ajuste mecanismo z32

SERVICE MANUAL

COPYRIGHT © 2005 Victor Company of Japan, Limited No.YF0812005/9

MECHANISM ASSEMBLYYF08120059

DVC MECHANISM

TABLE OF CONTENTS1 JIGS AND TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-33 PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

1-2 (No.YF081)

SECTION 1JIGS AND TOOLS

1.1 TOOLS REQUIRED FOR ADJUSTMENTS

Fig.1-1-1

1. Torque driverBe sure to use to fastening the mechanism and exterior partsbecause those parts must strictly be controlled for tighteningtorque.Torque setting value of torque driver is limited. At the valuesover the maximum torque setting value, fasten a screwmanually not to damage the screw thread.

2. BitThis bit is slightly longer than those set in conventional torquedrivers.

3. TweezersTo be used for removing and installing parts and wires.

4. Chip IC replacement jigTo be used for replacement of part.

5.Guide driverTo be used for the height adjustment such as the guide rollers.

6. Cleaning clothRecommended cleaning cloth to wipe down the video heads,mechanism (tape transport system), optical lens surface.

Torque driverYTU94088

1. BitYTU94088-003

2.

3. Chip IC replacement jigPTS40844-2

4.TweezersP-895

5. Guide driverYTU94148A-1

6. Cleaning clothKSMM-01

(No.YF081)1-3

SECTION 2SPECIFIC SERVICE INSTRUCTIONS

2.1 DVC MECHANISM2.1.1 Precautions

(1) When fastening parts, pay careful attention to the tighten-ing torque of each screw. Unless otherwise specified, tight-en a screw with the torque of 0.055 N·m (0.56 kgf·cm).

(2) Be sure to disconnect the set from the power supply beforefastening and soldering parts.

(3) When disconnecting/connecting wires, be careful not to getthem and their connectors damaged.

(4) When replacing parts, be very careful neither to damageother parts nor to fit wrong parts by mistake.

2.1.2 Notes on procedure for disassembly/assemblyThe DISASSEMBLY PROCEDURE TABLE shows the proce-dure to disassemble/reassemble mechanism parts.Carefully read the following explanation before starting actualdisassembling/reassembling work. The item numbers(circlednumbers)in the following explanation correspond to those ap-pearing under respective columns of the table.

*1 Numbers appearing in this column indicate the order to re-move parts. When reassembling, follow these numbers inthe reverse order. Circled numbers in this column corre-spond to those appearing in drawings of this section.

*2 This column shows part names corresponding to numbersin the left column.

*3 The symbol (T or B)appearing in this column shows theside which the objective part is mounted on.T =the upper side, B =the lower side

*4 Symbols appearing in this column indicate drawing num-bers.

*5 This column indicates parts and points such as screws,washers,springs,and others to be removed/fitted for disas-sembling/reassembling the mechanism. Besides such theparts, this column occasionally indicates working points.

Example• Remove (W1)=Washer W1.• Remove the solder at (SD1)=Point SD1.• Disconnect A = Connector A.

*6 Numbers in this column represent the numbers of notes inthe text.(For parts that need phase adjustment after reassembling,refer to “MECHANISM ADJUSTMENTS”.)

*7 This column indicates required after-disassembling/-reas-sembling work such as phase adjustment or mechanismadjustment.

NO. PART NAME FIG. POINT NOTE REMARKS

[ 1 ]

[ 2 ]

[ 3 ]

[ 4 ]

[ 5 ]

[ 6 ]

CASSETTE HOUSING ASSY T Fig.2-4-3 3(S1),(L1a)-(L1e) NOTE 1 a,b,c,d ADJUSTMENT

UPPER BASE ASSY T Fig.2-4-4 (S2),(L2a),(L2b) NOTE 2

DRUM ASSY T (S3a),2(S3b) NOTE 3 a,b

REEL DISK ASSY(SUP) T Fig.2-4-5 (W4)

(W5a),(W5b),(W5c)

(W6),(S6a),2(S6b)

NOTE 4 a

REEL DISK ASSY(TU) T NOTE 5 a,b

REEL COVER ASSY T NOTE 6 ADJUSTMENT

*1 *2 *3 *4 *5 *6 *7

Example

P = SpringW = WasherS = Screw* = Lock (L),soldering (SD),shield,connector (CN),etc.

1-4 (No.YF081)

2.1.3 DISASSEMBLY AND ASSEMBLY OF MECHANISM ASSEMBLY2.1.3.1 General statementThe mechanism should be disassembled/assembled in theCASS IN mode (ASSEMBLY mode). (Refer to Fig. 2-1-2,2-1-5.)When the mechanism assembly is removed from the main body,it is generally set in the STOP mode. After the mechanism assembly is removed from the main body,it is required to forcibly supply 3V DC to the LOADING MOTORto unload, and then set the CASS IN mode.<Mechanism assembly/Cassette housing assembly>

Fig.2-1-1

<Back side of the mechanism assembly>

Fig.2-1-2

2.1.3.2 Mechanism modesThe mechanism mode of this model is classified into five modesas shown in Fig. 2-1-9. Each mechanism mode can be distin-guished from others by the relative position of “ ”, “ ”, “ ”marks on the sub cam gear to the inner or outer protrusion on themain deck. Refer to Fig. 2-1-3 to 2-1-8 below.

Fig.2-1-3

Fig.2-1-4

Fig.2-1-5

Fig.2-1-6

Fig.2-1-7

Fig.2-1-8

LOADING MOTOR

DC3V

Back side of deck

CASS IN

HOLE

Half PanchHalf PanchHalf Panch

<MAIN CAM GEAR>

TOP VIEW BOTTOM VIEW

<EJECT mode>

<Confirmation of mode>：HOLE(Penetration)：Half Panch

<CASS IN mode>

<SHORT FF mode>

<STOP mode>

<PLAY mode>

(No.YF081)1-5

2.1.3.3 Mechanism timing chart

Fig.2-1-9

PARTS

MODE

PRESS ARM

T.C. PLATE

TENSION ARM

T5 ARM

SLIDE DECK

S1 ARM

POLE BASE

PINCH ROLLER

PRESS

OFF

EJECT

OFF1

OFF2

ON

LO2

LO1

UL

ON

OFF

LO

UL

PRESS

LO

UL

PRESS

PRESS

SLIDE

OFF

LO

UL

EJECT CAS. IN

CCW

STOP PLAYFWDSHORT

SLIDESTART

TU. P. BEND

SLIDEEND

-46.3o

-6.5o

210.5o

182.8o

204o

204o

204o

204o

204o

244.5o

225.5o

220.2o

204o

127.8o

164.2o

TOUCH

173.6o

TOUCH

TOUCH

69o

3.4o

3.4o

67.2o

67.2o

67.2o

14o

67.2o

67.2o

79.6o

244.5o

a

b

c

ROTARY

ENCODER

MAIN CAM

SUB CAM

-69.2o

273.6o

274.5o

254.5o

210.8o

199.8o

187.8o

260o

(200o)

190o

(149o)(126.9

o)

150o

(193.8o)(164.9

o)

(49.1o)

(63.8o)

(-50o)

(-65o)

195o

70o

91o

0o

0o

-40o

-52o

(260o)

247o

205.3o

78.3o

49.3o

90.3o

101.3o113.3

o

95.8o

5.5o

-5.5o

-49.2o

-68.4o

0o

-54.7o

1-6 (No.YF081)

2.1.4 DISASSEMBLY PROCEDURE TABLEMARK: # After assembly, perform adjustments.

NO. PART NAME FIG. POINT NOTE REMARKS[1] HOUSING ASSY T 1 2(S1),L1a,b,c,d NOTE1a,b ADJUSTMENT[2] DRUM PROTECTOR T 2 S2,L2a,b NOTE2[3] DRUM ASSY T 3(S3),L3a,b NOTE3a,b #[4] REEL COVER ASSY T 2(S4),2(L4a),L4b,c NOTE4[5] IDLER ARM ASSY T 3 - -[6] T5 ARM ASSY T L6a,b NOTE6a,b ADJUSTMENT[7] TENSION ARM ASSY T L7a,S7,L7b,2(L7c) NOTE7a,b,c ADJUSTMENT/#[8] S1 ARM ASSY T L8 NOTE8 ADJUSTMENT[9] SLIDE GUIDE PLATE T 4 S9,L9 NOTE9a,b ADJUSTMENT/#

[10] GUIDE PLATE T S10,L10 - ADJUSTMENT[11] SLIDE DECK ASSY T 2(L11a),3(L11b),2(L11c) NOTE11a,b ADJUSTMENT/#[12] CASSETTE GUIDE T 5-1 S12,2(L12) -[13] PINCH ROLLER ARM ASSY T 5-2 L13 NOTE13a,b,c[14] REEL DISK ASSY (SUP) T L14 NOTE14a,b[15] REEL DISK ASSY (TU) T L15 NOTE15a,b,c[16] BRAKE PLATE T - NOTE16 ADJUSTMENT[17] T. C. PLATE ASSY T 6 L17,SLIDE COLLAR1 NOTE17[18] DRUM BASE T 3(S18),L18a,2(L18b) NOTE18[19] DRIVE ARM ASSY T L19,SLIDE COLLAR2 NOTE19a,b ADJUSTMENT[20] GUIDE RAIL ASSY T 7 S20 NOTE20 ADJUSTMENT/#[21] T5 CATCHER T S21,L21 -[22] CAPSTAN MOTOR T 2(S22) NOTE22[23] REEL PULLEY T - -[24] CENTER GEAR T - -[25] MOTOR BRACKET ASSY T 8 S25 NOTE25a,b,c[26] BELT GUIDE T S26,2(L26) -[27] GEAR COVER T 3(S27),L27a,b,c,d NOTE27 ADJUSTMENT[28] PRESS ARM ASSY T L28 NOTE28 ADJUSTMENT[29] SUB CAM T 9 - NOTE29 PHASE ADJUSTMENT[30] CONNECT GEAR T - NOTE30[31] MAIN CAM T - NOTE31 PHASE ADJUSTMENT[32] ROTARY ENCODER T 10 L32 NOTE32 PHASE ADJUSTMENT[33] LOADING GEAR 1 T - -[34] GUIDE ROLLER (S) ASSY T - NOTE34a,b #[35] COMPRESSION SPRING T - NOTE35[36] MAIN DECK ASSY T - - #

[ 1 ]

(No.YF081)1-7

[25]

[27]

[17]

[ 7 ]

[ 8 ]

[10]

[31]

[12]

[22]

[34] [35] [ 3 ][ 2 ][32] [33] [19] [18] [20] [21]

[14][11] [ 9 ] [ 5 ] [ 4 ] [30]

[36]

[ 6 ]

[26]

[29]

[30]

[28]

[15]

[16]

< TOP VIEW >

[25][22][ 2 ]< BOTTOM VIEW >

[32]

[36]

[11]

[19]

[31]

1-8 (No.YF081)

2.1.5 DISASSEMBLY/ASSEMBLY2.1.5.1 [1] HOUSING ASSYNOTE1a:

When disassembling/ assembling the MECHANISM ASSY,make sure to remove the HOUSING ASSY.When removing the HOUSING ASSY, make sure to bring theHOUSING ASSY up either by changing the mechanism modeto the EJECT mode, or by moving the EJECT LEVER to the di-rection as indicated by the arrow. During the procedure, make sure to return to the CASS INmode if the mode was changed.

NOTE1b:Be careful not to damage the LEFT ARM2,RIGHT ARM2 dur-ing work.

Fig.1

2.1.5.2 [2] DRUM PROTECTOR[3] DRUM ASSY[4] REEL COVER ASSY

NOTE2:During the procedure, be careful in handling the FPC.

NOTE3a:When removing, carefully hold the top center of the DRUMASSY with fingers otherwise it may possibly fall off.

NOTE3b:Pay extra attention to the soil, dust and scratch on the surface.During the procedure, be careful not to cut/ damage the FPC.

NOTE4:During the procedure, remove the LED from the REEL COVERASSY first to set the FPC free, remove the two screws (7, 8),then remove the REEL COVER ASSY by sliding it to the direc-tion as indicated by the arrow.During the procedure, be careful in handling the FPC.

Fig.2

<NOTE1a,b>

LEFT ARM2 RIGHT ARM2

L1a L1b

EJECTLEVER

1(S1)

2(S1)

[ 1 ]

L1cL1d

NOTE1b

NOTE1a

NOTE1b

RIGHTARM2

LEFTARM2

FPC

FPC

LED

LED

< bottom side >

<NOTE3a>

<NOTE2> <NOTE4>

4(S3)

5(S3)

6(S3)

DRUMSIDE

FPC

L2a

L4cL4b

L4aFPC

NOTE4

8(S4)

7(S4)

4(S3) 5

(S3)

6(S3)

[3]

[2]

[4]

NOTE3b

NOTE3a

NOTE2

L3a

L3b

L2b

3(S2)

(No.YF081)1-9

2.1.5.3 [5] IDLER ARM ASSY[6] T5 ARM ASSY[7] TENSION ARM ASSY

NOTE6a:There are two types of the T5 ARM ASSY. They are differentin shape. The old type is without a hook and the new type iswith a hook.When an old type is replaced by a new type, replace thePINCH ROLLER ARM ASSY at the same time as the propercombination of the parts is required.When removing, remove the spring from the hook first if thereis a hook.

NOTE6b:When mounting, pay attention to the correct positioning.

NOTE7a:During the procedure, be careful in handling the TENSIONBAND.

NOTE7b:When mounting, attach the TENSION BAND along the grooveof the gear.

NOTE7c:When mounting, pay attention to the correct positioning.When mounting, attach the TENSION ARM ASSY with theplate moved to the direction as indicated by the arrow.If the plate is moved to the other direction, the TENSIONBAND may break during the operation check as there is toomuch tension. After the mounting, adjust the TENSION ARM ASSY.

2.1.5.4 [8] S1 ARM ASSY[9] SLIDE GUIDE PLATE[10] GUIDE PLATE

NOTE8:When mounting, pay attention to the correct positioning.

NOTE9a:When mounting, pay attention to the correct positioning.

NOTE9b:After attachment, adjust the SLIDE GUIDE PLATE.

Fig.3

Fig.4

L6a

<NOTE6a>

< OLD TYPE > < NEW TYPE >

< FRONT >

< TOP >

<NOTE7b,c>

TENSION BAND

[5]

[6]

L6b

NOTE6b

9(S7)

[7]

TENSION BAND

NOTE7a

NOTE6aL7b

L7a

L7cL7cL7c

11(S10)

10(S9)

[10]

[9][8] L8

NOTE8 NOTE9a,b

L10

L9

1-10 (No.YF081)

2.1.5.5 [11] SLIDE DECK ASSYNOTE11a:

When removing, set the FPC free first.During the procedure, be careful not to cut the FPC.

NOTE11b:During the procedure, be careful in handling.

2.1.5.6 [12]CASSETTE GUIDE[13] PINCH ROLLER ASSY[14] REEL DISK ASSY (SUP)[15] REEL DISK ASSY (TU)[16] BRAKE PLATE

NOTE13a:The spring attachment differs according to the types of the T5 ARMASSY. The spring is attached either to the hook of the SLIDEDECK ASSY or to the hook of the T5 ARM ASSY. When an oldtype is replaced by a new type, replace the T5 ARM ASSY at thesame time as the proper combination of the parts is required.When removing, remove the spring only when the spring is at-tached to the SLIDE DECK ASSY.Be careful when attaching as the spring has been removed ifit was attached to the T5 ARM ASSY.

NOTE13b:During the procedure, be careful in handling.Pay extra attention to the soil, dust and scratch on the ROLLER.

NOTE13c:Be sure to place this part beneath the SLIDE DECK ASSY.

NOTE14a:When removing, be careful not to damage or open too muchthe hook as there is only one hook in a narrow part.

NOTE14b:Be careful not to attach the REEL DISK wrongly. The Supplyside can be identified by the white color at the center.

NOTE 15a:When removing, be careful not to damage or open too muchthe hook as there is only one hook in a narrow part.

NOTE 15b:Be careful not to attach the REEL DISK wrongly. The Take-upside can be identified by the black color at the center.

NOTE 15c:When removing the REEL DISK ASSY, be careful in handlingas the BRAKE PLATE which is located under the REEL DISKASSY becomes free.

NOTE 16:During the procedure, be careful in handling.

Fig.5-1

Fig.5-2

<NOTE11a>

L11aL11c

FPC

T5 CATCHER

L13

<NOTE13a>

< OLD TYPE > < NEW TYPE >

[11]

L11b

L11aNOTE11a

L11b

L11c

FPC

NOTE11bMIC SW

[13]

[15][14] [16]

TENSIONSPRING

L13

NOTE15a,bNOTE16NOTE14a,b

NOTE13b

NOTE13a

NOTE13c

12(S12)

[12] L12

L15L14

WHITE

L14,L15

BLACK

(No.YF081)1-11

2.1.5.7 [17] T. C. PLATE ASSY[18] DRUM BASE[19] DRIVE ARM ASSY

NOTE17:During the procedure, be careful not to lose the SLIDECOLLAR1.

NOTE19a:When mounting, pay attention to the correct positioning.

NOTE19b:During the procedure, be careful not to lose the SLIDECOLLAR2.

Fig.6

2.1.5.8 [20] GUIDE RAIL ASSY[21] T5CATCHER[22] CAPSTAN MOTOR[23] REEL PULLEY[24] CENTER GEAR


NOTE22:When attaching the BELT, place the BELT inside the BELTGUIDE and roll up around the REEL PULLEY.

Fig.7

L18a

L19

<NOTE19a>

13(S18)

14(S18)

15(S18)

SLIDE COLLAR2

SLIDE COLLAR1

[17]

[18]

[19]

L17

L18a

L18b

L19

NOTE17

NOTE19a

NOTE19b

<NOTE22><NOTE20>

REELPULLEY

BELT GUIDE

16(S20)

17(S21)

18(S22)

19(S22)

[20]

[21]

[22]

[23][24]

L21

NOTE22

NOTE20

BELT

1-12 (No.YF081)

2.1.5.9 [25] MOTOR BRACKET ASSY[26] BELT GUIDE[27] GEAR COVER[28] PRESS ARM ASSY

NOTE25a:When disassembling, remove the four solder points (SD25) onthe ROTARY ENCODER as the MOTOR BRACKET ASSYand the ROTARY ENCODER are soldered together to oneFPC.

NOTE25b:During the procedure, be careful in handling the FPC. Pay at-tention not to leave finger prints etc. on the surface of the DEWsensor.

NOTE25c:During the procedure, be careful with the WORM WHEELwhich is attached inside.When mounting, attach the WORM WHEEL to the MOTORBRACKET ASSY before mounting to the MECHANISM DECKASSY.

NOTE27:When removing, remove the three screws (22-24), turn theGEAR COVER anticlockwise by lifting up the parts with brokenlines. Remove L27b,c and slide the GEAR COVER by sliding to thedirection shown with arrows. When mounting, pay attention to the correct positioning.

NOTE28:When mounting, pay attention to the correct positioning. Fig.8

GEAR COVER

PRESSARMASSY

L27aL27b

L27cL27d

SD25BOTTOMSIDE

MOTORBRACKETSIDE

FPC

<NOTE25a> <NOTE25c>

<NOTE27>

NOTE27

NOTE28

20(S25)

21(S26)

22(S27)

23(S27)

24(S27)

[25]

[27]

[28]

L27d

L27cL27b

L28

NOTE25a,b,cNOTE25c

NOTE25b

[26]L26

WORM WHEEL

DEW SENSOR

L27a

(No.YF081)1-13

2.1.5.10 [29] SUB CAM[30] CONNECT GEAR[31] MAIN CAM


NOTE30:When mounting, make sure to confirm the correct positioningof the MAIN CAM, the SUB CAM, and the left and right GEARbefore attachment. Although the positioning adjustment of theCONNECT GEAR itself is not necessary, the alignment of theleft and right GEARs is very important.


2.1.5.11 [32] ROTARY ENCODER[33] LOADING GEAR 1[34] GUIDE ROLLER (S) ASSY[35] COMPRESSION SPRING[36] MAIN DECK ASSY


NOTE34a:During the procedure, be careful in handling.Pay extra attention to the soil, dust and scratch on the ROLLER.

NOTE34b:Be sure to perform rough adjustment if the height of the GUIDEROLLER (S) ASSY has been adjusted during the procedure. Otherwise the tape will be damaged when it is run. For the rough adjustment, fully tighten up the GUIDE ROLLER(S) ASSY clockwise then rewind it 1.5 revolutions. The guide measurement for the height is 17.1mm.

NOTE35:During the procedure,be caraful not to lose any parts.

Fig.9

Fig.10

<NOTE30>

<NOTE29><NOTE31>

LOADINGGEAR

MAIN CAMSUBCAM

NOTE31

17.1mm

<NOTE32> <NOTE34b>

[29]

[30]

[31]NOTE31

NOTE29

[32]

[33]

[34] [35]

[36]

L32

NOTE35NOTE34a,b

NOTE32

1-14 (No.YF081)

2.1.6 Mechanism adjustment 1. SLIDE GUIDE PLATE adjustment

This adjustment is required when the SLIDE DECK ASSEM-BLY is removed from the MAIN DECK ASSEMBLY. The adjustment is also required when the SLIDE GUIDEPLATE is removed. Refer to the Fig2-1-6-1unless otherwise instructed.

Adjustment procedure(1) Set the PLAY mode while the HOUSING ASSEM-

BLY is removed. Refer to the Fig. 2-1-8.(2) Loosen the screw A.(3) Press both the MAIN DECK ASSEMBLY/ SLIDE

DECK ASSEMBLY inward with an even power fromboth left and right. Fully pull up the SLIDE GUIDEPLATE to the left and tighten the screw A.

NOTE:When pressing the SLIDE DECK ASSEMBLY,press near the screw hole for the HOUSING AS-SEMBLY attachment. Avoid pressing the sensor asit is fragile.

NOTE:The tightening torque is 0.078N•m(0.8kgf•cm)

(4) Perform an operation check.

NOTE:Repeat the operation check of unloading/ loading toconfirm the smooth and steady slide movementwithout any jam or rattle.

2. Tension Arm Assembly adjustmentThis adjustment is required when the Tension Arm Assem-bly is replaced. Refer to the Fig.2-1-6-2unless otherwise instructed.

Adjustment procedure(1) Set the Play mode while the Housing Assembly is

removed. Refer to the Fig. 2-1-8.(2) Loosen the screw B.(3) Slide the Guide Plate up and down to set the tip of

the Tension Arm Assembly to the edge of the screwgroove, and tighten the screw B. • The tightening torque is 0.049N•m(0.5kgf•cm)

(4) Perform an operation check.

NOTE:Repeat loading and unloading, and make sure tocheck that the top of the TENSION ARM and theedge match properly when observed from thestraight above.

NOTE:The adjustable range is ±0.25mm from the edge.

Fig.2-1-6-1

Fig.2-1-6-2

<NOTE>

0.5mmEDGE

TENSION ARMTENSION ARMASSYASSY

TENSION ARMASSY

Screw A

SLIDEGUIDEPLATE

MAIN DECK ASSY

SENSOR

( 0.25mm)EDGE

MAIN DECK ASSY

SENSOR

TENSIONARMASSY

Screw B

(No.YF081)1-15

2.1.7 REMARKS2.1.7.1 Cleaning

(1) For cleaning of the upper drum (particularly video heads),use fine-woven cotton cloth with alcohol soaks through. Donot move the cloth but turn the upper drum counterclock-wise.

NOTE:Make sure not to move the cloth in the vertical direction to the video head, since it may cause damage of the videoheads.

(2) For cleaning of parts of the tape transport system exceptthe upper drum, use fine-woven cotton cloth or cotton swabsoaked alcohol.

(3) After cleaning, confirm that the cleaned parts are complete-ly dry before loading the deck with cassette tape.

2.1.7.2 Applying oil and grease(1) Periodical oiling and greasing are not required but should

be done to new parts when replacing. If oil and grease onthe other parts of the other party are old and dirty, wipethem clean and apply new oil or grease.

(2) For parts and points to apply oil and grease, refer to thePARTS LIST. Fig.2-1-7 specifies oil and grease to be used.

(3) When oiling, clean the objective parts with alcohol first andapply one or two drop(s) of oil. Too much oiling causes ro-tary parts to slip because of oil leakage.

specifies oil and grease to be usedFig.2-1-7

Classification Part No. Symbol in drawing

Grease KYODO-SH-JB AA

Oil YTU94027 BB

Grease (HANARL) RX-410R CC

1-16 (No.YF081)

2.1.8 SERVICE NOTEUse the following chart to manage mechanism parts that are removed for disassembling the mechanism.

Fig.2-1-8-1

HOUSING ASSY DRUM ASSY

REEL COVER ASSY IDLER ARM ASSY T5 ARM ASSY

CASSETTE

GUIDE

TENSION ARM ASSY

SLIDE DECK ASSY PINCH ROLLER

ASSY

REEL DISK ASSY

(SUP : WHITE)

REEL DISK ASSY

(TU : BLACK)

BRAKE PLATE

SLIDE GUIDE PLATE GUIDE PLATES1 ARM ASSY

[ 3 ]DRUM PROTECTOR[ 2 ]

[ 4 ]

[ 7 ]

[ 9 ]

[ 5 ] [ 6 ]

[ 12 ][ 10 ]

[ 11 ] [ 13 ] [ 14 ]

[ 15 ] [ 16 ]

[ 8 ]

[ 1 ]

Fig

.5-1

Fig

.4

Fig

.3

Fig

.2F

ig.1

Fig

.2

Fig

.5-2

Fig

.5-2

(NEW TYPE)(OLD TYPE)

or

(No.YF081)1-17

Fig.2-1-8-2

[ 29 ]

[ 30]

[ 31 ]

[ 17 ] [ 20]

[ 21 ]

[ 22 ] [ 23 ]

[ 24 ]

[ 25 ] [ 27 ] [ 28 ]

[ 36 ]

[ 32 ] [ 33 ] [ 34 ]

[ 26 ]

[ 18 ]

[ 19 ]

Fig

.6

Fig

.7F

ig.8

Fig

.9

Fig

.10

T.C.PLATE ASSY GUIDE RAIL

ASSY

CAPSTAN MOTOR REEL PULLEY

CENTER GEAR

T5 CATCHER

BELT GUIDE

GEAR COVER PRESS ARM

ASSY

DRUM ASSY

DRIVE ARM ASSY

SUB CAM ROTARY

ENCODER

MAIN DECK ASSY

LOADING

GEAR1

GUIDE ROLLER(S) ASSY

COMPRESSION SPRING

MAIN CAM

CONNECT GEAR

MOTOR

BRACKET ASSY

[ 35 ]

SLIDECOLLAR2

SLIDECOLLAR1

WORM

WHEEL

1-18 (No.YF081)

2.1.9 SERVICE NOTE 2Use the following chart to manage screws.

Fig.2-1-7

Sym

bo

l N

o.

Re

mo

vin

g o

rde

r o

f scre

w

Pla

ce to s

tick s

cre

w

Re

fere

nce

dra

win

g (

Fig

.No

.)

Scre

w tig

hte

nin

g torq

ue

Sym

bo

l N

o.

Re

mo

vin

g o

rde

r o

f scre

w

Pla

ce to s

tick s

cre

w

Re

fere

nce

dra

win

g (

Fig

.No

.)

Scre

w tig

hte

nin

g torq

ue

NO

TE

:

Pa

y c

are

ful a

tte

ntio

n t

o t

igh

ten

ing

to

rqu

e f

or

ea

ch

scre

w.

To

rqu

e s

ett

ing

va

lue

of

torq

ue

drive

r is

lim

ite

d.

At

the

va

lue

s o

ve

r th

e m

axim

um

to

rqu

e s

ett

ing

va

lue

,

fa

ste

n a

scre

w m

an

ua

lly n

ot

to d

am

ag

e t

he

scre

w t

hre

ad

.

a 0

.04

9N

m (

0.5

kgf

cm

)b

0.0

39

Nm

(0.4

kgf

cm

)c

0.0

78

Nm

(0.8

kgf

cm

)

Th

e t

igh

ten

ing

to

rqu

e o

f th

e N

o.1

0 s

cre

w is 0

.04

9N

m(0

.5kg

fcm

) fo

r m

ou

ntin

g,

an

d 0

.07

8N

m(0

.8kg

fcm

) fo

r a

dju

stm

en

t.

F

or

de

tails

, re

fer

to t

he

ad

justm

en

t ite

m "

2.1

.6.1

Ad

justm

en

t o

f th

e S

LID

E G

UID

E P

LA

TE

"

[1]

[3]

[2]

[4]

[5]

[6]

[16

][1

7]

[20

][2

2]

[23

][2

4]

[25

][2

6]

[27

][2

8]

[29

][3

0]

[31

][3

2]

[33

][3

4]

[35

][3

6]

[21

]

12

34

56

78

- -

- -

-

10

--

9- -

11

12

21

20

22

23

24

- - -

- -

- -

- -

- -

- -

16

17

18

19

- -

- -

-

- -

- -

-

- -

-- -

-

- -

- -

- -

- -

[7]

[8]

[9]

[10

][1

1]

[12

][1

3]

[14

][1

5]

Fig

.1

Fig

.7F

ig.8

Fig

.9F

ig.1

0

Fig

.2F

ig.3

Fig

.4F

ig.5

-2Fi

g.5-

1F

ig.6

[18

][1

9]

13

14

15

- - -a

a

aa

ba

/cb

bb

ab

(No.YF081)1-19

(No.YF081)

AV & MULTIMEDIA COMPANY CAMCORDER CATEGORY 12, 3-chome, Moriya-cho, kanagawa-ku, Yokohama, kanagawa-prefecture, 221-8528, JapanVictor Company of Japan, Limited

VPTPrinted in Japan

ajuste mecanismo z32

Documents