Fujitsu Electronics Europe Factsheet
AMBIQ MICRO APOLLO SERIES ARM CORTEX M4 MICROCONTROLLER
FEEU APOLLO EVALUATION PLATFORM
FEEU APOLLO EVALUATION PLATFORM Factsheet
FEEU APOLLO EVALUATION PLATFORM - 2 - © Fujitsu Electronics Europe GmbH
Introduction
The Fujitsu Apollo Evaluation Platform compatible with Ambiq Micro Apollo 1 or Apollo 2. The platform consists of two parts: The breakout board and the base board. The breakout boards for Apollo 1 and Apollo 2 are pin-compatible.,Only jumper settings need adjustment to setup the base board for Apollo 1 or Apollo 2 usage. Both parts can easily plug together:
FEEU APOLLO EVALUATION PLATFORM Introduction
© Fujitsu Electronics Europe GmbH - 3 - FEEU APOLLO EVALUATION PLATFORM
The Fujitsu Apollo Evaluation Platform includes a nano/micro power/energy measurement probe to enable easy power measurement via PC without the need of an expensive multi-meter or power probe. The on-board CMSIS-DAP compatible debugger works driverless with common toolchains like IAR Workbench or ARM/Keil µVision, but is also supported by a free-of-charge toolchain iSystem WinIDEA Open. For additional communication to the PC, the on-board CMSIS-DAP compatible chip “Fujitsu D-Bug” supports USB to UART conversion.
The Fujitsu Evaluation Platform includes additional software examples (based on MCU templates) to the Ambiq Micro’s SDK. It offers MCU Templates as a kind of a common project framework or software framework needed for developers to have an easy start in development with MCUs. Following IDEs are supported:
ARM (Keil μVision) Atollic (Atollic TrueStudio) Eclipse emIDE
iSYSTEM WinIDEA Open IAR (IAR Embedded Workbench
for ARM Cortex M) Makefile (GNU)
FEEU APOLLO EVALUATION PLATFORM Factsheet
FEEU APOLLO EVALUATION PLATFORM - 4 - © Fujitsu Electronics Europe GmbH
1.1 The base board SK-AMAPOLLO-BASE-V11
The SK-AMAPOLLO-BASE-V11 evaluation board includes a low-cost evaluation board usable with FEEUs Ambiq Micro Apollo break-out boards SK-AMAP1-BREAKOUT-V11 (Apollo 1) and SK-AMAP2-BREAKOUT-V11 (Apollo 2).
1.1.1 Features
- Socket for SK-AMAP1-BREAKOUT-V11 / SK-AMAP2-BREAKOUT-V11 - Arduino UNO compatible pin headers - 2 user push buttons - 1 reset button - 1 RGB LED - On-Board USB Debugger Fujitsu D-Bug:
o CMSIS-DAP compatible debugger o Additional UART channel o Nano power measurement
- Power via DC connector - Power via USB - On-Board 3.3V voltage regulator
1.1.2 Dimensions
- Width: 68.6mm - Height: 53.3mm
1.1.3 Scope of delivery
- Apollo base–board SK-AMAPOLLO-BASE-V11 in ESD bag - USB-Mico cable
Not scope of delivery: SK-AMAP1-BREAKOUT-V11 / SK-AMAP2-BREAKOUT-V11
59€ at shop.feeu.com
FEEU APOLLO EVALUATION PLATFORM Introduction
© Fujitsu Electronics Europe GmbH - 5 - FEEU APOLLO EVALUATION PLATFORM
1.2 The Apollo 1 breakout board SK-AMAP1-BREAKOUT-V11
The SK-AMAP1-BREAKOUT-V11 evaluation board includes an Ambiq Micro Apollo 1 MCU with all pins available at 54 pins.
1.2.1 Features
- Ambiq Micro Apollo 1: o Ultra-low active mode power consumption: 35µA/MHz (executing from Flash) o Ultra-low sleep mode power consumption: 143nA (with RTC on) o High-performance, 32-bit ARM Cortex-M4F processor
Up to 24MHz clock frequency Floating point unit Wake-up interrupt controller with 12 interrupts
o Ultra-low power memory Up to 512kB Flash Up to 64kB low-leakage RAM
o Ultra-low power interface for off-chip sensors 10-bit, 13-channel, 1MS/s ADC Temperature sensor with ±4°C accuracy
o Rich set of timing peripherals o Flexible serial peripherals
I2C/SPI master for communication with external peripherals I2C/SPI slave for optional host communications UART for communication with peripherals and legacy devices
o Wide operating range: 1.8 to 3.8V o Compact package options
64-pin BGA with 50 GPIO 41-pin CSP with 27 GPIO
- Parts assembled: o MCU o Passives o Crystal o DC/DC converter coils o Reset button o SWD Debug header o 2x 27 pin headers 2.54mm o 1x 10 pin communication header
1.2.2 Dimensions
- Width: 22mm - Height: 70mm
1.2.3 Scope of delivery
- Apollo 1 breakout board SK-AMAP1-BREAKOUT-V11 in ESD bag
19€ at shop.feeu.com
FEEU APOLLO EVALUATION PLATFORM Factsheet
FEEU APOLLO EVALUATION PLATFORM - 6 - © Fujitsu Electronics Europe GmbH
1.3 The Apollo 2 breakout board SK-AMAP2-BREAKOUT-V11
The SK-AMAP2-BREAKOUT-V11 evaluation board includes an Ambiq Micro Apollo 2 MCU with all pins available at 54 pins.
1.3.1 Features
- Ambiq Micro Apollo 2: o Ultra-low supply current:
<10 μA/MHz executing from flash at 3.3 V <10 μA/MHz executing from RAM at 3.3 V
o High-performance ARM Cortex-M4F Processor: Up to 48 MHz clock frequency Floating point unit Memory protection unit Wake-up interrupt controller with 32 interrupts
o Ultra-low power memory: Up to 1 MB of flash memory for code/data Up to 256 KB of low leakage RAM for code/data 16kB 2-way Associative Cache
o Ultra-low power interface for off-chip sensors: 14 bit, 15-channel, up to 1.2 MS/s ADC Temperature sensor with +/-3ºC accuracy Voltage Comparator
o Flexible serial peripherals: 6x I2C/SPI master for communication with sensors, radios, and other
peripherals 1x I2C/SPI slave for host communications 2x UART for communication with peripherals and legacy devices
o PDM for mono and stereo audio microphones o Rich set of clock sources:
32.768 kHz XTAL oscillator Low frequency RC oscillator – 1.024 kHz High frequency RC oscillator – 48 MHz
o RTC based on Ambiq’s AM08X5/18X5 families o Compact package options:
2.5 x 2.5 mm (0.35mm) 49-pin CSP with 34 GPIO 4.5 x 4.5 mm (0.5mm) 64-pin BGA with 50 GPIO
- Parts assembled: o MCU o Passives o Crystal o DC/DC converter coils o Reset button o SWD Debug header o 2x 27 pin headers 2.54mm o 1x 10 pin communication header
19€ at shop.feeu.com
FEEU APOLLO EVALUATION PLATFORM Introduction
© Fujitsu Electronics Europe GmbH - 7 - FEEU APOLLO EVALUATION PLATFORM
1.3.2 Dimensions
- Width: 22mm - Height: 70mm
1.3.3 Scope of delivery
- Apollo 2 breakout board SK-AMAP2-BREAKOUT-V11 in ESD bag