and masses
1.1. Dimensions to be complied with when building unbodied chassis
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 17 / 23
1.1.1 Length : Version AX700-UL, AX600-UL, AX800-UL:
2250±10 mm
Version AMX700-UL, AMX600-UL,
AMX800-UL: 2390±10 mm
#
1.1.2. Width : 1200±10 mm
1.1.3. Unladen height : Version AX700-UL, AX600-UL, AX800-UL:
1495±10 mm
Version AMX700-UL, AMX600-UL,
AMX800-UL: 1520±10 mm
#
1.1.4. Front overhang : Version AX700-UL, AX600-UL, AX800-UL:
420±10 mm
Version AMX700-UL, AMX600-UL,
AMX800-UL: 590±10 mm
#
1.1.5. Rear overhang : Version AX700-UL, AX600-UL, AX800-UL:
390±10 mm
Version AMX700-UL, AMX600-UL,
AMX800-UL: 360±10 mm
#
1.1.6. Limit position for centre of gravity of
bodied vehicle
: N/A
1.2. Masses
1.2.1. Maximum payload declared by
manufacturer
: 105 kg
2. Equipment
2.1. Bodywork
2.1.1. Nature of bodywork : N/A
2.1.2. General dimensional arrangement drawing
of inside
: N/A
2.1.3. General dimensional arrangement drawing
of outside
: N/A
2.1.4. Materials and methods of manufacture : N/A
2.1.5. Passenger doors, locks and hinges : N/A
2.1.6. Configuration, dimensions, direction and
maximum opening angle of doors
: N/A
2.1.7. Drawing of locks and hinges and their
location in the doors
: N/A
2.1.8. Technical description of locks and hinges : N/A
2.2. Windscreen and other glazing
2.2.1. Windscreen
2.2.1.1. Materials used : N/A
2.2.2. Other glazing
2.2.2.1. Materials used : N/A
2.3. Windscreen wiper(s)
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 18 / 23
2.3.1. Detailed technical description : N/A
2.4. windscreen washer(s)
2.4.1. Detailed technical description : N/A
2.5. Defrosting and demisting
2.5.1. Detailed technical description : N/A
2.6. Rear-view mirror(s)
2.6.1. Make : FU
2.6.2. Type-approval mark : L E11 001087
2.6.3. Variant : N/A
2.6.4. Drawing(s) showing the location of the
rear-view mirror(s) in relation to the
structure of the vehicle
: See drawing no: 70000-A36-H00, 70000-A36-H21,
70000-A36-H30, 70000-A36-H41 (version AX700-
UL, AX600-UL, AX800-UL);
70000-A44-H00, 70000-A44-H10, 70000-A44-H20
(version AMX700-UL, AMX600-UL, AMX800-
UL)
#
2.6.5. Detailed information on the method of
attachment, including that part of the
structure of the vehicle to which the rear-
view mirror is attached
: Mirrors are mounted on the handle bar by using
screws
2.7. Seats
2.7.1. Number : 1 or 2
2.7.2. Location : Center of vehicle
2.7.3. Coordinates or drawing of the R point
2.7.3.1. Driving seat : N/A
2.7.3.2. Other seats : N/A
2.7.4. Intended seat-back inclination
2.7.4.1. Driving seat : N/A
2.7.4.2. Other seats : N/A
2.7.5. Seat adjustment range, where appropriate
2.7.5.1. Driving seat : N/A
2.7.5.2. Other seats : N/A
2.8. Passenger-compartment heating system
2.8.1. Summary description of type of vehicle in
respect of the heating system if this uses
heat from the liquid engine coolant
: N/A
2.8.2. Detailed description of the type of the
vehicle in respect of the heating system if
this uses the cooling air or exhaust gases as
a heat source, including
: N/A
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 19 / 23
2.8.2.1. An overall drawing of the heating system
giving its location on the vehicle
: N/A
2.8.2.2. An overall drawing of the heat exchanger
used in systems utilizing the heat from the
exhaust gases, or of the parts where that
exchange takes place
: N/A
2.8.2.3. A sectional drawing of the heat exchanger
or parts where heat exchange takes place,
together with a statement of the wall
thickness, of the materials used and the
characteristics of their surface
: N/A
2.8.2.4. Specifications regarding the method of
manufacture and technical data relating to
other major components of the heating
system, such as the fan
: N/A
2.9. Safety belts
2.9.1. Number and location of safety belts,
together with a reference to the seats where
that type of equipment may be installed
: N/A
2.10. Anchorages
2.10.1. Number and location of the anchorages : N/A
2.10.2. Photographs and/or drawings of the
bodywork showing the true, effective
location and dimensions of the anchorages,
together with an indication of the R-point
position
: N/A
2.10.3. Drawings of the anchorages and the parts of
the structure of the vehicle to which they
are attached
: N/A
2.10.4. Designation of the types of belts(*)
authorized for attachment to the anchorages
on the vehicle
: N/A
2.10.5. Description of a specific type of belt, one
anchorage of which is attached to the seat
back-rest or incorporates an energy-
dissipation device
: N/A
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 20 / 23
PART 2 SEPARATE DIRECTIVE APPROVAL NUMBERS
The following information shall be supplied on the vehicle to be type approved with regard to existing system,
separate technical unit or component approvals(*):
Heading
No
Separate Directive
No
Subject Approval No (1) Extension
date
Variants
and
versions
covered
18 95/1/EC Maximum torque and
maximum net power of
engine
-- -- --
19
97/24/EC (C7) Anti-tampering
measures for mopeds
and motorcycles
-- -- --
20 97/24/EC (C6) Fuel tank -- -- --
25 95/1/EC Maximum design speed
of vehicle -- -- --
26 93/93/EEC Masses and dimensions -- -- --
27 97/24/EC (C10) Trailer coupling
devices
-- -- --
28 97/24/EC (C5) Anti-air pollution
measures
-- -- --
29 97/24/EC (C1) Tyres -- -- --
31 93/14/EEC Braking system -- -- --
32 2009/67/EC Installation of lighting
and light-signaling
devices on the vehicle
-- -- --
33 97/24/EC (C2) Lighting and light-
signaling devices
-- -- --
34 93/30/EEC Audible warning
device
-- -- --
35 2009/62/EC Position for the
mounting of rear
registration plate
-- -- --
36 97/24/EC (C8) Electromagnetic
compatibility
-- -- --
37 97/24/EC (C9) Sound level and -- -- --
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 21 / 23
exhaust system
38 97/24/EC (C4) Rear-view mirror(s) -- -- --
39 97/24/EC (C3) External projections -- -- --
40 2009/78/EC Stand (except in the
case of vehicles having
three or more wheels)
-- -- --
41 93/33/EEC Devices to prevent
unauthorized use of the
vehicle
-- -- --
42 97/24/EC (C12) Windows; windscreen
wipers; windscreen
washers; and so on
-- -- --
43 2009/79/EC Passenger hand-hold
for two-wheel vehicles
-- -- --
44 97/24/EC (C11) Anchorage points for
safety belts and safety
belts
-- -- --
45 2000/7/EC Speedometer -- -- --
46 2009/80/EC Identification of
controls, tell-tales and
indicators
-- -- --
47 2009/139/EC Statutory inscriptions -- -- --
(1) Examples are given in Annex V.
(*) Information is not required in respect of systems, separate technical units or components which are to be
included in the examination or testing for the granting of whole vehicle type approval.
Note: The heading numbers are aligned with Annex I (list of requirements).
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 22 / 23
LIST OF CONTENTS
Item Title Drawing No. Notes
1. Frame 71000-A36-H00
2. Vehicle over view 70000-A36-H00
3. Vehicle over view 70000-A36-H21
4. Vehicle over view 70000-A36-H30
5. Vehicle over view 70000-A36-H41
6. Vehicle over view 70000-A44-H00 #
7. Vehicle over view 70000-A44-H10 #
8. Vehicle over view 70000-A44-H20 #
9. Cylinder 12100-E20-H00
10. Cylinder 12100-E23-H00
11. Cylinder 12100-E24-H00
12. Cylinder head 12200-E20-H00
13. Piston 13300-E20-000
14. Piston 13300-E23-000
15. Piston 13300-E24-000
16. Piston ring (1st) 13310-E20-000~1
17. Piston ring (2nd) 13310-E20-000~2
18. Piston ring (oil) 13310-E20-000~3
19. Piston ring (1st) 13310-E12-100~1
20. Piston ring (2nd) 13310-E12-100~2
21. Piston ring (oil) 13310-E12-100~3
22. Piston ring (1st) 13310-E24-000~1
23. Piston ring (2nd) 13310-E24-000~2
24. Piston ring (oil) 13310-E24-000~3
25. Fuel cup comp 12100-A27-H00
26. ECU 61115-A36-000
27. ECU 61115-A41-000
28. ECU 61115-A38-000
29. Ignition coil 61110-A27-000
30. Plug cap 61111-A27-000
31. Intake pipe 16410-E20-000
32. Air filter Assy 17300-E20-H00
33. Case, AIR/C 17300-E20-000-1
34. Cover, AIR/C 17300-E20-000-2
35. Inlet silencer 17320-E20-000
36. Exhaust muffler comp 12160-A36-000_01
37. Front Exhaust Pipe 12164-A27-H00
38. Valve angle 25100-E20-H00
39. R-crankcase venthole system 11350-E20-H00
40. Catalyst 12165-A27-H00
41. Transmission system 22100-E20-H00
42. Speedometer 63300-A27-H01
43. Speedometer 63300-A27-H11
44. Speedometer 63300-A43-H01 #
Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875
Issue date: May 25, 2015 Doc. No.: AX700-UL-2002/24-04
Extension Application
PAGE 23 / 23
45. Speedometer 63300-A43-H11 #
46. Speedometer system 62120-A27-H00
47. Diagram of braking system 31115-A27-H00
48. Diagram of braking system 31115-A27-H30
49. Pad (Front) 31337-A13-000~1
50. Inner pad (rear) / Outer pad (rear) 31337-A03-001~1 & ~2
51. Inner pad (rear) / Outer pad (rear) 31337-A03-000~1 & ~2
52. Brake lever Ass’y (LH) 31405-A03-001
53. Brake lever Assy (RH) 31460-A03-000
54. Brake pedal 31408-A27-000
55. Master cylinder 31406-A27-000
56. Master cylinder 31406-A32-010
57. Mechanical parking brake lever 31470-A27-000
58. Caliper-parking 31340-A13-000
59. Front brake caliper (RH) 31335-A13-000
60. Front brake caliper (LH) 31336-A13-000
61. Rear brake caliper (RH) 31345-A27-000
62. Rear brake caliper (LH) 31346-A27-000
63. Front brake caliper (RH) 31335-A13-010
64. Front brake caliper (LH) 31336-A13-010
65. Rear brake caliper (RH) 31345-A27-020
66. Rear brake caliper (RH) 31345-A27-010~1&2
67. Rear brake caliper (LH) 31346-A27-010~1&2
68. Rear brake caliper (LH) 31346-A27-020
69. Front and Rear disc 31305-A13-000
70. Rear disc 31350-A27-000
71. Cable adapter 83111-A27-000
72. Telltales, controls and indicators 61101-A27-000
73. Manufacturer’s data plate 71237-A36-H00
74. Manufacturer’s data plate 71237-A41-H00
75. Manufacturer’s data plate 71237-A38-H00
76. Manufacturer’s data plate 71237-A44-H00 #
77. Manufacturer’s data plate 71237-A46-H00 #
78. Manufacturer’s data plate 71237-A49-H00 #
79. VIN code 71236-A36-H01
80. VIN code 71236-A36-H02 #
81. Radiator Assembly 15230-A27-000
82. O2 sensor 63215-A27-H00
83. Electrical circuit diagram A27 (AX700)
84. Injector 16250-E20-000
85. Throttle Body 16100-E20-000
86. Overall view 70000-A27-H10-2
87. Bracket Assy 71403-A27-H10
88. Coupling Ball 71402-A20-H01
1
A
REV.
修正
紀錄
Revision record
未標
示之
公差
表D
EC. X. =
±1.0X
.X = ±0.5
X.XX = ±0.25
AN
GLE =
±2°
0
製圖
DR
AWN
日期
DATE
材質
及規
格 M
ATER
IAL&S
IZE
表面
處理
SUR
FACE FIN
ISH
熱處
理 H
EAT TR
EAT
審圖
CH
ECKED
核准
AP
PR
OV
ED日
期 D
ATE
圖紙
PAPER
數量
QTY
比例
SC
ALE
單位
UN
IT
圖號
DW
G N
O.
圖名
DW
G N
AME
2015/5/11
70000-A44-H
00
Vehicle over view
台1
B
23
45
67
8 87
65
43
mm
☆雍
御企
業股
份有
限公
司智
慧財
產,
非經
同意
請勿
複製
!!☆
修訂
處核
准
日期
修訂
者Redactor
Approved
Date
Location
R-7301-02-3
呂宛
庭
720
504
2015/5
°82
Rear registration Plate lam
p30
80
Registration plate
681
2390
320
60
1120
1440590
360
710
Audible w
arning devices
AV
IN code
B
Luggage rack
C
785
860
815
820
700
Rear view
mirrors
(Types: FU FP-316)
800 for FP-316
530 128230
785
830 Manufacturer's data plate
Tail lamp
Rear direction indicator
Rear suspension
1520
720
755
825
820
845
7701200
435
Dipped beam
VIN
code
Front suspension
90
A
Main beam
Front direction indicator
620
DR
L
Front position lamp
Rear retro reflector
Types: JUTE
9605 or KM-202)
Manufacturer's data plate
1
A
REV.
修正
紀錄
Revision record
未標
示之
公差
表D
EC. X. =
±1.0X
.X = ±0.5
X.XX = ±0.25
AN
GLE =
±2°
0
製圖
DR
AWN
日期
DATE
材質
及規
格 M
ATER
IAL&S
IZE
表面
處理
SUR
FACE FIN
ISH
熱處
理 H
EAT TR
EAT
審圖
CH
ECKED
核准
AP
PR
OV
ED日
期 D
ATE
圖紙
PAPER
數量
QTY
比例
SC
ALE
單位
UN
IT
圖號
DW
G N
O.
圖名
DW
G N
AME
2015/5/11
70000-A44-H
10
Vehicle over view
台1
B
23
45
67
8 87
65
43
mm
☆雍
御企
業股
份有
限公
司智
慧財
產,
非經
同意
請勿
複製
!!☆
修訂
處核
准
日期
修訂
者Redactor
Approved
Date
Location
R-7301-02-3
呂宛
庭
720
504
2015/5
°82
Rear registration Plate lam
p30
80
Registration plate
681
2390
320
601120
1440590
360
710
Audible w
arning devices
AV
IN code
B
Luggage rack
C1520
720
755
825
820
845
7701200
435
Dipped beam
VIN
code
Front suspension
90
A
Main beam
Front direction indicator
620
DR
L
Front position lamp
795
850
801
841
700
Tail lamp
Rear view
mirrors
(Types: FU FP-316)
800 for FP-316
570 128230
821
440
860 Manufacturer's data plate
Rear retro reflector (Type: 9823)
Rear direction indicator
Tail lamp
Rear suspension
Rear direction indicator
Rear Fog lam
p(Type: FU
AN
0089)
Manufacturer's data plate
1
A
REV.
修正
紀錄
Revision record
未標
示之
公差
表D
EC. X. =
±1.0X
.X = ±0.5
X.XX = ±0.25
AN
GLE =
±2°
0
製圖
DR
AWN
日期
DATE
材質
及規
格 M
ATER
IAL&S
IZE
表面
處理
SUR
FACE FIN
ISH
熱處
理 H
EAT TR
EAT
審圖
CH
ECKED
核准
AP
PR
OV
ED日
期 D
ATE
圖紙
PAPER
數量
QTY
比例
SC
ALE
單位
UN
IT
圖號
DW
G N
O.
圖名
DW
G N
AME
2015/5/11
70000-A44-H
20
Vehicle over view
台1
B
23
45
67
8 87
65
43
mm
☆雍
御企
業股
份有
限公
司智
慧財
產,
非經
同意
請勿
複製
!!☆
修訂
處核
准
日期
修訂
者Redactor
Approved
Date
Location
R-7301-02-3
呂宛
庭
720
504
2015/5
°82
Rear registration Plate lam
p30
80
Registration plate
681
2390
320
60
1120
1440590
360
710
Audible w
arning devices
AV
IN code
B
Luggage rack
C1520
720
755
825
820
845
7701200
435
Dipped beam
VIN
code
Front suspension
90
A
Main beam
Front direction indicator
620
DR
L
Front position lamp
795
850
801
841
700
Tail lamp
Rear view
mirrors
(Types: FU FP-316)
800 for FP-316
570 128230
821
440
860
Manufacturer's data plate
Rear retro reflector (Type: 9823)
Rear direction indicator
Tail lamp
Rear suspension
Rear direction indicator
Manufacturer's data plate
A
5
DCB
12
34
A DCB
34
5
R-7301-02-4
21
未標
示之
公差
表D
EC. X. = ±
1.0X
.X = ±
0.5X
.XX = ±
0.25A
NG
LE = ±
2°
REV.
修正
紀錄
Revision record
1
製圖
DR
AWN
日期
DA
TE
材質
及規
格 M
ATERIA
L&SIZE
表面
處理
SUR
FACE FIN
ISH
熱處
理 H
EA
T TREAT
審圖
CH
ECKED
核准
APPR
OV
ED日
期 D
ATE
圖紙
PAPER
數量
QTY
比例
SCALE
單位
UN
IT
圖號
DW
G N
O.
圖名
DW
G N
AME
台
mm
修訂
處核
准
日期
修訂
者Redactor
Approved
Date
Location
莊宗耀
2015/06/23
63300-A43
-H01
速度表總成
1 A4
Manufacturer’s data plate
71237-A44-H
00
雍御
企業
股份
有限
公司
智慧
財產
,非
經同
意請
勿複
製!!
12
3
554 4
3
DD
CC
A BBA
Location修
訂處
Date
Redactor
Access Motor Co., Ltd.
1
台核
准
雍御企業股份有限公司
日期
修訂
者修
正記
錄 R
evision recordR
EV.
mm
A4
呂宛
庭2015/5/16
1
Manufacturer’s data plate
71237-A46-H
00
雍御
企業
股份
有限
公司
智慧
財產
,非
經同
意請
勿複
製!!
12
3
554 4
3
DD
CC
A BBA
Location修
訂處
Date
Redactor
Access Motor Co., Ltd.
1
台核
准
雍御企業股份有限公司
日期
修訂
者修
正記
錄 R
evision recordR
EV.
mm
A4
呂宛
庭2015/5/16
1
Manufacturer’s data plate
71237-A49-H
00
雍御
企業
股份
有限
公司
智慧
財產
,非
經同
意請
勿複
製!!
12
3
554 4
3
DD
CC
A BBA
Location修
訂處
Date
Redactor
Access Motor Co., Ltd.
1
台核
准
雍御企業股份有限公司
日期
修訂
者修
正記
錄 R
evision recordR
EV.
mm
A4
呂宛
庭2015/5/16
1
RK3 AX3 C 20 5 A 000001
WM
I Code (A
ccess Motor C
o.,Ltd)
Serial No.
Assem
bly plantA
ssembly year
雍御
企業
股份
有限
公司
智慧
財產
,非
經同
意請
勿複
製!!
12
3
554 4
3
DD
CC
A BBA
Location修
訂處
Date
Redactor
Access Motor Co., Ltd.
1
台核
准
雍御企業股份有限公司
日期
修訂
者修
正記
錄 R
evision recordR
EV.
mm
A4
呂宛
庭2015/5/16
1
VIN
code
71236-A36-H
02
23= Variant A
X600-U
L(600 Liquid C
ooling Engine)24= V
ariant AX
800-UL
(800 Liquid Cooling Engine)
X= V
ersion AM
X700-U
LL= V
ersion AM
X800-U
LType
20= Variant A
X700-U
L(700 Liquid C
ooling Engine)
C= V
ersion AM
X600-U
L