emergency brakes s / ds range
Post on 25-Nov-2021
1 Views
Preview:
TRANSCRIPT
S9 SH S/DS
20 SH
S/DS
30 SH
S/DS
50 SH
S/DS
60 SH
S/DS
130 SH
S/DS
190 SH
S/DS
300 SH
S/DS
400 SH
Braking force [kN] 9 20 30 50 60 130 190 300 400
Release pressure [bar] 60 100 120 160 180 200 200 200 200
Disc thickness [mm] ¹ 20 30 30 30 30 20 25 30 30
Weight S range[kg]
(With bracket )24 95 95 95 95 195 330 625 880
Weight S range [kg]
(Without bracket )19 67 67 67 67 125 210 405 565
Weight DS range [kg] - 80 80 80 80 140 237 425 650
(1) minimum thickness for the DS range
The S/DS range benefits of the ATV's long experience in industrial brakes, and reflects the state of the art in the field of emergency braking. These brakes are fail-safe, the clamping force is thus produced by spring washers, while the brake release occurs by means of an hydraulic pressure. These brakes provide emergency braking functions, generally on the low speed shaft of a drive. They so prevent every accident caused by a breakage in the drivetrain, by acting closest to the load, for instance on a brake disc which is flange-mounted on a hoist drum. This complete range may be fitted with an hydraulic power pack, factory piped and wired. These executions with integrated power pack (SHCI version) provide to the crane builder and the end-user as well a factory tested, reliable and autonomous product. The braking force can be factory adapted, over a setting range spreading out from 60 to 100% of the nominal value. Two types of brake assembly are available : The DS brakes are constituted of two half-calipers facing each other. The central bracket is fixed, the pad gap is maximized. These brakes can be adapted to any disc thickness. The S brakes are floating calipers constituted of one half-caliper and a slide movable on its bracket. For a given size, the S version provides the same force as a DS one. This caliper can so follow the disc axial run-out, either due to its own manufacturing tolerance or to its thermal and under load deformation. This solution makes it possible to optimize the sizing of emergency brakes for heavy-load cranes or for big diameter discs, while avoiding an early wear of the brake linings.
FAIL-SAFE DISC BRAKE
Spring applied - Hydraulic release
Instruction handbook nr 265
¹ Caliper orientation to be defined as per leaflet nr 224
Power pack definition: see leaflet nr 262
Technical features: Working conditions :
Braking force²: kN 9 Ambient temperature: -20° / +60°C
Total gap between pads and disc (nominal value): mm 1 Humidity: < 90 %
Response time: s 0,2
Release pressure: bar 60 Monitoring switches:
Maximal pressure: bar 80 240V 1,5A AC ; 250V 0,1A DC
Displaced volume for complete release: cm³ 12 Wire 5 x 0.75mm², length 2m., Øext 7.5mm
Disc thickness: mm 20 IP67 protection
Weight: kg 24
² Braking torque loss at 1mm pad wear: 8% Options :
- Integrated power pack
Braking torque : Cf [Nm] = 9 x Rf - Floating caliper alone delivered (no bracket)
Braking radius Rf [mm] = (ØD/2) -35 - Reduced closing time
Torque increase by up to 12% in dynamic mode (refer to ATV) - Pads fitted with wear wire or sintered (for high temp.)
- Seawater execution
Lifting ring not supplied - Low temperature execution
- Off-shore certifications
Fixation : 4 screws M16 class 8.8 (not supplied) - ATEX certifications for explosive atmospheres
Cs : 190 Nm ±10% µ 0,15
Calculation notes or 3D models available on request
2015-03 12721-FT2
www.atv.fr
Data
op
en
to
im
pro
ve
me
nt
S9 SH
Oil port 1/8'' BSP + bleeding screw on the opposite side ¹
Brake release and pad wear monitoring switches
FAIL-SAFE DISC BRAKE
Spring applied - Hydraulic release
Instruction handbook nr 265 3 mm max. 3 mm max.
¹ Caliper orientation to be defined as per leaflet nr 224 Disc position vs. brake support
Power pack definition: see leaflet nr 262
Technical features: S30 SH S20 SH Working conditions :
Braking force²: kN 30 20 Ambient temperature: -20° / +60°C
Total gap between pads and disc (nominal value): mm 1 1 Humidity: < 90 %
Response time: s 0,2 0,2
Release pressure: bar 120 100 Monitoring switches:
Maximal pressure: bar 150 130 240V 1,5A AC ; 250V 0,1A DC
Displaced volume for complete release: cm³ 15 15 Wire 5 x 0.75mm², length 2m., Øext 7.5mm
Disc thickness: mm 30 30 IP67 protection
Weight: kg 95 95
² Braking torque loss at 1mm pad wear: % 6 10 Options :
- Integrated power pack
Braking torque: Cf [Nm] = Braking force x Rf - Floating caliper alone delivered (no bracket)
Braking radius: Rf [mm] = (ØD/2) -67 - Reduced closing time
Torque increase by up to 12% in dynamic mode (refer to ATV) - Pads fitted with wear wire or sintered (for high temp.)
- Seawater execution
Lifting ring included - Low temperature execution
Right hand or Left hand mounted - Off-shore certifications
Fixation : 3 screws M20 class 8.8 (not supplied) - ATEX certifications for explosive atmospheres
Cs : 370 Nm ±10% µ 0,15
Calculation notes or 3D models available on request
2015-03 12516-FT2
www.atv.fr
Data
op
en
to
im
pro
ve
me
nt
S30 SH / S20 SH
Oil port 1/4'' BSP + bleeding screw on the opposite side¹
Hand release nut and readjustment screw
Pad take out zone
Left-hand mounting is shown
Brake release and pad wear monitoring switches
FAIL-SAFE DISC BRAKE
Spring applied - Hydraulic release
Instruction handbook nr 265 3 mm max. 3 mm max.
¹ Caliper orientation to be defined as per leaflet nr 224 Disc position vs. brake support
Power pack definition: see leaflet nr 262
Technical features: S60 SH S50 SH Working conditions :
Braking force²: kN 60 50 Ambient temperature: -20° / +60°C
Total gap between pads and disc (nominal value): mm 1 1 Humidity: < 90 %
Response time: s 0,2 0,2
Release pressure: bar 180 160 Monitoring switches:
Maximal pressure: bar 200 180 240V 1,5A AC ; 250V 0,1A DC
Displaced volume for complete release: cm³ 15 15 Wire 5 x 0.75mm², length 2m., Øext 7.5mm
Disc thickness: mm 30 30 IP67 protection
Weight: kg 95 95
² Braking torque loss at 1mm pad wear: % 7 8 Options :
- Integrated power pack
Braking torque: Cf [Nm] = Braking force x Rf - Floating caliper alone delivered (no bracket)
Braking radius: Rf [mm] = (ØD/2) -67 - Reduced closing time
Torque increase by up to 12% in dynamic mode (refer to ATV) - Pads fitted with wear wire or sintered (for high temp.)
- Seawater execution
Lifting ring included - Low temperature execution
Right hand or Left hand mounted - Off-shore certifications
Fixation : 3 screws M20 class 8.8 (not supplied) - ATEX certifications for explosive atmospheres
Cs : 370 Nm ±10% µ 0,15
Calculation notes or 3D models available on request
2015-03 12509-FT2
www.atv.fr
Data
op
en
to
im
pro
ve
me
nt
S60 SH / S50 SH
Oil port 1/4'' BSP + bleeding screw on the opposite side¹
Brake release and pad wear monitoring switches
Hand release nut and readjustment screw
Pad take out zone
Left-hand mounting is shown
FAIL-SAFE DISC BRAKE
Spring applied - Hydraulic release
Instruction handbook nr 253 7 mm max. 7 mm max.
¹ Caliper orientation to be defined as per leaflet nr 224 Disc position vs. brake support
Power pack definition: see leaflet nr 262
Technical features: Working conditions :
Braking force²: kN 130 Ambient temperature: -20° / +60°C
Total gap between pads and disc (nominal value): mm 1 Humidity: < 90 %
Response time: s 0,2
Release pressure: bar 200 Monitoring switches:
Maximal pressure: bar 230 240V 1,5A AC ; 250V 0,1A DC
Displaced volume for complete release: cm³ 30 Wire 5 x 0.75mm², length 2m., Øext 7.5mm
Disc thickness: mm 20 IP67 protection
Weight: kg 195
² Braking torque loss at 1mm pad wear: 12% Options :
- Integrated power pack
Braking torque: Cf [Nm] = 130 x Rf - Floating caliper alone delivered (no bracket)
Braking radius: Rf [mm] = (ØD/2) -70 - Reduced closing time
Torque increases by up to 12% in dynamic mode (refer to ATV) - Pads fitted with wear wire or sintered (for high temp.)
- Seawater execution
Lifting ring included - Low temperature execution
Right hand or Left hand mounted - Off-shore certifications
Fixation : 6 screws M20 class 8.8 (not supplied) - ATEX certifications for explosive atmospheres
Cs : 370 Nm ±10% µ 0,15
Calculation notes or 3D models available on request
2015-03 12708-FT2
www.atv.fr
Data
op
en
to
im
pro
ve
me
nt
S130 SH
Brake release and pad wear monitoring switches
Hand release and readjustment screw behind cover
Oil port 1/8'' BSP + bleeding screw on the opposite side¹
Pad take out zone
Left-hand mounting is shown
FAIL-SAFE DISC BRAKE
Spring applied - Hydraulic release
Instruction handbook nr 253 8 mm max. 8 mm max.
¹ Caliper orientation to be defined as per leaflet nr 224 Disc position vs. brake support
Power pack definition: see leaflet nr 262
Technical features: Working conditions :
Braking force²: kN 190 Ambient temperature: -20° / +60°C
Total gap between pads and disc (nominal value): mm 1 Humidity: < 90 %
Response time: s 0,2
Release pressure: bar 200 Monitoring switches:
Maximal pressure: bar 230 240V 1,5A AC ; 250V 0,1A DC
Displaced volume for complete release: cm³ 40 Wire 5 x 0.75mm², length 2m., Øext 7.5mm
Disc thickness: mm 25 IP67 protection
Weight: kg 330
² Braking torque loss at 1mm pad wear: 7% Options :
- Integrated power pack
Braking torque: Cf [Nm] = 190 x Rf - Floating caliper alone delivered (no bracket)
Braking radius: Rf [mm] = (ØD/2) -90 - Reduced closing time
Torque increases by up to 12% in dynamic mode (refer to ATV) - Pads fitted with wear wire or sintered (for high temp.)
- Seawater execution
Lifting ring included - Low temperature execution
Right hand or Left hand mounted - Off-shore certifications
Fixation : 6 screws M24 class 8.8 (not supplied) - ATEX certifications for explosive atmospheres
Cs : 630 Nm ±10% µ 0,15
Calculation notes or 3D models available on request
2015-03 12712-FT2
www.atv.fr
Data
op
en
to
im
pro
ve
me
nt
S190 SH
Brake release and pad wear monitoring switches
Pad take out zone
Hand release and readjustment screw behind cover
Oil port 1/4'' BSP + bleeding screw on the opposite side¹
Left-hand mounting is shown
FAIL-SAFE DISC BRAKESpring applied - Hydraulic release
www.atv.fr
Dat
a op
en to
impr
ovem
ent
S300 SH
Brake release and pad
wear monitoring
switches
Left-hand mounting is shown
Oil port3/8'' BSP +bleeding screw on the opposite side¹
Hand release andreadjustment screwbehind cover
Pad take out zone
Instruction handbook nr 227 9 mm max. 9 mm max.¹ Caliper orientation to be defined as per leaflet nr 224 Disc position vs. brake support Power pack definition: see leaflet nr 262
Technical features: Working conditions :Braking force²: kN 300 Ambient temperature: -20° / +60°CTotal gap between pads and disc (nominal value): mm 1 Humidity: < 90 %Response time: s 0,2Release pressure: bar 200 Monitoring switches:Maximal pressure: bar 230 240V 1,5A AC ; 250V 0,1A DCDisplaced volume for complete release: cm³ 70 Wire 5 x 0.75mm², length 2m., Øext 7.5mm Disc thickness: mm 30 IP67 protectionWeight: kg 625
² Braking torque loss at 1mm pad wear: 9% Options :- Integrated power pack
Braking torque: Cf [Nm] = 300 x Rf - Floating caliper alone delivered (no bracket)Braking radius: Rf [mm] = (ØD/2) -107 - Reduced closing timeTorque increases by up to 12% in dynamic mode (refer to ATV) - Pads fitted with wear wire or sintered (for high temp.)
- Seawater executionLifting ring included - Low temperature executionRight hand or Left hand mounted - Off-shore certificationsFixation : 6 screws M30 class 8.8 (not supplied) - ATEX certifications for explosive atmospheresCs : 1200 Nm ±10% µ 0,15
Calculation notes or 3D models available on request
2014-04 12660-FT22014-04 12660-FT2
FAIL-SAFE DISC BRAKESpring applied - Hydraulic release
www.atv.fr
S400 SH
Dat
a op
en to
impr
ovem
ent
Brake release and pad wear monitoring switches
Hand release andreadjustment screwbehind cover
Oil port3/8'' BSP +bleeding screw on the opposite side¹
Left-hand mounting is shown
Pad take out zone
Instruction handbook nr 246¹ Caliper orientation to be defined as per leaflet nr 224 12 mm max. 12 mm max.Power pack definition: see leaflet nr 262 Disc position vs. brake support
Technical features: Working conditions :Braking force²: kN 400 Ambient temperature: -20° / +60°CTotal gap between pads and disc (nominal value): mm 2 Humidity: < 90 %Response time: s 0,3Release pressure: bar 200 Monitoring switches:Maximal pressure: bar 230 240V 1,5A AC ; 250V 0,1A DCDisplaced volume for complete release: cm³ 150 Wire 5 x 0.75mm², length 2m., Øext 7.5mm Disc thickness: mm 30 IP67 protectionWeight: kg 880
² Braking torque loss at 1mm pad wear: 7% Options :- Integrated power pack
Braking torque: Cf [Nm] = 400 x Rf - Floating caliper alone delivered (no bracket)Braking radius: Rf [mm] = (ØD/2) -130 - Reduced closing timeTorque increases by up to 12% in dynamic mode (refer to ATV) - Pads fitted with wear wire or sintered (for high temp.)
- Seawater executionLifting ring included - Low temperature executionRight hand or Left hand mounted - Off-shore certificationsFixation : 8 screws M36 class 8.8 (not supplied) - ATEX certifications for explosive atmospheresCs : 2200 Nm ±10% µ 0,15
Calculation notes or 3D models available on request
2014-04 12662-FT22014-04 12662-FT2
FAIL-SAFE DISC BRAKESpring applied - Hydraulic release
www.atv.fr
DS30 / DS20 SH
Bracket
Brake release and pad wear monitoring switches (per half-caliper)
Dat
a op
en to
impr
ovem
entOil port 1/4'' BSP +
bleeding screw on the opposite side¹ (per half-caliper)
Optional set of bolts
Pad take out zone
Instruction handbook nr 165¹ Caliper orientation to be defined as per leaflet nr 224
Support Disc Power pack definition: see leaflet nr 262
Technical features: DS30 SH DS20 SH Working conditions :Braking force²: kN 30 20 Ambient temperature: -20° / +60°CTotal gap between pads and disc (nominal value): mm 2 2 Humidity: < 90 %Response time: s 0,2 0,2Release pressure: bar 120 100 Monitoring switches:Maximal pressure: bar 150 130 240V 1,5A AC ; 250V 0,1A DCDisplaced volume for complete release: cm³ 25 25 Wire 5 x 0.75mm², length 2m., Øext 7.5mm Min. disc thickness E: mm 15 15 IP67 protectionWeight: kg 80 80
² Braking torque loss at 1mm pad wear % 4 6 Options :- Mounting kit (screws, nuts, washers)
Braking torque: Cf [Nm] = Braking force x Rf - Brake supportBraking radius: Rf [mm] = (ØD/2) -65 - Reduced closing timeTorque increase by up to 12% in dynamic mode (refer to ATV) - Pads fitted with wear wire or sintered (for high temp.)
- Seawater execution2 off lifting rings included - Low temperature execution
- Off-shore certificationsFixation : 4 screws M20 class 8.8 (not supplied) - ATEX certifications for explosive atmospheresCs : 286 Nm ±10% µ 0,10
Calculation notes or 3D models available on request
2014-04 12516-FT1
Support drill drawing
Hand release nut and readjustment screw
2014-04 12516-FT1
FAIL-SAFE DISC BRAKESpring applied - Hydraulic release
www.atv.fr
DS60 / DS50 SH
Optional set of bolts
Bracket
Dat
a op
en to
impr
ovem
ent
Oil port 1/4'' BSP +bleeding screw on the opposite side¹ (per half-caliper)
Pad take out zone
Brake release and pad wear monitoring switches (per half-caliper)
Instruction handbook nr 165¹ Caliper orientation to be defined as per leaflet nr 224
Support Disc Power pack definition: see leaflet nr 262
Technical features: DS60 SH DS50 SH Working conditions :Braking force²: kN 60 50 Ambient temperature: -20° / +60°CTotal gap between pads and disc (nominal value): mm 2 2 Humidity: < 90 %Response time: s 0,2 0,2Release pressure: bar 180 160 Monitoring switches:Maximal pressure: bar 200 180 240V 1,5A AC ; 250V 0,1A DCDisplaced volume for complete release: cm³ 25 25 Wire 5 x 0.75mm², length 2m., Øext 7.5mm Min. disc thickness E: mm 15 15 IP67 protectionWeight: kg 80 80
² Braking torque loss at 1mm pad wear % 4 5 Options :- Mounting kit (screws, nuts, washers)
Braking torque: Cf [Nm] = Braking force x Rf - Brake supportBraking radius: Rf [mm] = (ØD/2) -65 - Reduced closing timeTorque increase by up to 12% in dynamic mode (refer to ATV) - Pads fitted with wear wire or sintered (for high temp.)
- Seawater execution2 off lifting rings included - Low temperature execution
- Off-shore certificationsFixation : 4 screws M20 class 10.9 (not supplied) - ATEX certifications for explosive atmospheresDS50 : Cs : 420 Nm ±10% µ 0,10 DS60 : Cs : 440 Nm ±5% µ 0,10 Calculation notes or 3D models available on request
2014-04 12509-FT1
Support drill drawing
Hand release nut and readjustment screw
2014-04 12509-FT1
FAIL-SAFE DISC BRAKE
Spring applied - Hydraulic release
Instruction handbook nr 252
¹ Caliper orientation to be defined as per leaflet nr 224
Support Disc Power pack definition: see leaflet nr 262
Technical features: Working conditions :
Braking force²: kN 130 Ambient temperature: -20° / +60°C
Total gap between pads and disc (nominal value): mm 2 Humidity: < 90 %
Response time: s 0,2
Release pressure: bar 200 Monitoring switches:
Maximal pressure: bar 230 240V 1,5A AC ; 250V 0,1A DC
Displaced volume for complete release: cm³ 60 Wire 5 x 0.75mm², length 2m., Øext 7.5mm
Min. disc thickness E: mm 20 IP67 protection
Weight: kg 140
² Braking torque loss at 1mm pad wear: 7% Options :
- Mounting kit (screws, nuts, washers)
Braking torque: Cf [Nm] = 130 x Rf - Brake support
Braking radius: Rf [mm] = (ØD/2) -70 - Reduced closing time
Torque increase by up to 12% in dynamic mode (refer to ATV) - Pads fitted with wear wire or sintered (for high temp.)
- Seawater execution
Including 2 pairs of shear pins Ø30g6 - Low temperature execution
2 off lifting rings included - Off-shore certifications
Fixation : 6 screws M24 class 10.9 (not supplied) - ATEX certifications for explosive atmospheres
Cs : 930 Nm ±10% µ 0,15
Calculation notes or 3D models available on request
2015-03 12708-FT1
www.atv.fr
DS130 SH
Support drill drawing
Bracket
Data
op
en
to
im
pro
ve
me
nt
Hand release nut and readjustment screw
Optional set of bolts
Oil port 1/8'' BSP + bleeding screw on the opposite side¹ (per half-caliper)
Brake release and pad wear monitoring switches (per half-caliper)
Pad take out zone
FAIL-SAFE DISC BRAKE
Spring applied - Hydraulic release
Instruction handbook nr 252
¹ Caliper orientation to be defined as per leaflet nr 224
Support Disc Power pack definition: see leaflet nr 262
Technical features: Working conditions :
Braking force²: kN 190 Ambient temperature: -20° / +60°C
Total gap between pads and disc (nominal value): mm 2 Humidity: < 90 %
Response time: s 0,2
Release pressure: bar 200 Monitoring switches:
Maximal pressure: bar 230 240V 1,5A AC ; 250V 0,1A DC
Displaced volume for complete release: cm³ 70 Wire 5 x 0.75mm², length 2m., Øext 7.5mm
Min. disc thickness E: mm 25 IP67 protection
Weight: kg 237
² Braking torque loss at 1mm pad wear: 4% Options :
- Mounting kit (screws, nuts, washers)
Braking torque: Cf [Nm] = 190 x Rf - Brake support
Braking radius: Rf [mm] = (ØD/2) -90 - Reduced closing time
Torque increase by up to 12% in dynamic mode (refer to ATV) - Pads fitted with wear wire or sintered (for high temp.)
- Seawater execution
Including 2 pairs of shear pins Ø32g6 - Low temperature execution
2 off lifting rings included - Off-shore certifications
Fixation : 6 screws M27 class 10.9 (not supplied) - ATEX certifications for explosive atmospheres
Cs : 1380 Nm ±10% µ 0,15
Calculation notes or 3D models available on request
2015-03 12712-FT1
www.atv.fr
DS190 SH
Support drill drawing
Bracket
Data
op
en
to
im
pro
ve
me
nt
Hand release and readjust-ment screw behind cover
Pad take out zone Brake release and pad
wear monitoring switches (per half-caliper)
Oil port 1/4'' BSP + bleeding screw on the opposite side¹ (per half-caliper)
Optional set of bolts
FREIN A DISQUE DE SECURITE
Spring applied - Hydraulic release
Instruction handbook nr 223
¹ Caliper orientation to be defined as per leaflet nr 224
Support Disc Power pack definition: see leaflet nr 262
Technical features: Working conditions :
Braking force²: kN 300 Ambient temperature: -20° / +60°C
Total gap between pads and disc (nominal value): mm 2 Humidity: < 90 %
Response time: s 0,3
Release pressure: bar 200 Monitoring switches:
Maximal pressure: bar 230 240V 1,5A AC ; 250V 0,1A DC
Displaced volume for complete release: cm³ 120 Wire 5 x 0.75mm², length 2m., Øext 7.5mm
Min. disc thickness E: mm 30 IP67 protection
Weight: kg 425
² Braking torque loss at 1mm pad wear: 5% Options :
- Mounting kit (screws, nuts, washers)
Braking torque: Cf [Nm] = 300 x Rf - Brake support
Braking radius: Rf [mm] = (ØD/2) -107 - Reduced closing time
Torque increase by up to 12% in dynamic mode (refer to ATV) - Pads fitted with wear wire or sintered (for high temp.)
- Seawater execution
Including 2 pairs of shear pins Ø46g6 - Low temperature execution
2 off lifting rings included - Off-shore certifications
Fixation : 6 screws M33 class 10.9 (not supplied) - ATEX certifications for explosive atmospheres
Cs : 1950 Nm ±5% µ 0,10
Calculation notes or 3D models available on request
2015-03 12660-FT1
www.atv.fr
DS300 SH
Bracket
Data
op
en
to
im
pro
ve
me
nt
Oil port 3/8'' BSP + bleeding screw on the opposite side¹ (per half-caliper)
Brake release and pad wear monitoring switches (per half-caliper)
Pad take out zone
Optional set of bolts
Hand release and readjust-ment screw behind cover
Support drill drawing
FAIL-SAFE DISC BRAKE
Spring applied - Hydraulic release
Instruction handbook nr 246
¹ Caliper orientation to be defined as per leaflet nr 224
Support Disc Power pack definition: see leaflet nr 262
Technical features: Working conditions :
Braking force²: kN 400 Ambient temperature: -20° / +60°C
Total gap between pads and disc (nominal value): mm 4 Humidity: < 90 %
Response time: s 0,4
Release pressure: bar 200 Monitoring switches:
Maximal pressure: bar 230 240V 1,5A AC ; 250V 0,1A DC
Displaced volume for complete release: cm³ 270 Wire 5 x 0.75mm², length 2m., Øext 7.5mm
Min. disc thickness E: mm 30 IP67 protection
Weight: kg 650
² Braking torque loss at 1mm pad wear: 4% Options :
- Mounting kit (screws, nuts, washers)
Braking torque: Cf [Nm] = 400 x Rf - Brake support
Braking radius: Rf [mm] = (ØD/2) -130 - Reduced closing time
Torque increases by up to 12% in dynamic mode (refer to ATV) - Pads fitted with wear wire or sintered (for high temp.)
- Seawater execution
Including 2 pairs of shear pins Ø55g6 - Low temperature execution
2 off lifting rings included - Off-shore certifications
Fixation : 6 screws M42 class 10.9 (not supplied) - ATEX certifications for explosive atmospheres
Cs : 4100 Nm ±5% µ 0,10
Calculation notes or 3D models available on request
2014-04 12662-FT1
www.atv.fr
DS400 SH
Bracket
Data
op
en
to
im
pro
ve
me
nt
Optional set of bolts
Oil port 3/8'' BSP + bleeding screw on the opposite side¹ (per half-caliper)
Brake release and pad wear monitoring switches (per half-caliper)
Support drill drawing
Hand release and readjust-ment screw behind cover
Pad take out zone
CRANES - HOISTING DEVICESFRANCE EIFFAGE CONSTRUCTION METALLIQUE - REEL - ADC - NFM - KONECRANES - SOMDEL -
SEVAL - COMETE - JOSEPH PARIS - CEGELEC - CMI - MC LEVAGE - MANITOWOC CRANE CARE
GERMANY KRANBAU KÖTHEN - STALVOSS - NOELL - KRAFOTEC - BRUNNHUBER - DEMAG CRANES - UTRANS
ITALY ANSALDO - DEMAG - ITALIMPIANTI - TECHINT - BONFANTI SIDER PIOMBINO - ALMICI - MELONI - TENOVA - ITALGRU
AUSTRIA ING. VOITH TRAUNASIA DHHI GROUP
WIND & WATER TURBINESFRANCE ALSTOM OCEAN ENERGY - SABELLANEDERLAND TOCARDOGERMANY ENERCON
PORT CRANESFRANCE PHB - SOMDEL - POTAIN HARBOURS : NANTES - ST NAZAIRE - LORIENT - BREST - MARSEILLE - SETE - LE HAVRE
- LA ROCHELLE - DIEPPE - CHERBOURG - LILLE - STRASBOURG - TOULON - BORDEAUX - CAEN - FOS SUR MER
GERMANY HAMBURG - BREMEN - MAINZMAROCCO CASABLANCAALGERIA ALGER - SKIKDA - ANNABATURKEY ISTAMBUL
SPECIAL MACHINESFRANCE POURTIER –FIVES STEIN - SIDEL - FIVES CAIL BABCOCK - CEGELEC - SIEMENS VAI - SETIC
MILTEC - BAUDIN CHATEAUNEUF - SAPELEM - BROCHOT - MARCEAU AMALRIC - CNRS - GED - ADREM - AREVA VINCI
GERMANY AUGUST MÖSSNERGREECE GEFYRA - TENOVAITALY TENOVA
RAIL / ROAD INDUSTRYFRANCE RATP - SNCF - POMA OTIS - AREVA - EUROVIA - COLAS RAIL - RAZEL BEC
STEELWORKSFRANCE ARCELOR MITTAL - CONSTELLIUM - AUBERT ET DUVAL –ASCOMETAL - UGITECH
- SALZGITTER MANNESMANN PRECISION - NEXANS - CREUSOT FORGES - INDUSTEEL - FERROPEM
ITALY DALMINE - ILVA - AST - ARCELORMITTAL PIOMBINO - DANIELI - RIVA - ITALSIDER
GERMANY ARCELORMITTAL BREMEN - SAARSTAHL - ARCELORMITTAL HAMBURG - SALZGITTER FLACHSTAHL BES RIVA STAHL
SWEDEN AVESTA - SSAB - SANDVIKENNEDERLAND TATASTEEL IJMUIDENBELGIUM ARCELORMITTAL - INDUSTEEL - UGINE ALZLUXEMBURG ARCELORMITTAL ALGERIA ARCELORMITTAL ALGERIESPAIN ARCELORMITTAL SAGUNTOIRAN MOBARAKEH STEEL
MISCELLANEOUSFRANCE RENAULT - PSA - MICHELIN - FCB - AREVA - ARCELOR –- PLACOPLATRE - DMS - CALCIA -
COFELY ENDEL - CREUZET AERONAUTIQUE - SOMAB - GOODYEAR DUNLOP
CONVEYORSFRANCE KOCH - SOMDEL - RBL REI - CLAUDIUS PETERGERMANY FAM - VOITH TURBOAUSTRALIA YALLOURN - COMALCO - BARCLAY MOWLEM - BHP
ENERGYFRANCE EDF - GDF - CNR - COFELY - INCINERATION FACTORY - CNIM - IPXIII - ANDRA - NOVERGIECHINA DAYA BAY - SHANXIA WATER CONSERVANCY - HAI YANG NPP
MARINE - OFF SHOREFRANCE NFM - COMEX - FLEXI-FRANCE - KLEY FRANCE - REEL IMECAITALY SAIPEM - REMACUT - REMA ENGINEERING - FINCANTIERINEDERLAND ERS - HUISMANGERMANY BLOHM & VOSS - LÜRSSEN WERFT
PAPER INDUSTRYFRANCE ALLIMAND - PROCOAT - SMURFIT SOCAR - PAPETERIE PONT DE CLAIX - AUSSEDAT REY
ROPEWAYSFRANCE POMAGALSKI - GIMAR MONTAZ MAUTINO - SEIREL - LST ROPEWAYITALY LEITNER - GRAFFER - GARAVENTA
DEFENCE INDUSTRYFRANCE DGA - DCNS - NEXTER SYSTEMS - THOMSON CSF - MARINE NATIONALE - ARMEE DE L’AIR -
ESID
Nr. 0016921-00 – ISO 9001-2008
Abstract of references
Sales & Design OfficeParc du Saint Laurent. Bat Montréal54, route de Sartrouville - 78230 LE PECQ (FRANCE)Tél : +33 (0)1 30 15 41 00 - Fax : +33 (0)1 30 15 41 19www.atv.fr - e-mail : info@atv.fr
Workshops - Quality Control Route de la Libération08300 RETHEL (FRANCE)Tél : +33 (0)3 24 38 26 26Fax : +33 (0)3 24 38 25 3303-2015
top related