alr3014 - scene7

MADE IN BRITAIN

Dimensions

Width - 104cm

Depth - 49.5cm

Height - 171cm

New Sywell - 4 Drawer 3 Door RobeAssembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 4 - 07/10/14

Important - Please read these instructions fully before starting assembly

ALR3014

282/7023

258/1376

281/6096

278/9130

Issue 2 - 08/04/14. Drawer box sizes increased.Add 8 wedges.Add 4 plastinails.

Issue 3 - 08/09/14 - Round Back Holders replaced with Oblong Back Holders.

Issue 4 - 07/10/14 - The size of the Drawer Front has been changed from 164mm to 162mm.

Safety and Care AdviceImportant - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 73kgs.Please lift with care.

• Check you have all thecomponents and tools listed on pages 1, 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your localauthority waste disposal centre.

• We do notrecommend the use of power drill/drivers for inserting screws,

as this could damage the unit.Only use hand screwdrivers.

• Safety note: It isrecommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Components - PanelsPlease check you have all the panels listed below

If you have damaged or missing components, call the Customer Helpline: 08456 400800 quoting the reference numbers below

1 4

5

3

7

2

6

8

1

Drawer Front (D2575A)(333 x 162mm) x 4

Drawer Base (T315-367)(315 x 367mm) x 4

Drawer Back (W304-124)(304 x 124mm) x 4

Left Drawer Side (W370-124LH)(370 x 124mm) x 4

Right Drawer Side (W370-124RH)(370 x 124mm) x 4

Rail (D2598A)(322 x 125mm)

Horizontal (D2573A)(337 x 467mm)

Shelf (D2574A)(322 x 468mm) x 3

Components - PanelsPlease check you have all the panels listed below

2

9 10

80%


Left Side (D2560A)(1711 x 496mm)

Right Side (D2569A)(1711 x 496mm)

Hanging Rail (FHR666)(666mm long)

12

Top (D2568A)(1011 x 494mm)

Base (D2570A)(1011 x 494mm)

Upright (D2571A)(1656 x 468mm)

Large Door (D2563A)(1650 x 333mm) x 2

Centre Door (D2576A)(990 x 333mm)

Small Back (X1682-340)(1682 x 340mm)

Large Back (X1682-694)(1682 x 694mm)

11

13

14

15 Divider (D2572A)(675 x 468mm)

17

16

18 19

Please check you have all the fittings listed below

3

Components - FittingsIf you have damaged or missing components, call the Customer Helpline: 08456 400800 quoting the reference numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

A

Wooden dowel (F22) x 20

B

Metal dowel (F901) x 28

C

D E F

G H I

L

M

J K

9mm Screw (F74) x 8 9mm Screw (F73) x 16

P

Drawer runner (F1004) x 8

13mm Screw (F79) x 1

Small locking nut (F3) x 8

Large locking nut (F900) x 20

Nail (F51) x 37

Bracket (F327) x 1 Handle (F315) x 713mm Screw (F63) x 20

ON

Hinge plate (F523) x 8 Hinge (F522) x 8

Q


R

Rail Holder (F891) x 2

S

Nail screw (F277) x 5

Shelf stud (F110) x 12

V

Foot (F854) x 1


Knock-in Peg (F171) x 16

U X

Plastic Nail (F91) x 4

W

Wedgefix (F639) x 8

T

Back holder (F276) x 5

These can also be round

Assembly Instructions

4


Step 1

x 4 x 4

x 4

B

Prepare the 4 drawer fronts

Screw 2 metal dowels into the holes shown on the back of each drawer front .

Note: Tighten the metal dowels up fully against the panels.

B

1

Prepare the drawer sides

Insert a small lockingnut into the hole shown on the left drawer side and right drawer side .

Note: Arrow on locking nut must point towards hole in edge of panel.

E

4

5

Step 2

Step 3

B

B

1

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

Attach the drawer sides to the drawer front

Push the left drawer side . and right drawer side . onto the back of the drawer front .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

45

1

E45

x 4

E

Note: The locking nuts can be on either surface of the drawer sides.Make sure that the small groove is on the inside, as shown.

E

BB

E

Small groove

9

E E

4 5

5

1

4


5

Step 4

Step 5

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .

3

4 5

1

Fit the drawer back

Fit the drawer back down onto the drawer base .

Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

2

3

3

2

2

U

4 5

Attach the handles

Attach a handle to each drawer front using 2 screws .

L

F

Step 6

1

3

5

4

2

U

U

x 4U

U

x 41

F

F

L

x 4

Step 7

Fit the wedgefixes

Turn the drawerassemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

W

WW W

I

x 4

3 5

4

1

A

A


6

Step 8

Prepare the upright

a: Place 4 runners on the upright . Slide back the top of the runner and use the 2nd hole from the front to fit the 1st screw .

To fit the rail holder , screw through the top hole with screw and into the mark hole drilled in the upright . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

b: Slide the runner back the other way and fit the 2nd screw into the corresponding hole in the upright .

Fit 2 hinge plates onto the upright , making sure that the slot is facing towards the finished front edge.

c: Tap 4 wooden dowels into the upright .

Screw 2 metal dowels into the upright .

Insert 4 large lockingnuts into theupright .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

P11

I

R

J

11

PP

PPI

II

I

II

II

B

B

D

D

D

D

N

N

N

J

R

J

A

A

J

R

J

R

Finished front edge

Finished front edge

Finished front edge

Fini

shed

front

edg

eI

P

a:

b:

c:

J

P

11

11

I

11

11

11

N

A11

11

11 10mm

A

D

B

D

Finished front edge

Finished front edge


7

Step 9

Prepare the base

Tap 4 wooden dowels into the base .

Screw 2 metal dowels into the base .

Insert 4 large lockingnuts into the base .

Step 6

Finishedfront edge

I

PI

P

I

P

I

P

I

P

II

II

B

D

B

D

B

A

A

Prepare the divider

a: Place 4 runners on the divider . Slide back the top of the runner and use the 2nd hole from the front to fit the 1st screw .

b: Slide the runner back the other way and fit the 2nd screw into the corresponding hole in the divider .

c: Tap 2 wooden dowels into the divider .

Screw 2 metal dowels into the divider .

Insert 2 large lockingnuts into thedivider .

Turn the divider over

d: Screw a metal dowel . into the divider .

P15

I

P

15

15

15

I

Turn the divider over

A

B

D15

Finished front edge

Finished front edge

15B

a:

b:

c:

d:

15

15

15

15

Finished front edge


8

Step 10

A

A

Finished front edge

Plain chipboard surface

D

D

D

D

A

A

Prepare the horizontal

Tap 4 wooden dowels into the horizontal .

Insert 4 large lockingnuts into thehorizontal .

A8

D8

8

Finished front edge

Finished front edge

Step 11

Fit the horizontal to the upright

Push the horizontal onto the upright . Use a screwdriver to tighten the 2 large locking nuts fitted to the horizontal .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

Step 12

Fit the divider to the horizontal

Push the divider onto the horizontal . Use a screwdriver to tighten the 2 large locking nuts fitted to the horizontal .

811

11D

158

8D

D

B

D

8

11

8

15

Finished front edge


9

Step 13

Step 14

A

APrepare the base

a: Tap 4 wooden dowels into the base . .

Insert 4 large lockingnuts into the base .

Screw the foot into the middle of the base , 75mm in from the front edge using screw .

Turn the base over

b: Screw 4 metal dowels into the base . .

A14

D 14

D

D

C

V

A

A

Finished front edge

75mm

D

DPlain chipboard

surface

14

Finished front edge

B

BB

B

14

Turn the base over

a:

b:

14B

Fit the base

Push the base onto the upright and divider . Use a screwdriver to tighten the 4 large locking nuts fitted to the upright and the divider .

1411

D

14

15

11

15

1115

Note: To make it easier to fit the top and base panels, placepolystyrene blocks from the packagingunderneath the upright and divider panels to raise the assembly.

V14

C

Finished front edge


10

Step 15

Finished front edge

A

A

D

D

A

A

D

D B

BPrepare the top

a: Tap 4 wooden dowels into the top .

Insert 4 large lockingnuts into the top .

Screw 2 metal dowels into the top .

A 13

D 13

13B

13

Step 16

Fit the top

Push the top onto the upright . Use a screwdriver to tighten the 2 large locking nuts fittedto the upright .

1311

D11

13

11

Step 17

B

B

B

BN

N

NFinished

front edge

Prepare the right side

Screw 4 metal dowels into the right side .

Fit 3 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.

B10

N10

10

N


11

Step 18

Fit the right side

Push the right side onto the top and base . Use a screwdriver to tighten the 4 large locking nuts fittedto the top andbase .

Step 19

Finished front edge

Prepare the left side

Screw 5 metal dowels into the left side .

Fit 3 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.

To fit the rail holder , screw through the top hole with screw and into the mark hole drilled in the left side . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

B9

N

N

N

N

B

B

B

B

B

J

R

J

9

N9

R

J

9

J

1310

14

1013

14

D13

14

A


12

Step 20

Prepare the rail

Tap 2 wooden dowels into the rail .

Insert 2 large lockingnuts into the rail .

Step 21

D

A

D

Plain chipboard surface

6

A

D

6

6

Fit the rail

Push the rail onto the divider . Use a screwdriver to tighten the large locking nut fitted to the rail .

6

6

15

D

6

15

Note: Support the rail until the left side has been fitted in the next step.

y

x

y

yy


13

Step 22

Step 23

13

14

Finished front edge

9

6

Fit the left side

Push the left side onto the assembly. Use a screwdriver to tighten the 5 large locking nuts fitted to the top , base and rail .

9

D13 146

The measurement from top corner X to bottom corner X must be equal to the measurement from top corner Y to bottom corner Ya:

Fit the back panels

a: Square up the unit by making sure that measurement x:x equals y:y.

Place the small back and large back down onto the unit as shown.

Make sure that the 2 backs are pushed up tight against each other and that they meet over the back edgeof the upright.

b: Nail aroundthe outside edgesof the 2 backs.

Note: Do not nail where the backs meet. Nails should be spaced about 150mm apart.

1819

M

Note: Do not nail where the backs meet.

b:M

18

19

x

Tap 2 plastic nails into the bottom edge of each of the sides and . .

X

910

9

X

X

10

X

X


14

Step 24

Step 25

18

19

Secure the backs

Tap the nail screws through the back holders . and down between the backs and into the back edgeof the divider.

Keep tapping the nail screws in until the back holders dig into the small and large back.

Stand the unit up for the next step.

S

T18 19

S

T

TS + x 5

Warning: The unit is heavy. Lift with care.

Fit the hanging rail and the drawers

Starting with the bottom drawer, slide both the runners forward and locate the drawersides and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .

Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner.

Note: Do not overtighten the screws .If they catch on the runner you may need to loosen them slightly.

H

P

P

4 5

H

2nd threaded hole

P

H

HH

S

T

T

Note: These can also be round


15

Step 26

Step 27

Q x 4

Q x 4

Q x 4

Fit the shelf studs

For each of the 3shelves , insert 4 shelf studs at the desired height.

Q7

Fit the shelves

Lower the 3 shelves down onto the shelf studs .Q

77

7

7


16

Step 28

12

12

R

Fit the hanging rail

Push the hanging rail into the rail holders fitted to the side panels.

12R

Step 29

Prepare the 3 doors

Push fit 3 hinges into the centre door and each of the large doors . .

Secure each hinge with2 screws .

Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.

J

O16

17

90O

O

JJ

O

JJ

O

JJ

17

x 2

O

JJ

O

JJ

16

L17


17

Step 30

Fit doors and handles

Note: The easiest way to attach each door and . is to fit the top hinge first, then align and fit the other hinges.

a: Push the hinge onto the front part of the hinge plate .The recess at the bottom of screw B goes into the slot in the hinge plate.

b: Keep the hinge FLAT against the hinge plate as you slide it across as far as it will go.Tighten screw A.

c: The hinge must be flat against the hinge plate prior to anyadjustment.

d: The hinge must NOT be AT AN ANGLE to the hinge plate when assembled.This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure.Remove the hinge from the hinge plate and then re-assemble being careful to followinstructions a-c.

e: Attach a handle to each door and using 2 screws .

O

O

O

N

N

N

O

N

L

F

1617

16 17

a: b:

c: d:

N

O

N

N

B

N

O

O

O

A

O

N

B

e:

FF

17

16

L

L


18

Step 31

b:

c:

d:

a:Adjust the doors if needed

a: Before adjusting the doors, use a spirit level to check the base (or top) of the unit is level, front-to-back andside-to-side in the 3 positions shown.Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.

b: Height adjustment.Loosen screws A on hinge plates and move door up or down as required.Retighten screw A.

c: Forward and Back adjustment.Loosen screw B on hinge plate and move door in or out as required.Retighten screw B.

d: Sidewaysadjustment.To move door ‘out’ loosen screw C.To move door ‘in’ tighten screw C.

A

A

B

C


19

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800and quote the reference numbers on the component pages.Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

ALR3014

Step 32

Top of UnitWALL

WALL

Back of U

nit

Fit the bracket

To prevent possible overbalancing, werecommend that this unit is secured to a suitable wall by use of the bracket fitted to the top of the unit.

Fixings are not supplied, as they will need to suit the wall type and the length of screw will depend on the distance from the back of the unit to the wall.

Fix the bracket loosely onto the top of the unit using screw and mark the wall for the wall fixing.

Swivel the bracket away from the wall and drill a hole in the wall using a suitable drill bit and fit your wall fixing.

Swivel the bracket back and fix the bracket to the wall, then tighten screw .

Note: Take care when drilling the wall that you do not drill into any pipes, wires etc.If in doubt, consult an expert.

Warning: The unit is heavy. Lift with care.

Assembly is complete

K

K

G

K

K

G

K

K

G

K

alr3014 - scene7

Documents