7/26/2019 Chemical Anchoring ChemSet Reo502

http://slidepdf.com/reader/full/chemical-anchoring-chemset-reo502 1/286 www.ramset.com.au 1300 780 063

ChemSet™ Reo502™

Extra Heavy Duty Anchoring

Features & Benefits• Quick cure for improved productivity.

• Sag resistant formula for horizontal holes

• Bonds to carbide and diamond core drilled holes – strong bond

• For Grade 500 reinforcing bar

• Excellent electrical insulation properties

Typical PropertiesProperties Typical Value

 Appearance Part A: White Part B: Black

Mixed: Light Grey

Density 1.28 kg /litre @ 20°C

Heat Distortion Temperature  Approx. 80°C

Hardness > Shore D 80

Compressive Strength (ASTM C579-01) 105 MPa

Dielectric Constant 3.95

Conductivity 8 x 10-11 ohmS/m

Service Temperature Limits -10°C to 80°C

Chemical Resistance See Technical Data Sheet

Substrates Solid Concrete, Solid Stone (Proof

loading recommended ), Solid Brick 

 I n j e c t i o

 n

 A d h e s i v e s

DescriptionExtra heavy duty anchoring of reinforcing bar and threaded studs into solid

concrete and stone.Two-component, high bond strength epoxy adhesive

specially designed for structural connections, such as reinforcing bar.

Suitable for dry, damp, wet and flooded holes. Quick setting for improved

productivity. Long working time to reduce nozzle wastage. Bar development

lengths in accordance with AS3600. Structural reinforcing bar connections in

slabs, columns, beams and walls. Structural steel columns, raker angles,

seating.

Trades & Applications

Key Features• Extra heavy duty epoxy

• Quick 3 hour cure time

• Dry, damp, wet and ooded holes

• Suitable underwater

• Long 20 minute working time for

deep embedment

Concreter Building

Contractor

Civil

Contractor

Steel

Fabricator

Balustrade

Contractor

Formworker Bricklayer Fitter

Post-installing reinforcing bar   4 4 4 4

Starter bars 4 4 4 4 4

Threaded studs   4 4 4 4 4

Tap valve to preserve contents

Robust, puncture

proof packaging

Translucent cartridge to

see remaining contents

Extension for deep holes

Made in Australia

ISNE REO502J (750ml)

Related ProductsDynaDrill™ 

Carbide Drill Bits

Diamond Motor

Diamond Core Drill Bits

 V O C C o m p l i

 a n t

Impact Wrench

Wet/Dry Vacuum

Hole Cleaning Brushes

Hole Cleaning Pump

7/26/2019 Chemical Anchoring ChemSet Reo502

http://slidepdf.com/reader/full/chemical-anchoring-chemset-reo502 2/2  www.ramset.com.au 1300 780 063 87

ChemSet™ Reo502™

Extra Heavy Duty Anchoring

Installation in Solid Concrete1. Drill or core hole to specified diameter and depth

2. Remove dust and debris by brushing and blowing 3 times each (If hole is wet

or flooded, brush only remove water and slurry with wet/dry vacuum)

3. Screw mixing nozzle onto cartridge and dispense 2-3 trigger pulls of adhesive

to waste until colour is light grey with no streaks

4. Insert tip of nozzle to bottom of hole and dispense adhesive

5. Fill hole to about 2/3 full

6. Insert threaded stud or reinforcing bar with rotating motion to release

trapped air

7. Wait until adhesive has fully cured before loading (see Working / Loading

Time chart below)

8. Clean up with acetone

Refer to Technical Data Sheet and MSDS available from

www.ramset.com.au, for precautions and further detailed

installation instructions

Working and Loading TimeSubstrate Temperature

(°C)

Gel Time

 (min)

Cure Time

(hours)

10 21 8

16 18 5

20 20 3

27 12 2.5

32 8.5 2

I   n  j    e  c t  i    o n 

A   d  h  

 e  s i   v  e  s 

Recommended Installation TemperaturesMinimum Maximum

Substrate 5°C 40°C

 Adhesive 20°C 32°C

ChemSet™ Reo 502™ - Indicative Working Loads in 32 MPa Concrete with ChemSet™ 

Anchor StudsThreadSize

Drilled HoleØ (mm)

Min HoleDepth (mm)

TighteningTorque (Nm)

Min EdgeDistance (mm)

Min AnchorSpacing (mm)

Max TensileLoad, Na (kN)

Max ShearLoad, V as

 (kN)*

M8 10 80 10 35 50 6.3 4.4

M10 12 90 20 40 60 10.3 7.1

M12 14 110 40 50 75 15.3 10.5

M16 18 125 95 65 100 29.4 19.9

M20 24 150 180 80 120 37.9 29.9

M20 24 170 180 80 120 43.0 29.9

M24 26 160 315 100 145 40.9 43.3

M24 26 210 315 100 145 53.6 43.3

M30 32 270 600 120 180 72.4 90.4+

M36 38 330 1050 145 220 101.5 131.7+

Bold working load values in tension are limited by steel. All other values limited by concrete and adhesive bond

* For shear acting towards a concrete edge please contact a Ramset Engineer for further design assistance+ M30 and M36 steel shear values are for Grade 8.8 carbon steel. All other values are for Grade 5.8 carbon steel.

For water saturated or under water holes, reduce tensile load capacity by 30%

Hole ConditionHole Condition Suitable

Dry Yes

Damp Yes

Wet Yes

Flooded Yes

Drill Bit Type

Carbide Yes

Diamond Core Yes

Hole Orientation

Vertical Down Yes

Horizontal Yes

Vertical Up (Overhead) Contact Ramset™

ChemSet™ Reo 502™ Anchoring AdhesiveDescription Part No Box Quantity

Jumbo Cartridge (750 ml) + 1 Nozzle REO502J 12

ChemSet™ Universal Applicator CUA 1

ChemSet™ Pneumatic Universal Applicator CUAPN 1

Mixing Nozzles for Epoxy with Extension ISNE 5

Mixing Nozzle Turbo (Easier Dispensing) ISNET 1

Hole Cleaning Pump HCP 1

Hole Cleaning Pump High Volume HCPHV 1

Hole Cleaning Brush 13 mm HCBT13 1

Hole Cleaning Brush 20 mm HCBT20 1

Hole Cleaning Brush 26 mm HCBT26 1

Description Part No Box Quantity

The design engineer should ensure the structural element is capable of supporting these loads.

Refer to Ramset™ Specifiers Resource Book for more information or explanation of technical data.

  Working load capacity was derived from characteristicultimate load capacity by applying the following factors:

  Tension: Concrete = 3, Steel = 2.2

  Shear: Steel = 2.5