ambiq micro apollo series - fujitsu · the sk-amap1-breakout-v11 evaluation board includes an ambiq...
TRANSCRIPT
Fujitsu Electronics Europe Factsheet
AMBIQ MICRO APOLLO SERIES ARM CORTEX M4 MICROCONTROLLER
FEEU APOLLO EVALUATION PLATFORM
FEEU APOLLO EVALUATION PLATFORM Factsheet
FEEU APOLLO EVALUATION PLATFORM - 2 - © Fujitsu Electronics Europe GmbH
Introduction
The Fujitsu Apollo Evaluation Platform compatible with Ambiq Micro Apollo 1 or Apollo 2. The platform consists of two parts: The breakout board and the base board. The breakout boards for Apollo 1 and Apollo 2 are pin-compatible.,Only jumper settings need adjustment to setup the base board for Apollo 1 or Apollo 2 usage. Both parts can easily plug together:
FEEU APOLLO EVALUATION PLATFORM Introduction
© Fujitsu Electronics Europe GmbH - 3 - FEEU APOLLO EVALUATION PLATFORM
The Fujitsu Apollo Evaluation Platform includes a nano/micro power/energy measurement probe to enable easy power measurement via PC without the need of an expensive multi-meter or power probe. The on-board CMSIS-DAP compatible debugger works driverless with common toolchains like IAR Workbench or ARM/Keil µVision, but is also supported by a free-of-charge toolchain iSystem WinIDEA Open. For additional communication to the PC, the on-board CMSIS-DAP compatible chip “Fujitsu D-Bug” supports USB to UART conversion.
The Fujitsu Evaluation Platform includes additional software examples (based on MCU templates) to the Ambiq Micro’s SDK. It offers MCU Templates as a kind of a common project framework or software framework needed for developers to have an easy start in development with MCUs. Following IDEs are supported:
ARM (Keil μVision) Atollic (Atollic TrueStudio) Eclipse emIDE
iSYSTEM WinIDEA Open IAR (IAR Embedded Workbench
for ARM Cortex M) Makefile (GNU)
FEEU APOLLO EVALUATION PLATFORM Factsheet
FEEU APOLLO EVALUATION PLATFORM - 4 - © Fujitsu Electronics Europe GmbH
1.1 The base board SK-AMAPOLLO-BASE-V11
The SK-AMAPOLLO-BASE-V11 evaluation board includes a low-cost evaluation board usable with FEEUs Ambiq Micro Apollo break-out boards SK-AMAP1-BREAKOUT-V11 (Apollo 1) and SK-AMAP2-BREAKOUT-V11 (Apollo 2).
1.1.1 Features
- Socket for SK-AMAP1-BREAKOUT-V11 / SK-AMAP2-BREAKOUT-V11 - Arduino UNO compatible pin headers - 2 user push buttons - 1 reset button - 1 RGB LED - On-Board USB Debugger Fujitsu D-Bug:
o CMSIS-DAP compatible debugger o Additional UART channel o Nano power measurement
- Power via DC connector - Power via USB - On-Board 3.3V voltage regulator
1.1.2 Dimensions
- Width: 68.6mm - Height: 53.3mm
1.1.3 Scope of delivery
- Apollo base–board SK-AMAPOLLO-BASE-V11 in ESD bag - USB-Mico cable
Not scope of delivery: SK-AMAP1-BREAKOUT-V11 / SK-AMAP2-BREAKOUT-V11
59€ at shop.feeu.com
FEEU APOLLO EVALUATION PLATFORM Introduction
© Fujitsu Electronics Europe GmbH - 5 - FEEU APOLLO EVALUATION PLATFORM
1.2 The Apollo 1 breakout board SK-AMAP1-BREAKOUT-V11
The SK-AMAP1-BREAKOUT-V11 evaluation board includes an Ambiq Micro Apollo 1 MCU with all pins available at 54 pins.
1.2.1 Features
- Ambiq Micro Apollo 1: o Ultra-low active mode power consumption: 35µA/MHz (executing from Flash) o Ultra-low sleep mode power consumption: 143nA (with RTC on) o High-performance, 32-bit ARM Cortex-M4F processor
Up to 24MHz clock frequency Floating point unit Wake-up interrupt controller with 12 interrupts
o Ultra-low power memory Up to 512kB Flash Up to 64kB low-leakage RAM
o Ultra-low power interface for off-chip sensors 10-bit, 13-channel, 1MS/s ADC Temperature sensor with ±4°C accuracy
o Rich set of timing peripherals o Flexible serial peripherals
I2C/SPI master for communication with external peripherals I2C/SPI slave for optional host communications UART for communication with peripherals and legacy devices
o Wide operating range: 1.8 to 3.8V o Compact package options
64-pin BGA with 50 GPIO 41-pin CSP with 27 GPIO
- Parts assembled: o MCU o Passives o Crystal o DC/DC converter coils o Reset button o SWD Debug header o 2x 27 pin headers 2.54mm o 1x 10 pin communication header
1.2.2 Dimensions
- Width: 22mm - Height: 70mm
1.2.3 Scope of delivery
- Apollo 1 breakout board SK-AMAP1-BREAKOUT-V11 in ESD bag
19€ at shop.feeu.com
FEEU APOLLO EVALUATION PLATFORM Factsheet
FEEU APOLLO EVALUATION PLATFORM - 6 - © Fujitsu Electronics Europe GmbH
1.3 The Apollo 2 breakout board SK-AMAP2-BREAKOUT-V11
The SK-AMAP2-BREAKOUT-V11 evaluation board includes an Ambiq Micro Apollo 2 MCU with all pins available at 54 pins.
1.3.1 Features
- Ambiq Micro Apollo 2: o Ultra-low supply current:
<10 μA/MHz executing from flash at 3.3 V <10 μA/MHz executing from RAM at 3.3 V
o High-performance ARM Cortex-M4F Processor: Up to 48 MHz clock frequency Floating point unit Memory protection unit Wake-up interrupt controller with 32 interrupts
o Ultra-low power memory: Up to 1 MB of flash memory for code/data Up to 256 KB of low leakage RAM for code/data 16kB 2-way Associative Cache
o Ultra-low power interface for off-chip sensors: 14 bit, 15-channel, up to 1.2 MS/s ADC Temperature sensor with +/-3ºC accuracy Voltage Comparator
o Flexible serial peripherals: 6x I2C/SPI master for communication with sensors, radios, and other
peripherals 1x I2C/SPI slave for host communications 2x UART for communication with peripherals and legacy devices
o PDM for mono and stereo audio microphones o Rich set of clock sources:
32.768 kHz XTAL oscillator Low frequency RC oscillator – 1.024 kHz High frequency RC oscillator – 48 MHz
o RTC based on Ambiq’s AM08X5/18X5 families o Compact package options:
2.5 x 2.5 mm (0.35mm) 49-pin CSP with 34 GPIO 4.5 x 4.5 mm (0.5mm) 64-pin BGA with 50 GPIO
- Parts assembled: o MCU o Passives o Crystal o DC/DC converter coils o Reset button o SWD Debug header o 2x 27 pin headers 2.54mm o 1x 10 pin communication header
19€ at shop.feeu.com
FEEU APOLLO EVALUATION PLATFORM Introduction
© Fujitsu Electronics Europe GmbH - 7 - FEEU APOLLO EVALUATION PLATFORM
1.3.2 Dimensions
- Width: 22mm - Height: 70mm
1.3.3 Scope of delivery
- Apollo 2 breakout board SK-AMAP2-BREAKOUT-V11 in ESD bag