corporate standard std 5023 - volvo
Post on 18-Dec-2021
10 Views
Preview:
TRANSCRIPT
Corporate Standard STD 5023,501
Issue date April 2004 Issue 7 Page 1(29)
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
RITNINGSREGLER DRAWING RULES
Symboler, beteckningar och allmänt ritsätt
Symbols, designations and general drawing methods
Orientering Orientation
Internationell eller nationell motsvarighet till denna
standard saknas.
There is no international or national equivalent to this
standard.
Denna utgåva skiljer sig från utgåva 6 genom att
standarden ej längre gäller för nykonstruktion.
This issue differs from issue 6 in that the standard no
longer applies to new design.
För nykonstruktion skall istället standarderna
STD 101-0005 och STD 5023,503 (Volvokoncernen)
samt standard VCS 5023,509 (Volvo Personvagnar
AB) användas.
For new designs, standards STD 101-0005 and
STD 5023,503 (Volvo Group) as well as standard
VCS 5023,509 (Volvo Car Corporation) shall be used.
Innehåll Contents
1 Omfattning och tillämpning 1 Scope and field of application
2 Allmänna regler om ritningsdata 2 General rules on drawing data
3 Projektionsmetoder och snittplan 3 Projection methods and cutting planes
4 Linjer, punkter, ytor och markeringar 4 Lines, points, surfaces and markings
5 Förenklad ritning av maskinelement 5 Simplified representation of machine elements
6 Måttsättning 6 Dimensioning
7 Koordinat- och referenspunktsystem 7 Coordinate systems and master location system
8 Toleranser 8 Tolerances
9 Konsekvensklasser (Fordringsklasser)
9 Consequence classes (Requirement classes)
10 Dokumentationskrav 10 Documentation requirements
11 Ytstruktur 11 Surface structure
12 Svetsning 12 Welding
13 Gängor 13 Screw threads
14 Formvaror 14 Stock shapes
15 Hårdhet och härddjup 15 Hardness and case depth
16 Symboler avseende tillverkning 16 Symbols used in connection with manufacture
17 Positionsnummer och ritningsändring 17 Item reference and drawing change
18 Uppgifter i fälten på ritningsblanketten 18 Information in the drawing sheet blocks
19 Hänvisning på ritning till denna standard 19 Reference on drawing to this standard
Corporate Standard STD 5023,501
Issue 7 Page 2
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
1 Omfattning och tillämpning 1 Scope and field of application
Denna standard innehåller grafiska symboler, be-
teckningar av exempelvis gängor, toleranser och
ytjämnheter samt generella exempel på ritsätt vilka
används på ritningar som produceras inom Volvo-
koncernen eller på uppdrag av något enskilt koncern-
företag. Standarden hänvisar vidare till de Volvo kon-
cernstandarder eller ISO-standarder som ger en full-
ständig definition av visade angivelser.
This standard contains graphic symbols, designations
of, e.g. screw threads, tolerances and surface rough-
ness as well as general examples of drawing methods
used on drawings produced within the Volvo Group or
at the request of some individual company within the
Volvo Group. The standard refers also to those Volvo
corporate standards and ISO standards that give the
complete definition of the representation shown.
Genom referens till denna standard på ritning: By referring to this standard on drawings:
gäller krav enligt de standarder som anges under
rubriken "Fastställd i standard" i de följande
avsnitten
the requirements specified in the standards that
are indicated under the heading "Established by
standard" in the following sections apply
är det möjligt att tolka de angivelser som standar-
den ger exempel på.
is it possible to interpret the indications that the
standard gives examples of.
Där använd ritningsangivelse inte finns exemplifierad i
denna standard, skall hänvisning till tillämpad
standard alltid finnas på den aktuella ritningen.
In those cases the drawing method used is not
exemplified in this standard, reference to the standard
applied shall always be given on the relevant drawing.
Denna standard ger endast en förenklad förklaring av
respektive ritningsangivelse. För fullständig tolkning
gäller alltid de standarder vilka hänvisas till i anslut-
ning till respektive exempel.
This standard gives only a simplified explanation of
the respective drawing indication. For a complete
interpretation, the standards referred to in connection
with the respective example always apply.
Vid eventuella skiljaktigheter mellan angivelser i den-
na standard och de standarder som angetts för deras
tolkning, gäller alltid de senare.
In case of any discrepancy between the indications
given in this standard and the standards referred to for
full interpretation, the latter always apply.
2 Allmänna regler om ritningsdata 2 General rules on drawing data
Om inget annat angivits på ritning eller i annat tillhö-
rande dokument är måttuppgifter uttryckta i millimeter.
Unless otherwise stated on the drawing or in the associ-
ated document, dimensions are given in millimetres.
Om inget annat angivits, generellt eller för enskild
uppgift, återger det tekniska underlaget objektet i sitt
färdiga utförande.
Unless otherwise indicated, generally or for a single
piece of information, the technical documentation
represents the object in its finished condition.
Enda undantaget från denna regel är M-gängor där
toleransen gäller före eventuell ytbeläggning.
The only exception from this rule is surface coated M-
threads where the tolerance applies before any surface
coating.
Skala
Om inget annat angivits generellt på ritningen, har
huvudskala 1:1 tillämpats. En lokalt angiven skala
gäller endast berörd vy eller berört snitt.
Scale
Unless otherwise indicated generally on the drawing,
main scale 1:1 has been applied. A locally indicated
scale applies only to the view or section concerned.
Projektionsmetod
Om inget annat angivits på ritningen har vyplacering
enligt metod E = första kvadrantens projektions-
metod tillämpats.
Projection method
Unless otherwise indicated on drawing, the views are
arranged in accordance with method E = first angle
projection method.
2.1 Allmänna principer för toleranskrav 2.1 General principles for tolerance requirements
För alla toleranssatta egenskaper på ritning och i
tillhörande dokumentation gäller STD 5060,012
Principer för toleranskrav.
For all toleranced properties on drawings and in
associated documentation STD 5060,012 Principles
for tolerance requirements applies.
Corporate Standard STD 5023,501
Issue 7 Page 3
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
2.2 Allmänna ytkrav 2.2 General surface requirements
För ytor som saknar ytjämnhetsangivelse gäller ytkrav
med hänsyn till använd tillverkningsmetod enligt STD
5068,04 Krav på ytstruktur - Angivelse på ritning.
If no surface roughness value is specified for a parti-
cular surface, surface requirements based on the pro-
duction method used apply in accordance with STD
5068,04 Surface texture requirements - Indication
on drawing.
3 Projektionsmetoder och snittplan
3 Projection methods and cutting planes
Ritsätt
Drawing method
Betydelse
Explanation
Fastställd i standard
Established by standard
1
Metod E. Första kvadrantens projektions-
metod/
Method E. First angle projection method
ISO 128
Metod A. Tredje kvadrantens projektions-
metod/
Method A. Third angle projection method
ISO 128
Symbol
Pilmetoden. Vyplacering enligt metod med
riktningspilar/
The arrow method. Layout of views according
to the reference arrow method
Fastställd genom denna
standard/
Established by this
standard
Princip / Principle
C
B
D
A
ISO 128
Ritning och måttsättning i axonometrisk
representation/
Drawing and dimensioning in axonometric
representation
STD 5023,35
Corporate Standard STD 5023,501
Issue 7 Page 4
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
Ritsätt
Drawing method
Betydelse
Explanation
Fastställd i standard
Established by standard
A
A
Markering av snittplan/
Indication of cutting plane
ISO 128
X2217
Beteckning av snitt i ett koordinatsystem (med
koordinaten för snittplanet) då snittplanet är
parallellt med någon av koordinataxlarna/
Identification of a section in a coordinate
system (with the coordinate for the cutting
plane) when the position of the cutting plane is
parallel with one of the coordinate axes
STD 5023,51
4 Linjer, punkter, ytor och markeringar
4 Lines, points, surfaces and markings
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
Linjers allmänna användning och betydelse/
General use and meaning of lines
ISO 128
Delvy av symmetriskt objekt. Två alternativa
ritsätt/
Partial view of a symmetrical object. Two
alternative methods of presentation
ISO 128
Brutna vyer. Två alternativa ritsätt/
Interrupted views. Two alternative methods of
presentation
ISO 128
Corporate Standard STD 5023,501
Issue 7 Page 5
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
Ritsätt
Drawing method Betydelse Explanation
Fastställd i standard Established by standard
Kontur före bearbetning (i detta fall före bock-ning)/ Outline before forming (in this case before bending)
ISO 128
Markering av kontur för intilliggande objekt/ Indication of outline of an adjacent part
ISO 128
Markering av bana för rörelse och alternativt
eller extremt läge för rörlig del/
Indication of trajectories and alternative or ex-
treme positions for movable parts
ISO 128
Markering av fyrkantiga ytor och ändar/
Indication of square surfaces and ends
ISO 128
Markering av vätska i snitt/
Indication of fluid in section
Fastställd genom denna
standard/
Established by this
standard
Markering av plåttjocklek på skalkonstruk-
tioner i vy respektive snitt/
Indication of sheet metal thickness in thin-
walled product design in view and section
respectively
STD 5023,51
Corporate Standard STD 5023,501
Issue 7 Page 6
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
Ritsätt
Drawing method Betydelse Explanation
Fastställd i standard Established by standard
Pil som ansluter snitt till aktuell koordinatlinje
då ett antal snitt (genom en lång artikel) med
konstanta koordinatvärden i två riktningar
upprepas i den tredje riktningen/
Arrow connecting a section to the relevant
coordinate line, when a number of sections
(through a long part) with constant coordinate
values in two directions are repeated in the
third direction
STD 5023,51
A
B
C
D
Markering av punkter på skalkonstruktioner/
Indication of points in thin-walled product
design
STD 5023,51
A B C
Markering av linjer på skalkonstruktioner/
Indication of lines in thin-walled product design
STD 5023,51
Markering av passningsyta till motgående
artikel/
Indication of mating surfaces to mating parts
Synlig passningsyta/
Visible mating surface
Skymd passningsyta/
Hidden mating surface
STD 5023,51
5 Förenklat ritning av maskin-element
5 Simplified representation of machine elements
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
Ritning av gängor/
Representation of screw threads
Utvändiga synliga gängor/
External visible screw threads
ISO 6410
Corporate Standard STD 5023,501
Issue 7 Page 7
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
Invändiga skymda gängor/
Internal hidden screw threads
Snitt genom invändiga gängor/
Section through internal screw threads
Ritning av kuggar / Representation of gears
ISO 2203
Symboler för kuggtyp och riktning/
Symbols for gear type and direction
Snedkugg höger och vänster/
Helical to the right and to the left
Dubbel snedkugg / Double helical
Bågkugg / Spiral
Ritning av splines och serrationer/
Representation of splines and serrations
Symbol för / Symbol for:
Splines med rak profil/
Straight-sided splines
Evolventsplines och serrationer/
Involute splines and serrations
ISO 6413
Corporate Standard STD 5023,501
Issue 7 Page 8
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
A) B) C)
Allmänt förenklad ritning av dynamiska
tätningar/
General simplified representation of dynamic
seals:
A) Tätningsriktning saknar betydelse/
Sealing direction of no importance
B) Tätningsriktning (i pilens riktning)/
Sealing direction (in the direction of the
arrow)
C) Verklig kontur visad / Exact contour shown
ISO 9222-1
Detaljerad förenklad ritning av radialtätningar/
Detailed simplified representation of lip type
seals (radial seals):
Tätning utan dammtunga för roterande
axel/
Rotary shaft seal without dust lip
ISO 9222-2
Tätning utan dammtunga för stillastående
axel och roterande hus/
Seal without dust lip for stationary shaft
and rotary housing
Tätning med dammtunga för roterande
axel/
Rotary shaft seal with dust lip
Tätning med dammtunga för roterande
axel (dubbelverkande)/
Rotary shaft seal with dust lip (double-
acting)
Detaljerad förenklad ritning av radialtätningar/
Detailed simplified representation of lip type
seals (radial seals):
Tätning med dammtunga för stillastående
axel och roterande hus/
Seal with dust lip for stationary shaft and
rotary housing
ISO 9222-2
Detaljerad förenklad ritning av axialtätningar/ Detailed simplified representation of axial seals
Axialtätning för roterande axel/ Rotary shaft axial seal
ISO 9222-2
Corporate Standard STD 5023,501
Issue 7 Page 9
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
Detaljerad förenklad ritning av tätningar för
fram- och återgående rörelser (kolvstångs-
tätningar)/
Detailed simplified representation of seals for
reciprocating movements (piston rod seals):
ISO 9222-2
A) B) C) D)
A) U-manschetter / U-cups
B) V-tätningssats / V packing sets
C) Hattmanschetter / V-rings
D) Avstrykare / Wipers
Detaljerad förenklad ritning av labyrinttät-
ningar/
Detailed simplified representation of labyrinth
seals
ISO 9222-2
A) B)
Förenklad ritning av rullningslager/
Simplified representation of rolling bearings
Ritas normalt enligt A). B) visar exempel på
förenklad ritning där lagrets verkliga kontur
visas/
Normally drawn in accordance with A). B)
shows an example of simplified representation
showing the exact outline of the bearing
ISO 8826-1
Styrpinne, styrhål, tyngdpunkt/ Guide pin, guide hole, centre of gravity
Fastställd genom denna standard/ Established by this standard
6 Måttsättning 6 Dimensioning
6.1 Måttsättning allmänt 6.1 General dimensioning
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
65±0,5
35±
0,5
Måttsättning, allmänna regler/
Dimensioning, general principles
ISO 129
60,5°±1,5°
Måttsättning av vinkelmått/
Dimensioning of angular dimensions
ISO 129
Corporate Standard STD 5023,501
Issue 7 Page 10
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
(55) Markering av hjälpmått/
Indication of auxiliary dimensions
ISO 129
50
Markering av bågmått/
Indication of arc dimensions
ISO 129
25
Markering av icke skalenligt mått/
Indication of dimension out-of-scale
ISO 129
Nollpunkt vid förenklad baslinjemåttsättning/
Origin indication in superimposed running
dimensioning
ISO 129
1250
Bruten måttlinje. Angivet mått avser mått från
nollpunkt för förenklad baslinjemåttsättning/
Interrupted dimension line. The indicated
dimension runs from the origin indication in
superimposed running dimensioning
Fastställd genom denna
standard/
Established by this
standard
25*-2+1
Markering av basmått vars värde bestäms av
aktuell modell, medan toleranserna bestäms
av ritningen (Ej för nykonstruktion)/
Indication of a basic size, the value of which
shall be taken from the model in question
while the tolerances are determined by the
drawing (Not for new design)
STD 5023,51
R25* R6*
X2200 X2280
Radie som förändras kontinuerligt mellan två
angivna koordinatvärden (Ej för nykonstruk-
tion)/
A radius, the value of which changes
continuously between two indicated coordinate
values (Not for new design)
STD 5023,51
25±1
Verkligt mått / True size
Exempelvis det verkliga måttet för ett
hål på en sluttande yta/
E.g. the correct dimension of a hole on
a surface that inclines
STD 5023,51
Corporate Standard STD 5023,501
Issue 7 Page 11
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
16
Inramade mått / Framed dimensions:
Inställningsmått för produktion och
kontroll. Dessa mått betraktas som
toleranslösa/
Setting dimension for production and
inspection. These dimensions shall be
considered as having no tolerances
Fastställd genom denna
standard /
Established by this
standard
I vissa fall för teoretiskt riktiga mått vid
tillämpning av form- och läge-
toleranser/
In some cases for theoretically exact
dimensions when using geometrical
tolerances
STD 5062,2
Mått till referenspunkter/
Dimensions to master location points
F6
F11
Hålnumrering / Numbering of holes
Hål betecknas med bokstäver och siffror där/
Holes designated by letters and figures where:
T = vy uppifrån / view from above
B = vy underifrån / view from below
F = vy framifrån (huvudvy)/
front view (principal view)
R = vy bakifrån / view from the rear
RH = vy från höger / view from the right
LH = vy från vänster / view from the left
STD 5023,95
6.2 Symboler i samband med mått 6.2 Symbols in connection with dimensions
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
Diameter ISO 129
R Radie / Radius ISO 129
Kvadrat / Square ISO 129
Avlångt hål / Oblong hole Fastställd genom denna standard/ Established by this standard
Angivelse av kona / Indication of taper ISO 3040
Corporate Standard STD 5023,501
Issue 7 Page 12
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
Rektangulär form / Rectangular shape Fastställd genom denna standard/ Established by this standard
SR Sfärisk radie / Spherical radius ISO 129
S Sfärisk diameter / Spherical diameter ISO 129
CL Centrumlinje / Centre line Fastställd genom denna standard/ Established by this standard
x Antalet lika element, exempelvis 5x10 för fem gånger måttet 10/ Number of equal elements, for example 5x10 for five times the dimension 10
ISO 129
6.3 Markering av krav 6.3 Marking of requirements
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
A) B)
Markering av partiellt krav, exempelvis härdning/
Indication of a partial requirement, for example
hardening
Är kravets utsträckning oväsentlig eller
självklar utelämnas måttsättning, se figur A)/
When the extension of the requirement is of
no importance or when it is obvious, the
dimensioning can be excluded, see figure A)
Vid behov måttsätts det speciella kravet, se
figur B)/
When needed, the special requirement shall
be dimensioned, see figure B)
ISO 129
3,2
Utsträckning av krav. Markering med en punkt-
streckad fin linje av att exempelvis ett mått, en
tolerans eller ett ytjämnhetskrav gäller för flera
ytor i samma plan/
Continuation of requirements. Indication with a
chain thin line to show that e.g. a dimension, a
tolerance or a surface requirement applies to
several surfaces in the same plane
Fastställd genom denna
standard/
Established by this
standard
Corporate Standard STD 5023,501
Issue 7 Page 13
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
ZONMARKERING / ZONE MARKING
Zonmarkering av område på en gjuten eller smidd
artikel. Inom det zonmarkerade området är de
tillåtna material- och/eller ytdefekterna
begränsade enligt standard som åberopas på den
aktuella ritningen/
Zone marking of an area on a cast or forged part.
Within the zone marked area, the allowed
material and/or surface defects are limited in
accordance with the standard referred to on the
relevant drawing
För artiklar i gjutjärn eller gjutstål anges
ordet "zonmarkering". Tolkning enligt
STD 1006,601. (Se figur)
For cast iron or steel parts the word "zone
marking" shall be indicated. Interpretation
in accordance with STD 1006,601. (See
figure)
För artiklar i gjutet aluminium anges zon-
och klassbeteckning enligt STD
1006,643/
For cast aluminium parts, zone and class
designation shall be indicated in
accordance with STD 1006,643
För smidda artiklar anges klass för ytkrav
enligt STD 1000,51/
For forged parts, surface requirements
shall be indicated in accordance with STD
1000,51
Fastställd genom denna
standard/
Established by this
standard
6.4 Benämning av håltyper vid skalkonstruktioner
6.4 Naming of hole types in thin-walled product design
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
FIXING HOLE
PROCESS HOLE / BCD
Tolkning av håltyper för skalkonstruktioner/
Interpretation of hole types for thin-walled product
design
Hål betecknade med följande namn har definierad
funktion och omfattas av särskilda regler:/
Holes designated by following names have
defined functions and are covered by particular
rules:
- Draining hole
- Fixing hole
- Clearance hole
- Locating hole
- Process hole
- Lightening hole
STD 5023,99
Corporate Standard STD 5023,501
Issue 7 Page 14
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
7 Koordinat- och referens-punktsystem
7 Coordinate systems and master location system
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
A)
ZM1500
B)
ZE1500
Koordinatsystem för tunga fordon/
Coordinate systems for heavy vehicles
A) Z-koordinat i huvudkoordinatsystemet (M)/
Z coordinate in the main coordinate
system (M)
B) Z-koordinat i separat koordinatsystem för
motor (E). Separata system finns även
för hytt (C) och ram (F)/
Z coordinate in a separate coordinate
system for the engine (E). There are also
separate systems for the cab (C) and
the frame (F)
STD 5026,1
A)
XFA0
B)
XRA0
Koordinatsystem för tunga fordon, särskild
tillämpning för bussar där X-axeln har två
nollpunkter/
Coordinate systems for heavy vehicles, special
application for buses where the X-axis has two
origins.
A) X-axelns nollpunkt genom framaxeln/
Origin for the X-axis through the front axle
B) X-axelns nollpunkt genom bakaxeln/
Origin for the X-axis through the rear axle
STD 5026,1
X1500
Koordinatsystem för personvagnar/
Coordinate systems for cars
X-koordinat i huvudkoordinatsystem/
X coordinate in the main coordinate
system
STD 5026,11
STD 5026,12 (V40)
STD 5026,13
(Renault/Volvo)
X2
200
Koordinatsystem för personvagnar/
Coordinate systems for cars
X-koordinat i ett hjälpkoordinatsystem/
X coordinate in an auxiliary coordinate
system
STD 5026,11
Z1530
X1560
Angivelse av koordinater som ej är jämna
hundratal/
Indication of coordinates that are not in even
hundreds
STD 5026,1
Corporate Standard STD 5023,501
Issue 7 Page 15
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
X1500
Angivelse av riktning från noll för en ensam
koordinatlinje/
Indication of direction from zero for a single
coordinate line
STD 5023,51
Referenspunkt i referenspunktsystem. Triangeln
ritas antingen fylld eller rutmönstrad/
Master location point in master location system.
The triangle shall be drawn filled or cross
hatched
STD 5026,2
Stödpunkt i referenspunktsystem/
Location point in master location system
STD 5026,2
Kontrollpunkt i referenspunktsystem/
Inspection point in master location system
Mätpunkt som varit referenspunkt i tidigare
processtadium/
Measuring point which has been a master
location point at a previous stage in the
process
STD 5026,2
Referenspunkt i delsystem som också är
kontrollpunkt i huvudsystemet/
Master location point in a subordinate system
that also is a measuring point in the master
system
STD 5026,2
8 Toleranser 8 Tolerances
8.1 Dimensionstoleranser 8.2 Dimensional tolerances
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
0,5 Tolerans för linjärt mått/
Tolerance for linear dimension
STD 5060,012
+ 1,5 0
Tolerans för vinkelmått (del av grad i
decimaler)/
Tolerance for angular dimension (fraction of
degree in decimals)
STD 5060,012
+0,160 H11 0
ISO-tolerans (hål)/
ISO tolerance (holes)
STD 5061,1
Corporate Standard STD 5023,501
Issue 7 Page 16
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
0 h10 -0,100
ISO-tolerans (axlar)
ISO tolerance (shafts)
STD 5061,1
E
Enveloppkrav / Envelope requirement STD 5060,012
8.3 Form- och lägetoleranser 8.3 Geometrical tolerances
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
Ø0,5AI
Toleransrektangel med exempel på uppgifter/
Tolerance frame with example of information:
Mätprincip / Measuring principle
Referens / Datum
Toleransvärde / Tolerance value
Toleranssatt egenskap/
Toleranced characteristic
STD 5062,2
Rakhet / Straightness STD 5062,2
Planhet / Flatness STD 5062,2
Rundhet / Circularity STD 5062,2
Cylindricitet / Cylindricity STD 5062,2
Profilform / Profile of any line
Profilläge / Position of any profile
(med referenselement / with datum feature)
STD 5062,2
Profilriktning / Orientation of any profile STD 5062,25
Ytform / Profile of any surface
Ytläge / Position of any surface
(med referenselement / with datum feature)
STD 5062,2
Ytriktning / Orientation of any profile STD 5062,25
Corporate Standard STD 5023,501
Issue 7 Page 17
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
Lägeriktighet / Position STD 5062,2
Lägeriktning / Orientation of position STD 5062,25
Koncentricitet, koaxialitet /
Concentricity, coaxiality
STD 5062,2
Symmetri / Symmetry STD 5062,2
Parallellitet / Parallelism STD 5062,2
Vinkelräthet / Perpendicularity STD 5062,2
Vinkelriktighet / Angularity STD 5062,2
Kast / Run-out STD 5062,2
Totalkast / Total run-out STD 5062,2
I XI
Mätprinciper / Measuring priciples
Exempel på angivelse av mät-
principerna 1 och 11/
Example of indicating measuring
principles 1 and 11
STD 5062,2
STD 5062,25
A
Angivelse av referens med referensbokstav/
Indication of datum with datum letter
STD 5062,15
Angivelse av referens utan referensbokstav/
Indication of datum without datum letter
STD 5062,15
Corporate Standard STD 5023,501
Issue 7 Page 18
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
A1
Lokal referens / Datum target
Exempel: lokal referenspunkt A1/
Example: datum target point A1
STD 5062,15
B1
Exempel: lokal referenslinje B1/
Example: datum target line B1
A1
Ø8
Exempel: lokal referensarea A1, 8
Example: datum target area A1, 8
B2
20x20
Exempel: lokal referensarea B2, 20x20
Example: datum target area B2, 20x20
P
Utflyttat toleransområde/
Projected tolerance zone
STD 5062,2
Spelvariation / Clearance STD 5062,25
M
Måttjämkning / Maximum material principle STD 5062,4
Corporate Standard STD 5023,501
Issue 7 Page 19
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
9 Konsekvensklasser (Fordringsklasser)
9 Consequence classes (Requirement classes)
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
1 Konsekvensklass 1/
Consequence class 1
STD 5060,3
2 Konsekvensklass 2/
Consequence class 2
STD 5060,3
3 Konsekvensklass 3/
Consequence class 3
STD 5060,3
4 Konsekvensklass 4 /
Consequence class 4
STD 5060,3
Fordringsklass 1 med dokumentationsplikt/
Requirement class 1 with documentation
liability
STD 5060,4
Ej för nykonstruktion/
Not for new design
2D Fordringsklass 2 med dokumentationsplikt/
Requirement class 2 with documentation
liability
STD 5060,4
Ej för nykonstruktion/
Not for new design
2R Fordringsklass 2 med dokumentationsplikt
endast avseende resultatdokumentation/
Requirement class 2 with documentation
liability regarding results records only
STD 5060,4
Ej för nykonstruktion/
Not for new design
2P Fordringsklass 2 med information om
processkrav/
Requirement class 2 with information on
process requirements
STD 5060,4
Ej för nykonstruktion/
Not for new design
3P Fordringsklass 3 med processkrav/
Requirement class 3 with process require-
ments
STD 5060,4
Ej för nykonstruktion/
Not for new design
10 Dokumentationskrav 10 Documentation requirements
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
CR
Krav på fullständig dokumentation/
Requirement for complete documentation
STD 5032,2
RR
Krav på resultatdokumentation/
Requirement for results records
STD 5032,2
Corporate Standard STD 5023,501
Issue 7 Page 20
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
11 Ytstruktur 11 Surface texture
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
SLIPAD/GROUND
0,25
M0,4
0,2
Exempel på ytjämnhetsangivelse/
Example of indication of surface roughness:
Grundsymbol vid krav på bearbetning
Basic symbol at requirement for machining
Ra 0,4 m
Krav på viss tillverkningsmetod
Requirement for a certain production method
Referenslängd / Sampling length
Bearbetningsspårens riktning
Direction of lay
Bearbetningstillägg / Machining allowance
STD 5068,04
A) B) C)
A) Grundsymbol för ytstrukturkrav/
Basic symbol for surface texture
requirements
B) Krav på avverkande bearbetning/
Requirement for removal of material by
machining
C) Förbud mot avverkande bearbetning/
Prohibition against removal of material by
machining
STD 5068,04
A) B)
3,2 Rz 6,3
A) Ytjämnhetskrav, parameter Ra/ Requirement for surface roughness parameter Ra
B) Ytjämnhetskrav, annan parameter än Ra. Exemplet visar Rz/ Requirement for surface roughness, other parameter than Ra. The example shows Rz
STD 5068,04
A) B) C)
= X
D) E) F)
M C R
Bearbetningsspårens riktning / Direction of lay:
A) Parallella med projektionsplanet/
Parallel to the plane of projection
B) Vinkelräta mot projektionsplanet
Perpendicular to the plane of projection
C) Två korsande sneda riktningar relativt
projektionsplanet/
Crossed in two oblique directions relative to
the plane of projection
D) Ingen dominerande riktning
Multi-directional
E) Koncentriska / Concentric
F) Radiella / Radial
STD 5068,04
Corporate Standard STD 5023,501
Issue 7 Page 21
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
SLIPAD/GROUND
Krav på viss bearbetningsmetod, exemplet visar
krav på slipning/
Requirement for a certain production method, the
example shows requirement for grinding
STD 5068,04
12 Svetsning 12 Welding
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
1)2)
3) 4)
Svets AWeld A
Svets BWeld B
1) 3)
2) 4)
Beteckning / Designation
Exempel på pilsida och bortre sida/
Examples of arrow side and other side:
1) Pilsida för svets A, Arrow side for weld A 2) Bortre sida för svets A, Other side for weld A 3) Pilsida för svets B, Arrow side for weld B 4) Bortre sida för svets B, Other side for weld B
STD 5605,5
a5
a5
8x90
7x90
(200)
(200)11 - B [3]
Exempel på svetsbeteckning/
Example of a symbolic representation of weld:
Konsekvensklass / Consequence class
Svetsklass / Welding class
Svetsmetod / Welding process
Avstånd mellan delsvetsar/
Distance between weld elements
Symbol för sicksacksvets/
Symbol for staggered intermittent weld
Delsvetslängd / Length of weld elements
Antal delsvetsar / Number of weld elements
Tilläggssymbol / Supplementary symbol
Grundsymbol / Elementary symbol
Mått på svetsens tvärsnitt
Dimension of weld cross-section
STD 5605,5
Corporate Standard STD 5023,501
Issue 7 Page 22
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
A) B) C) D)
E) F) G) H)
I) J) K)
Grundsymboler / Elementary symbols:
A) Svets i dubbelflänsad stumfog/
Butt weld between plates with raised edges
B) Svets i I-fog och svets i kantfog/
Square butt weld
C) Svets i V-fog / Single-V butt weld
D) Svets i halv V-fog / Single-bevel butt weld
E) Svets i U-fog / Single-U butt weld
F) Svets i J-fog / Single-J butt weld
G) Baksträng / Backing run
H) Svets i kälfog / Fillet weld
I) Svets i hålfog / Plug weld
J) Punktsvets / Spot weld
K) Sömsvets / Seam weld
STD 5605,5
Tilläggssymboler / Supplementary symbols:
Struken svets / Flat weld
Rågad svets / Convex weld
Urgröpt svets / Concave weld
STD 5605,5
Kompletterande beteckningar/
Complementary indications:
Montagesvets / Site weld
Svets runt om ett objekt/
Peripheral weld (all around a part)
STD 5605,5
Corporate Standard STD 5023,501
Issue 7 Page 23
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
13 Gängor 13 Screw threads
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
Exempel på en fullständig gängbeteckning/
Example of a complete thread designation
Metrisk grovgänga / Metric coarse thread
STD 5081,15
M8 - 6e Tolerans för utvändig gänga (före
ytbehandling)/
Tolerance for external thread (before
coating)
M8x1- 6e Exempel på beteckning för utvändig metrisk
fingänga (före ytbehandling)/
Example of a designation of an external metric
fine thread (before coating)
M8 - 6H Exempel på beteckning för invändig metrisk
gänga (ej ytbelagd)/
Example of a designation of an internal metric
thread (not coated)
M8 - ud25 Exempel på beteckning av utvändig metrisk
grovgänga som underdimensionerats för
varmförzinkning/
Example of a thread designation for an
external metric coarse thread, undersized for
hot dip galvanizing
STD 5081,151
M8x1k Special Exempel på beteckning av utvändig konisk
metrisk gänga/
Example of designation of an external taper
metric screw thread
STD 5081,25
Exempel på en fullständig gängbeteckning/
Example of a complete thread designation
PL-gänga / PL thread
STD 5081,45
PL16 - 7h Tolerans för utvändig gänga
Tolerance for external thread
3/4-14 NPTF
Exempel på utvändiga Dryseal rörgängor/
Examples of external Dryseal pipe threads:
- Konisk rörgänga, typ NPTF/
Taper pipe thread, type NPTF
STD 5081,711
1/4 - 18 PTF-SPL Short - Konisk rörgänga, typ PTF-SPL Short
Taper pipe thread, type PTF-SPL Short
STD 5081,713
Corporate Standard STD 5023,501
Issue 7 Page 24
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
3/4-14 NPTF
Exempel på invändiga Dryseal rörgängor/
Examples of internal Dryseal pipe threads:
- Konisk rörgänga, typ NPTF/
Taper pipe thread, type NPTF
STD 5081,721
3/4-14 NPSF - Cylindrisk rörgänga, typ NPSF/
Parallel pipe thread, type NPSF
STD 5081,731
14 Formvaror 14 Stock shapes
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
Rund / Round Fastställd genom denna
standard/
Kvadratisk / Square Established by this
standard
Rektangulär / Rectangular
L-profil / L-profile
I-profil / I-profile
T-profil / T-profile
U-profil / U-profile
Z-profil / Z-profile
Corporate Standard STD 5023,501
Issue 7 Page 25
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
15 Hårdhet och härddjup 15 Hardness and case depth
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
350 HBS
Beteckning för Brinellhårdhet/
Designation of Brinell hardness:
Brinellhårdhet 350 bestämd med stålkula
(tidigare betecknad HB). HBW betecknar
brinellhårdhet bestämd med
hårdmetallkula/
Brinell hardness 350 determined with a
steel ball (previously denoted HB). HBW
denotes the Brinell hardness determined
with a hard metal ball.
STD 1014,311
600 HBW 5/750/20
Vid behov kompletteras beteckningen med/
When needed, the designation is supple-
mented with:
Kuldiameter (mm) / Ball diameter (mm)
Massa (kg) som åstadkommer provkraften/
Mass (kg) that yields the test force
Hålltid (s)/
Duration of test force application (s)
59 HRC
Beteckning för Rockwellhårdhet/
Designation of Rockwell hardness:
Rockwellhårdhet 59 bestämd enligt
Rockwellskala C/
A Rockwell hardness of 59, measured on
the Rockwell C-scale
STD 1014,312
640 HV
Beteckning för Vickershårdhet/
Designation of Vickers hardness:
Vickershårdhet 640 / Vickers hardness 640
STD 1014,316
640 HV 30/20
Vid behov kompletteras beteckningen med /
When needed, the designation is supple-
mented with:
Massa (kg) som åstadkommer provkraften/
Mass (kg) that yields the test force
Hålltid (s)/
Duration of test force application (s)
Corporate Standard STD 5023,501
Issue 7 Page 26
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
DC = 1,2 0,3
Beteckning för sätthärdningsdjup/
Designation of case-hardened depth:
Sätthärdningsdjup 1,2 0,3/
Case-hardened depth 1,2 0,3
STD 1019,434
+ 0,2 DC 650 = 0,4 - 0,1
Krav på annan gräns för sätthärdningsdjupet
än 550 HV anges enligt nedanstående
exempel/
Requirement for another hardness limit for the
case-hardened depth than 550 HV shall be
indicated as in the example below:
Sätthärdningsdjup 0,4 +0,2/-0,1 vid
650 HV /
Case-hardened depth 0,4 +0,2/-0,1 at
650 HV
DI = 2 1
Beteckning för induktionshärdningsdjup/
Designation of induction-hardened depth:
Induktionshärdningsdjup 2 1/
Induction-hardened depth 2 1
STD 1019,432
DI 500 = 2 1
Krav på annan gräns för induktions-
härdningsdjupet än 400 HV anges enligt
nedanstående exempel/
Requirement for another hardness limit for the
induction-hardened depth than 400 HV shall
be indicated as in the example below:
Induktionshärdningsdjup 2 1 vid 500 HV/
Induction-hardened depth 2 1 at 500 HV
DNC = 0,3 MIN
Beteckning för nitrokarbureringsdjup/
Designation of nitrocarburizing depth:
Nitrokarbureringsdjup 0,3 MIN/
Nitrocarburizing depth 0,3 MIN
STD 1019,438
DN = 0,4 0,1
Beteckning för nitrerdjup/
Designation of nitriding depth:
Nitrerdjup 0,4 0,1/
Nitriding depth 0,4 0,1
STD 1019,436
DN 450 = 0,4 0,1
Krav på annan gräns för nitrerdjupet än
400 HV anges enligt nedanstående exempel/
Requirement for another hardness limit for the
nitriding depth than 400 HV shall be indicated
as in the example below:
Nitrerdjup 0,4 0,1 vid 450 HV/
Nitriding depth 0,4 0,1 at 450 HV
Corporate Standard STD 5023,501
Issue 7 Page 27
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
16 Symboler avseende tillverkning 16 Symbols used in connection with manufacture
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
Markering av yta som ej skall lackeras/
Marking of surface not to be painted
Fastställd genom denna
standard/
Established by this
standard
Markering av delning (partning) av smides-
verktyg, gjutformar etc./
Marking the parting of forging tools, casting
moulds etc.
Fastställd genom denna
standard/
Established by this
standard
Markering av första uppspänning/
Marking of first clamping
Fastställd genom denna
standard/
Riktning mot ritningsplanet
Direction towards the drawing plane
Established by this
standard
Riktning från ritningsplanet
Direction from the drawing plane
Markering av idragning/
Marking of tightening
Fastställd genom denna
standard/
Riktning mot ritningsplanet
Direction towards the drawing plane
Established by this
standard
Riktning från ritningsplanet
Direction from the drawing plane
17 Positionsnummer och ritnings-ändring
17 Item reference and drawing change
Ritsätt Drawing method
Betydelse Explanation
Fastställd i standard Established by standard
10
Positionsnummercirkel / Item reference circle Fastställd genom denna
standard/
Established by this
standard
14
Markering på ritningen i närheten av
genomförd ändring (görs vid behov).
Ändringsnotens nummer anges i triangeln/
Indication (when needed for clarity) on the
drawing, close to a change made. The number
of the change note shall be indicated in the
triangle
Fastställd genom denna
standard/
Established by this
standard
Corporate Standard STD 5023,501
Issue 7 Page 28
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
18 Uppgifter i fälten på ritnings-blanketten
18 Information in the drawing sheet blocks
För tolkning av uppgifter i ritningsblankettens huvud-
respektive ändringsfält hänvisas till följande
standarder:
For interpretation of information in the title and
revision blocks of the drawing sheet, see the following
standards:
ritningsblankett med huvudfält enligt figur 1, se
STD 5021,25. Ej för nykonstruktion.
ritningsblankett med huvudfält enligt figur 2, se
STD 5021,23.
ritningsblankett med huvudfält enligt figur 3, se
STD 5021,21.
ritningsblankett med huvudfält enligt figur 4, se
STD 5021,2.
drawing sheet with title block in accordance with
figure 1, see STD 5021,25. Not for new design.
drawing sheet with title block in accordance with
figure 2, see STD 5021,23.
drawing sheet with title block in accordance with
figure 3, see STD 5021,21.
drawing sheet with title block in accordance with
figure 4, see STD 5021,2.
SIGN
DATUM
RITAD GODK DESIGN HÅLLF STAND GRANSKAD GODK PROD RITN. NR / DRAWING NO BLAD/
SHEETUTGÅVA / ISSUE
BENÄMNING / NAME
FORM- OCH LÄGETOLERANSER
GEOMETRICAL TOLERANCES
STD5062,2
YTJÄMNHET Ra µm
SURFACE ROUGHNESS Ra µm
STD
5068,04
STD
5060,011
STD
5062,4
STD
5061,003
STD
5060,4
TOLERANSKRAV
TOLERANCE REQUIREMENTS
SKALA /SCALE
PROJ.
GRUPP / GROUPAVD / DEPT.
REF.
UTG DIMENSION / BASICDIMENSION
DOKUMENT / DOCUMENT
BETECKNING /DESIGNATION.
TEKNISK
BESTÄMMELSE
TECH. REG.
VOLVO
MÅTTJÄMKNING
MAX MTRL. PRINCIPLE
FÖR EJ FORDRINGSKLASSMARKERADE EGENSKAPER
TO PROPERTIES NOT MARKED WITH REQUIREMENT CLASS
GRUNDLÄGGANDE TOL.PRINCIP
FUNDAMENTAL TOL. PRINCIPLE
KOMPLETT NR/
ASSY NO.
ARTIKEL NR/PART NO.
EJ FÖR NYKONSTRUKTION / NOT FOR NEW DESIGN
Fig. 1
TEKN BEST NR / TECH. REG.NO
RITAD / DRAWN
BENÄMNING
TITLE
FUNC. GROUP
DOKUMENTTYP
DOCUMENT TYPE
RITNING NR / DRAWINGNO
UTGÅVA / ISSUE BLAD / SHEET
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATIONNOTICE.
AND SHALL NOT BE USED OR REPRODUCED OR ITS CONTENTS
DISCLOSED, IN WHOLE OR IN PART, WITHOUT THE PRIOR WRITTEN
CONSENT OF THE VOLVO CAR CORPORATION.
Volvo Car Corporation
AVD / DEPT.SKALA / SCALE
PROJECTION GODKÄND / APPROVED
Fig. 2
Corporate Standard STD 5023,501
Issue 7 Page 29
NOT FOR NEW DESIGN AS OF 2004-04-01 This standard is valid when there is a reference to it. ”Not for new design” is only an indication to our design departments.
SIGN
DATE
DRAWN APPR. CHECKED SHEET DRAWING No ISSUE
NAME
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION AND SHALL
NOT BE USED OR REPRODUCED OR ITS CONTENTS DISCLOSED
IN WHOLE OR IN PART, WITHOUT THE PRIOR WRITTEN CONSENT OF Volvo Truck Corporation or Volvo GM Heavy Truck Corporation
NOTICE
E FIRST ANGLEPROJECTION
Volvo Truck Corporation
DEPT MODEL / PROJECT GROUP
REF.
BASIC DIMENSION
DOCUMENT
DESIGNATION
TECHNICAL REGULATION
SCALE
SYMBOLS, DESIGNATIONS AND STD
5023,501
SIGN
APPR. PROD
DATE PART NUMBER ISSUE
GENERAL DRAWING METHODS
CLASS MASTER No
Fig. 3 - Blanketten finns i ett antal versioner med samma layout men med olika företagsnamn The form exists in a number of versions with the same layout but with different company names
Volvo Truck Corporation
The copying, distribution and utilization of this document as well as the communication of its contents to others without expressed authorization is prohibited. Offenders will be held liable for payment of damages. All rights reserved in the event of the grant of a patent, utility model or ornamental design registration.
Document title
Document type
Document No Issue index Sheet No
Owner domain:Document prefix
Fig. 4 - Blanketten finns i ett antal versioner med samma layout men med olika företagsnamn The form exists in a number of versions with the same layout but with different company names
19 Hänvisning på ritning till denna standard
19 Reference on drawing to this standard
Vid tillämpning av denna standard skall hänvisning
ges i ritningens huvudfält eller genom not i ritningens
skrivfält enligt nedan:
For the application of this standard a reference in
accordance with below shall be given in the title block
of the drawing or as a note in the text block of the
drawing.
SYMBOLS, DESIGNATIONS AND GENERAL DRAWING METHODS STD 5023,501
top related