421 series heavy duty clevis hanger1 slide pipe through clevis hanger or disassemble clevis hanger...

Load

Part Number Article Number

Nominal Pipe Size

Rod SizeMaximum

Recommended Load

Inch mm Lbs N4210250EG 179721 2-1/2" 1/2" 12

780 34704210300EG 179722 3" 1/2" 124210350EG 179723 3-1/2" 1/2" 124210400EG 179724 4" 5/8" 16 1050 46714210500EG 179725 5" 5/8" 164210600EG 179726 6" 3/4" 20 1940 86304210800EG 179727 8" 3/4" 20 2000 88964211000EG 179728 10" 7/8" 22 3600 160144211200EG 179729 12" 7/8" 22 3800 16903

TECHNICAL SUPPORT:www.erico.pentair.com CFS551_B

INSTRUCTION SHEET

1 OF 3 © 2016-2017 Pentair All Rights Reserved

421 Series Heavy Duty Clevis Hanger

WARNING:Pentair products shall be installed and used only as indicated in Pentair product instruction sheets and training materials. Instruction sheets are available at 1.www.erico.pentair.com and from your Pentair customer service representative. PENTAIR products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.2.All instructions must be completely followed to ensure proper and safe installation and performance. 3.Improper installation, misuse, misapplication or other failure to completely follow Pantair's instructions and warnings may cause product malfunction, property 4.damage, serious bodily injury and/or death, and void your warranty.Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment. 5.All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any 6.other purpose.

NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.

The customer is responsible for:a. Conformance to all governing codes.b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified engineer.c. Using appropriate industry standard hardware as noted above.

SAFETY INSTRUCTIONS: All governing codes and regulations and those required by the job site must be observed. Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.

Pentair, CADDY, ERICO CADWELD, ERICO CRITEC, ERICO, ERIFLEX, and LENTON are owned by Pentair or its global affiliates. All other trademarksare the property of their respective owners. Pentair reserves the right to change specifications without prior notice.

1

2

3

45

Installation notes:

1 Slide pipe through Clevis Hanger or disassemble Clevis Hanger and place over pipe.

2 Install top hex nut on threaded rod (Threaded rod and hex nuts not provided).

3 Insert threaded rod into Clevis Hanger and secure with bottom hex nut.

4 Tighten cross bar bolt per table (minimum 1/4 turn).

5 For fire sprinkler applications, install and tighten hex nut (not provided)on bolt .

Part Number Torque Cross Bar Boltin-lbs Nm4210250

25 2.83 3/8-16 UNC-2A4210300421035042104004210500 30 3.39 1/2-13 UNC-2A42106004210800 50 5.65 5/8-11 UNC-2A4211000 75 8.47 3/4-10 UNC-2A4211200

TECHNICAL SUPPORT:www.erico.pentair.com CFS551_B

INSTRUCTION SHEET

2 OF 3 © 2016-2017 Pentair All Rights Reserved

Pentair, CADDY, ERICO CADWELD, ERICO CRITEC, ERICO, ERIFLEX, and LENTON are owned by Pentair or its global affiliates. All other trademarksare the property of their respective owners. Pentair reserves the right to change specifications without prior notice.

1 Insert shield into clevis hanger.2 Insert the three (3) tabs on the shield

into the slot on the clevis hanger.

3 Bend middle tab of shieldcompletely over lip of slot on clevis hanger to secure shield in place.

121 Shield Installation (Shield not included with 421 Clevis hanger)

TECHNICAL SUPPORT:www.erico.pentair.com CFS551_B

INSTRUCTION SHEET

3 OF 3 © 2016-2017 Pentair All Rights Reserved

Pentair, CADDY, ERICO CADWELD, ERICO CRITEC, ERICO, ERIFLEX, and LENTON are owned by Pentair or its global affiliates. All other trademarksare the property of their respective owners. Pentair reserves the right to change specifications without prior notice.