advanced lincmos rail-to-rail very low-power ......25°c 200 1500 input offset voltage µv full...
TRANSCRIPT
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
1POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
Output Swing Includes Both Supply Rails
Low Noise . . . 19 nV/√Hz Typ at f = 1 kHz
Low Input Bias Current . . . 1 pA Typ
Fully Specified for Both Single-Supply andSplit-Supply Operation
Very Low Power . . . 35 µA Per Channel Typ
Common-Mode Input Voltage RangeIncludes Negative Rail
Low Input Offset Voltage 850 µV Max at TA = 25°C (TLC225xA)
Macromodel Included
Performance Upgrades for the TS27L2/L4and TLC27L2/L4
Available in Q–Temp Automotive HighRel Automotive ApplicationsConfiguration Control / Print SupportQualification to Automotive Standards
description
The TLC2252 and TLC2254 are dual andquadruple operational amplifiers from TexasInstruments. Both devices exhibit rail-to-railoutput performance for increased dynamic rangein single- or split-supply applications. TheTLC225x family consumes only 35 µA of supplycurrent per channel. This micropower operationmakes them good choices for battery-poweredapplications. The noise performance has beendramatically improved over previous generationsof CMOS amplifiers. Looking at Figure 1, theTLC225x has a noise level of 19 nV/√Hz at 1kHz;four times lower than competitive micropowersolutions.
The TLC225x amplifiers, exhibiting high inputimpedance and low noise, are excellent forsmall-signal conditioning for high-impedancesources, such as piezoelectric transducers.Because of the micropower dissipation levels,these devices work well in hand-held monitoringand remote-sensing applications. In addition, therail-to-rail output feature with single or splitsupplies makes this family a great choice when interfacing with analog-to-digital converters (ADCs). Forprecision applications, the TLC225xA family is available and has a maximum input offset voltage of 850 µV. Thisfamily is fully characterized at 5 V and ±5 V.
The TLC2252/4 also makes great upgrades to the TLC27L2/L4 or TS27L2/L4 in standard designs. They offerincreased output dynamic range, lower noise voltage, and lower input offset voltage. This enhanced feature setallows them to be used in a wider range of applications. For applications that require higher output drive andwider input voltage ranges, see the TLV2432 and TLV2442 devices. If the design requires single amplifiers,please see the TLV2211/21/31 family. These devices are single rail-to-rail operational amplifiers in the SOT-23package. Their small size and low power consumption, make them ideal for high density, battery-poweredequipment.
Copyright 2001, Texas Instruments IncorporatedPRODUCTION DATA information is current as of publication date.Products conform to specifications per the terms of Texas Instrumentsstandard warranty. Production processing does not necessarily includetesting of all parameters.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications ofTexas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Advanced LinCMOS is a trademark of Texas Instruments.
Figure 1
VN
– E
qu
ival
ent
Inp
ut
No
ise
Vo
ltag
e –
nv/
/Hz
f – Frequency – Hz
EQUIVALENT INPUT NOISE VOLTAGEvs
FREQUENCY
nV
/H
zV
n
40
20
10
0
60
30
50
101 102 103 104
VDD = 5 VRS = 20 ΩTA = 25°C
On products compliant to MIL-PRF-38535, all parameters are testedunless otherwise noted. On all other products, productionprocessing does not necessarily include testing of all parameters.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC2252 AVAILABLE OPTIONS
PACKAGED DEVICES
TAVIOmaxAT 25°C
SMALLOUTLINE†
(D)
CHIPCARRIER
(FK)
CERAMICDIP(JG)
PLASTICDIP(P)
TSSOP‡
(PW)
CERAMICFLATPACK
(U)
0°C to 70°C 1500 µV TLC2252CD — — TLC2252CP TLC2252CPW —
40°C to 125°C850 µV TLC2252AID — — TLC2252AIP TLC2252AIPW —
–40°C to 125°Cµ
1500 µV TLC2252ID — — TLC2252IP — —
40°C to 125°C850 µV TLC2252AQD — — — — —
–40°C to 125°Cµ
1500 µV TLC2252QD — — — — —
–55°C to 125°C850 µV
1500 µV——
TLC2252AMFKTLC2252MFK
TLC2252AMJGTLC2252MJG
——
——
TLC2252AMUTLC2252MU
† The D packages are available taped and reeled. Add R suffix to device type (e.g., TLC2262CDR).‡ The PW package is available only left-ended taped and reeled.§ Chip forms are tested at 25°C only.
TLC2254 AVAILABLE OPTIONS
PACKAGED DEVICES
TAVIOmaxAT 25°C
SMALL OUTLINE†
(D)
CHIP CARRIER
(FK)
CERAMIC DIP(J)
PLASTIC DIP(N)
TSSOP‡
(PW)
CERAMICFLATPACK
(W)
0°C to70°C 1500 µV TLC2254CD — — TLC2254CN TLC2254CPW —
–40°C to 850 µV TLC2254AID — — TLC2254AIN TLC2254AIPW —
125°Cµ
1500 µV TLC2254ID — — TLC2254IN — —
–40°C to 850 µV TLC2254AQD — — — — —125°C
µ1500 µV TLC2254QD — — — — —
–55°C to 850 µV — TLC2254AMFK TLC2254AMJ — — TLC2254AMW125°C
µ1500 µV — TLC2254MFK TLC2254MJ — — TLC2254MW
† The D packages are available taped and reeled. Add R suffix to the device type (e.g., TLC2254CDR).‡ The PW package is available only left-end taped and reeled. Chips are tested at 25°C.§ Chip forms are tested at 25°C only.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
3POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC2252M, TLC2252AM . . . JG PACKAGE(TOP VIEW)
TLC2252C, TLC2252ACTLC2252I, TLC2252AI
TLC2252Q, TLC2252AQD, P, OR PW PACKAGE
(TOP VIEW)
1
2
3
4
8
7
6
5
1OUT1IN–1IN+
VDD– /GND
VDD+2OUT2IN–2IN+
NCVCC +2OUT2IN –2IN +
NC1OUT1IN –1IN +
VCC– /GND
1
2
3
4
5
10
9
8
7
6
TLC2262M, TLC2252AM . . . U PACKAGE(TOP VIEW)
1
2
3
4
8
7
6
5
1OUT1IN–1IN+
VDD– /GND
VDD+2OUT2IN–2IN+
3 2 1 20 19
9 10 11 12 13
4
5
6
7
8
18
17
16
15
14
NC2OUTNC2IN–NC
NC1IN–
NC1IN+
NC
NC
1OU
TN
C2I
N+
NC
NC
NC
NC
VD
D+
VD
D–
TLC2252M, TLC2252AM . . . FK PACKAGE(TOP VIEW)
/GN
D
1
2
3
4
5
6
7
14
13
12
11
10
9
8
1OUT1IN–1IN+
VDD+2IN+2IN–
2OUT
4OUT4IN–4IN+VDD– /GND3IN+3IN–3OUT
3 2 1 20 19
9 10 11 12 13
4
5
6
7
8
18
17
16
15
14
4IN+NCVCC– /GNDNC3IN+
1IN+NC
VCC+NC
2IN+
1IN
–1O
UT
NC
3OU
T3I
N –
4OU
T4I
N –
2IN
–2O
UT
NC
TLC2254M, TLC2254AMFK PACKAGE(TOP VIEW)
TLC2254C, TLC2254ACTLC2254I, TLC2254AI
TLC2254Q, TLC2254AQD, N, OR PW PACKAGE
(TOP VIEW)
1
2
3
4
5
6
7
14
13
12
11
10
9
8
1OUT1IN–1IN+
VDD+2IN+2IN–
2OUT
4OUT4IN–4IN+VDD– /GND3IN+3IN–3OUT
TLC2254M, TLC2254AMJ OR W PACKAGE
(TOP VIEW)
NC – No internal connection
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
equivalent schematic (each amplifier)
Q3 Q6 Q9 Q12 Q14 Q16
Q2 Q5 Q7 Q8 Q10 Q11
D1
Q17Q15Q13
Q4Q1
R5
C1
VDD+
IN+
IN–
R3 R4 R1 R2
OUT
VDD– /GND
R6
ACTUAL DEVICE COMPONENT COUNT†
COMPONENT TLC2252 TLC2254
Transistors 38 76
Resistors 30 56
Diodes 9 18
Capacitors 3 6† Includes both amplifiers and all ESD, bias, and trim circuitry
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
5POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VDD+ (see Note 1) 8 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supply voltage, VDD– (see Note 1) –8 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Differential input voltage, VID (see Note 2) ±16 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input voltage, VI (any input, see Note 1) ±8 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input current, II (each input) ±5 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Output current, IO ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Total current into VDD+ ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Total current out of VDD– ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Duration of short-circuit current at (or below) 25°C (see Note 3) unlimited. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous total dissipation See Dissipation Rating Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating free-air temperature range, TA: C suffix 0°C to 70°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I suffix –40°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Q suffix –40°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M suffix –55°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, Tstg –65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds 260°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, andfunctional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is notimplied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VDD+ and VDD – .2. Differential voltages are at IN+ with respect to IN–. Excessive current flows when input is brought below VDD– – 0.3 V.3. The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum
dissipation rating is not exceeded.
DISSIPATION RATING TABLE
PACKAGETA ≤ 25°C DERATING FACTOR TA = 70°C TA = 85°C TA = 125°C
PACKAGE APOWER RATING ABOVE TA = 25°C
APOWER RATING
APOWER RATING
APOWER RATING
D–8 724 mW 5.8 mW/°C 464 mW 377 mW 144 mW
D–14 950 mW 7.6 mW/°C 608 mW 450 mW 190 mW
FK 1375 mW 11.0 mW/°C 880 mW 715 mW 275 mW
J 1375 mW 11.0 mW/°C 880 mW 715 mW 275 mW
JG 1050 mW 8.4 mW/°C 672 mW 546 mW 275 mW
N 1150 mW 9.2 mW/°C 736 mW 736 mW —
P 1000 mW 8.0 mW/°C 640 mW 520 mW —
PW–8 525 mW 4.2 mW/°C 336 mW 273 mW —
PW–14 700 mW 5.6 mW/°C 448 mW 448 mW —
U 700 mW 5.5 mW/°C 246 mW 330 mW 150 mW
W 700 mW 5.5 mW/°C 246 mW 330 mW 150 mW
recommended operating conditions
C SUFFIX I SUFFIX Q SUFFIX M SUFFIXUNIT
MIN MAX MIN MAX MIN MAX MIN MAXUNIT
Supply voltage, VDD± ±2.2 ±8 ±2.2 ±8 ±2.2 ±8 ±2.2 ±8 V
Input voltage range, VI VDD– VDD+ –1.5 VDD– VDD+ –1.5 VDD– VDD+ –1.5 VDD– VDD+ –1.5 V
Common-mode input voltage, VIC VDD– VDD+ –1.5 VDD– VDD+ –1.5 VDD– VDD+ –1.5 VDD– VDD+ –1.5 V
Operating free-air temperature, TA 0 70 –40 125 –40 125 –55 125 °C
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER TEST CONDITIONS T †TLC2252C
UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX
UNIT
VIO Input offset voltage25°C 200 1500
µVVIO Input offset voltageFull range 1750
µV
αVIO Temperature coefficient of input offset voltage25°C
0 5 µV/°CαVIO Temperature coefficient of input offset voltageto 70°C 0.5 µV/°C
Input offset voltage long-term drift (see Note 4) VIC = 0,VO = 0
VDD± = ±2.5 V,RS = 50 Ω
25°C 0.003 µV/mo
IIO Input offset current
VO = 0, RS = 50 Ω25°C 0.5 60
pAIIO Input offset currentFull range 100
pA
IIB Input bias current25°C 1 60
pAIIB Input bias currentFull range 100
pA
0 –0.325°C
0to
0.3to
VICR Common mode input voltage range RS = 50 Ω |VIO | ≤ 5 mV4 4.2
VVICR Common-mode input voltage range RS = 50 Ω, |VIO | ≤ 5 mV0
V
Full range0tog
3.5
IOH = –20 µA 25°C 4.98
VOH High level output voltage IOH = 75 µA25°C 4.9 4.94
VVOH High-level output voltage IOH = –75 µAFull range 4.8
V
IOH = –150 µA 25°C 4.8 4.88
VIC = 2.5 V, IOL = 50 µA 25°C 0.01
VIC = 2 5 V IOL = 500 µA25°C 0.09 0.15
VIC = 2.5 V, IOL = 500 µAFull range 0.15
VOL Low-level output voltageVIC = 2 5 V IOL = 1 A
25°C 0.2 0.3 VVIC = 2.5 V, IOL = 1 A
Full range 0.3
VIC = 2 5 V IOL = 4 A25°C 0.7 1
VIC = 2.5 V, IOL = 4 AFull range 1.2
V 2 5 V R 100 kΩ‡25°C 100 350
AVD Large-signal differential voltage amplificationVIC = 2.5 V,VO = 1 V to 4 V
RL = 100 kهFull range 10 V/mVVD g g g VO = 1 V to 4 V
RL = 1 MΩ‡ 25°C 1700
rid Differential input resistance 25°C 1012 Ω
ric Common-mode input resistance 25°C 1012 Ω
cic Common-mode input capacitance f = 10 kHz, P package 25°C 8 pF
zo Closed-loop output impedance f = 25 kHz, AV = 10 25°C 200 Ω
CMRR Common mode rejection ratioVIC = 0 to 2.7 V, VO = 2.5 V, 25°C 70 83
dBCMRR Common-mode rejection ratio IC , O ,RS = 50 Ω Full range 70
dB
kSVR Supply voltage rejection ratio (∆VDD/∆VIO)VDD = 4.4 V to 16 V, 25°C 80 95
dBkSVR Supply-voltage rejection ratio (∆VDD/∆VIO) DD ,VIC = VDD/2, No load Full range 80
dB
IDD Supply current VO = 2 5 V No load25°C 70 125
µAIDD Supply current VO = 2.5 V, No loadFull range 150
µA
† Full range is 0°C to 70°C.‡ Referenced to 2.5 VNOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
7POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER TEST CONDITIONS T †TLC2252C
UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX
UNIT
VO 1 5 V to 3 5 V RL 100 kΩ‡25°C 0.07 0.12
SR Slew rate at unity gain VO = 1.5 V to 3.5 V, RL = 100 kΩ‡,CL = 100 pF‡ Full
0 05V/µs
CL = 100 F‡range
0.05
V Equivalent input noise voltagef = 10 Hz 25°C 36
nV/√HzVn Equivalent input noise voltagef = 1 kHz 25°C 19
nV/√Hz
VN(PP) Peak to peak equivalent input noise voltagef = 0.1 Hz to 1 Hz 25°C 0.7
µVVN(PP) Peak-to-peak equivalent input noise voltagef = 0.1 Hz to 10 Hz 25°C 1.1
µV
In Equivalent input noise current 25°C 0.6 fA√Hz
THD + N Total harmonic distortion plus noiseVO = 0.5 V to 2.5 V,f 10 kHz
AV = 125°C
0.2%THD + N Total harmonic distortion plus noise f = 10 kHz,
RL = 50 kΩ‡ AV = 1025°C
1%
Gain-bandwidth productf = 10 kHz, CL = 100 pF‡
RL = 50 kΩ‡, 25°C 0.2 MHz
BOM Maximum output-swing bandwidthVO(PP) = 2 V, RL = 50 kه,
AV = 1, CL = 100 pF‡ 25°C 30 kHz
φm Phase margin at unity gainRL = 50 kΩ‡ CL = 100 pF‡ 25°C 63°
Gain marginRL = 50 kΩ‡, CL = 100 pF‡
25°C 15 dB† Full range is 0°C to 70°C.‡ Referenced to 2.5 V
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwisespecified)
PARAMETER TEST CONDITIONS T †TLC2252C
UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX
UNIT
VIO Input offset voltage
V
25°C 200 1500µVVIO Input offset voltage
V
Full range 1750µV
αVIO Temperature coefficient of input offset voltage
V
25°C0 5 µV/°CαVIO Temperature coefficient of input offset voltage
Vto 70°C 0.5 µV/°C
Input offset voltage long-term drift (see Note 4) VIC = 0,RS = 50 Ω
VO = 0, 25°C 0.003 µV/mo
IIO Input offset current
RS = 50 Ω25°C 0.5 60
pAIIO Input offset currentFull range 100
pA
IIB Input bias current25°C 1 60
pAIIB Input bias currentFull range 100
pA
–5 –5.325°C
5to
5.3to
VICR Common mode input voltage range |VIO | ≤5 mV RS = 50 Ω4 4.2
VVICR Common-mode input voltage range |VIO | ≤5 mV, RS = 50 Ω–5
V
Full range5tog
3.5
IO = –20 µA 25°C 4.98
VOM Maximum positive peak output voltage IO = 100 µA25°C 4.9 4.93
VVOM+ Maximum positive peak output voltage IO = –100 µAFull range 4.7
V
IO = –200 µA 25°C 4.8 4.86
VIC = 0, IO = 50 µA 25°C –4.99
VIC = 0 IO = 500 µA25°C –4.85 –4.91
VIC = 0, IO = 500 µAFull range –4.85
VOM– Maximum negative peak output voltageVIC = 0 IO = 1 A
25°C –4.7 –4.8 VVIC = 0, IO = 1 A
Full range –4.7
VIC = 0 IO = 4 A25°C –4 –4.3
VIC = 0, IO = 4 AFull range –3.8
RL = 100 kΩ25°C 45 650
AVD Large-signal differential voltage amplification VO = ±4 VRL = 100 kΩ
Full range 10 V/mV
RL = 1 MΩ 25°C 3000
rid Differential input resistance 25°C 1012 Ω
ric Common-mode input resistance 25°C 1012 Ω
cic Common-mode input capacitance f = 10 kHz, P package 25°C 8 pF
zo Closed-loop output impedance f = 25 kHz, AV = 10 25°C 190 Ω
CMRR Common mode rejection ratioVIC = –5 V to 2.7 V, 25°C 75 88
dBCMRR Common-mode rejection ratioVO = 0, RS = 50 Ω Full range 75
dB
kSVR Supply voltage rejection ratio (∆VDD± /∆VIO)VDD± = 2.2 V to ±8 V, 25°C 80 95
dBkSVR Supply-voltage rejection ratio (∆VDD± /∆VIO)VIC = 0, No load Full range 80
dB
IDD Supply current VO = 0 No load25°C 80 125
µAIDD Supply current VO = 0, No loadFull range 150
µA
† Full range is 0°C to 70°C.NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
9POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER TEST CONDITIONS T †TLC2252C
UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX
UNIT
VO = ±1 9 V RL = 100 kΩ25°C 0.07 0.12
SR Slew rate at unity gainVO = ±1.9 V, CL = 100 pF
RL = 100 kΩ,Full
range0.05
V/µs
V Equivalent input noise voltagef = 10 Hz 25°C 38
nV/√HzVn Equivalent input noise voltagef = 1 kHz 25°C 19
nV/√Hz
VN(PP) Peak to peak equivalent input noise voltagef = 0.1 Hz to 1 Hz 25°C 0.8
µVVN(PP) Peak-to-peak equivalent input noise voltagef = 0.1 Hz to 10 Hz 25°C 1.1
µV
In Equivalent input noise current 25°C 0.6 fA√Hz
THD + N Total harmonic distortion pulse durationVO = ±2.3 V,f 10 kHz
AV = 125°C
0.2%THD + N Total harmonic distortion pulse duration f = 10 kHz,
RL = 50 kΩ AV = 1025°C
1%
Gain-bandwidth productf = 10 kHz,CL = 100 pF
RL = 50 kΩ,25°C 0.21 MHz
BOM Maximum output-swing bandwidthVO(PP) = 4.6 V,RL = 50 kΩ,
AV = 1,CL = 100 pF
25°C 14 kHz
φm Phase margin at unity gainRL = 50 kΩ CL = 100 pF
25°C 63°
Gain marginRL = 50 kΩ, CL = 100 pF
25°C 15 dB
† Full range is 0°C to 70°C.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER TEST CONDITIONS T †TLC2254C
UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX
UNIT
VIO Input offset voltage25°C 200 1500
µVVIO Input offset voltageFull range 1750
µV
αVIO Temperature coefficient of input offset voltage25°C
to 70°C 0.5 µV/°C
Input offset voltage long-term drift (see Note 4) VIC = 0,VO = 0
VDD± = ±2.5 V,RS = 50 Ω
25°C 0.003 µV/mo
IIO Input offset current
VO = 0, RS = 50 Ω25°C 0.5 60
pAIIO Input offset currentFull range 100
pA
IIB Input bias current25°C 1 60
pAIIB Input bias currentFull range 100
pA
VICR Common mode input voltage range RS = 50 Ω |VIO | ≤ 5 mV
25°C0to4
–0.3to
4.2VVICR Common-mode input voltage range RS = 50 Ω, |VIO | ≤ 5 mV
Full range0to
3.5
V
IOH = –20 µA 25°C 4.98
VOH High level output voltage IOH = 75 µA25°C 4.9 4.94
VVOH High-level output voltage IOH = –75 µAFull range 4.8
V
IOH = –150 µA 25°C 4.8 4.88
VIC = 2.5 V, IOL = 50 µA 25°C 0.01
VIC = 2 5 V IOL = 500 µA25°C 0.09 0.15
VIC = 2.5 V, IOL = 500 µAFull range 0.15
VOL Low-level output voltageVIC = 2 5 V IOL = 1 A
25°C 0.2 0.3 VVIC = 2.5 V, IOL = 1 A
Full range 0.3
VIC = 2 5 V IOL = 4 A25°C 0.7 1
VIC = 2.5 V, IOL = 4 AFull range 1.2
V 2 5 V R 100 kΩ‡25°C 100 350
AVD Large-signal differential voltage amplificationVIC = 2.5 V,VO = 1 V to 4 V
RL = 100 kهFull range 10 V/mVVD g g g VO = 1 V to 4 V
RL = 1 MΩ‡ 25°C 1700
ri(d) Differential input resistance 25°C 1012 Ω
ri(c) Common-mode input resistance 25°C 1012 Ω
ci(c) Common-mode input capacitance f = 10 kHz, N package 25°C 8 pF
zo Closed-loop output impedance f = 25 kHz, AV = 10 25°C 200 Ω
CMRR Common mode rejection ratioVIC = 0 to 2.7 V, VO = 2.5 V, 25°C 70 83
dBCMRR Common-mode rejection ratio IC , O ,RS = 50 Ω Full range 70
dB
kSVR Supply voltage rejection ratio (∆VDD/∆VIO)VDD = 4.4 V to 16 V, 25°C 80 95
dBkSVR Supply-voltage rejection ratio (∆VDD/∆VIO) DD ,VIC = VDD/2, No load Full range 80
dB
IDD Supply current (four amplifiers) VO = 2 5 V No load25°C 140 250
µAIDD Supply current (four amplifiers) VO = 2.5 V, No loadFull range 300
µA
† Full range is 0°C to 70°C.‡ Referenced to 2.5 VNOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
11POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER TEST CONDITIONS T †TLC2254C
UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX
UNIT
SR Slew rate at unity gainVO = 1.4 V to 2.6 V RL = 100 kΩ‡, 25°C 0.07 0.12
V/µsSR Slew rate at unity gain OCL = 100 pF‡
L ,
Full range 0.05V/µs
V Equivalent input noise voltagef = 10 Hz 25°C 36
nV/√HzVn Equivalent input noise voltagef = 1 kHz 25°C 19
nV/√Hz
VN(PP)Peak-to-peak equivalent input noise f = 0.1 Hz to 1 Hz 25°C 0.7
µVVN(PP)q
voltage f = 0.1 Hz to 10 Hz 25°C 1.1µV
In Equivalent input noise current 25°C 0.6 fA /√Hz
THD + N Total harmonic distortion plus noiseVO = 0.5 V to 2.5 V,f = 10 kHz
AV = 125°C
0.2%THD + N Total harmonic distortion plus noise f = 10 kHz,
RL = 50 kΩ‡ AV = 1025°C
1%
Gain-bandwidth productf = 10 kHz, CL = 100 pF‡
RL = 50 kΩ‡, 25°C 0.2 MHz
BOM Maximum output-swing bandwidthVO(PP) = 2 V, RL = 50 kه,
AV = 1, CL = 100 pF‡ 25°C 30 kHz
φm Phase margin at unity gainRL = 50 kΩ‡ CL = 100 pF‡ 25°C 63°
Gain marginRL = 50 kΩ‡, CL = 100 pF‡
25°C 15 dB† Full range is 0°C to 70°C.‡ Referenced to 2.5 V
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwisespecified)
PARAMETER TEST CONDITIONS T †TLC2254C
UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX
UNIT
VIO Input offset voltage25°C 200 1500
µVVIO Input offset voltageFull range 1750
µV
αVIO Temperature coefficient of input offset voltage25°C
to 70°C 0.5 µV/°C
Input offset voltage long-term drift (see Note 4) VIC = 0,RS = 50 Ω
VO = 0, 25°C 0.003 µV/mo
IIO Input offset current
RS = 50 Ω25°C 0.5 60
pAIIO Input offset currentFull range 100
pA
IIB Input bias current25°C 1 60
pAIIB Input bias currentFull range 100
pA
VICR Common mode input voltage range |VIO | ≤5 mV RS = 50 Ω
25°C–5to4
–5.3to
4.2VVICR Common-mode input voltage range |VIO | ≤5 mV, RS = 50 Ω
Full range–5to
3.5
V
IO = –20 µA 25°C 4.98
VOM Maximum positive peak output voltage IO = 100 µA25°C 4.9 4.93
VVOM+ Maximum positive peak output voltage IO = –100 µAFull range 4.7
V
IO = –200 µA 25°C 4.8 4.86
VIC = 0, IO = 50 µA 25°C –4.99
VIC = 0 IO = 500 µA25°C –4.85 –4.91
VIC = 0, IO = 500 µAFull range –4.85
VOM– Maximum negative peak output voltageVIC = 0 IO 1 A
25°C –4.7 –4.8 VVIC = 0, IO = 1 A
Full range –4.7
VIC = 0 IO 4 A25°C –4 –4.3
VIC = 0, IO = 4 AFull range –3.8
RL = 100 kΩ25°C 40 150
AVD Large-signal differential voltage amplification VO = ±4 VRL = 100 kΩ
Full range 10 V/mV
RL = 1 MΩ 25°C 3000
ri(d) Differential input resistance 25°C 1012 Ω
ri(c) Common-mode input resistance 25°C 1012 Ω
ci(c) Common-mode input capacitance f = 10 kHz, N package 25°C 8 pF
zo Closed-loop output impedance f = 25 kHz, AV = 10 25°C 190 Ω
CMRR Common mode rejection ratioVIC = –5 V to 2.7 V, 25°C 75 88
dBCMRR Common-mode rejection ratio IC ,VO = 0, RS = 50 Ω Full range 75
dB
kSVR Supply voltage rejection ratio (∆VDD± /∆VIO)VDD± = ±2.2 V to ±8 V, 25°C 80 95
dBkSVR Supply-voltage rejection ratio (∆VDD± /∆VIO) DD± ,VIC = 0, No load Full range 80
dB
IDD Supply current (four amplifiers) VO = 0 No load25°C 160 250
µAIDD Supply current (four amplifiers) VO = 0, No loadFull range 300
µA
† Full range is 0°C to 70°C.NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
13POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER TEST CONDITIONS T †TLC2254C
UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX
UNIT
SR Slew rate at unity gainVO = ±1.9 V, RL = 100 kΩ, 25°C 0.07 0.12
V/µsSR Slew rate at unity gain O ,CL = 100 pF
L ,
Full range 0.05V/µs
V Equivalent input noise voltagef = 10 Hz 25°C 38
nV/√HzVn Equivalent input noise voltagef = 1 kHz 25°C 19
nV/√Hz
VN(PP) Peak to peak equivalent input noise voltagef = 0.1 Hz to 1 Hz 25°C 0.8
µVVN(PP) Peak-to-peak equivalent input noise voltagef = 0.1 Hz to 10 Hz 25°C 1.1
µV
In Equivalent input noise current 25°C 0.6 fA /√Hz
THD + N Total harmonic distortion plus noiseVO = ± 2.3 V,f 20 kHz
AV = 125°C
0.2%THD + N Total harmonic distortion plus noise f = 20 kHz,
RL = 50 kΩ AV = 1025°C
1%
Gain-bandwidth productf = 10 kHz,CL = 100 pF
RL = 50 kΩ,25°C 0.21 MHz
BOM Maximum output-swing bandwidthVO(PP) = 4.6 V,RL = 50 kΩ,
AV = 1,CL = 100 pF
25°C 14 kHz
φm Phase margin at unity gainRL = 50 kΩ CL = 100 pF
25°C 63°
Gain marginRL = 50 kΩ, CL = 100 pF
25°C 15 dB† Full range is 0°C to 70°C.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER TEST CONDITIONS T †TLC2252I TLC2252AI
UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX MIN TYP MAX
UNIT
VIO Input offset voltage
V V V
25°C 200 1500 200 850µVVIO Input offset voltage
V V V
Full range 1750 1000µV
αVIOTemperature coefficientof input offset voltage
V V V
25°Cto 85°C 0.5 0.5 µV/°C
Input offset voltagelong-term drift(see Note 4)
VDD± = ±2.5 V, VO = 0,VIC = 0, RS = 50 Ω 25°C 0.003 0.003 µV/mo
IIO Input offset current25°C 0.5 60 0.5 60
pAIIO Input offset currentFull range 1000 1000
pA
IIB Input bias current25°C 1 60 1 60
pAIIB Input bias currentFull range 1000 1000
pA
VICRCommon-mode input
RS = 50 Ω |VIO | ≤5 mV
25°C0to4
–0.3to
4.2
0to4
–0.3to
4.2VVICR voltage range RS = 50 Ω, |VIO | ≤5 mV
Full range0to
3.5
0to
3.5
V
IOH = –20 µA 25°C 4.98 4.98
VOHHigh-level output
IOH = 75 µA25°C 4.9 4.94 4.9 4.94
VVOHg
voltage IOH = –75 µAFull range 4.8 4.8
V
IOH = –150 µA 25°C 4.8 4.88 4.8 4.88
VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01
Low level output VIC = 2 5 V IOL = 500 µA25°C 0.09 0.15 0.09 0.15
VOLLow-level outputvoltage
VIC = 2.5 V, IOL = 500 µAFull range 0.15 0.15 V
voltage
VIC = 2 5 V IOL = 4 A25°C 0.8 1 0.7 1
VIC = 2.5 V, IOL = 4 AFull range 1.2 1.2
Large signal differential V 2 5 V RL 100 kΩ‡25°C 100 350 100 350
AVDLarge-signal differentialvoltage amplification
VIC = 2.5 V,VO = 1 V to 4 V
RL = 100 kهFull range 10 10 V/mVVD voltage am lification VO = 1 V to 4 V
RL = 1 MΩ‡ 25°C 1700 1700
ridDifferential inputresistance
25°C 1012 1012 Ω
ricCommon-mode input resistance
25°C 1012 1012 Ω
cicCommon-mode input capacitance
f = 10 kHz, P package 25°C 8 8 pF
zoClosed-loopoutput impedance
f = 25 kHz, AV = 10 25°C 200 200 Ω
CMRRCommon-mode VIC = 0 to 2.7 V, VO = 2.5 V, 25°C 70 83 70 83
dBCMRR rejection ratioIC , O ,
RS = 50 Ω Full range 70 70dB
kSVR
Supply-voltage rejection ratio
VDD = 4.4 V to 16 V, 25°C 80 95 80 95dBkSVR rejection ratio
(∆VDD/∆VIO)
DDVIC = VDD/2, No load Full range 80 80
dB
IDD Supply current VO = 2 5 V No load25°C 70 125 70 125
µAIDD Su ly current VO = 2.5 V, No loadFull range 150 150
µA
† Full range is – 40°C to 125°C.‡ Referenced to 2.5 VNOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
15POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER TEST CONDITIONS T †TLC2252I TLC2252AI
UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX MIN TYP MAX
UNIT
Slew rate at unityVO = 1.5 V to 3.5 V, RL = 100 kΩ‡, 25°C 0.07 0.12 0.07 0.12
SRSlew rate at unitygain
O , L ,CL = 100 pF‡ Full
range0.05 0.05
V/µs
VEquivalent input f = 10 Hz 25°C 36 36
nV/√HzVnq
noise voltage f = 1 kHz 25°C 19 19nV/√Hz
VN(PP)
Peak-to-peakequivalent input
f = 0.1 Hz to 1 Hz 25°C 0.7 0.7µVVN(PP) equivalent input
noise voltage f = 0.1 Hz to 10 Hz 25°C 1.1 1.1µV
InEquivalent inputnoise current
25°C 0.6 0.6 fA√Hz
THD + NTotal harmonicdistortion plus
VO = 0.5 V to 2.5 V,f 10 kHz
AV = 125°C
0.2% 0.2%THD + N distortion plus
noisef = 10 kHz,RL = 50 kه AV = 10
25°C1% 1%
Gain-bandwidthproduct
f = 50 kHz,CL = 100 pF‡
RL = 50 kΩ‡, 25°C 0.2 0.2 MHz
BOMMaximum output-swing bandwidth
VO(PP) = 2 V, RL = 50 kه,
AV = 1,RL = 50 kه,
25°C 30 30 kHz
φmPhase margin atunity gain RL = 50 kΩ‡, CL = 100 pF‡
25°C 63° 63°
Gain marginL , L
25°C 15 15 dB† Full range is – 40°C to 125°C.‡ Referenced to 2.5 V
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
16 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwise noted)
PARAMETER TEST CONDITIONS T †TLC2252I TLC2252AI
UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX MIN TYP MAX
UNIT
VIO Input offset voltage
V V
25°C 200 1500 200 850µVVIO Input offset voltage
V V
Full range 1750 1000µV
αVIOTemperature coefficient ofinput offset voltage
V V
25°Cto 85°C 0.5 0.5 µV/°C
Input offset voltage long-term drift (see Note 4)
VIC = 0, VO = 0,RS = 50 Ω
25°C 0.003 0.003 µV/mo
IIO Input offset current
S25°C 0.5 60 0.5 60
pAIIO Input offset currentFull range 1000 1000
pA
IIB Input bias current25°C 1 60 1 60
pAIIB Input bias currentFull range 1000 1000
pA
VICRCommon-mode input
RS = 50 Ω |VIO | ≤5 mV
25°C–5to4
–5.3to
4.2
–5to4
–5.3to
4.2VVICR voltage range
RS = 50 Ω, |VIO | ≤5 mV
Full range–5to
3.5
–5to
3.5
V
IO = –20 µA 25°C 4.98 4.98
VOMMaximum positive peak
IO = 100 µA25°C 4.9 4.93 4.9 4.93
VVOM+ output voltageIO = –100 µA
Full range 4.7 4.7V
IO = –200 µA 25°C 4.8 4.86 4.8 4.86
VIC = 0, IO = 50 µA 25°C –4.99 –4.99
M i ti VIC = 0 IO = 500 µA25°C –4.85 –4.91 –4.85 –4.91
VOM–Maximum negativepeak output voltage
VIC = 0, IO = 500 µAFull range –4.85 –4.85 V
eak out ut voltage
VIC = 0 IO = 4 A25°C –4 –4.3 –4 –4.3
VIC = 0, IO = 4 AFull range –3.8 –3.8
L i l diff ti l RL = 50 kΩ25°C 40 150 40 150
AVDLarge-signal differentialvoltage amplification
VO = ±4 VRL = 50 kΩ
Full range 10 10 V/mVvoltage am lification
RL = 1 MΩ 25°C 3000 3000
ridDifferential inputresistance
25°C 1012 1012 Ω
ricCommon-mode inputresistance
25°C 1012 1012 Ω
cicCommon-mode inputcapacitance
f = 10 kHz, P package 25°C 8 8 pF
zoClosed-loop output impedance
f = 25 kHz, AV = 10 25°C 190 190 Ω
CMRRCommon-mode VIC = –5 V to 2.7 V, 25°C 75 88 75 88
dBCMRRrejection ratio
IC ,VO = 0, RS = 50 Ω Full range 75 75
dB
kSVRSupply-voltage rejection VDD = 4.4 V to 16 V, 25°C 80 95 80 95
dBkSVRy g j
ratio (∆VDD± /∆VIO)DD ,
VIC = VDD/2, No load Full range 80 80dB
IDD Supply current VO = 2 5 V No load25°C 80 125 80 125
µAIDD Supply current VO = 2.5 V, No loadFull range 150 150
µA
† Full range is – 40°C to 125°C.NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
17POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER TEST CONDITIONS T †TLC2252I TLC2252AI
UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX MIN TYP MAX
UNIT
VO = ±1 9 V RL = 100 kΩ25°C 0.07 0.12 0.07 0.12
SR Slew rate at unity gainVO = ±1.9 V, RL = 100 kΩ,CL = 100 pF Full
range0.05 0.05
V/µs
VEquivalent input noise f = 10 Hz 25°C 38 38
nV/√HzVnq
voltage f = 1 kHz 25°C 19 19nV/√Hz
VN(PP)Peak-to-peak equivalent f = 0.1 Hz to 1 Hz 25°C 0.8 0.8
µVVN(PP)q
input noise voltage f = 0.1 Hz to 10 Hz 25°C 1.1 1.1µV
InEquivalent input noisecurrent
25°C 0.6 0.6 fA√Hz
THD + NTotal harmonic distortion
VO = ±2.3 V,RL 50 kΩ
AV = 125°C
0.2% 0.2%THD + N
plus noiseRL = 50 kΩ,f = 10 kHz AV = 10
25°C1% 1%
Gain-bandwidth productf =10 kHz, RL = 50 kΩ,CL = 100 pF
25°C 0.21 0.21 MHz
BOMMaximum output-swingbandwidth
VO(PP) = 4.6 V, AV = 1,RL = 50 kΩ, CL = 100 pF
25°C 14 14 kHz
φmPhase margin at unitygain RL = 50 kΩ, CL = 100 pF
25°C 63° 63°
Gain marginL L
25°C 15 15 dB
† Full range is –40°C to 125°C.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
18 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER TEST CONDITIONS T †TLC2254I TLC2254AI
UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX MIN TYP MAX
UNIT
VIO Input offset voltage25°C 200 1500 200 850
µVVIO In ut offset voltageFull range 1750 1000
µV
αVIO
Temperaturecoefficient of inputoffset voltage VDD± = ±2.5 V,
25°Cto 125°C 0.5 0.5 µV/°C
Input offset voltagelong-term drift(see Note 4)
VDD± = ±2.5 V,VIC = 0,VO = 0,RS = 50 Ω
25°C 0.003 0.003 µV/mo
IIO Input offset current
S25°C 0.5 60 0.5 60
pAIIO In ut offset currentFull range 1000 1000
A
IIB Input bias current25°C 1 60 1 60
pAIIB In ut bias currentFull range 1000 1000
A
VICRCommon-mode input
RS = 50 Ω |VIO | ≤5 mV
25°C0to4
–0.3to
4.2
0to4
–0.3to
4.2VVICR voltage range
RS = 50 Ω, |VIO | ≤5 mV
Full range0to
3.5
0to
3.5
V
IOH = –20 µA 25°C 4.98 4.98
VOHHigh-level output
IOH = –75 µA25°C 4.9 4.94 4.9 4.94
VVOHg
voltageIOH = –75 µA
Full range 4.8 4.8V
IOH = –150 µA 25°C 4.8 4.88 4.8 4.88
VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01
Low level output VIC = 2 5 V IOL = 500 µA25°C 0.09 0.15 0.09 0.15
VOLLow-level outputvoltage
VIC = 2.5 V, IOL = 500 µAFull range 0.15 0.15 Vvoltage
VIC = 2 5 V IOL = 4 A25°C 0.8 1 0.7 1
VIC = 2.5 V, IOL = 4 AFull range 1.2 1.2
Large-signalV 2 5 V RL 100 kه
25°C 100 350 100 350
AVD
Large signaldifferential
VIC = 2.5 V,VO = 1 V to 4 V
RL = 100 kهFull range 10 10 V/mV
voltage amplificationVO = 1 V to 4 V
RL = 1 MΩ‡ 25°C 1700 1700
ri(d)Differential inputresistance
25°C 1012 1012 Ω
ri(c)Common-mode inputresistance
25°C 1012 1012 Ω
ci(c)Common-mode inputcapacitance
f = 10 kHz, N package 25°C 8 8 pF
zoClosed-loop outputimpedance
f = 25 kHz, AV = 10 25°C 200 200 Ω
CMRRCommon-mode VIC = 0 to 2.7 V, VO = 2.5 V, 25°C 70 83 70 83
dBCMRRrejection ratio
IC ORS = 50 Ω Full range 70 70
dB
kSVR
Supply-voltagerejection ratio
VDD = 4.4 V to 16 V, 25°C 80 95 80 95dBkSVR rejection ratio
(∆VDD/∆VIO)
DDVIC = VDD/2, No load Full range 80 80
dB
IDDSupply current
VO = 2 5 V No load25°C 140 250 140 250
µAIDDy
(four amplifiers)VO = 2.5 V, No load
Full range 300 300µA
† Full range is – 40°C to 125°C.‡ Referenced to 2.5 VNOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
19POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER TEST CONDITIONS T †TLC2254I TLC2254AI
UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX MIN TYP MAX
UNIT
Slew rate at unityVO = 1.4 V to 2.6 V, 25°C 0.07 0.12 0.07 0.12
SRSlew rate at unitygain
O ,RL = 100 kΩ‡,CL = 100 pF‡
Fullrange
0.05 0.05V/µs
VEquivalent input f = 10 Hz 25°C 36 36
nV/√HzVnq
noise voltage f = 1 kHz 25°C 19 19nV/√Hz
VN(PP)
Peak-to-peakequivalent input
f = 0.1 Hz to 1 Hz 25°C 0.7 0.7µVVN(PP) equivalent input
noise voltage f = 0.1 Hz to 10 Hz 25°C 1.1 1.1µV
InEquivalent inputnoise current
25°C 0.6 0.6 fA /√Hz
THD + NTotal harmonicdistortion plus
VO = 0.5 V to 2.5 V,f 20 kHz
AV = 125°C
0.2% 0.2%THD + N distortion plus
noisef = 20 kHz,RL = 50 kه AV = 10
25°C1% 1%
Gain-bandwidthproduct
f = 50 kHz,CL = 100 pF‡
RL = 50 kΩ‡, 25°C 0.2 0.2 MHz
BOMMaximum output-swing bandwidth
VO(PP) = 2 V,RL = 50 kه,
AV = 1,CL = 100 pF‡ 25°C 30 30 kHz
φmPhase margin atunity gain RL = 50 kΩ‡, CL = 100 pF‡
25°C 63° 63°
Gain marginL , L
25°C 15 15 dB† Full range is – 40°C to 125°C.‡ Referenced to 2.5 V
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
20 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwise noted)
PARAMETER TEST CONDITIONS T †TLC2254I TLC2254AI
UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX MIN TYP MAX
UNIT
VIO Input offset voltage25°C 200 1500 200 850
µVVIO Input offset voltageFull range 1750 1000
µV
αVIOTemperature coefficient ofinput offset voltage
25°Cto 125°C 0.5 0.5 µV/°C
Input offset voltagelong-term drift (see Note 4)
VIC = 0,RS = 50 Ω
VO = 0, 25°C 0.003 0.003 µV/mo
IIO Input offset current
S25°C 0.5 60 0.5 60
pAIIO Input offset currentFull range 1000 1000
pA
IIB Input bias current25°C 1 60 1 60
pAIIB Input bias currentFull range 1000 1000
pA
VICRCommon-mode input
RS = 50 Ω |VIO | ≤5 mV
25°C–5to4
–5.3to
4.2
–5to4
–5.3to
4.2VVICR voltage range
RS = 50 Ω, |VIO | ≤5 mV
Full range–5to
3.5
–5to
3.5
V
IO = –20 µA 25°C 4.98 4.98
VOMMaximum positive peak
IO = 100 µA25°C 4.9 4.93 4.9 4.93
VVOM+ output voltageIO = –100 µA
Full range 4.7 4.7V
IO = –200 µA 25°C 4.8 4.86 4.8 4.86
VIC = 0, IO = 50 µA 25°C –4.99 –4.99
M i ti k VIC = 0 IO = 500 µA25°C –4.85 –4.91 –4.85 –4.91
VOM–Maximum negative peakoutput voltage
VIC = 0, IO = 500 µAFull range –4.85 –4.85 V
out ut voltage
VIC = 0 IO = 4 A25°C –4 –4.3 –4 –4.3
VIC = 0, IO = 4 AFull range –3.8 –3.8
L i l diff ti l RL = 100 kΩ25°C 40 150 40 150
AVDLarge-signal differentialvoltage amplification
VO = ±4 VRL = 100 kΩ
Full range 10 10 V/mVvoltage am lification
RL = 1 MΩ 25°C 3000 3000
ri(d) Differential input resistance 25°C 1012 1012 Ω
ri(c)Common-mode inputresistance
25°C 1012 1012 Ω
ci(c)Common-mode inputcapacitance
f = 10 kHz, N package 25°C 8 8 pF
zoClosed-loop outputimpedance
f = 25 kHz, AV = 10 25°C 190 190 Ω
CMRRCommon-mode rejection VIC = –5 V to 2.7 V, 25°C 75 88 75 88
dBCMRRj
ratioIC ,
VO = 0, RS = 50 Ω Full range 75 75dB
kSVRSupply-voltage rejection VDD± = ±2.2 V to ±8 V, 25°C 80 95 80 95
dBkSVRy g j
ratio (∆VDD± /∆VIO)DD± ,
VIC = VDD/2, No load Full range 80 80dB
IDDSupply current
VO = 0 No load25°C 160 250 160 250
µAIDDy
(four amplifiers)VO = 0, No load
Full range 300 300µA
† Full range is – 40°C to 125°C.NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
21POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER TEST CONDITIONS T †TLC2254I TLC2254AI
UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX MIN TYP MAX
UNIT
VO = ±1 9 V RL = 100 kΩ25°C 0.07 0.12 0.07 0.12
SR Slew rate at unity gainVO = ±1.9 V,CL = 100 pF
RL = 100 kΩ,Full
range0.05 0.05
V/µs
VEquivalent input noise f = 10 Hz 25°C 38 38
nV/√HzVnq
voltage f = 1 kHz 25°C 19 19nV/√Hz
VN(PP)
Peak-to-peakequivalent input noise
f = 0.1 Hz to 1 Hz 25°C 0.8 0.8µVVN(PP) equivalent input noise
voltage f = 0.1 Hz to 10 Hz 25°C 1.1 1.1µV
InEquivalent input noisecurrent
25°C 0.6 0.6 fA /√Hz
THD + NTotal harmonic
VO = ±2.3 V,RL 50 kΩ
AV = 125°C
0.2% 0.2%THD + N
distortion plus noiseRL = 50 kΩ,f = 20 kHz AV = 10
25°C1% 1%
Gain-bandwidth productf =10 kHz,CL = 100 pF
RL = 50 kΩ,25°C 0.21 0.21 MHz
BOMMaximum output-swingbandwidth
VO(PP) = 4.6 V,RL = 50 kΩ,
AV = 1,CL = 100 pF
25°C 14 14 kHz
φmPhase margin at unitygain RL = 50 kΩ, CL = 100 pF
25°C 63° 63°
Gain marginL L
25°C 15 15 dB† Full range is –40°C to 125°C.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
22 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER TEST CONDITIONS TA†TLC2252QTLC2252M
TLC2252AQTLC2252AM UNITA
MIN TYP MAX MIN TYP MAX
VIO Input offset voltage
V V V
25°C 200 1500 200 850µVVIO Input offset voltage
V V V
Full range 1750 1000µV
αVIOTemperature coefficientof input offset voltage
V V V
25°Cto 125°C 0.5 0.5 µV/°C
Input offset voltagelong-term drift(see Note 4)
VDD± = ±2.5 V,VO = 0,
VIC = 0,RS = 50 Ω 25°C 0.003 0.003 µV/mo
IIO Input offset current25°C 0.5 60 0.5 60
pAIIO Input offset currentFull range 1000 1000
pA
IIB Input bias current25°C 1 60 1 60
pAIIB Input bias currentFull range 1000 1000
pA
VICRCommon-mode input
RS = 50 Ω |VIO | ≤5 mV
25°C0to4
–0.3to
4.2
0to4
–0.3to
4.2VVICR voltage range RS = 50 Ω, |VIO | ≤5 mV
Full range0to
3.5
0to
3.5
V
IOH = –20 µA 25°C 4.98 4.98
VOHHigh-level output
IOH = 75 µA25°C 4.9 4.94 4.9 4.94
VVOHg
voltage IOH = –75 µAFull range 4.8 4.8
V
IOH = –150 µA 25°C 4.8 4.88 4.8 4.88
VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01
Low level output VIC = 2 5 V IOL = 500 µA25°C 0.09 0.15 0.09 0.15
VOLLow-level outputvoltage
VIC = 2.5 V, IOL = 500 µAFull range 0.15 0.15 V
voltage
VIC = 2 5 V IOL = 4 A25°C 0.8 1 0.7 1
VIC = 2.5 V, IOL = 4 AFull range 1.2 1.2
Large signal differential V 2 5 V RL 100 kΩ‡25°C 100 350 100 350
AVDLarge-signal differentialvoltage amplification
VIC = 2.5 V,VO = 1 V to 4 V
RL = 100 kهFull range 10 10 V/mVVD voltage am lification VO = 1 V to 4 V
RL = 1 MΩ‡ 25°C 1700 1700
ridDifferential input resistance
25°C 1012 1012 Ω
ricCommon-mode inputresistance
25°C 1012 1012 Ω
cicCommon-mode inputcapacitance
f = 10 kHz, f = 10 kHz, 25°C 8 8 pF
zoClosed-loop output impedance
f = 25 kHz, AV = 10 25°C 200 200 Ω
CMRRCommon-mode VIC = 0 to 2.7 V, VO = 2.5 V, 25°C 70 83 70 83
dBCMRR rejection ratioIC ,
RS = 50 ΩO ,
Full range 70 70dB
kSVR
Supply-voltage rejection ratio
VDD = 4.4 V to 16 V, 25°C 80 95 80 95dBkSVR rejection ratio
(∆VDD/∆VIO)
DDVIC = VDD/2, No load Full range 80 80
dB
IDD Supply current VO = 2 5 V No load25°C 70 125 70 125
µAIDD Su ly current VO = 2.5 V, No loadFull range 150 150
µA
† Full range is – 40°C to 125°C for Q suffix, – 55°C to 125°C for M suffix.‡ Referenced to 2.5 VNOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
23POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER TEST CONDITIONS TA†TLC2252QTLC2252M
TLC2252AQTLC2252AM UNITA
MIN TYP MAX MIN TYP MAX
Slew rate at unity VO = 0 5 V to 3 5 V25°C 0.07 0.12 0.07 0.12
SRSlew rate at unitygain
VO = 0.5 V to 3.5 V,RL = 100 kΩ‡, CL = 100 pF‡ Full
range0.05 0.05
V/µs
VEquivalent input f = 10 Hz 25°C 36 36
nV/√HzVnq
noise voltage f = 1 kHz 25°C 19 19nV/√Hz
VN(PP)
Peak-to-peakequivalent input
f = 0.1 Hz to 1 Hz 25°C 0.7 0.7µVVN(PP) equivalent input
noise voltage f = 0.1 Hz to 10 Hz 25°C 1.1 1.1µV
InEquivalent inputnoise current
25°C 0.6 0.6 fA√Hz
THD + NTotal harmonicdistortion plus
VO = 0.5 V to 2.5 V,f 10 kHz
AV = 125°C
0.2% 0.2%THD + N distortion plus
noisef = 10 kHz,RL = 50 kه AV = 10
25°C1% 1%
Gain-bandwidthproduct
f = 50 kHz, RL = 50 kΩ‡,CL = 100 pF‡ 25°C 0.2 0.2 MHz
BOMMaximum output-swing bandwidth
VO(PP) = 2 V, AV = 1,RL = 50 kΩ‡, CL = 100 pF‡ 25°C 30 30 kHz
φmPhase margin atunity gain RL = 50 kΩ‡, CL = 100 pF‡
25°C 63° 63°
Gain marginL , L
25°C 15 15 dB† Full range is – 40°C to 125°C for Q suffix, – 55°C to 125°C for M suffix.‡ Referenced to 2.5 V
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
24 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwise noted)
PARAMETER TEST CONDITIONS TA†TLC2252QTLC2252M
TLC2252AQTLC2252AM UNITA
MIN TYP MAX MIN TYP MAX
VIO Input offset voltage
V V
25°C 200 1500 200 850µVVIO Input offset voltage
V V
Full range 1750 1000µV
αVIOTemperature coefficient ofinput offset voltage
V V
25°Cto 125°C 0.5 0.5 µV/°C
Input offset voltage long-term drift (see Note 4)
VIC = 0, VO = 0,RS = 50 Ω
25°C 0.003 0.003 µV/mo
IIO Input offset current
S25°C 0.5 60 0.5 60
pAIIO Input offset currentFull range 1000 1000
pA
IIB Input bias current25°C 1 60 1 60
pAIIB Input bias currentFull range 1000 1000
pA
VICRCommon-mode input
RS = 50 Ω |VIO | ≤5 mV
25°C–5to4
–5.3to
4.2
–5to4
–5.3to
4.2VVICR voltage range
RS = 50 Ω, |VIO | ≤5 mV
Full range–5to
3.5
–5to
3.5
V
IO = –20 µA 25°C 4.98 4.98
VOMMaximum positive peak
IO = 100 µA25°C 4.9 4.93 4.9 4.93
VVOM+ output voltageIO = –100 µA
Full range 4.7 4.7V
IO = –200 µA 25°C 4.8 4.86 4.8 4.86
VIC = 0, IO = 50 µA 25°C –4.99 –4.99
M i ti VIC = 0 IO = 500 µA25°C –4.85 –4.91 –4.85 –4.91
VOM–Maximum negativepeak output voltage
VIC = 0, IO = 500 µAFull range –4.85 –4.85 V
eak out ut voltage
VIC = 0 IO = 4 A25°C –4 –4.3 –4 –4.3
VIC = 0, IO = 4 AFull range –3.8 –3.8
L i l diff ti l RL = 100 kΩ25°C 40 150 40 150
AVDLarge-signal differentialvoltage amplification
VO = ±4 VRL = 100 kΩ
Full range 10 10 V/mVvoltage am lification
RL = 1 MΩ 25°C 3000 3000
ridDifferential inputresistance
25°C 1012 1012 Ω
ricCommon-mode inputresistance
25°C 1012 1012 Ω
cicCommon-mode inputcapacitance
f = 10 kHz, P package 25°C 8 8 pF
zoClosed-loop output impedance
f = 25 kHz, AV = 10 25°C 190 190 Ω
CMRRCommon-mode VIC = –5 V to 2.7 V, 25°C 75 88 75 88
dBCMRRrejection ratio
IC ,VO = 0, RS = 50 Ω Full range 75 75
dB
kSVRSupply-voltage rejection VDD = ±2.2 V to ±8 V, 25°C 80 95 80 95
dBkSVRy g j
ratio (∆VDD± /∆VIO)DD ,
VIC = 0, No load Full range 80 80dB
IDD Supply current VO = 2 5 V No load25°C 80 125 80 125
µAIDD Supply current VO = 2.5 V, No loadFull range 150 150
µA
† Full range is – 40°C to 125°C for Q suffix, – 55°C to 125°C for M suffix.NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
25POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER TEST CONDITIONS TA†TLC2252QTLC2252M
TLC2252AQTLC2252AM UNITA
MIN TYP MAX MIN TYP MAX
VO = ±2 V RL = 100 kΩ25°C 0.07 0.12 0.07 0.12
SR Slew rate at unity gainVO = ±2 V, RL = 100 kΩ,CL = 100 pF Full
range0.05 0.05
V/µs
VEquivalent input noise f = 10 Hz 25°C 38 38
nV/√HzVnq
voltage f = 1 kHz 25°C 19 19nV/√Hz
VN(PP)Peak-to-peak equivalent f = 0.1 Hz to 1 Hz 25°C 0.8 0.8
µVVN(PP)q
input noise voltage f = 0.1 Hz to 10 Hz 25°C 1.1 1.1µV
InEquivalent input noisecurrent
25°C 0.6 0.6 fA√Hz
THD + NTotal harmonic distortion
VO = ±2.3 V,RL 50 kΩ
AV = 125°C
0.2% 0.2%THD + N
plus noiseRL = 50 kΩ,f = 10 kHz AV = 10
25°C1% 1%
Gain-bandwidth productf =10 kHz, RL = 50 kΩ,CL = 100 pF
25°C 0.21 0.21 MHz
BOMMaximum output-swingbandwidth
VO(PP) = 4.6 V, AV = 1,RL = 50 kΩ, CL = 100 pF
25°C 14 14 kHz
φmPhase margin at unitygain RL = 50 kΩ, CL = 100 pF
25°C 63° 63°
Gain marginL L
25°C 15 15 dB† Full range is – 40°C to 125°C for Q suffix, – 55°C to 125°C for M suffix.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
26 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER TEST CONDITIONS TA†TLC2254QTLC2254M
TLC2254AQTLC2254AM UNITA
MIN TYP MAX MIN TYP MAX
VIO Input offset voltage25°C 200 1500 200 850
µVVIO In ut offset voltageFull range 1750 1000
µV
αVIO
Temperaturecoefficient of inputoffset voltage
25°Cto 125°C 0.5 0.5 µV/°C
Input offset voltagelong-term drift(see Note 4)
VDD± = ±2.5 V,VO = 0,
VIC = 0,RS = 50 Ω 25°C 0.003 0.003 µV/mo
IIO Input offset current25°C 0.5 60 0.5 60
pAIIO In ut offset current125°C 1000 1000
A
IIB Input bias current25°C 1 60 1 60
pAIIB In ut bias current125°C 1000 1000
A
VICRCommon-mode input
RS = 50 Ω |VIO | ≤5 mV
25°C0to4
–0.3to
4.2
0to4
–0.3to
4.2VVICR voltage range
RS = 50 Ω, |VIO | ≤5 mV
Full range0to
3.5
0to
3.5
V
IOH = –20 µA 25°C 4.98 4.98
VOHHigh-level output
IOH = –75 µA25°C 4.9 4.94 4.9 4.94
VVOHg
voltageIOH = –75 µA
Full range 4.8 4.8V
IOH = –150 µA 25°C 4.8 4.88 4.8 4.88
VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01
Low level output VIC = 2 5 V IOL = 500 µA25°C 0.09 0.15 0.09 0.15
VOLLow-level outputvoltage
VIC = 2.5 V, IOL = 500 µAFull range 0.15 0.15 Vvoltage
VIC = 2 5 V IOL = 4 A25°C 0.8 1 0.7 1
VIC = 2.5 V, IOL = 4 AFull range 1.2 1.2
Large-signalV 2 5 V RL 100 kه
25°C 100 350 100 350
AVD
Large signaldifferential
VIC = 2.5 V,VO = 1 V to 4 V
RL = 100 kهFull range 10 10 V/mV
voltage amplificationVO = 1 V to 4 V
RL = 1 MΩ‡ 25°C 1700 1700
ri(d)Differential inputresistance
25°C 1012 1012 Ω
ri(c)Common-mode inputresistance
25°C 1012 1012 Ω
ci(c)Common-mode inputcapacitance
f = 10 kHz, N package 25°C 8 8 pF
zoClosed-loop outputimpedance
f = 25 kHz, AV = 10 25°C 200 200 Ω
CMRRCommon-mode VIC = 0 to 2.7 V, VO = 2.5 V, 25°C 70 83 70 83
dBCMRRrejection ratio
IC ORS = 50 Ω Full range 70 70
dB
kSVR
Supply-voltagerejection ratio
VDD = 4.4 V to 16 V, 25°C 80 95 80 95dBkSVR rejection ratio
(∆VDD/∆VIO)
DDVIC = VDD/2, No load Full range 80 80
dB
IDDSupply current
VO = 2 5 V No load25°C 140 250 140 250
µAIDDy
(four amplifiers)VO = 2.5 V, No load
Full range 300 300µA
† Full range is – 40°C to 125°C for Q suffix, – 55°C to 125°C for M suffix.‡ Referenced to 2.5 VNOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
27POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER TEST CONDITIONS TA†TLC2254QTLC2254M
TLC2254AQTLC2254AM UNITA
MIN TYP MAX MIN TYP MAX
Slew rate at unityVO = 0.5 V to 3.5 V, 25°C 0.07 0.12 0.07 0.12
SRSlew rate at unitygain
O ,RL = 100 kΩ‡,CL = 100 pF‡
Fullrange
0.05 0.05V/µs
VEquivalent input f = 10 Hz 25°C 36 36
nV/√HzVnq
noise voltage f = 1 kHz 25°C 19 19nV/√Hz
VN(PP)
Peak-to-peakequivalent input
f = 0.1 Hz to 1 Hz 25°C 0.7 0.7µVVN(PP) equivalent input
noise voltage f = 0.1 Hz to 10 Hz 25°C 1.1 1.1µV
InEquivalent inputnoise current
25°C 0.6 0.6 fA /√Hz
THD + NTotal harmonicdistortion plus
VO = 0.5 V to 2.5 V,f 20 kHz
AV = 125°C
0.2% 0.2%THD + N distortion plus
noisef = 20 kHz,RL = 50 kه AV = 10
25°C1% 1%
Gain-bandwidthproduct
f = 50 kHz,CL = 100 pF‡
RL = 50 kΩ‡, 25°C 0.2 0.2 MHz
BOMMaximum output-swing bandwidth
VO(PP) = 2 V,RL = 50 kه,
AV = 1,CL = 100 pF‡ 25°C 30 30 kHz
φmPhase margin atunity gain RL = 50 kΩ‡, CL = 100 pF‡
25°C 63° 63°
Gain marginL , L
25°C 15 15 dB† Full range is – 40°C to 125°C for Q suffix, – 55°C to 125°C for M suffix.‡ Referenced to 2.5 V
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
28 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwise noted)
PARAMETER TEST CONDITIONS TA†TLC2254QTLC2254M
TLC2254AQTLC2254AM UNITA
MIN TYP MAX MIN TYP MAX
VIO Input offset voltage25°C 200 1500 200 850
µVVIO Input offset voltageFull range 1750 1000
µV
αVIOTemperature coefficient ofinput offset voltage
25°Cto 125°C 0.5 0.5 µV/°C
Input offset voltagelong-term drift (see Note 4)
VIC = 0,RS = 50 Ω
VO = 0, 25°C 0.003 0.003 µV/mo
IIO Input offset current
S25°C 0.5 60 0.5 60
pAIIO Input offset current125°C 1000 1000
pA
IIB Input bias current25°C 1 60 1 60
pAIIB Input bias current125°C 1000 1000
pA
VICRCommon-mode input
RS = 50 Ω |VIO | ≤5 mV
25°C–5to4
–5.3to
4.2
–5to4
–5.3to
4.2VVICR voltage range
RS = 50 Ω, |VIO | ≤5 mV
Full range–5to
3.5
–5to
3.5
V
IO = –20 µA 25°C 4.98 4.98
VOMMaximum positive peak
IO = 100 µA25°C 4.9 4.93 4.9 4.93
VVOM+ output voltageIO = –100 µA
Full range 4.7 4.7V
IO = –200 µA 25°C 4.8 4.86 4.8 4.86
VIC = 0, IO = 50 µA 25°C –4.99 –4.99
M i ti k VIC = 0 IO = 500 µA25°C –4.85 –4.91 –4.85 –4.91
VOM–Maximum negative peakoutput voltage
VIC = 0, IO = 500 µAFull range –4.85 –4.85 V
out ut voltage
VIC = 0 IO = 4 A25°C –4 –4.3 –4 –4.3
VIC = 0, IO = 4 AFull range –3.8 –3.8
L i l diff ti l RL = 100 kΩ25°C 40 150 40 150
AVDLarge-signal differentialvoltage amplification
VO = ±4 VRL = 100 kΩ
Full range 10 10 V/mVvoltage am lification
RL = 1 MΩ 25°C 3000 3000
ri(d) Differential input resistance 25°C 1012 1012 Ω
ri(c)Common-mode inputresistance
25°C 1012 1012 Ω
ci(c)Common-mode inputcapacitance
f = 10 kHz, N package 25°C 8 8 pF
zoClosed-loop outputimpedance
f = 25 kHz, AV = 10 25°C 190 190 Ω
CMRRCommon-mode rejection VIC = –5 V to 2.7 V, 25°C 75 88 75 88
dBCMRRj
ratioIC ,
VO = 0, RS = 50 Ω Full range 75 75dB
kSVRSupply-voltage rejection VDD± = ±2.2 V to ±8 V, 25°C 80 95 80 95
dBkSVRy g j
ratio (∆VDD± /∆VIO)DD± ,
VIC = VDD/2, No load Full range 80 80dB
IDDSupply current
VO = 0 No load25°C 160 250 160 250
µAIDDy
(four amplifiers)VO = 0, No load
Full range 300 300µA
† Full range is – 40°C to 125°C for Q suffix, – 55°C to 125°C for M suffix.NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
29POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER TEST CONDITIONS TA†TLC2254QTLC2254M
TLC2254AQTLC2254AM UNITA
MIN TYP MAX MIN TYP MAX
VO = ±2 V RL = 100 kΩ25°C 0.07 0.12 0.07 0.12
SR Slew rate at unity gainVO = ±2 V,CL = 100 pF
RL = 100 kΩ,Full
range0.05 0.05
V/µs
VEquivalent input noise f = 10 Hz 25°C 38 38
nV/√HzVnq
voltage f = 1 kHz 25°C 19 19nV/√Hz
VN(PP)
Peak-to-peakequivalent input noise
f = 0.1 Hz to 1 Hz 25°C 0.8 0.8µVVN(PP) equivalent input noise
voltage f = 0.1 Hz to 10 Hz 25°C 1.1 1.1µV
InEquivalent input noisecurrent
25°C 0.6 0.6 fA /√Hz
THD + NTotal harmonic
VO = ±2.3 V,RL 50 kΩ
AV = 125°C
0.2% 0.2%THD + N
distortion plus noiseRL = 50 kΩ,f = 20 kHz AV = 10
25°C1% 1%
Gain-bandwidth productf =10 kHz,CL = 100 pF
RL = 50 kΩ,25°C 0.21 0.21 MHz
BOMMaximum output-swingbandwidth
VO(PP) = 4.6 V,RL = 50 kΩ,
AV = 1,CL = 100 pF
25°C 14 14 kHz
φmPhase margin at unitygain RL = 50 kΩ, CL = 100 pF
25°C 63° 63°
Gain marginL L
25°C 15 15 dB† Full range is – 40°C to 125°C for Q suffix, – 55°C to 125°C for M suffix.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
30 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Table of GraphsFIGURE
VIO Input offset voltageDistribution 2 – 5
VIO Input offset voltagevs Common-mode input voltage 6, 7
αVIO Input offset voltage temperature coefficient Distribution 8 – 11
IIB/IIO Input bias and input offset currents vs Free-air temperature 12
VI Input voltage rangevs Supply voltage 13
VI Input voltage rangey g
vs Free-air temperature 14
VOH High-level output voltage vs High-level output current 15
VOL Low-level output voltage vs Low-level output current 16, 17
VOM+ Maximum positive peak output voltage vs Output current 18
VOM– Maximum negative peak output voltage vs Output current 19
VO(PP) Maximum peak-to-peak output voltage vs Frequency 20
IOS Short circuit output currentvs Supply voltage 21
IOS Short-circuit output currenty g
vs Free-air temperature 22
VO Output voltage vs Differential input voltage 23, 24
Differential gain vs Load resistance 25
AVD Large signal differential voltage amplificationvs Frequency 26, 27
AVD Large-signal differential voltage amplificationq y
vs Free-air temperature,
28, 29
zo Output impedance vs Frequency 30, 31
CMRR Common mode rejection ratiovs Frequency 32
CMRR Common-mode rejection ratioq y
vs Free-air temperature 33
kSVR Supply voltage rejection ratiovs Frequency 34, 35
kSVR Supply-voltage rejection ratioq y
vs Free-air temperature,
36
IDD Supply currentvs Supply voltage 37
IDD Supply currenty g
vs Free-air temperature 38
SR Slew ratevs Load capacitance 39
SR Slew ratevs Free-air temperature 40
VO Inverting large-signal pulse response 41, 42
VO Voltage-follower large-signal pulse response 43, 44
VO Inverting small-signal pulse response 45, 46
VO Voltage-follower small-signal pulse response 47, 48
Vn Equivalent input noise voltage vs Frequency 49, 50
Noise voltage (referred to input) Over a 10-second period 51
Integrated noise voltage vs Frequency 52
THD + N Total harmonic distortion plus noise vs Frequency 53
Gain bandwidth productvs Free-air temperature 54
Gain-bandwidth productvs Supply voltage 55
φ Phase marginvs Frequency 26, 27φm Phase margin
q yvs Load capacitance
,56
Am Gain margin vs Load capacitance 57
B1 Unity-gain bandwidth vs Load capacitance 58
Overestimation of phase margin vs Load capacitance 59
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
31POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 2
Per
cen
tag
e o
f Am
plif
iers
– %
DISTRIBUTION OF TLC2252INPUT OFFSET VOLTAGE
VIO – Input Offset Voltage – mV
10
5
30
0
20
15
25
35
–1.6 –0.8 0 0.8 1.6
682 Amplifiers From 1 Wafer LotsVDD± = ± 2.5 VP PackageTA = 25°C
Figure 3
Per
cen
tag
e o
f Am
plif
iers
– %
DISTRIBUTION OF TLC2252INPUT OFFSET VOLTAGE
VIO – Input Offset Voltage – mV
10
5
30
0
20
15
25
35
–1.6 –0.8 0 0.8 1.6
682 Amplifiers From 1 Wafer LotsVDD± = ± 5 VP PackageTA = 25°C
Figure 4
Per
cen
tag
e o
f Am
plif
iers
– %
DISTRIBUTION OF TLC2254INPUT OFFSET VOLTAGE
VIO – Input Offset Voltage – mV
15
10
5
0
20
–1.6 0 0.8 1.6–0.8
1020 Amplifiers From 1 Wafer LotVDD = ±2.5 VTA = 25°C
Figure 5
Per
cen
tag
e o
f Am
plif
iers
– %
DISTRIBUTION OF TLC2254INPUT OFFSET VOLTAGE
VIO – Input Offset Voltage – mV
15
10
5
0
20
25
–1.6 0 0.8 1.6–0.8
1020 Amplifiers From 1 Wafer LotVDD± = ±5 VTA = 25°C
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
32 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 6
VIO
– In
pu
t O
ffse
t V
olt
age
– m
V
INPUT OFFSET VOLTAGE†
vsCOMMON-MODE INPUT VOLTAGE
ÁÁÁÁÁÁV
IO
VIC – Common-Mode Input Voltage – V
1
0.8
0.6
0.4
0.2
0
–0.2
–0.4
–0.6
–0.8
–1–1 0 1 2 3 4 5
VDD = 5 VRS = 50 ΩTA = 25°C
Figure 7
VIO
– In
pu
t O
ffse
t V
olt
age
– m
V
INPUT OFFSET VOLTAGEvs
COMMON-MODE INPUT VOLTAGE
ÁÁÁÁÁÁ
VIO
VIC – Common-Mode Input Voltage – V
VDD± = ±5 VRS = 50 ΩTA = 25°C
1
0.8
0.6
0.4
0.2
0
–0.2
–0.4
–0.6
–0.8
–1–6 –5 –4 –3 –2 –1 0 1 2 3 4 5
Figure 8
Pre
cen
tag
e o
f Am
plif
iers
– %
15
10
5
0
20
25
–1 0 1 2
P PackageTA = 25°C to 125°C
DISTRIBUTION OF TLC2252 INPUT OFFSETVOLTAGE TEMPERATURE COEFFICIENT
αVIO – Temperature Coefficient – µV/ °C
62 Amplifiers From1 Wafer LotVDD = ±2.5 V
Figure 9
Per
cen
tag
e o
f Am
plif
iers
– %
15
10
5
0
20
25
–1 0 1 2
62 Amplifiers From1 Wafer LotVDD = ±5 VP PackageTA = 25°C to 125°C
DISTRIBUTION OF TLC2252 INPUT OFFSETVOLTAGE TEMPERATURE COEFFICIENT
αVIO – Temperature Coefficient – µV/ °C
† For curves where VDD = 5 V, all loads are referenced to 2.5 V.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
33POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 10
Per
cen
tag
e o
f Am
plif
iers
– %
DISTRIBUTION OF TLC2254 INPUT OFFSETVOLTAGE TEMPERATURE COEFFICIENT
αVIO – Temperature Coefficient ofInput Offset Voltage – µV/ °C
15
10
5
0
20
25
–2 –1 0 1 2
62 Amplifiers From1 Wafer LotVDD± = ± 2.5 VP PackageTA = 25°C to 125°C
Figure 11
Per
cen
tag
e o
f Am
plif
iers
– %
DISTRIBUTION OF TLC2254 INPUT OFFSETVOLTAGE TEMPERATURE COEFFICIENT
αVIO – Temperature Coefficient ofInput Offset Voltage – µV/ °C
15
10
5
0
20
25
–2 –1 0 1 2
62 Amplifiers From1 Wafer LotVDD± = ± 5 VP PackageTA = 25°C to 125°C
Figure 12
10
5
30
025 45 65 85IIB
an
d II
O –
Inp
ut
Bia
s an
d In
pu
t O
ffse
t C
urr
ents
– p
A
20
15
25
INPUT BIAS AND INPUT OFFSET CURRENTS†
vsFREE-AIR TEMPERATURE
35
105 125
IIB
IIO
VDD± = ±2.5 VVIC = 0VO = 0RS = 50 Ω
TA – Free-Air Temperature – °C
ÁÁÁÁ
I IBI IO
Figure 13
0
2 3 4 5
VI –
Inp
ut
Vo
ltag
e R
ang
e –
V
4
8
INPUT VOLTAGE RANGEvs
SUPPLY VOLTAGE10
6 7 8
6
2
–2
–4
–6
–8
–10
| VIO | ≤ 5 mV
RS = 50 ΩTA = 25°C
VI
| VDD± | – Supply Voltage – V
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
34 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 14
5
2
1
0
VI –
Inp
ut
Vo
ltag
e R
ang
e –
V
3
4
INPUT VOLTAGE RANGE†
vsFREE-AIR TEMPERATURE
5
–1–75 –55 –35 –15 25 45 65 85 105 125
VDD = 5 V
ÁÁÁÁ
VI
TA – Free-Air Temperature – °C
Figure 15
VO
H –
Hig
h-L
evel
Ou
tpu
t V
olt
age
– V
HIGH-LEVEL OUTPUT VOLTAGE†‡
vsHIGH-LEVEL OUTPUT CURRENT
| IOH| – High-Level Output Current – µA
ÁÁÁÁÁÁ
V OH
3
2
1
00 200 400
4
5
600 800
VDD = 5 V
TA = –40°C
TA = 25°C
TA = 125°C
TA = –55°C
Figure 16
0.6
0.4
0.2
00 1 2 3
VO
L –
Lo
w-L
evel
Ou
tpu
t V
olt
age
– V
0.8
1
LOW-LEVEL OUTPUT VOLTAGE‡
vsLOW-LEVEL OUTPUT CURRENT
1.2
4 5
VIC = 0VIC = 1.25 V
VIC = 2.5 V
VDD = 5 VTA = 25°C
ÁÁÁÁÁÁÁÁÁ
V OL
IOL – Low-Level Output Current – mA
Figure 17
0.8
0.4
0.2
00 1 2 3
VO
L –
Lo
w-L
evel
Ou
tpu
t V
olt
age
– V
1
1.2
LOW-LEVEL OUTPUT VOLTAGE†‡
vsLOW-LEVEL OUTPUT CURRENT
1.4
4 5 6
0.6
IOL – Low-Level Output Current – mA
TA = 125°C
TA = 25°C
TA = –55°C
VDD = 5 VVIC = 2.5 V
ÁÁÁÁÁÁ
V OL
TA = –40°C
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.‡ For curves where VDD = 5 V, all loads are referenced to 2.5 V.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
35POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 18
MAXIMUM POSITIVE PEAK OUTPUT VOLTAGE†
vsOUTPUT CURRENT
IO – Output Current – µA
3
2
1
00 200 400
4
5
600 800
TA = 125°C
TA = 25°C
VO
M +
– M
axim
um
Po
siti
ve P
eak
Ou
tpu
t V
olt
age
– V
ÁÁÁÁÁÁ
VO
M +
TA = –40°C
VDD = ±5 V
TA = –55°C
Figure 19
0 1 2
VO
M –
– M
axim
um
Neg
ativ
e P
eak
Ou
tpu
t V
olt
age
– V
MAXIMUM NEGATIVE PEAK OUTPUT VOLTAGE†
vsOUTPUT CURRENT
3 4 5 6
–3.8
–4
–4.2
–4.4
–4.6
–4.8
–5
VDD± = ±5 VVIC = 0
TA = 125°C
TA = 25°C
TA = –40°C
IO – Output Current – mA
ÁÁÁÁÁÁ
VO
M –
TA = –55°C
Figure 20
VO
(PP
) –
Max
imu
m P
eak-
to-P
eak
Ou
tpu
t V
olt
age
– V
f – Frequency – Hz
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE‡
vsFREQUENCY
ÁÁÁÁÁÁV
O(P
P)
6
5
3
1
0
10
4
8
7
9
2
102 103 104 105
VDD = 5 V
VDD± = ±5 VRL = 50 kΩTA = 25°C
Figure 21
IOS
– S
ho
rt-C
ircu
it O
utp
ut
Cu
rren
t –
mA
SHORT-CIRCUIT OUTPUT CURRENTvs
SUPPLY VOLTAGE
I OS
| VDD± | – Supply Voltage – V
5
3
1
2 3 4 5
7
8
10
6 7 8
9
6
4
2
0
–1
VID = –100 mV
VID = 100 mV
VO = 0TA = 25°CVIC = 0
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.‡ For curves where VDD = 5 V, all loads are referenced to 2.5 V.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
36 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 22
IOS
– S
ho
rt-C
ircu
it O
utp
ut
Cu
rren
t –
mA
SHORT-CIRCUIT OUTPUT CURRENT†
vsFREE-AIR TEMPERATURE
TA – Free-Air Temperature – °C
I OS
11
10
9
8
7
6
5
4
3
2
1
0
–1–75 –50 –25 0 25 50 75 100 125
VID = –100 mV
VID = 100 mV
VO = 0VDD± = ±5 V
Figure 23
3
2
1
00 250
4
5
OUTPUT VOLTAGE‡
vsDIFFERENTIAL INPUT VOLTAGE
500 750 1000
VID – Differential Input Voltage – µV
– O
utp
ut
Vo
ltag
e –
VV
O
–1000 –750 –250–500
VDD = 5 VRL = 50 kΩVIC = 2.5 VTA = 25°C
Figure 24
1
–1
–3
–50 250
3
5
OUTPUT VOLTAGEvs
DIFFERENTIAL INPUT VOLTAGE
500 750 1000
VID – Differential Input Voltage – µV
VDD± = ±5 VVIC = 0RL = 50 kΩTA = 25°C
– O
utp
ut
Vo
ltag
e –
VV
O
–1000 –750 –250–500
Figure 25
Dif
fere
nti
al G
ain
– V
/ mV
DIFFERENTIAL GAIN‡
vsLOAD RESISTANCE
RL – Load Resistance – kΩ
104
103
102
101 101 102 103
VO (PP) = 2 VTA = 25°C
VDD = ±5 V
VDD = 5 V
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.‡ For curves where VDD = 5 V, all loads are referenced to 2.5 V.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
37POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
om
– P
has
e M
arg
in
φ m
f – Frequency – Hz
LARGE-SIGNAL DIFFERENTIAL VOLTAGEAMPLIFICATION AND PHASE MARGIN†
vsFREQUENCY
AV
D –
Lar
ge-
Sig
nal
Dif
fere
nti
al
ÁÁÁÁÁÁ
AV
D Vo
ltag
e A
mp
lific
atio
n –
dB
20
80
60
40
0
–20
–40103 104 105 106 107
180°
135°
90°
45°
0°
–45°
–90°
Gain
VDD = 5 VRL = 50 kΩCL= 100 pFTA = 25°C
Phase Margin
Figure 26
om
– P
has
e M
arg
in
φ m
f – Frequency – Hz
LARGE-SIGNAL DIFFERENTIAL VOLTAGEAMPLIFICATION AND PHASE MARGIN
vsFREQUENCY
AV
D –
Lar
ge-
Sig
nal
Dif
fere
nti
al
ÁÁÁÁÁÁ
AV
D Vo
ltag
e A
mp
lific
atio
n –
dB
20
80
60
40
0
–20
–40103 104 105 106 107
180°
135°
90°
45°
0°
–45°
–90°
Gain
VDD = ±10 VRL= 50 kΩCL= 100 pFTA = 25°C
Phase Margin
Figure 27
† For curves where VDD = 5 V, all loads are referenced to 2.5 V.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
38 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 28
LARGE-SIGNAL DIFFERENTIALVOLTAGE AMPLIFICATION†‡
vsFREE-AIR TEMPERATURE
TA – Free-Air Temperature – °C
AV
D –
Lar
ge-
Sig
nal
Dif
fere
nti
al
ÁÁ
AV
D Vo
ltag
e A
mp
lific
atio
n –
V/m
V
–50 –25 0 25 50 75 100 125
VDD = 5 VVIC = 2.5 VVO = 1 V to 4 V
RL = 50 kΩ
RL = 1 MΩ
104
103
102
–75101
Figure 29
TA – Free-Air Temperature – °C
LARGE-SIGNAL DIFFERENTIALVOLTAGE AMPLIFICATION†
vsFREE-AIR TEMPERATURE
AV
D –
Lar
ge-
Sig
nal
Dif
fere
nti
alÁÁÁÁ
AV
D Vo
ltag
e A
mp
lific
atio
n –
V/m
V
–50 –25 0 25 50 75 100 125
VDD± = ±5 VVIC = 0VO = ±4 V
RL = 50 kΩ
104
103
102
RL = 1 MΩ
–75101
Figure 30
zo –
Ou
tpu
t Im
ped
ance
– 0
OUTPUT IMPEDANCE‡
vsFREQUENCY
f – Frequency – Hz
Ωz o
10
1
0.1
1000
100
102 103 104 105 106
VDD = 5 VTA = 25°C
AV = 100
AV = 10
AV = 1
Figure 31
OUTPUT IMPEDANCEvs
FREQUENCY
f – Frequency – Hz
zo –
Ou
tpu
t Im
ped
ance
– 0 Ω
z o
10
1
0.1
1000
100
102 103 104 105 106
VDD± = ±5 VTA = 25°C
AV = 100
AV = 10
AV = 1
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.‡ For curves where VDD = 5 V, all loads are referenced to 2.5 V.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
39POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 32
f – Frequency – Hz
COMMON-MODE REJECTION RATIO†
vsFREQUENCY
CM
RR
– C
om
mo
n-M
od
e R
ejec
tio
n R
atio
– d
B
80
40
20
0
100
60
101 102 103 104 105 166
VDD = 5 V
VDD± = ±5 V
Figure 33
COMMON-MODE REJECTION RATIO†‡
vsFREE-AIR TEMPERATURE
TA – Free-Air Temperature – °C
CM
RR
– C
om
mo
n-M
od
e R
ejec
tio
n R
atio
– d
B
84
82
92
80
88
86
90
94
–50 –25 0 25 50 75 100 125
VDD = 5 V
VDD± = ±5 V
–75
Figure 34
f – Frequency – Hz
SUPPLY-VOLTAGE REJECTION RATIO†
vsFREQUENCY
KS
VR
– S
up
ply
-Vo
ltag
e R
ejec
tio
n R
atio
– d
B
ÁÁÁÁÁÁ
kS
VR
100
80
60
40
20
0
–20101 102 103 104 105 106
kSVR–
VDD = 5 VTA = 25°CkSVR+
Figure 35
KS
VR
– S
up
ply
-Vo
ltag
e R
ejec
tio
n R
atio
– d
B
f – Frequency – Hz
SUPPLY-VOLTAGE REJECTION RATIOvs
FREQUENCY
ÁÁÁÁÁÁÁÁÁ
kS
VR
100
80
60
40
20
0
–20101 102 103 104 105 106
kSVR+
kSVR–
VDD± = ±5 VTA = 25°C
‡ Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
† For curves where VDD = 5 V, all loads are referenced to 2.5 V.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
40 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 36
KS
VR
– S
up
ply
-Vo
ltag
e R
ejec
tio
n R
atio
– d
B
SUPPLY-VOLTAGE REJECTION RATIO†
vsFREE-AIR TEMPERATURE
ÁÁÁÁÁÁ
kS
VR
TA – Free-Air Temperature – °C
100
95
90
105
110
–50 –25 0 25 50 75 100 125
VDD± = ±2.2 V to ±8 VVO = 0
–75
Figure 37
IDD
– S
up
ply
Cu
rren
t –
uA
SUPPLY CURRENT†
vsSUPPLY VOLTAGE
| VDD± | – Supply Voltage – V
ÁÁÁÁÁÁ
I DD
Aµ
120
80
40
00 1 2 3 4 5
160
200
240
6 7 8
TA = 25°C
TA = 125°C
VO = 0 No Load
TA = –55°C
TA = –40°C
Figure 38
SUPPLY CURRENT†‡
vsFREE-AIR TEMPERATURE
IDD
– S
up
ply
Cu
rren
t –
uA
ÁÁÁÁ
I DD
Aµ
TA – Free-Air Temperature – °C
120
80
40
0
160
200
240
–50 –25 0 25 50 75 100 125
VDD± = ±5 VVO = 0
VDD = 5 VVO = 2.5 V
–75
Figure 39
SR
– S
lew
Rat
e –
v/u
s
SLEW RATE‡
vsLOAD CAPACITANCE
sµ
V/
CL – Load Capacitance – pF
0.16
0.08
0.04
0
0.2
0.12
101 102 103 104
VDD = 5 VAV = –1TA = 25°C
SR–
0.18
0.14
0.1
0.06
0.02
SR+
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.‡ For curves where VDD = 5 V, all loads are referenced to 2.5 V.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
41POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 40
SLEW RATE†‡
vsFREE-AIR TEMPERATURE
TA – Free-Air Temperature – °C
SR
– S
lew
Rat
e –
v/u
ssµV
/
0.12
0.08
0.04
0
0.16
0.2
–50 –25 0 25 50 75 100 125
SR+
SR–
VDD = 5 VRL = 50 kΩCL = 100 pFAV = 1
–75
Figure 41
VO
– O
utp
ut
Vo
ltag
e –
V
INVERTING LARGE-SIGNAL PULSERESPONSE‡
VO
t – Time – µs
2
1
00 10 20 30 40 50 60
3
4
5
70 80 90 100
VDD = 5 VRL = 50 kΩCL = 100 pFAV = –1TA = 25°C
Figure 42
t – Time – µs
VO
– O
utp
ut
Vo
ltag
e –
VV
O
INVERTING LARGE-SIGNAL PULSERESPONSE
0
4
0 10 20 30 40 50 60
2
1
3
5
70 80 90 100
VDD± = ±5 VRL = 50 kΩCL = 100 pFAV = –1TA = 25°C
–1
–2
–3
–4
–5
Figure 43
VOLTAGE-FOLLOWER LARGE-SIGNALPULSE RESPONSE‡
t – Time – µs
VO
– O
utp
ut
Vo
ltag
e –
VV
O
2
1
00 10 20 30 40 50 60
3
4
5
70 80 90 100
VDD = 5 VRL = 50 kΩCL = 100 pFAV = 1TA = 25°C
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.‡ For curves where VDD = 5 V, all loads are referenced to 2.5 V.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
42 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 44
VO
– O
utp
ut
Vo
ltag
e –
VV
O
VOLTAGE-FOLLOWER LARGE-SIGNALPULSE RESPONSE
0
4
0 10 20 30 40 50 60
2
1
3
5
70 80 90 100
VDD± = ±5 VRL = 50 kΩCL = 100 pFAV = 1TA = 25°C
–1
–2
–3
–4
–5
t – Time – µs
Figure 45
INVERTING SMALL-SIGNALPULSE RESPONSE†
VO
– O
utp
ut
Vo
ltag
e –
VV
O
t – Time – µs
2.5
2.45
2.40 10 20 30
2.55
2.6
2.65
40 50
VDD = 5 VRL = 50 kΩCL = 100 pFAV = –1TA = 25°C
Figure 46
INVERTING SMALL-SIGNALPULSE RESPONSE
t – Time – µs
VO
– O
utp
ut
Vo
ltag
e –
mV
VO
0
0 10 20 30
0.1
40 50
0.05
–0.05
–0.1
VDD± = ±5 VRL = 50 kΩCL = 100 pFAV = –1TA = 25°C
Figure 47
VOLTAGE-FOLLOWER SMALL-SIGNALPULSE RESPONSE†
VO
– O
utp
ut
Vo
ltag
e –
VV
O
t – Time – µs
2.5
2.45
2.4
0 10 20 30
2.55
2.6
2.65
40 50
VDD = 5 VRL = 50 kΩCL = 100 pFAV = 1TA = 25°C
† For curves where VDD = 5 V, all loads are referenced to 2.5 V.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
43POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 48
VOLTAGE-FOLLOWER SMALL-SIGNALPULSE RESPONSE
VO
– O
utp
ut
Vo
ltag
e –
VV
O
t – Time – µs0 10 20 30 40 50
VDD± = ±5 VRL = 50 kΩCL = 100 pFAV = 1TA = 25°C
–0.1
–0.05
0
0.05
0.1
Figure 49
VN
– E
qu
ival
ent
Inp
ut
No
ise
Vo
ltag
e –
nv/
/Hz
f – Frequency – Hz
EQUIVALENT INPUT NOISE VOLTAGE†
vsFREQUENCY
nV
/H
zV
n
40
20
10
0
60
30
50
101 102 103 104
VDD = 5 VRS = 20 ΩTA = 25°C
Figure 50
EQUIVALENT INPUT NOISE VOLTAGEvs
FREQUENCY
f – Frequency – Hz
VN
– E
qu
ival
ent
Inp
ut
No
ise
Vo
ltag
e –
nv/
/Hz
nV
/H
zV
n
40
20
10
0
60
30
50
101 102 103 104
VDD± = ±5 VRS = 20 ΩTA = 25°C
Figure 51
No
ise
Vo
ltag
e –
nV
t – Time – s
EQUIVALENT INPUT NOISE VOLTAGE OVERA 10-SECOND PERIOD†
0 2 4 6
0
750
1000
8 10
500
–250
–500
–750
–1000
250
VDD = 5 Vf = 0.1 Hz to 10 HzTA = 25°C
† For curves where VDD = 5 V, all loads are referenced to 2.5 V.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
44 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 52
0.1
Inte
gra
ted
No
ise
Vo
ltag
e –
f – Frequency – Hz
INTEGRATED NOISE VOLTAGEvs
FREQUENCY
1
10
100
1 101 102 103 104 105
Calculated Using Ideal Pass-Band FilterLow Frequency = 1 HzTA = 25°CV
µ
Figure 53
TH
D +
N –
To
tal H
arm
on
ic D
isto
rtio
n P
lus
No
ise
– %
f – Frequency – Hz
TOTAL HARMONIC DISTORTION PLUS NOISE†
vsFREQUENCY
0.01
1
0.001101 102 103 104 105
AV = 10
AV = 1VDD = 5 VRL = 50 kΩTA = 25°C
0.1
AV = 100
Figure 54
Gai
n-B
and
wid
th P
rod
uct
– k
Hz
GAIN-BANDWIDTH PRODUCT†‡
vsFREE-AIR TEMPERATURE
TA – Free-Air Temperature – °C
200
120
80
240
280
–75 –25 0 25 50 75 100 125
VDD = 5 Vf = 10 kHzRL = 50 kΩCL = 100 pF
–50
160
Figure 55
Gai
n-B
and
wid
th P
rod
uct
– k
Hz
GAIN-BANDWIDTH PRODUCTvs
SUPPLY VOLTAGE
| VDD ± | – Supply Voltage – V
210
190
170
1500 2 3 5
230
250
7 81 4 6
TA = 25°C
‡ Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
† For curves where VDD = 5 V, all loads are referenced to 2.5 V.
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
45POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 56
om
– P
has
e M
arg
in
PHASE MARGINvs
LOAD CAPACITANCE
CL – Load Capacitance – pF
mφ
101 102 103 105
75°
60°
45°
30°
15°
0°
Rnull = 200 Ω
Rnull = 500 Ω
Rnull = 50 Ω
Rnull = 0
TA = 25°C
Rnull = 10 Ω
104
50 kΩ
50 kΩ
VDD –
VDD +Rnull
CLVI
+–
Rnull = 100 Ω
Figure 57
Gai
n M
arg
in –
dB
GAIN MARGINvs
LOAD CAPACITANCE
CL – Load Capacitance – pF
20
10
5
0
15
101 102 103 105
Rnull = 100 Ω
TA = 25°C
Rnull = 50 Ω
104
Rnull = 500 Ω
Rnull = 200 Ω
Rnull = 0
Rnull = 10 Ω
Figure 58
– U
nit
y-G
ain
Ban
dw
idth
– k
Hz
UNITY-GAIN BANDWIDTH†
vsLOAD CAPACITANCE
CL – Load Capacitance – pF
ÁÁÁÁ
B1
150
25
100
0
200
125
175
50
75
101 102 103 104 105
TA = 25°C
Figure 59
Ove
rest
imat
ion
of P
has
e M
arg
in
OVERESTIMATION OF PHASE MARGIN†
vsLOAD CAPACITANCE
CL – Load Capacitance – pF
15
10
5
0
20
25
101 102 103 104 105
TA = 25°C
Rnull = 100 Ω
Rnull = 50 Ω
Rnull = 10 Ω
Rnull = 500 Ω
Rnull = 200 Ω
† See application information
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
46 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
driving large capacitive loads
The TLC225x is designed to drive larger capacitive loads than most CMOS operational amplifiers. Figure 56and Figure 57 illustrate its ability to drive loads up to 1000 pF while maintaining good gain and phase margins(Rnull = 0).
A smaller series resistor (Rnull) at the output of the device (see Figure 60) improves the gain and phase marginswhen driving large capacitive loads. Figure 56 and Figure 57 show the effects of adding series resistances of10 Ω , 50 Ω , 100 Ω , 200 Ω , and 500 Ω . The addition of this series resistor has two effects: the first is that it addsa zero to the transfer function and the second is that it reduces the frequency of the pole associated with theoutput load in the transfer function.
The zero introduced to the transfer function is equal to the series resistance times the load capacitance. Tocalculate the improvement in phase margin, equation 1 can be used.
∆φm1 tan–1 2 × π × UGBW × Rnull × CL
Where :
(1)
∆φm1 Improvement in phase margin
UGBW Unity-gain bandwidth frequency
Rnull Output series resistance
CL Load capacitance
The unity-gain bandwidth (UGBW) frequency decreases as the capacitive load increases (see Figure 58). Touse equation 1, UGBW must be approximated from Figure 58.
Using equation 1 alone overestimates the improvement in phase margin, as illustrated in Figure 59. Theoverestimation is caused by the decrease in the frequency of the pole associated with the load, thus providingadditional phase shift and reducing the overall improvement in phase margin.
Using Figure 60, with equation 1 enables the designer to choose the appropriate output series resistance tooptimize the design of circuits driving large capacitance loads.
50 kΩ
50 kΩ
VDD– /GND
VDD+
Rnull
CL
VI+
–
Figure 60. Series-Resistance Circuit
TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001
47POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
macromodel information
Macromodel information provided was derived using MicroSim Parts , the model generation software usedwith MicroSim PSpice . The Boyle macromodel (see Note 5) and subcircuit in Figure 61 are generated usingthe TLC225x typical electrical and operating characteristics at TA = 25°C. Using this information, outputsimulations of the following key parameters can be generated to a tolerance of 20% (in most cases):
Maximum positive output voltage swing Maximum negative output voltage swing Slew rate Quiescent power dissipation Input bias current Open-loop voltage amplification
Unity-gain frequency Common-mode rejection ratio Phase margin DC output resistance AC output resistance Short-circuit output current limit
NOTE 5: G. R. Boyle, B. M. Cohn, D. O. Pederson, and J. E. Solomon, “Macromodeling of Integrated Circuit Operational Amplifiers”, IEEE Journalof Solid-State Circuits, SC-9, 353 (1974).
OUT
+
–
+
–
+
–
+
–
+–
+
–
+
– +
–
+–
.SUBCKT TLC225x 1 2 3 4 5C1 11 12 6.369E–12C2 6 7 25.00E–12DC 5 53 DXDE 54 5 DXDLP 90 91 DXDLN 92 90 DXDP 4 3 DXEGND 99 0 POLY (2) (3,0) (4,0) 0 .5 .5FB 7 99 POLY (5) VB VC VE VLP+ VLN 0 57.62E6 –60E6 60E6 60E6 –60E6GA 6 0 11 12 26.86E–6GCM 0 6 10 99 2.686E–9ISS 3 10 DC 3.1E–6HLIM 90 0 VLIM 1KJ1 11 2 10 JXJ2 12 1 10 JXR2 6 9 100.0E3
RD1 60 11 37.23E3RD2 60 12 37.23E3R01 8 5 84R02 7 99 84RP 3 4 71.43E3RSS 10 99 64.52E6VAD 60 4 –.5VB 9 0 DC 0VC 3 53 DC .605VE 54 4 DC .605VLIM 7 8 DC 0VLP 91 0 DC –.235VLN 0 92 DC 7.5.MODEL DX D (IS=800.0E–18).MODEL JX PJF (IS=500.0E–15 BETA=139E–6+ VTO=–.05).ENDS
VCC+
RP
IN –2
IN+1
VCC–
VAD
RD1
11
J1 J2
10
RSS ISS
3
12
RD2
60
VE
54DE
DP
VC
DC
4
C1
53
R2
6
9
EGND
VB
FB
C2
GCM GA VLIM
8
5
RO1
RO2
HLIM
90
DLP
91
DLN
92
VLNVLP
99
7
Figure 61. Boyle Macromodel and Subcircuit
PSpice and Parts are trademarks of MicroSim Corporation.
PACKAGE OPTION ADDENDUM
www.ti.com 17-Mar-2017
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status(1)
Package Type PackageDrawing
Pins PackageQty
Eco Plan(2)
Lead/Ball Finish(6)
MSL Peak Temp(3)
Op Temp (°C) Device Marking(4/5)
Samples
5962-9564001Q2A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9564001Q2ATLC2252MFKB
5962-9564001QHA ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9564001QHATLC2252M
5962-9564001QPA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9564001QPATLC2252M
5962-9564002Q2A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9564002Q2ATLC2254MFKB
5962-9564002QDA ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9564002QDATLC2254MWB
5962-9564003NXD ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM -55 to 125 Q2252A
5962-9564003NXDR ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM -55 to 125 Q2252A
5962-9564003Q2A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9564003Q2ATLC2252AMFKB
5962-9564003QHA ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9564003QHATLC2252AM
5962-9564003QPA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9564003QPATLC2252AM
5962-9564004Q2A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9564004Q2ATLC2254AMFKB
5962-9564004QDA ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9564004QDATLC2254AMWB
TLC2252AID ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 2252AI
PACKAGE OPTION ADDENDUM
www.ti.com 17-Mar-2017
Addendum-Page 2
Orderable Device Status(1)
Package Type PackageDrawing
Pins PackageQty
Eco Plan(2)
Lead/Ball Finish(6)
MSL Peak Temp(3)
Op Temp (°C) Device Marking(4/5)
Samples
TLC2252AIDG4 ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 2252AI
TLC2252AIDR ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 2252AI
TLC2252AIDRG4 ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 2252AI
TLC2252AIP ACTIVE PDIP P 8 50 Pb-Free(RoHS)
CU NIPDAU N / A for Pkg Type TLC2252AI
TLC2252AIPE4 ACTIVE PDIP P 8 50 Pb-Free(RoHS)
CU NIPDAU N / A for Pkg Type TLC2252AI
TLC2252AIPW ACTIVE TSSOP PW 8 150 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM Y2252A
TLC2252AIPWR ACTIVE TSSOP PW 8 2000 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM Y2252A
TLC2252AIPWRG4 ACTIVE TSSOP PW 8 2000 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM Y2252A
TLC2252AMFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9564003Q2ATLC2252AMFKB
TLC2252AMJGB ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9564003QPATLC2252AM
TLC2252AMUB ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9564003QHATLC2252AM
TLC2252AQDR ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM -40 to 125 C2252A
TLC2252AQDRG4 ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM C2252A
TLC2252CD ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 0 to 70 2252C
TLC2252CDG4 ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 0 to 70 2252C
TLC2252CDR ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 0 to 70 2252C
TLC2252CDRG4 ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 0 to 70 2252C
PACKAGE OPTION ADDENDUM
www.ti.com 17-Mar-2017
Addendum-Page 3
Orderable Device Status(1)
Package Type PackageDrawing
Pins PackageQty
Eco Plan(2)
Lead/Ball Finish(6)
MSL Peak Temp(3)
Op Temp (°C) Device Marking(4/5)
Samples
TLC2252CP ACTIVE PDIP P 8 50 Pb-Free(RoHS)
CU NIPDAU N / A for Pkg Type 0 to 70 TLC2252CP
TLC2252CPW ACTIVE TSSOP PW 8 150 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2252
TLC2252CPWG4 ACTIVE TSSOP PW 8 150 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2252
TLC2252CPWR ACTIVE TSSOP PW 8 2000 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2252
TLC2252CPWRG4 ACTIVE TSSOP PW 8 2000 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2252
TLC2252ID ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM -40 to 125 2252I
TLC2252IDG4 ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM -40 to 125 2252I
TLC2252IDR ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM -40 to 125 2252I
TLC2252IDRG4 ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM -40 to 125 2252I
TLC2252IP ACTIVE PDIP P 8 50 Pb-Free(RoHS)
CU NIPDAU N / A for Pkg Type -40 to 125 TLC2252IP
TLC2252MFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9564001Q2ATLC2252MFKB
TLC2252MJGB ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9564001QPATLC2252M
TLC2252MUB ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9564001QHATLC2252M
TLC2254AID ACTIVE SOIC D 14 50 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 2254AI
TLC2254AIDG4 ACTIVE SOIC D 14 50 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 2254AI
TLC2254AIDR ACTIVE SOIC D 14 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 2254AI
TLC2254AIDRG4 ACTIVE SOIC D 14 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 2254AI
PACKAGE OPTION ADDENDUM
www.ti.com 17-Mar-2017
Addendum-Page 4
Orderable Device Status(1)
Package Type PackageDrawing
Pins PackageQty
Eco Plan(2)
Lead/Ball Finish(6)
MSL Peak Temp(3)
Op Temp (°C) Device Marking(4/5)
Samples
TLC2254AIN ACTIVE PDIP N 14 25 Pb-Free(RoHS)
CU NIPDAU N / A for Pkg Type TLC2254AIN
TLC2254AIPW ACTIVE TSSOP PW 14 90 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM Y2254A
TLC2254AIPWR ACTIVE TSSOP PW 14 2000 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM Y2254A
TLC2254AIPWRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM Y2254A
TLC2254AMFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9564004Q2ATLC2254AMFKB
TLC2254AMWB ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9564004QDATLC2254AMWB
TLC2254AQD ACTIVE SOIC D 14 50 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM -40 to 125 TLC2254A
TLC2254AQDR ACTIVE SOIC D 14 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM -40 to 125 TLC2254A
TLC2254AQDRG4 ACTIVE SOIC D 14 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM PJ2254A
TLC2254CD ACTIVE SOIC D 14 50 Green (RoHS& no Sb/Br)
CU NIPDAU | Call TI Level-1-260C-UNLIM 0 to 70 TLC2254C
TLC2254CDG4 ACTIVE SOIC D 14 50 Green (RoHS& no Sb/Br)
Call TI Level-1-260C-UNLIM 0 to 70 TLC2254C
TLC2254CDR ACTIVE SOIC D 14 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 0 to 70 TLC2254C
TLC2254CDRG4 ACTIVE SOIC D 14 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 0 to 70 TLC2254C
TLC2254CN ACTIVE PDIP N 14 25 Pb-Free(RoHS)
CU NIPDAU N / A for Pkg Type 0 to 70 TLC2254CN
TLC2254CPW ACTIVE TSSOP PW 14 90 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2254
TLC2254CPWG4 ACTIVE TSSOP PW 14 90 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2254
TLC2254CPWR ACTIVE TSSOP PW 14 2000 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2254
PACKAGE OPTION ADDENDUM
www.ti.com 17-Mar-2017
Addendum-Page 5
Orderable Device Status(1)
Package Type PackageDrawing
Pins PackageQty
Eco Plan(2)
Lead/Ball Finish(6)
MSL Peak Temp(3)
Op Temp (°C) Device Marking(4/5)
Samples
TLC2254CPWRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2254
TLC2254ID ACTIVE SOIC D 14 50 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM TLC2254I
TLC2254IDG4 ACTIVE SOIC D 14 50 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM TLC2254I
TLC2254IDR ACTIVE SOIC D 14 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM TLC2254I
TLC2254IDRG4 ACTIVE SOIC D 14 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM TLC2254I
TLC2254IN ACTIVE PDIP N 14 25 Pb-Free(RoHS)
CU NIPDAU N / A for Pkg Type TLC2254IN
TLC2254MFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9564002Q2ATLC2254MFKB
TLC2254MWB ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9564002QDATLC2254MWB
(1) The marketing status values are defined as follows:ACTIVE: Product device recommended for new designs.LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.PREVIEW: Device has been announced but is not in production. Samples may or may not be available.OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availabilityinformation and additional product content details.TBD: The Pb-Free/Green conversion plan has not been defined.Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement thatlead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used betweenthe die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weightin homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
PACKAGE OPTION ADDENDUM
www.ti.com 17-Mar-2017
Addendum-Page 6
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuationof the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finishvalue exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on informationprovided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken andcontinues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TLC2252, TLC2252A, TLC2252AM, TLC2252M, TLC2254, TLC2254A, TLC2254AM, TLC2254M :
• Catalog: TLC2252A, TLC2252, TLC2254A, TLC2254
• Automotive: TLC2252-Q1, TLC2252A-Q1, TLC2252A-Q1, TLC2252-Q1, TLC2254-Q1, TLC2254A-Q1, TLC2254A-Q1, TLC2254-Q1
• Enhanced Product: TLC2252A-EP, TLC2252A-EP, TLC2254A-EP, TLC2254A-EP
• Military: TLC2252M, TLC2252AM, TLC2254M, TLC2254AM
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
• Enhanced Product - Supports Defense, Aerospace and Medical Applications
• Military - QML certified for Military and Defense Applications
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device PackageType
PackageDrawing
Pins SPQ ReelDiameter
(mm)
ReelWidth
W1 (mm)
A0(mm)
B0(mm)
K0(mm)
P1(mm)
W(mm)
Pin1Quadrant
5962-9564003NXDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLC2252AIDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLC2252AIDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLC2252AIPWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
TLC2252AQDR SOIC D 8 2500 330.0 12.5 6.4 5.2 2.1 8.0 12.0 Q1
TLC2252CDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLC2252CPWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
TLC2252IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLC2254AIDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
TLC2254AIPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1
TLC2254AQDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
TLC2254CDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
TLC2254CPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1
TLC2254IDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 18-Oct-2016
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
5962-9564003NXDR SOIC D 8 2500 367.0 367.0 38.0
TLC2252AIDR SOIC D 8 2500 367.0 367.0 38.0
TLC2252AIDR SOIC D 8 2500 340.5 338.1 20.6
TLC2252AIPWR TSSOP PW 8 2000 367.0 367.0 35.0
TLC2252AQDR SOIC D 8 2500 340.5 338.1 20.6
TLC2252CDR SOIC D 8 2500 340.5 338.1 20.6
TLC2252CPWR TSSOP PW 8 2000 367.0 367.0 35.0
TLC2252IDR SOIC D 8 2500 340.5 338.1 20.6
TLC2254AIDR SOIC D 14 2500 367.0 367.0 38.0
TLC2254AIPWR TSSOP PW 14 2000 367.0 367.0 35.0
TLC2254AQDR SOIC D 14 2500 367.0 367.0 38.0
TLC2254CDR SOIC D 14 2500 367.0 367.0 38.0
TLC2254CPWR TSSOP PW 14 2000 367.0 367.0 35.0
TLC2254IDR SOIC D 14 2500 367.0 367.0 38.0
PACKAGE MATERIALS INFORMATION
www.ti.com 18-Oct-2016
Pack Materials-Page 2
MECHANICAL DATA
MCER001A – JANUARY 1995 – REVISED JANUARY 1997
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE
0.310 (7,87)0.290 (7,37)
0.014 (0,36)0.008 (0,20)
Seating Plane
4040107/C 08/96
5
40.065 (1,65)0.045 (1,14)
8
1
0.020 (0,51) MIN
0.400 (10,16)0.355 (9,00)
0.015 (0,38)0.023 (0,58)
0.063 (1,60)0.015 (0,38)
0.200 (5,08) MAX
0.130 (3,30) MIN
0.245 (6,22)0.280 (7,11)
0.100 (2,54)
0°–15°
NOTES: A. All linear dimensions are in inches (millimeters).B. This drawing is subject to change without notice.C. This package can be hermetically sealed with a ceramic lid using glass frit.D. Index point is provided on cap for terminal identification.E. Falls within MIL STD 1835 GDIP1-T8
www.ti.com
PACKAGE OUTLINE
C
TYP6.66.2
1.2 MAX
6X 0.65
8X 0.300.19
2X1.95
0.150.05
(0.15) TYP
0 - 8
0.25GAGE PLANE
0.750.50
A
NOTE 3
3.12.9
BNOTE 4
4.54.3
4221848/A 02/2015
TSSOP - 1.2 mm max heightPW0008ASMALL OUTLINE PACKAGE
NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed 0.15 mm per side. 4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.5. Reference JEDEC registration MO-153, variation AA.
18
0.1 C A B
54
PIN 1 IDAREA
SEATING PLANE
0.1 C
SEE DETAIL A
DETAIL ATYPICAL
SCALE 2.800
www.ti.com
EXAMPLE BOARD LAYOUT
(5.8)
0.05 MAXALL AROUND
0.05 MINALL AROUND
8X (1.5)8X (0.45)
6X (0.65)
(R )TYP
0.05
4221848/A 02/2015
TSSOP - 1.2 mm max heightPW0008ASMALL OUTLINE PACKAGE
SYMM
SYMM
LAND PATTERN EXAMPLESCALE:10X
1
45
8
NOTES: (continued) 6. Publication IPC-7351 may have alternate designs. 7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
METALSOLDER MASKOPENING
NON SOLDER MASKDEFINED
SOLDER MASK DETAILSNOT TO SCALE
SOLDER MASKOPENING
METAL UNDERSOLDER MASK
SOLDER MASKDEFINED
www.ti.com
EXAMPLE STENCIL DESIGN
(5.8)
6X (0.65)
8X (0.45)8X (1.5)
(R ) TYP0.05
4221848/A 02/2015
TSSOP - 1.2 mm max heightPW0008ASMALL OUTLINE PACKAGE
NOTES: (continued) 8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 9. Board assembly site may have different recommendations for stencil design.
SYMM
SYMM
1
45
8
SOLDER PASTE EXAMPLEBASED ON 0.125 mm THICK STENCIL
SCALE:10X
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to itssemiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyersshould obtain the latest relevant information before placing orders and should verify that such information is current and complete.TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integratedcircuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products andservices.Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and isaccompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduceddocumentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statementsdifferent from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for theassociated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designersremain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers havefull and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI productsused in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, withrespect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerousconsequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm andtake appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer willthoroughly test such applications and the functionality of such TI products as used in such applications.TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended toassist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in anyway, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resourcesolely for this purpose and subject to the terms of this Notice.TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TIproducts, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specificallydescribed in the published documentation for a particular TI Resource.Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications thatinclude the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISETO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTYRIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, orother intellectual property right relating to any combination, machine, or process in which TI products or services are used. Informationregarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty orendorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of thethird party, or a license from TI under the patents or other intellectual property of TI.TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES ORREPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TOACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OFMERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUALPROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OFPRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES INCONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEENADVISED OF THE POSSIBILITY OF SUCH DAMAGES.Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, suchproducts are intended to help enable customers to design and create their own applications that meet applicable functional safety standardsand requirements. Using products in an application does not by itself establish any safety features in the application. Designers mustensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products inlife-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., lifesupport, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, allmedical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applicationsand that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatoryrequirements in connection with such selection.Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2017, Texas Instruments Incorporated