chemical anchoring chemset reo502
Post on 13-Apr-2018
217 Views
Preview:
TRANSCRIPT
7/26/2019 Chemical Anchoring ChemSet Reo502
http://slidepdf.com/reader/full/chemical-anchoring-chemset-reo502 1/286 www.ramset.com.au 1300 780 063
ChemSet™ Reo502™
Extra Heavy Duty Anchoring
Features & Benefits• Quick cure for improved productivity.
• Sag resistant formula for horizontal holes
• Bonds to carbide and diamond core drilled holes – strong bond
• For Grade 500 reinforcing bar
• Excellent electrical insulation properties
Typical PropertiesProperties Typical Value
Appearance Part A: White Part B: Black
Mixed: Light Grey
Density 1.28 kg /litre @ 20°C
Heat Distortion Temperature Approx. 80°C
Hardness > Shore D 80
Compressive Strength (ASTM C579-01) 105 MPa
Dielectric Constant 3.95
Conductivity 8 x 10-11 ohmS/m
Service Temperature Limits -10°C to 80°C
Chemical Resistance See Technical Data Sheet
Substrates Solid Concrete, Solid Stone (Proof
loading recommended ), Solid Brick
I n j e c t i o
n
A d h e s i v e s
DescriptionExtra heavy duty anchoring of reinforcing bar and threaded studs into solid
concrete and stone.Two-component, high bond strength epoxy adhesive
specially designed for structural connections, such as reinforcing bar.
Suitable for dry, damp, wet and flooded holes. Quick setting for improved
productivity. Long working time to reduce nozzle wastage. Bar development
lengths in accordance with AS3600. Structural reinforcing bar connections in
slabs, columns, beams and walls. Structural steel columns, raker angles,
seating.
Trades & Applications
Key Features• Extra heavy duty epoxy
• Quick 3 hour cure time
• Dry, damp, wet and ooded holes
• Suitable underwater
• Long 20 minute working time for
deep embedment
Concreter Building
Contractor
Civil
Contractor
Steel
Fabricator
Balustrade
Contractor
Formworker Bricklayer Fitter
Post-installing reinforcing bar 4 4 4 4
Starter bars 4 4 4 4 4
Threaded studs 4 4 4 4 4
Tap valve to preserve contents
Robust, puncture
proof packaging
Translucent cartridge to
see remaining contents
Extension for deep holes
Made in Australia
ISNE REO502J (750ml)
Related ProductsDynaDrill™
Carbide Drill Bits
Diamond Motor
Diamond Core Drill Bits
V O C C o m p l i
a n t
Impact Wrench
Wet/Dry Vacuum
Hole Cleaning Brushes
Hole Cleaning Pump
7/26/2019 Chemical Anchoring ChemSet Reo502
http://slidepdf.com/reader/full/chemical-anchoring-chemset-reo502 2/2 www.ramset.com.au 1300 780 063 87
ChemSet™ Reo502™
Extra Heavy Duty Anchoring
Installation in Solid Concrete1. Drill or core hole to specified diameter and depth
2. Remove dust and debris by brushing and blowing 3 times each (If hole is wet
or flooded, brush only remove water and slurry with wet/dry vacuum)
3. Screw mixing nozzle onto cartridge and dispense 2-3 trigger pulls of adhesive
to waste until colour is light grey with no streaks
4. Insert tip of nozzle to bottom of hole and dispense adhesive
5. Fill hole to about 2/3 full
6. Insert threaded stud or reinforcing bar with rotating motion to release
trapped air
7. Wait until adhesive has fully cured before loading (see Working / Loading
Time chart below)
8. Clean up with acetone
Refer to Technical Data Sheet and MSDS available from
www.ramset.com.au, for precautions and further detailed
installation instructions
Working and Loading TimeSubstrate Temperature
(°C)
Gel Time
(min)
Cure Time
(hours)
10 21 8
16 18 5
20 20 3
27 12 2.5
32 8.5 2
I n j e c t i o n
A d h
e s i v e s
Recommended Installation TemperaturesMinimum Maximum
Substrate 5°C 40°C
Adhesive 20°C 32°C
ChemSet™ Reo 502™ - Indicative Working Loads in 32 MPa Concrete with ChemSet™
Anchor StudsThreadSize
Drilled HoleØ (mm)
Min HoleDepth (mm)
TighteningTorque (Nm)
Min EdgeDistance (mm)
Min AnchorSpacing (mm)
Max TensileLoad, Na (kN)
Max ShearLoad, V as
(kN)*
M8 10 80 10 35 50 6.3 4.4
M10 12 90 20 40 60 10.3 7.1
M12 14 110 40 50 75 15.3 10.5
M16 18 125 95 65 100 29.4 19.9
M20 24 150 180 80 120 37.9 29.9
M20 24 170 180 80 120 43.0 29.9
M24 26 160 315 100 145 40.9 43.3
M24 26 210 315 100 145 53.6 43.3
M30 32 270 600 120 180 72.4 90.4+
M36 38 330 1050 145 220 101.5 131.7+
Bold working load values in tension are limited by steel. All other values limited by concrete and adhesive bond
* For shear acting towards a concrete edge please contact a Ramset Engineer for further design assistance+ M30 and M36 steel shear values are for Grade 8.8 carbon steel. All other values are for Grade 5.8 carbon steel.
For water saturated or under water holes, reduce tensile load capacity by 30%
Hole ConditionHole Condition Suitable
Dry Yes
Damp Yes
Wet Yes
Flooded Yes
Drill Bit Type
Carbide Yes
Diamond Core Yes
Hole Orientation
Vertical Down Yes
Horizontal Yes
Vertical Up (Overhead) Contact Ramset™
ChemSet™ Reo 502™ Anchoring AdhesiveDescription Part No Box Quantity
Jumbo Cartridge (750 ml) + 1 Nozzle REO502J 12
ChemSet™ Universal Applicator CUA 1
ChemSet™ Pneumatic Universal Applicator CUAPN 1
Mixing Nozzles for Epoxy with Extension ISNE 5
Mixing Nozzle Turbo (Easier Dispensing) ISNET 1
Hole Cleaning Pump HCP 1
Hole Cleaning Pump High Volume HCPHV 1
Hole Cleaning Brush 13 mm HCBT13 1
Hole Cleaning Brush 20 mm HCBT20 1
Hole Cleaning Brush 26 mm HCBT26 1
Description Part No Box Quantity
The design engineer should ensure the structural element is capable of supporting these loads.
Refer to Ramset™ Specifiers Resource Book for more information or explanation of technical data.
Working load capacity was derived from characteristicultimate load capacity by applying the following factors:
Tension: Concrete = 3, Steel = 2.2
Shear: Steel = 2.5
top related