dietrich catalog
Post on 20-Oct-2015
170 Views
Preview:
TRANSCRIPT
■ Interior Framing
■ Exterior Framing
■ Floor Framing
■ Truss Framing
■ Fire-Rated Assemblies
■ Metal Beads & Trims
■ Vinyl Beads & Trims
■ Paper-Faced Beads & Trims
■ Veneer, Stucco & PlasterBeads & Trims
■ Metal Lath
The place to stop…before the building starts!SM
Dietrich Metal Fram
ing The M
etal Framing & Finishing Catalog
A Worthington Industries Com
pany
About Worthington IndustriesWorthington Industries is a leading diversified metal processing company with annual sales of approximately$3 billion. The Columbus, Ohio, based company is North America’s premier value-added steel processor and aleader in manufactured metal products such as metal framing, metal ceiling grid systems, pressure cylinders,automotive past model service stampings and laser welded blanks. The company employs more than 8,000people and operates 64 facilities in 10 countries
©Copyright 2008 by Dietrich Metal Framing. All rights reserved. DMF8/2008Printed in USA Form# 146 35M 10-08
Plant LocationsCorporate Headquarters
200 Old Wilson Bridge Rd.
Columbus, OH 43085
800-873-2604
Arizona Phoenix ............... 602-447-0204
California Colton ................ 909-824-9717
Stockton .............. 209-547-9066
Colorado Denver ................ 303-289-4092
Florida Miami .................. 305-652-5423
Georgia McDonough........ 678-304-5500
Hawaii Kapolei ................ 808-682-5747
Illinois Joliet ................... 815-207-0110
Indiana Hammond ........... 219-931-3741
Kansas Lenexa ................ 913-599-2026
Maryland Baltimore............. 410-477-8700
Massachusetts Lunenburg........... 978-342-9742
New Jersey Boonton............... 973-335-3240
Ohio Warren ................ 330-372-4014
Texas Baytown .............. 281-383-1617
Hutchins .............. 972-225-1100
Washington Renton ................ 425-251-1497
International Miami .................. 305-652-5423
Clip Express ............................866-638-1908
Other Dietrich Locationsand DivisionsDietrich Metal Framing Canada ..... 780-437-1763
Accelerated Building Technologies 412-490-5037
Aegis Metal Framing ...................... 314-851-2200
Vinyl Corp. ...................................... 800-648-4695
Dietrich Design Group North .......... 800-873-2443
or ............................... 219-853-9474
Dietrich Design Group South.......... 800-873-2443
or .............................. 678-304-5525
Dietrich Design Group West ........... 800-873-2443
or .............................. 760-931-0465
dietrich metalframing •com
Cold-Formed steel framing is recognized as a recycled content product.
Front DMF07_OBCOFC:DMF07_OBCOFC 7/16/10 4:09 PM Page 1
INTRODUCTIONDietrich Metal Framing is the largest producer of metal framingand finishing products in the world. As the industry leader,Dietrich offers the best of products, brands, systems, servicesand companies to provide the construction industry with com-prehensive, innovative, low-cost, single-source procurement,supply and building solutions. Dietrich believes leadership isabout action — not simply position. That’s why we continuallystrive to expand our existing markets, develop framingtechnologies, create value-added systems and introduce count-less new products to meet the ever-changing demands of thebuilding and construction industry.
The Products We MakeDietrich Metal Framing is your total source for light-gauge framing and finishing products,systems, services and solutions. Dietrich is your one-stop source for the industry’s widestselection of wall, floor and truss framing, metal, vinyl, veneer and stucco finishing beadsand trims, and a full array of plaster and lath products. We deliver the highest-quality fram-ing and finishing products anywhere in the world. Dietrich delivers everything you need tokeep costs down and productivity up.
■ Axial & Curtain-Wall Framing■ Interior, Nonstructural Framing■ Shaftwall & Area Separation Wall■ Fire-Rated Assemblies■ Floor & Roof Truss Systems■ Deflection Systems■ Metal, Vinyl, Paper-Faced & Veneer Beads and Trims■ Control & Expansion Joints■ Metal Lath & Barrier Mesh■ Stucco & Plaster Beads and Trims■ Prefabricated & Turnkey Building Solutions■ Clips, Connectors & Fasteners
The Value You ReceiveWe provide our customers with a wide rangeof benefits such as supplier consolidation, product rationalization and integrated supplyprograms. Here’s what you can expect:
■ Code Compliant Products
■ Industry’s Broadest Product Line
■ Superior Quality
■ Local Manufacturing with GlobalDistribution
■ Innovative Products, Systems & Services
■ The Most-Specified Light-GaugeManufacturer
■ Best of Brands, Systems & Services
■ Exceptional Customer Care
■ Expert Sales & Field ServiceRepresentatives
■ Professional Technical & DesignAssistance
■ Expert Product Training
The place to stop…before the building starts!SM
www.dietrichmetalframing.com is one of the most advanced
resources for metal framing information in the industry. From
extensive product information to on-line catalogs, to video
installations, this site is your resource to building better, faster
and more profitably. Simply click on any one of our animated
value-added product assemblies for your own personal product
demonstration. You are one click away from adding more profit
to your bottom line.
This website is packed with everything from a basic introduction
to metal framing to elaborate design and productivity tools
including the member sizer program. The construction docu-
ments library features everything from
downloadable/customizable
specifications, certifications,
MSDS, to ICC code approvals.
Looking for alternative
building details, you will
find one of the industry’s
most extensive light-gauge
CAD libraries. This library
is filled with framing alter-
natives that improve effi-
ciency and drive profit to
your bottom line.Need submittals?Dietrich’s on-line submittal system is the easiest way to create
job submittals. Point, click and print for fast, professional
project submittals.
We make it easy for you to do business!
request a quote online @
dietrichmetalframing•
DMF07_IFCIBC:DMF07_IFCIBC 7/15/10 5:06 PM Page 1
1
What’s InsideSection Page(s)
Overview . . . . . . . . . . . . . . . . . . . . 1–20
Interior Framing . . . . . . . . . . . . . 21–58
Exterior Framing. . . . . . . . . . . . 59–114
Floor Framing . . . . . . . . . . . . . 115–134
Truss Framing. . . . . . . . . . . . . 135–140
Fire-Rated Assemblies . . . . . . 141–148
Metal Beads & Trims . . . . . . . 149–172
Vinyl Beads & Trims . . . . . . . . 173–186
Paper-Faced Beads & Trims. . 187–200
Veneer, Stucco & Plaster Beads & Trims. . . . . . . . . . . 201–224
Metal Lath. . . . . . . . . . . . . . . . 225–235
Index . . . . . . . . . . . . . . . . . . . . 236–241
Material Certification . . . . . . . 242–243
LEED ® Certification. . . . . . . . . . . . . 244
Your Best Value™
Build better, faster and more profitably with thesehigh-performance products, systems and services.Look for the BEST VALUE™ icons located throughoutthis catalog.
The Projects We SupplyCOMMERCIAL■ High-Rise
■ Mid-Rise
■ Low-Rise
■ Retail
■ Office Buildings
■ Hotels/Motels
INSTITUTIONAL■ Universities
■ Schools
■ Medical Centers
■ Religious
■ Hospitals
RESIDENTIAL■ Single Family
■ Multi-Family
■ Assisted Living
■ Military Housing
■ Manufactured & Modular Housing
■ Apartments & Condominiums
We Go the Extra MileWe work hard to make it easy for you to do business. From our state-of-the-art manufacturingto sophisticated quality control processes, to faxed order confirmations, we do more so you don’thave to.
Cover photo courtesy of GQ Contracting
DMF07_001:DMF07_001 6/30/10 4:05 PM Page 1
2
Denver
Phoenix
Colton
Stockton
Renton
Kapolei, HI
thePEOPLEwe SERVE
Whether you’re an architect, engineer, contractor, builder,supplier or a do-it-yourselfer, Dietrich is the one-stop sourcefor framing and finishing solutions. From design to installationassistance, we provide the products, pricing, innovation, technical support and superior service to make each and everyproject a total success.
Fast, Flexible and Responsive ServiceDietrich Customer Care Representatives are readily available to respond to your urgentproduct needs. Call, fax or e-mail your needs, questions or problems and we will deliver.Count on Dietrich to stock the products you need at competitive prices. We strive to fillstock orders within 24–48 hours.
Need custom packaging, small skid quantities, special skid markings or cut-to-length product? We custom make, pack, label and ship to your exact specifications. Price is important — service even more. Our services include:
■ Full or LTL Deliveries
■ Route Truck Delivery Service
■ One-Stop Shopping
■ Cut-to-Length
■ Specialized Packaging and Loading
■ Skid Labeling
■ Floor Breakdowns
■ Custom Part Fabrication
DMF07_002-003:DMF07_002-003 6/30/10 3:21 PM Page 2
3
Your Local SupplierWith more manufacturing and service locations strategically positioned throughout North America, we’re your local company ready to deliver what you need, when you need it.Many customers require technical engineering support, breadth of products and procurementsourcing programs unavailable from smaller regional or local competitors.
Manufacturing and Sales Locations
United StatesArizona Phoenix ............... 602-447-0204
California Colton ................ 909-824-9717
Stockton .............. 209-547-9066
Colorado Denver ................ 303-289-4092
Florida Miami .................. 305-652-5423
Georgia McDonough........ 678-304-5500
Hawaii Kapolei ................ 808-682-5747
Illinois Joliet ................... 815-207-0110
Indiana Hammond ........... 219-931-3741
Kansas Lenexa ................ 913-599-2026
Maryland Baltimore............. 410-477-8700
Massachusetts Lunenburg........... 978-342-9742
New Jersey Boonton............... 973-335-3240
Ohio Warren ................ 330-372-4014
Texas Baytown .............. 281-383-1617
Hutchins .............. 972-225-1100
Washington Renton ................ 425-251-1497
International Miami .................. 305-652-5423
Clip Express ........................... 866-638-1908
CanadaEdmonton ....................................... 780-469-9850Toronto ........................................... 905-565-9665Vancouver ...................................... 604-434-3737
Other Dietrich DivisionsDietrich Metal Framing Canada ..... 780-437-1763
Accelerated Building Technologies 412-490-5037
Aegis Metal Framing ...................... 314-851-2200
Vinyl Corp. ...................................... 800-648-4695
Dietrich Design Group North .......... 800-873-2443
or ............................... 219-853-9474
Dietrich Design Group South.......... 800-873-2443
or .............................. 678-304-5525
Dietrich Design Group West ........... 800-873-2443
or .............................. 760-931-0465
Dietrich Metal Framing, a Worthington Industries Company, is the leading manufacturer of light-gauge framing and finishing products,systems and services for commercial and residential construction. Dietrich offers the largest selection of light-gauge framing andfinishing products including drywall and structural framing, floor joists, roof trusses, metal lath, fire-rated assemblies, numerousdeflection systems and an extensive line of metal, vinyl, veneer, paper-faced, plaster and stucco beads and trims.
Dietrich Metal Framing companies and divisions include Dietrich Metal Framing Canada, Dietrich Design Group, Aegis Metal Framing,Vinyl Corp., and Accelerated Building Technologies. Together, we provide superior, cost-effective, single-source building and framing solutions.
Dietrich Metal Framing and Dietrich are trade names, trademarks and service marks of Dietrich Industries, Inc.
Miami
Baytown
Hutchins
Lenexa
Joliet
Hammond Warren
Lunenburg
Boonton
Baltimore
McDonough
Corporate Headquarters
200 Old Wilson Bridge Rd.
Columbus, OH 43085
800-873-2604
CLIP EXPRESS HUBS1.866.638.1908
DMF07_002-003:DMF07_002-003 6/30/10 3:21 PM Page 3
4
how to USEthis MANUAL
This catalog is designed to help you select the right products orsystems for your construction applications. It is the most compre-hensive manual in the industry. This catalog is divided intoten major sections that are color coded for easy reference.A comprehensive index is also located at the back of the catalogfor your convenience.
Each product page includes an extensive product overview, ben-efits, features and product and application renderings. Referencecharts contain size availability and packaging information.Each chart also includes metric sizing for your convenience.
Structural properties and load tables are available on our website www.dietrichmetalframing.com.
Product Codes/DesignatorsEach Dietrich product or system component is identified by a 3-or 4-digit alphanumericcode for ease of ordering. Corresponding SSMA member designator, where applicable, isalso provided for easy reference.
The Steel Stud Manufacturers Association (SSMA) has established industry standardnomenclature for steel framing members and components. The SSMA reference is identi-fied by an easy-to-understand alphanumeric code. The alpha designation is S, T, U, or F,where S = stud or joist, T = track, U = cold rolled channel, and F = furring channel.
Product identification is simplified with the SSMA standard member designation. While theletters define the section type, the numbers identify web depth, flange width and minimumsteel thickness as shown to the left.
Dietrich products meet or exceed all SSMA requirements. Care should be taken, however, when substituting materials in place of Dietrich Metal Framing.
There is a misconception within the construction industry regarding the substitution of one manufacturer’s products ormaterials for those of another manufacturer. The assumptionis that all studs of a given size and steel thickness are interchangeable. It may be possible that the substitution cansafely be made, but the decision should not be made untilthe structural properties of the products or materialsinvolved are compared by a qualified engineer.
Yield Strength, Fy/(psi or ksi)Yield strength is the property by which the strengthof steel is typically defined. Dietrich 20 and 18-gauge products are manufactured with steelhaving a yield point of 33 ksi. 16, 14 and 12-gauge products are manufactured with steelhaving a yield point of 50 ksi. Ksi is short for kipsper square inch. One kip is equal to 1,000 pounds.
Protective CoatingDietrich Metal Framing offers a variety of galvanized products that can be selected to meetthe specific requirements of a project.
Non- structural products have a corrosion resistantgalvanized coating that conforms to ASTM specification A1003 – G40 coating weight orequivalent corrosion protection. This coating is inaccordance with the industry standard coatingrequirements of ASTM C 645. These products canalso be ordered with enhanced coatings for specialapplications.
Structural Framing products are available with avariety of protective coatings. G60 zinc coatingsmeet the most widely applicable building codesand we are able to provide certified G60 productthat meets the G60 coating weight provisions ofASTM C 955. Certified G90 coatings are anenhanced option that can be requested for highlycorrosive environments. G60E coatings are an economical choice. G60E coatings for structuralproducts will pass the 100-hour salt spray testapplicable to "equivalent" coatings under ASTM A 1003, but cannot be certified by any supplier tomeet the G60 minimum coating standard underASTM C 955. The buyer is solely responsible toassure that products purchased properly satisfyany applicable code or specification.
Product LabelingSkids are clearly identified with master skid labelsthat display product, gauge, size, length, piececount, yield strength and any special skid mark-ings specified at the time of order. Individual ink jetlabeling (including company name, product, size,length, gauge, coating and yield strength) orembossing is also provided on many of our struc-tural framing members. UPC bar coding is alsoavailable for certain products.
Steel Thickness (Gauge)The steel thickness of a product or component isreferenced in terms of gauge or mils. The thickness or gauge is a key contributor to thestrength of the product.
400 S137-33Web Size: 400 = 4"Member Type: S = Stud or JoistFlange Width: 137 = 1-3/8" (1.37")Min. Steel Thickness in mils: 33 = .0329"
Web
Flange
WARNING: Handling of this productwithout the proper use of hand and eyeprotection may result in injury.
DMF07_004-005:DMF07_004-005 6/30/10 3:22 PM Page 4
5
ComprehensiveIndex
A comprehensive index can be found at theback of the catalog for a quick reference guideto our complete product and system offering,so you can easily locate the specific Dietrichproduct or system that meets your needs. Thisindex includes common names, synonyms andeven industry slang to help you quickly findexactly what you’re seeking.
Note: All products comply with ASTM thickness standards and Federal specifications shown in the Certificationof Materials in the back of this catalog. Minimum thickness is 95% of the design thickness per AISI code.
The trend today is to refer to steel thickness in terms of “mil” rather than “gauge”. This catalog includes bothfor ease of use. One mil is equivalent to 1/1000, (.001) of an inch. The mil thickness measures the uncoated base metal material. A 20-gauge stud measuring the minimum uncoated base metal at 0.030 inches is “30 mils thick”.
PatentsU.S. Patent Nos. 5,784,850; 6,021,618; 6,694,695;
5,689,922; 6,301,854; 6,691,478;6,418,694; 6,430,890, 6,688,069, and6,708,460 are owned by DietrichIndustries, Inc.
U.S. Patent Nos. 6,183,879 and 5,689,990 is owned byHadley Industries plc.
U.S. Patent No. RE 39,462 is owned by Sliptrack Sytems, Inc.
U.S. Patent Nos. 5,613,335 and 5,836,122 are owned byCorus CIC Inc.
U.S. Patent No. 5,836,133 is owned by B&D Industries, Inc.
TrademarksDietrich Metal Framing, and Dietrich are trade names, trademarksand/or service marks of Dietrich Industries, Inc.
TRADEREADY®, SPAZZER®, FAST CLIP™, EASYCLIP™, FAST TOP™,FAST STRUT™, UNI-CLIP™, RC DELUXE™, DOUBLETRACK™, THE BUCKET THAT MAY SAVE YOUR BUTT!™, ONE CALL CAN DO ITALLSM, THE PLACE TO STOP BEFORE THE BUILDING STARTSSM,SPAZZER and Design™, BEST VALUE and Design™, YOUR BESTVALUE™, DIETRICH CLIP EXPRESSSM, DIETRICH CLIP EXPRESS andDesignSM, BAR GUARD™, B-SERIES™, BP-SERIES™, C-SERIES™, CA-SERIES™, CS-SERIES™, CHN-SERIES™, DT-SERIES™, DTN-SERIES™, E-SERIES™, FC-SERIES™, M400-SERIES™, OT-SERIES™, QC-SERIES™, RC-SERIES™, S-SERIES™, TD-SERIES™, TR-SERIES™, TS-SERIES™, U-SERIES™, X-SERIES™, ZF-SERIES™, EVERYTHING YOU NEED, WHEN YOU NEED IT,HOW YOU NEED IT AND WHERE...YOU NEED ITSM, DOUBLE X™, E-DIETRICHSM, CORNERITE™, QUICKCLIP™, CORNERMASTER™, CWI™, CWN™, CSJ™, CSW™, CSE™, CSS™, “J” ROUND™,JUNIOR™, 103 DELUXE® and QUICKSILVER™ are owned by DietrichIndustries, Inc.
UltraSTEEL® is a trademark of Hadley Industries plc.
RIPBEAD™ and MINI-BEAD™ are trademarks of DietrichIncorporated.
ULTRA-SPAN® is a registered trademark of Aegis Metal FramingLLC
DANBACK® is a trademark of Daniel W. Tollenaar
GOLDLINE® is a registered trademark of Corus CIC Inc.
GRABBER® and GRABBER SUPERDRIVE® are registered trademarks of John Wagner Associates, Inc.
METALEX® is a registered trademark of Metalex Corporation
KEENE BUILDING PRODUCTS™ is a trademark of MetalexCorporation
LOX DRIVE® is a registered trademark of JJCT Enterprises, Inc.
SIMPSON™ and SIMPSON STRONG-TIE™ are trademarks ofSimpson Strong-Tie Company, Inc.
SLP-TRK® is a registered trademark of Sliptrack Systems, Inc.
UL® and UL Design® are trademarks of Underwriter'sLaboratories, Inc.
TAPCON® is a registered trademark of Illinois Tool Works, Inc.
© 2008 Dietrich Metal Framing. All rights reserved. Printed in U.S.A.
Standards & SpecificationsAll structural properties are developed in accordance withthe American Iron and Steel Institute’s “Specification forthe Design of Cold-Formed Steel Structural Members.”
Metric SpecificationsAt your request, Dietrich Metal Framing will provide“soft” metric conversions on its products and systems tohelp specifiers match metric design sizes. In addition,some products are available with hard metric dimen-sions from selected manufacturing facilities.
General NotesThe data contained in this brochure is intended tobe used as a general guideline only and does notreplace the judgments and designs of a qualifiedarchitect and/or engineer. This catalog does notprovide load data necessary for building design.Load capacities, limiting heights, physical and
structural properties and span data for Dietrichstructural framing can be found on our web site atwww.dietrichmetalframing.com.
Product, application renderings and photographsare provided as a tool to show the general intent ofthe framing or finishing application only. These renderings or photographs may or may not be applicable to a specific project. They do not replaceor supercede the architect or engineer of record,ASTM guidelines, national or local building codes orapproved industry standards.
Dietrich Metal Framing reserves the right to changeor modify the information contained in this catalogwithout prior notice or obligation. The information inthis catalog supercedes all previously publisheddata. Products and systems may be improvedand/or changed after this catalog is printed.
All products described here may not be available inall geographic markets. Consult your local salesoffice for information.
Thickness ASTM
Gauge Mils Design Thickness Minimum Thickness ColorInches mm Inches mm Code***
25 18 0.0188 0.478 0.0179 0.455 None20 DW 30 0.0312 0.792 0.0296 0.752 Pink20 STR 33 0.0346 0.879 0.0329 0.836 White
18 43 0.0451 1.146 0.0428 1.087 Yellow16 54 0.0566 1.438 0.0538 1.367 Green14 68 0.0713 1.811 0.0677 1.720 Orange12 97 0.1017 2.583 0.0966 2.454 Red
Steel Thickness with Color Code
*Not all products are available in all areas.**The term “Effective Thickness” was created by Underwriters Laboratory (UL) to establish a minimum thicknessmeasurement after the UltraSTEEL® manufacturing process has occurred. Effective thickness is the measurementacross the peaks of the dimples or the thickest part of the steel. The manufacturing, base steel and quality controlprocess is verified by independent third party UL representatives, who make regular unannounced visits to Dietrich’smanufacturing facilities to assure full compliance with UL established quality control standards.***Color coded product may or may not be available. Varies by market.
Thickness ASTM
Gauge Mils Effective Thickness** Minimum Thickness ColorInches mm Inches mm Code***
25EQ 15 0.034 0.86 0.015 0.38 None20DW EQ 25 0.055 1.34 0.025 0.63 Pink20STR EQ* 28 0.060 1.52 0.028 0.71 White
UltraSTEEL® Non-Structural Steel Thickness with Color Code
WarrantyOur products are manufactured in accordance with company standards and/or industry standards, as applicable. All DietrichMetal Framing products are covered by our standard warranty which is contained in our Standard Terms and Conditions of Saleand which will be provided upon request. Generally, we warrant our products will be free from defects in material and workmanship at the time of shipment, subject to the limitations stated in the warranty. Unless specifically agreed in writingby us with respect to specific orders, we do not make any warranty of merchantability or fitness for a particular purpose. Thebuyer is responsible to assure that buyer orders the appropriate product for any applicable code or specification requirements.
NOTICE: Our liability is expressly limited to replacement of defective products. We shall not be liable for incidental and consequential damages, nor for any loss caused by misuse or misapplication of our products. Any claim shall be deemedwaived unless made in writing to us within thirty (30) days from the date it was or reasonably should have been discovered.
DMF07_004-005:DMF07_004-005 6/30/10 3:22 PM Page 5
6
the “DIETRICH”difference
More products…more brands…and more value with fast,accurate and reliable service. It’s what you expect from aleader—it’s what you get from Dietrich.
Supplier ConsolidationStreamline the procurement process, reduceadministrative and supply costs and improveoperating efficiency.
Breadth of ProductsThe industry’s largest product offering of framingand finishing products, systems and services.
ServiceFast, reliable and consistent service whereand when you want it.
Quality“Zero” defects is our goal. You get the samehigh-quality, consistent, precision-formedproducts each and every time.
On-Time DeliveryWe deliver it when you want it.
Brand RecognitionThe most specified, requested and usedbrands in the industry.
EVERYTHING you need, when you need it,
DMF07_006-007:DMF07_006-007 6/30/10 3:23 PM Page 6
7
National DistributionMore than 40 manufacturing and service locations with facilities in most major metropolitan cities servicing North America. Dietrich is the acknowl-edged leader when it comes to supporting the supply requirements of large national and multi-national customers.
Technical SupportThe finest technical assistance in the world. We respond to over 30,000 calls per year.
Order AccuracyWe do everything we can to make sure each and every order is right the first time. We send immediate faxed order confirmations so you can also double-check the order.
High Fill RatesOur sophisticated manufacturing and loading processes ensure the highest fill rates.
New Product DevelopmentWe continually develop and introduce countless new products, systems and services to meet the expanding needs of the construction industry.
TrainingOur field representatives are recognized as experts in the industry. They provide comprehensive product, installation and sales training.
Market ExpansionWe commit substantial resources to grow the light-gauge market and create more opportunities for our customers in the supply chain.
You Get… What You Pay for
You can always find someone with a cheaperprice. But no one will offer a lower overall costand better value. We go far beyond supplyingproducts. No matter where you are in the sup-ply chain, Dietrich will streamline the design,procurement and building process whileimproving reliability, quality, productivity andyour bottom line.
how you need it and where…YOU NEED IT.SM
DMF07_006-007:DMF07_006-007 6/30/10 3:23 PM Page 7
8
the BENEFITSof STEEL
Superior and Uniform Quality
■ Steel is roll-formed into precise, uniform shapes with exactingtolerances for consistent material quality. There is no need forsorting (culling) or special handling to inspect for crown.
■ Steel studs are straight. They don’t warp, twist, bow, split or have knots, which meansstraight walls, square corners and doors and windows that open and close properly.
■ Steel is dimensionally stable and won’t shrink like wood, eliminating nail popping,wall cracking or floor squeaking.
■ Steel does not rot, promote mold or mildew and is impermeable to termites, verminand insects.
High Strength/Light Weight/Versatile■ Steel has one of the highest strength-to-weight ratios of any building material.
■ Because of its strength, steel can mean fewer framing members with wider on-center spacing, reducing material and labor costs.
■ Steel framing can weigh substantially less when compared to traditional buildingmaterials like masonry and concrete systems.
■ Light-gauge framing can reach spans far greater than traditional or engineeredlumber, providing larger open spaces, taller walls and flexible floor plans.
■ Steel framing lightens structures, reducing foundation requirements and oftenreducing or eliminating piling.
■ Stick for stick, steel can weigh up to 50% less compared to lumber.
■ Steel can adapt to almost any application and works well independently or in combination with other structural systems.
What about Rust?■ Steel framing members in wall cavities,
attic spaces or crawl spaces that are notexposed to water will last over 300years, per a study conducted in England.
■ Forensic studies recently conducted onOahu residences built over 40 years agoshowed steel wall studs with no visiblesigns of corrosion.
■ Zinc coating protects steel by providinga physical barrier as well as cathodicprotection to the underlying steel. Whenthe base is exposed, such as at a cut or scratch, the steel is cathodicallyprotected by the sacrificial corrosion ofthe zinc coating adjacent to the steel.
BUILD with
DMF07_008-009:DMF07_008-009 6/30/10 3:24 PM Page 8
9
What about Cost?
■ More economicalthan traditionalmasonry, concreteand otherconstructionmethods.
■ Reduces or eliminatescallback costs for nail pops, floorsqueaks and wall cracks due toshrinkage. The NAHB estimates theaverage callback costs the builder over$350.00 per call.
■ Lower costs for construction andhomeowner’s insurance.h STEEL today...
Fire Resistance■ Steel framing is non-combustible and
will not add fuel to a fire. It improvesfire safety in compliance with localcodes and regulations.
■ Steel framing offers code approvedincreases in allowable floor area and/orallowable building heights compared to conventional wood framing.
■ One-third of all fires start in the wall cavity.
■ Actual case studies show steel housesperform very well in house fires, withlittle or no damage to the framingstructure.
TermitesA few things you should know.■ Over $1 billion is spent each year for
prevention, control and repair.
■ Steel framing provides a termite-proofsolution for the structural integrity ofyour project.
■ The most ferocious termite is theFormosan Subterranean “SuperTermite.”
■ An average colony consists of about 3 million termites, but can be as largeas 10 million. A single colony normallysurvives about 35 years.
■ A well-fed Formosan queen can live for 25 years and lay 1,000 eggs a day.
Mold■ Steel does not promote the growth
of mold and reduces the threat of staggering litigation.
■ Mold requires an organic nutrientsource and moisture to grow andflourish. Steel is inorganic and does notcontain moisture like wood. Kiln driedlumber still has between 11–14%residual water content.
■ California has already passed mold-related laws, and nine other states havelegislation pending.
DMF07_008-009:DMF07_008-009 6/30/10 3:24 PM Page 9
10
the BENEFITSof STEEL
What about Lightning?■ Steel buildings are lightning resistant because steel framing provides
multiple conductive paths directly to the ground.
■ The steel frame reduces the likelihood of explosions, secondary fires or personal injury.
■ Steel skyscrapers have provided occupants with safe offices andresidences for years.
Earthquakes or Hurricanes?■ Steel framing can be engineered to meet the highest seismic and wind loads
prescribed by building codes.
■ Steel has the highest strength-to-weight ratio of any framing material; a lighterstructure with stronger connections results in lower damage from seismic force.
■ Steel’s strength and resiliency help it to survive earthquakes.
■ Smaller probability of damage in high winds; stronger connections (screwed vs. nailed) can withstand greater winds.
■ For generations we have relied on the strength and durability of steel in ourcommercial buildings, hospitals and schools.
...for benefits
DMF07_010-011:DMF07_010-011 6/30/10 4:23 PM Page 10
11
Easy to Use
■ Interior nonload-bearing studs are cuteasily with metal snips (aviator snips). Theydo not require the use of a circular saw.
■ Simply twist metal studs into place andscrew attach. Make a mistake and simplyreverse the screw gun.
■ Up to 50% lighter than wood.■ Pre-punched holes eliminate drilling for
electrical and plumbing lines.■ Special order cut-to-length material
eliminates field cutting and waste.
that will LAST A LIFETIME.
EnvironmentalBenefits■ Steel offers builders an environmentally
friendly alternative to wood.
■ There is little waste when using steelframing materials.
■ Builders can reduce their disposal costsand divert material from local landfills(2% – steel vs. 20% – lumber).
■ Building an average wood-frame homegenerates approximately 50 cubic feetof landfill waste, while a comparablesteel home generates about 1.5 cubicfeet of waste.
Live and Breathe Easier■ The Healthy House Institute
recommends steel framing for goodindoor air quality.
■ Chemically sensitive homeowners and those susceptible to asthma areexposed to fewer toxins in a steel-framed home.
■ The American Lung Associationencourages the use of steel framingwith its Health House program.
■ Steel resists mold spores that can leadto chronic illness.
■ No pesticides or toxins are required to protect the framing from termites or vermin.
■ No off gassing from resins, adhesives or chemicals normally used for woodconstruction.
■ Better insulation values with EPS foamreduces outside noise pollution.
North America’s MostRecycled Material■ Steel is 100% recyclable and
considered a green building material.
■ Steel framing materials contain on average 67% recycled steel.
■ Steel can be a significant contributor to the LEED certification process.
■ It takes 25 old growth trees to build a2,500 square foot home, compared with7 recycled automobiles for the samesteel-framed home.
■ 60 million tons of steel scrap arerecycled each year: more than paper,aluminum, glass and plastic combined.
DMF07_010-011:DMF07_010-011 6/30/10 4:23 PM Page 11
12
the BESTof BRANDS
the BRANDS you KNOW!the BRANDS you TRUST!the BRANDS the PROS DEMAND!
theBESTof
Quality is simply not compromised. That’s why Dietrich only pro-vides the best brands and the highest-quality products available.
We offer more than 3,000 high-quality framing and finishingproducts available to meet your every need.
DMF07_012-013:DMF07_012-013 6/30/10 3:27 PM Page 12
13
f COMPANIES
Aegis Metal Framing, through an internationalfabrication network, provides computer-designed, factory-built, light-gauge metaltruss, wall and floor panels for commercialstructures. . . . . . . . . . . . . . . . 314-851-2200
Accelerated Building Technologies (ABT)Ideal for all building types and exterior finishes,accel-E™ is a thermally efficient, high performance wall panel system combining steel’sstrength with the insulation of expanded polystyrene (EPS).. . . . . . . . . . . . 412-490-5037
Vinyl Corp., another best-in-class companyoffering one of the industry’s largest vinyl finish-ing product selections for drywall, stucco, EIFS,DEFS and ceiling applications. . . 800-648-4695
Dietrich Metal Framing, and Dietrich are tradenames, trademarks and service marks of DietrichIndustries, Inc.
Dietrich Design Group (DDG) is the largest light-gauge framing engineering company in thecountry. DDG is licensed in all 50 states and cansupply technical assistance, design assistanceand shop drawings for projects built anywhere inthe world. . . . . . . . . . . . . . . . . . . 800-873-2443
The Best ofCompanies
Combining the best of companies to offer a com-plete array of products, systems and services,this unique synergy of companies can providetotal and comprehensive support for every phaseof the construction process including design,supply, fabrication and installation.Discover how each of these Dietrich companiescan lower your cost and improve your productivity.Dietrich Metal Framing related companies anddivisions include Dietrich Metal Framing Canada,Aegis Metal Framing, Vinyl Corp., Dietrich DesignGroup and Accelerated Building Technologies.Together, they provide the expertise, systems andtechniques for superior, cost-effective, single-source, fast track framing, finishing and buildingsolutions.
DMF07_012-013:DMF07_012-013 6/30/10 3:27 PM Page 13
the BESTof SERVICES
theBESTof SDietrich Clip ExpressSM
If we get it today, you get it tomorrow. Dietrich Clip ExpressSM service offers various ship-ping options from standard ground to overnight express for the widest selection of deflec-tion, bridging, rigid, general purpose and specialty clips and fasteners. We understand thatin today’s fast track construction environment, keeping a project on schedule is critical.Count on us to get it where, when and how you want it.
On-Time DeliveryOn time, when you want it, where you want it. Dietrich’s primarily dedicated fleet of contract carriers set the standard for on-time delivery performance.
Technical SupportDDG, our independent professional services company, provides the finest technicalsupport services available for light-gauge framing. Licensed in all 50 states, DDG provides a wide array of services including certified shop drawings, free preliminarydesigns and a technical support hotline for immediate assistance.
Customer CareOur people work harder so you don’t have to. You will find the most knowledgeable,responsive “can do” attitudes in the industry. At Dietrich Metal Framing, customer serviceis simply not a department…it’s a contagious attitude.
Field SupportWell-trained, knowledgeable andexperienced field personnel areexperts in the industry. They provideproduct support, in-depth training,new product demonstrations andinstallation assistance.
Need It Fast?Look for the Dietrich Clip ExpressSM iconthroughout this catalog. These prod-ucts are readily available for same-dayshipment.
OvernightDelivery!
Available for
14
DMF07_014-015:DMF07_014-015 6/30/10 3:28 PM Page 14
15
f SYSTEMS
The Best ofSystems
It’s not simply about supplying high-qualityproducts. It’s about value-added systems andassemblies that reduce building cost andimprove building quality. Building with Dietrichhigh-performance systems means…superiorquality, faster installation, system flexibilityand increased productivity.
TradeReady®
Floor SystemA lightweight, cost-effective alternative to openweb truss, bar joist, engineered lumber, cast-in-place or hollow-core floor assemblies.
Area Separation WallA two-hour fire-rated system provides protec-tion between adjacent living units in apartmentbuildings, condominiums, townhouses andmulti-family construction.
CT Cavity Shaft WallNonload-bearing fire-rated wall assembliesthat provide critical, life safety, fire-resistantprotection for elevator shafts, stairwells, verticalchases and mechanical enclosures.
Ultra-Span*
The safest, most cost-effective, noncom-bustible, fully engineered, prefabricated UL*** classified light-gauge roof truss system.
*Ultra-Span is a registered trademark of Aegis Metal Framing LLC.**SLP-TRK is a registered trademark of Sliptrack Systems, Inc.***UL™ and UL Classified are trademarks of Underwriter’s Laboratories, Inc.
SLP-TRK**
Sliptrack systems provide over 100 UL*** rateddeflection and fire-rated assemblies for head-of-wall framing.
DMF07_014-015:DMF07_014-015 6/30/10 3:28 PM Page 15
16
one CALLcan do it ALLSM
ShippingNeed it fast — we ship 95% of in-stock orderswithin 48 hours.
OrderingPhone, fax, e-mail or EDI — you decide.
ServiceFar more than order takers, Dietrich CustomerCare Representatives are experts in the industry.Let us put our knowledge to work for you.
SupportHave questions? We have the answers. Call, faxor e-mail us and we will answer your questionspromptly.
ProductsOver 3,000 different products/product combina-tions. The largest selection of products in theindustry. One call that truly does it all.
CustomWhen “off-the-shelf” just won’t do, call Dietrich.We can custom fabricate and provide made-to-order products to meet your needs.
E-BusinessWe make it easy for you to do business. Fast,flexible options to make you more efficient,reduce procurement and administrative costsand improve productivity.
■ EDI — Electronic Data Interchange
■ Flexible invoicing by mail, fax, e-mail or EDI
■ Easy payment options by check, wiretransfer or credit card
Dietrich is committed to ongoing developmentof technologies and e-business solutions tolower procurement costs.
DMF07_016-017:DMF07_016-017 6/30/10 3:29 PM Page 16
17
CUSTOMER careConvenient OrderingWith just one call, you can reach the expert sales and support team for prices, availability, ordering, technical support or additional information on our over 3,000 products.
At Dietrich, our Customer Care Representatives are ready to help you with all your needs. Ourskilled, knowledgeable staff utilizes a sophisticated order entry system to ensure customer ordersand inquiries are handled quickly and accurately.
We Get It Right the First TimeThe order you placed on Monday with another company arrives on Thursday and you find out it’swrong. What a mess. Now you have to deal with that very upset contractor waiting for the materi-al, not to mention all the paperwork, phone calls and hassles that go along with a wrong order.Maybe next time you’ll turn to Dietrich. We get it right the first time.
Starting with the order process, our Customer Care Representatives double and triple check eachand every order. Next, we send you a faxed confirmation to verify the correct size, gauge, length,piece count and price.
Using state-of-the-art manufacturing technologies and automated production control, your order ismanufactured to exact specifications. Every step of the way numerous quality control checks aremade to ensure the highest product quality and integrity. When your order is completed and readyfor transit, each unit is automatically reconciled against the pick list using detailed bar code tracking. The truck cannot be released until the order completely reconciles. It’s no wonder Dietrichhas one of the best fill-rates in the business.
“Can Do” AttitudeIf there is a way, we go the extra mile to find it and do it. We know the success of your business depends on our ability to get it when you want it, how you want it and where you want it.No one works harder to exceed your expectations.
Your Business Is Built on ServiceThat’s why our Customer Care Representatives are dedicated to immediate and quick response. If we can’t answer your inquiry immediately, we will within 60 minutes. It’s our commitment to you.
CustomerCare
It’s all about taking care of you. We get it. Weunderstand that you are the lifeblood of ourbusiness. Our world revolves around you.That’s why we do everything in our power to make sure you experience world-class customer care each and every time.
DMF07_016-017:DMF07_016-017 6/30/10 3:29 PM Page 17
18
AEC support
and SERVICESDietrich offers unparalleled support, training, education andproject assistance to design, engineering and building profes-sionals. We have the products, systems, services and compa-nies that can help you drive cost out of the building process.
Architects and Specifiers■ CEU On-Site and On-Line Learning
■ Technical Assistance
■ LEED* Accredited Professionals
■ On-Line Specifications, Certifications and Code-Body Approval Reports
■ Integrated Light Gage Framing Systems
■ National and World-Wide Availability
■ Design/Build Support and Assistance
■ Extensive Light Gage CAD Library
■ Prefabricated and Turnkey Light Gage Building Systems
Engineering and Design Professionals■ Broadest Product Selection for Cost Effective Design and Building
■ Boxed-Lunch Learning Sessions
■ Certified/Sealed Shop Drawing in all 50 States
■ Extensive Light Gauge CAD Library
■ Design Build Assistance
■ Advanced Light Gage FramingTechnologies
Contractors andBuilders■ On-Site Product Demonstrations
■ Certified/Sealed Shop Drawing in all 50 States and Canada
■ Technical Support
■ On-Line Submittal Builder
■ Products and Services that Reduce Costs and Improve Productivity
HOPSON SPECIALTY SYSTEMS
DRYWALL CONSTRUCTION
ACOUSTICAL CEILINGS • LATHING AND PLASTERING • SPRAYED FIREPROOFING • DEMOUNTABLE PARTITIONS
SOUND CONTROL • EXTERIOR INSULATION FINISH SYSTEMS • INSULATION
RELATED MATERIALS
February 5, 2004
Re: A deserved testimonial
Dietrich Design Group
1414 Field Street
Building C
Suite 1
Hammond, Indiana 46320
Attention: Mr Michael C. Kerner, Manager of Technical Services
Dear Mike,
Our relationship spans many years…this is our twenty-fifth year…and throughout our history, we can say with all
candor that Dietrich Design Group has been a silent partner in aiding us to attain a strong presence in the cold-
formed metal framing sector of the market which we serve. We have said in the past and continue to believe that
our destiny, indeed Dietrich Industries, Inc.’s destiny too, rests squarely on the shoulders of Dietrich Design
Group, since metal framing continues to be the product of choice in the commercial construction market and con-
tinues to develop a presence in the light commercial as well as the residential sector.
Dietrich Design Group elevates metal framing from being just another commodity item essential entity status
through its well-staffed, well-educated, dedicated and committed engineering group, where the byword is the epito-
f ssionalism. More often than not, one speaks with a REAL person…and for those few occasions where
essary, human follow-up ALWAYS occurs.
i al support quite dramatically; it is rare that a week passes whereby we
embers of your staff. We have NEVER had a negative expe-
DMF07_018-019:DMF07_018-019 6/30/10 3:30 PM Page 18
19
TECHNICAL assistance & SUPPORTSpecialized Services for
Specialized Needs
FREE Preliminary DesignDietrich Design Group provides unparalleled customer support through our free preliminary designservice. Customers can e-mail or fax building cross-sections, or can express mail full-size projectplans and specifications. This valuable design service provides the critical information that can helpcustomers during the bidding process.
FREE Technical Support HotlineWe respond to more than 30,000 calls each year through our Technical Support Hotline. This uniqueand value-added service provides immediate response to engineers, architects, contractors andbuilders, ranging from general questions to detailed specification interpretations.
Certified Shop DrawingsThrough our in-house engineering staff,Dietrich Design Group provides certified shopdrawings and calculations. This service providesour customers with the most detailed, easy-to-use drawings, and the most cost-effectiveframing solutions in the industry. From multi-story load-bearing structures to curtainwallconstruction, no matter how big or small thejob, DDG is there to help. Our lead-times andfees are among the best available.
The “Dietrich”AdvantageDietrich Metal Framing is the industry leader insteel-framing products for the residential andcommercial markets. Dietrich Design Groupsupports these products through engineeringand technical expertise and superior customerservice. Together, customers have a one-stopresource for completing projects on time andwithin budget—all backed by safe, reliableand trusted products and technical expertise.
Technical Assistanceand Support
Dietrich Design Group (DDG) is the largestlight-gage framing engineering company inthe country. DDG is licensed in all 50 statesand Canada, and can supply technical assis-tance, design assistance and shop drawingsfor projects built anywhere in the world.
For fast, prompt assistance call, fax or mail your questions or design needs to the appropriate DDG location.
Dietrich Design Group (North) ■
1414 Field Street, Building C, Suite 1Hammond, IN 46320800-873-2443 or 219-853-9474 phone219-932-4141 fax
Dietrich Design Group (West) ■
2262 Rutherford Road,Suite 104Carlsbad, CA 92008800-873-2443 or 760-931-0465 phone760-931-9824 fax
Dietrich Design Group (South) ■
330 Greenwood PlaceMcDonough, GA 30253800-873-2443 or 678-304-5525 phone678-304-5556 fax
DMF07_018-019:DMF07_018-019 6/30/10 3:30 PM Page 19
20
INTERNATIONALDietrich Metal Framing specializes in providing products andservices on a global basis. Our highly talented and well-trained multilingual staff makes doing business a simple andeasy process. We can arrange and coordinate the entireprocess through one of our many established distributorsaround the world.
From the start, you will know you have chosen the right company. Our international grouplocated in Miami, Florida will help you every step of the way. They will begin by makingsure we are providing the exact product specifications to meet your needs. They willprovide product specifications in both metric and standard measurements. Ourspecialists will analyze “best cost” methods based on numerous portpossibilities due to our extensive plant locations. We can and will assistwith arranging a freight-forwarder and also provide either flat-rack orclosed-container loading at our facilities. By offering our customersthese loading options, we can substantially reduce extra loadingcosts and eliminate damage due to excessive handling.
In addition to supplying world-class products, we providethe world-class engineering and technical assistance tosupport light-gauge steel framing. Dietrich DesignGroup provides the architect, contractor or developerwith preliminary member sizing, technicalrecommendation, or certified shop drawings.
Our years of expertise afford us with theknowledge and know-how to provide you withthe most economical solution and source tomeet your needs. Our extensive internationalresume is a proud testament to the manyconstruction projects we have suppliedthroughout the world. If you’re looking for aninternational supply partner, look no further.Look to Dietrich Metal Framing.
DMF07_020:DMF07_020 6/30/10 3:32 PM Page 20
Interior (Drywall) DeflectionTrack SystemsDeflection Track Systems............40SLP-TRK® Slotted Track (BDTK) ..............................................42Long Leg (Deflection) Track (TR-Series™) with Spazzer®
9200 Bar (SPZD)..........................43Long Leg (Deflection) Track (TR-Series™) with U-Channel(CHN-Series™), EasyClip™ ClipAngles (U-Series™) and Screws ......................................44DoubleTrack™ (Overtrack) System(OT-Series™/TR-Series™) ..............45
Interior (Drywall) Nonload-Bearing UltraSTEEL® FramingBenefits of UltraSTEEL® ......24–25UltraSTEEL® Framing ............26–35UltraSTEEL® Fire & SoundAssemblies ..............................36–37Interior (Drywall) Nonload-Bearing Contour Track®
Contour Track®........................38–39
Interior (Drywall) Framing Products forBridging/BracingBridging Options ............................41Spazzer® 9200 Bridging andSpacing Bar (SPZD)......................46U-Channel (CHN-Series™) and EasyClip™ Clip Angles (U-Series™) ......................................47Interior (Drywall) Framing Products for Ceiling ApplicationsFurring Channel (FC-Series™) U-Channel (CHN-Series™) HangerWire/Tie Wire and Furring ChannelClips (MFCC) ..........................48–49Interior (Drywall) FramingProducts for Various DrywallFraming AssembliesCorner Angle (CA-Series™)Hemmed Corner Angle (HCN)and 120˚/135˚ (CAEW)..............50Furring Channel (FC-Series™) forWalls and Ceilings ........................51Resilient Channels (RC-Series™)for Walls and Ceilings ..........52–53Danback® Wood Backing Plate ..........................54–55Z-Furring (ZF-Series™) ..................56Backing Plate (BP) ........................57Grommets (GROM) ....................58
21
DMF07_021:DMF07_021 7/2/10 9:41 AM Page 21
Interior (Drywall) Nonload-Bearing,Nonstructural Framing
Dietrich Metal Framing’s nonload-bearing, nonstructural or interior framing metal studsand tracks are C-shaped channels, roll-formedfrom corrosion resistant, galvanized steel. Thesechannels are assembled to provide efficient, lowcost framing for partition walls, ceilings and column fireproofing. Gypsum wallboard, veneer
plaster or traditional lath and plaster is applied to the metal framing to complete thewall assembly. These assemblies are nonload-bearing, nonstructural wall systems thatsupport gypsum panel construction. They are not designed to carry an axial load.Most nonload-bearing, nonstructural walls are constructed using 25 gauge equivalent(15 mils) UltraSTEEL® (0.034" effective thickness), 20 DW gauge equivalent (25 mils)UltraSTEEL® (0.055" effective thickness) or 20 STR* gauge equivalent (28 mils)UltraSTEEL® (0.060" effective thickness) stud and track.
* Available in limited markets
All of Dietrich’s interior, nonload-bearing stud and track products are manufacturedutilizing a next-generation manufacturing technology called UltraSTEEL® framing.UltraSTEEL® technology is a manufacturing process that alters the characteristics offlat base strip steel, providing higher strength capacity from lighter gauge material.The process effectively work-hardens the steel with two mating rolls. During theprocess, the effective thickness of the material is increased to that of the originalthickness, plus the depth of the ribbing. This process, in effect, dimples the entirestud or track member. UltraSTEEL® technology significantly increases the productperformance when compared to traditional interior metal stud framing. Some of thebenefits include better acoustical performance, improved fire resistance, faster andeasier installation, improved safety and better finish quality.
INTERIORFRAMINGOVERVIEW
Dietrich Metal Framing interiorframing products are used in a variety of interior, nonload-bearingconstruction applications. The mostcommon uses of nonload-bearingor nonstructural metal framing arepartition walls, ceilings and columnfireproofing in low-rise, mid-rise,high-rise, educational, institutionaland multi-use commercial struc-tures. Nonload-bearing framing isalso used in residential applicationsincluding partition framing andbasement finishing. Metal framing isrequired in most commercial struc-tures because it is noncombustibleand does not add fuel to the fire.Interior framing components aremanufactured from corrosion resistant galvanized steel that offerssignificant protection from the elements. In addition these framingmembers are precision manufac-tured to exacting tolerances thatprovide the framework for superiorconstruction.
Dietrich Metal Framing offers anextensive selection of interior framing products including studsand tracks, furring and resilientchannels, deflection products, corner angles and backing plates.
Inte
rior
Fram
ing
Ove
rvie
w
22 The place to stop…before the building starts! SMrequest a quote online @
DMF07_022-023:DMF07_022-023 7/2/10 9:44 AM Page 22
Dietrich UltraSTEEL® Metal Track (or runner) is available incorresponding sizes and is offered in a variety of legheights including 1-1/4", 2" and 3" legs. The 1-1/4" legtrack is the industry standard. Track is used to align andsecure studs to floors and ceilings, and is also used in conjunction with studs for constructing openings, headersand sills. Metal studs are twisted into top and bottom trackand typically screw attached using 7/16" pan head framingscrews.
Like most products, drywall studs and track can be purchased in stock lengths, or custom orderedto match specific job requirements. This flexibility allows the end user to more efficiently controllabor costs at the jobsite.
Dietrich UltraSTEEL® Metal Studs are available in 1-5/8", 2-1/2", 3-1/2"*, 3-5/8", 4", 5-1/2"* and 6" widths or webdepths. Studs are manufactured using the UltraSTEEL®
process. Studs may be spaced at 12", 16" or 24" on-centerbased on wall height. Wall height, stud spacing, framingcondition, deflection limitations and lateral load are all fac-tors that must be considered in determining the correctsize and gauge of the applicable product.
* Available in limited markets
See. Feel. Hear.EXPERIENCE
■ Superior Product Enhancement
■ Better Acoustical Performance
■ Improved Fire Resistance
■ Faster, Easier and Safer
■ UL® Classified in Design V450
■ Stronger Load-Carrying Capacity
■ Greater Limiting Heights
■ Stiffer, More Rigid Construction
■ Easily Identifiable Pattern
OverviewInterior Fram
ing Overview
23For more information or to contact a sales representative, see page 3
DMF07_022-023:DMF07_022-023 7/2/10 9:44 AM Page 23
Inte
rior
(Dry
wal
l) N
onlo
ad-B
earin
g U
ltraS
TEEL
®Fr
amin
g
24 The place to stop…before the building starts! SMrequest a quote online @
Enhances Screw Retention■ Independent tests have shown improved screw retention characteristics■ The dimpled surface reduces screw “spin out”
Dietrich UltraSTEEL® Framing is made from 40 KSI steel combined with double helixwork hardening process which increases strength of screw retention. The DietrichUltraSTEEL® Framing cross-section ensures every screw is in contact with a materialthickness greater than the nominal gauge of the steel. Furthermore, the location ofscrews within Dietrich UltraSTEEL® Framing material creates inward pressure aroundthe point of contact as a pull-out force is applied.
0 112 225 337 450 562 787675
Screw Pull-Out Force (lbs.)
Relative Screw Retention Graph
Traditional Metal Framing Dietrich UltraSTEEL® Framing
698 lbs.
630 lbs.
Screw Contact with DietrichUltraSTEEL® Framing
Nominal SteelGauge
The Dietrich UltraSTEEL® Framing cross-section ensuresthat every screw is in contact with a material thicknessmuch greater than traditional material thickness.
The location of screws within Dietrich UltraSTEEL®
Framing material creates inward pressure aroundthe point of contact as a pull-out force is applied.
Dietrich UltraSTEEL® Framing Traditional Metal Framing
FASTER... EASIER... and SAFERInstallation!
■ Improved productivity and quality
■ Virtually no screw riding
■ Tighter stud to track friction fitting
■ Sight line on flanges for more precise joints
■ Improved safety by reducing sharp edges and lips
BENEFITS of
DMF07_024-025:DMF07_024-025 7/2/10 9:49 AM Page 24
Benefits of UltraSTEEL®Interior (D
rywall) N
onload-Bearing UltraSTEEL
®Fram
ing
25For more information or to contact a sales representative, see page 3
Use and Hear Less!
That’s right, improved acoustical benefits.
The dimpled surface of the section has been shown to reducethe levels of noise transmission through walls and ceilings.Several sound insulation tests were conducted with variousgypsum boards.
Improved Fire Test Performance
Fire tests have shown an increase in performance with products produced from Dietrich UltraSTEEL® Framing.
70
60
50
40
30
20
10
0
3-5/8" Stud5/8" Gypsum Wallboard
3-5/8" Stud5/8" Gypsum Wallboard
Fiberglass Insulation
3-5/8" Stud5/8" Gypsum Wallboard
Fiberglass InsulationRC1 Channel
3-5/8" Stud5/8" Gypsum Wallboard
(double layer)Fiberglass Insulation
RC1 Channel
* A difference of 5 points reduces sound transmission by 50%
Acoustic Performance Graph
STC Rating Traditional Metal Framing STC Rating Dietrich UltraSTEEL® Framing
3938
48475252
61*56
120
100
80
60
40
20
0
Load Resistance Burn Through Temperature Transfer
Fire Test Performance Graph
Test Parameter
Traditional Metal Framing Dietrich UltraSTEEL® Framing
108
79
105
7989
69
Min
utes
making our industry BETTER! SM
DMF07_024-025:DMF07_024-025 7/2/10 9:49 AM Page 25
Inte
rior
(Dry
wal
l) N
onlo
ad-B
earin
g U
ltraS
TEEL
®Fr
amin
g
26 The place to stop…before the building starts! SMrequest a quote online @
Drywall Stud
Drywall Nonload-Bearing (Nonstructural) Studs (UST-Series™)Featuring UltraSTEEL® Framing Technology
Drywall UltraSTEEL® (nonload-bearing)interior studs are used in nonload-bearing(nonstructural) interior wall systems orpartitions that support gypsum wallboardconstruction. Drywall metal studs areavailable in 25 Gauge EQ (equivalent), 20 DW Gauge EQ (equivalent) and 20 STR Gauge EQ (equivalent) thickness*and are manufactured utilizingUltraSTEEL® framing technology. In orderto determine the proper gauge, wallheight, stud spacing, deflection limitationsand lateral loading must all be considered.Studs are available in a variety of web sizes and can be ordered in stock and custom lengths. Metal studs are twisted into the top andbottom track and either friction fit, crimped or screw attached at 12", 16" or 24" on center spacing.
In contrast to wood studs, metal studs will not warp, twist or bow resulting in straighter walls free from cracks and nail pops. Metalstuds are impervious to insects, mold and rot. They are noncombustible and will not add fuel to a fire.
■ Roll-formed from corrosion-resistant galvanized steel thatconforms to ASTM C 645
■ Pre-punched knockouts for easy installation of electrical,plumbing and bridging
■ Available sizes: 1-5/8", 2-1/2", 3-1/2"*, 3-5/8", 4", 5-1/2"* and 6"■ Available gauges: 25 EQ, 20 DW EQ and 20 STR EQ*
EQ = equivalent to traditional stud gauges
* Available in limited markets
UltraSTEEL® Drywall Nonload-Bearing (Nonstructural) Studs (UST-Series™)DMF Base Metal Effective Metal Size Weight Packaging
Product Member Gauge Thickness Thickness* Inches mm lbs/ft kg/m Pcs/ Pcs/Code Designation Equilivent (Inches) (Inches) Bundle Skid
162 USTN 0.015 0.034 1-5/8 41.3 0.239 0.355 480250 USTN 0.015 0.034 2-1/2 63.5 0.286 0.425 480
USTN 362 USTN 25 EQ 0.015 0.034 3-5/8 92.1 0.347 0.516 10 360400 USTN 0.015 0.034 4 101.6 0.367 0.546 360600 USTN 0.015 0.034 6 152.4 0.474 0.705 180162 USTE 0.025 0.055 1-5/8 41.3 0.390 0.580 480250 USTE 0.025 0.055 2-1/2 63.5 0.469 0.698 480
USTE 362 USTE 20 DW EQ 0.025 0.055 3-5/8 92.1 0.569 0.847 10 360400 USTE 0.025 0.055 4 101.6 0.603 0.897 360600 USTE 0.025 0.055 6 152.4 0.782 1.163 180162 USTX 0.028 0.060 1-5/8 41.3 0.436 0.648 480250 USTX 0.028 0.060 2-1/2 63.5 0.524 0.779 480
USTX 362 USTX 20 STR EQ 0.028 0.060 3-5/8 92.1 0.637 0.947 10 360400 USTX 0.028 0.060 4 101.6 0.674 1.002 360600 USTX 0.028 0.060 6 152.4 0.875 1.300 180
*The term “Effective Thickness” was created by Underwriters Laboratory (UL) to establish a minimum thickness measurement after the UltraSTEEL® manufacturing processhas occurred. Effective thickness is the measurement across the peaks of the dimples or the thickest part of the steel. The manufacturing, base steel and quality controlprocess is verified by independent third party UL representatives, who make regular unannounced visits to Dietrich’s manufacturing facilities to assure full compliance withUL established quality control standards.
DMF07_026-027:DMF07_026-027 7/2/10 9:51 AM Page 26
UltraSTEEL® FramingInterior (D
rywall) N
onload-Bearing UltraSTEEL
®Fram
ing
27For more information or to contact a sales representative, see page 3
Drywall Knockouts Conveniently placed holes for easy installation of wiring,plumbing and bridging■ Pre-punched at regular intervals
■ Designed to accept the installation of standard grommets
■ Custom hole placement available on request
3/4" wideknockout in 1-5/8" and 2-1/2" studs
West CoastPunch Pattern East and Central
Punch Pattern
Varies
4'
4'
1'
2'
2'
2'
2'
Varies
Dietrich UltraSTEEL® studs for interiornonload-bearing, nonstructural framingare pre-punched with knockouts atregular intervals. These punch-outs arespecifically designed to allow for therapid installation of pipes, electricalconduit, wiring and bridging.
CAUTION: Care must be taken during installation to ensureconsistent alignment of knockouts. Conduit, grommets,hangers or insulators must be used to keep mechanicalpiping and electrical wires from direct contact with the steel.
1-1/2" wide knockout in 3-5/8"and wider studs
DMF07_026-027:DMF07_026-027 7/2/10 9:51 AM Page 27
Ultr
aSTE
EL®
Phys
ical
, Stru
ctur
al &
Com
posi
te L
imiti
ng H
eigh
t Inf
orm
atio
n
28 The place to stop…before the building starts! SM
25
20
15
10
5
0
25-Gauge EQ Dietrich UltraSTEEL® Framing with 1 layer 1/2" thick gypsum wallboard Compared to Traditional SSMA 362S125-18
SSMA Traditional Metal Framing Dietrich UltraSTEEL® Framing
12 16 24 12 16 24 12 16 24 12 16 24 12 16 24 12 16 24 12 16 24 12 16 24 12 16 24
Feet
1 Composite limiting heights based on single layer 1/2" thick gypsum board full height on each side with screws spaced 12" O.C. to framing members per ASTM C 754. Tested to ICC acceptance criteria AC86
L/360 L/240 L/120 L/360 L/240 L/120L/360 L/240 L/120
5 PSF 7.5 PSF 10 PSF
PatentsProducts manufacturedusing the UltraSTEEL®
process are protected bygranted USA Patents (Nos.6,183,879 and 5,689,990)and granted CanadianPatent (No.2,149,914/1993) togetherwith design registration.
UltraSTEEL® is aTrademark of HadleyIndustries plc.
Stud MemberSpacing 5 psf 7.5 psf 10 psf 15 psf
(in.) L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/36012 12'-6" 9'-11" 8'-8" 10'-11" 8'-8" — 9'-11" 7"-11" — 8'-8" — —
162 USTN 16 11'-4" 9'-0" 7'-11" 9'-11" 7'11" — 9'-0" — — — — —24 9'-11" 7'-11" — 8'-8" — — 7'-11" — — — — —12 15'-8" 12'-5" 10'-10" 13'-8" 10'-10" 9'-6" 12'-4" f 9'-11" 8'-8" 10'-1" f 8'-8" —
250 USTN 16 14'-2" 11'-3" 9'-10" 12'-5" 9'-10" 8'-7" 11'-3" 8'-11" 7'-10" 8'-11" s 7'-10" —24 12'-4" 9'-10" 8'-7" 10'-9" 8'-7" — 9'-9" f 7'-9" — — — —12 20'-10" 16'-7" 14'-3" 18'-3" 14'-3" 12'-3" 16'-3" f 12'-10" 11'-0" 12'-10" f 11'-0" 9'-6"
362 USTN 16 19'-1" 15'-1" 12'-10" 16'-5" f 12'-10" 11'-0" 13'-11" f 11'-6" 9'-11" 11'-0" f 9'-11" 8'-6"24 16'-6" f 12'-11" 11'-0" 13'-1" f 11'-0" 9'-5" 11'-2" f 9'-11" 8'-6" 8'-10" 8'-6" —12 22'5" 17'-9" 15'-6" 19'-7" 15'-6" 13'-2" 17'-0" f 13'-10" 11'-9" 13'-4" s 11'-9" 10'-1"
400 USTN 16 20'-6" 16'-3" 13'-10" 17'-0" f 13'-10" 11'-9" 14'-6" 12'-4" 10'-6" 11'-1" s 10'-6" 9'-0"24 17'-1" f 13'-11" 11'-9" 13'-8" f 11'-9" 10'-10" 11'-7" f 10'-6" 9'-0" 8'-11" s 8'-11" s —12 29'-10" 23'-8" 20'-9" 24'-7" f 20'-9" 18'-1" 20'-9" s 18'-10" 16'-5" 13'-10" s 13'-10" s 13'-10" s
600 USTN 16 25'-7" f 21'-6" 18'-9" 20'-11" f 18'-9" 16'-5" 17'-1" s 17'-1" s 14'-8" 11'-5" s 11'-5" s 11'-5" s24 20'-6" f 18'-9" 16'-5" 16'-9" 16'-5" 13'-10" 13'-5" s 13'-5" s 12'-3" 9'-0" s 9'-0" s 9'-0" s
f: Flexural stress controls allowable wall height s: Shear/web crippling control allowable wall height Minimum yield strength = 40 ksi
Dietrich UltraSTEEL® Framing’s 25-Gauge EQ Composite Limiting Heights (1 layer 1/2" thick gypsum wallboard)1
Dietrich UltraSTEEL® Framing’s 25-Gauge EQ Physical and Structural Properties
Notes: Section properties are determined in accordance with AISI-NASPEC 2001.Section properties are conservatively calculated using the thickness and yield strength of the base material, prior to the Dietrich UltraSTEEL® forming process.Calculated effective moment of inertia (Ixe) is based on serviceability determination.Effective section properties and moment capacity did not incorporate stress increase as a result of cold work of forming.* Depth over thickness ratio (h/t) is greater than 300.Yield Strength = 40 ksi
Base Effective Gross Section Properties Effective Section Allowable Torsional Section PropertiesMember Metal Metal Weight Properties Moment
Designation Thickness Thickness Area Ix rx Iy ry Ixe Sxe Ma Xo J Cw Ro Beta(inches) (inches) (lbs/ft) (in2) (in4) (in) (in4) (in) (in4) (in3) (in-lbs) (in) (10-5 in4) (in6) (in) (degree)
162 USTN 0.015 0.034 0.237 0.070 0.033 0.689 0.015 0.460 0.029 0.024 578 -1.062 0.580 0.009 1.347 0.378
250 USTN 0.015 0.034 0.284 0.084 0.087 1.020 0.017 0.452 0.078 0.045 1,087 -0.935 0.694 0.021 1.456 0.587
362 USTN 0.015 0.034 0.345 0.101 0.204 1.418 0.019 0.435 0.189 0.057 1,363 -0.815 0.842 0.049 1.693 0.768
400 USTN 0.015 0.034 0.365 0.107 0.256 1.546 0.020 0.429 0.233 0.063 1,509 -0.783 0.891 0.061 1.785 0.808
600 USTN* 0.015 0.034 0.472 0.139 0.675 2.205 0.022 0.396 0.535 0.108 2,580 -0.648 1.154 0.153 2.332 0.923
request a quote online @
DMF07_028-029:DMF07_028-029 7/2/10 9:53 AM Page 28
UltraSTEEL® FramingU
ltraSTEEL®
Physical, Structural & Com
posite Limiting H
eight Information
29For more information or to contact a sales representative, see page 3
Stud MemberSpacing 5 psf 7.5 psf 10 psf 15 psf
(in.) L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/36012 13' 2'' 10' 6'' 9' 2'' 11' 6'' 9' 2'' — 10' 6'' 8' 5'' — 8' 8'' — —
162 USTN 16 12' 2'' 9' 8'' 8' 5'' 10' 8'' 8' 5'' — 9' 8'' — — — — —24 10' 9'' 8' 6'' — 9' 4'' — — 8' 6'' — — — — —12 16' 0'' 13' 1'' 11' 5'' 14' 3'' 11' 5'' 9' 11'' 12' 4'' 10' 5'' 8' 10'' 10' 1'' 8' 10'' —
250 USTN 16 14' 11'' 11' 10'' 10' 4'' 13' 1'' 10' 4'' 9' 1'' 11' 4'' 9' 5'' 8' 3'' 8' 11'' 8' 3'' —24 13' 0'' 10' 4'' 8' 11'' 11' 3'' 8' 11'' — 9' 9'' 7' 11'' — — — —12 21' 4'' 17' 1'' 14' 7'' 18' 8'' 14' 7'' 12' 5'' 16' 3'' 13' 0'' 11' 1'' 12' 10'' 11' 1'' 9' 6''
362 USTN 16 19' 5'' 15' 4'' 13' 1'' 16' 6'' 13' 1'' 11' 2'' 13' 11'' 11' 9'' 10' 1'' 11' 0'' 10' 1'' 8' 8''24 16' 8'' 13' 2'' 11' 2'' 13' 1'' 11' 2'' 9' 6'' 11' 2'' 10' 0'' 8' 6'' 8' 10'' 8' 6'' —12 23' 1'' 18' 4'' 15' 11'' 19' 7'' 15' 11'' 13' 7'' 17' 0'' 14' 2'' 12' 1'' 13' 4'' 12' 1'' 10' 3''
400 USTN 16 20' 10'' 16' 8'' 14' 3'' 17' 0'' 14' 3'' 12' 1'' 14' 6'' 12' 8'' 10' 10'' 11' 1'' 10' 10'' 9' 3''24 17' 1'' 14' 4'' 12' 2'' 13' 8'' 12' 2'' 10' 2'' 11' 7'' 10' 9'' 9' 1'' 8' 11'' 8' 11'' —12 30' 1'' 23' 11'' 20' 10'' 24' 7'' 20' 10'' 18' 3'' 20' 9'' 19' 0'' 16' 7'' 13' 10'' 13' 10'' 13' 10''
600 USTN 16 25' 7'' 21' 8'' 19' 0'' 20' 11'' 19' 0'' 16' 7'' 17' 1'' 17' 1'' 14' 9'' 11' 5'' 11' 5'' 11' 5''24 20' 6'' 19' 0'' 16' 8'' 16' 9'' 16' 8'' 14' 0'' 13' 5'' 13' 5'' 12' 3'' 9' 0'' 9' 0'' 9' 0''
Minimum yield strength = 40 ksi2 Composite limiting heights based on single layer 5/8" thick gypsum board full height on each side with screws spaced 12" O.C. to framing members per ASTM C 754.
Dietrich UltraSTEEL® Framing’s 25-Gauge EQ Composite Limiting Heights (1 layer 5/8" thick gypsum wallboard)2
Stud MemberSpacing 5 psf 7.5 psf 10 psf 15 psf
(in.) L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/36012 15' 6'' 14' 9'' 12' 11'' 12' 8'' 12' 8'' — 11' 0'' 11' 0'' — 8' 8'' — —
162 USTN 16 14' 8'' 13' 4'' 11' 8'' 12' 0'' 11' 8'' — 10' 5'' — — — — —24 12' 11'' 11' 9'' — 10' 7'' — — 8' 8'' — — — — —12 16' 0'' 16' 0'' 14' 7'' 14' 3'' 14' 3'' 12' 5'' 12' 4'' 12' 4'' 10' 4'' 10' 1'' 10' 1'' —
250 USTN 16 16' 0'' 15' 1'' 13' 2'' 13' 1'' 13' 1'' 11' 6'' 11' 4'' 11' 4'' 10' 5'' 8' 11'' 8' 11'' —24 13' 9'' 13' 1'' 10' 10'' 11' 3'' 10' 10'' — 9' 9'' 9' 0'' — — — —12 23' 0'' 19' 5'' 16' 5'' 18' 10'' 16' 5'' 13' 5'' 16' 3'' 14' 3'' 11' 8'' 12' 10'' 11' 8'' 9' 6''
362 USTN 16 20' 1'' 16' 8'' 14' 3'' 16' 6'' 14' 3'' 12' 3'' 13' 11'' 12' 10'' 11' 1'' 11' 0'' 11' 0'' 9' 6''24 16' 8'' 14' 10'' 12' 1'' 13' 1'' 12' 1'' 9' 10'' 11' 2'' 10' 6'' 8' 6'' 8' 10'' 8' 6'' —12 24' 0'' 21' 2'' 18' 5'' 19' 7'' 18' 5'' 15' 9'' 17' 0'' 16' 6'' 13' 11'' 13' 4'' 13' 4'' 11' 5''
400 USTN 16 20' 10'' 19' 0'' 16' 3'' 17' 0'' 16' 3'' 13' 10'' 14' 6'' 14' 6'' 12' 5'' 11' 1'' 11' 1'' 10' 8''24 17' 1'' 16' 10'' 14' 1'' 13' 8'' 13' 8'' 11' 3'' 11' 7'' 11' 7'' 9' 6'' 8' 11'' 8' 11'' —12 30' 1'' 25' 0'' 21' 10'' 24' 7'' 21' 10'' 19' 1'' 20' 9'' 19' 10'' 17' 4'' 13' 10'' 13' 10'' 13' 10''
600 USTN 16 25' 7'' 22' 11'' 20' 0'' 20' 11'' 20' 0'' 17' 6'' 17' 1'' 17' 1'' 15' 7'' 11' 5'' 11' 5'' 11' 5''24 20' 6'' 20' 6'' 18' 1'' 16' 9'' 16' 11'' 14' 10'' 13' 5'' 13' 5'' 12' 7'' 9' 0'' 9' 0'' 9' 0''
Minimum yield strength = 40 ksi4 Composite limiting heights based on double layer 5/8" thick gypsum board full height on each side with screws spaced 12" O.C. to framing members per ASTM C 754.
Dietrich UltraSTEEL® Framing’s 25-Gauge EQ Composite Limiting Heights (2 layers 5/8" thick gypsum wallboard)4
Stud MemberSpacing 5 psf 7.5 psf 10 psf 15 psf
(in.) L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/36012 15' 6'' 13' 1'' 11' 5'' 12' 8'' 11' 5'' — 11' 0'' 10' 3'' — 8' 8'' — —
162 USTN 16 14' 8'' 11' 10'' 10' 4'' 12' 0'' 10' 4'' — 10' 5'' — — — — —24 12' 11'' 10' 5'' — 10' 7'' — — 8' 8'' — — — — —12 16' 0'' 15' 3'' 13' 4'' 14' 3'' 13' 4'' 11' 5'' 12' 4'' 12' 1'' 9' 9'' 10' 1'' 9' 9'' —
250 USTN 16 16' 0'' 13' 9'' 12' 0'' 13' 1'' 12' 0'' 10' 6'' 11' 4'' 10' 11'' 9' 6'' 8' 11'' 8' 11'' —24 13' 9'' 11' 11'' 10' 0'' 11' 3'' 10' 0'' — 9' 9'' 8' 6'' — — — —12 23' 0'' 18' 5'' 15' 8'' 18' 10'' 15' 8'' 13' 0'' 16' 3'' 13' 9'' 11' 5'' 12' 10'' 11' 5'' 9' 6''
362 USTN 16 20' 1'' 16' 1'' 13' 9'' 16' 6'' 13' 9'' 11' 10'' 13' 11'' 12' 4'' 10' 7'' 11' 0'' 10' 7'' 9' 2''24 16' 8'' 14' 2'' 11' 8'' 13' 1'' 11' 8'' 9' 8'' 11' 2'' 10' 3'' 8' 6'' 8' 10'' 8' 6'' —12 24' 0'' 20' 0'' 17' 5'' 19' 7'' 17' 5'' 14' 10'' 17' 0'' 15' 6'' 13' 2'' 13' 4'' 13' 2'' 10' 11''
400 USTN 16 20' 10'' 18' 0'' 15' 5'' 17' 0'' 15' 5'' 13' 1'' 14' 6'' 13' 9'' 11' 9'' 11' 1'' 11' 1'' 10' 1''24 17' 1'' 15' 10'' 13' 3'' 13' 8'' 13' 3'' 10' 9'' 11' 7'' 11' 5'' 9' 4'' 8' 11'' 8' 11'' —12 30' 1'' 24' 6'' 21' 5'' 24' 7'' 21' 5'' 18' 8'' 20' 9'' 19' 5'' 17' 0'' 13' 10'' 13' 10'' 13' 10''
600 USTN 16 25' 7'' 22' 5'' 19' 7'' 20' 11'' 19' 7'' 17' 1'' 17' 1'' 17' 1'' 15' 3'' 11' 5'' 11' 5'' 11' 5''24 20' 6'' 20' 0'' 17' 6'' 16' 9'' 16' 11'' 14' 5'' 13' 5'' 13' 5'' 12' 5'' 9' 0'' 9' 0'' 9' 0''
Minimum yield strength = 40 ksi3 Composite limiting heights based on double layer 1/2" thick gypsum board full height on each side with screws spaced 12" O.C. to framing members per ASTM C 754.
Dietrich UltraSTEEL® Framing’s 25-Gauge EQ Composite Limiting Heights (2 layers 1/2" thick gypsum wallboard)3
DMF07_028-029:DMF07_028-029 7/2/10 9:53 AM Page 29
Ultr
aSTE
EL®
Phys
ical
, Stru
ctur
al &
Com
posi
te L
imiti
ng H
eigh
t Inf
orm
atio
n
30 The place to stop…before the building starts! SM
25
20
15
10
5
0
20 DW-Gauge EQ Dietrich UltraSTEEL® Framing with 1 layer 1/2" thick gypsum wallboard Compared to Traditional SSMA 362S125-30
SSMA Traditional Metal Framing Dietrich UltraSTEEL® Framing
12 16 24 12 16 24 12 16 24 12 16 24 12 16 24 12 16 24 12 16 24 12 16 24 12 16 24
Feet
1 Composite limiting heights based on single layer 1/2" thick gypsum board full height on each side with screws spaced 12" O.C. to framing members per ASTM C 754. Tested to ICC acceptance criteria AC86
L/360 L/240 L/120 L/360 L/240 L/120L/360 L/240 L/120
5 PSF 7.5 PSF 10 PSF
PatentsProducts manufacturedusing the UltraSTEEL®
process are protected bygranted USA Patents (Nos.6,183,879 and 5,689,990)and granted CanadianPatent (No.2,149,914/1993) togetherwith design registration.
UltraSTEEL® is aTrademark of HadleyIndustries plc.
Stud MemberSpacing 5 psf 7.5 psf 10 psf 15 psf
(in.) L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/36012 17' 4" 13' 9" 12' 0" 15' 2" 12' 0" 7' 7" 13' 9" 8' 9" — 12' 0" — —
162 USTE 16 12' 8" 10' 1" 8' 10" 11' 1" 8' 10" 7' 8" 10' 1" 8' 0" — 8' 10" — —24 14' 0" 9' 0" — 12' 3" — — 9' 0" — — — — —12 19' 10" 15' 9" 13' 6" 17' 4" 13' 6" 10' 8" 15' 9" 11' 5" 9' 1" 13' 6" 9' 1" —
250 USTE 16 16' 5" 13' 0" 11' 4" 14' 4" 11' 4" 9' 11" 13' 0" 10' 4" 9' 0" 9' 5" f 9' 0" 7' 10"24 16' 0" 11' 10" 9' 5" 14' 0" 9' 5" 7' 8" 11' 10" 8' 1" — 9' 5" — —12 22' 0" 17' 5" 15' 1" 19' 2" 15' 1" 12' 10" 17' 5" 13' 5" 11' 5" 15' 1" 11' 5" 9' 9"
362 USTE 16 19' 4" 15' 4" 13' 5" 16' 11" 13' 5" 11' 9" 15' 4" 12' 2" 10' 8" 12' 11" f 10' 8" 9' 3"24 17' 8" 13' 8" 11' 7" 15' 5" 11' 7" 9' 11" 13' 8" 10' 4" 8' 10" 11' 7" 8' 10" 7' 7"12 24' 3" 19' 3" 16' 9" 21' 2" 16' 9" 14' 8" 19' 3" 15' 3" 13' 2" 16' 9" 13' 2" 11' 3"
400 USTE 16 21' 9" 17' 3" 15' 0" 19' 0" 15' 0" 13' 2" 17' 3" 13' 8" 11' 11" 15' 0" 11' 11" 10' 5"24 19' 5" 15' 5" 13' 3" 17' 0" 13' 3" 11' 1" 15' 5" 11' 8" 9' 10" 12' 10" f 9' 10" 8' 3"12 30' 8" 24' 4" 21' 3" 26' 9" 21' 3" 18' 7" 24' 4" 19' 4" 16' 10" 21' 3" 16' 10" 14' 7"
600 USTE 16 28' 0" 22' 3" 19' 5" 24' 6" 19' 5" 17' 0" 22' 3" 17' 8" 15' 5" 18' 9" f 15' 5" 13' 5"24 25' 0" 19' 10" 17' 4" 21' 10" f 17' 4" 14' 10" 18' 11" f 15' 7" 13' 2" 14' 3" s 13' 2" 11' 3"
f: Flexural stress controls allowable wall height s: Shear/web crippling control allowable wall height Minimum yield strength = 40 ksi
Dietrich UltraSTEEL® Framing’s 20 DW-Gauge EQ Composite Limiting Heights (1 layer 1/2" thick gypsum wallboard)1
Dietrich UltraSTEEL® Framing’s 20 DW-Gauge EQ Physical and Structural Properties
Notes: Section properties are determined in accordance with AISI-NASPEC 2001.Section properties are conservatively calculated using the thickness and yield strength of the base material, prior to the Dietrich UltraSTEEL® forming process.Calculated effective moment of inertia (Ixe) is based on serviceability determination.Effective section properties and moment capacity did not incorporate stress increase as a result of cold work of forming.Yield Strength = 40 ksi
Base Effective Gross Section Properties Effective Section Allowable Torsional Section PropertiesMember Metal Metal Weight Properties Moment
Designation Thickness Thickness Area Ix rx Iy ry Ixe Sxe Ma Xo J Cw Ro Beta(inches) (inches) (lbs/ft) (in2) (in4) (in) (in4) (in) (in4) (in3) (in-lbs) (in) (10-5 in4) (in6) (in) (degree)
162 USTE 0.025 0.055 0.391 0.115 0.054 0.685 0.024 0.455 0.052 0.048 1,157 -1.050 2.653 0.014 1.333 0.380
250 USTE 0.025 0.055 0.469 0.138 0.142 1.015 0.028 0.447 0.136 0.090 2,166 -0.923 3.184 0.034 1.442 0.591
362 USTE 0.025 0.055 0.570 0.168 0.334 1.412 0.031 0.430 0.320 0.119 2,841 -0.804 3.868 0.078 1.681 0.771
400 USTE 0.025 0.055 0.604 0.177 0.421 1.540 0.032 0.423 0.403 0.132 3,155 -0.771 4.095 0.098 1.774 0.811
600 USTE 0.025 0.055 0.782 0.230 1.111 2.197 0.035 0.391 1.017 0.234 5,593 -0.637 5.310 0.247 2.321 0.925
request a quote online @
DMF07_030-031:DMF07_030-031 7/2/10 9:57 AM Page 30
UltraSTEEL® FramingU
ltraSTEEL®
Physical, Structural & Com
posite Limiting H
eight Information
31For more information or to contact a sales representative, see page 3
Stud MemberSpacing 5 psf 7.5 psf 10 psf 15 psf
(in.) L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/36012 18' 1'' 14' 5'' 12' 7'' 15' 10'' 12' 7'' 7' 11'' 14' 5'' 9' 4'' — 12' 7'' — —
162 USTE 16 13' 7'' 10' 9'' 9' 5'' 11' 10'' 9' 5'' 8' 3'' 10' 9'' 8' 7'' — 9' 5'' — —24 15' 5'' 9' 9'' — 13' 6'' — — 9' 9'' — — — — —12 21' 1'' 16' 9'' 14' 5'' 18' 5'' 14' 5'' 11' 2'' 16' 9'' 12' 0'' 9' 5'' 14' 5'' 9' 5'' —
250 USTE 16 17' 2'' 13' 8'' 11' 11'' 15' 0'' 11' 11'' 10' 5'' 13' 8'' 10' 10'' 9' 5'' 9' 6'' 9' 5'' 8' 3''24 17' 1'' 12' 6'' 9' 9'' 14' 11'' 9' 9'' 7' 9'' 12' 6'' 8' 4'' — 9' 9'' — —12 22' 6'' 17' 10'' 15' 5'' 19' 8'' 15' 5'' 13' 0'' 17' 10'' 13' 8'' 11' 6'' 15' 5'' 11' 6'' 9' 9''
362 USTE 16 19' 8'' 15' 8'' 13' 8'' 17' 2'' 13' 8'' 11' 11'' 15' 8'' 12' 5'' 10' 10'' 12' 11'' 10' 10'' 9' 6''24 18' 3'' 14' 0'' 11' 10'' 15' 10'' 11' 10'' 10' 0'' 14' 0'' 10' 6'' 8' 11'' 11' 10'' 8' 11'' 7' 9''12 24' 11'' 19' 9'' 17' 3'' 21' 9'' 17' 3'' 15' 1'' 19' 9'' 15' 8'' 13' 6'' 17' 3'' 13' 6'' 11' 5''
400 USTE 16 22' 3'' 17' 8'' 15' 5'' 19' 5'' 15' 5'' 13' 6'' 17' 8'' 14' 0'' 12' 3'' 15' 5'' 12' 3'' 10' 8''24 20' 1'' 15' 11'' 13' 8'' 17' 6'' 13' 8'' 11' 4'' 15' 11'' 11' 11'' 9' 11'' 12' 10'' 9' 11'' 8' 5''12 30' 11'' 24' 7'' 21' 5'' 27' 0'' 21' 5'' 18' 9'' 24' 7'' 19' 6'' 17' 0'' 21' 5'' 17' 0'' 14' 9''
600 USTE 16 28' 4'' 22' 6'' 19' 8'' 24' 9'' 19' 8'' 17' 2'' 22' 6'' 17' 10'' 15' 7'' 18' 10'' 15' 7'' 13' 7''24 25' 5'' 20' 2'' 17' 8'' 21' 11'' 17' 8'' 15' 0'' 18' 11'' 15' 9'' 13' 3'' 14' 4'' 13' 3'' 11' 5''
Minimum yield strength = 40 ksi2 Composite limiting heights based on single layer 5/8" thick gypsum board full height on each side with screws spaced 12" O.C. to framing members per ASTM C 754.
Dietrich UltraSTEEL® Framing’s 20 DW-Gauge EQ Composite Limiting Heights (1 layer 5/8" thick gypsum wallboard)2
Stud MemberSpacing 5 psf 7.5 psf 10 psf 15 psf
(in.) L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/36012 23' 6'' 20' 4'' 17' 9'' 19' 5'' 17' 9'' 9' 9'' 16' 10'' 12' 5'' — 13' 9'' — —
162 USTE 16 18' 2'' 14' 5'' 12' 7'' 15' 11'' 12' 7'' 11' 0'' 14' 5'' 11' 6'' — 12' 2'' — —24 17' 7'' 13' 2'' — 14' 4'' — — 12' 5'' — — — — —12 23' 6'' 21' 10'' 18' 8'' 21' 3'' 18' 8'' 13' 7'' 18' 5'' 14' 11'' 10' 11'' 15' 0'' 10' 11'' —
250 USTE 16 21' 4'' 16' 11'' 14' 10'' 18' 8'' 14' 10'' 12' 11'' 16' 3'' 13' 5'' 11' 9'' 9' 6'' 9' 6'' 9' 6''24 19' 2'' 15' 10'' 11' 8'' 15' 8'' 11' 8'' 8' 6'' 13' 5'' 9' 4'' — 10' 3'' — —12 25' 5'' 20' 2'' 17' 4'' 22' 3'' 17' 4'' 14' 0'' 20' 2'' 14' 11'' 12' 1'' 17' 3'' 12' 1'' 9' 10''
362 USTE 16 21' 5'' 17' 0'' 14' 10'' 18' 9'' 14' 10'' 13' 0'' 17' 0'' 13' 6'' 11' 10'' 12' 11'' 11' 10'' 10' 4''24 20' 11'' 15' 8'' 12' 9'' 17' 11'' 12' 9'' 10' 4'' 15' 6'' 11' 0'' 9' 0'' 12' 2'' 9' 0'' 7' 9''12 28' 6'' 22' 7'' 19' 9'' 24' 11'' 19' 9'' 17' 3'' 21' 10'' 17' 11'' 15' 4'' 17' 10'' 15' 4'' 12' 8''
400 USTE 16 25' 2'' 20' 0'' 17' 5'' 22' 0'' 17' 5'' 15' 3'' 19' 3'' 15' 10'' 13' 10'' 15' 9'' 13' 10'' 12' 1''24 22' 7'' 18' 5'' 15' 8'' 18' 5'' 15' 8'' 12' 4'' 16' 0'' 13' 3'' 10' 5'' 12' 10'' 10' 5'' 8' 5''12 32' 3'' 25' 7'' 22' 5'' 28' 2'' 22' 5'' 19' 7'' 25' 7'' 20' 4'' 17' 9'' 21' 7'' 17' 9'' 15' 3''
600 USTE 16 29' 10'' 23' 8'' 20' 8'' 26' 1'' 20' 8'' 18' 1'' 23' 1'' 18' 9'' 16' 5'' 18' 10'' 16' 5'' 14' 4''24 26' 10'' 21' 9'' 19' 1'' 21' 11'' 19' 1'' 15' 10'' 18' 11'' 16' 10'' 13' 7'' 14' 4'' 13' 7'' 11' 5''
Minimum yield strength = 40 ksi4 Composite limiting heights based on double layer 5/8" thick gypsum board full height on each side with screws spaced 12" O.C. to framing members per ASTM C 754.
Dietrich UltraSTEEL® Framing’s 20 DW-Gauge EQ Composite Limiting Heights (2 layers 5/8" thick gypsum wallboard)4
Stud MemberSpacing 5 psf 7.5 psf 10 psf 15 psf
(in.) L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/36012 22' 7'' 17' 11'' 15' 8'' 19' 5'' 15' 8'' 9' 0'' 16' 10'' 11' 1'' — 13' 9'' — —
162 USTE 16 16' 3'' 12' 11'' 11' 3'' 14' 3'' 11' 3'' 9' 10'' 12' 11'' 10' 3'' — 11' 3'' — —24 17' 7'' 11' 9'' — 14' 4'' — — 11' 9'' — — — — —12 23' 6'' 19' 9'' 16' 11'' 21' 3'' 16' 11'' 12' 7'' 18' 5'' 13' 8'' 10' 3'' 15' 0'' 10' 3'' —
250 USTE 16 19' 7'' 15' 7'' 13' 7'' 17' 2'' 13' 7'' 11' 11'' 15' 7'' 12' 4'' 10' 10'' 9' 6'' 9' 6'' 9' 5''24 19' 2'' 14' 5'' 10' 10'' 15' 8'' 10' 10'' 8' 2'' 13' 5'' 8' 11'' — 10' 3'' — —12 24' 2'' 19' 2'' 16' 6'' 21' 2'' 16' 6'' 13' 7'' 19' 2'' 14' 4'' 11' 10'' 16' 6'' 11' 10'' 9' 10''
362 USTE 16 20' 8'' 16' 5'' 14' 4'' 18' 1'' 14' 4'' 12' 6'' 16' 5'' 13' 0'' 11' 5'' 12' 11'' 11' 5'' 9' 11''24 19' 9'' 14' 11'' 12' 4'' 17' 2'' 12' 4'' 10' 2'' 14' 11'' 10' 9'' 8' 11'' 12' 2'' 8' 11'' 7' 9''12 27' 0'' 21' 5'' 18' 9'' 23' 7'' 18' 9'' 16' 4'' 21' 5'' 17' 0'' 14' 7'' 17' 10'' 14' 7'' 12' 2''
400 USTE 16 23' 11'' 19' 0'' 16' 7'' 20' 11'' 16' 7'' 14' 6'' 19' 0'' 15' 1'' 13' 2'' 15' 9'' 13' 2'' 11' 6''24 21' 11'' 17' 4'' 14' 10'' 18' 5'' 14' 10'' 11' 11'' 16' 0'' 12' 8'' 10' 2'' 12' 10'' 10' 2'' 8' 5''12 31' 8'' 25' 2'' 22' 0'' 27' 8'' 22' 0'' 19' 3'' 25' 2'' 20' 0'' 17' 5'' 21' 7'' 17' 5'' 15' 1''
600 USTE 16 29' 2'' 23' 2'' 20' 3'' 25' 6'' 20' 3'' 17' 8'' 23' 1'' 18' 5'' 16' 1'' 18' 10'' 16' 1'' 14' 0''24 26' 7'' 21' 1'' 18' 5'' 21' 11'' 18' 5'' 15' 5'' 18' 11'' 16' 5'' 13' 5'' 14' 4'' 13' 5'' 11' 5''
Minimum yield strength = 40 ksi3 Composite limiting heights based on double layer 1/2" thick gypsum board full height on each side with screws spaced 12" O.C. to framing members per ASTM C 754.
Dietrich UltraSTEEL® Framing’s 20 DW-Gauge EQ Composite Limiting Heights (2 layers 1/2" thick gypsum wallboard)3
DMF07_030-031:DMF07_030-031 7/2/10 9:57 AM Page 31
Ultr
aSTE
EL®
Phys
ical
, Stru
ctur
al &
Com
posi
te L
imiti
ng H
eigh
t Inf
orm
atio
n
32 The place to stop…before the building starts! SM
Dietrich UltraSTEEL® Framing’s 20 STR-Gauge* EQ Physical and Structural Properties
Notes: Section properties are determined in accordance with AISI-NASPEC 2001.Section properties are conservatively calculated using the thickness and yield strength of the base material, prior to the Dietrich UltraSTEEL® forming process.Calculated effective moment of inertia (Ixe) is based on serviceability determination.Effective section properties and moment capacity did not incorporate stress increase as a result of cold work of forming.Yield Strength = 40 ksi
Base Effective Gross Section Properties Effective Section Allowable Torsional Section PropertiesMember Metal Metal Weight Properties Moment
Designation Thickness Thickness Area Ix rx Iy ry Ixe Sxe Ma Xo J Cw Ro Beta(inches) (inches) (lbs/ft) (in2) (in4) (in) (in4) (in) (in4) (in3) (in-lbs) (in) (10-5 in4) (in6) (in) (degree)
162 USTX 0.028 0.060 0.436 0.128 0.060 0.683 0.026 0.453 0.059 0.056 1,347 -1.046 3.714 0.015 1.329 0.381
250 USTX 0.028 0.060 0.524 0.154 0.158 1.013 0.031 0.445 0.154 0.104 2,481 -0.919 4.460 0.038 1.438 0.592
362 USTX 0.028 0.060 0.637 0.187 0.372 1.410 0.034 0.428 0.364 0.140 3,349 -0.800 5.420 0.086 1.677 0.772
400 USTX 0.028 0.060 0.674 0.198 0.469 1.538 0.035 0.422 0.458 0.155 3,723 -0.768 5.740 0.108 1.770 0.812
600 USTX 0.028 0.060 0.875 0.257 1.240 2.195 0.039 0.389 1.150 0.278 6,654 -0.634 7.447 0.274 2.318 0.925
1 Composite limiting heights based on single layer 1/2" thick gypsum board full height on each side with screws spaced 12" O.C. to framing members per ASTM C 754. Tested to ICC acceptance criteria AC86
Stud MemberSpacing 5 psf 7.5 psf 10 psf 15 psf
(in.) L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/36012 14' 8" 11' 8" 9' 8" 12' 10" 9' 8" 8' 1" 11' 8" 8' 6" — 9' 8" — —
162 USTX 16 12' 4" 9' 10" 8' 7" 10' 10" 8' 7" — 9' 10" 7' 10" — 8' 7" — —24 12' 3" 8' 10" — 10' 2" — — 8' 10" — — — — —12 18' 8" 14' 10" 12' 8" 16' 4" 12' 8" 10' 9" 14' 10" 11' 3" 9' 7" 12' 8" 9' 7" 8' 2"
250 USTX 16 16' 4" 13' 0" 11' 4" 14' 3" 11' 4" 9' 11" 13' 0" 10' 4" 9' 0" 11' 4" 9' 0" 7' 10"24 15' 4" 11' 8" 9' 10" 13' 3" 9' 10" 8' 4" 11' 8" 8' 9" — 9' 10" — —12 23' 5" 18' 7" 16' 3" 20' 5" 16' 3" 13' 11" 18' 7" 14' 7" 12' 5" 16' 3" 12' 5" 10' 7"
362 USTX 16 20' 11" 16' 7" 14' 6" 18' 3" 14' 6" 12' 8" 16' 7" 13' 2" 11' 6" 14' 6" 11' 6" 10' 1"24 18' 11" 14' 11" 12' 8" 16' 7" 12' 8" 10' 10" 14' 11" 11' 4" 9' 8" 12' 8" 9' 8" 8' 4"12 25' 0" 19' 10" 17' 4" 21' 10" 17' 4" 15' 1" 19' 10" 15' 9" 13' 8" 17' 4" 13' 8" 11' 9"
400 USTX 16 22' 8" 17' 11" 15' 8" 19' 9" 15' 8" 13' 8" 17' 11" 14' 3" 12' 5" 15' 8" 12' 5" 10' 11"24 20' 1" 16' 0" 13' 11" 17' 7" 13' 11" 11' 10" 16' 0" 12' 5" 10' 7" 12' 2" s 10' 7" 9' 0"12 33' 1" 26' 3" 22' 11" 28' 10" 22' 11" 20' 0" 26' 3" 20' 10" 18' 2" 22' 11" 18' 2" 15' 9"
600 USTX 16 30' 3" 24' 0" 21' 0" 26' 5" 21' 0" 18' 4" 24' 0" 19' 1" 16' 8" 20' 3" s 16' 8" 14' 7"24 27' 0" 21' 5" 18' 9" 23' 7" 18' 9" 16' 1" 21' 5" 16' 10" 14' 4" 15' 0" s 14' 4" 12' 2"
f: Flexural stress controls allowable wall height s: Shear/web crippling control allowable wall height Minimum yield strength = 40 ksi
Dietrich UltraSTEEL® Framing’s 20 STR-Gauge* EQ Composite Limiting Heights (1 layer 1/2" thick gypsum wallboard)1
25
20
15
10
5
0
20 STR-Gauge* EQ Dietrich UltraSTEEL® Framing with 1 layer 1/2" thick gypsum wallboard Compared to Traditional SSMA 362S125-33
SSMA Traditional Metal Framing Dietrich UltraSTEEL® Framing
12 16 24 12 16 24 12 16 24 12 16 24 12 16 24 12 16 24 12 16 24 12 16 24 12 16 24
Feet
L/360 L/240 L/120 L/360 L/240 L/120L/360 L/240 L/120
5 PSF 7.5 PSF 10 PSF
PatentsProducts manufacturedusing the UltraSTEEL®
process are protected bygranted USA Patents (Nos.6,183,879 and 5,689,990)and granted CanadianPatent (No.2,149,914/1993) togetherwith design registration.
UltraSTEEL® is aTrademark of HadleyIndustries plc.
*Available in limited markets
request a quote online @
DMF07_032-033:DMF07_032-033 7/2/10 9:59 AM Page 32
UltraSTEEL® FramingU
ltraSTEEL®
Physical, Structural & Com
posite Limiting H
eight Information
33For more information or to contact a sales representative, see page 3
Stud MemberSpacing 5 psf 7.5 psf 10 psf 15 psf
(in.) L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/36012 15' 8'' 12' 5'' 10' 2'' 13' 8'' 10' 2'' 8' 5'' 12' 5'' 8' 11'' — 10' 2'' — —
162 USTX 16 13' 0'' 10' 4'' 9' 0'' 11' 4'' 9' 0'' — 10' 4'' 8' 2'' — 9' 0'' — —24 13' 2'' 9' 4'' — 10' 10'' — — 9' 4'' — — — — —12 19' 6'' 15' 5'' 13' 2'' 17' 0'' 13' 2'' 11' 1'' 15' 5'' 11' 7'' 9' 10'' 13' 2'' 9' 10'' 8' 4''
250 USTX 16 16' 11'' 13' 5'' 11' 9'' 14' 10'' 11' 9'' 10' 3'' 13' 5'' 10' 8'' 9' 4'' 11' 9'' 9' 4'' 8' 2''24 16' 1'' 12' 2'' 10' 2'' 13' 10'' 10' 2'' 8' 7'' 12' 2'' 9' 0'' — 10' 2'' — —12 24' 0'' 19' 1'' 16' 8'' 21' 0'' 16' 8'' 14' 2'' 19' 1'' 14' 11'' 12' 8'' 16' 8'' 12' 8'' 10' 9''
362 USTX 16 21' 5'' 17' 0'' 14' 10'' 18' 8'' 14' 10'' 13' 0'' 17' 0'' 13' 6'' 11' 9'' 14' 10'' 11' 9'' 10' 4''24 19' 7'' 15' 4'' 12' 11'' 17' 1'' 12' 11'' 11' 0'' 15' 4'' 11' 6'' 9' 10'' 12' 10'' 9' 10'' 8' 5''12 25' 6'' 20' 3'' 17' 8'' 22' 4'' 17' 8'' 15' 6'' 20' 3'' 16' 1'' 14' 0'' 17' 8'' 14' 0'' 12' 0''
400 USTX 16 23' 2'' 18' 4'' 16' 0'' 20' 3'' 16' 0'' 14' 0'' 18' 4'' 14' 7'' 12' 9'' 16' 0'' 12' 9'' 11' 1''24 20' 8'' 16' 5'' 14' 4'' 18' 1'' 14' 4'' 12' 1'' 16' 5'' 12' 8'' 10' 8'' 12' 2'' 10' 8'' 9' 1''12 33' 6'' 26' 7'' 23' 3'' 29' 3'' 23' 3'' 20' 4'' 26' 7'' 21' 1'' 18' 5'' 23' 3'' 18' 5'' 15' 11''
600 USTX 16 30' 9'' 24' 5'' 21' 4'' 26' 10'' 21' 4'' 18' 8'' 24' 5'' 19' 5'' 16' 11'' 20' 3'' 16' 11'' 14' 9''24 27' 7'' 21' 11'' 19' 2'' 24' 1'' 19' 2'' 16' 4'' 21' 11'' 17' 2'' 14' 6'' 15' 0'' 14' 6'' 12' 3''
Minimum yield strength = 40 ksi2 Composite limiting heights based on single layer 5/8" thick gypsum board full height on each side with screws spaced 12" O.C. to framing members per ASTM C 754.
Dietrich UltraSTEEL® Framing’s 20 STR-Gauge* EQ Composite Limiting Heights (1 layer 5/8" thick gypsum wallboard)2
Stud MemberSpacing 5 psf 7.5 psf 10 psf 15 psf
(in.) L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/36012 21' 1'' 16' 8'' 13' 4'' 17' 6'' 13' 4'' 10' 8'' 15' 2'' 11' 5'' — 12' 5'' — —
162 USTX 16 16' 9'' 13' 3'' 11' 7'' 14' 7'' 11' 7'' — 13' 3'' 10' 6'' — 10' 6'' — —24 16' 0'' 12' 2'' — 13' 0'' — — 11' 3'' — — — — —12 23' 6'' 19' 1'' 15' 11'' 20' 9'' 15' 11'' 13' 1'' 17' 11'' 13' 10'' 11' 4'' 14' 8'' 11' 4'' 9' 4''
250 USTX 16 20' 4'' 16' 1'' 14' 1'' 17' 9'' 14' 1'' 12' 4'' 15' 9'' 12' 9'' 11' 2'' 12' 2'' 11' 2'' 9' 9''24 18' 5'' 14' 11'' 12' 2'' 15' 1'' 12' 2'' 9' 11'' 13' 0'' 10' 6'' — 10' 7'' — —12 27' 8'' 21' 11'' 19' 2'' 24' 2'' 19' 2'' 16' 0'' 21' 11'' 16' 11'' 13' 11'' 18' 3'' 13' 11'' 11' 7''
362 USTX 16 24' 3'' 19' 3'' 16' 9'' 21' 2'' 16' 9'' 14' 8'' 19' 3'' 15' 3'' 13' 4'' 15' 10'' 13' 4'' 11' 8''24 22' 5'' 17' 9'' 14' 8'' 18' 3'' 14' 8'' 12' 1'' 15' 10'' 12' 9'' 10' 7'' 12' 10'' 10' 7'' 8' 10''12 28' 10'' 22' 11'' 20' 0'' 25' 2'' 20' 0'' 17' 6'' 22' 11'' 18' 2'' 15' 9'' 19' 3'' 15' 9'' 13' 4''
400 USTX 16 26' 1'' 20' 8'' 18' 1'' 22' 10'' 18' 1'' 15' 10'' 20' 6'' 16' 5'' 14' 4'' 16' 9'' 14' 4'' 12' 6''24 23' 8'' 18' 10'' 16' 5'' 19' 4'' 16' 5'' 13' 5'' 16' 9'' 14' 3'' 11' 8'' 12' 2'' 11' 8'' 9' 7''12 35' 6'' 28' 9'' 25' 1'' 31' 7'' 25' 1'' 21' 11'' 28' 9'' 22' 10'' 19' 11'' 23' 11'' 19' 11'' 17' 0''
600 USTX 16 33' 6'' 26' 7'' 23' 3'' 29' 3'' 23' 3'' 20' 3'' 26' 7'' 21' 1'' 18' 5'' 20' 3'' 18' 5'' 16' 1''24 30' 9'' 24' 5'' 21' 4'' 25' 5'' 21' 4'' 17' 10'' 22' 0'' 18' 11'' 15' 5'' 15' 0'' 15' 0'' 12' 7''
Minimum yield strength = 40 ksi4 Composite limiting heights based on double layer 5/8" thick gypsum board full height on each side with screws spaced 12" O.C. to framing members per ASTM C 754.*Available in limited markets
Dietrich UltraSTEEL® Framing’s 20 STR-Gauge* EQ Composite Limiting Heights (2 layers 5/8" thick gypsum wallboard)4
Stud MemberSpacing 5 psf 7.5 psf 10 psf 15 psf
(in.) L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/360 L/120 L/240 L/36012 18' 10'' 14' 11'' 12' 0'' 16' 5'' 12' 0'' 9' 9'' 14' 11'' 10' 4'' — 12' 0'' — —
162 USTX 16 15' 2'' 12' 0'' 10' 6'' 13' 3'' 10' 6'' — 12' 0'' 9' 6'' — 10' 6'' — —24 16' 0'' 11' 0'' — 13' 0'' — — 11' 0'' — — — — —12 22' 1'' 17' 7'' 14' 9'' 19' 4'' 14' 9'' 12' 2'' 17' 7'' 12' 11'' 10' 8'' 14' 8'' 10' 8'' 8' 10''
250 USTX 16 18' 11'' 15' 0'' 13' 1'' 16' 6'' 13' 1'' 11' 5'' 15' 0'' 11' 11'' 10' 5'' 12' 2'' 10' 5'' 9' 1''24 18' 5'' 13' 9'' 11' 4'' 15' 1'' 11' 4'' 9' 4'' 13' 0'' 9' 11'' — 10' 7'' — —12 26' 1'' 20' 9'' 18' 1'' 22' 10'' 18' 1'' 15' 3'' 20' 9'' 16' 1'' 13' 5'' 18' 1'' 13' 5'' 11' 2''
362 USTX 16 23' 0'' 18' 3'' 15' 11'' 20' 1'' 15' 11'' 13' 11'' 18' 3'' 14' 6'' 12' 8'' 15' 10'' 12' 8'' 11' 1''24 21' 6'' 16' 9'' 13' 11'' 18' 3'' 13' 11'' 11' 8'' 15' 10'' 12' 3'' 10' 3'' 12' 10'' 10' 3'' 8' 7''12 27' 5'' 21' 10'' 19' 1'' 24' 0'' 19' 1'' 16' 8'' 21' 10'' 17' 3'' 15' 0'' 19' 1'' 15' 0'' 12' 9''
400 USTX 16 24' 10'' 19' 9'' 17' 3'' 21' 9'' 17' 3'' 15' 1'' 19' 9'' 15' 8'' 13' 8'' 16' 9'' 13' 8'' 11' 11''24 22' 5'' 17' 10'' 15' 6'' 19' 4'' 15' 6'' 12' 10'' 16' 9'' 13' 7'' 11' 3'' 12' 2'' 11' 3'' 9' 4''12 35' 1'' 27' 10'' 24' 4'' 30' 8'' 24' 4'' 21' 3'' 27' 10'' 22' 1'' 19' 4'' 23' 11'' 19' 4'' 16' 7''
600 USTX 16 32' 4'' 25' 8'' 22' 5'' 28' 3'' 22' 5'' 19' 7'' 25' 8'' 20' 5'' 17' 10'' 20' 3'' 17' 10'' 15' 7''24 29' 5'' 23' 4'' 20' 5'' 25' 5'' 20' 5'' 17' 3'' 22' 0'' 18' 2'' 15' 0'' 15' 0'' 15' 0'' 12' 6''
Minimum yield strength = 40 ksi3 Composite limiting heights based on double layer 1/2" thick gypsum board full height on each side with screws spaced 12" O.C. to framing members per ASTM C 754.
Dietrich UltraSTEEL® Framing’s 20 STR-Gauge* EQ Composite Limiting Heights (2 layers 1/2" thick gypsum wallboard)3
DMF07_032-033:DMF07_032-033 7/2/10 9:59 AM Page 33
Inte
rior
(Dry
wal
l) N
onlo
ad-B
earin
g U
ltraS
TEEL
®Fr
amin
g
34
B DF
UltraSTEEL® Drywall Nonload-Bearing(Nonstructural) Track (UT-Series™)Economical top and bottom plate or runner used to secure drywall studsto the floor and ceiling.■ Available in multiple leg heights■ Standard 10’ lengths, custom lengths available■ Available Sizes:
1-5/8”, 2-1/2”, 3-1/2”*, 3-5/8”, 4”, 5-1/2”* and 6”■ Available Gauges: 25 EQ, 20 DW EQ and 20 STR* EQ
EQ = Equivalent to traditional metal stud gauges■ Product Code Designators
(Product ) (Gauge) (Leg)UT N = 25EQ B = 1-1/4” Leg
E = 20DWEQ D = 2” LegX = 20STREQ* F = 3” Leg
* Available in limited markets
UltraSTEEL® track or runner ismanufactured from corrosion-resistant, galvanized steel forcorresponding stud sizes andgauges. The inside width of thetrack or web is equivalent to theoutside width of the studs. Varyingleg heights are available fordeflection conditions or toaccommodate uneven orinconsistent floor or ceiling conditions.
1-1/4" Leg Drywall Track 2" Leg Drywall Track 3" Leg Drywall Track
Drywall Track
The place to stop…before the building starts! SMrequest a quote online @
DMF07_034-035:DMF07_034-035 7/2/10 10:01 AM Page 34
UltraSTEEL® FramingInterior (D
rywall) N
onload-Bearing UltraSTEEL
®Fram
ing
35For more information or to contact a sales representative, see page 3
Notes: Section properties are determined in accordance with AISI-NASPEC 2001.Section properties are conservatively calculated using the thickness and yieldstrength of the base material, prior to the Dietrich UltraSTEEL® forming process.Calculated effective moment of inertia (Ixe) is based on serviceability determination.Effective section properties and moment capacity did not incorporate stressincrease as a result of cold work of forming.
Yield Strength = 40 ksi* Depth over thickness ratio ( h⁄t ) is greater than 300.**Available in limited markets
Dietrich UltraSTEEL® Track Section Properties 25-Gauge EQMember Information Gross Section Properties Effective Properties Torsional Properties
Nominal Base Effective
Depth Designation Leg Gauge Mils Metal Metal Weight Area Ix Sx Rx Iy Sy Ry Ixe Sxe Mxa Xo J*1000 Cw Ro B
(in.) (in.) Thickness Thickness (lb./ft.) (in.2) (in.4) (in.3) (in.) (in.4) (in.3) (in.) (in.4) (in.3) (in.-lb.) (in.) (in.4) (in.6) (in.) Beta(in.) (in.)
UTNB 1.25 25 EQ 15 0.015 0.035 0.219 0.064 0.032 0.038 0.702 0.011 0.013 0.412 0.020 0.017 400 -0.887 0.005 0.005 1.204 0.457
1.625 UTND 2.00 25 EQ 15 0.015 0.035 0.300 0.088 0.048 0.058 0.736 0.039 0.047 0.662 0.025 0.016 389 -1.587 0.007 0.019 1.870 0.280
UTNF 3.00 25 EQ 15 0.015 0.035 0.407 0.120 0.069 0.083 0.759 0.115 0.139 0.980 0.027 0.017 410 -2.551 0.010 0.059 2.837 0.191
UTNB 1.25 25 EQ 15 0.015 0.035 0.266 0.078 0.082 0.065 1.023 0.013 0.010 0.401 0.058 0.026 627 -0.776 0.007 0.014 1.345 0.668
2.500 UTND 2.00 25 EQ 15 0.015 0.035 0.347 0.102 0.119 0.094 1.082 0.045 0.035 0.662 0.067 0.026 621 -1.437 0.008 0.050 1.917 0.438
UTNF 3.00 25 EQ 15 0.015 0.035 0.454 0.134 0.169 0.134 1.126 0.132 0.105 0.995 0.069 0.027 653 -2.371 0.011 0.153 2.807 0.287
UTNB 1.25 25 EQ 15 0.015 0.035 0.327 0.096 0.191 0.105 1.411 0.014 0.008 0.382 0.133 0.038 920 -0.671 0.008 0.033 1.609 0.826
3.625 UTND 2.00 25 EQ 15 0.015 0.035 0.407 0.120 0.270 0.148 1.501 0.050 0.028 0.649 0.144 0.039 923 -1.287 0.010 0.117 2.081 0.618
UTNF 3.00 25 EQ 15 0.015 0.035 0.515 0.151 0.374 0.205 1.573 0.150 0.082 0.995 0.154 0.039 939 -2.178 0.013 0.352 2.865 0.422
UTNB 1.25 25 EQ 15 0.015 0.035 0.347 0.102 0.241 0.119 1.537 0.014 0.007 0.375 0.162 0.042 1018 -0.643 0.008 0.042 1.707 0.858
4.000 UTND 2.00 25 EQ 15 0.015 0.035 0.428 0.126 0.336 0.167 1.636 0.052 0.026 0.643 0.177 0.043 1023 -1.244 0.010 0.147 2.153 0.666
UTNF 3.00 25 EQ 15 0.015 0.035 0.535 0.157 0.464 0.230 1.717 0.155 0.077 0.992 0.188 0.044 1053 -2.122 0.013 0.440 2.904 0.466
UTNB 1.25 25 EQ 15 0.015 0.035 0.454 0.134 0.636 0.211 2.182 0.016 0.005 0.343 — — — -0.526 0.011 0.107 2.270 0.946
6.000* UTND 2.00 25 EQ 15 0.015 0.035 0.535 0.157 0.850 0.282 2.325 0.058 0.019 0.609 — — — -1.061 0.013 0.377 2.627 0.837
UTNF 3.00 25 EQ 15 0.015 0.035 0.643 0.189 1.136 0.377 2.452 0.176 0.058 0.966 — — — -1.869 0.016 1.118 3.231 0.665
Dietrich UltraSTEEL® Track Section Properties 20 STR-Gauge** EQMember Information Gross Section Properties Effective Properties Torsional Properties
Nominal Base Effective
Depth Designation Leg Gauge Mils Metal Metal Weight Area Ix Sx Rx Iy Sy Ry Ixe Sxe Mxa Xo J*1000 Cw Ro B
(in.) (in.) Thickness Thickness (lb./ft.) (in.2) (in.4) (in.3) (in.) (in.4) (in.3) (in.) (in.4) (in.3) (in.-lb.) (in.) (in.4) (in.6) (in.) Beta(in.) (in.)
UTXB 1.25 20 EQ 28 0.028 0.061 0.409 0.120 0.060 0.071 0.706 0.020 0.024 0.410 0.046 0.041 987 -0.879 0.035 0.010 1.200 0.463
1.625 UTXD 2.00 20 EQ 28 0.028 0.061 0.559 0.164 0.090 0.107 0.741 0.072 0.085 0.660 0.056 0.044 1063 -1.578 0.048 0.036 1.864 0.283
UTXF 3.00 20 EQ 28 0.028 0.061 0.760 0.223 0.131 0.155 0.765 0.214 0.254 0.978 0.065 0.047 1114 -2.542 0.065 0.112 2.829 0.193
UTXB 1.25 20 EQ 28 0.028 0.061 0.497 0.146 0.154 0.120 1.027 0.023 0.018 0.398 0.123 0.076 1820 -0.769 0.042 0.026 1.343 0.673
2.500 UTXD 2.00 20 EQ 28 0.028 0.061 0.647 0.190 0.225 0.176 1.087 0.083 0.065 0.660 0.148 0.082 1971 -1.430 0.055 0.094 1.913 0.442
UTXF 3.00 20 EQ 28 0.028 0.061 0.848 0.249 0.319 0.249 1.132 0.246 0.192 0.993 0.173 0.083 1999 -2.362 0.072 0.287 2.801 0.289
UTXB 1.25 20 EQ 28 0.028 0.061 0.610 0.179 0.358 0.195 1.414 0.026 0.014 0.379 0.294 0.132 3165 -0.665 0.052 0.062 1.608 0.829
3.625 UTXD 2.00 20 EQ 28 0.028 0.061 0.760 0.223 0.506 0.275 1.505 0.093 0.051 0.646 0.356 0.128 3059 -1.280 0.065 0.219 2.079 0.621
UTXF 3.00 20 EQ 28 0.028 0.061 0.961 0.282 0.703 0.382 1.578 0.278 0.151 0.993 0.420 0.125 2995 -2.170 0.082 0.658 2.861 0.425
UTXB 1.25 20 EQ 28 0.028 0.061 0.647 0.190 0.451 0.222 1.539 0.026 0.013 0.373 0.375 0.144 3459 -0.637 0.055 0.077 1.707 0.861
4.000 UTXD 2.00 20 EQ 28 0.028 0.061 0.798 0.234 0.630 0.311 1.640 0.096 0.047 0.640 0.453 0.141 3379 -1.237 0.068 0.274 2.152 0.669
UTXF 3.00 20 EQ 28 0.028 0.061 0.998 0.293 0.869 0.428 1.722 0.287 0.142 0.990 0.533 0.139 3325 -2.114 0.085 0.823 2.900 0.469
UTXB 1.25 20 EQ 28 0.028 0.061 0.848 0.249 1.188 0.392 2.184 0.029 0.010 0.341 0.941 0.200 4784 -0.521 0.072 0.197 2.271 0.947
6.000 UTXD 2.00 20 EQ 28 0.028 0.061 0.998 0.293 1.590 0.525 2.328 0.108 0.036 0.606 1.233 0.212 5090 -1.055 0.085 0.702 2.627 0.839
UTXF 3.00 20 EQ 28 0.028 0.061 1.199 0.352 2.125 0.702 2.456 0.327 0.108 0.963 1.308 0.213 5094 -1.862 0.102 2.085 3.229 0.667
Dietrich UltraSTEEL® Track Section Properties 20 DW-Gauge EQMember Information Gross Section Properties Effective Properties Torsional Properties
Nominal Base Effective
Depth Designation Leg Gauge Mils Metal Metal Weight Area Ix Sx Rx Iy Sy Ry Ixe Sxe Mxa Xo J*1000 Cw Ro B
(in.) (in.) Thickness Thickness (lb./ft.) (in.2) (in.4) (in.3) (in.) (in.4) (in.3) (in.) (in.4) (in.3) (in.-lb.) (in.) (in.4) (in.6) (in.) Beta(in.) (in.)
UTEB 1.25 20 EQ 25 0.025 0.055 0.365 0.107 0.053 0.064 0.705 0.018 0.022 0.410 0.040 0.035 841 -0.881 0.025 0.009 1.201 0.462
1.625 UTED 2.00 20 EQ 25 0.025 0.055 0.500 0.147 0.080 0.096 0.740 0.064 0.076 0.661 0.048 0.038 903 -1.580 0.034 0.032 1.866 0.283
UTEF 3.00 20 EQ 25 0.025 0.055 0.679 0.199 0.116 0.139 0.763 0.191 0.228 0.979 0.055 0.039 945 -2.545 0.046 0.100 2.831 0.192
UTEB 1.25 20 EQ 25 0.025 0.055 0.444 0.130 0.137 0.108 1.026 0.021 0.016 0.399 0.106 0.065 1565 -0.770 0.030 0.023 1.344 0.671
2.500 UTED 2.00 20 EQ 25 0.025 0.055 0.578 0.170 0.200 0.157 1.086 0.074 0.058 0.660 0.128 0.069 1658 -1.431 0.039 0.084 1.914 0.441
UTEF 3.00 20 EQ 25 0.025 0.055 0.757 0.222 0.284 0.223 1.130 0.220 0.172 0.994 0.150 0.067 1609 -2.364 0.051 0.256 2.803 0.288
UTEB 1.25 20 EQ 25 0.025 0.055 0.544 0.160 0.320 0.174 1.414 0.023 0.013 0.380 0.259 0.104 2494 -0.666 0.037 0.055 1.608 0.828
3.625 UTED 2.00 20 EQ 25 0.025 0.055 0.679 0.199 0.451 0.245 1.504 0.083 0.045 0.647 0.312 0.102 2443 -1.281 0.046 0.195 2.079 0.620
UTEF 3.00 20 EQ 25 0.025 0.055 0.858 0.252 0.627 0.341 1.577 0.249 0.135 0.993 0.367 0.101 2408 -2.172 0.058 0.587 2.862 0.424
UTEB 1.25 20 EQ 25 0.025 0.055 0.578 0.170 0.402 0.198 1.539 0.024 0.012 0.373 0.330 0.114 2736 -0.638 0.039 0.069 1.707 0.860
4.000 UTED 2.00 20 EQ 25 0.025 0.055 0.712 0.209 0.562 0.277 1.639 0.086 0.042 0.641 0.397 0.113 2702 -1.239 0.048 0.245 2.152 0.669
UTEF 3.00 20 EQ 25 0.025 0.055 0.891 0.262 0.775 0.383 1.721 0.257 0.127 0.991 0.464 0.112 2675 -2.116 0.060 0.734 2.901 0.468
UTEB 1.25 20 EQ 25 0.025 0.055 0.757 0.222 1.060 0.350 2.183 0.026 0.009 0.341 0.800 0.163 3900 -0.522 0.051 0.177 2.271 0.947
6.000 UTED 2.00 20 EQ 25 0.025 0.055 0.891 0.262 1.419 0.469 2.327 0.096 0.032 0.607 0.999 0.171 4093 -1.056 0.060 0.627 2.627 0.838
UTEF 3.00 20 EQ 25 0.025 0.055 1.070 0.315 1.897 0.627 2.455 0.292 0.097 0.964 1.070 0.171 4103 -1.864 0.073 1.862 3.230 0.667
DMF07_034-035:DMF07_034-035 7/2/10 10:01 AM Page 35
Ultr
aSTE
EL®
Fire
and
Sou
nd A
ssem
blie
s
The place to stop…before the building starts! SM
Note: Deeper studs, batt and blanket insulation and resilient channel optional in all fire assemblies shown above.
2 Hour Assembly
• 3-5/8" Minimum Studs
• 2 Layers 5/8"National Type XApplied Vertically or Horizontally
2 Hour Assembly
• 2-1/2" Minimum Studs
• 2 Layers 5/8" USG Type XApplied Horizontally
2 Hour Assembly
• 1-5/8" Minimum Studs
• 2 Layers 5/8"Lafarge Type XApplied Vertically or Horizontally
— Fire AssembliesUnderwriters Laboratories V450 OptionsReference V450 listings for full assembly details.
2 Hour Assembly
• 1-5/8" Minimum Studs
• 2 Layers 5/8" CertainTeed Type XApplied Vertically or Horizontally
2 Hour Assembly
• 2-1/2" Minimum Studs
• 2 Layers 5/8"American Type XApplied Vertically or Horizontally
1 Hour Assembly
• 3-5/8" Minimum Studs
• 1 Layer 5/8" USG Type XApplied Vertically
1 Hour Assembly
• 3-5/8" Minimum Studs
• 1 Layer 5/8" USG Type XApplied Horizontally
1 Hour Assembly
• 3-5/8" Minimum Studs
• 1 Layer 5/8" USG Type CApplied Vertically
1 Hour Assembly
• 3-5/8" Minimum Studs
• 1 Layer 5/8" National Type XApplied Vertically
1 Hour Assembly
• 3-5/8" Minimum Studs
• 1 Layer 5/8" Lafarge Type XApplied Vertically
1 Hour Assembly
• 3-5/8" Minimum Studs
• 1 Layer 5/8" CertainTeed Type XApplied Vertically or Horizontally
1 Hour Assembly
• 3-5/8" Minimum Studs
• 1 Layer 5/8" American Type XApplied Vertically
request a quote online @
1 Hour Assembly
• 3-5/8" Minimum Studs
• 1 Layer 5/8" Georgia-Pacific Type DAPApplied Horizontally
2 Hour Assembly
• 1-5/8" Minimum Studs
• 2 Layers 5/8"Georgia-Pacific Type XApplied Vertically or Horizontally
36
09437 Assemblies Pages:DMF07_036-037 7/2/10 10:28 AM Page 36
Dietrich Design Group (North) ■
1414 Field Street, Building C, Suite 1Hammond, IN 46320800-873-2443 or 219-853-9474 phone219-932-4141 fax
Dietrich Design Group (South) ■
330 Greenwood PlaceMcDonough, GA 30253800-873-2443 or 678-304-5525 phone678-304-5556 fax
UltraSTEEL® Framing
STC 39 Assembly
• 3-5/8" Minimum Studs
• 1 Layer 5/8" Gypsum Board
STC 48 Assembly
• 3-5/8" Minimum Studs
• 3-5/8" Fiberglass Insulation
• 1 Layer 5/8" Gypsum Board
STC 52 Assembly
• 3-5/8" Minimum Studs
• 3-5/8" Fiberglass Insulation
• RC1 Channel 1 side
• 1 Layer 5/8" Gypsum Board
STC 61 Assembly
• 3-5/8" Minimum Studs
• 3-5/8" Fiberglass Insulation
• RC1 Channel 1 side
• Double Layer 5/8"Gypsum Board on Both Sides
— Sound AssembliesCertified by Riverbank Acoustical Laboratories.
For more information or to contact a sales representative, see page 3
— Fire Assemblies (continued)
1 Hour Assembly
• 2-1/2" Minimum Studs
• 1 Layer 1/2" American Type CApplied Vertically or Horizontally
• Batt and Blanket Required
1 Hour Assembly
• 2-1/2" Minimum Studs
• 1 Layer 1/2" Temple Inland Type CApplied Vertically or Horizontally
• Batt and Blanket Required
Note: Deeper studs and resilient channel optional in fire assemblies listed on this page.
— Certification Available in all 50 States
Dietrich Design Group (West) ■
2262 Rutherford RoadSuite 104Carlsbad, CA 92008800-873-2443 or760-931-0465 phone760-931-9824 fax
UltraSTEEL
®Fire and Sound Assem
blies
37
09437 Assemblies Pages:DMF07_036-037 7/2/10 10:28 AM Page 37
Inte
rior
(Dry
wal
l) N
onlo
ad-B
earin
g C
onto
ur T
rack
®
38
Punched WebsContour Track® is permanently locked into place by securing it to the primary supporting structure using the pre-punched holes conveniently placed throughout the web.
Expandable Ribbon TechnologyContour Track® flexible framing products feature expandable ribbon technology that expands and contours toyour desired curve, bend or radius. The ribbon technologyoffers curveable flexibility, while maintaining or holding itsshape during installation.
Dietrich Contour Track® flexible framing products are low-cost high performance framing solution for non-loadbearing curves, bends, variable radii and arches for dramaticand distinctive ceilings, walls and bulkheads. Today’s customers want more elaborate and complex contouredarchitecture including dramatic sweeping soffits and bulkheads, curved or rounded walls, wavy ceilings, barrelvaults, arched and contoured openings, round or ovalcolumns and elliptical and eyebrow curves.
DMF Thickness Size Weight PackagingProduct Gauge Mils Design Thickness Inches mm lbs/ft kg/m Pcs/SkidCode Inches mm
2 - 1/2 63.5 0.252 0.37 108CNTB 25 18 0.0188 0.48 3 - 5/8 92.1 0.310 0.46 108
6 152.4 0.431 0.64 1022 - 1/2 63.5 0.418 0.62 108
CNTB 20 DW 30 0.0312 0.79 3 - 5/8 92.1 0.514 0.76 1086 152.4 0.716 1.07 102
Use only in non-load bearing applications.
Contour Track® 1-1/4" Leg
Contour Track® is a low-cost, high-performance solutionfor creating non-load bearing intricate curves, bends,variable radii and arches for dramatic and distinctive walls, ceilings and bulkheads.■ Easily hand bends or forms to the
desired curve, bend, radius or arch
■ One product for both curves and arches
■ Use with wood or steel studs
■ Sizes: 2-1/2”, 3-5/8” and 6”
■ Gauges: 25 and 20
Dietrich Contour Track® joins the family of
available from Dietrich Metal Framing. This innovative family of high-performanceproducts have been developed to simplify installation, reduce materials and improvedproduct performance for backing, bracing, header and jamb framing, head-of-wall framing,deflection and rigid connections and now curved framing.
SAVINGLaborSolutionsTMSAVINGLaborSolutions TM
The place to stop…before the building starts! SMrequest a quote online @
DMF07_038-039:DMF07_038-039 7/2/10 10:02 AM Page 38
Interior Contour Track®Interior (D
rywall) N
onload-Bearing Contour Track
®
39
Hinged Support LegThe other leg of the DietrichContour Track® features pre-punched, easy-to-cut guideholes when contour track is used inarches or extreme radius conditionslike column framing. In these conditions, the ribbons are quicklyremoved with snips and the trimholes are partially cut to providemaximum flexibility and versatility.
Interlocking TrackContour Track® flexible framingmembers bend both ways and easily form challenging compoundcurves. S-curves are easily made byoverlapping and interlocking onetwo-inch web section. Screw attach,then hand bend to the desiredeffect.
UltraSTEEL® TechnologyDietrich Contour Track® featuresDietrich UltraSTEEL® framing technology. Unlike the smooth surface of other flexible track products, which tend to inhibit the“grabbing” of screws during installation, the “dimpled” surfaceof the CNTB actually helps to facilitate screw installation. The “dimpled” surface also makesthe product much safer to handle.
Dietrich UltraSTEEL® Framing:
■ Greatly reduced screwstripping
■ Virtually eliminates screwriding or walking
■ Stiffer, more rigidconstruction
■ Improved safety byreducing sharp edges and lips
It all adds up to:Faster, Easier and SaferInstallation
For more information or to contact a sales representative, see page 3
DMF07_038-039:DMF07_038-039 7/2/10 10:02 AM Page 39
Def
lect
ion
Trac
k Sy
stem
s
40 The place to stop…before the building starts! SMrequest a quote online @
Deflection products and sys-tems are used in wall assembliesthat are subjected to deflectionincluding seismic disturbances,foundation settling, and normalhead-of-wall compression.Deflection products allow forvertical movement while
maintaining wall integrity and fire protection.
A variety of deflection products can be used including:
■ SLP-TRK* Slotted Track
■ Long Leg (Deflection) Track with Spazzer®
Bridging Bar
■ Long Leg (Deflection) Track with U-Channeland EasyClip™ Connectors (U-Series™)
■ Double Track™ (Overtrack) System
■ Fast Top™ Clip with Long Leg (Deflection) Track
U.S. Patent # RE 39,462
SLP-TRK®
■ Eliminates high materialcost of custom-made headtracks
■ Requires only a singlegeneric Long Leg Track toaccommodate deflection
■ Facilitates sprayable intumescent/elastomericfirestops
■ Eliminates stud spacing layout at deck
■ Improves drywall hanging since bow is removedfrom tall studs
■ Automatically positions and rigidly holds studson 16” or 24” centerswithout fasteners in thehead trackU.S. Patent No. 5,784,850
*SLP-TRK is a registered trademark of SlipTrack Systems, Inc.** UL™ and UL Classified are trademarks of Underwriter’s Laboratories, Inc.
Long Leg (Deflection) Track withSpazzer® Bridging Bar
SLP-TRK* Slotted Track
■ Positive attachment that allows up to 1” of vertical movement
■ Meets ASTM, UL2079, IBC Building Codes
■ UL** Approved 1- and 2-hour systems
■ Single track assembly
Long Leg (Deflection) Track with U-Channel and EasyClip™ Connectors (U-Series™)
■ Nonproprietary system
■ Traditional framingcomponents
■ Requires U-Channel andEasyClip™ Connectors (U-Series™)
Interior (Drywall) Deflection Track Systems
■ Eliminates bridging at the top row of knockouts
■ Requires custom top track/longer lead times
Double Track™ (Overtrack) System
■ FastClip™ slip technology
■ Available in 3” and 5” widths
■ Attaches within the wall cavity
■ Proprietary screws provide frictionless slip connections
FastTop™ Connectors with Long Leg(Deflection) Track
A special benefit of the SLP-TRK® slotted track is that it attach-es directly to the under side of roof decks or floor/ceilingassemblies, eliminating the need for special cutting or shiplaps. Firestop caulking or spray applied fireproofing isrequired to achieve fire-rated performance.
SAVINGLabor
SolutionTM
SAVINGLabor
SolutionTM
DMF07_040-041:DMF07_040-041 7/2/10 10:04 AM Page 40
Interior (Drywall) Deflection Track Systems and Bridging OptionsBridging/Bracing O
ptions
41For more information or to contact a sales representative, see page 3
Lateral Bridging for Light-Gauge Steel Framed Walls (Interior Non-Axial Load Bearing)
U-Channel and EasyClip™ Connectors(U-Series™)
Bridging Recommendations
Block and Strap
Bridging and bracing of interior nonload-bearing framing can beachieved through various methods.
Three of the more common methods are:
■ Spazzer® 9200 Bridging and Spacing Bar
■ U-Channel and EasyClip™ Connectors (U-Series™)
■ Block and Strap
The purpose of bridging is to provide resistance to lateral andtorsional movement of the stud assembly. Bridging is normallyrequired when:
■ Wall sheathing does not extend to the undersideof the ceiling deck
■ Walls are only sheathed on one side
■ It is necessary to maintain the integrity of theframework during construction
■ To brace studs when using Long Leg (Deflection)Track
■ When required by certain fire-rated assemblies
■ Eliminates stud spacinglayout at deck
■ Improves drywallinstallation speed
■ Automatically positions and rigidly holds studs on 16” or 24” centers without fasteners
■ Eliminates clip angles and the labor required to install them
■ Prevents twisting andlateral movement
■ Traditional system
■ EasyClip™ Connectors (U-Series™) areprepunched for fasterinstallation
1. For an interior non-axial load-bearing wall with gypsum boardor other approved ASTM rigid facing material attached to bothstud flanges for the entire height of the wall, no bridging isrequired. However, temporary bracing of the wall is required ifone stud flange is temporarily unsheathed.
2. For an interior non-axial load-bearing wall with partial heightgypsum board, continuous bridging is required at 5-ft. maxi-mum vertical spacing above the elevation at which the boardis terminated.
3. For an interior non-axial load bearing wall with sheathingon one side only, bridging is required at 5-ft. maximum vertical spacing.
Note that for studs 6" wide and less in depth, bridging can be accomplished with the TradeReady™ Spazzer™ 9200 or 1-1/2" 16-gauge U-channel fastened to studs.
For a stud with a depth greater than 8" wide, block and strapbridging or solid blocking is required.
Spazzer® 9200 Bridging and Spacing Bar
■ Used as bridging whenframing members are unpunched
■ Eliminates the need for connectors
■ Provides alternativebridging when knockouts do not align
Interior (Drywall) Framing Products for Bridging/Bracing
DMF07_040-041:DMF07_040-041 7/2/10 10:04 AM Page 41
SLP-
TRK®
Slot
ted
Trac
k (B
DTK
)
It’s a real challenge meeting head-of-wall codes for fire stop and life safety while maintaining the ability to absorb verticalmovement in low-, mid- and high-rise buildings. SLP-TRK* slottedtrack is the solution.SLP-TRK® slotted track provides a positive attachment for wallstrength and allows for vertical movement. Movement caused by normal head-of-wall and floor extension or compression isabsorbed by SLP-TRK® slotted track to prevent damage to thewall assembly.SLP-TRK® slotted track systems comply with the toughest coderequirements in North America, if not the world. It’s been testedwith a variety of leading fire-stop products and has outperformedthe requirements of stringent fire and hose stream testing ASTME 119 and ASTM E 814. SLP-TRK also has met and exceeded the latest seismic cycling standards found in UL2079 and ASTM E 1966.
DMF Thickness Size*** Weight PackagingProduct Gauge Mils Design Thickness Inches mm lbs/ft kg/m Pcs/ Pcs/Code Inches mm Bundle Skid
2-1/2 63.5 0.484 0.718 1123-5/8 92.1 0.556 0.827 160
BDTK 25 18 0.0188 0.478 4 101.6 0.580 0.859 1446 152.4 0.708 1.050 968 203.2 0.836 1.240 80
2-1/2 63.5 0.882 1.309 1123-5/8 92.1 1.015 1.505 160
BDTK 20 33 0.0346 0.879 4 101.6 1.059 1.571 1446 152.4 1.294 1.922 968 203.2 1.529 2.270 80
2-1/2 63.5 1.150 1.706 1123-5/8 92.1 1.323 1.965 160
BDTK 18 43 0.0451 1.146 4 101.6 1.380 2.047 N/A 1446 152.4 1.687 2.503 968 203.2 1.993 2.959 80
2-1/2 63.5 1.443 2.142 1123-5/8 92.1 1.660 2.463 160
BDTK 16 54 0.0566 1.438 4 101.6 1.732 2.571 1446 152.4 2.117 3.142 968 203.2 2.502 3.713 80
2-1/2 63.5 1.818 2.699 1123-5/8 92.1 2.091 3.103 160
BDTK 14 68 0.0713 1.811 4 101.6 2.182 3.237 1446 152.4 2.667 3.959 968 203.2 3.152 4.677 80
*SLP-TRK is a registered trademark of SlipTrack Systems, Inc.**UL and UL Classified are trademarks of Underwriters Laboratories, Inc.***Custom sizes available upon request.
SLP-TRK® Slotted Track (BDTK)
Most cost-effective, positively attached fire-rated deflection system.
■ Positive attachment that allows up to 1” of vertical movement
■ Offers over 200 UL and ICC-ES Approved designs
■ UL** Approved 1- and 2-hour systems
■ Single track assembly
SLP-TRK®
Meeting Code RequirementsSLP-TRK® slotted track has achieved the following buildingcode approvals:• ICC-ES ESR 1042• UL Classified R19236• UL Certified for Canada XHL17• LA City RR25344• OSHPD R#0371• NY City MEA 285-01-M• National Building Code of Canada
U.S. Patent # RE 39,462
SAVINGLabor
SolutionTM
SAVINGLabor
SolutionTM
42 The place to stop…before the building starts! SMrequest a quote online @
DMF07_042-043:DMF07_042-043 7/2/10 10:05 AM Page 42
Interior (Drywall) Deflection Track SystemsLong Leg (D
eflection) Track (UT-Series
™) with Spazzer ®
9200 Bar (SPZD)
DMF SSMA Thickness Size Weight/Piece PackagingProduct Reference Gauge Mils Design Thickness Inches mm lbs kg Pcs./ Pcs./Code Inches mm Bundle Skid
SPZD NA 20 33 0.0346 0.8797/8 x 7/8 22.2 x 22.2
1.00 0.452 NA 1350x 50 x 1270
Spazzer® 9200 (SPZD)
Rapidly installed pre-notched, pre-spacedinterior deflection system that saves timeand eliminates materials.■ Eliminates high material cost of custom-made head tracks
■ Requires only a single generic Long Leg Track to provide deflection
■ Facilitates sprayable intumescent/elastomeric firestops
■ Eliminates stud spacing layout at deck
■ Improves drywall hanging since bow is removed from tall studs
■ Automatically positions and rigidly holds studs on 16” or 24” centres without fasteners in the head track
Long LegTrack
Spazzer™ 9200
SAVINGLabor
SolutionTM
SAVINGLabor
SolutionTM
Dietrich TradeReady® Spazzer® 9200 is a pre-notched, 20-gauge, galvanized steel spacer barengineered to handle deflection at the head track of interior nonload-bearing, nonstructural studwalls. The pre-notched slots and gripping power of the 50-inch bar holds studs into a rigid,accurately laid out gridwork that has excellent resistance to stud rotation and displacement.
The Spazzer® 9200 spacer bar saves time and materials by eliminating the cost of custom headtracks and the time required to fasten and remove screws or layout stud spacing at the deck.Hanging drywall is also faster and easier because the Spazzer® 9200 spacer bar eliminates thebow that often occurs in tall interior studs.
U.S. Patent No. 5,784,850
DMF Member Gauge Base Metal Effective Metal PackagingProduct Designation Equivalent Thickness Thickness Inches mm lbs/ft kg/m Pcs/ Pcs/Code Inches Inches Bundle SkidUTND 362 UTND 25EQ 0.015 0.035 3-5/8 92.1 0.388 0.577 N/A 1002" Leg 600 UTND 0.015 0.035 6 152.14 0.509 0.756 N/A 72UTED 362UTED 20 DW EQ 0.025 0.055 3-5/8 92.1 0.644 0.958 N/A 1002" Leg 600 UTED 0.025 0.055 6 152.14 0.846 1.259 N/A 72UTXD* 362 UTXD 20 STR EQ 0.028 0.061 3-5/8 92.1 0.760 1.131 N/A 1002" Leg 600 UTXD 0.028 0.061 6 152.14 0.998 1.485 N/A 72UTNF 362 UTNF 25EQ 0.015 0.035 3-5/8 92.1 0.49 0.729 N/A 1003" Leg 600 UTNF 0.015 0.035 6 152.4 0.611 0.909 N/A 72UTEF 362 UTEF 20 DW EQ 0.025 0.055 3-5/8 92.1 0.814 1.211 N/A 100
3" Leg 600 UTEF 0.025 0.055 6 152.4 1.016 1.512 N/A 72UTXF* 362UTXF 20 STR EQ 0.028 0.061 3-5/8 92.1 0.961 1.430 N/A 1003" Leg 600 UTXF 0.028 0.061 6 152.14 1.199 1.784 N/A 72
Custom sizes available upon request. *Available in limited markets
UltraSTEEL™ Long Leg (Deflection) Track (UT-Series™)
43For more information or to contact a sales representative, see page 3
DMF07_042-043:DMF07_042-043 7/2/10 10:05 AM Page 43
Long
Leg
(D
efle
ctio
n) T
rack
(U
T-Se
ries™
) w
ith U
-Cha
nnel
(CH
N-S
erie
s™),
Easy
Clip
™Cl
ip A
ngle
s (U
-Ser
ies™
)
44 The place to stop…before the building starts! SM
DMF SSMA Thickness Size Weight PackagingProduct Reference Gauge Mils Design Thickness Inches mm lbs/ft kg/m Pcs/ Pcs/Code Inches mm Bundle SkidCHN1 075U50-54 16 54 0.0566 1.438 3/4 19.1 0.25 0.371 10 350CHN2 150U50-54 16 54 0.0566 1.438 1-1/2 38.1 0.42 0.623 10 350
*Available in 10', 16' and 20' lengths.
U-Channel (CHN-Series™)
DMF SSMA Thickness Size Weight/Piece PackagingProduct Reference Gauge Mils Design Thickness Inches mm lbs kg Pcs./Code Inches mm BucketU543 NA 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 3-3/8 38.1 x 38.1 x 85.7 0.16 0.073 400U545 NA 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 5-3/4 38.1 x 38.1 x 146 0.28 0.127 200U547 NA 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 7-3/4 38.1 x 38.1 x 197 0.37 0.168 100
EasyClip™ Clip Angles (U-Series™)
EasyClip™ Clip Angle (U-Series™)
U-Channel
Traditional, single-track deflection system.■ Nonproprietary system
■ Traditional framing components
■ Requires U-Channel and EasyClip™ Clip Angles (U-Series™)
Long Leg Track
DMF Member Gauge Base Metal Effective Metal PackagingProduct Designation Equivalent Thickness Thickness Inches mm lbs/ft kg/m Pcs/ Pcs/Code Inches Inches Bundle SkidUTND 362 UTND 25EQ 0.015 0.035 3-5/8 92.1 0.388 0.577 N/A 1002" Leg 600 UTND 0.015 0.035 6 152.14 0.509 0.756 N/A 72UTED 362UTED 20 DW EQ 0.025 0.055 3-5/8 92.1 0.644 0.958 N/A 1002" Leg 600 UTED 0.025 0.055 6 152.14 0.846 1.259 N/A 72UTXD* 362 UTXD 20 STR EQ 0.028 0.061 3-5/8 92.1 0.760 1.131 N/A 1002" Leg 600 UTXD 0.028 0.061 6 152.14 0.998 1.485 N/A 72UTNF 362 UTNF 25EQ 0.015 0.035 3-5/8 92.1 0.49 0.729 N/A 1003" Leg 600 UTNF 0.015 0.035 6 152.4 0.611 0.909 N/A 72UTEF 362 UTEF 20 DW EQ 0.025 0.055 3-5/8 92.1 0.814 1.211 N/A 100
3" Leg 600 UTEF 0.025 0.055 6 152.4 1.016 1.512 N/A 72UTXF* 362UTXF 20 STR EQ 0.028 0.061 3-5/8 92.1 0.961 1.430 N/A 1003" Leg 600 UTXF 0.028 0.061 6 152.14 1.199 1.784 N/A 72
Custom sizes available upon request. *Available in limited markets
UltraSTEEL™ Long Leg (Deflection) Track (UT-Series™)
This traditional assemblyallows for the deflection offloor beams or floor decksabove interior partitions. The single, long leg trackassembly requires 1-1/2" cold-rolled channel (CHN2)and 1-1/2" x 1-1/2" 16-gauge EasyClip™ Clip Angles (U-Series™), installedcontinuously throughout the upper most punchouts
(must be a maximum of 12" from the top track), to align the studs vertically within the plane of the wall.
request a quote online @
DMF07_044-045:DMF07_044-045 7/2/10 10:07 AM Page 44
Interior (Drywall) Deflection Track SystemsD
oubleTrack™
(Overtrack) System
(OT-Series
™/UT-Series
™)
45For more information or to contact a sales representative, see page 3
Traditional, double track or track-over-track system.■ Eliminates bridging at the top row of knockouts
■ Requires custom top track/longer lead times
Dietrich DoubleTrack™ system is a two-piece top trackassembly that allows for the deflection of floor beams orfloor decks along interior partitions. A custom-made longleg outer track is installed to the underside of the floordeck. A wall assembly is constructed on the floor then slidinto place. The wall assembly is designed to allow a “gap”at the top for deflection.
DMF SSMA Thickness Size WeightProduct Reference Gauge Mils Design Thickness Inches mm lbs/ft kg/mCode Inches mmOTSB 375T125-33
20 30 0.0312 0.7923-3/4 95.3 0.758 1.125
1-1/4" Leg 612T125-33 6-1/8 155.6 1.027 1.525OTSC 375T200-33
20 30 0.0312 0.7923-3/4 95.3 0.871 1.292
2" Leg 612T200-33 6-1/8 155.6 1.140 1.692OTSE 375T300-33
20 30 0.0312 0.7923-3/4 95.3 1.098 1.630
3" Leg 612T300-33 6-1/8 155.6 1.367 2.030Custom sizes available on request.
DoubleTrack™ (Overtrack) System (OT-Series™/TR-Series™)
DoubleTrack™ (Overtrack)
Long Leg Track
DMF Member Gauge Base Metal Effective Metal PackagingProduct Designation Equivalent Thickness Thickness Inches mm lbs/ft kg/m Pcs/ Pcs/Code Inches Inches Bundle SkidUTND 362 UTND 25 EQ 0.015 0.034 3-5/8 92.1 0.388 0.577 N/A 1202" Leg 600 UTND 0.015 0.034 6 152.4 0.509 0.756 N/A 70UTED 362 UTED 20 EQ 0.025 0.055 3-5/8 92.1 0.644 0.958 N/A 1202" Leg 600 UTED 0.025 0.055 6 152.4 0.846 1.259 N/A 70UTNF 362 UTNF 25 EQ 0.015 0.034 3-5/8 92.1 0.490 0.729 N/A 1003" Leg 600 UTNF 0.015 0.034 6 152.4 0.611 0.909 N/A 52UTEF 362 UTEF 20 EQ 0.025 0.055 3-5/8 92.1 0.814 1.211 N/A 100
3" Leg 600 UTEF 0.025 0.055 6 152.4 1.016 1.512 N/A 52Custom sizes available upon request.
*SLP-TRK is a trademark of SlipTrack Systems, Inc.
UltraSTEEL® Long Leg (Deflection) Track (UT-Series™)
DMF07_044-045:DMF07_044-045 7/2/10 10:07 AM Page 45
Spaz
zer®
9200
Brid
ging
and
Spa
cing
Bar
(SP
ZD)
46 The place to stop…before the building starts! SMrequest a quote online @
The TradeReady® Spazzer® 9200 bar is a pre-notched, 20-gauge,galvanized steel spacer and bridging bar. The Spazzer® 9200 barfacilitates rapid erection of studs into a rigid, accurately laid outgridwork that has excellent resistance to stud rotation anddisplacement. Hanging drywall is also faster and easier becausethe Spazzer® 9200 bareliminates the bowthat often occurs in tallinterior studs.
TradeReady® Spazzer®
9200 bar is a 20-gaugebar that is 50" long andpre-notched to holdstuds rigidly on 16" or24" centers. The slotshave been pre-engineered to holdstuds in place byutilizing “shear” to bridge studs into a rigid gridwork.
U.S. Patent Nos. 5,784,850 and 6,021,618
DMF Thickness Size Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm lbs kg Pcs/ Pcs/Code Inches mm Bundle Skid
SPZD 20 33 0.0346 0.8797/8 x 7/8 22.2 x 22.2
1.00 0.452 NA 1350x 50 x 1270
Spazzer® 9200 Bridging and Spacing Bar (SPZD)
Save up to 40% in combinedlabor and materials costs!■ Eliminates stud spacing layout at deck
■ Improves drywall installation speed
■ Automatically positions and rigidly holds studs on 16” or 24” centers without fasteners
■ Eliminates clip angles and the labour required to install them
Spazzer ® 9200
OvernightDelivery!
Available for
SAVINGLabor
SolutionTM
SAVINGLabor
SolutionTM
DMF07_046-047:DMF07_046-047 7/2/10 10:08 AM Page 46
Interior (Drywall) Framing Products for Bridging/BracingU
-Channel (C
HN
-Series™) and EasyC
lip™
Clip Angles (U
-Series™)
47For more information or to contact a sales representative, see page 3
DMF CSSBI Thickness Size Weight PackagingProduct Reference Gauge Mils Design Thickness Inches mm lbs/ft kg/m Pcs/ Pcs/Code Inches mm Bundle SkidCHN1 075U50-54 16 54 0.0566 1.438 3/4 19.1 0.25 0.361 10 350CHN2 150U50-54 16 54 0.0566 1.438 1-1/2 38.1 0.42 0.623 10 350
*Available in 10', 16' and 20' lengths.
U-Channel (CHN-Series™)
DMF Thickness Size Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm lbs kg Pcs/Code Inches mm BucketU543 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 3-3/8 38.1 x 38.1 x 85.7 0.16 0.073 400U545 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 5-3/4 38.1 x 38.1 x 146 0.28 0.127 200U547 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 7-3/4 38.1 x 38.1 x 197 0.37 0.168 100
EasyClip™ Clip Angles (U-Series™)
Traditional bridging system that provides rigidity and lateral support to the constructed framework.■ Prevents twisting and lateral movement
■ Traditional system
■ EasyClip™ Clip Angles (U-Series™) are prepunched for faster installation
Dietrich U-Channel is available in 16-gauge corrosion-resistant galvanized steel. The product is available in threewidths of 3/4", and 1-1/2". For bridging, 1-1/2" and 3/4" areutilized with the 1-1/2" channel as the predominant sizeused in bracing applications. Standard lengths are 10', 16'and 20'. Custom lengths are available on request.
To brace steel studslaterally, the channel isinserted through thepunched knockouts ofthe framing members atspecified verticalspacing. An EasyClip™
Clip Angle (U-Series™) isthen screw attached toboth the U-Channel andthe framing member.The U-Channel must besecured with clips toprovide resistance andproper bracing.
U-Channel
EasyClip™ Clip Angle (U-Series™)
DMF07_046-047:DMF07_046-047 7/2/10 10:08 AM Page 47
Furri
ng C
hann
el (
FC-S
erie
s™)
U-C
hann
el (
CHN
-Ser
ies™
) H
ange
r W
ire/T
ie W
ire a
nd F
urrin
g Ch
anne
l Clip
s (M
FCC)
48 The place to stop…before the building starts! SMrequest a quote online @
Rigid structural support for gypsum wallboard, veneerplaster or drop ceilingassemblies.■ Commonly used in noncombustible ceiling assembly
■ Rigid framework for high-quality finish
■ Furring channel clips easily snap into place for fastassembly
In a ceiling assembly U-Channel is suspended from theoverhead structure using hanger wire. Drywall furringchannel is commonly clipped or wire-tied perpendicular tothe underside of the U-Channel at appropriate intervals forscrew-attaching drywall. Assemblies are installed per theproject specification or ASTM C 754 requirements.
Furring channel canalso be attacheddirectly to theunderside of bar joists.The furring is installedperpendicular to thejoists and wire-tied atappropriate intervals.Wire ties are requiredfor fire-rated and multilayer assemblies.
DMF SSMA Thickness Size Weight PackagingProduct Reference Gauge Mils Design Thickness Inches mm lbs/ft kg/m Pcs/ Pcs/Code Inches mm Bundle SkidFCN 087F125-18 25 18 0.0188 0.478 0.237 0.351 10 600FCE 087F125-30 20 30 0.0312 0.792
7/8 22.20.388 0.577 NA 600
FCM 087F125-43 18 43 0.0451 1.146 0.555 0.823 NA 250FCM 087F125-54 16 54 0.0566 1.438 0.670 0.994 NA 250FCND 150F125-18 25 18 0.0188 0.478 0.312 0.462 NA 500FCED 150F125-30 20 30 0.0312 0.792
1-1/2 38.10.512 0.761 NA 500
FCMD 150F125-43 18 43 0.0451 1.146 0.733 1.088 NA 250FCMD 150F125-54 16 54 0.0566 1.438 0.920 1.364 NA 250
Furring Channel (FC-Series™)
DMF SSMA Thickness Size Weight PackagingProduct Reference Gauge Mils Design Thickness Inches mm lbs/ft kg/m Pcs/ Pcs/Code Inches mm Bundle SkidCHN1 075U50-54 16 54 0.0566 1.438 3/4 19.1 0.285 0.423 10 350CHN2 150U50-54 16 54 0.0566 1.438 1-1/2 38.1 0.424 0.630 10 350
*Available in 10', 16' and 20' lengths.
U-Channel (CHN-Series™)
Furring Channel
Furring Channel ClipHanger Wire
Tie Wire
U-Channel
DMF07_048-049:DMF07_048-049 7/2/10 10:13 AM Page 48
Interior (Drywall) Framing Products for Ceiling ApplicationsFurring Channel (FC-Series
™) U-Channel (CH
N-Series
™) Hanger W
ire/Tie Wire and Furring Channel Clips (M
FCC)
49
DMF Length Weight/Bundle PackagingProduct Gauge ft m lbs kg Bundles/Code SkidHWB8 8 12 3.66 50 22.62 20HWB9 9 12 3.66 50 22.62 20HW12 12 12 3.66 50 22.62 20
Hanger Wire (HWB8, HWB9, HW12)
DMF Length Weight/BoxProduct Gauge Inches mm lbs kgCode
24 610 25 11.31TW18 18 28 711 25 11.31
48 1219 50 22.62
Tie Wire (TW18)
DMF Pcs./ Weight/BoxProduct Box lbs kgCodeMFCC 500 20 9.05
Furring Channel Clips (MFCC)Furring Channel Clip
Hanger Wire
Tie Wire
OvernightDelivery!
Available for
For more information or to contact a sales representative, see page 3
DMF07_048-049:DMF07_048-049 7/2/10 10:13 AM Page 49
Cor
ner
Angl
e (C
A-Se
ries™
) C
orne
r An
gle
(HC
N)
and
120˚
/135
˚ (C
AEW
)
50 The place to stop…before the building starts! SMrequest a quote online @
Corner angle is a multipurpose 90˚ or 120 /̊135˚galvanized angle used in dozens of framing applications.Some of the most common applications include lappedframing conditions, soffit framing, floor and ceiling runner,chase wall construction and laminated gypsum drywallpartitions.
SplayedCorner Angle(120º/135º)
Utility angles used to connect, reinforceor secure metal stud framing in variousdrywall applications.■ Available in numerous sizes and gauges
■ Custom sizes, bends and lengths availableCorner Angle
(90º)
DMF Thickness Size Length Weight PackagingProduct Gauge Mils Design Thickness Inches mm ft m lbs/ft kg/m Pcs/Code Inches mm Skid
5/8 x 2 15.9 x 50.8 0.150 0.223 5007/8 x 1-3/8 22.2 x 34.9 0.160 0.236 500
CAN 90˚ 25 18 0.0188 0.478 1-1/2 x 1-1/2 38.1 x 38.1 10 3.05 0.170 0.252 5002 x 2 50.8 x 50.8 0.290 0.430 5003 x 3 76.2 x 76.2 0.430 0.640 500
CANW 135˚ 25 18 0.0188 0.4781-1/2 x 1-1/2 38.1 x 38.1
10 3.050.170 0.252 500
2 x 2 50.8 x 50.8 0.250 0.371 500HCN (Hemmed) 90˚ 25 18 0.0188 0.478 2 x 2 50.8 x 50.8 10 3.05 0.270 0.400 500
5/8" x 2 15.9 x 50.8 0.300 0.446 5007/8 x 1-3/8 22.2 x 34.9 0.260 0.387 500
CAE 90˚ 20 30 0.0312 0.792 1-1/2 x 1-1/2 38.1 x 38.1 10 3.05 0.330 0.489 5002 x 2 50.8 x 50.8 0.450 0.669 5003 x 3 76.2 x 76.2 0.680 1.010 500
CAEW 135˚ 20 30 0.0312 0.7921-1/2 x 1-1/2 38.1 x 38.1
10 3.050.370 0.548 500
2 x 2 50.8 x 50.8 0.500 0.741 500Packaging may vary by region.
Corner Angle (CA-Series™), Corner Angle (HCN) and 120˚/135˚ (CAEW)
DMF07_050-051:DMF07_050-051 7/2/10 10:14 AM Page 50
Interior (Drywall) Framing Products for Various Drywall Framing AssembliesFurring C
hannel (FC-Series
™) for Walls and C
eilings
51For more information or to contact a sales representative, see page 3
■ Provides noncombustible furring for interiorand exterior walls
■ Use to level uneven surfaces
■ Available in 7/8” and 1-1/2” depths and 25, 20, 18 and 16 gauge
■ Standard lengths are 10’ and 12’. Other lengths available
Dietrich furring channel is a hat-shaped corrosion-resistantframing component used to furr out masonry walls andceiling assemblies. In concrete wall applications, furringchannel is installed vertically to the wall surface usingconcrete nails or power-driven fasteners. Gypsum panelsare then screw-attached to the furring channels. In ceilingapplications, furring channels can be attached directly tothe underside of the buildingstructure using tie wire, screws orpower-driven fasteners. Heavier-gauge furring enables greater spansand loading capacity. 18- or 16-gauge furring is commonly usedfor purlins in exterior applications.
DMF SSMA Thickness Size Weight PackagingProduct Reference Gauge Mils Design Thickness Inches mm lbs/ft kg/m Pcs/ Pcs/Code Inches mm Bundle SkidFCN 087F125-18 25 18 0.0188 0.478 0.237 0.351 10 600FCE 087F125-30 20 30 0.0312 0.792
7/8 22.20.388 0.577 10 600
FCM 087F125-43 18 43 0.0451 1.146 0.555 0.823 NA 250FCM 087F125-54 16 54 0.0566 1.438 0.670 0.994 NA 250FCND 150F125-18 25 18 0.0188 0.478 0.312 0.462 NA 500FCED 150F125-30 20 30 0.0312 0.792
1-1/2 38.10.512 0.761 NA 500
FCMD 150F125-43 18 43 0.0451 1.146 0.733 1.089 NA 250FCMD 150F125-54 16 54 0.0566 1.438 0.920 1.364 NA 250
*Hemmed leg furring channel (as shown) is only available in 25 gauge.
Furring Channel (FC-Series™) for Walls and Ceilings
Economical hat-shaped framingcomponent used to “furr” outceilings and masonry walls.
7/8" FurringChannel*
1-1/2" FurringChannel*
DMF07_050-051:DMF07_050-051 7/2/10 10:14 AM Page 51
Resi
lient
Cha
nnel
s (R
C-S
erie
s™)
for
Wal
ls a
nd C
eilin
gs
Dietrich resilient channel is one of the most efficient low-cost methods developed to reduce transmission ofairborne sound through partition and ceiling assemblies.The resilient channel dampens sound waves effectively,dissipating the energy and reducing sound transmission bysuspending gypsum wallboard 1/2" from the stud or joist.Sound absorption can be maximized by utilizing soundattenuation blankets within the wall or floor cavity.
Resilient channel is manufactured from 25- and 20-gauge corrosion-resistant galvanized steel and is available withsingle or double legs. The single leg resilient channel isavailable in regular (RCUR) and deluxe (RCSD) sizes.Dietrich high-performance single leg resilient channel(RCUR) has a 1-1/4" screw flange. The RCUR is commonlyused in wall applications. Dietrich™ RC Deluxe™ resilientchannel (RCSD) is the preferred resilient channel in manyapplications because of its extra-wide 1-1/2" screw flange.The extra-wide flange provides added rigidity and a widersurface for faster and easier installation of sheathingmaterials.
Dietrich double leg resilient channel (RCDN/RCDE) has two legs for rapid installation. Double leg resilientinstallation is typically used for ceiling applications withmultiple layers of gypsum board. Double leg resilient iseasier to install, but offers a lower STC rating.
DMF Thickness Size Length Weight PackagingProduct Gauge Mils Design Thickness Inches mm ft m lbs/ft kg/m Pcs/ Pcs/Code Inches mm Bundle SkidRCUR 25 18 0.0188 0.478 1-1/4 31.8 12 3.66 0.160 0.236 20 1020RCUR 20 30 0.0312 0.792 1-1/4 31.8 12 3.66 0.280 0.416 20 500RCSD 25 21 0.0221 0.561 1-1/2 38.1 12 3.66 0.220 0.328 20 1000RCDN 25 18 0.0188 0.478 1-1/4 31.8 12 3.66 0.210 0.312 20 1020RCDE 20 30 0.0312 0.792 1-1/4 31.8 12 3.66 0.400 0.594 20 500
Resilient Channel (RC-Series™), Walls and Ceilings
One of the most efficient low-costmethods of reducing soundtransmission in wood or steel-framed partition or ceiling assemblies.■ Lab-certified STC-rated up to 61
■ Single and double leg channels
■ RC Deluxe™ (RCSD) has extra-wide screwsurface for easy attachment
■ Available in 12’ lengths
RCUR
RC Deluxe™
RCSD–STC Rating up to 61
Double Leg ResilientRCDN/RCDE
52 The place to stop…before the building starts! SMrequest a quote online @
DMF07_052-053:DMF07_052-053 7/2/10 10:15 AM Page 52
Interior (Drywall) Framing Products for Various Drywall Framing AssembliesResilient C
hannels (RC-Series
™) for Walls and C
eilings
53For more information or to contact a sales representative, see page 3
DMF07_052-053:DMF07_052-053 7/2/10 10:15 AM Page 53
Dan
back
®W
ood
Back
ing
Plat
e
Stud
Shear Load
Normal Load
DMF Width Length Weight/Piece PackagingProductCode*
in mm in mm lbs kg Pcs/Skid
D16F 5-1/8 130 48 1219 5.114 2.319 250D24F 5-1/8 130 48 1219 5.114 2.319 250
*F = fire-treated plywood. D16 = 16" O.C. spacing. D24 = 24" O.C. spacing. Trimables available for off-module spacing in small bucket or bulk quantities.
U.S. Patent Number 6,705,056 and other Patents Pending Danback® is a registered trademark of Daniel W. Tollenaar Dricon® is a registered trademark of Arch Wood Protection, Inc.
Cabinets, Shelves,Counters, Sinks,
Handrails, Chalkboards, Towel & Shower Bars,
or anything that requiresheavy-duty backing!
The Perfect Backing Solution for:
Product Specifications and Packaging
JUST SNAP, FLEX and SCREWReduce steel stud backing installation time up to 90%. It’s that fast!
Features and Benefits
■ Reduces installation time up to 90%
■ Available for 16" and 24" O.C. framing
■ Eliminates cutting, notching, ripping and routing
■ Made with Dricon®
fire-retardant treated wood
■ Complies with all national building codes
■ EPA registered protection againsttermites and fungal decay
■ No greater corrosion rates than untreated wood
Commonly Used in:
Hospitals, Medical Centers, Schools,
Hotels/Motels, Assisted Living, Condominiums, or any project that requires heavy-duty backing!
Ultimate Load ValueDMF
Shear Load Norm. LoadProductMax. lbs Max. lbsCode
D16F 814 516D24F 725 418
NOTES: Listed load values are maximum test load values. Designers must apply design safety factorsappropriate for intended use.Tabulated loads do notinclude the contribution of gypsum board or other wall sheathing.
54 The place to stop…before the building starts! SMrequest a quote online @
SAVINGLabour
SolutionTM
SAVINGLabour
SolutionTM
DMF07_054-055:DMF07_054-055 7/2/10 10:16 AM Page 54
Interior (Drywall) Framing Products for Various Drywall Framing Assemblies
Snap “Starter Edge” into theopen side of the stud flange.
HINT: Start with the first full bay.Use Danback® Trimables for off-module bays.
Flex Danback® Flexible WoodBacking around stud flange usingthe flexible connector plate.
Repeat the process. Overlap connector plates whenusing in long backing runs.
Cut to required length. Secure connector plate tothe trimmed edge, Leave 1-1⁄4 " extended over thetrimmed edge. Fasten the plate to Danback using3 small pan or wafer head screws.
Secure each plate to the stud flange using2 small pan or wafer head screws.
UseDanback™
Trimables foroff-modulebays.
Just Snap, Flex and Screw. Reduces backing installation time up to 90%. It’s that fast.
Backing steel studs has always been a difficult, costly and time-consuming job.The Danback® Flexible Wood Backing System, featuring Dricon® fire-retardanttreated wood, has made wood backing installation easy and economical.
Danback® is a heavy-duty flexible wood backing system used to support cabinets,shelves, handrails, wall-mounted sinks and counters and all other wall-mountedfixtures. Danback provides superior connection shear and pullout strength tosupport and meet even some of the heaviest loading conditions. Simply snap,flex and screw Danback™ into place. The patented hinge design actually flexesaround the stud and snaps into place for a perfect fit—every time.
Danback® is constructed using Dricon® fire-retardant treated wood (FRT).Dricon® FRT is pressure-treated wood that is chemically treated to reduce theflamespread and smoke development. Dricon® is a Class A fire retardant, that isEPA registered, NER approved (NER-303) and complies with all national codesincluding the 2003 International Building Code (IBC) and the 2003 InternationalResidential Code Council (ICC).
Danback® Trimables foroff-module backing. Connector Plates
included withTrimables.
AWPA C20/C27AWPA P17 (FR-1)FR-SNER-303 (BOCA, ICBO, SBCCI)EPA Registration (62190-9) UL Building Materials DirectoryUL Recognized Component NYC MEA 199-81-MNYC MEA 200-81-M
Factory Mutual Class I Roof DeckCity of Los Angeles (RR 25122)FHA Minimum Property Standard #2600HUD Materials Release (1261)California State Fire MarshalState of WisconsinQPL
All are subject to revision, reexamination.
Dricon® FRT Wood complies with or has been granted the following:
Dricon® is a registered trademark of Arch Wood Protection, Inc.
Danback
®W
ood Backing Plate
55
DMF07_054-055:DMF07_054-055 7/2/10 10:17 AM Page 55
Z-Fu
rring
(ZF
-Ser
ies™
)
56 The place to stop…before the building starts! SMrequest a quote online @
DMF Thickness Size Length Weight PackagingProduct Gauge Mils Design Thickness Inches mm ft m lbs/ft kg/m Pcs/ Pcs/Code Inches mm Bundle SkidZFN1 18 0.0188 0.478 1" 25.4 0.200 0.295 NA 500ZFN2
2518 0.0188 0.478 1-1/2" 38.1 0.240 0.357 NA 500
ZFN3 18 0.0188 0.478 2" 50.88'-6", 2.59,
0.270 0.400 NA 500ZFN4 18 0.0188 0.478 2-1/2" 63.5
10', 3.05,0.300 0.446 NA 500
ZFE1 30 0.0312 0.792 1" 25.412' 3.66
0.310 0.459 NA 500ZFE2
2030 0.0312 0.792 1-1/2" 38.1 0.360 0.535 NA 500
ZFE3 30 0.0312 0.792 2" 50.8 0.420 0.623 NA 500ZFE4 30 0.0312 0.792 2-1/2" 63.5 0.480 0.712 NA 500
Heavier gauges available on request.
Z-Furring (ZF-Series™)
Dietrich Z-furring is used to furr out interior masonry orpoured concrete wall substrates and to support rigidpolystyrene, mineral, or fiberglass batt insulation whileproviding a uniform plane for gypsum panel attachment. Z-furring should be installed vertically with the 3/4" flangeagainst the substrate. The type of fastener and spacing willvary based on application. Gypsum wallboard may be installedparallel or perpendicular to the Z-furring. Metal lath shouldbe installed perpendicular to the Z-furring.
Easily accommodates rigid insulationand provides for the attachment ofgypsum wallboard, veneer or plaster to the interior of masonry walls.■ 1-1/4” wide flange for easy screw attachment
■ ”Toed in” leg to grip rigid insulation positively
■ Available in 1”, 1-1/2”, 2”, 2-1/2” depths and 10’ standard length
■ Custom sizes and lengths available
Z-Furring
DMF07_056-057:DMF07_056-057 7/2/10 10:44 AM Page 56
Interior (Drywall) Framing Products for Various Drywall Framing AssembliesBacking Plate (B
P)
57For more information or to contact a sales representative, see page 3
Added support whereshelves, cabinets, fixturesor handrails are installed.■ Use as backer plates for attachment
of fixtures to metal stud walls
■ Available in 2”, 3”, 4”, 6”, 8”, 10” and 12”widths and 25- and 20-gauge
■ Standard length is 10’. Other lengths and coil stock are available
Dietrich backing plate is ageneral multipurpose flat stockthat is used for backer plate tosupport shelves, cabinets,fixtures or handrails whenapplied to metal framing.Backing plate should not beused as tension strapping orcross bracing. Diagonal TensionStrapping (DTN) should be usedin those applications.
DMF Thickness Size Length Weight PackagingProduct Gauge Mils Design Thickness Inches mm ft m lbs/ft kg/m Pcs/Code Inches mm Skid
2 50.8 10 3.05 0.129 0.190 2003 76.2 10 3.05 0.194 0.289 2004 101.6 10 3.05 0.258 0.384 200
BPN 25 18 0.0188 0.478 6 152.4 10 3.05 0.387 0.574 2008 203.2 10 3.05 0.516 0.767 20010 254.0 10 3.05 0.645 0.958 20012 304.8 10 3.05 0.774 1.148 2002 50.8 10 3.05 0.214 0.318 2003 76.2 10 3.05 0.321 0.476 2004 101.6 10 3.05 0.428 0.636 200
BPE 20 30 0.0312 0.792 6 152.4 10 3.05 0.642 0.954 2008 203.2 10 3.05 0.857 1.273 20010 254.0 10 3.05 1.071 1.591 20012 304.8 10 3.05 1.285 1.906 200
Backing Plate (BP)
Backing Plate
DMF07_056-057:DMF07_056-057 7/2/10 10:44 AM Page 57
Gro
mm
ets
(GRO
M)
58 The place to stop…before the building starts! SMrequest a quote online @
■ Snaps quickly into stud knockout
■ Prevents/eliminates pipe rattle
■ Standard grommets fit all size studs except 1-5/8" and 2-1/2"
■ Use the Snap-In bushing for 1-5/8" and 2-1/2" wall framing
■ Grommets are packaged 100 pieces per bag or in boxes of 500
DMF SizeProduct Inches mm Description Pcs/BagCode
GROM3/4 19.1 3/4" for 1-5/8" and 2-1/2" Studs 100
1-1/2 38.1 1-1/2" for 3-1/2" and Wider Studs 100
Grommets (GROM)
Grommets snap easily into stud knockouts and are used toprotect electrical wiring and plumbing lines from contactingmetal. Grommets are commonly used in construction whenmetal conduit is not required by building code.
InstallationInstall grommets in all stud knockouts where wiring andplumbing lines will be inserted. Use the Snap-in bushing for 1-5/8" and 2-1/2" wall studs and the standard 2-piece grommetfor all wall studs 3-1/2" and wider.
For 1-5/8" and 2-1/2" Studs For 3-1/2" and Wider
Snap-In Bushing
Grommets protect andisolate electrical wiringand plumbing fromcontacting metal.
Install the Snap-In bushing by pressing the bushing into the stud knockout. Make sure to engage the bushing lips to secure into place.
Install the standard 2-piece grommet by first opening the grommet asillustrated above. Insert one side of the grommet through the knockout.Snap the grommet together so it engages with the metal sandwichedbetween the two plastic sides.
2-PieceGrommet
DMF07_058:DMF07_058 7/2/10 10:17 AM Page 58
Exterior Light-GaugeConnections/Accessories for Rigid ConnectionsUni-Clip™ (UCEC) ..............................98EasyClip™ E-Series™
Support Clips ....................................99EasyClip™ S-Series™
Support Clips ..................................100EasyClip™ U-Series™
Support Clips ..................................101EasyClip™ B-Series™
Support Clips ..................................102EasyClip™ X-Series™
Support Clips ..................................103EasyClip™ A-Series™
End Clips ..........................................104Simpson™ Holdowns (HD Series)....105Simpson™ Tension Ties (HT14) ........105Exterior Light-Gauge FramingAccessories for Bridging andBracingSpazzer® 5400 (SPZS) and Spazzer® Snap-in Grommet (SPGR)Spazzer® Bar Guard (SPBG)........106U-Channel (CHN) and EasyClip™ Clip Angles (U-Series™) ........................................107U-Channel (CHN) and Welding ............................................108Block (TSB) and Strap (DT Series™) ......................................109Diagonal Tension Strapping/Shear Wall Bracing (DT)/Gusset Plates (GP) for Shear Wall Bracing ........110–111Exterior Light-Gauge FramingAccessories for Various FramingApplicationsCorner Angle (CAM)......................112Heavy-Duty Furring Channel (FCM) ................................................113Custom Shapes and MiscellaneousAngles (VS) ......................................114
Long Leg Deflection Track (TS-Series™) System with U-Channel (CHN), EasyClip™ Clip Angles (U-Series™), and Screws..........68–69DoubleTrack™ (Overtrack) Systems (OT-Series™) ................................70–71Headers, Jambs, PostsHDS® Framing System..............72–85ProX Header®
Framing System ........................86–87Exterior Light-Gauge Load-Bearing Wall HeadersL-Header (LHDR)..............................88TradeReady® (TDHA/TDHB) Load-Bearing Header ......................89C-Stud Headers (Available in component pieces only) ........90–91
Back-to-Back (C-Studs) (TS-Track™) (S-Series Clips™)......90
Boxed Header (C Studs) (TS-Track™) (S-Series Clips™)......91
Capped Header (C-Studs) (TS-Track™) (S-Series Clips™)......91
Exterior Light-GaugeConnections/Accessories for Deflection/Slip ConnectionsFast Clip™ (FCSC) ..............................92Fast Strut™ (FS12/FS15)..................93Fast Top® Clip (FTC3/FTC5) ..........94Slide Clip (SD2S)..............................95Slide Clip (SD) ..................................96QuickClip™ (QC-Series™) ..................97
Exterior Light-Gauge SteelFraming Systems for Curtain-Wall/Axial Load-BearingC-Studs (C-Series™) ..................62–63Knockouts/Knockout Pattern ......64Track (TS-Series™)..............................65Exterior Light-Gauge SteelDeflection SystemsSLP-TRK® Slotted Track System(BDTK)..........................................66–67Long Leg (Deflection) Track (TS-Series™) System with Spazzer®
Bridging Bar (SPZS) and Spazzer®
Bar Guard Retaining Clip (SPBG)..................................................68–69
59
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:04 AM Page 59
The place to stop…before the building starts! SM
Exterior Light-Gauge SteelFraming Systems for Curtain-Wall/Axial Load-Bearing
Exterior light-gauge steel framing is used in avariety of applications including axial load-bear-ing and curtain-wall construction.
Axial load-bearing members are used in wall androof truss framing. They are designed to carry both lat-eral and axial loads. Axial framing members provide pri-
mary structural support and have been used as the primary framing system up to nine stories.
Curtain-wall framing members are used in exterior walls to provide an envelope oroutside skin on the building. Light-gauge steel framing members provide exterior envelope (curtain-wall) framing for a variety of construction and finishing systems. Theyare ideal back-up support assemblies for brick-veneer, stucco and E.I.F.S. systems.Dietrich™ curtain-wall framing members are utilized for in-fill, bypass (balloon) and span-drel framing applications. Dietrich’s wide variety of products allow engineers to select aneconomical system to meet any design criteria, including high wind and seismic loads.
Exterior Light-Gauge SteelDeflection Systems
Deflection products and systems are used in both inte-rior and exterior wall assemblies in areas that are sub-jected to movement, including seismic disturbances.Deflection products allow for vertical movement, anddepending on the head-of-wall detail, can also providefor concomitant fire protection.
A variety of deflection products can be used including:
■ SLP-TRK* Slotted Track
■ Long-Leg (Deflection) Track with Spazzer® 5400 Bridging Bar
■ Long-Leg Track with U-Channel and EasyClip™ Clip Angles (U-Series™)
■ Double-Track (Overtrack) System
Exterior Light-Gauge Load-Bearing Wall Headers
Load-bearing headers are structural components or assemblies that carry and redistributeloads over door, window or other wall, floor or roof openings. Headers can be field assem-bled using conventional C-Stud and track members, or specialty headers like the L-Headerand TradeReady® Header can be custom-ordered to fit your specific framing conditions.
The most common header configurations are:
■ L-Header
■ TradeReady® Load-Bearing Header
■ Back to Back (I-Header)
■ Boxed Header
Consideration should be given to specialty headers as they substantially reduce laborand materials. These products tend to be lighter in weight and most are easily insulat-ed after installation, unlike conventional C-Stud box headers that must be insulatedduring fabrication.
Exte
rior
Fram
ing
Ove
rvie
w
60 request a quote online @
*SLP-TRK is a registered trademarkof Sliptrack Systems, Inc.
EXTERIORFRAMINGOVERVIEW
Exterior light gauge framing is used ina variety of construction applicationsincluding axial load-bearing walls,floors, roofs and curtain-wall assem-blies in low-rise, mid-rise, high-rise,educational, institutional, multi-familyand multi-use commercial and resi-dential structures. Light-gauge framingproducts can be assembled to provideversatile, cost-effective, lightweight andnoncombustible assemblies used as pri-mary or secondary framing systems.When used as the primary frame, steelframing assemblies have been used upto nine stories. When used as a second-ary frame with heavy structural steel orconcrete structures, light-gauge fram-ing provides low-cost, efficient framingthat can accommodate almost any fac-ing material. Light-gauge steel framingis commonly stick framed; however, it ishighly suited for prefabricated panelconstruction that provides additionaleconomy in today’s highly competitiveconstruction industry.
Light-gauge steel framing is a superiorbuilding material. Its high strength-to-weight ratio maximizes building designflexibility and provides rigid structuralintegrity. Light-gauge steel framing iseasily insulated for high-energy conser-vation and provides noncombustiblesupport for fire-rated construction.
Dietrich Metal Framing offers the mostcomprehensive and widest selection offraming products, systems and servicesavailable in the industry. This wideselection of products, gauges, yieldstrengths, sizes and flange widthsenables the designer to obtain optimalperformance at economical costs.
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:04 AM Page 60
61For more information or to contact a sales representative, see page 3
Overview
Exterior Light-GaugeConnections/Accessories forDeflection/SlipConnections
Deflection or slip con-nections are designed topermit movement of
curtain-wall framing that results from thermal expansion andcontraction, building movement or other forces. DietrichMetal Framing offers a variety of specialized clips to meet justabout every deflection condition. This wide selection of clipsgives the designer the ability to attain optimal performanceat the most economical costs.
Dietrich Metal Framing provides one of the widest selectionsof deflection and slip connections available. This exteriorline provides a wide array of options to meet just aboutevery deflection condition. Choose from the high-perform-ance Fast Clip™ for typical deflection conditions, or choose aFast Strut™ for standoff conditions.
Many of the deflection clips feature Fast Clip™ technology.These clips are embossed with fastening patterns to ensureaccurate placement of fasteners. Proprietary screws are alsoprovided with each clip to ensure friction-free sliding.
If you are uncertain and would like assistance in selectingthe right clip for your deflection condition, contact our tech-nical service group at 800-873-2443.
Exterior Light-GaugeConnections/Accessoriesfor RigidConnectionsRigid connection clipsand supports are usedin a variety of ways to
secure light-gauge framing members to each other or to thebuilding structure. Some of the more common rigid con-nections include joist connections, curtain-wall connections,opening connections, beam/wall connections, bridging con-nections and header connections.
Dietrich Metal Framing provides one of the widest selectionsof rigid connection clips available. This extensive line pro-vides a wide array of options to meet most rigid connectionapplications. Choose from our wide variety of support andattachment clips, specialty hold downs and tension ties.Most of these support and specialty clips are prepunched forfast and accurate fastener placement.
Exterior Light-GaugeFramingAccessories for Bridgingand Bracing
Bridging and bracing ofstructural walls is requiredto provide resistance to
stud rotation and minor axis bending under wind and axial loads.Bridging and bracing of structural framing can be achievedthrough various methods.
Some of the most common methods are:
■ TradeReady® Spazzer® 5400 Bridging Bar
■ U-Channel Attached with EasyClip™
Clip Angles (U-Series™)
■ U-Channel Welded to Framing Members
■ Block and Strap
Dietrich Metal Framing provides a wide selection of bridgingand bracing products to meet just about every condition orpreferred installation method. The Spazzer® 5400 bridging barrepresents the latest in bridging technology. The Spazzer®
bridging bar is manufactured with proprietary pre-punchedslots that reduce installation costs and provides excellent tor-sional and lateral stud restraint.
Exterior Light-GaugeFramingAccessories forVariousFramingApplications
Dietrich Metal Framingoffers a variety of heavy-gauge framing components for vari-ous load-bearing or structural framing conditions. Theseproducts include heavy-duty corner angles, furring channelsand a wide assortment of custom-fabricated shapes andcomponents.
Utilizing state-of-the art manufacturing equipment, Dietrichcan fabricate a large array of shapes, clips, bends, angles,long-leg tracks and miscellaneous closures.
Exterior Framing O
verview
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:04 AM Page 61
62
C-S
tuds
(C
-Ser
ies™
)
Dietrich C-Studs are light-weight, cold-formed galvanizedsteel members used in axial load-bearing walls, curtain-walls, floorjoists and roof truss framing. C-Studs are available in a widearray of sizes, flanges, gauges andyield strengths to obtain optimalperformance at minimal costs.
One of the key differencesbetween the various C-Stud/ Joist framing members is the flange and returndimensions. The flange istypically the bearing surface forcladding materials and a keycontributor to the load-bearingcapacity of the member. Flange sizes include 1-1/4", 1-3/8", 1-5/8", 2", 2-1/2" and 3".
Dietrich CWI™ light-duty curtain-wallstuds have a 1-1/4" flange and 1/4" returnand are used to support the exterior skinin ultra-light applications. CWI studs areavailable only in the Pacific Northwest.
Dietrich CWN™ curtain-wall studs have a1-3/8" flange and 3/8" return and are usedto support the exterior skin or claddingmaterial (metal, stone, tile, glass, etc.) and the wind loads to which they aresubjected.
Dietrich CSJ™ studs/joist have a 1-5/8" flange and a 1/2"return and are considered the industry standard. CSJmembers are the most widely used and specified framingmembers. They provide the vertical strength necessary for demanding load-bearing structural applications and sufficient strength for many joist applications.
Dietrich CSW™ wide studs/joist have a 2" wide flange and a 5/8" return that provides a larger bearing surface forattaching sub-flooring or sheathing materials. This framingmember is also used in axial load-bearing wall assemblies.
Dietrich CSE™ extra-wide studs/joist have a 2-1/2" wideflange and a 5/8" return and are used in floor joistassemblies and heavy loading conditions.
Dietrich CSS™ super-wide studs/joist have a 3" flange and a 1" return and are used in very heavy loading andlong spanning conditions.
Light-gauge C-shaped framing members foraxial load-bearing walls, curtain-walls,tall interior partitions, floor joists and roof truss assemblies.■ Size (Web): 2-1/2”, 3-1/2”, 3-5/8”, 4”, 5-1/2”, 6”,
8”, 10”, 12”, 14”.
■ Flange Sizes: 1-1/4”, 1-3/8”, 1-5/8”, 2”, 2-1/2”, 3”.
■ Gauges: 20 (33 mils), 18 (43 mils), 16 (54 mils), 14 (68 mils) and 12 (97 mils).
■ 20 and 18-gauge are standard as 33 ksi yieldstrength. 16, 14, 12-gauge are standard as 50ksi yield strength.
■ Custom sizes, lengths and coatings available.
C-Stud
The place to stop…before the building starts! SMrequest a quote online @
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:05 AM Page 62
For more information or to contact a sales representative, see page 3
Exterior Light-Gauge Steel Framing Systems for Curtain-Wall/Axial Load-BearingC
-Studs (C-Series
™)
DMF SSMA Thickness Depth Flange ReturnProduct Reference Gauge (mils) Inches mm Inches mm Inches mmCode*
250S125-x 2-1/2 63.5 1-1/4 31.8 1/4 6.4CWI3 (20 & 18 gauge) 362S125-x 20 (33), 18 (43), 3-5/8 92.1 1-1/4 31.8 1/4 6.4CWI5 (16 & 14 gauge) 600S125-x 16 (54), 14 (68) 6 152.4 1-1/4 31.8 1/4 6.4
800S125-x 8 203.2 1-1/4 31.8 1/4 6.4250S137-x 2-1/2 63.5 1-3/8 34.9 3/8 9.5
CWN3 (20 & 18 gauge)362S137-x
20 (33), 18 (43),3-5/8 92.1 1-3/8 34.9 3/8 9.5
CWN5 (16 & 14 gauge)400S137-x
16 (54), 14 (68)4 101.6 1-3/8 34.9 3/8 9.5
600S137-x 6 152.4 1-3/8 34.9 3/8 9.5800S137-x 8 203.2 1-3/8 34.9 3/8 9.5250S162-x 2-1/2 63.5 1-5/8 41.3 1/2 12.7350S162-x 3-1/2 88.9 1-5/8 41.3 1/2 12.7362S162-x 3-5/8 92.1 1-5/8 41.3 1/2 12.7400S162-x 4 101.6 1-5/8 41.3 1/2 12.7
CSJ3 (20 & 18 gauge) 550S162-x 20 (33), 18 (43), 5-1/2 149.7 1-5/8 41.3 1/2 12.7CSJ5 (16, 14 & 12 gauge) 600S162-x 16 (54), 14(68), 12 (97) 6 152.4 1-5/8 41.3 1/2 12.7
800S162-x 8 203.2 1-5/8 41.3 1/2 12.71000S162-x 10 254.0 1-5/8 41.3 1/2 12.71200S162-x 12 304.8 1-5/8 41.3 1/2 12.71400S162-x 14 355.6 1-5/8 41.3 1/2 12.7362S200-x 3-5/8 92.1 2 50.8 5/8 15.9400S200-x 4 101.6 2 50.8 5/8 15.9
CSW3 (20 & 18 gauge)600S200-x
20 (33), 18 (43),6 152.4 2 50.8 5/8 15.9
CSW5 (16, 14 & 12 gauge)800S200-x
16 (54), 14(68), 12 (97)8 203.2 2 50.8 5/8 15.9
1000S200-x 10 254.0 2 50.8 5/8 15.91200S200-x 12 304.8 2 50.8 5/8 15.91400S200-x 14 355.6 2 50.8 5/8 15.9362S250-x 3-5/8 92.1 2-1/2 63.5 5/8 15.9400S250-x 4 101.6 2-1/2 63.5 5/8 15.9
CSE3 (20 & 18 gauge)600S250-x
20 (33), 18 (43),6 152.4 2-1/2 63.5 5/8 15.9
CSE5 (16, 14 & 12 gauge)800S250-x
16 (54), 14(68), 12 (97)8 203.2 2-1/2 63.5 5/8 15.9
1000S250-x 10 254.0 2-1/2 63.5 5/8 15.91200S250-x 12 304.8 2-1/2 63.5 5/8 15.91400S250-x 14 355.6 2-1/2 63.5 5/8 15.9600S300-x 6 152.4 3 76.2 1 25.4
CSS3 (18 gauge)800S300-x
18 (43),8 203.2 3 76.2 1 25.4
CSS5 (16, 14 & 12 gauge)1000S300-x
16 (54), 14 (68), 12 (97)10 254.0 3 76.2 1 25.4
1200S300-x 12 304.8 3 76.2 1 25.41400S300-x 14 355.6 3 76.2 1 25.4
*20 and 18-gauge are standard as 33 ksi yield strength. 16, 14, 12-gauge are standard as 50 ksi yield strength.*CWI available in limited geographical areasX= mil thickness identifier
C-Studs (C-Series™)
NOTE: This catalog does not provide load data (load capacities, limiting heights,physical and structural properties and span data) necessary for building design.Assistance is available at www.dietrichmetalframing.com or by calling Dietrich Design Group at 800-873-2443.
63
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:05 AM Page 63
64 The place to stop…before the building starts! SMrequest a quote online @
Knoc
kout
s/Kn
ocko
ut P
atte
rn
Dietrich light-gauge C-studs for axial load-bearing and curtain-wall framing areprepunched with knockouts at regularintervals. These punchouts are specificallydesigned to allow for rapid installation ofpipes, electrical conduit and wall bridging.
Standard knockout sizing is 1-1/2" x 4" in members 3-1/2" and wider. Memberssmaller than 3-1/2" are unpunched unlessotherwise specified at time of order. Ifspecified, members will be punched with a 3/4" x 4" knockout.
Knockouts are punched 12" from the leadedge with additional knockouts every 24"O.C. (on the WestCoast the firstknockout is punched24" from the leadedge). Caution mustbe exercised wheninstalling studs soknockouts align forbridging. Based onstud length, thedistance the knockoutfalls from the tail endof the stud may not bethe same from the leadend. To align punch-outs, make sure to usethe same end in thesame directionconsistently.
Conveniently placed holes for easy installation of wiring,plumbing and bridging.■ Prepunched at regular intervals.
■ Easily accommodates Spazzer® or U-Channel bridging.
■ Custom hole placement available on request.
East andCentralPunch
Patttern
West CoastPunch Pattern
Varies
2'
2'
2'
2'
2'
2'
2'
2'
Varies
1'
2-1/2" widestuds
3-1/2" andwider
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:05 AM Page 64
65For more information or to contact a sales representative, see page 3
Exterior Light-Gauge Steel Framing Systems for Curtain-Wall/Axial Load-BearingTrack (TS-Series
™)
Dietrich structural track is a U-shaped framing componentused as top and bottom runnersto secure wall studs. Structuraltrack is also used as end supportclosures for joists at exterior orfoundation walls, head and sillplates of wall openings and solidblocking. Track is normallyordered in corresponding sizeand gauge to the wall studs.Longer leg track is used fordeflection conditions or toaccommodate uneven orinconsistent floor or ceilingconditions. Slip track for track-over-track assemblies is alsoavailable.
DMF SSMA Thickness Leg HeightProduct Reference Gauge (mils) Inches mmCode
TSA x-T100-y20 (33), 18 (43), 16 (54),
1 25.414 (68), 12 (97)
TSB x-T125-y20 (33), 18 (43), 16 (54),
1-1/4 31.814 (68), 12 (97)
TSF x-T150-y20 (33), 18 (43), 16 (54),
1-1/2 38.114 (68), 12 (97)
TSC x-T200-y20 (33), 18 (43), 16 (54),
2 50.814 (68), 12 (97)
TSE x-T300-y20 (33), 18 (43), 16 (54),
3 76.214 (68), 12 (97)
OTSF z-T150-y20 (33), 18 (43), 16 (54),
1-1/2 38.114 (68), 12 (97)
OTSC z-T200-y20 (33), 18 (43), 16 (54),
2 50.814 (68), 12 (97)
OTSE z-T300-y20 (33), 18 (43), 16 (54),
3 76.214 (68), 12 (97)
Track (TS-Series™)
x = Part depth. Tracks are available to match all stud and joist depths.y = mil thickness of steel.z = Part depth. Overtracks are available in all standard stud depths. The track width
is sized to fit over a standard TS series track.
U-shaped channel runners used as the top and bottom tracks to securewall studs or end support closures forfloor joist framing.■ Sizes (Web): 2-1/2”, 3-1/2”, 3-5/8” 4”, 5-1/2”,
6”, 8”, 10”, 12”, 14”.
■ Leg heights: 1”, 1-1/4”, 1-1/2”, 2” and 3”.
■ Gauges: 20 (33 mils), 18 (43 mils), 16 (54 mils), 14 (68 mils) and 12 (97 mils).
■ 20 and 18-gauge are standard as 33 ksi yieldstrength. 16, 14, 12-gauge are standard as 50 ksi yield strength.
■ Standard 10’ lengths.
■ Custom sizes, lengths and coatings available.
Track
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:05 AM Page 65
66 The place to stop…before the building starts! SMrequest a quote online @
SLP-
TRK®
Slot
ted
Trac
k Sy
stem
(B
DTK
)
It’s a real challenge these days meeting head-of-wall codesfor fire stop and life safety issues while maintaining theability to absorb vertical movement in low-, mid- and high-rise buildings. SLP-TRK* slotted track is the solution.
SLP-TRK® slotted track provides a positive attachment foroverall strength and allows for vertical movement causedby normal head-of-wall and floor extension orcompression. SLP-TRK® slotted track smoothly integrateswith a variety of wall installation systems and is extremelyuser-friendly as well as economical. The simple design andeasy installation reduces the cost of materials and labor.And the installer can use the head-of-wall systems heprefers to work with.
SLP-TRK® slotted track systems comply with the toughestcode requirements in North America, if not the world. Ithas been tested with a variety of leading fire-stop productsand has outperformed the requirements of stringent fireand hose stream testing of ASTM E 119 and ASTM E 814.SLP-TRK has also met and exceeded the latest seismiccycling standards found in UL2079 and ASTM E 1966.
The SLP-TRK® slotted track has achieved the followingbuilding code approvals:
ICC-ES ESR 1042UL Classified R19236UL Certified for Canada XHL17LA City RR25344OSHPD R#0371NY City MEA 285-01-M
SLP-TRK® slotted track is installed directly to the slab orcorrugated metal roof deck using #10 sheet metal screws,Tapcon** concrete screws or power-driven fasteners.Fasteners must be placed at 8" or 12" intervals dependingon the flute intervals of the metal decking material. Studsmust be cut 3/4" shorter than floor-to-ceiling height toallow for ceiling deflection. Studs are attached to the trackthrough the midpoint of flange slots using #8 self-tappingwafer-head screws on each side of the stud.
U.S. Patent # RE 39,462
Most cost-effective, positively attached fire-rated deflection system.■ Positive attachment that allows up to 1” of vertical movement.
■ UL*** approved 1- and 2-hour systems.
■ Meets IBC, BOCA, SBCCI, ASTM, UL2079, and UBC building codes and standards.
■ Single track assembly.
SLP-TRK®
*SLP-TRK is a registered trademark of SlipTrack Systems, Inc.;**Tapcon is a registered trademark of Illinois Tool Works Inc.;***UL and UL Classified are trademarks of Underwriters Laboratories, Inc.
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:05 AM Page 66
67For more information or to contact a sales representative, see page 3
Exterior Light-Gauge Steel Deflection SystemsSLP-TRK
®Slotted Track System
(BD
TK)
U.S. Patent # RE 39,462
DMF Thickness Size Weight PackagingProduct Gauge Mils Design Thickness Inches mm lbs/ft kg/m Pcs/ Pcs/Code Inches mm Bundle Skid
2-1/2 63.5 0.484 0.718 1123-5/8 92.1 0.556 0.826 100
BDTK 25 18 0.0188 0.478 4 101.6 0.580 0.859 906 152.4 0.708 1.050 608 203.2 0.836 1.240 50
2-1/2 63.5 0.882 1.309 1123-5/8 92.1 1.015 1.505 100
BDTK 20 33 0.0346 0.879 4 101.6 1.059 1.571 906 152.4 1.294 1.922 608 203.2 1.529 2.270 50
2-1/2 63.5 1.150 1.706 1123-5/8 92.1 1.323 1.965 100
BDTK 18 43 0.0451 1.146 4 101.6 1.380 2.047 N/A 906 152.4 1.687 2.503 608 203.2 1.993 2.958 50
2-1/2 63.5 1.443 2.142 1123-5/8 92.1 1.660 2.463 100
BDTK 16 54 0.0566 1.438 4 101.6 1.732 2.571 906 152.4 2.117 3.142 608 203.2 2.502 3.713 50
2-1/2 63.5 1.818 2.699 1123-5/8 92.1 2.091 3.103 100
BDTK 14 68 0.0713 1.811 4 101.6 2.182 3.237 906 152.4 2.667 3.959 608 203.2 3.152 4.677 50
*Custom sizes are available on request.**SLP-TRK is a registered trademark of SlipTrack Systems, Inc.
SLP-TRK** (BDTK)
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:05 AM Page 67
68 The place to stop…before the building starts! SMrequest a quote online @
Long
Leg
Def
lect
ion
Trac
k (T
S-Se
ries™
)
Traditional, single-trackdeflection assembly forcurtain-wall framing.■ Nonproprietary system.
■ Traditional framing components.
■ Requires U-Channel and clip angles.
The TradeReady® Spazzer®
5400 prenotched, 16-gauge,galvanized steel spacer andbridging bar is engineered tofacilitate the rapid erection ofexterior deflection wall framing.Before the Spazzer® 5400Bridging Bar, deflection at thehead track was addressed witha variety of systems includingdouble track, proprietary
tracks, deep leg track with cold rolled channel, clip angles orwelds, solid blocks and metal strap across the face of the studsor by fastening the studs to the top track and removing thescrews prior to installing the wall sheathing.
The prenotched slots and gripping power of the 50-inch
TS-Series™ System with U-Channel (CHN), EasyClip™ Clip Angles (U-Series™) and Screws
Enhance productivity and reduce materials with the Spazzer® 5400‚prenotched, prespaced exterior deflection assembly.■ Eliminates high material cost of custom-made head tracks.
■ Requires only a single generic Long Leg Track to provide deflection.
■ Facilitates sprayable intumescent/elastomeric firestops.
■ Eliminates stud spacing layout at deck.
■ Automatically positions and holds studs rigidly on 12”, 16” or 24” spacing.
This traditional assembly accommodates the deflection of floor beams or floor decks at the head of wall. The single long leg track assembly requires 1-1/2" cold-rolledchannel (CHN) and 1-1/2" x 1-1/2" 16-gauge EasyClip™ Clip Angles (U-Series™) installedcontinuously throughout the uppermost punch-outs to align the studs vertically within the plane of the wall. Deflection track details must be designed for the specificconditions of a building to accommodate the required deflection and end reactions ofthe studs. Deflection tracks cannot be used in axial load-bearing stud conditions orabove continuous window spandrels.
Long LegTrack
U-ChannelEasyClip™ Clip Angle
(U-Series™)
Screw
TS-Series™ System with Spazzer® Bridging Bar (SPZS) and Spazzer® Bar Guard™ Retaining Clip (SPBG)
Spazzer® 5400 bridging bar assembles steel studs into a rigid, accurate gridwork that allows for deflection and provides excellent resistance to stud rotation and displacement without the use of mechanical attachments and welding equipment. The Spazzer®
Bar Guard™ retaining clip, or screws must be installed in curtain-wall and axial load-bearing wall applications to prevent the Spazzer® 5400 bridging bar from accidentally being disengaged.
U.S. Patent No. 6, 708, 60 and other Patents Pending
Spazzer®
5400
Spazzer® BarGuard™
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:05 AM Page 68
69For more information or to contact a sales representative, see page 3
Exterior Light-Gauge Steel Deflection SystemsLong Leg (D
eflection) Track (TS Series™)
DMF SSMA Thickness Size Weight PackagingProduct Reference Gauge Mils Design Thickness Inches mm lbs./ft. kg/m Pcs./ Pcs./Code Inches mm Bundle SkidCHN2 150U50-54 16 54 0.0566 1.438 1-1/2 38.1 0.420 0.623 10 330
*Available in 10', 16' and 20' lengths.
U-Channel (CHN)
DMF SSMA Thickness Size Weight/Piece PackagingProduct Reference Gauge Mils Design Thickness Inches mm lbs. kg Pcs./Code Inches mm BucketU543 NA 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 3-3/8 38.1 x 38.1 x 85.7 0.16 0.073 400U545 NA 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 5-3/4 38.1 x 38.1 x 146 0.28 0.127 200U547 NA 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 7-3/4 38.1 x 38.1 x 197 0.37 0.168 100
EasyClip™ Clip Angles (U-Series™)
DMF SSMA Thickness Size Weight PackagingProduct Reference Gauge Mils Design Thickness Inches mm lbs./ft. kg/m Pcs./ Pcs./Code Inches mm Bundle Skid
TSC362T200-33
20 33 0.0346 0.8793-5/8 92.1 0.863 1.282 NA 220
600T200-33 6 152.4 1.132 1.683 NA 120
TSC362T200-43
18 43 0.0451 1.1463-5/8 92.1 1.122 1.669 NA 220
600T200-43 6 152.4 1.473 2.191 NA 120
TSC362T200-54
16 54 0.0566 1.4383-5/8 92.1 1.410 2.099 NA 220
600T200-54 6 152.4 1.851 2.755 NA 120
TSC362T200-68
14 68 0.0713 1.8113-5/8 92.1 1.774 2.640 NA 220
600T200-68 6 152.4 2.328 3.464 NA 120
TSC362T200-97
12 97 0.1017 2.5833-5/8 92.1 2.528 3.762 NA 220
600T200-97 6 152.4 3.318 4.936 NA 120
TSE362T300-33
20 33 0.0346 0.8793-5/8 92.1 1.090 1.620 NA 154
600T300-33 6 152.4 1.359 2.020 NA 84
TSE362T300-43
18 43 0.0451 1.1463-5/8 92.1 1.417 2.109 NA 154
600T300-43 6 152.4 1.767 2.627 NA 84
TSE362T300-54
16 54 0.0566 1.4383-5/8 92.1 1.781 2.650 NA 154
600T300-54 6 152.4 2.221 3.303 NA 84
TSE362T300-68
14 68 0.0713 1.8113-5/8 92.1 2.240 3.332 NA 154
600T300-68 6 152.4 2.794 4.156 NA 84
TSE362T300-97
12 97 0.1017 2.5833-5/8 92.1 3.193 4.749 NA 154
600T300-97 6 152.4 3.984 5.927 NA 84*Custom sizes available on request.
Long Leg (Deflection) Track (TS-Series™)
DMF SSMA Thickness Size Weight/Piece PackagingProduct Reference Gauge Mils Design Thickness Inches mm lbs. kg Pcs./ Pcs./Code Inches mm Bundle Skid
SPZS NA 16 54 0.0566 1.4381-1/4 x 31.8 x 31.8
2.06 0.932 NA 6801-1/4 x 50 x 1270
Spazzer™ 5400 Bar (SPZS)
DMF SSMA Size Weight/Piece PackagingProduct Reference Inches mm lbs. kg Pcs./Code BoxSPBG NA 3-1/4" x 1-5/8" 82.5 x 41.3 0.05 0.02 100
Spazzer™ Bar Guard™ Retaining Clip (SPBG)
U.S. Patent No. 6, 708, 460 and other Patents Pending
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:05 AM Page 69
70
Dou
bleT
rack
™(O
vertr
ack)
Sys
tem
s (O
T-Se
ries™
)
A DoubleTrack™ system is a two-piece assembly thataccommodates deflection of exterior curtain walls. Acustom-made deep leg outer track is installed to theunderside of the floor deck. A wall assembly is constructedon the floor and slid into place. The wall assembly is builtto allow a “gap” at the top for deflection.
The track-over-track assembly, although still used, isbecoming less and less common. The development ofinnovative deflection systems like the SLP-TRK* System(page 66) has significantly improved and streamlined the assembly process. DoubleTrack™ deflection assembliescannot be used in axial load-bearing stud conditions orabove continuous window spandrels.
Traditional, DoubleTrack™ ortrack-over-track curtain-walldeflection system.■ Eliminates bridging.
■ Requires custom top track and longer lead times.
DoubleTrack™
Long Leg Track
*SLP-TRK is a registered trademark of SlipTrack Systems, Inc.
The place to stop…before the building starts! SMrequest a quote online @
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:05 AM Page 70
For more information or to contact a sales representative, see page 3
Exterior Light-Gauge Steel Deflection SystemsD
oubleTrack™
(Overtrack) System
s (OT-Series
™)
DMF SSMA Thickness Size Weight PackagingProduct Reference Gauge Mils Design Thickness Inches mm lbs/ft kg/m Pcs/ Pcs/Code Inches mm Bundle Skid
OTSC375T200-33
20 33 0.0346 0.8793-3/4 95.3 0.871 1.296 NA 220
612T200-33 6-1/8 155.6 1.140 1.696 NA 120
OTSC375T200-43
18 43 0.0451 1.1463-3/4 95.3 1.131 1.683 NA 220
612T200-43 6-1/8 155.6 1.481 2.204 NA 120
OTSC387T200-54
16 54 0.0566 1.4383-7/8 98.4 1.441 2.145 NA 220
625T200-54 6-1/4 158.8 1.881 2.798 NA 120
OTSC387T200-68
14 68 0.0713 1.8113-7/8 98.4 1.808 2.690 NA 220
625T200-68 6-1/4 158.8 2.361 3.513 NA 120
OTSC387T200-97
12 97 0.1017 2.5833-7/8 98.4 2.570 3.824 NA 220
625T200-97 6-1/4 158.8 3.360 4.999 NA 120
OTSE375T300-33
20 33 0.0346 0.8793-3/4 95.3 1.098 1.633 NA 154
612T300-33 6-1/8 155.6 1.367 2.034 NA 84
OTSE375T300-43
18 43 0.0451 1.1463-3/4 95.3 1.425 2.119 NA 154
612T300-43 6-1/8 155.6 1.775 2.640 NA 84
OTSE387T300-54
16 54 0.0566 1.4383-7/8 98.4 1.811 2.693 NA 154
625T300-54 6-1/4 158.8 2.251 3.349 NA 84
OTSE387T300-68
14 68 0.0713 1.8113-7/8 98.4 2.272 3.382 NA 154
625T300-68 6-1/4 158.8 2.826 4.205 NA 84
OTSE387T300-97
12 97 0.1017 2.5833-7/8 98.4 3.232 4.808 NA 154
625T300-97 6-1/4 158.8 4.022 5.983 NA 84
*Custom sizes available on request.C=2" LegsE=3" Legs
DoubleTrack™ (Overtrack) System (OT-Series™/TS-Series™)
DMF SSMA Thickness Size Weight PackagingProduct Reference Gauge Mils Design Thickness Inches mm lbs/ft kg/m Pcs/ Pcs/Code Inches mm Bundle Skid
TSC362T200-33
20 33 0.0346 0.8793-5/8 92.1 0.863 1.282 NA 220
600T200-33 6 152.4 1.132 1.683 NA 120
TSC362T200-43
18 43 0.0451 1.1463-5/8 92.1 1.122 1.669 NA 220
600T200-43 6 152.4 1.473 2.191 NA 120
TSC362T200-54
16 54 0.0566 1.4383-5/8 92.1 1.410 2.099 NA 220
600T200-54 6 152.4 1.851 2.755 NA 120
TSC362T200-68
14 68 0.0713 1.8113-5/8 92.1 1.774 2.640 NA 220
600T200-68 6 152.4 2.328 3.464 NA 120
TSC362T200-97
12 97 0.1017 2.5833-5/8 92.1 2.528 3.762 NA 220
600T200-97 6 152.4 3.318 4.936 NA 120
TSE362T300-33
20 33 0.0346 0.8793-5/8 92.1 1.090 1.620 NA 154
600T300-33 6 152.4 1.359 2.020 NA 84
TSE362T300-43
18 43 0.0451 1.1463-5/8 92.1 1.417 2.109 NA 154
600T300-43 6 152.4 1.767 2.627 NA 84
TSE362T300-54
16 54 0.0566 1.4383-5/8 92.1 1.781 2.650 NA 154
600T300-54 6 152.4 2.221 3.303 NA 84
TSE362T300-68
14 68 0.0713 1.8113-5/8 92.1 2.240 3.332 NA 154
600T300-68 6 152.4 2.794 4.156 NA 84
TSE362T300-97
12 97 0.1017 2.5833-5/8 92.1 3.193 4.749 NA 154
600T300-97 6 152.4 3.984 5.927 NA 84
*Custom sizes available on request.C=2" LegsE=3" Legs
Long Leg (Deflection) Track (TS-Series™)
71
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:05 AM Page 71
72 The place to stop…before the building starts! SMrequest a quote online @
Benefits
■ Outstanding bending strength in two directions.
■ Reduces installation time by 50%.
■ Eliminates box beam header assembly.
■ Reduces material and labor costs up to 50%.
■ HDS® can be screw-attached from either side.
■ Eliminates stud-to-track nesting for post, headerand jamb studs.
■ Openings up to 15' wide.
■ Eliminates multimember built-up truss chordsand webs.
■ Eliminates excessive bridging for load-bearingwalls and posts.
■ Improves drywall finishing around doors and windows. No screw head buildup.
■ Superior axial strength.
The highly innovative multipurpose HDS® Framing Systemprovides cost-effective, member-reducing framingsolutions for headers, jambs, posts and heavy-duty, built-up tube truss chords and webs.
Applications
■ Curtain-wall headers, jambs and sills.
■ Drywall headers and jambs.
■ Load-bearing jambs.
■ Trusses.
■ Shearwall posts.
■ Heavily loaded or long-span wall studs.
■ Any other application involving nested stud and track.
Table Notes
1) Based on a wall height of 12' with 1' parapet, with 30 psfwind load and L/600 deflection.
2) Assumed screw cost is $0.02 per screw.3) Framing labor assumed to be $1.00 per foot of header.4) Labor savings associated with header installation neglected.
Window Material Costs Labor CostsTotal
Width Conventional HDSSavings
Conventional HDSSavings Savings
(ft.) Framing Framing Framing Framing6 $67 $66 $1 (2%) $38 $19 $19 (50%) $20 (19%)8 $107 $104 $3 (3%) $71 $21 $50 (70%) $53 (30%)10 $138 $122 $16 (12%) $92 $23 $69 (75%) $85 (37%)
HDS® Cost Savings for Window Headers and Jambs
3"6"
3"3-5/8
2-1/4"
1-1/16"
5-7/8"
3-1/2" 3-1/16"
3-1/16"
2"
2"
HDS
HDSC
Patent Pending
HD
S®Fr
amin
g Sy
stem
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:05 AM Page 72
73For more information or to contact a sales representative, see page 3
Headers, Jambs, Posts
HDS Replaces Built-up Curtain-wall Headers
HDS Replaces Load-Bearing Box Beam Headers
HDS Replaces or Reduces Jambs and Posts
HD
S®
Framing System
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:06 AM Page 73
HDS Replaces Built-up or Tube Truss Chords
HDS Simplifies Shear-wall Framing
HD
S®Fr
amin
g Sy
stem
74 The place to stop…before the building starts! SMrequest a quote online @
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:06 AM Page 74
75For more information or to contact a sales representative, see page 3
HD
S®
Framing System
Headers, Jambs, Posts
The HDS® Framing System is a new, high-performance, cost-effective, multipurpose, heavy-duty framing stud forheaders, jambs, posts and built-up tube truss chords andwebs. The superior strength and carrying capacity of theHDS means higher performance with fewer members. Itmeans eliminating box beam headers, nesting track andstud for posts and jambs and eliminating multimemberbuilt-up truss chords and webs. It also means improvedfinish quality by eliminating excessive material and screwhead buildup around doors and windows.
The HDSC header bracket is the perfect complement tothe HDS® Framing system. This simple, yet innovativeheader bracket turns curtain-wall header installation from atwo- man job into a one-person job. This unique,prepunched clip also eliminates surface head fastenerbuildup that can create finishing challenges. Let the light-gauge framing experts at Dietrich Design Group help youincorporate this new, cutting-edge, framing assembly intoyour next project. Photocopy and complete the HDSPreliminary Sizing Sheet on page 143 for FREE HDSPreliminary Sizing. The HDS Preliminary Sizing Sheet canalso be downloaded from our websitewww.dietrichmetalframing.com or contact DDG at 1-800-873-2443.
Product DimensionsHDS® —Heavy Duty Stud 3-5/8" x 3" x 1-1/16" x 3/4" (92.1mm x 76.2mm x 27.0mm x 19.1mm)6" x 3" x 2-1/4" x 3/4" (152mm x 76.2mm x 57.2mm x 19.1mm)HDSC—Header Brackets3-1/2" x 3-1/16" x 2 (88.9mm x 77.8mm x 50.8mm )5-7/8" x 3-1/16" x 2 (149mm x 77.8mm x 50.8mm)
Material SpecificationsHDSGauge: 20 gauge (33 mils)Design Thickness: 0.0346 inches (0.879 mm)Gauge: 18 gauge (43 mils)Design Thickness: 0.0451 inches (1.145 mm)Gauge: 16 gauge (54 mils)Design Thickness: 0.0566 inches (1.438 mm)Gauge: 14 gauge (68 mils)Design Thickness: 0.0713 inches (1.811 mm)Gauge: 12 gauge (97 mils)Design Thickness: 0.1017 inches (2.583 mm)Coating: G 60 (Z180) hot-dipped galvanized coating orequivalent corrosion resistance.Yield Strength: 33 ksi (230MPa)or 50 ksi (340MPa)* 33 ksi for 20 and 18 gauge. 50 ksi for 16, 14 and 12 gauge.ASTM: A 653/A 653M
HDSC Header BracketGauge: 14 gauge (68 mils)Design Thickness: 0.0713 inches (1.811 mm)Coating: G 90 (Z275) hot-dipped galvanized coatingYield Strength: Mill-certified SS Grade 50 ksi (340MPa)ASTM: A 653/A 653M
InstallationInstallation will vary based on framing application and use.Consult Dietrich Design Group (DDG) for assistance.
Patent Pending
Photo courtesy of Blackhawk Interiors, Inc., Morgantown, WV
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:06 AM Page 75
WebMin.
Unperforated Section Properties Torsional PropertiesSize Ga Mils
Fy Delivered
(in)(ksi) Thickness Area Wt. Ix Sx rx Iy Sy ry Jx1000 Cw Xo Ro
(in) (in.^2) (lb./ft.) (in.^4) (in.^3) (in.) (in.^4) (in.^3) (In.) (in.^4) (in.^6) (in.) (in.) Beta20 33 33 0.0329 0.445 1.51 0.934 0.515 1.448 0.631 0.405 1.190 0.178 4.700 -3.427 3.906 0.23018 43 33 0.0428 0.574 1.94 1.198 0.661 1.444 0.805 0.516 1.184 0.389 5.896 -3.405 3.884 0.231
3.625 16 54 50 0.0538 0.715 2.41 1.483 0.818 1.441 0.990 0.632 1.177 0.764 7.093 -3.381 3.859 0.23214 68 50 0.0677 0.888 3.00 1.829 1.009 1.436 1.211 0.770 1.168 1.503 8.452 -3.349 3.827 0.23412 97 50 0.0966 1.239 4.19 2.520 1.390 1.426 1.645 1.039 1.152 4.271 10.869 -3.289 3.766 0.23720 33 33 0.0329 0.610 2.06 3.034 1.011 2.230 0.993 0.644 1.276 0.244 25.386 -3.591 4.415 0.33918 43 33 0.0428 0.788 2.66 3.907 1.302 2.226 1.273 0.824 1.271 0.533 32.231 -3.574 4.398 0.340
6 16 54 50 0.0538 0.984 3.32 4.856 1.619 2.222 1.573 1.016 1.265 1.052 39.292 -3.555 4.379 0.34114 68 50 0.0677 1.226 4.14 6.023 2.008 2.216 1.938 1.249 1.257 2.076 47.660 -3.531 4.354 0.34312 97 50 0.0966 1.722 5.82 8.380 2.793 2.206 2.662 1.707 1.243 5.936 63.365 -3.482 4.306 0.346
HDS® Properties
Unperforated Bending Properties Perforated Bending Properties Eff. Moment of InertiaWeb
Web in Ten. Web in Comp. Web in Ten. Web in Comp.Web in Web in
Size Ga Mils Sxe Mxa Sxe Mxa Ixe Ten. Comp.(in) (in.^3) (in.-lb.) Sye Mya Sye Mya (in.^3) (in.-lb.) Sye Mya Sye Mya (in.^4) Iye Iye
(in.^3) (in.-lb.) (in.^3) (in.-lb.) (in.^3) (in.-lb.) (in.^3) (in.-lb.) (in.^4) (in.^4)20 33 0.397 7846 0.401 7917 0.294 5814 0.367 7247 0.313 6192 0.243 4804 0.851 0.631 0.53718 43 0.565 11165 0.516 10187 0.425 8401 0.540 10674 0.400 7903 0.342 6753 1.161 0.805 0.741
3.625 16 54 0.711 21290 0.632 18925 0.535 16019 0.683 20464 0.492 14739 0.429 12844 1.449 0.990 0.92114 68 0.958 28672 0.770 23063 0.733 21944 0.939 28127 0.603 18051 0.572 17117 1.829 1.211 1.19412 97 1.390 41626 1.039 31111 1.039 31111 1.375 41154 0.820 24551 0.820 24551 2.520 1.645 1.64520 33 0.769 15192 0.532 10508 0.329 6505 0.752 14868 0.514 10153 0.275 5434 2.822 0.954 0.69418 43 1.150 22733 0.762 15066 0.483 9535 1.141 22553 0.697 13773 0.394 7792 3.797 1.273 0.981
6 16 54 1.449 43377 0.927 27741 0.610 18261 1.438 43053 0.865 25884 0.498 14913 4.753 1.573 1.22914 68 1.925 57642 1.226 36698 0.854 25573 1.916 57361 1.078 32268 0.686 20533 6.023 1.938 1.64512 97 2.793 83631 1.707 51102 1.429 42793 2.784 83346 1.484 44433 1.122 33607 8.380 2.662 2.522
Other PropertiesWeb
Unperforated PerforatedSize Ga Mils Lu
Vx VxVy Px Py
(in) (in)(kips) (kips)
(kips) (kips) (kips)
20 33 103 1.03 0.54 2.05 0.29 0.3818 43 103 1.74 0.68 3.09 0.46 0.61
3.625 16 54 83 3.38 1.02 5.77 1.02 1.3814 68 82 4.37 1.00 7.06 1.51 2.0812 97 82 6.05 0.92 9.71 2.85 4.0020 33 126 0.63 0.63 2.05 0.27 0.3818 43 125 1.41 1.24 3.09 0.43 0.61
6 16 54 101 2.83 1.95 5.77 0.97 1.3814 68 101 5.34 2.88 7.06 1.44 2.0812 97 100 10.58 3.90 9.71 2.74 4.00
Table Notes
Lu=Maximum unbraced length to attain Mxa.Vx=Allowable Shear for bending about x-axis.Vy=Allowable Shear for bending about y-axis.Px=Allowable Web Crippling per AISI Standard for CFSWall Stud Design 2004. This value assumes the webresists web crippling and the HDS is nested in trackhaving the same thickness. Bearing length is 1.25".Py=Allowable End One Flange Web Crippling per AISINASPEC 2001. This value assumes 2 flanges resist webcrippling for a bearing length of 1.25".
Ix=Gross Moment of Inertia about x-axis.Sx=Gross Section Modulus about x-axis.rx=Gross Radius of Gyration about x-axis.Iy=Gross Moment of Inertia about y-axis.Sy=Gross Section Modulus about y-axis.ry=Gross Radius of Gyration about y-axis.J=St. Venant Torsion Constant.Cw=Warping Torsion Constant.xo=Distance from shear center to the centroid along theprincipal x-axis.ro=Polar Radius of Gyration about the centoidal principalaxis.Beta=1-(Xo/ro)^2
Sxe=Effective Section Modulus about x-axis.Mxa=Allowable Moment about x-axis.Sye=Effective Section Modulus about y-axis.Mya=Allowable Moment about y-axis.Ixe=Effective Moment of Inertia about x-axis for deflection calculations.Iye=Effective Moment of Inertia about y-axis for deflection calculations.
Unless otherwise noted, properties are computedaccording to the AISI NASPEC, 2001.Perforated properties are based on the standard 1.5" x 4"oval Dietrich web knockout.
Clip Jamb/ Jamb/F1 (lbs) F2 (lbs)
Size Designation Head Gauge Head Gauge(Inches) Gauge (mils) Fy Jamb Head Jamb Head
20 (33) 33 560 453 560 44918 (43) 33 832 673 832 713
16 (54)33 1172 948 890 890
3.5 HDSC50 1680 1359 890 890
14 (68)33 1656 1339 890 89050 1680 1359 890 890
12 (97)33 1680 1359 890 89050 1680 1359 890 890
20 (33) 33 560 501 560 44918 (43) 33 832 744 832 713
16 (54)33 1172 1048 1172 1064
5-7/8 HDSC50 1680 1503 1493 1493
14 (68)33 1656 1481 1493 149350 1680 1503 1493 1493
12 (97)33 1680 1503 1493 149350 1680 1503 1493 1493
Allowable Loads for HDSC Header Brackets (lbs)
Table Notes
1) Screws shall be #10-16 Buildex or equivalent, with an ultimate shear capacity per screw of 1400#.2) Table to be used by qualified engineers only.3) To determine the capacity of any given connection, compare the jamb and head values, and use the minimum. For example, if a 16-gauge, 50 ksi jamb is used with a
3.625" HDS 18-gauge, 33 ksi head, the design value for F1 is the minimum value of 1680# for the jamb and 682# for the head. Therefore, the design value is 682#.4) For F1 and F2 occurring at the same time, use the squared interaction equation: (f1/F1)^2+(f2/F2)^2<1.0.
Patent Pending
HD
S®Fr
amin
g Sy
stem
76 The place to stop…before the building starts! SMrequest a quote online @
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:06 AM Page 76
77For more information or to contact a sales representative, see page 3
Headers, Jambs, Posts
WallDeflection
HeightMember
GaugeMils Fy 240 360 600
(ft)Size (in) (ksi) Opening Height (ft)(in)
8 10 12 14 8 10 12 14 8 10 12 1420 33 33 11' 0'' — — — 10' 4'' — — — 9' 6'' — — —18 43 33 11' 6'' — — — 10' 10'' — — — 10' 0'' — — —
3.625 16 54 50 11' 11'' — — — 11' 3'' — — — 10' 4'' — — —14 68 50 12' 3'' — — — 11' 7'' — — — 10' 9'' — — —
912 97 50 12' 10'' — — — 12' 2'' — — — 11' 3'' — — —20 33 33 12' 12'' — — — 12' 4'' — — — 11' 6'' — — —18 43 33 13' 5'' — — — 12' 10'' — — — 11' 12'' — — —
6 16 54 50 13' 9'' — — — 13' 2'' — — — 12' 4'' — — —14 68 50 14' 1'' — — — 13' 6'' — — — 12' 9'' — — —12 97 50 14' 5'' — — — 13' 11'' — — — 13' 3'' — — —20 33 33 9' 2'' 11' 12'' — — 9' 2'' 11' 3'' — — 9' 2'' 10' 5'' — —18 43 33 10' 6'' 12' 7'' — — 10' 6'' 11' 9'' — — 9' 11'' 10' 11'' — —
3.625 16 54 50 11' 11'' 13' 0'' — — 11' 2'' 12' 2'' — — 10' 4'' 11' 3'' — —14 68 50 12' 3'' 13' 6'' — — 11' 7'' 12' 8'' — — 10' 9'' 11' 8'' — —
1112 97 50 12' 10'' * 14' 2'' — — 12' 2'' 13' 4'' — — 11' 3'' 12' 3'' — —20 33 33 12' 0'' 14' 5'' — — 12' 0'' 13' 7'' — — 11' 6'' 12' 6'' — —18 43 33 12' 11'' * 15' 0'' — — 12' 10'' * 14' 2'' — — 11' 12'' 13' 1'' — —
6 16 54 50 13' 7'' * 15' 6'' — — 13' 2'' * 14' 8'' — — 12' 4'' 13' 7'' — —14 68 50 14' 1'' * 15' 11'' — — 13' 6'' * 15' 2'' — — 12' 9'' * 14' 1'' — —12 97 50 14' 5'' * 16' 7'' — — 13' 11'' * 15' 10'' — — 13' 3'' * 14' 9'' — —20 33 33 7' 7'' 9' 2'' 11' 11'' — 7' 7'' 9' 2'' 11' 11'' — 7' 7'' 9' 2'' 10' 6'' —18 43 33 8' 8'' * 10' 5'' 13' 6'' — 8' 8'' * 10' 5'' 12' 8'' — 8' 8'' * 10' 5'' 11' 4'' —
3.625 16 54 50 10' 8'' * 12' 2'' 13' 11'' — 10' 8'' * 12' 2'' 13' 1'' — 10' 3'' * 11' 1'' 12' 2'' —14 68 50 11' 3'' * 12' 9'' * 14' 5'' — 11' 3'' * 12' 7'' * 13' 7'' — 10' 8'' * 11' 7'' 12' 7'' —
1312 97 50 12' 1'' * 13' 9'' * 15' 2'' — 12' 1'' * 13' 3'' * 14' 3'' — 11' 3'' * 12' 3'' 13' 2'' —20 33 33 9' 11'' * 11' 10'' 15' 6'' — 9' 11'' * 11' 10'' 14' 6'' — 9' 11'' * 11' 10'' 13' 5'' —18 43 33 11' 4'' * 12' 11'' * 16' 2'' — 11' 4'' * 12' 11'' * 15' 2'' — 11' 4'' * 12' 11'' * 14' 0'' —
6 16 54 50 11' 12'' * 13' 7'' * 16' 9'' — 11' 12'' * 13' 7'' * 15' 9'' — 11' 12'' * 13' 7'' * 14' 6'' —14 68 50 12' 8'' * 14' 4'' * 17' 4'' — 12' 8'' * 14' 4'' * 16' 4'' — 12' 8'' * 14' 1'' * 15' 1'' —12 97 50 13' 8'' * 15' 6'' * 18' 2'' — 13' 8'' * 15' 6'' * 17' 2'' — 13' 3'' * 14' 9'' * 15' 11'' —20 33 33 6' 7'' * 7' 7'' 9' 2'' 11' 11'' 6' 7'' * 7' 7'' 9' 2'' 11' 11'' 6' 7'' * 7' 7'' 9' 2'' 10' 6''18 43 33 7' 7'' * 8' 8'' * 10' 5'' 13' 7'' 7' 7'' * 8' 8'' * 10' 5'' 12' 12'' 7' 7'' * 8' 8'' * 10' 5'' 11' 4''
3.625 16 54 50 9' 9'' * 10' 8'' * 12' 2'' 14' 10'' 9' 9'' * 10' 8'' * 12' 2'' 13' 9'' 9' 9'' * 10' 8'' * 11' 5'' 12' 0''14 68 50 10' 4'' * 11' 3'' * 12' 9'' * 15' 4'' 10' 4'' * 11' 3'' * 12' 9'' * 14' 6'' 10' 4'' * 11' 3'' * 12' 3'' * 12' 9''
1512 97 50 11' 2'' * 12' 1'' * 13' 9'' * 16' 1'' 11' 2'' * 12' 1'' * 13' 9'' * 15' 2'' 11' 2'' * 12' 1'' * 12' 12'' * 13' 11''20 33 33 8' 7'' * 9' 10'' * 11' 10'' 15' 4'' 8' 7'' * 9' 10'' * 11' 10'' 15' 4'' 8' 7'' * 9' 10'' * 11' 10'' 14' 4''18 43 33 10' 1'' * 11' 4'' * 12' 11'' * 16' 12'' 10' 1'' * 11' 4'' * 12' 11'' * 16' 1'' 10' 1'' * 11' 4'' * 12' 11'' * 14' 11''
6 16 54 50 11' 0'' * 11' 12'' * 13' 7'' * 17' 9'' * 11' 0'' * 11' 12'' * 13' 7'' * 16' 8'' 11' 0'' * 11' 12'' * 13' 7'' * 15' 5''14 68 50 11' 7'' * 12' 8'' * 14' 4'' * 18' 5'' * 11' 7'' * 12' 8'' * 14' 4'' * 17' 4'' 11' 7'' * 12' 8'' * 14' 4'' * 15' 12''12 97 50 12' 7'' * 13' 8'' * 15' 6'' * 19' 5'' * 12' 7'' * 13' 8'' * 15' 6'' * 18' 3'' * 12' 7'' * 13' 8'' * 15' 6'' * 16' 10''
Interior Span ChartAllowable HDS® Header Spans for Window and Door Openings (Dead Load=10psf & Wind Load=5psf)(Dead Load Deflection Limited to L/240 or a Maximum of 0.5 in.)
Table Notes
1) Tabulated values are for a single HDSheader installed with standard HDSclips. Each head-to-jamb connectionrequires (4) #10-16 screws to theheader, and (4) #10-16 screws to thejamb. Tabulated values marked with anasterisk will require special engineeringof the header-to-jamb connections.
2) Tabulated values include a connectioncheck assuming 25 gauge jamb studs.
3) HDS Header to be installed with openside facing up.
4) HDS properties computed inaccordance with AISI NASPEC 2001.
WallHeight
Opening
HDS Header
Header Span
OpeningHeight
F1
F2
Patent Pending
HD
S®
Framing System
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:06 AM Page 77
78 The place to stop…before the building starts! SMrequest a quote online @
WallDeflection
HeightMember
GaugeMils Fy 240 360 600
(ft)Size
(in) (ksi) Opening Height (ft)(in)
8 10 12 14 8 10 12 14 8 10 12 1420 33 33 7' 5" — — — 7' 5" — — — 7' 5" — — —18 43 33 8' 6" — — — 8' 6" — — — 8' 3" — — —
3.625 16 54 50 9' 10" — — — 9' 3" — — — 8' 6" — — —14 68 50 10' 2" — — — 9' 7" — — — 8' 10" — — —12 97 50 10' 9" — — — 10' 1" — — — 9' 3" — — —
9 20 33 33 9' 7" — — — 9' 7" — — — 9' 5" — — —18 43 33 11' 5" — — — 10' 9" — — — 9' 11" — — —
6 16 54 50 11' 9" — — — 11' 1" — — — 10' 3" — — —14 68 50 12' 2" — — — 11' 6" — — — 10' 8" — — —12 97 50 12' 9" — — — 12' 1" — — — 11' 2" — — —20 33 33 6' 1" 7' 5" — — 6' 1" 7' 5" — — 6' 1" 7' 5" — —18 43 33 7' 0" 8' 6" — — 7' 0" 8' 6" — — 7' 0" 8' 3" — —
3.625 16 54 50 9' 2" 10' 9" — — 9' 1" 9' 11" — — 8' 3" 8' 8" — —14 68 50 10' 2" 11' 1" — — 9' 6" 10' 5" — — 8' 7" 9' 3" — —12 97 50 10' 8" 11' 8" — — 10' 0" 10' 11" — — 9' 2" 10' 2" — —
11 20 33 33 7' 11" 9' 6" — — 7' 11" 9' 6" — — 7' 11" 9' 6" — —18 43 33 9' 4" 11' 1" — — 9' 4" 11' 1" — — 9' 4" 10' 9" — —
6 16 54 50 11' 9" 12' 11" — — 11' 1" 12' 1" — — 10' 3" 11' 2" — —14 68 50 12' 2" 13' 4" — — 11' 6" 12' 7" — — 10' 7" 11' 7" — —12 97 50 12' 9" 14' 1" — — 12' 1" 13' 3" — — 11' 2" 12' 2" — —20 33 33 5' 3" 6' 1" 7' 5" — 5' 3" 6' 1" 7' 5" — 5' 3" 6' 1" 7' 5" —18 43 33 6' 1" 7' 0" 8' 6" — 6' 1" 7' 0" 8' 6" — 6' 1" 7' 0" 8' 3" —
3.625 16 54 50 8' 0" 9' 2" 10' 9" — 8' 0" 9' 2" 9' 11" — 7' 7" 8' 1" 8' 8" —14 68 50 9' 0" 10' 3" 11' 9" — 9' 0" 9' 11" 10' 7" — 8' 4" 8' 8" 9' 3" —12 97 50 10' 7" 11' 6" 12' 7" — 9' 11" 10' 9" 11' 6" — 8' 12" 9' 5" 10' 1" —
13 20 33 33 6' 11" 7' 11" 9' 6" — 6' 11" 7' 11" 9' 6" — 6' 11" 7' 11" 9' 6" —18 43 33 8' 1" 9' 4" 11' 0" — 8' 1" 9' 4" 11' 0" — 8' 1" 9' 4" 11' 0" —
6 16 54 50 10' 10" 12' 2" 13' 10" — 10' 10" 11' 12" 12' 12" — 10' 2" 10' 12" 11' 10" —14 68 50 12' 1" 13' 4" 14' 4" — 11' 6" 12' 6" 13' 5" — 10' 7" 11' 5" 12' 6" —12 97 50 12' 9" 14' 0" 15' 1" — 12' 1" 13' 2" 14' 2" — 11' 2" 12' 1" 13' 1" —20 33 33 4' 8" 5' 3" 6' 1" 7' 5" 4' 8" 5' 3" 6' 1" 7' 5" 4' 8" 5' 3" 6' 1" 7' 5"18 43 33 5' 5" 6' 1" 7' 0" 8' 6" 5' 5" 6' 1" 7' 0" 8' 6" 5' 5" 6' 1" 7' 0" 8' 3"
3.625 16 54 50 7' 2" 8' 0" 9' 2" 10' 9" 7' 2" 8' 0" 9' 2" 9' 11" 7' 2" 7' 7" 8' 1" 8' 8"14 68 50 8' 1" 9' 0" 10' 3" 11' 9" 8' 1" 9' 0" 9' 11" 10' 7" 7' 9" 8' 2" 8' 8" 9' 3"12 97 50 9' 6" 10' 6" 11' 10" 12' 9" 9' 6" 10' 5" 10' 10" 11' 6" 8' 9" 8' 11" 9' 5" 10' 1"
15 20 33 33 6' 2" 6' 11" 7' 11" 9' 6" 6' 2" 6' 11" 7' 11" 9' 6" 6' 2" 6' 11" 7' 11" 9' 6"18 43 33 7' 3" 8' 1" 9' 4" 11' 0" 7' 3" 8' 1" 9' 4" 11' 0" 7' 3" 8' 1" 9' 4" 11' 0"
6 16 54 50 9' 8" 10' 8" 12' 1" 13' 11" 9' 8" 10' 8" 12' 1" 13' 6" 9' 8" 10' 8" 11' 2" 11' 10"14 68 50 10' 11" 12' 0" 13' 5" 15' 3" 10' 11" 12' 0" 13' 3" 14' 5" 10' 7" 11' 4" 11' 11" 12' 7"12 97 50 12' 0" 13' 1" 14' 10" 15' 12" 12' 0" 13' 1" 14' 0" 15' 1" 11' 2" 12' 0" 12' 10" 13' 8"
Exterior Span ChartAllowable HDS® Header Spans for Window and Door Openings (Dead Load=12psf & Wind Load=25psf)(Dead Load Deflection Limited to L/240 or a Maximum of 0.5 in.)
WallHeight
Opening
HDS Header
Header Span
OpeningHeight
Table Notes
1) Tabulated values are for a single HDS header installed withstandard HDSC clips. Each head-to-jamb connection requires (4) #10-16 screws to the header, and (4) #10-16 screws to thejamb. Tabulated values marked with an asterisk will requirespecial engineering of the header-to-jamb connections.
2) Deflections are computed using 0.7 times the components andcladding wind load per Section B1 of the AISI Standard for Cold-Formed Steel Framing - Wall Design. Note that the 0.7 factor is not used for the interior 5 psf loading condition.
3) Unless connections are engineered separately, jambs must bethe same gauge and strength as the header.
4) HDS Header to be installed with open side facing up.5) HDS properties computed in accordance
with AISI NASPEC 2001.
Patent Pending
HD
S®Fr
amin
g Sy
stem
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:06 AM Page 78
79For more information or to contact a sales representative, see page 3
Table Notes
1) The opening is centered vertically about the wall height.
2) The assumed stud spacing adjacent to the opening is 16" O/C or less. For door openings, this table is conservative, and therefore valid.
3) The tabulated values assume a single HDS memberis used at each jamb stud.
4) The tabulated values are limited to 16' for 3.625"walls and 20' for 6" walls. For wider openings orother conditions, contact Dietrich Design Group at 1-800-873-2443.
5) Depending on the actual window width versus thetabulated window width, cells marked with anasterisk may require an end connection that willprevent web crippling. Web crippling is computed inaccordance with the AISI Standard for CFS Wall StudDesign 2004. End track must have a minimumthickness equal to the jamb stud.
6) The tabulated values are based on an unbracedlength of 6' for bending.
7) HDS properties computed in accordance with the2001 AISI NASPEC.
8) Table not valid for openings in load-bearing walls.
5 psfWall Member
Mils FyDeflection
Height Size Gauge(in) (ksi)
240 360 600(ft) (in) Sill Height
2 3 2 3 2 320 33 33 16' 0'' 16' 0'' 16' 0'' 16' 0'' 12' 10" 11' 2"18 43 33 16' 0'' 16' 0'' 16' 0'' 16' 0'' 16' 0'' 16' 0''
3.625 16 54 50 16' 0'' 16' 0'' 16' 0'' 16' 0'' 16' 0'' 16' 0''14 68 50 16' 0'' 16' 0'' 16' 0'' 16' 0'' 16' 0'' 16' 0''
912 97 50 16' 0'' 16' 0'' 16' 0'' 16' 0'' 16' 0'' 16' 0''20 33 33 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0''18 43 33 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0''
6 16 54 50 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0''14 68 50 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0''12 97 50 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0''20 33 33 16' 0'' 16' 0'' 12' 1" 10' 6" 5' 8" 5' 7"18 43 33 16' 0'' 16' 0'' 16' 0'' 15' 3" 9' 2" 8' 2"
3.625 16 54 50 16' 0'' 16' 0'' 16' 0'' 16' 0'' 12' 5" 10' 9"14 68 50 16' 0'' 16' 0'' 16' 0'' 16' 0'' 16' 0'' 14' 3"
1112 97 50 16' 0'' 16' 0'' 16' 0'' 16' 0'' 16' 0'' 16' 0''20 33 33 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0''18 43 33 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0''
6 16 54 50 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0''14 68 50 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0''12 97 50 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0''20 33 33 10' 8" 9' 8" 5' 9" 5' 6" 2' 8" —18 43 33 16' 0'' 14' 4" 9' 10" 8' 6" 4' 3" 4' 1"
3.625 16 54 50 16' 0'' 16' 0'' 12' 11" 11' 4" 5' 11" 5' 8"14 68 50 16' 0'' 16' 0'' 16' 0'' 15' 2" 8' 8" 6' 0"
1312 97 50 16' 0'' 16' 0'' 16' 0'' 16' 0'' 13' 9" 11' 12"20 33 33 20' 0'' * 20' 0'' 20' 0'' * 20' 0'' 16' 2" 13' 10"18 43 33 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0'' 19' 8"
6 16 54 50 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0''14 68 50 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0''12 97 50 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0''20 33 33 5' 6" 5' 4" 3' 1" 2' 11" — —18 43 33 8' 8" 8' 4" 4' 10" 4' 8" — —
3.625 16 54 50 12' 3" 11' 3" 6' 7" 6' 4" 3' 2" 3' 0"14 68 50 16' 0'' 15' 4" 9' 4" 9' 2" 4' 5" 4' 3"
1512 97 50 16' 0'' 16' 0'' 15' 7" 13' 8" 7' 0" 6' 9"20 33 33 20' 0'' * 20' 0'' * 18' 6" * 15' 10" 8' 3" 7' 11"18 43 33 20' 0'' 20' 0'' 20' 0'' 20' 0'' 13' 3" 11' 12"
6 16 54 50 20' 0'' 20' 0'' 20' 0'' 20' 0'' 18' 9" 16' 1"14 68 50 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0''12 97 50 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0'' 20' 0''
Allowable Opening Widths for Single HDS® Framing Used as Jamb Studs
WallHeight
Opening
Tabulated Width
Sill Height
HD
S®
Framing System
Headers, Jambs, Posts
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:06 AM Page 79
25 psf 35 psfWall Member
Mils FyDeflection Deflection
Height Size Gauge(in) (ksi)
240 360 600 240 360 600(ft) (in) Sill Height Sill Height
2 3 2 3 2 3 2 3 2 3 2 320 33 33 3' 3" 3' 0" 3' 3" 3' 0" — — — — — — — — 18 43 33 6' 4" 5' 4" 6' 4" 5' 4" 3' 4" 3' 1" 3' 7" 3' 4" 3' 7" 3' 4" — —
3.625 16 54 50 13' 6" 11' 6" 9' 10" 8' 8" 4' 11" 4' 3" 9' 3" 7' 9" 6' 2" 5' 6" 2' 9" —14 68 50 16' 0'' 14' 11" 13' 2" 11' 6" 6' 9" 5' 12" 11' 2" 10' 3" 8' 7" 7' 7" 3' 12" 3' 10"12 97 50 16' 0'' 16' 0'' 16' 0'' 16' 0'' 10' 5" 9' 1" 12' 1" 12' 5" 12' 1" 11' 3" 6' 7" 5' 10"
9 20 33 33 8' 9" * 7' 7" * 8' 9" * 7' 7" * 8' 9" * 7' 7" * 4' 0" * 4' 11" * 4' 0" * 4' 11" * 4' 0" * 4' 11" *18 43 33 15' 8" * 13' 2" * 15' 8" * 13' 2" * 15' 8" * 13' 2" * 10' 9" * 8' 10" * 10' 9" * 8' 10" * 10' 9" * 8' 10" *
6 16 54 50 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 19' 3" 20' 0" * 17' 9" * 20' 0" * 17' 9" * 15' 0" * 13' 1"14 68 50 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 19' 10" 17' 2"12 97 50 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0"20 33 33 — — — — — — — — — — — — 18 43 33 3' 3" 2' 12" 2' 11" 2' 8" — — — — — — — —
3.625 16 54 50 6' 0" 6' 12" 4' 2" 3' 10" — — 4' 7" 4' 4" — — — — 14 68 50 10' 10" 9' 6" 5' 11" 5' 9" 2' 8" — 6' 10" 6' 1" 3' 6" 3' 3" — — 12 97 50 13' 2" 13' 1" 9' 7" 8' 6" 4' 5" 4' 1" 9' 1" 8' 11" 5' 9" 5' 7" 2' 7" —
11 20 33 33 5' 6" * 5' 5" * 5' 6" * 5' 5" * 5' 3" * 5' 1" * 3' 3" * 2' 11" * 3' 3" * 2' 11" * 3' 2" * 2' 10" *18 43 33 10' 12" * 9' 5" * 10' 12" * 9' 5" * 8' 3" * 7' 5" * 6' 6" * 4' 0" * 6' 6" * 4' 0" * 4' 12" * 4' 9" *
6 16 54 50 20' 0" * 18' 10" * 20' 0" * 18' 3" * 11' 5" 9' 11" 15' 4" * 12' 12" * 14' 5" * 12' 4" * 7' 4" 6' 5"14 68 50 20' 0" 20' 0" 20' 0" 20' 0" 15' 7" 13' 3" 20' 0" * 18' 4" 19' 5" * 16' 3" 9' 11" 8' 9"12 97 50 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 19' 6" 20' 0" 20' 0" 20' 0" 20' 0" 15' 6" 13' 2"20 33 33 — — — — — — — — — — — — 18 43 33 — — — — — — — — — — — —
3.625 16 54 50 3' 7" 3' 5" — — — — — — — — — — 14 68 50 5' 1" 4' 10" 2' 9" 2' 7" — — 3' 1" 2' 11" — — — — 12 97 50 8' 4" 6' 0" 4' 6" 4' 3" — — 4' 12" 4' 9" 2' 8" 2' 6" — —
13 20 33 33 3' 3" * 3' 1" * 3' 3" * 3' 1" * — — — — — — — — 18 43 33 6' 2" * 5' 11" * 6' 2" * 5' 11" * 3' 10" 3' 8" 3' 9" * 3' 6" * 3' 9" * 3' 6" * — —
6 16 54 50 17' 9" * 14' 9" * 11' 9" 10' 5" 5' 5" 5' 2" 10' 4" * 9' 5" * 6' 12" 6' 9" 3' 3" 3' 1"14 68 50 20' 0" 20' 0" 16' 6" 14' 1" 7' 8" 7' 6" 16' 6" * 14' 0" 10' 1" 9' 2" 4' 8" 4' 5"12 97 50 20' 0" 20' 0" 20' 0" 20' 0" 12' 9" 11' 3" 20' 0" 20' 0" 16' 4" 13' 12" 7' 7" 7' 5"20 33 33 — — — — — — — — — — — — 18 43 33 — — — — — — — — — — — —
3.625 16 54 50 — — — — — — — — — — — — 14 68 50 2' 8" 2' 7" — — — — — — — — — — 12 97 50 4' 4" 4' 2" — — — — 2' 7" — — — — —
15 20 33 33 — — — — — — — — — — — — 18 43 33 4' 0" * 3' 11" * 4' 0" * 3' 11" * — — — — — — — —
6 16 54 50 11' 3" * 10' 2" 5' 12" 5' 10" 2' 10" 2' 9" 6' 3" 6' 1" 3' 9" 3' 7" — — 14 68 50 16' 2" * 14' 2" 8' 6" 8' 2" 4' 1" 3' 11" 9' 5" 9' 3" 5' 3" 5' 1" — — 12 97 50 20' 0" 20' 0" 14' 5" 12' 10" 6' 6" 6' 3" 16' 0" 14' 0" 8' 5" 8' 0" 4' 0" 3' 10"
Allowable Opening Widths for Single HDS® Framing Used as Jamb Studs
WallHeight
Opening
Tabulated Width
Sill Height
Table Notes
1) The opening is centered vertically about the wall height.2) The assumed stud spacing adjacent to the opening is 16" O/C or less.3) The tabulated values assume a single HDS member is used at each
jamb stud.4) The tabulated values are limited to 16' for 3.625" walls and 20' for
6" walls. For wider openings or other conditions, contact DietrichDesign Group at 1-800-873-2443.
5) Depending on the actual window width versus the tabulated windowwidth, cells marked with an asterisk may require an end connectionthat will prevent web crippling. Web crippling is computed inaccordance with the AISI Standard for CFS Wall Stud Design 2004. End track must have a minimum thickness equal to the jamb stud.
6) The tabulated values are based on an unbraced length for bending of 6'.
7) Deflections are computed using 0.7 times the components andcladding wind load per Section B1 of the AISI Standard for Cold-Formed Steel Framing - Wall Design. Note that the 0.7 factor is not used for the interior 5 psf loading condition.
8) HDS properties computed in accordance with the 2001 AISI NASPEC.9) Table not valid for openings in load-bearing walls.
Patent Pending
HD
S®Fr
amin
g Sy
stem
80 The place to stop…before the building starts! SMrequest a quote online @
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:06 AM Page 80
For more information or to contact a sales representative, see page 3
25 psf 35 psfWall Member
Mils FyDeflection Deflection
Height Size Gauge(in) (ksi)
240 360 600 240 360 600(ft) (in) Sill Height Sill Height
2 3 2 3 2 3 2 3 2 3 2 320 33 33 8' 2" 6' 10" 8' 2" 6' 10" 4' 8" 4' 1" 5' 0" 4' 2" 5' 0" 4' 2" 2' 7" — 18 43 33 13' 4" 10' 8" 13' 4" 10' 8" 6' 11" 6' 2" 8' 5" 7' 0" 8' 5" 7' 0" 4' 2" 3' 12"
3.625 16 54 50 16' 0'' 16' 0'' 16' 0'' 15' 3" 9' 4" 8' 3" 14' 11" 12' 5" 11' 8" 10' 3" 4' 0" 5' 3" 14 68 50 16' 0'' 16' 0'' 16' 0'' 16' 0'' 12' 5" 10' 10" 16' 0'' 15' 10" 15' 4" 13' 4" 7' 12" 7' 1" 12 97 50 16' 0'' 16' 0'' 16' 0'' 16' 0'' 16' 0'' 15' 8" 16' 0'' 16' 0'' 16' 0'' 16' 0'' 12' 1" 10' 6"
9 20 33 33 17' 7" * 15' 3" * 17' 7" * 15' 3" * 17' 7" * 15' 3" * 12' 2" * 10' 5" * 12' 2" * 10' 5" * 12' 2" * 10' 5" *18 43 33 20' 0" * 20' 0" 20' 0" * 20' 0" 20' 0" * 20' 0" 20' 0" * 17' 3" * 20' 0" * 17' 3" * 20' 0" * 17' 3" *
6 16 54 50 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 14 68 50 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 12 97 50 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20 33 33 4' 3" 3' 12" 3' 11" 3' 8" — — — — — — — — 18 43 33 6' 0" 6' 11" 6' 2" 5' 12" 2' 10" 2' 6" 4' 5" 4' 2" 3' 8" 3' 5" — —
3.625 16 54 50 14' 11" 12' 8" 8' 6" 7' 8" 3' 11" 3' 7" 9' 5" 8' 4" 5' 1" 4' 11" — — 14 68 50 16' 0'' 16' 0'' 11' 8" 10' 2" 5' 6" 5' 4" 12' 10" 11' 1" 7' 7" 6' 6" 3' 3" 3' 0" 12 97 50 16' 0'' 16' 0'' 16' 0'' 14' 10" 8' 10" 7' 11" 15' 3" 14' 5" 11' 4" 9' 11" 5' 4" 5' 1"
11 20 33 33 13' 4" * 11' 1" * 13' 4" * 11' 1" * 11' 0" * 9' 7" * 8' 3" * 7' 4" * 8' 3" * 7' 4" * 6' 12" * 6' 2" *18 43 33 20' 0" * 18' 4" * 20' 0" * 18' 4" * 15' 11" * 13' 6" 15' 1" * 12' 6" * 15' 1" * 12' 6" * 10' 2" * 8' 11"
6 16 54 50 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 17' 5" 20' 0" 20' 0" 20' 0" 20' 0" 13' 8" 11' 9" 14 68 50 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 18' 3" 15' 4" 12 97 50 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 20 33 33 — — — — — — — — — — — — 18 43 33 4' 5" 4' 3" 2' 11" 2' 8" — — 2' 7" — — — — —
3.625 16 54 50 7' 3" 7' 1" 3' 12" 3' 9" — — 4' 5" — — — — — 14 68 50 10' 3" 9' 3" 5' 6" 5' 3" 2' 7" — 6' 1" 3' 5" 3' 4" 3' 2" — — 12 97 50 16' 0'' 13' 11" 9' 4" 8' 2" 4' 2" 3' 11" 8' 0" 5' 6" 5' 4" 5' 1" — —
13 20 33 33 7' 11" * 6' 0" 7' 11" * 6' 0" 5' 2" 4' 11" 4' 8" * 4' 6" * 4' 8" * 4' 6" * 3' 2" 2' 12" 18 43 33 15' 6" * 13' 3" * 15' 6" * 13' 3" * 7' 10" 7' 9" 9' 5" * 8' 3" * 9' 5" * 8' 3" * 4' 9" 4' 6"
6 16 54 50 20' 0" 20' 0" 20' 0" 18' 8" 11' 1" 9' 11" 19' 6" * 13' 2" 14' 4" 12' 5" 6' 7" 6' 3" 14 68 50 20' 0" 20' 0" 20' 0" 20' 0" 15' 5" 13' 3" 20' 0" 17' 4" 19' 6" 16' 5" 9' 12" 8' 7" 12 97 50 20' 0" 20' 0" 20' 0" 20' 0" 20' 0" 19' 7" 20' 0" 20' 0" 20' 0" 20' 0" 15' 2" 13' 1" 20 33 33 — — — — — — — — — — — — 18 43 33 2' 9" 2' 8" — — — — — — — — — —
3.625 16 54 50 3' 10" 3' 8" — — — — — — — — — — 14 68 50 5' 4" 5' 1" 2' 11" 2' 9" — — 3' 3" 3' 1" — — — — 12 97 50 8' 4" 7' 12" 4' 8" 4' 6" — — 5' 2" 4' 12" 2' 10" 2' 8" — —
15 20 33 33 5' 0" * 4' 10" 5' 0" * 4' 10" 2' 9" 2' 7" 3' 0" 2' 11" 3' 0" 2' 11" — — 18 43 33 9' 1" * 9' 3" 8' 8" 8' 4" 4' 2" 3' 12" 5' 6" 5' 4" 5' 4" 5' 2" — —
6 16 54 50 20' 0" 17' 12" 12' 4" 11' 3" 5' 8" 5' 6" 10' 0" 11' 2" 7' 4" 7' 0" 3' 6" 3' 4" 14 68 50 20' 0" 20' 0" 17' 7" 15' 2" 7' 10" 7' 7" 17' 11" 15' 6" 10' 6" 8' 0" 4' 10" 4' 8" 12 97 50 20' 0" 20' 0" 20' 0" 20' 0" 13' 2" 11' 11" 20' 0" 20' 0" 17' 4" 14' 12" 7' 9" 7' 5"
Allowable Opening Widths for HDS® Framing Coupled with CSJ Studs Used as Jamb Studs
WallHeight
Opening
Tabulated Width
Sill Height
Table Notes
1) The opening is centered vertically about the wall height.2) The assumed stud spacing adjacent to the opening is 16" O/C or less.3) The tabulated values assume a single stud is also attached to the HDS
member. The assumed stud is a Dietrich CSJ of equal web size and gauge.Stud strength is assumed to be 33 ksi. Attach the stud to the HDS framingwith (2) #10-16 screws at 24" O/C as shown in the diagram left.
4) The tabulated values are limited to 16' for 3.625" walls, and 20' for 6" walls.For wider openings or other conditions, contact Dietrich Design Group at 1-800-873-2443.
5) Depending on the actual window width versus the tabulated window width,cells marked with an asterisk may require an end connection that will preventweb crippling. Web crippling is computed in accordance with the AISIStandard for CFS Wall Stud Design 2004. End track must have a minimum thickness equal to the jamb stud.
6) The tabulated values are based on an unbraced length of 6' for bending.7) Deflections are computed using 0.7 times the components and
cladding wind load per Section B1 of the AISI Standard for Cold-Formed Steel Framing - Wall Design. Note that the 0.7 factor is not used for the interior 5 psf loading condition.
8) HDS properties computed in accordance with the 2001 AISI NASPEC.9) Table not valid for openings in load-bearing walls.
HDS & Stud
HD
S®
Framing System
81
Headers, Jambs, Posts
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:06 AM Page 81
Member StudWind Load = 5 psf
Length Spacing3.625 HDS Members 6" HDS Members
(ft) (in)Gauge (Mils)
20 (33) 18 (43) 16 (54) 14 (68) 12 (97) 20 (33) 18 (43) 16 (54) 14 (68) 12 (97)12 3.37 ** 5.12 ** 8.39 ** 10.86 ** 15.07 ** 5.09 ** 8.12 ** 14.82 ** 20.91 ** 31.35 **
8 16 3.27 ** 5.01 ** 8.3 ** 10.76 ** 14.98 ** 5.03 ** 8.05 ** 14.76 ** 20.84 ** 31.27 **24 3.08 ** 4.81 ** 8.1 ** 10.58 ** 14.8 ** 4.91 ** 7.92 ** 14.62 ** 20.69 ** 31.12 **12 3.15 ** 4.8 ** 7.76 ** 9.93 ** 13.8 ** 4.97 ** 7.94 ** 14.53 ** 20.27 ** 30.32 **
9 16 3.02 ** 4.67 ** 7.64 ** 9.81 ** 13.69 ** 4.89 ** 7.86 ** 14.45 ** 20.18 ** 30.22 **24 2.78 ** 4.41 ** 7.4 ** 9.58 ** 13.47 ** 4.73 ** 7.69 ** 14.27 ** 19.99 ** 30.02 **12 2.9 ** 4.46 ** 7.09 ** 8.96 ** 12.49 ** 4.83 ** 7.74 ** 14.16 ** 19.56 ** 29.18 **
10 16 2.75 ** 4.3 ** 6.94 ** 8.82 ** 12.35 ** 4.73 ** 7.63 ** 14.05 ** 19.44 ** 29.05 **24 2.47 ** 3.99 ** 6.65 ** 8.54 ** 12.09 ** 4.53 ** 7.42 ** 13.82 ** 19.2 ** 28.8 **12 2.65 ** 4.09 ** 6.34 ** 7.98 ** 11.15 ** 4.67 ** 7.51 ** 13.63 ** 18.78 ** 27.94 **
11 16 2.47 ** 3.9 ** 6.17 ** 7.82 ** 11 ** 4.55 ** 7.38 ** 13.5 ** 18.63 ** 27.78 **24 2.15 ** 3.55 ** 5.85 ** 7.51 ** 10.7 ** 4.31 ** 7.12 ** 13.22 ** 18.33 ** 27.46 **12 2.38 ** 3.71 ** 5.55 ** 7.02 ** 9.86 ** 4.5 ** 7.26 ** 13.06 ** 17.86 ** 26.61 **
12 16 2.19 ** 3.5 ** 5.37 ** 6.84 ** 9.69 ** 4.35 ** 7.1 ** 12.9 ** 17.68 ** 26.42 **24 1.84 ** 3.11 ** 5.02 ** 6.52 ** 9.36 ** 4.07 ** 6.79 ** 12.57 ** 17.32 ** 26.03 **12 1.86 ** 2.95 ** 4.25 ** 5.44 ** 7.73 ** 4.11 ** 6.68 ** 11.72 ** 15.88 ** 23.76 **
14 16 1.65 ** 2.71 ** 4.06 ** 5.25 ** 7.54 ** 3.92 ** 6.46 ** 11.49 ** 15.63 ** 23.49 **24 1.27 * 2.29 ** 3.7 ** 4.91 ** 7.18 ** 3.55 ** 6.05 ** 11.05 ** 15.15 ** 22.96 **12 1.39 ** 2.25 ** 3.28 ** 4.25 ** 6.11 ** 3.68 ** 6.03 ** 10.28 ** 13.8 ** 20.76 **
16 16 1.17 * 2.01 ** 3.08 ** 4.06 ** 5.91 ** 3.44 ** 5.75 ** 9.99 ** 13.49 ** 20.41 **24 0.8 1.59 * 2.73 * 3.71 ** 5.55 ** 2.99 ** 5.24 ** 9.45 ** 12.9 ** 19.74 **
Allowable HDS® Axial Loads (Kips)
Member StudWind Load = 25 psf
Length Spacing3.625 HDS Members 6" HDS Members
(ft) (in)Gauge (Mils)
20 (33) 18 (43) 16 (54) 14 (68) 12 (97) 20 (33) 18 (43) 16 (54) 14 (68) 12 (97)12 2.26 ** 3.94 ** 7.28 ** 9.78 ** 14.03 ** 4.35 ** 7.33 ** 14.02 ** 20.04 ** 30.43 **
8 16 1.85 ** 3.49 ** 6.85 ** 9.35 ** 13.61 ** 4.05 ** 7.01 ** 13.7 ** 19.68 ** 30.06 **24 1.07 ** 2.64 ** 6.04 ** 8.55 ** 12.82 ** 3.46 ** 6.37 ** 13.05 ** 18.98 ** 29.31 **12 1.81 ** 3.36 ** 6.4 ** 8.61 ** 12.52 ** 4.03 ** 6.93 ** 13.49 ** 19.15 ** 29.13 **
9 16 1.33 ** 2.83 ** 5.89 ** 8.11 ** 12.03 ** 3.65 ** 6.53 ** 13.07 ** 18.69 ** 28.65 **24 0.46 * 1.87 ** 4.96 ** 7.19 ** 11.09 ** 2.92 ** 5.73 ** 12.25 ** 17.79 ** 27.69 **12 1.37 ** 2.78 ** 5.5 ** 7.44 ** 10.99 ** 3.68 ** 6.49 ** 12.85 ** 18.14 ** 27.68 **
10 16 0.85 * 2.19 ** 4.94 ** 6.89 ** 10.43 ** 3.22 ** 5.99 ** 12.32 ** 17.58 ** 27.07 **24 — 1.15 * 3.94 ** 5.89 ** 9.39 ** 2.35 ** 5.03 ** 11.31 ** 16.48 ** 25.89 **12 0.96 * 2.22 ** 4.61 ** 6.31 ** 9.48 ** 3.3 ** 6 ** 12.04 ** 17.05 ** 26.09 **
11 16 0.4 * 1.6 * 4.02 ** 5.74 ** 8.88 ** 2.76 ** 5.42 ** 11.41 ** 16.37 ** 25.36 **24 — 0.51 * 2.99 * 4.7 ** 7.79 ** 1.76 ** 4.3 ** 10.23 ** 15.07 ** 23.95 **12 0.58 * 1.7 ** 3.76 ** 5.28 ** 8.09 ** 2.9 ** 5.48 ** 11.17 ** 15.81 ** 24.39 **
12 16 0.01 1.06 * 3.18 * 4.69 ** 7.47 ** 2.29 ** 4.81 ** 10.45 ** 15.02 ** 23.53 **24 — — 2.17 * 3.67 * 6.37 ** 1.17 ** 3.55 ** 9.1 ** 13.55 ** 21.9 **12 — 0.84 * 2.46 * 3.66 * 5.86 ** 2.07 ** 4.38 ** 9.27 ** 13.21 ** 20.79 **
14 16 — 0.21 1.9 3.09 * 5.24 ** 1.35 ** 3.56 ** 8.4 ** 12.25 ** 19.71 **24 — — — 2.11 4.17 * 0.04 * 2.07 ** 6.82 ** 10.52 ** 17.74 **12 — 0.21 1.55 2.51 * 4.24 * 1.28 ** 3.29 ** 7.41 ** 10.68 ** 17.18 **
16 16 — — — 1.97 3.65 * 0.48 * 2.37 ** 6.45 ** 9.63 ** 15.97 **24 — — — — 2.64 — 0.76 * 4.78 * 7.8 ** 13.83 **
Table Notes
1) Studs are assumed to be simple span.2) Axial loads are assumed to pass through the geometric centroid of the section.3) Use 5 psf tables for interior walls.4) Cells marked with “**” meet L/600; cells marked with “*” meet L/360; unmarked cells meet L/240; blank cells do not meet L/240.5) A 1/3 stress increase is not used.6) Provide bridging and or bracing at at 5' O/C max.7) Studs are assumed to be mechanically braced. Sheathing braced design has not been used for this table.8) Studs are assumed punched with a maximum 1.5" centered web knockout at 18" O/C min.9) Capacities are calculated according to the AISI NASPEC, 2002.10) 20- and 18-gauge members are 33 ksi. 16-gauge and heavier are 50 ksi.11) Deflections are computed using 0.7 times the components and cladding wind load per Section B1 of the AISI Standard for
Cold-Formed Steel Framing - Wall Design. Note that the 0.7 factor is not used for the interior 5 psf loading condition.
3"3-5/8
1-1/16"
Pall
Patent Pending
HD
S®Fr
amin
g Sy
stem
82 The place to stop…before the building starts! SMrequest a quote online @
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:06 AM Page 82
Table Notes
1) Studs are assumed to be simple span.2) Axial loads are assumed to pass through the geometric centroid of the section.3) Use 5 psf tables for interior walls.4) Cells marked with “**” meet L/600; cells marked with “*” meet L/360; unmarked cells meet L/240; blank cells do not meet L/240.5) A 1/3 stress increase is not used.6) Provide bridging and or bracing at at 5' O/C max.7) Studs are assumed to be mechanically braced. Sheathing braced design has not been used for this table.8) Studs are assumed punched with a maximum 1.5" centered web knockout at 18" O/C min.9) Capacities are calculated according to the AISI NASPEC, 2002.10) 20- and 18-gauge members are 33 ksi. 16-gauge and heavier are 50 ksi.11) Deflections are computed using 0.7 times the components and cladding wind load per Section B1 of the AISI Standard for
Cold-Formed Steel Framing - Wall Design. Note that the 0.7 factor is not used for the interior 5 psf loading condition.
3"6"
2-1/4"
Pall
Member StudWind Load = 30 psf
Length Spacing3.625 HDS Members 6" HDS Members
(ft) (in)Gauge (Mils)
20 (33) 18 (43) 16 (54) 14 (68) 12 (97) 20 (33) 18 (43) 16 (54) 14 (68) 12 (97)12 2.01 ** 3.66 ** 7.02 ** 9.52 ** 13.78 ** 4.17 ** 7.14 ** 13.83 ** 19.83 ** 30.21 **
8 16 1.53 ** 3.14 ** 6.52 ** 9.03 ** 13.29 ** 3.81 ** 6.75 ** 13.44 ** 19.4 ** 29.76 **24 0.64 ** 2.17 ** 5.58 ** 8.09 ** 12.36 ** 3.11 ** 5.99 ** 12.67 ** 18.56 ** 28.86 **12 1.52 ** 3.04 ** 6.09 ** 8.31 ** 12.22 ** 3.8 ** 6.69 ** 13.24 ** 18.87 ** 28.84 **
9 16 0.97 ** 2.44 ** 5.51 ** 7.73 ** 11.64 ** 3.36 ** 6.2 ** 12.74 ** 18.33 ** 28.26 **24 — 1.34 * 4.45 ** 6.67 ** 10.56 ** 2.49 ** 5.26 ** 11.76 ** 17.27 ** 27.13 **12 1.05 ** 2.42 ** 5.16 ** 7.1 ** 10.65 ** 3.4 ** 6.19 ** 12.53 ** 17.8 ** 27.31 **
10 16 0.46 * 1.76 ** 4.52 ** 6.47 ** 10 ** 2.87 ** 5.6 ** 11.91 ** 17.13 ** 26.6 **24 — 0.59 * 3.39 * 5.34 ** 8.81 ** 1.85 ** 4.48 ** 10.73 ** 15.84 ** 25.2 **12 0.62 * 1.84 ** 4.25 ** 5.96 ** 9.12 ** 2.97 ** 5.65 ** 11.66 ** 16.64 ** 25.65 **
11 16 — 1.14 * 3.59 ** 5.31 ** 8.43 ** 2.35 ** 4.96 ** 10.93 ** 15.84 ** 24.79 **24 — — 2.44 * 4.14 * 7.19 ** 1.19 ** 3.66 ** 9.55 ** 14.32 ** 23.14 **12 0.23 * 1.31 * 3.41 ** 4.92 ** 7.71 ** 2.53 ** 5.07 ** 10.73 ** 15.33 ** 23.87 **
12 16 — 0.6 * 2.75 * 4.26 * 7.01 ** 1.83 ** 4.29 ** 9.89 ** 14.42 ** 22.87 **24 — — 1.63 3.12 * 5.77 * 0.53 ** 2.84 ** 8.34 ** 12.71 ** 20.98 **12 — 0.45 2.12 * 3.31 * 5.48 ** 1.63 ** 3.88 ** 8.74 ** 12.63 ** 20.14 **
14 16 — — 1.5 2.68 * 4.79 * 0.81 * 2.94 ** 7.74 ** 11.54 ** 18.89 **24 — — — 1.59 3.59 — 1.26 * 5.96 ** 9.58 ** 16.65 **12 — — 1.23 2.18 3.88 * 0.79 * 2.72 ** 6.82 ** 10.04 ** 16.44 **
16 16 — — — 1.59 3.23 — 1.69 * 5.75 ** 8.86 ** 15.08 **24 — — — — — — — 3.89 * 6.81 * 12.67 **
Allowable HDS® Axial Loads (Kips)
Member StudWind Load = 35 psf
Length Spacing3.625 HDS Members 6" HDS Members
(ft) (in)Gauge (Mils)
20 (33) 18 (43) 16 (54) 14 (68) 12 (97) 20 (33) 18 (43) 16 (54) 14 (68) 12 (97)12 1.77 ** 3.4 ** 6.77 ** 9.27 ** 13.53 ** 3.99 ** 6.94 ** 13.63 ** 19.61 ** 29.98 **
8 16 1.22 ** 2.81 ** 6.2 ** 8.71 ** 12.97 ** 3.57 ** 6.5 ** 13.18 ** 19.12 ** 29.46 **24 0.22 * 1.71 ** 5.14 ** 7.65 ** 11.91 ** 2.76 ** 5.62 ** 12.29 ** 18.14 ** 28.42 **12 1.24 ** 2.73 ** 5.79 ** 8.02 ** 11.93 ** 3.58 ** 6.45 ** 12.99 ** 18.6 ** 28.55 **
9 16 0.63 * 2.06 ** 5.14 ** 7.37 ** 11.27 ** 3.07 ** 5.89 ** 12.41 ** 17.97 ** 27.88 **24 — 0.84 * 3.96 ** 6.18 ** 10.05 ** 2.07 ** 4.81 ** 11.29 ** 16.75 ** 26.57 **12 0.75 * 2.08 ** 4.83 ** 6.78 ** 10.32 ** 3.13 ** 5.89 ** 12.22 ** 17.47 ** 26.95 **
10 16 0.09 * 1.35 * 4.13 ** 6.08 ** 9.59 ** 2.52 ** 5.22 ** 11.51 ** 16.7 ** 26.13 **24 — 0.06 * 2.88 * 4.82 * 8.26 ** 1.36 ** 3.94 ** 10.15 ** 15.22 ** 24.53 **12 0.3 * 1.48 * 3.91 ** 5.63 ** 8.77 ** 2.66 ** 5.3 ** 11.29 ** 16.23 ** 25.22 **
11 16 — 0.72 * 3.19 * 4.9 ** 8 ** 1.95 ** 4.52 ** 10.46 ** 15.32 ** 24.23 **24 — — 1.92 3.62 * 6.63 ** 0.63 ** 3.05 ** 8.89 ** 13.6 ** 22.34 **12 — 0.95 * 3.07 * 4.58 ** 7.35 ** 2.17 ** 4.68 ** 10.31 ** 14.87 ** 23.37 **
12 16 — 0.17 2.36 * 3.86 * 6.58 ** 1.38 ** 3.79 ** 9.36 ** 13.83 ** 22.22 **24 — — 1.12 2.6 5.21 * — 2.16 ** 7.61 ** 11.91 ** 20.08 **12 — 0.09 1.8 2.98 * 5.13 * 1.21 ** 3.4 ** 8.23 ** 12.07 ** 19.5 **
14 16 — — 1.13 2.29 4.37 * 0.29 * 2.36 ** 7.12 ** 10.85 ** 18.11 **24 — — — — 3.06 — 0.49 * 5.15 * 8.68 ** 15.61 **12 — — — 1.87 3.54 * 0.33 * 2.2 * 6.27 ** 9.44 ** 15.74 **
16 16 — — — — 2.83 — 1.06 * 5.1 * 8.14 ** 14.23 **24 — — — — — — — 3.05 * 5.89 * 11.6 **
Patent Pending
HD
S®
Framing System
83
Headers, Jambs, Posts
For more information or to contact a sales representative, see page 3
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:06 AM Page 83
HD
S®Fr
amin
g Sy
stem
HDS Stud WindloadMember Gauge Spacing 5 psf 10 psf 20 psf
Size (mils) (in) 240 360 600 240 360 600 240 360 60012 22' 4'' 19' 6'' 16' 6'' 17' 9'' 15' 6'' 13' 1'' 15' 7'' 13' 10'' 11' 8''
20 (33) 16 20' 4'' 17' 9'' 14' 12'' 16' 1'' 14' 1'' 11' 10'' 13' 6'' 12' 7'' 10' 7'' 24 17' 9'' 15' 6'' 13' 1'' 14' 1'' 12' 4'' 10' 4'' 10' 12'' 10' 12'' 9' 3'' 12 24' 9'' 21' 8'' 18' 3'' 19' 8'' 17' 2'' 14' 6'' 17' 7'' 15' 4'' 12' 11''
18 (43) 16 22' 6'' 19' 8'' 16' 7'' 17' 10'' 15' 7'' 13' 2'' 15' 12'' 13' 11'' 11' 9'' 24 19' 8'' 17' 2'' 14' 6'' 15' 7'' 13' 8'' 11' 6'' 13' 4'' 12' 2'' 10' 3'' 12 26' 8'' 23' 4'' 19' 8'' 21' 2'' 18' 6'' 15' 7'' 18' 11'' 16' 6'' 13' 11''
3.625 16 (54) 16 24' 3'' 21' 2'' 17' 10'' 19' 3'' 16' 10'' 14' 2'' 17' 2'' 15' 0'' 12' 8'' 24 21' 2'' 18' 6'' 15' 7'' 16' 10'' 14' 8'' 12' 5'' 15' 0'' 13' 2'' 11' 1'' 12 28' 10'' 25' 2'' 21' 3'' 22' 11'' 19' 12'' 16' 10'' 20' 6'' 17' 10'' 15' 1''
14 (68) 16 26' 2'' 22' 11'' 19' 4'' 20' 10'' 18' 2'' 15' 4'' 18' 7'' 16' 3'' 13' 8'' 24 22' 11'' 19' 12'' 16' 10'' 18' 2'' 15' 10'' 13' 5'' 16' 3'' 14' 2'' 11' 12'' 12 32' 1'' 28' 0'' 23' 8'' 25' 6'' 22' 3'' 18' 9'' 22' 9'' 19' 11'' 16' 9''
12 (97) 16 29' 2'' 25' 6'' 21' 6'' 23' 2'' 20' 3'' 17' 1'' 20' 8'' 18' 1'' 15' 3'' 24 25' 6'' 22' 3'' 18' 9'' 20' 3'' 17' 8'' 14' 11'' 18' 1'' 15' 9'' 13' 4'' 12 33' 4'' 29' 1'' 24' 7'' 26' 5'' 23' 1'' 19' 6'' 22' 3'' 20' 8'' 17' 5''
20 (33) 16 30' 3'' 26' 5'' 22' 4'' 24' 0'' 20' 12'' 17' 8'' 19' 3'' 18' 9'' 15' 10'' 24 26' 5'' 23' 1'' 19' 6'' 20' 12'' 18' 4'' 15' 6'' 15' 9'' * 15' 9'' * 13' 10'' *12 36' 9'' 32' 2'' 27' 1'' 29' 2'' 25' 6'' 21' 6'' 26' 1'' 22' 10'' 19' 3''
18 (43) 16 33' 5'' 29' 2'' 24' 8'' 26' 6'' 23' 2'' 19' 7'' 23' 9'' 20' 9'' 17' 6'' 24 29' 2'' 25' 6'' 21' 6'' 23' 2'' 20' 3'' 17' 1'' 19' 5'' 18' 1'' 15' 3'' 12 39' 8'' 34' 8'' 29' 3'' 31' 6'' 27' 6'' 23' 2'' 28' 2'' 24' 7'' 20' 9''
6 16 (54) 16 36' 0'' 31' 6'' 26' 6'' 28' 7'' 24' 12'' 21' 1'' 25' 7'' 22' 4'' 18' 10'' 24 31' 6'' 27' 6'' 23' 2'' 24' 12'' 21' 10'' 18' 5'' 22' 4'' 19' 6'' 16' 5'' 12 42' 11'' 37' 6'' 31' 7'' 34' 1'' 29' 9'' 25' 1'' 30' 5'' 26' 7'' 22' 5''
14 (68) 16 38' 12'' 34' 1'' 28' 9'' 30' 11'' 27' 0'' 22' 10'' 27' 8'' 24' 2'' 20' 5'' 24 34' 1'' 29' 9'' 25' 1'' 27' 0'' 23' 7'' 19' 11'' 24' 2'' 21' 1'' 17' 10'' 12 47' 11'' 41' 10'' 35' 3'' 38' 0'' 33' 3'' 28' 0'' 33' 12'' 29' 8'' 25' 0''
12 (97) 16 43' 6'' 38' 0'' 32' 1'' 34' 6'' 30' 2'' 25' 5'' 30' 10'' 26' 12'' 22' 9'' 24 38' 0'' 33' 3'' 28' 0'' 30' 2'' 26' 4'' 22' 3'' 26' 12'' 23' 7'' 19' 10''
HDS® Limiting Heights
Table Notes
1) Except for wind loads less than 15 psf, values are based on deflection calculations using 70% of components and cladding wind load. This is per IBC 2002 and the AISI Standard for CFS Wall Stud Design 2004.
2) Members are checked for simple span moment and deflection at mid-span, and end shear.3) Limiting heights marked with an asterisk (*) fail in web crippling per the AISI Standard for CFS Wall Stud Design 2004.
A web stiffener or connection that is not susceptible to web crippling is required.4) Check with your local Dietrich plant to verify if HDS members can be supplied in the length required for your job.
Some Dietrich plants can supply HDS members only in 20' maximum lengths.
Patent Pending
84 The place to stop…before the building starts! SMrequest a quote online @
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:06 AM Page 84
For more information or to contact a sales representative, see page 3
HD
S®
Framing System
HDS Stud WindloadMember Gauge Spacing 25 psf 30 psf 35 psf
Size (mils) (in) 240 360 600 240 360 600 240 360 60012 13' 11'' 12' 10'' 10' 10'' 12' 8'' 12' 1'' 10' 2'' 11' 9'' 11' 6'' 9' 8''
20 (33) 16 12' 0'' 11' 8'' 9' 10'' 10' 12'' 10' 12'' 9' 3'' 10' 2'' 10' 2'' 8' 10'' 24 9' 10'' 9' 10'' 8' 7'' 8' 12'' 8' 12'' 8' 1'' 8' 4'' * 8' 4'' * 7' 8'' 12 16' 4'' 14' 3'' 12' 0'' 15' 4'' 13' 5'' 11' 4'' 14' 3'' 12' 9'' 10' 9''
18 (43) 16 14' 7'' 12' 11'' 10' 11'' 13' 4'' 12' 2'' 10' 3'' 12' 4'' 11' 7'' 9' 9'' 24 11' 11'' 11' 4'' 9' 7'' 10' 11'' 10' 8'' 8' 12'' 10' 1'' 10' 1'' 8' 6'' 12 17' 7'' 15' 4'' 12' 11'' 16' 6'' 14' 5'' 12' 2'' 15' 9'' 13' 9'' 11' 7''
3.625 16 (54) 16 15' 12'' 13' 11'' 11' 9'' 15' 0'' 13' 2'' 11' 1'' 14' 3'' 12' 6'' 10' 6'' 24 13' 11'' 12' 2'' 10' 3'' 13' 2'' 11' 6'' 9' 8'' 12' 6'' 10' 11'' 9' 2'' 12 18' 12'' 16' 7'' 13' 12'' 17' 10'' 15' 7'' 13' 2'' 16' 12'' 14' 10'' 12' 6''
14 (68) 16 17' 3'' 15' 1'' 12' 9'' 16' 3'' 14' 2'' 11' 12'' 15' 5'' 13' 6'' 11' 4'' 24 15' 1'' 13' 2'' 11' 1'' 14' 2'' 12' 5'' 10' 5'' 13' 6'' 11' 9'' 9' 11'' 12 21' 2'' 18' 6'' 15' 7'' 19' 11'' 17' 4'' 14' 8'' 18' 11'' 16' 6'' 13' 11''
12 (97) 16 19' 2'' 16' 9'' 14' 2'' 18' 1'' 15' 9'' 13' 4'' 17' 2'' 14' 12'' 12' 8'' 24 16' 9'' 14' 8'' 12' 4'' 15' 9'' 13' 9'' 11' 8'' 14' 12'' 13' 1'' 11' 1'' 12 19' 11'' 19' 2'' 16' 2'' 18' 2'' * 18' 1'' * 15' 3'' 16' 10'' * 16' 10'' * 14' 5''
20 (33) 16 17' 3'' * 17' 3'' * 14' 8'' 15' 9'' * 15' 9'' * 13' 10'' * 14' 7'' * 14' 7'' * 13' 2'' *24 14' 1'' * 14' 1'' * 12' 10'' * 12' 10'' * 12' 10'' * 12' 1'' * 11' 11'' * 11' 11'' * 11' 6'' *12 24' 3'' 21' 2'' 17' 10'' 22' 5'' 19' 11'' 16' 10'' 20' 9'' 18' 11'' 15' 11''
18 (43) 16 21' 3'' 19' 3'' 16' 3'' 19' 5'' 18' 1'' 15' 3'' 17' 11'' 17' 2'' 14' 6'' 24 17' 4'' * 16' 10'' 14' 2'' 15' 10'' * 15' 10'' * 13' 4'' 14' 8'' * 14' 8'' * 12' 8'' *12 26' 1'' 22' 10'' 19' 3'' 24' 7'' 21' 6'' 18' 1'' 23' 4'' 20' 5'' 17' 2''
6 16 (54) 16 23' 9'' 20' 9'' 17' 6'' 22' 4'' 19' 6'' 16' 5'' 21' 2'' 18' 6'' 15' 8'' 24 20' 9'' 18' 1'' 15' 3'' 19' 6'' 17' 0'' 14' 4'' 18' 6'' 16' 2'' 13' 8'' 12 28' 3'' 24' 8'' 20' 10'' 26' 7'' 23' 3'' 19' 7'' 25' 3'' 22' 1'' 18' 7''
14 (68) 16 25' 8'' 22' 5'' 18' 11'' 24' 2'' 21' 1'' 17' 10'' 22' 11'' 20' 1'' 16' 11'' 24 22' 5'' 19' 7'' 16' 6'' 21' 1'' 18' 5'' 15' 7'' 20' 1'' 17' 6'' 14' 9'' 12 31' 7'' 27' 7'' 23' 3'' 29' 8'' 25' 11'' 21' 10'' 28' 2'' 24' 8'' 20' 9''
12 (97) 16 28' 8'' 25' 0'' 21' 1'' 26' 12'' 23' 7'' 19' 10'' 25' 7'' 22' 5'' 18' 11'' 24 25' 0'' 21' 10'' 18' 5'' 23' 7'' 20' 7'' 17' 4'' 22' 5'' 19' 7'' 16' 6''
HDS® Limiting Heights
Table Notes
1) Except for wind loads less than 15 psf, values are based on deflection calculations using 70% of components and cladding wind load. This is per IBC 2002 and the AISI Standard for CFS Wall Stud Design 2004.
2) Members are checked for simple span moment and deflection at mid-span, and end shear.3) Limiting heights marked with an asterisk (*) fail in web crippling per the AISI Standard for CFS Wall Stud Design 2004.
A web stiffener or connection that is not susceptible to web crippling is required.4) Check with your local Dietrich plant to verify if HDS members can be supplied in the length required for your job.
Some Dietrich plants can supply HDS members only in 20' maximum lengths.
Patent Pending
Headers, Jambs, Posts
85
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:06 AM Page 85
86 The place to stop…before the building starts! SMrequest a quote online @
ProX
Hea
der®
Fram
ing
Syst
em
The Brady ProX Header System has undergone stringent laboratory testing. ProX complies with all industry standard Light Gauge Metal Stud Framing ASTM criteria. Section geometry and material strengths were modeled in CFS Version 4.1, a cold-formed steel design and analysis software. Calculated in accordance 2001 addition of the American Iron and Steel Institute (AISI) Specifications for Design of Cold Formed Structural Members.
Dietrich / ProX SSMA Nomenclature Put the ProX Header System to work on your next project.
Brady ProX has become an industry standard for all wall openings.The ProX is ideal for all types of door, window, shaftwall, HVAC, and ventilation openings. This simple system has application to a wide range of openings and can carry greater loads with less steel. The contractor community prefers the ProX system over traditional built-up headers.
Typical Interior Wall Openings
on
r
Double DoorSingle Door
ProX Clip - Available Only in 16 gauge (54 mil.) 50 ksi material Patent Number 6,799,408 & 7,178,304
362 X 425 3.625” 92.1 4.25” 107.95 362 XT 162 3.464” 88 1.625” 41.3 362Clip-54 1.50” 38.1
400 X 425 4.000” 101.6 4.25” 107.95 400 XT 162 3.839” 97.5 1.625” 41.3 400Clip-54 1.50” 38.1
600 X 425 6.000” 152.4 4.25” 107.95 600 XT 162 5.839” 148.3 1.625” 41.3 600Clip-54 1.50” 38.1
800 X 425 8.000” 203.2 4.25” 107.95 800 XT 162 7.839” 199.1 1.625” 41.3 800Clip-54 1.50” 38.1
Member Types and Available Sizes
WidthProX Header (Outer Member) - OD ProX Insert (Insert Member) - OD
inches (mm) inches (mm)inches (mm) inches (mm) inches (mm)Height Width Height Leg Length
ProX Clip*Member Type Member Type Member Type
®
Building a Better Way.
Member Types and Available Sizes
Detail Dimensions
7.8395.8393.8393.4641.899
1.8993.6254.0006.0008.000
1.625
4.25
Single Piece Header
Header InsertOptional
Two Piece Header
Internal Connection Clip
SSMA - 400X425-33 SSMA - 400XT162-33 SSMA - 400XTC425-33 SSMA - 400Clip-150-54 Dietrich - 400PXH-33 Dietrich - 400PXT-33 Dietrich - Order by Piece Dietrich - 400XTC-54
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:06 AM Page 86
87For more information or to contact a sales representative, see page 3
Headers, Jambs, PostsProX H
eader ®Fram
ing System
®
The Brady ProX Header System consists of only three components: ProX Header, ProX Insert, ProX Clip
NO Welding Required
Built-Up Header
ProX Header w/ Insert
ProX Header
Built-Up Header
www.ProXHeader.com
ProX Header @ 1hr Walls ProX Header @ 2hr Walls
0’-0” to 4’-3” 4’-4” to 6’-3” 6’-4” to 8’-3” 8’-4” to 10’-3”
WALLHEIGHT
400X425- 33 400X425- 43 400X425- 54 400X425- 68 400X425- 33 400X425- 54 400X425- 68 400XTC425- 68
400X425- 33 400X425- 54 400X425- 54 400X425- 68 400X425- 43 400X425- 54 400XTC425- 54 -
400X425- 33 400X425- 54 400X425- 68 400XTC425- 54 400X425- 43 400X425- 68 400XTC425- 68 -
0’-0” to 14’-0”
14’-1” to 16’-0”
16’-1” to 18’-0”
Interior Header Schedule -L/240- Walls w/ (1) Layer Gypsum Interior Header Schedule -L/240- Walls w/ (2) Layer Gypsum
MAX Opening Width MAX Opening Width 0’-0” to 4’-3” 4’-4” to 6’-3” 6’-4” to 8’-3” 8’-4” to 10’-3”
NOTE: Charts shown in 4 inch wide walls for 3-5/8, 6, 8 inch wide wall visit www.ProXHeader.com
On-Line Member Selector @ www.ProXHeader.com ProX Header selection and submittal builder is easy. Simply go to www.proxheader.com and launch the interactive Member Selector. Input your project specific load data and requirements, the Member Selector / submittal builder will output a engineered header with a complete AIA formatted submittal package.• Complete Engineer Submittal Packages • Complete Architectural / Engineering drawings
Material Specifications ProX Header Gauge: 20 gauge (33 mils) 18 gauge (43 mils) 16 gauge (54mils) 14 gauge (68 mils)Design Thickness: 0.0346 inches (0.879 mm) 0.0451 inches (1.142 mm) 0.0566 inches (1.438 mm) 0.0713 inches (1.811 mm)Coating: G 60(Z180) hot- dipped galvanized coating or equivalent Yield Strength: 33 ksi (230MPa) or 50 ksi (340MPa)ASTM: A653 / A653M
Installation The ProX Header recessed channels and the ProX Clips’ offset tabs enable the ProX Header to “SNAP” and HOLD ITSELF IN PLACE dur-ing installation. After instal-lation, all screw connections remain flush and ready for a smooth drywall finish. • Minimal Screws, No Welds
Applications / Benefits The Brady ProX Header system provides a direct solution to the many problems associated with traditional headers that have troubled architects, engineers, contractors and inspectors for decades. ProX Header is a superior and cost effective alternative to the limited span capabilities of a single track and the excessive build-up of traditional box headers. The ProX Header is designed for all interior and exterior door and window wall openings in the 3 to 12 foot wide range.• ProX Header offers a standard single piece design • ProX installs flush leaving a smooth finish• ProX installs quickly and consistently • ProX saves time and money
St. Johns Hospital - SantaMonica, CaliforniaPhoto Courtesy of Performance Contracting, Inc.
ProX InsertOptional
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:06 AM Page 87
88 The place to stop…before the building starts! SMrequest a quote online @
L-H
eade
r (L
HD
R)
Preformed L-header thatslides into place quickly.■ Substantial labor savings.
■ Lightweight and easy to handle.
■ Available in stock and custom lengths.
Dietrich L-Headers are prefabricated light-gauge 90˚ L-sectionsthat are used in load-bearing wall framing. L-headers slide easilyinto place and eliminate the labor-intensive process of built-upfield-assembled headers. L-headers may not work in all loadingsituations. Proper loading comparisons should be examined,especially when considering uplift loads. L-headers may beinstalled as single, one header one side, or double, two headers,one on both sides.
L-Header
DMF Leg Length Thickness WeightProduct Inches mm Gauge Mils Design Thickness lbs/ft kg/mCode Inches mm
1-1/2 x 6 38.1 x 152 18 43 0.0451 1.146 1.161 1.7221-1/2 x 6 38.1 x 152 16 54 0.0566 1.438 1.457 2.1611-1/2 x 6 38.1 x 152 14 68 0.0713 1.811 1.835 2.7221-1/2 x 8 38.1 x 203 18 43 0.0451 1.146 1.470 2.181
LHDR 1-1/2 x 8 38.1 x 203 16 54 0.0566 1.438 1.845 2.7391-1/2 x 8 38.1 x 203 14 68 0.0713 1.811 2.325 3.4501-1/2 x 10 38.1 x 254 18 43 0.0451 1.146 1.780 2.6401-1/2 x 10 38.1 x 254 16 54 0.0566 1.438 2.234 3.3161-1/2 x 10 38.1 x 254 14 68 0.0713 1.811 2.814 4.175
L-Header (LHDR)
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:06 AM Page 88
89For more information or to contact a sales representative, see page 3
Exterior Light-Gauge Load-Bearing Wall HeadersTradeReady
®(TD
HA/TD
HB) Load-Bearing H
eader
Preformed U-shaped headerthat slides easily over wallassembly and providesmaximum carrying capacity.■ Huge labor savings.
■ Easy and fast installation.
■ Pre-engineered for most door or window openings.
■ Easily insulated after installation.
The TradeReady® load-bearing one-piece header drastically reduceslabor costs when compared to standard box beam headersconstructed with C-shaped members. TradeReady® headers are pre-engineered to fit standard door and window openings. Just slip theTradeReady® header over the top track, screw to the jamb studs andyour header is complete. These headers have great load-distributionqualities and enable access for insulation after the framing iscompleted.
U.S. Patent No. 5,689,922 and other foreign patents.
TradeReady® Header
DMF Wall Leg Thickness WeightProduct Stud Size Length Gauge Mils Design Thickness lbs/ft kg/mCode Inches mm Inches mm Inches mm
TDHA3-5/8 92.1 8 203.2
14 68 0.0713 1.8114.802 7.127
6 152.4 8 203.2 5.383 7.990
TDHB3-5/8 92.1 12 304.8
14 68 0.0713 1.8116.760 10.033
6 152.4 12 304.8 7.341 10.896
TradeReady® Header (TDHA/TDHB)
Standard lengths are 82" and 118".Custom sizes available on request.
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:06 AM Page 89
Back
-to-B
ack
(C-S
tuds
) (T
S-Tr
ack)
(S-
Serie
s™C
lips)
Back-to-back or I-beam headers,consist of two “C”sections with the websscrewed back to back.The header takes theshape of an I. Headersare attached to thejamb stud withEasyClip™ SupportClips (S-Series™). Jackstuds are usually usedto provide additionalsupport. Manycontractors prefer thismethod of building headers because they can be insulatedafter assembly. This type of header is sold as componentsand must be field fabricated. When C-studs are used inheader applications, they should be ordered as unpunched.
Traditional, field-fabricated,built-up back-to-back C-Stud Header used todistribute loads above doorand window openings.■ Assembled using traditional C-Stud and track
members.
■ I-shape permits easy installation of web stiffenerswhen required.
■ Can be insulated after installation.
I-Header
The place to stop…before the building starts! SMrequest a quote online @90
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:06 AM Page 90
For more information or to contact a sales representative, see page 3
Exterior Light-Gauge Load-Bearing Wall Headers
Traditional field-fabricatedbuilt-up box beam headerused to distribute loadsabove door and windowopenings.■ Field assembled using traditional C-Stud
and track members.
■ Labor intensive assembly.
■ Must be insulated prior to installation.
■ Provides surface for sheathing attachment.
Box beam headers are field or shop assembled bypositioning two C-Stud sections with the open side of thewebs or “C”s facing each other. The “C”s are capped with atop and bottom track and positioned overthe door or window opening. Forlighter load applications, a singlepiece of stud and track can benested to form a cappedheader. In most cases,the connection at thejamb is made bynesting the boxedheader into a track.Usually jack studsare used to add additional headersupport. Box beamheaders must beinsulated at time offabrication. This type ofheader is sold ascomponents and mustbe field fabricated.When C-Studs are usedin header applications,they should be ordered as unpunched.
Boxed Header
Capped Header
Boxed Header and C
apped Header (C
-Studs) (TS-Track) (S-Series™
Clips)
91
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:07 AM Page 91
92 The place to stop…before the building starts! SMrequest a quote online @
Fast
Clip
™(F
CSC
)
Provides the fastest and easiestattachment forcurtain-wall framing.■ Vertical movement up to 3”
(1-1/2” up and down).
■ Rapid, one-piece installation.
■ Proprietary screws provide frictionlessslip connection.
■ Available with 3-1/2” and 5-1/2” legs.
■ Stiffened corners result in superior design values.
■ Embossed fastening patterns to ensureaccurate placement of fasteners.
■ 14-gauge, G 90, 50 ksi steel.
OvernightDelivery!
Available for
Fast Clip™ (3-1/2")Fast Clip™ (5-1/2")
ProprietaryScrew
DMF Thickness Size Weight/Piece Packaging*Product Gauge Mils Design Thickness Inches mm lbs kg Pcs/Code Inches mm Box
FCSC 14 68 0.0713 1.8111-1/2 x 3-1/2 38.1 x 88.9
0.550 0.249 25x 4-1/2 x 114.5
FCSC 14 68 0.0713 1.8111-1/2 x 5-1/2 38.1 x 139.7
0.636 0.287 25x 4-1/2 x 114.5
*Includes 55 proprietary shoulder screws per box.
Fast Clip™ (FCSC) Deflection Clips
Dietrich Fast Clip™ deflection clips are used to attachexterior curtain-wall studs to the building structureand provide for vertical building movementindependent of the cold-formed steel framing. The 3-1/2" leg Fast Clip™ is used in minimal standoffconditions. The 5-1/2" leg Fast Clip™ is used for widerstandoff conditions and wider web framing members.A Dietrich Fast Clip™ deflection clip installs quicklywith welds, screws or powder-actuated fasteners andprovides adjustable standoff to ensure a plumb wallplane. Proprietary screws are provided with each clipto ensure friction-free sliding. Each clip is alsoembossed with fastening patterns to ensure accurateplacement of fasteners.
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:07 AM Page 92
93For more information or to contact a sales representative, see page 3
Exterior Light-Gauge Connections/Accessories for Deflection/Slip Connections
■ Use for all medium and large standoff conditions.
■ Eliminates shims and scabs.
■ Vertical movement up to 3" (1-1/2" up and 1-1/2"down).
■ Specially designed to simplify welding installation
■ Fast, one-piece universal installation. No left or right handed clips.
■ FastClip™ Deflection Screws(included) provide frictionless slip connections.
■ Embossed fastening pattern to ensureaccurate placement of fasteners.
■ Custom and longer lengths available
Product DimensionsThe 8" (203.2mm) EXTENDED FastClip™ is 1-7/8" x 8" x 4-3/4"(47.6mm x 203.2mm x 120.6mm) long.The 10" (254.0mm) EXTENDED FastClip™ is 1-7/8" x 10" x 4-3/4"(47.6mm x 254.0mm x 120.6mm) long.The 12" (304.8mm) EXTENDED FastClip™ is 1-7/8" x 12” x 4-3/4"(47.6mm x 304.8mm x 120.6mm) long.
Material SpecificationsGauge: 14 gauge (68 mils)Design Thickness: 0.0713 inches (1.811mm)Coating: G90 (Z275) hot-dipped galvanized coating.Yield Strength: Mill-certified SS Grade 50 ksi (340 MPa)ASTM: A 653/A 653M
InstallationConnections to the building can be made with screws,welds powder-actuated fasteners or drill-in concreteanchors. Mechanical fasteners shall be located on theembossed marks given on the scored line of the 1.5" flange.Three FastClip™ Deflection Screws are used to attach theclip to the cold-formed steel framing. Screws shall bedriven through the slotted holes and positioned to allowfor the appropriate building deflection.
U.S. Patent No. 6, 688, 069
Dietrich EXTENDED FastClip™ Slide Clip™ deflection clipsare used to attach exterior curtain wall studs to thebuilding structure and provide for vertical buildingmovement independent of the cold-formed steel framing.The clips are available in standard lengths of 8”, 10” and12” and are ideal for medium to larger standoff conditions.EXTENDED FastClip™ deflection clips install quickly withscrews, welds or powder-actuated fasteners, and provideadjustable standoff to ensure a plumb wall plane. FastClip™
Deflection Screws are provided with each clip to ensurefriction-free sliding. Each clip is also embossed withfastening patterns to ensure accurate placement offasteners.
Alternative ProductsFast Strut™
FastClip™
DeflectionScrew
8", 10" or 12"
4-3/4"
1/2"
1-7/8"
The EXTENDED FastClip™ slide clip curtain wall deflectionconnector provides for vertical building movement up to3” (76.2mm) and is commonly used for large standoff conditions.
EXTENDED FastClip™
NEWITEM
EXTEND
ED FastC
lip™
Slide Clip
™ (FC
EC)
DMF Thickness Size Weight/Piece Packaging*Product Gauge Mils Design Thickness Inches mm lbs kg Pcs/Code Inches mm Box
FCEC 14 68 0.0713 1.8111-7/8 x 8 47.6 x 203.2
1.092 0.495 25x 4-3/4 x 120.6
FCEC 14 68 0.0713 1.8111-7/8 x 10 47.6 x 254.0
1.366 0.619 25x 4-3/4 x 120.6
FCEC 14 68 0.0713 1.8111-7/8 x 12 47.6 x 304.8
1.639 0.743 25x 4-3/4 x 120.6
Includes 80 FastClip™ deflection screws per box.
EXTENDED FastClip™ (FCEC) Deflection Clips
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:07 AM Page 93
94 The place to stop…before the building starts! SMrequest a quote online @
Fast
Top
®C
lip (
FTC
3/FT
C5)
Head-of-wall, exterior curtain-walldeflection clips for vertical buildingmovement.■ An excellent alternative to deflection track, slip-track
and track-over-track.
■ Fast Clip™ slip technology.
■ Available in 3” and 5” widths.
■ Attaches within the wall cavity.
■ Proprietary screws provide frictionless slip connections.
■ Embossed fastening patterns to ensure accurateplacement of fasteners.
■ 14-gauge, G 90, 50 ksi steel.
The Dietrich Fast Top™ clip is used in head-of-wall deflectionconditions for in-fill curtain wall assemblies to provide for vertical wallmovement. These clips are used in place of or in combination withdeflection track and track-over-track assemblies. They also make apositive attachment and do not require bridging or bracing for thedeflection system. The Fast Top™ deflection clip attaches to theunderside of structural members, concrete decks or floor assemblies.Studs must be cut less than full height to enable vertical movement upto 2-1/2" (1-1/4" up and down). Fast Top™ deflection clips quicklyinstall with welds, screws or powder actuated fasteners. Proprietaryscrews ensure frictionless deflection. These clips are also embossedwith fastening patterns to ensure accurate placement of fasteners.
Patent Pending.
DMF Thickness Size Weight/Piece Packaging*Product Gauge Mils Design Thickness Inches mm lbs kg Pcs/Code Inches mm BoxFTC3 14 68 0.0713 1.811 4 x 1-1/2 x 3-1/4 101 x 38.1 x 82.6 0.410 0.186 25FTC5 14 68 0.0713 1.811 4 x 1-1/2 x 4-3/4 101 x 38.1 x 120 0.610 0.277 30
*Includes 110 proprietary shoulder screws per box.
Fast Top™ Clip (FTC3 and FTC5)
OvernightDelivery!
Available for
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:07 AM Page 94
95For more information or to contact a sales representative, see page 3
Exterior Light-Gauge Connections/Accessories for Deflection/Slip Connections
Superior curtain-wallfastener that allows up to a 7-1/2" standoff.■ Use for all wide standoff conditions.
■ Fast, one-piece universal installation.
■ Proprietary screws provide frictionless slip connections.
■ Vertical movement up to 2-1/2” (1-1/4” up and down).
■ Embossed fastening pattern to ensureaccurate placement of fasteners.
■ 14-gauge, G 90, 50 ksi steel.
DMF Thickness Size Weight/Piece Packaging*Product Gauge Mils Design Thickness Inches mm lbs kg Pcs/Code Inches mm BoxFS12 14 68 0.0713 1.81 4 x 2 x 12-1/4 101 x 50.8 x 311 1.560 0.706 10FS15 14 68 0.0713 1.81 4 x 2 x 15-1/4 101 x 50.8 x 387 1.970 0.891 10
Includes 55 proprietary shoulder screws per box.Custom lengths are available up to 24".
The Dietrich Fast Strut™ curtain-wall connector employs similar Fast Clip™
technology for curtain-wall stud attachment and is commonly used when widestand-off conditions exist. Fast Strut™ products are available in standard lengths of 12-1/4" and 15-1/4" and custom lengths of up to 24" long to allow framingattachment well beyond the perimeter of the structural steel. Struts are attachedto the underside of structural members with screws, welds, or powder-actuatedfasteners. Studs are plumbed and secured with propriety screws for friction-freedeflection. Each clip is also embossed with fastening patterns to ensure accurateplacement of fasteners.
Patent pending.
Fast Strut™ 12
Fast Strut™ 15
ProprietaryScrew
Fast Strut™ 12 and 15 (FS12/FS15) Curtain-Wall Connector
OvernightDelivery!
Available for
Fast Strut ™(FS12/FS15)
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:07 AM Page 95
96 The place to stop…before the building starts! SMrequest a quote online @
Slid
e C
lip (
SD)
Edge-of-slab deflection clip forcurtain wall framing.■ First-generation low-cost deflection clip.
■ Offset for easier welding.
■ Requires additional framing components for horizontal adjustment.
■ 12- or 14-gauge, G 90, 50 ksi steel.
Dietrich slide clips are used to attach exteriorcurtain-wall studs to the building structure andprovide for vertical building movementindependent of the cold-formed steel framing.Slide clips are used in by-pass situations and arenormally welded or otherwise fastened to thevertical leg of a structural angle at the floor or roofedge. Normally a stand-off exists between thestructural angle and the inside flange of thecurtain-wall stud. This will require the installationof an extra stud piece to bridge the stand-off. Inorder to avoid the extra installation costs, DietrichFast Clip™ products are recommended in place ofthe SD.
Slide Clip SD
DMF Thickness Size Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm lbs kg Pcs/Code Inches mm BoxSD 14 68 0.0713 1.811 2 3/8 x 5 60.3 x 127 0.600 0.271 50SD 12 97 0.1017 2.583 2 3/8 x 5 60.3 x 127 0.840 0.380 50
Slide Clip (SD)
OvernightDelivery!
Available for
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:07 AM Page 96
97For more information or to contact a sales representative, see page 3
Exterior Light-Gauge Connections/Accessories for Deflection/Slip ConnectionsQ
uickClip
™(Q
C-Series
™)
Vertical Slide Clip that providesup to 3" of horizontal standoff.■ Quick installation—twist and fasten.
■ Horizontal stand-off up to 3”.
■ One-piece for right- or left-handed attachment.
■ Accommodates 1-5/8” and 2” flanges.
■ Standard 10-gauge, 50 ksi steel. QuickClip™
QuickClip™ vertical slide clips are used to attach exteriorcurtain-wall studs to the building structure and providefor vertical building movement independent of the cold-formed steel framing. A QuickClip™ slide clipprovides variable standoff and eliminates the need forshims or additional framing components. TheQuickClip™ slide clip simply twists into place and fastensto the floor/ceiling beam. The clips restrict lateralmovement, but enable the curtain-wall system to movevertically.
U.S. Patent No. 5, 836, 133 of B&D Industries
DMF Thickness Stud Weight/Piece PackagingProduct Gauge Mils Design Thickness Width lbs kg Pcs/Code Inches mm Inches BucketQC3 10 118 0.1242 3.155 3-5/8 0.940 0.426 50QC4 10 118 0.1242 3.155 4 1.160 0.526 50QC6 10 118 0.1242 3.155 6 1.460 0.662 50QC8 10 118 0.1242 3.155 8 1.770 0.803 40
QuickClip™ (QC-Series™)
OvernightDelivery!
Available for
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:07 AM Page 97
98 The place to stop…before the building starts! SMrequest a quote online @
Uni
-Clip
™(U
CEC
)
Universal framing clip used fornumerous rigid connections andconditions, including two axisloading, shear and tension.■ Designed to transfer large horizontal and vertical loads.
■ Universal multi-application connector.
■ Embossed fastening patterns to ensure accurateplacement of fasteners.
■ 14-gauge, G 90, 50 ksi steel.
Dietrich’s Uni-Clip™ framing clip is auniversal framing clip used to attach and support numerous rigid framingconditions. The Uni-Clip™ framing clip hasstiffened corners that provide superiordesign values, and they are installed easilywith welds, screws or powder-actuatedfasteners. This clip is ideal for most rigidconnections including shear, tension andtwo-axis loading.
Patent Pending.
Uni-Clip™
DMF Thickness Size Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm lbs kg Pcs/Code Inches mm BoxUCEC 14 68 0.0713 1.811 3-1/2 x 1-1/2 x 4-1/2 88.9 x 38.1 x 114 0.440 0.199 25
Uni-Clip™ (UCEC) Framing Clips
OvernightDelivery!
Available for
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:07 AM Page 98
99For more information or to contact a sales representative, see page 3
Exterior Light-Gauge Connections/Accessories for Rigid ConnectionsEasyC
lip™
Support Clips (E-Series
™)
Long leg to accommodate greaterstandoff for rigid connections■ 4” leg accommodates large stand-off.
■ Lengths available in 3”, 5”, 7”, 9” and 11”.
■ Available in 16, 14 and 12 gauge.
■ Prepunched for faster and accurate fastener attachment.
■ G 90, 50 ksi steel.
Dietrich EasyClip™ E-Series™ support clips are used for rigidstand-off connections. The 4" wide leg provides extra length toachieve stand-off connections up to 3". The EasyClip™ E-Series™
clips are commonly used in bypass wall conditions, solidblocking attachments in joist framing and to secure rafterframing to the primary structure. These clips are prepunchedfor faster and more accurate fastener placement.
EasyClip™ Support Clip(E-Series™)
DMF Thickness Size Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm lbs kg Pcs/Code Inches mm BucketE543 16 54 0.0566 1.438 4 x 1-1/2 x 3 101 x 38.1 x 76.2 0.270 0.122 100E545 16 54 0.0566 1.438 4 x 1-1/2 x 5 101 x 38.1 x 127 0.440 0.200 100E547 16 54 0.0566 1.438 4 x 1-1/2 x 7 101 x 38.1 x 178 0.620 0.281 100E549 16 54 0.0566 1.438 4 x 1-1/2 x 9 101 x 38.1 x 229 0.800 0.363 50E541 16 54 0.0566 1.438 4 x 1-1/2 x 11 101 x 38.1 x 279 0.970 0.440 50E683 14 68 0.0713 1.811 4 x 1-1/2 x 3 101 x 38.1 x 76.2 0.330 0.150 100E685 14 68 0.0713 1.811 4 x 1-1/2 x 5 101 x 38.1 x 127 0.550 0.249 100E687 14 68 0.0713 1.811 4 x 1-1/2 x 7 101 x 38.1 x 178 0.770 0.349 80E689 14 68 0.0713 1.811 4 x 1-1/2 x 9 101 x 38.1 x 229 0.990 0.449 50E681 14 68 0.0713 1.811 4 x 1-1/2 x 11 101 x 38.1 x 279 1.220 0.553 50E973 12 97 0.1017 2.583 4 x 1-1/2 x 3 101 x 38.1 x 76.2 0.470 0.213 50E975 12 97 0.1017 2.583 4 x 1-1/2 x 5 101 x 38.1 x 127 0.780 0.354 50E977 12 97 0.1017 2.583 4 x 1-1/2 x 7 101 x 38.1 x 178 1.090 0.494 50E979 12 97 0.1017 2.583 4 x 1-1/2 x 9 101 x 38.1 x 229 1.410 0.640 50E971 12 97 0.1017 2.583 4 x 1-1/2 x 11 101 x 38.1 x 279 1.720 0.780 40
EasyClip™ Support Clips (E-Series™)
OvernightDelivery!
Available for
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:07 AM Page 99
100 The place to stop…before the building starts! SMrequest a quote online @
Easy
Clip
™Su
ppor
t Clip
s (S
-Ser
ies™
)
Used in any rigid connection applicationnot requiring a long leg.■ 1-1/2” x 1-1/2” legs.
■ Lengths available in 3”, 5”, 7”, 9” and 11”.
■ Available in 16, 14 and 12 gauge.
■ Prepunched for faster and more accurate fastener placement.
■ G 90, 50 ksi steel.
Dietrich EasyClip™ S-Series™
support clips are used forrigid connections in windowand door framing. These clipsare also used in joist, bypassor other miscellaneousconnections to secure oneframing member to anotheror to secure framing membersto the structural frame.EasyClip™ S-Series™ clips are prepunched for faster andmore accurate fastenerplacement.
EasyClip™ Support Clip (S-Series™)
DMF Thickness Size Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm lbs kg Pcs/Code Inches mm BucketS543 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 3 38.1 x 38.1 x 76.2 0.140 0.064 400S545 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 5 38.1 x 38.1 x 127 0.240 0.109 200S547 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 7 38.1 x 38.1 x 178 0.340 0.154 100S549 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 9 38.1 x 38.1 x 229 0.430 0.195 100S541 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 11 38.1 x 38.1 x 279 0.530 0.240 100S683 14 68 0.0713 1.811 1-1/2 x 1-1/2 x 3 38.1 x 38.1 x 76.2 0.180 0.082 200S685 14 68 0.0713 1.811 1-1/2 x 1-1/2 x 5 38.1 x 38.1 x 127 0.300 0.136 200S687 14 68 0.0713 1.811 1-1/2 x 1-1/2 x 7 38.1 x 38.1 x 178 0.420 0.191 100S689 14 68 0.0713 1.811 1-1/2 x 1-1/2 x 9 38.1 x 38.1 x 229 0.540 0.245 100S681 14 68 0.0713 1.811 1-1/2 x 1-1/2 x 11 38.1 x 38.1 x 279 0.660 0.299 100S973 12 97 0.1017 2.583 1-1/2 x 1-1/2 x 3 38.1 x 38.1 x 76.2 0.260 0.118 200S975 12 97 0.1017 2.583 1-1/2 x 1-1/2 x 5 38.1 x 38.1 x 127 0.430 0.195 150S977 12 97 0.1017 2.583 1-1/2 x 1-1/2 x 7 38.1 x 38.1 x 178 0.600 0.272 100S979 12 97 0.1017 2.583 1-1/2 x 1-1/2 x 9 38.1 x 38.1 x 229 0.770 0.349 80S971 12 97 0.1017 2.583 1-1/2 x 1-1/2 x 11 38.1 x 38.1 x 279 0.940 0.426 70
EasyClip™ Support Clips (S-Series™)
OvernightDelivery!
Available for
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:07 AM Page 100
101For more information or to contact a sales representative, see page 3
Exterior Light-Gauge Connections/Accessories for Rigid Connections
Dietrich EasyClip™ U-Series™ support clipsare used to secure U-channel to wall studsfor lateral bridging. U-channel is passedthrough the stud knockout and an EasyClip™
U-Series™ clip is screw attached or welded toprovide a rigid connection. EasyClip™
U-Series™ clips are prepunched for faster andmore accurate fastener placement.
Used to secure U-channel (cold rolled channel)to framing member for lateral bridging.■ 1-1/2” x 1-1/2” legs.
■ Lengths available in 3-3/8”, 5-3/4”, 7-3/4” and 9-3/4”.
■ Available in 16, 14 and 12 gauge.
■ Prepunched for faster and more accurate fastener placement.
■ G 90, 50 ksi steel.EasyClip™ Support Clip (U-Series™)
EasyClip
™Support C
lips (U-Series
™)
DMF Thickness Size Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm lbs kg Pcs/Code Inches mm BucketU543 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 3-3/8 38.1 x 38.1 x 85.7 0.16 0.073 400U545 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 5-3/4 38.1 x 38.1 x 146 0.28 0.127 200U547 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 7-3/4 38.1 x 38.1 x 197 0.37 0.168 100U549 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 9-3/4 38.1 x 38.1 x 248 0.47 0.214 100U683 14 68 0.0713 1.811 1-1/2 x 1-1/2 x 3-3/8 38.1 x 38.1 x 85.7 0.20 0.091 200U685 14 68 0.0713 1.811 1-1/2 x 1-1/2 x 5-3/4 38.1 x 38.1 x 146 0.35 0.159 170U687 14 68 0.0713 1.811 1-1/2 x 1-1/2 x 7-3/4 38.1 x 38.1 x 197 0.47 0.214 100U689 14 68 0.0713 1.811 1-1/2 x 1-1/2 x 9-3/4 38.1 x 38.1 x 248 0.59 0.268 100U973 12 97 0.1017 2.583 1-1/2 x 1-1/2 x 3-3/8 38.1 x 38.1 x 85.7 0.29 0.132 200U975 12 97 0.1017 2.583 1-1/2 x 1-1/2 x 5-3/4 38.1 x 38.1 x 146 0.49 0.223 130U977 12 97 0.1017 2.583 1-1/2 x 1-1/2 x 7-3/4 38.1 x 38.1 x 197 0.66 0.300 100U979 12 97 0.1017 2.583 1-1/2 x 1-1/2 x 9-3/4 38.1 x 38.1 x 248 0.83 0.377 80
EasyClip™ Support Clips (U-Series™)
OvernightDelivery!
Available for
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:07 AM Page 101
102 The place to stop…before the building starts! SMrequest a quote online @
Easy
Clip
™Su
ppor
t Clip
s (B
-Ser
ies™
)
Used to secure U-channelin back-to-back framingapplications.■ 1-1/2” x 1-1/2” legs.
■ Available in 3”, 5-1/4”, 7-1/4” and 9-1/4” lengths.
■ Available in 16, 14 and 12 gauge.
■ Pre-punched for faster and more accuratefastener placement.
■ G 90, 50 ksi steel.
Dietrich EasyClip™ B-Series™ support clips are used tosecure U-channel to wall studs in back to back applications. The shorter leg of the B-Series™ clip enables the clip to beinstalled inside the C-shape. The B-Series™ clip can also beused on single studs where the clip is preferred to beinside the C-shape. B-Series™ clips are prepunched forfaster and more accurate fastener placement.
EasyClip™ Support Clip (B-Series™)
DMF Thickness Size Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm lbs kg Pcs/Code Inches mm BucketB543 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 3 38.1 x 38.1 x 76.2 0.15 0.068 400B545 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 5-1/4 38.1 x 38.1 x 133 0.25 0.114 200B547 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 7-1/4 38.1 x 38.1 x 184 0.35 0.159 100B549 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 9-1/4 38.1 x 38.1 x 235 0.45 0.204 100B683 14 68 0.0713 1.811 1-1/2 x 1-1/2 x 3 38.1 x 38.1 x 76.2 0.18 0.082 200B685 14 68 0.0713 1.811 1-1/2 x 1-1/2 x 5-1/4 38.1 x 38.1 x 133 0.32 0.145 170B687 14 68 0.0713 1.811 1-1/2 x 1-1/2 x 7-1/4 38.1 x 38.1 x 184 0.44 0.200 100B689 14 68 0.0713 1.811 1-1/2 x 1-1/2 x 9-1/4 38.1 x 38.1 x 235 0.57 0.259 100B973 12 97 0.1017 2.583 1-1/2 x 1-1/2 x 3 38.1 x 38.1 x 76.2 0.26 0.118 200B975 12 97 0.1017 2.583 1-1/2 x 1-1/2 x 5-1/4 38.1 x 38.1 x 133 0.46 0.209 130B977 12 97 0.1017 2.583 1-1/2 x 1-1/2 x 7-1/4 38.1 x 38.1 x 184 0.63 0.286 100B979 12 97 0.1017 2.583 1-1/2 x 1-1/2 x 9-1/4 38.1 x 38.1 x 235 0.81 0.364 80
EasyClip™ Support Clips (B-Series™)
OvernightDelivery!
Available for
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:07 AM Page 102
103For more information or to contact a sales representative, see page 3
Exterior Light-Gauge Connections/Accessories for Rigid Connections
Used to secure U-channel (cold rolled channel) to framingmember for lateral bridging or to secure one framingmember to another.■ 2” x 2” legs.
■ Available in 3-3/8”, 5-3/4”, 7-3/4” and 9-3/4” lengths.
■ Available in 16, 14 and 12 gauge.
■ Prepunched for faster and more accurate fastener placement.
■ G 90, 50 ksi steel.
EasyClip™ Support Clip (X-Series™)
Dietrich EasyClip™ X-Series™ support clips are usedto secure U-channel to wall studs for lateralbridging. U-channel is passed through the studknockout and an EasyClip™ X-Series™ clip is screwattached or welded to provide a rigid connection.Dietrich EasyClip™ X-Series™ support clips are alsoused to secure one framing member to another orto attach and reinforce headers and sills in doorand window openings. X-Series™ clips areprepunched for faster and more accurate fastenerplacement.
DMF Thickness Size Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm lbs kg Pcs/Code Inches mm BucketX543 16 54 0.0566 1.438 2 x 2 x 3-3/8 50.8 x 50.8 x 85.7 0.194 0.088 200X545 16 54 0.0566 1.438 2 x 2 x 5-3/4 50.8 x 50.8 x 146.0 0.324 0.146 170X547 16 54 0.0566 1.438 2 x 2 x 7-3/4 50.8 x 50.8 x 196.8 0.453 0.205 100X549 16 54 0.0566 1.438 2 x 2 x 9-3/4 50.8 x 50.8 x 247.6 0.583 0.264 100X683 14 68 0.0713 1.811 2 x 2 x 3-3/8 50.8 x 50.8 x 85.7 0.245 0.111 200X685 14 68 0.0713 1.811 2 x 2 x 5-3/4 50.8 x 50.8 x 146.0 0.408 0.185 100X687 14 68 0.0713 1.811 2 x 2 x 7-3/4 50.8 x 50.8 x 196.8 0.571 0.258 100X689 14 68 0.0713 1.811 2 x 2 x 9-3/4 50.8 x 50.8 x 247.6 0.734 0.332 80X973 12 97 0.1017 2.583 2 x 2 x 3-3/8 50.8 x 50.8 x 85.7 0.349 0.158 100X975 12 97 0.1017 2.583 2 x 2 x 5-3/4 50.8 x 50.8 x 146.0 0.582 0.263 100X977 12 97 0.1017 2.583 2 x 2 x 7-3/4 50.8 x 50.8 x 196.8 0.814 0.369 60X979 12 97 0.1017 2.583 2 x 2 x 9-3/4 50.8 x 50.8 x 247.6 1.047 0.474 60
EasyClip™ Support Clips (X-Series™)
EasyClip
™Support C
lips (X-Series™)
OvernightDelivery!
Available for
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:08 AM Page 103
104 The place to stop…before the building starts! SMrequest a quote online @
Easy
Clip
™En
d C
lips
(A-S
erie
s™)
Dietrich EasyClip™ A-Series™ end clips are mostcommonly used to reinforce connections in kneewall applications or to reinforce jamb studconnections to the primary frame. These clips are unpunched as the specific application willdetermine the appropriate number and placementof fasteners.
Used in knee wall connections or to reinforce jamb studconnections at the primary frame.■ 3” x 3” legs.
■ Available in 16, 14 and 12 gauge.
■ A-Series™ clips are unpunched.
■ Lengths available: 3” and 6”.
■ G 90, 50 ksi steel. EasyClip™ End Clips (A-Series™)
DMF Thickness Size Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm lbs kg Pcs/Code Inches mm BucketA543 16 54 0.0566 1.438 3" x 3" x 3" 76.2 x 76.2 x 76.2 0.290 0.131 50A546 16 54 0.0566 1.438 3" x 3" x 6" 76.2 x 76.2 x 152 0.580 0.262 50A683 14 68 0.0713 1.811 3" x 3" x 3" 76.2 x 76.2 x 76.2 0.360 0.163 50A686 14 68 0.0713 1.811 3" x 3" x 6" 76.2 x 76.2 x 152 0.720 0.326 50A973 12 97 0.1017 2.583 3" x 3" x 3" 76.2 x 76.2 x 76.2 0.510 0.231 50A976 12 97 0.1017 2.583 3" x 3" x 6" 76.2 x 76.2 x 152 1.020 0.462 50
EasyClip™ End Clips (A-Series™)
OvernightDelivery!
Available for
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:08 AM Page 104
105For more information or to contact a sales representative, see page 3
Exterior Light-Gauge Connections/Accessories for Rigid ConnectionsSim
pson®
Holdow
ns (HD
Series) & Simpson
®Tension Ties (H
T14)
Simpson® Tension Ties aredesigned to provide an economicaloption for light to medium upliftrequirements. Simply screw tensionties, with #10 screws, to the studsthrough prepunched holes andsecure to the foundation withanchor bolts.
Simpson* Holdowns provide cost-effective shear wall attachment withallowable loading available for 20- through 16-gauge studs.Installation is made easy withprepunched holes. Fill each holewith a #10 screw for maximum load capacity.
Used to secure and hold down shearwalls to the structure foundation.■ Three sizes for optimal performance.
■ Two-piece welded construction.
■ ICBO ER #5275 recognized.
*Simpson is a registered trademark of the Simpson Strong-Tie Company, Inc.
Single-piece tension tie for shear wall anchorage.■ Single-piece construction.
■ Post pour installation.
■ ICBO ER #5275 recognized.
DMF Thickness Size Weight/PieceProduct Gauge Mils Design Thickness Inches mm lbs kg PackagingCode Inches mmHD8 10 118 0.1242 3.155 2-1/2 x 13-7/8 63.5 x 352 3.30 1.49 PackageHD10 10 118 0.1242 3.155 2-1/2 x 16-1/8 63.5 x 410 3.40 1.54 dependent onHD15 7 170 0.1790 4.547 2-3/4 x 21-1/2 69.9 x 546 7.50 3.39 order quantity
Simpson® Holdowns (HD Series)
DMF Thickness Size Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm lbs kg Pcs/Code Inches mm BoxHT14 11 114 0.120 3.048 2-1/2 x 15 63.5 x 381 2.150 0.975 10
Simpson® Tension Ties (HT14)
OvernightDelivery!
Available for
OvernightDelivery!
Available for
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:08 AM Page 105
106 The place to stop…before the building starts! SMrequest a quote online @
Spaz
zer®
5400
(SP
ZS)
Spaz
zer®
Snap
-In G
rom
met
(SP
GR)
and
Spa
zzer
®Ba
r G
uard
™(S
PBG
)
Dietrich TradeReady® Spazzer® 5400Spacer Bar is a pre-notched, 16-gauge, galvanized steel spacerand bridging bar, engineered tofacilitate the rapid erection ofexterior curtain-wall framing, load-bearing walls and high interiorpartitions constructed of structuralstuds. Until now, most bridging insteel studs was accomplished withcold-rolled channel that requiredbridging clips or welding. The Spazzer® bridging bar is equipped with proprietarypre-punched slots that reduce installation costs andprovide excellent torsional and lateral stud restraint. The Spazzer® Bar Guard™ retainer clip or the Spazzer® Snap-In Grommet should be used to secure the Spazzer® Bar when used in load-bearing applications.
Nonload-BearingWall Installation:The TradeReady® Spazzer® 5400 bar ispassed through the stud knockouts androtated 90° into position, engaging eachside of the knockout. For load-bearingstuds, the Spazzer® 5400 Bar Guard™bar retainer clip, the Spazzer® Snap-InGrommet or screws are required to keepthe bar in place. The TradeReady® Spazzer®
5400 bar should be installed at a maximum4' O.C. vertically or per specifications. TheTradeReady® Spazzer® bar should not beused in studs over 8" wide.*
Load-Bearing WallInstallation:The TradeReady® Spazzer® 5400 bar ispassed through the stud knockouts androtated 90° into position, engaging eachside of the knockout. For 20-gauge studs,the Spazzer® 5400 Bar Guard™ barretainer clip, the Spazzer® Snap-InGrommet or screws are required to keepthe bar in place. The TradeReady®
Spazzer® 5400 bar should be installedat maximum 5' O.C. vertically or perspecification, and should not be used instuds over 8" wide.*
U.S. Patent No. 6, 708, 460 andother PatentsPending
OvernightDelivery!
Available for
Spazzer®
5400Spazzer®
Snap-inGrommet
DMF Thickness Size Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm lbs kg Pcs/ Pcs/Code Inches mm Bundle SkidSPZS 16 54 0.0566 1.438 1-1/4 x 1-1/4 x 50 31.8 x 31.8 x 1270 2.060 0.932 NA 680
*When bridging 8" wall studs the allowable moment capacity calculated in accordance with Section C3.1.2.1 of the North American Specification forthe Design of Cold-Formed Steel Structural Members should be factored by 0.9 for U-Channel, and 0.8 for Spazzer 5400. Contact Dietrich DesignGroup at 1-800-873-2443 for additional clarification if needed.
Spazzer® 5400
DMF Size Weight/Piece PackagingProduct Inches mm lbs kg Pcs/Code BoxSPBG 3-1/4 x 1-5/8 82.6 x 41.3 0.04 0.02 100SPGR 1-1/2 x 4 38.1 x 101.6 0.06 0.03 100
Spazzer® Bar Guard™ and Spazzer® Snap-In Grommet
Bridging installation up to 30% faster with up to 40% less labor.■ Fast, easy and efficient.
■ Reduces labor up to 40%.
■ Eliminates clip angles, bridging clips and welding.
■ Prenotched at 12”, 16” and 24” intervals so no layout is required. Spazzer®
Bar Guard™
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:08 AM Page 106
107For more information or to contact a sales representative, see page 3
Exterior Light-Gauge Framing Accessories for Bridging and Bracing
Dietrich U-Channel, EasyClip™ ClipAngles (U-Series™) and screws areone of the most common bridgingmethods used to provide resistanceto stud rotation and minor axisbending under wind and axial loads. 1-1/2" U-Channel is passed throughthe stud knockout and securedwith EasyClip™ Clip Angles (U-Series™) and screws. Lateralbracing is typically installed at amaximum of 48" O.C. ConsultDietrich’s Technical Design Guide forproper spacing when using the design tables.
Caution: EasyClip™ Clip Angles (U-Series™) must be used with screws to brace cold-formed framing properly. U-Channel does not provide proper bracing if it is notadequately attached to the framing member.
Traditional cold-rolled bridging with clip angleand screw attachment.■ Traditional bracing to prevent stud rotation.
■ EasyClip™ Clip Angles (U-Series™) are punched for easy attachment.
■ Labor-intensive assembly.
U-C
hannel (CH
N) and EasyC
lip™
Clip Angles (U
-Series™)
U-Channel
EasyClip™ Clip Angles(U-Series™)
DMF Thickness Size Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm lbs kg Pcs/Code Inches mm BucketU543 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 3-3/8 38.1 x 38.1 x 85.7 0.160 0.072 400U545 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 5-3/4 38.1 x 38.1 x 146 0.280 0.127 200U547 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 7-3/4 38.1 x 38.1 x 196 0.370 0.167 100U549 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 9-3/4 38.1 x 38.1 x 248 0.470 0.213 100
*Also available in 14 and 12 gauge.
EasyClip™ Clip Angles (U-Series™)
DMF CSSBI Thickness Size Weight PackagingProduct Reference Gauge Mils Design Thickness Inches mm lbs/ft kg/m Pcs/ Pcs/Code Inches mm Bundle SkidCHN1 075U50-54 16 54 0.0566 1.438 3/4 19.1 0.250 0.371 10 360CHN2 150U50-54 16 54 0.0566 1.438 1-1/2 38.1 0.420 0.623 10 330
*Available in 10', 16' and 20' lengths.
U-Channel (CHN Series™)
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:08 AM Page 107
108 The place to stop…before the building starts! SMrequest a quote online @
U-C
hann
el (
CH
N)
and
Wel
ding
Dietrich U-Channel and weldedattachments provide horizontalbridging to resist studrotation and minor axisbending under wind and axial loads. 1-1/2"U-Channel is passedthrough the studknockout andwelded at allattachment points.Lateral bridging is typicallyinstalled at a maximum of 48" O.C.spacing. Consult Dietrich’s TechnicalDesign Guide for proper bridging spacing when using thedesign tables. Welded U-Channel should not be used instuds wider than 6"
Caution: Extreme care should be taken in the quality ofthe weld. If the weld burns through or does not penetrate,the U-channel will not be effective.
Traditional cold-rolled bridging withweld attachment.■ Traditional bracing to prevent stud rotation.
■ Welds are required at all connection points.
■ Specialized equipment and personnel are required.
U-Channel
DMF CSSBI Thickness Size Weight PackagingProduct Reference Gauge Mils Design Thickness Inches mm lbs/ft kg/m Pcs/ Pcs/Code Inches mm Bundle SkidCHN2 150U50-54 16 54 0.0566 1.438 1-1/2 38.1 0.420 0.623 10 330
*Available in 10', 16' and 20' lengths.
U-Channel (CHN Series™) and Welding
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:08 AM Page 108
109For more information or to contact a sales representative, see page 3
Exterior Light-Gauge Framing Accessories for Bridging and Bracing
Properly spacedhorizontal steel bracingprovides resistance tostud rotation and minoraxis buckling under windand axial loads. Block andstrapping is typically usedwhen wall studs exceed6". U-Channel or theSpazzer® bar does notprovide sufficient bracingfor members wider than6". Both stud flanges must
be attached to top and bottom runner flanges to provide properend support. Floor and ceiling runners must also be anchoredsecurely to the structure. To utilize the stud’s load carryingcapacity fully, horizontal bracing must be installed at properintervals.
Lateral bracing consists of a field-cut stud or track for solid blockingand steel strap bracing on both flanges of the studs. Solid blockingis placed at each end of the wall, adjacent to wall openings and 8'O.C. maximum. The blocking is attached to each adjacent stud viaEasyClip™ E- or S- Series™ clips, or when a track is used, the flangesare cut, the web bent and a minimum 4" overlap is used to securethe track block to the studs. Strap bracing, 2" wide and 20-gauge(33 mil) minimum, is fastened to each solid block and stud flange.
Commonly used bracing for wallstuds deeper than 6".■ Provides horizontal bracing for studs deeper than 6”.
■ Blocking is field cut.
■ Used if knockouts do not align.
Block (TSB) and Strap (DT Series
™)
DT Strapping
DMF Thickness Size Available Length PackagingProduct Gauge Mils Design Thickness Min. Width Max. Width Pcs/Code Inches mm Inches mm Inches mm ft m Skid
DTN3 20 33 0.0346 0.879 2 50.8 12 305 10 3.05 20018 43 0.0451 1.146 2 50.8 12 305 10 3.05 20016 54 0.0566 1.438 2 50.8 12 305 10 3.05 200
DTN5 14 68 0.0713 1.811 2 50.8 12 305 10 3.05 20012 97 0.1017 2.583 2 50.8 12 305 10 3.05 200
DTN3 has a yield strength of 33,000 psi.DTN5 has a yield strength of 50,000 psi.
Strapping (DT-Series™)
Solid Blocking (CS/TS)Blocking is typically field cut from the same or heavier excess track stock and secured between wall studs. Stud stock is also an option. Studs are attached using EasyClip™
Clip Angles (S-Series™). Blocking should be installed in the first and last two bays and every 8 feet in between.
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:08 AM Page 109
110 request a quote online @
Dia
gona
l Ten
sion
Stra
ppin
g/Sh
ear
Wal
l Bra
cing
(D
T)/G
usse
t Pla
tes
(GP)
for
Shea
r W
all B
raci
ng
Dietrich diagonaltension strappingand gusset platecomponents are usedin combination toprovide shearwall(racking restraint) for light-gauge load- bearing framingunder wind andseismic loads. They
are normally installed on both sides of the wall directly over
framing members and are easily covered with facing materials.
Straps are positioned diagonally from the bottom track to the top track. In order to resist load in each direction, an X-configuration should be used. At a minimum, double studsare positioned at ends of the X-brace to serve as compressionstuds. Straps are either attached directly to the compressionstuds or are attached via gusset plates. Compression studsmust be anchored to the foundation, normally with Simpson*uplift anchors. For multi-story construction, the uplift loads areextremely high. It is not uncommon to require 20,000 to40,000 pounds of uplift force at these connections. SinceSimpson® anchors are not designed to resistthis magnitude of force, it isrecommended
that embedded plates be installed prior to pouring theconcrete foundation. A heavy steel assembly is then welded tothe embedded plate and to the compression studs.
Caution: Racking loads are first transferred to the roof orfloor decking and then to the shearwalls (X-bracing). The X-bracing then relies on a proper foundation to resist uplift andshear forces. In order for the system to function properly, theload path from the roof or floor deck to the shearwalls to thefoundation must be complete. This normally requiresadditional bracing, blocking, track and rim splices, drag struts,uplift anchors and heavy-duty foundations.
DT Strapping
Gusset Plates
Light-gauge steel X-bracing for load-bearing framing to resist rackingunder wind and seismic loads.■ Strapping is available in flat lengths and coil form.
■ Available widths are 2”, 4”, 6”, 8”, 10” and 12”.
■ Gauges: 20 (33 mils), 18 (43 mils), 16 (54 mils), 14 (68 mils) and 12 (97 mils).
■ Standard gusset plate sizes are 6”x6”, 6”x12” and 12”x12”.
*Simpson is a registered trademark of Simpson Strong-Tie Company, Inc.
The place to stop…before the building starts! SM
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:08 AM Page 110
111For more information or to contact a sales representative, see page 3
Exterior Light-Gauge Framing Accessories for Bridging and BracingD
iagonal Tension Strapping/Shear Wall Bracing (D
T)/Gusset Plates (G
P) for Shear Wall Bracing
DMF Thickness Plate Size Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm lbs kg Pcs/Code Inches mm Skid
6 x 6 152 x 152 0.580 0.263 2516 54 0.0566 1.438 6 x 12 152 x 305 1.170 0.532 25
GP12 x 12 305 x 305 2.330 1.059 256 x 6 152 x 152 1.050 0.477 25
12 97 0.1017 2.583 6 x 12 152 x 305 2.090 0.950 2512 x 12 305 x 305 4.190 1.900 25
Gusset Plates (GP) for Shear Wall Bracing
DMF Thickness Size Available PackagingProduct Gauge Mils Design Thickness Min. Width Max. Width Pcs/Code Inches mm Inches mm Inches mm Skid
20 33 0.0346 0.879 2 50.8 12.0 305 1 coil18 43 0.0451 1.146 2 50.8 12.0 305 1 coil
DTNC* 16 54 0.0566 1.438 2 50.8 12.0 305 1 coil14 68 0.0713 1.811 2 50.8 12.0 305 1 coil12 97 0.1017 2.583 2 50.8 12.0 305 1 coil
*20- and 18-gauge are 33,000 psi yield strength. 16-, 14- and 12-gauge are 50,000 psi yield strength.
Diagonal Tension Strapping/Shear Wall Bracing (DT)
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:08 AM Page 111
112 The place to stop…before the building starts! SMrequest a quote online @
Cor
ner
Angl
e (C
AM)
Dietrich heavy-gauge corner angle is commonly used for avariety of applications including: concrete pour stop,connection strut or angle, roof ridge angles and cornerreinforcement.
Corner Angle
Heavy-gauge utility or corner angle.■ Standard leg sizes are 2”x2”, and 3”x3”.
■ Wider and uneven leg sizes available.
■ Available in 18, 16, 14 and 12 gauge.
■ Standard 10’ lengths. Other lengths available on request.
DMF Thickness Size* Length* Weight PackagingProduct Gauge Mils Design Thickness Inches mm ft m lbs/ft kg/m Pcs/Code Inches mm SkidCAE 20 33 0.0346 0.879 2 x 2 50.8 x 50.8 10 3.05 0.470 0.699 500
18 43 0.0451 1.146 2 x 2 50.8 x 50.8 10 3.05 0.620 0.922 250
CAM16 54 0.0566 1.438 2 x 2 50.8 x 50.8 10 3.05 0.770 1.141 25014 68 0.0713 1.811 2 x 2 50.8 x 50.8 10 3.05 0.980 1.453 25012 97 0.1017 2.583 2 x 2 50.8 x 50.8 10 3.05 1.400 2.076 250
CAE 20 33 0.0346 0.879 3 x 3 76.2 x 76.2 10 3.05 0.680 1.010 50018 43 0.0451 1.146 3 x 3 76.2 x 76.2 10 3.05 1.020 1.515 250
CAM16 54 0.0566 1.438 3 x 3 76.2 x 76.2 10 3.05 1.290 1.915 25014 68 0.0713 1.811 3 x 3 76.2 x 76.2 10 3.05 1.530 2.270 25012 97 0.1017 2.583 3 x 3 76.2 x 76.2 10 3.05 2.140 3.175 250
*Other sizes available on request.
Corner Angle (CAM)
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:08 AM Page 112
113For more information or to contact a sales representative, see page 3
Exterior Light-Gauge Framing Accessories for Various Framing Applications
Dietrich heavy-duty furring channel is a high-performance hat-shapedframing component usedin ceiling, exterior wall and roofapplications. In ceiling applications, heavy-duty furringis tie-wired or mechanically fastened to bar joists, other roof or floor framing.Gypsum wallboard is secured to the furring. In roof applications, heavy-duty furringis used as purlins to provide connection points for roof sheathing.
Heavy-duty furring provides greater resistanceto deflection and bending. Greater spans andheavier loads are achieved as a result.■ Standard sizes are 7/8” and 1-1/2” deep.
■ Available in 16 and 18 gauge.
Heavy-D
uty Furring Channel (FC
M)
Heavy-Duty FurringChannel
DMF SSMA Thickness Size Weight PackagingProduct Reference Gauge Mils Design Thickness Inches mm lbs/ft kg/m Pcs/Code Inches mm SkidFCM 087F125-43 18 43 0.0451 1.146
7/8 22.20.555 0.823 250
FCM 087F125-54 16 54 0.0566 1.438 0.670 0.994 250FCMD 150F125-43 18 43 0.0451 1.146
1-1/2 38.10.733 1.089 250
FCMD 150F125-54 16 54 0.0566 1.438 0.920 1.364 250
Heavy-Duty Furring Channel (FCM)
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:08 AM Page 113
Cus
tom
Sha
pes
and
Mis
cella
neou
s An
gles
(VS
)
■ Precision fabrication meetingexacting specifications.
■ Wide array of custom options.
■ Fully dimensioned partdrawings must be provided.
Custom fabricated shapes, clips, bends,continuous angles, long leg tracks and miscellaneous closures.
Dietrich custom fabricates just about any shape, bend,angle or specialty framing component to your exactspecification. Custom parts include cornerangles, roof ridge angles, clip angles, longand uneven leg tracks, eaveclosures, support clips andfurring channels. To ensureproper fabrication, Dietrichrequires a detailed, fullydimensioned part drawing attime of order placement.
114 The place to stop…before the building starts! SMrequest a quote online @
08216 Exterior Framing 59-114:DMF07_072-073 7/2/10 11:08 AM Page 114
115
Floor Joist Systems/ComponentsLight-Gauge C-Joist Framing (CS/TS-Series™) ........................118–119TradeReady® Steel Joists (TDJ and TDW Series™)..........120–121TradeReady® Grommet (TDGR) ....121TradeReady® Rim (TD-Series™) ......122TradeReady® Structural Blocking (TDSB) ..................................123Floor Joist Framing AccessoriesBlock (TS/CS), Strap (DTN) and EasyClip™
(E- and S- Series™) ..................124–125EasyClip™ QuickTwist™
Web Stiffener (QTWS) ......................126Web Stiffener (WS) ............................127Simpson® Tension Bracing (TB27) ....................................128TradeReady® Structural Blocking (TDSB) ..................................128Floor Joist Hangers and ConnectorsSimpson® (SJCT) 8-14 Hanger......129Simpson® Bridle Hanger (SLBV/SMB)..........................................130Simpson® Ledger Connector System (ICFL) ......................................131Simpson® Skewable Angle Hangers (SLS5/SLS7) ......................132Lateral Tie Plate (LPT4) ....................133Foundation Clips (FDCL)..................134
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 1
116
Floo
r Fr
amin
g O
verv
iew
Floor Joist Systems/Components
Floor joist components are available in a varietyof web sizes, flanges, gauges and yield strengths.This wide selection of webs, flanges, gauges andyield strengths (ksi) enable the designer toobtain optimal performance at economicalprices.
Dietrich’s conventional C-Joist system is madeup of joists, track, clips, web stiffeners, solidblocking and strapping to complete an entireassembly.
The revolutionary TradeReady® Floor System iscomprised of the TradeReady® Joist with largeextruded holes, TradeReady® Rim Joist with pre-punched layout tabs and embedded stiffeningribs, and pre-cut structural blocking. The systemis complemented with EasyClip™ S- and E-series™
clips and web stiffeners when necessary.
Floor Joist Framing Accessories
Dietrich Metal Framing offers a wide selection of floor framing accessories to ensuremaximum floor performance. Choose from our wide assortment of web stiffeners,blocking, bracing and strapping.
Floor Joist Hangers and Connectors
Dietrich’s wide assortment of hangers and connectors gives you the flexibility tochoose from a variety of products that provide connection solutions to complexframing details. Choose from our universal joist, bridle, skewable and ICF hangers.
The place to stop…before the building starts!SMrequest a quote online @
FLOORFRAMINGOVERVIEW
Light-gauge C-Studs/Joists are com-monly used in floor framing assem-blies. C-Joists are a cost-effective alter-native to open web trusses, bar joists,engineered lumber, and cast-in-placeor hollow-core floor assemblies. Lightsteel framing (C-Joists) are ideal forlow- and mid-rise commercial appli-cations such as hotels, motels, apart-ment complexes, condominiums,multi-family, and assisted living. Steeljoists are also being used more exten-sively in residential structures.
Steel’s high strength-to-weight ratioprovides strong loading capacity andmaximum spanning capability. Joistsare commonly spaced at 12", 16",19.2" or 24" intervals and are used inconjunction with all traditionalflooring materials such as plywood,OSB, concrete filled steel deck, or oneof the many varieties of fiber rein-forced cement board.
Dietrich offers a variety of floor fram-ing systems including conventionalC-Joist and the TradeReady® SteelJoist System. The TradeReady® SteelJoist System features large extrudedopenings in the joist to accommodateelectrical, mechanical, plumbingand technology lines. The system alsoincludes a tabbed rim track tostrengthen the joist against web crip-pling loads, and to provide greaterversatility and strength for ledgerapplications. This system, in con-junction with other floor sheathingproducts, provides one of the mostcost-effective systems for non-com-bustible low and mid-rise structures.
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 116
117For more information or to contact a sales representative, see page 3.
Overview
U.S. Patent Nos. 6,301,854; 6,418,694; 6,691,478 and other U.S. and foreign patents pending.
Use instead of wood joists.■ Long-term price stability.
■ Steel is recycled — saves trees.
■ Eliminates floor squeakcomplaints.
Prespaced joist tabs.■ No layout required.
■ Eliminates joist hangers.
Greater spanningcapabilities.■ Design flexibility.
■ Wider O.C. spacing requires fewer joists.
■ Wide flange for plywoodattachement.
■ Structural blocking prevents racking.
Prepunched openings.■ No drilling or cutting
joist webs.
■ Increases ceiling height.
■ Eliminates soffit framing.
The DietrichTradeReady®
Floor System
Floor Framing O
verview
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 117
118 The place to stop…before the building starts! SMrequest a quote online @
Ligh
t-G
auge
C-J
oist
Fra
min
g (C
S/TS
Ser
ies™
)
Dietrich C-Joist components provide an economical, lightweight alternative to open web trusses, barjoists, engineered lumber, cast-in-place or hollow core floor assemblies. Depending on loads and spans,C-Joists are typically spaced at 12", 16", 19.2" or 24" on-center spacing. Structural track (TSB), usuallyin the same gauge as the joist, is used as rim or band enclosures. Joist to girder attachments arenormally supported with joist hangers, EasyClip™ E-Series™ or S-Series™ support clips. Web stiffenersmay be required at supports and other point loads. Solid blocking and strap bridging is required toproperly brace the floor assembly.
DMF SSMA Thickness Depth Flange ReturnProduct Reference Gauge Inches mm Inches mm Inches mmCode* (mils)
800S162-x 18 (43) 8 203 1-5/8 41.3 1/2 12.7
CSJ1000S162-x 16 (54) 10 254 1-5/8 41.3 1/2 12.71200S162-x 14 (68) 12 305 1-5/8 41.3 1/2 12.71400S162-x 12 (97) 14 356 1-5/8 41.3 1/2 12.7800S200-x 18 (43) 8 203 2 50.8 5/8 15.9
CSW1000S200-x 16 (54) 10 254 2 50.8 5/8 15.91200S200-x 14 (68) 12 305 2 50.8 5/8 15.91400S200-x 12 (97) 14 356 2 50.8 5/8 15.9800S250-x 18 (43) 8 203 2-1/2 63.5 5/8 15.9
CSE1000S250-x 16 (54) 10 254 2-1/2 63.5 5/8 15.91200S250-x 14 (68) 12 305 2-1/2 63.5 5/8 15.91400S250-x 12 (97) 14 356 2-1/2 63.5 5/8 15.9800S300-x 18 (43) 8 203 3 76.2 1 25.4
CSS1000S300-x 16 (54) 10 254 3 76.2 1 25.41200S300-x 14 (68) 12 305 3 76.2 1 25.41400S300-x 12 (97) 14 356 3 76.2 1 25.4
*18-gauge is standard as 33 ksi yield strength. 16, 14, 12-gauge are standard as 50 ksi yield strength.x= SSMA reference of mils at the end of the character string.
Light-Gauge C-Joist Framing (CS/TS Series™)
C-Joist
Conventional C-Joist componentsprovide a lightweight, low-cost,rigid floor assembly.■ Precut to exacting sizes and readily available.
■ Joist sizes include 8”, 10”, 12” and 14”.
■ Available in 18, 16, 14 and 12 gauge.
■ Flange widths include 1-5/8”, 2”, 2-1/2” and 3”.
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 118
119For more information or to contact a sales representative, see page 3.
Floor Joist Systems/ComponentsLight-G
auge C-Joist Fram
ing (CS/TS Series
™)
DMF SSMA Thickness Depth FlangeProduct Reference Gauge Inches mm Inches mmCode* (mils)
800T125-x 18 (43) 8 203 1-1/4 31.8
TSB1000T125-x 16 (54) 10 254 1-1/4 31.81200T125-x 14 (68) 12 305 1-1/4 31.81400T125-x 12 (97) 14 356 1-1/4 31.8
18-gauge is standard as 33 ksi yield strength. 16, 14 and 12-gauge are standard as 50 ksi yield strength.*The depth of TSB is measured to the inside of the flanges.x= SSMA reference of mils at the end of the character string.
Structural Track (TS-Series™)
Structural Track (Rim)
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 119
120 The place to stop…before the building starts! SMrequest a quote online @
Trad
eRea
dy®
Stee
l Joi
sts
(TD
J an
d TD
W S
erie
s™)
Dietrich TradeReady® steel joists are one of the primarycomponents that make up the TradeReady® floor system. Thesejoists feature large extruded holes that accommodate HVAC,mechanical, plumbing and sprinkler runs. The joist also featuresa series of smaller holes for electrical and technology lines.
Dietrich TradeReady® steel joists are precision manufacturedfrom corrosion-resistant galvanized steel. Steel joists offerconsistent quality, predictable performance and high strengthto weight ratio, and they are dimensionally stable. They won’texpand, contract or shrink; they won’t warp, crack or twist.Steel joists integrate easily with other building materials suchas structural steel, concrete, ICF and wood construction.
Joists can be ordered in standard lengths or to your exactspecifications to minimize waste. Consult the Dietrich TechnicalDesign Guide or the TradeReady® Steel Joist Design Guide forphysical and structural properties, span charts and loading data.
DMF Thickness Depth Flange ReturnProduct Gauge Inches mm Inches mm Inches mmCode* (mils)
7-1/4 184 1 3/4 44.5 5/8 15.9TDJ3 (18 gauge) 18(43) 8 203 1 3/4 44.5 5/8 15.9
TDJ5 (16, 14 & 12 gauge) 16(54), 14(68), 12(97) 9-1/4 235 1 3/4 44.5 5/8 15.911-1/4 286 1 3/4 44.5 5/8 15.9
10 254 2 50.8 5/8 15.9TDW3 (18 gauge) 18(43)
12 305 2 50.8 5/8 15.9TDW5 (16, 14 & 12 gauge) 16(54), 14(68), 12(97)
14 356 2 50.8 5/8 15.9
*18-gauge is standard as 33 ksi yield strength. 16,14 and 12 gauge are standard as 50 ksi yield strength.**UL and UL Classified are trademarks of Underwriter’s Laboratories, Inc.
TradeReady® Steel Joist (TD Series™)
Next-generation, high-performance TradeReady®
Steel Joists are the premier floor joist system for both commercial and residential framing.■ Clear spans up to 33’.
■ Large extruded openings to accommodate electrical, HVAC, plumbing and technology lines.
■ Hole sizes range from 4-1/4” oval to 10” round based on member depth.
■ Superior strength permits wider O.C. spacing.
■ Pre-cut to your exact specifications—no waste.
■ Available in 7-1/4”, 8”, 9-1/4”, 10”, 11-1/4”, 12” and 14” deep members.
■ Flange sizes include 1-3/4” and 2”.
■ Eliminates soffit framing.
■ UL** Listed assemblies L564, G535, G536, G551, G553 and G560.
TradeReady® Joists
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 120
121For more information or to contact a sales representative, see page 3
Floor Joist Systems/ComponentsTradeReady
®Steel Joists (TD
J and TDW
Series™) and TradeReady
®G
romm
ets (TDG
R)
Hole Hole Hole Web Web Size Size Shape Width Width
Inches mm Inches mm
4-1/4" x 7" 108 x 1787-1/4" TDJ 184 TDJ
8" TDJ 203 TDJ
6-1/4" x 9" 159 x 2299-1/4" TDJ 235 TDJ10" TDW 254 TDW
11-1/4" TDJ 286 TDJ
8" Diam. 203 12" TDW 305 TDW
10" Diam. 254 14" TDW 356 TDW
TradeReady™ Joist (TD-Series™)
TradeReady® Grommet protectsand isolates electrical wiring.■ Snaps quickly into TradeReady® 12” TDW joist (all gauges)
■ Provides 360˚ cable protection
■ Simplifies cable pull through
■ Delivers compliance with NEC Article 300.4(B)(1) and CEC Rule 12-516
■ Aids in the separation of cables to prevent bundling
■ Ideal for ROMEX®/ NM type cables: 6/2, 6/3, 8/2, 8/3, 10/2, 10/3, 12/2, 12/3, 14/2, 14/3, etc…
TradeReady® Grommets are used in construction anytime itis required by building code to protect electrical wiring.The grommet is specially designed for the 12" TradeReady®
Floor Joist System.
DMF Pcs/ Weight/BoxProduct Box lbs kgCodeTDGR 36 12 5.44
UL Pending
TradeReady® Grommets (TDGR)
TradeReady® Grommet
NEWITEM
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 121
Trad
eRea
dy®
Rim
Next-generation TradeReady® Rim has preformed tabs atstandard spacings for rapid and easy installation of TradeReady® Steel Joists.■ Rims have preformed tabs at 12”, 16”, 19.2” or 24” intervals
that eliminate layout.■ Eliminates or drastically reduces support clips, joist hangers and web stiffeners.■ Standard 16‘ lengths.■ Sizes include 7-1/4”, 8”, 9-1/4”, 10”, 11-1/4”, 12” and 14”.
Dietrich TradeReady® rim is another major component of the TradeReady® steel floorsystem. The rim is an integral part of the system and drastically reduces framing time and effort.Rims have preformed attachment tabs at 12", 16", 19.2" or 24" O.C. spacing to eliminatelayout time. The tabs are also prepunched to ensure fast, accurate and proper fastenerplacement. Embossed stiffening ribs on each side of the preformed tabs provide additionalreinforcement, resulting in a significant reduction of web stiffeners (squash blocks) andsupport clips in a majority of applications. Once rims are installed, simply tilt up the floor joist, abut tothe tab and screw attach.
U.S. Patent Nos. 6,301,854; 6,691,478; 6,418,694 and other patents pending.
DMF Thickness Depth Flange Length Tab SpacingProduct Gauge Inches mm Top Bottom Inches mmCode (Mils) Inches mm Inches mm
7-1/4 184 1-1/4 31.8 2-1/2 63.5 12 305
18(43)8 203 1-1/4 31.8 2-1/2 63.5 12 305
16(54)9-1/4 235 1-1/4 31.8 2-1/2 63.5 12 305
TD1214(68)
10 254 1-1/4 31.8 2-1/2 63.5 12 305
12(97)11-1/4 286 1-1/4 31.8 2-1/2 63.5 12 305
12 305 1-1/4 31.8 2-1/2 63.5 12 30514 356 1-1/4 31.8 2-1/2 63.5 12 305
7-1/4 184 1-1/4 31.8 2-1/2 63.5 16 406
18(43)8 203 1-1/4 31.8 2-1/2 63.5 16 406
16(54)9-1/4 235 1-1/4 31.8 2-1/2 63.5 16 406
TD1614(68)
10 254 1-1/4 31.8 2-1/2 63.5 16 406
12(97)11-1/4 286 1-1/4 31.8 2-1/2 63.5 16 406
12 305 1-1/4 31.8 2-1/2 63.5 16 40614 356 1-1/4 31.8 2-1/2 63.5 16 406
7-1/4 184 1-1/4 31.8 2-1/2 63.5 19.2 488
18(43)8 203 1-1/4 31.8 2-1/2 63.5 19.2 488
16(54)9-1/4 235 1-1/4 31.8 2-1/2 63.5 19.2 488
TD1914(68)
10 254 1-1/4 31.8 2-1/2 63.5 19.2 488
12(97)11-1/4 286 1-1/4 31.8 2-1/2 63.5 19.2 488
12 305 1-1/4 31.8 2-1/2 63.5 19.2 48814 356 1-1/4 31.8 2-1/2 63.5 19.2 488
7-1/4 184 1-1/4 31.8 2-1/2 63.5 24 610
18(43)8 203 1-1/4 31.8 2-1/2 63.5 24 610
16(54)9-1/4 235 1-1/4 31.8 2-1/2 63.5 24 610
TD2414(68)
10 254 1-1/4 31.8 2-1/2 63.5 24 610
12(97)11-1/4 286 1-1/4 31.8 2-1/2 63.5 24 610
12 305 1-1/4 31.8 2-1/2 63.5 24 61014 356 1-1/4 31.8 2-1/2 63.5 24 610
TradeReady® Rim is only available in 16' stock lengths.
TradeReady® Rim (TD-Series™)
122 The place to stop…before the building starts! SMrequest a quote online @
TradeReady® Rim
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 122
Floor Joist Systems/Components
DMF Thickness Depth Effective LengthProduct Gauge (Mils) Inches mm Inches mmCodeTDSB 18(43) 2-1/2 63.5 12 305TDSB 18(43) 2-1/2 63.5 16 406TDSB 18(43) 2-1/2 63.5 19.2 488TDSB 18(43) 2-1/2 63.5 24 610
TradeReady® Structural Blocking (TDSB)
Precut structural blocking that installs easily to the underside of the joists to prevent joist rotation.■ Pre-cut to fit 12”, 16”, 19.2” or 24” spacing.
■ Pre-punched holes for quick attachment.
■ Available in 18 gauge only.
TradeReady®
Structural Blocking (TDSB)
123For more information or to contact a sales representative, see page 3
StructuralBlocking
Dietrich TradeReady®‚ structural blocking is the thirdcomponent of the TradeReady® steel floor system. Structuralblocking is pre-cut to fit securely between the underside ofthe floor joists to prevent joist rotation. Structural blocking is an economical alternative to cross bracing, X-bracing orstrapping. A continuous row of blocking should be installedevery 8' O.C. maximum and staggered for easy attachment.
Caution: In order to prevent joist rolling, the TDSBblocking must be tied into the structure or otherwise bracedagainst lateral movement.
Note: TDSB blocking is not required if sheathing is appliedto the joists top and bottom.
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 123
Bloc
k (T
S/C
S), S
trap
(DTN
) an
d Ea
syC
lip™
(E-
and
S-Se
ries™
)
124 The place to stop…before the building starts! SMrequest a quote online @
Dietrich block andstrap bridging isinstalled to preventjoist rotation andlateral movement.Solid blocking, afield-cut track orjoist section, iswelded or screw-attached betweenthe first and lasttwo outer joist baysand at a maximumof 8' O.C. along
the strap, over all interior supports and adjacent to flooropenings. Two-inch wide corrosion resistant strapping is also screw-attached or welded to the bottom of every joist flange. Lateral support on the top flanges is usuallyprovided by sub floor or deck material.
Spacing of bridging must be calculated based on therequired strength. In general, bridging is installed at amaximum of 8' O.C. spacing perpendicular to the joists. For example, an 18' joist span would require two bridgingruns at 6' O.C. spacing.
Where the sub-floor or decking does not provide lateral support,strap must also be installed on the top flange of the joist.
Block and strap bridging is used to preventjoist rotation and lateral movement.■ Install immediately after joists are erected
and before construction loads are applied.
■ Solid blocking is field cut from track or joist sections.
■ EasyClip™ E-Series™ clips are used to attach blocks to open side of C-Joist.
■ EasyClip™ S-Series™ clips are used to attach blocking to solid side of C-Joist.
EasyClip™
S-Series™EasyClip™
E-Series™
Coil Strapping
DMF Thickness Size Available Length PackagingProduct Gauge Mils Design Thickness Min. Width Max. Width Pcs/Code Inches mm Inches mm Inches mm ft m Skid
DTN3 20 33 0.0346 0.879 2 50.8 12 305 10 3.05 20018 43 0.0451 1.146 2 50.8 12 305 10 3.05 20016 54 0.0566 1.438 2 50.8 12 305 10 3.05 200
DTN5 14 68 0.0713 1.811 2 50.8 12 305 10 3.05 20012 97 0.1017 2.583 2 50.8 12 305 10 3.05 200
DTN3 has a yield strength of 33,000 psi.DTN5 has a yield strength of 50,000 psi.Packaging may vary by region.
Diagonal Tension Strapping (DTN-Series™/Strap)
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 124
Floor Joist Framing AccessoriesBlock (TS/C
S), Strap (DTN
) and EasyClip
™(E- and S-Series
™)
125For more information or to contact a sales representative, see page 3
DMF Thickness Size Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm lbs kg Pcs/ Code Inches mm BucketE543 16 54 0.0566 1.438 4 x 1-1/2 x 3 102 x 38.1 x 76.2 0.270 0.122 100E545 16 54 0.0566 1.438 4 x 1-1/2 x 5 102 x 38.1 x 127 0.440 0.199 100E547 16 54 0.0566 1.438 4 x 1-1/2 x 7 102 x 38.1 x 178 0.620 0.281 100E549 16 54 0.0566 1.438 4 x 1-1/2 x 9 102 x 38.1 x 229 0.800 0.362 50E541 16 54 0.0566 1.438 4 x 1-1/2 x 11 102 x 38.1 x 279 0.970 0.439 50E683 14 68 0.0713 1.811 4 x 1-1/2 x 3 102 x 38.1 x 76.2 0.330 0.149 100E685 14 68 0.0713 1.811 4 x 1-1/2 x 5 102 x 38.1 x 127 0.550 0.249 100E687 14 68 0.0713 1.811 4 x 1-1/2 x 7 102 x 38.1 x 178 0.770 0.384 80E689 14 68 0.0713 1.811 4 x 1-1/2 x 9 102 x 38.1 x 229 0.990 0.448 50E681 14 68 0.0713 1.811 4 x 1-1/2 x 11 102 x 38.1 x 279 1.220 0.552 50E973 12 97 0.1017 2.583 4 x 1-1/2 x 3 102 x 38.1 x 76.2 0.470 0.213 50E975 12 97 0.1017 2.583 4 x 1-1/2 x 5 102 x 38.1 x 127 0.780 0.353 50E977 12 97 0.1017 2.583 4 x 1-1/2 x 7 102 x 38.1 x 178 1.090 0.493 50E979 12 97 0.1017 2.583 4 x 1-1/2 x 9 102 x 38.1 x 229 1.410 0.638 50E971 12 97 0.1017 2.583 4 x 1-1/2 x 11 102 x 38.1 x 279 1.720 0.778 40
EasyClip™ Support Clips (E-Series™)
DMF Thickness Size Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm lbs kg Pcs/ Code Inches mm BucketS543 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 3 38.1 x 38.1 x 76.2 0.140 0.064 400S545 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 5 38.1 x 38.1 x 127 0.240 0.109 200S547 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 7 38.1 x 38.1 x 178 0.340 0.154 100S549 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 9 38.1 x 38.1 x 229 0.430 0.195 100S541 16 54 0.0566 1.438 1-1/2 x 1-1/2 x 11 38.1 x 38.1 x 279 0.530 0.240 100S683 14 68 0.0713 1.811 1-1/2 x 1-1/2 x 3 38.1 x 38.1 x 76.2 0.180 0.082 200S685 14 68 0.0713 1.811 1-1/2 x 1-1/2 x 5 38.1 x 38.1 x 127 0.300 0.136 200S687 14 68 0.0713 1.811 1-1/2 x 1-1/2 x 7 38.1 x 38.1 x 178 0.420 0.191 100S689 14 68 0.0713 1.811 1-1/2 x 1-1/2 x 9 38.1 x 38.1 x 229 0.540 0.245 100S681 14 68 0.0713 1.811 1-1/2 x 1-1/2 x 11 38.1 x 38.1 x 279 0.660 0.299 100S973 12 97 0.1017 2.583 1-1/2 x 1-1/2 x 3 38.1 x 38.1 x 76.2 0.260 0.118 200S975 12 97 0.1017 2.583 1-1/2 x 1-1/2 x 5 38.1 x 38.1 x 127 0.430 0.195 150S977 12 97 0.1017 2.583 1-1/2 x 1-1/2 x 7 38.1 x 38.1 x 178 0.600 0.272 100S979 12 97 0.1017 2.583 1-1/2 x 1-1/2 x 9 38.1 x 38.1 x 229 0.770 0.349 80S971 12 97 0.1017 2.583 1-1/2 x 1-1/2 x 11 38.1 x 38.1 x 279 0.940 0.426 70
EasyClip™ Support Clips (S-Series™)
DMF Thickness Size PackagingProduct Gauge Mils Design Thickness Min. Width Max. Width Pcs/ Code Inches mm Inches mm Inches mm Skid
20 33 0.0346 0.879 2 50.8 12.0 304.8 1 coil18 43 0.0451 1.146 2 50.8 12.0 304.8 1 coil
DTNC 16 54 0.0566 1.438 2 50.8 12.0 304.8 1 coil14 68 0.0713 1.811 2 50.8 12.0 304.8 1 coil12 97 0.1017 2.583 2 50.8 12.0 304.8 1 coil
20 and 18 gauge are 33,000 psi yield strength.16, 14 and 12 gauge are 50,000 psi yield strength.
Diagonal Tension Strapping (DTN-Series™/Coil)
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 125
Easy
Clip
™Q
uick
Twis
t™W
eb S
tiffe
ner
(QTW
S)
126 The place to stop…before the building starts! SMrequest a quote online @
EasyClip™ Quick Twist Web Stiffeners provide excellent reinforcement at criticalload points to prevent web crippling.■ Simple, post installation assembly.
■ Easily rotated in-place for a tight fit.
■ Pre-punched for easy installation of fasteners.
■ Solid 12 gauge construction.
■ One-piece assembly.
QTWS
NEWITEM
DMF Thickness Size* Weight/pcProduct Size
Gauge Mils Design Thickness Inches mm lbs kg PackagingCode (inches) Inches mm
7.25 184.2 1.190 0.5398.00 203.2 1.320 0.599 Packaged9.25 235.0 1.530 0.694 Dependent
QTWS 3-1/2 12 97 0.1017 2.583 10.00 254.0 1.660 0.753 On11.25 285.8 1.880 0.853 Order12.00 304.8 2.000 0.907 Quantity14.00 355.6 2.340 1.0617.25 184.2 1.690 0.7678.00 203.2 1.870 0.848 Packaged9.25 235.0 2.170 0.984 Dependent
QTWS 6 12 97 0.1017 2.583 10.00 254.0 2.350 1.066 On11.25 285.8 2.660 1.207 Order12.00 304.8 2.840 1.288 Quantity14.00 355.6 3.320 1.506
*Dimension is nominal size. Actual product is shorter to fit inside joist.
EasyClip™ Quick Twist Web Stiffener (QTWS)
EasyClip™ Quick Twist Web Stiffeners (QTWS) are used to providereinforcement of joist webs to prevent crippling. Web reinforcement is oftenrequired by design to enhance the load capacity of joists. The unique design ofQTWS allows the installer to insert the stiffener on the inside of the joist afterthe joist is installed. This stiffener eliminates the need to pre-insert traditionalweb stiffeners prior to joist installation.
OvernightDelivery!
Available for
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 126
Floor Joist Framing Accessories
Provides excellent reinforcement at criticalload points to prevent web crippling.■ Prevents web crippling.
■ Significantly enhances joist carrying capacity.
■ Available in 14 gauge only.
Web Stiffener (W
S)
127For more information or to contact a sales representative, see page 3
WS
DMF Thickness Size LengthProduct Gauge Mils Design Thickness Inches mm Inches mmCode Inches mmWS 14 68 0.0713 1.811 4 102 5-3/4 to 13-3/4 146 to 349
Web Stiffener (WS)
OvernightDelivery!
Available for
Dietrich web stiffeners are used to provide reinforcement ofjoist webs to prevent crippling. Web reinforcement is oftenrequired by design to enhance the load capacity of joists.
When installing between the joist flanges, WS web stiffenersmust be installed by sliding it in from the end of the joist. Webstiffeners must be ordered to fit specific joist web dimensions.
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 127
Sim
pson
®Te
nsio
n Br
acin
g (T
B27)
& T
rade
Read
y®St
ruct
ural
Blo
ckin
g (T
DSB
)
128 The place to stop…before the building starts! SMrequest a quote online @
Used in lieu of block and strap to prevent flange rotation and support flanges in compression.■ Eliminates multiple components.
■ Fits 1-5/8”–3” flanges.
■ Available for 12”, 16”, 19.2” or 24” O.C. spacing.
Dietrich TradeReady® structural blocking is pre-cut to fit securely between the underside of floor joists to prevent joistrotation. The structural blocking is an economical alternative to cross bracing, x-bracing or strapping. A continuous row ofblocking should be installed every 8' O.C. maximum and staggered for easy attachment.
CAUTION: In order to prevent joist rolling, the TDSB blocking must be tied into the structure or otherwise braced against lateral movement.
DMF Thickness Depth Effective LengthProduct Gauge (mils) Inches mm Inches mmCodeTDSB 18 (43) 2 1/2 63.5 12 305TDSB 18 (43) 2 1/2 63.5 16 406TDSB 18 (43) 2 1/2 63.5 19.2 488TDSB 18 (43) 2 1/2 63.5 24 610
TradeReady® Structural Blocking (TDSB)
Tension Bracing
Simpson* tension bracing is used to prevent joist compression,flange lateral movement, and rotation. These tension ties areused as an alternative to traditional block and strapping. Tensionties are traditionally used with wood framing, but can also beused with conventional C-joists.
Spacing of tension bracing must be calculated based on neededstrength. In general, bracing is installed at 8' O.C. maximum.
* Simpson is a registered trademark of Simpson Strong-Tie Company, Inc.
Pre-cut structural blocking provides a quick andefficient method to prevent joist rotation.■ Economical alternative to strapping, x-bracing or tension bridging.
■ Pre-cut to fit 12”, 16”, 19.2” or 24” spacing.
■ Pre-punched holes for quick attachment.
■ Available in 18 gauge.StructuralBlocking
OvernightDelivery!
Available for
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 128
Floor Joist Hangers and Connectors
The Simpson* (S/ JCT) joist hanger provides maximuminstallation flexibility. This universal hanger can be used for8"–14" deep wood or steel framing members. The hangeris easily field skewable and can accommodate up to 45˚attachments. Floor joists can be attached from either sideor easily doubled up.
Each hanger is pre-punched with various shaped holes forfast, easy and accurate fastener placement. Round holes are used for minimum loads, and both round and triangleholes are used for maximum loads.
The SJCT joist hanger is typically used to hang joists fromwood, glue-lams, light-gauge steel or structural steel I-beams.
Simpson
®(SJC
T) 8–14 Hanger
129For more information or to contact a sales representative, see page 3
SJCT
* Simpson is a registered trademark of Simpson Strong-Tie Company, Inc.
DMF Simpson™ Thickness Weight/Piece PackagingProduct Reference Gauge Mils Design Thickness lbs kg Pcs/BoxCode Inches mmSJCT S/JCT8-14 14 68 0.0713 1.811 0.600 0.271 50
Simpson® (SJCT) 8-14 Hanger
OvernightDelivery!
Available for
This premier joist hanger features “one size fits all”flexibility and accommodates8"–14" deep floor joists.■ One size fits all. Eliminates numerous SKUs.
■ Field skewable up to 45˚.
■ Joists can be attached from either side or doubled up.
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 129
Sim
pson
®Br
idle
Han
ger
(SLB
V/SM
B)
130 The place to stop…before the building starts! SMrequest a quote online @
Traditional hanger used to attach floorjoists to structural steel beams.
■ Single-and double-wide hangers.
■ Stock sizes for 8”, 10”, 12” and 14”deep joists.
■ Other widths and depths available.
Simpson* bridle hangers are commonly used to attachlight-gauge C-joists to structural steel beams. Bridlehangers are easily attached with welds.
Bridle Hanger
Photo illustrates SJCT Hanger. Bridle Hanger is an acceptable alternative.
DMF Thickness Depth Width Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm Inches mm lbs kg Pcs/Code Inches mm Box
8 203 2 50.8 1.00 0.452 25
SLBV 14 68 0.0713 1.811 10 254 2 50.8 1.25 0.566 2512 305 2 50.8 1.50 0.679 2514 356 2 50.8 2.00 0.905 258 203 2 50.8 2.00 0.905 25
SMB 12 97 0.1017 2.583 10 254 2 50.8 2.25 1.018 2512 305 2 50.8 2.50 1.131 2514 356 2 50.8 4.00 1.810 25
Double-wide hangers available on request.
∅ Other style hangers are available.
*Simpson is a registered trademark of Simpson Strong-Tie Company, Inc.
Simpson* Bridle Hanger (SLBV/SMB)
OvernightDelivery!
Available for
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 130
Floor Joist Hangers and Connectors
This specialty hanger provides a quick, easy and versatile methodfor attaching steel rim joists to insulated concrete forms.■ Cost-effective connector used in ICF construction.
■ Anchors securely within the concrete.
■ Available in 14 gauge only.
Simpson
®Ledger C
onnector System (IC
FL)
131For more information or to contact a sales representative, see page 3
The Simpson* ledger connectorsystem is engineered to solve thechallenges of mounting steel orwood ledgers to insulated concreteform (ICF) walls. Simpson’s LedgerConnector System is easy, quickand versatile to use. Theperforations in the embedded legof the ICFL permit the concrete toflow around it, anchoring the ICFLsecurely within the concrete. Theexposed flange provides astructural surface for mountingeither a wood or steel ledger.
Ledger Connector
* Simpson is a registered trademark of Simpson Strong-Tie Company, Inc.
DMF Thickness Weight/Piece PackagingProduct Gauge Mils Design Thickness lbs kg Pcs/Code Inches mm BoxICFL 14 68 0.0713 1.811 1.81 0.82 20
Simpson® Ledger Connector System (ICFL)
OvernightDelivery!
Available for
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 131
Sim
pson
®Sk
ewab
le A
ngle
Han
gers
(SL
S5/S
LS7)
132 The place to stop…before the building starts! SMrequest a quote online @
Skewable utility angle used for rigid andoff-angle attachments of joists to joistsor other structural steel members.
■ Adjustable from 0˚ to 135°.
■ Bend one time only.
■ Available in 18 gauge.
■ ICBO ER 5275 recognized.
Simpson* SLS5/SLS7 skewable utility anglesare used to make rigid attachments of joist-to-joist or joist-to-other-miscellaneousframing. This clip is ideal for making off-angle attachments. It is easily field bentfrom 0˚ to 135˚.
CAUTION: This clip can only be bent one time.
SLS5
SLS7
*Simpson is a registered trademark of Simpson Strong-Tie Company, Inc.
DMF Thickness Size Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm lbs kg Pcs/Code Inches mm BoxSLS5 18 43 0.0451 1.146 4-7/8 124 0.300 0.136 100SLS7 18 43 0.0451 1.146 6-3/8 162 0.400 0.181 50
Simpson® Skewable Angle Hangers (SLS5/SLS7)
OvernightDelivery!
Available for
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 132
Floor Joist Hangers and Connectors
The LTP4 Lateral Tie Plate transfersshear forces from the joist rim orblocking to the sill plate.■ Prepunched holes for connection accuracy.
■ ICBO ER 5670 recognized.
The Simpson* LTP4 Lateral TiePlate transfers shear forces fromthe joist rim or blocking to the sillplate. Nail holes are spaced toprevent wood splitting for singleand double top plate applications.May be installed over plywoodsheathing.
Lateral Tie Plate (LTP4)
133For more information or to contact a sales representative, see page 3
Lateral Tie Plate
DMF Thickness Height Width Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm Width mm lbs kg Pcs/Code Inches mm BoxLTP4 20 33 0.0346 0.879 3 76.2 4-1/4 108 0.110 0.050 200
*Simpson is a registered trademark of Simpson Strong-Tie Company, Inc.
Lateral Tie Plate (LTP4)
OvernightDelivery!
Available for
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 133
Foun
datio
n C
lips
(FD
CL)
134 The place to stop…before the building starts! SMrequest a quote online @
Used to secure TradeReady® Rim,structural track, end caps or paralleljoists to the building foundation.■ Pre-punched for easy and accurate fastener placement.
■ Elongated slot provides for adjustable attachment to the foundation anchor bolts.
■ 16 gauge, G 90, 50 ksi steel.
Dietrich Foundation Clips are used toprovide a strong, rigid attachment ofTradeReady® Rim or conventionalstructural track to the buildingfoundation. Foundation clips aresecured to the foundation using theelongated slots, and anchor bolts. Thepre-punched leg is screw attached to theface or web of the joist. Clip spacing isbased on loading requirements.
Foundation Clip
DMF Thickness Width Height Length Weight/Piece PackagingProduct Gauge Mils Design Thickness Inches mm Inches mm Inches mm lbs kg Pcs/Code Inches mm Box
FDCL 16 54 0.0566 1.438 5 127 5-1/2 140 5 127 0.900 0.407 80
Foundation Clips (FDCL)
OvernightDelivery!
Available for
10447 Floor Framing 116-117:DMF07_100-101 7/6/10 9:19 AM Page 134
135
Light-Gauge Metal TrussesPrefabricated/Factory-Assembled Metal Trusses ............................138–139C-Truss ....................................................140Simpson® Seismic and Hurricane Ties (SH-Series) ..................................140
135-140 Truss Framing:DMF07_120-121 7/6/10 2:09 PM Page 1
Trus
s Fr
amin
g O
verv
iew
Advantages
Light-gauge steel trusses offer many advantagesover traditional roof framing components. Becauseof steel’s incredible strength, light-gauge trussescan be designed for clear spans over 100'. They caneliminate intermediate bearing walls and createlarge open spaces. Steel trusses not only span far-ther, they permit wider on-center spacing thatresults in additional labor and material savings.
One of steel’s greatest benefits is noncombustibil-ity. Steel will not burn, and does not add fuel to a burning fire. Steel trusses are fully non-combustible and meet even the most stringent fire codes. In many cases they reduceinsurance premiums and possibly eliminate expensive sprinkler systems.
In general, steel provides straighter, tighter and truer framing, resulting in better, longterm performance. Steel isn’t susceptible to rot, insects or mold. It doesn’t warp, twist,bow, shrink or swell like its wood counterpart. Ceilings remain flat, even and virtuallyfree from unsightly cracks and “nail pops.”
Light-gauge trusses can be field assembled using conventional C-studs, or they can beprefabricated in controlled factory environments and delivered directly to your jobsite.Prefabricated trusses offer many advantages over field assembled trusses includingshorter construction cycles, higher quality and consistency.
Metal Truss Fabrication Options
Dietrich Metal Framing provides a number of light-gauge metal truss options to meet your specificrequirements, including prefabricated or field-assembled C-stud trusses.
AEGIS Metal Framing, our joint venture companywith Mitek, provides pre-engineered, prefabricat-ed and UL* rated trusses that are delivered to yoursite ready for installation. The AEGIS** interna-tional fabrication network uses state-of-the-art
AEGIS® software to accurately bid and fabricate a complete truss system. AEGIS™ fabri-cators also provide sealed truss design drawings. Depending on the job requirements,your AEGIS® fabricator can also provide certified permanent bracing and connectiondesign. Many AEGIS® fabricators can also provide truss installation.
C-stud field-cut and field-assembled trusses provide another option for light-gaugetrusses. C-stud assemblies require independent design drawings by engineering compa-nies like Dietrich Design Group. Dietrich Design Group can also provide fabricationdrawings for an additional fee.
TRUSSFRAMINGOVERVIEW
Light-gauge steel trusses are an eco-nomical, lightweight rigid roof fram-ing system used in educational,assisted living, hotels/motels, military,industrial and countless other com-mercial and institutional structureswhen a “residential look and feel” isdesired. Steel trusses are also used inresidential roof and floor assemblies.They provide fully noncombustibleassemblies that meet required firecodes. They are the ideal, cost-effec-tive alternative to structural steel,bar joist and fire-retardant woodtrusses. Steel trusses are compatiblewith almost every construction type,method or system including light-gauge steel, structural steel, CMU,concrete and wood framing.
Light-gauge steel trusses have thedesign flexibility to accommodatealmost any roof line including com-plex roof geometries. Some of themore common truss styles includefink, fan, pratt, king, flat, gable, hip,mansard, mono, cantilever, over-hang and scissor trusses. Light-gaugecomponents can also be assembled toprovide open web floor trusses.
*UL is a trademark of Underwriters Laboratories, Inc.
**AEGIS is a trademark and tradename of AEGIS Metal Framing, LLC.
136 The place to stop…before the building starts! SMrequest a quote online @
136-137 Truss Framing:DMF07_120-121 7/6/10 2:01 PM Page 136
Overview
Light-Gauge Metal Truss TypesPitched or common truss is characterized by its triangular shapeand is most often used in roof construction.
Other Types Of Trusses Include:
Flat or parallel chord truss is most often used in floor or flat roof construction.
Top Chord-Bearing Floor Truss With Chase
Bottom Chord-Bearing Floor Or Roof Truss
(can design with a chase as well)
Scissors
Vaulted Parallel Chord
Vault
Gambrel Cantilevered Mansardw/Parapets
Flat Vault
Studio VaultBowstring
Dual Pitch
Tray Or Coffer
Barrel Vault
Multi Piece Double Inverted
Double Cantilever
Mono
HalfScissors
Half Hip
SlopingFlat
Tri-Bearing
Room-In-Attic
Hip
Polynesian Celestory
Truss Framing O
verview
137For more information or to contact a sales representative, see page 3
136-137 Truss Framing:DMF07_120-121 7/6/10 2:01 PM Page 137
Pref
abric
ated
/Fac
tory
-Ass
embl
ed M
etal
Tru
sses
The remarkable Ultra-Span***light-gauge steel truss systemfrom AEGIS™ offers the safest,most cost-effective way to putcompletely non-combustible sloped roofs on commercialstructures. Our international network of fabricators canprovide a fully engineered, pre-fabricated, UL™ listed*, light-gauge system for almost any roof you can imagine.
When specifying and purchasing light-gauge steel trussesfor your next commercial/institutional project, be sure toinsist on the most comprehensive system available today.The Ultra-Span® System from AEGIS® Metal Framing offersbuilding designers and contractors real peace of mind thatcomes from knowing all the key elements of a properlyfunctioning structural system are designed and provided for.
When you select an authorized Ultra-Span® fabricator todesign and manufacture your prefabricated truss system,you are selecting an experienced truss specialist. Utilizingthe state-of-the-art AEGIS® suite of software, an Ultra-Span®
fabricator can efficiently and accurately bid a completetruss system that can include all the following items:
• All the trusses, including girders, valleys andspecials.
• Truss-to-truss and truss-to-bearing connections.• Special connections.• Truss bracing and installation bracing products.• Permanent bracing.• Hip, ridge and valley plates.
Computer designed for precision and factory built for qualityand consistency, prefabricated Ultra-Span® trusses are theideal, cost-effective alternative to structural steel, bar joist, fire-treated wood and site-assembled cold-formed metal framing.
AEGIS® Metal Framing, LLC, is a joint venture between theworld’s largest producer of metal framing products andaccessories (Dietrich) and the world’s leading provider ofproducts, software and engineering services for the pre-fabricated building components industry (Mitek). The AEGISmission is to dramatically increase the use of computerdesigned, factory-built light-gauge metal roof, floor and wallframing systems in commercial, institutional and residentialconstruction.
Contact your local AEGIS® fabricator or AEGIS MetalFraming for more information on the comprehensive Ultra-Span® system!
AEGIS* prefabricated trusses arepre-engineered, UL™ listed, factory-assembled framing systems shipped to the jobsite.■ AEGIS® fabricators do all the work from
estimating, designing, assembly and delivery.
■ Pre-engineered and prefabricated by trussprofessionals.
■ Greatly reduces construction time.
■ UL** listed assemblies.
■ International fabrication network.
■ Limitless designs and possibilities.
138 The place to stop…before the building starts! SMrequest a quote online @
*AEGIS is a trademark and trade name of AEGIS Metal Framing, LLC**UL™ and UL Listed are trademarks of Underwriters Laboratories, Inc.***Ultra-Span is a registered trademark of AEGIS Metal Framing, LLC
136-137 Truss Framing:DMF07_120-121 7/6/10 2:01 PM Page 138
Light-Gauge Metal Trusses
USJ
USC
Prefabricated/Factory-Assembled M
etal Trusses
138For more information or to contact a sales representative, see page 3
USW
136-137 Truss Framing:DMF07_120-121 7/6/10 2:01 PM Page 139
C-T
russ
& S
imps
on®
Seis
mic
and
Hur
rican
e Ti
es (
SH-S
erie
s)
Simpson® Seismic and Hurricane Ties are designed toprovide wind and seismic ties for trusses and rafters. Theseversatile products can also be used for general tie-downpurposes, strong back attachments and as all-purpose tieswhere one member crosses another.
■ Pre-punched for fast and accurate fastener placement.
■ Ties are shipped in equal quantities of separate rights and lefts.
■ Simpson* recognized quality.
C-Stud/field-assembled metal trussesare lightweight, economical roofframing systems used in educational,assisted living, hotels/motels, military,industrial and countless othercommercial and institutionalstructures when a “residential lookand feel” is desired. Steel trusses arealso used in residential roof and floorassemblies. They are the ideal, cost-effective alternative to structural steel,bar joist and fire-retardant woodtrusses. Steel trusses are compatiblewith almost every construction type,method or system including light-gauge steel, structural steel, CMU,concrete and wood framing.
C-Stud components are field cut and assembled to providenoncombustible roofassemblies.■ Standard framing components.
■ Noncombustible assembly.
■ Lightweight and easy to handle.
■ Clear spans up to 100’.
■ Limitless designs and possibilities.
Used to attach and tie trusses and rafters to the building structure.
Typically, field-assembled C-stud roof assemblies aredesigned by Dietrich Design Group or another qualifiedlight-gauge design company. Trusses are fabricatedonsite using conventional C-studs. C-studs are used forboth top and bottom cords as well as web members.Members are secured back to back using screws orwelds. When C-studs are used in truss applications, theyshould be ordered as unpunched. Care must be taken toinsure proper bracing and connections.
SH2 SH3
*Simpson is a registered trademark of Simpson Strong-Tie Company, Inc.
C-Stud Truss
Gusset Plates
140 The place to stop…before the building starts! SMrequest a quote online @
136-137 Truss Framing:DMF07_120-121 7/6/10 2:02 PM Page 140
141
Shaftwall/StairwellShaftwall/Stairwell 2-Hour Fire-Rated Assemblies CT Stud (CT) ........................................144Shaftwall/Stairwell 2-Hour Fire-Rated Assemblies J-Runner (TT) ......................................145Area Separation WallH-Stud Area Separation Wall System H-Runner/C-Runner (HRN) ................................146H-Stud Area Separation Wall System H-Stud (HSN) ......................147Aluminum Breakaway Clips (AB)..147Head of WallSLP-TRK® Slotted Track (BDTK)......148
Photo courtesy of BPB America
141-148 Fire-Rated Assemblies:DMF07_125 7/6/10 4:13 PM Page 141
Fire
-Rat
ed A
ssem
blie
s O
verv
iew
Shaftwall/Stairwell
Cavity shaftwall systems are nonload-bearing firerated wall assemblies that provide critical, lifesafety, fire-resistant protection for elevatorshafts, stairwells, vertical chases and mechanicalenclosures. Shaftwalls in elevators and stairwellsare one of the most important wall assemblies ina building. They provide the only means ofhuman egress from the building in an emer-gency. Vertical chases and mechanical enclosureskeep vital communication, power, water, fresh airand exhaust systems intact when a fire occurs.
Cavity shaftwalls are constructed utilizing one oftwo methods: masonry/CMU or light-gauge steeland gypsum. Gypsum drywall shaftwall construc-tion has become the preferred and most widelyused shaftwall assembly. These shaftwalls arelightweight, install faster, and provide lower in-place costs. They also significantly reduce struc-tural framing and foundation costs. Masonryshaftwalls in high-rise buildings historically weighbetween 20 and 45 lbs. per square foot comparedto gypsum assemblies that weigh between 10 and13 lbs. per square foot.
In addition to substantial weight reduction, gypsum shaftwall assemblies can beinstalled from the exterior of the shaft at each floor, eliminating the need for scaf-folding. Shaftwall installation is easy, quick and clean. Light-gauge steel and gypsumassemblies provide fast, lightweight, low-cost and high-performance assemblies.
FIRE-RATEDASSEMBLIES
OVERVIEWFire-rated assemblies provide critical,life safety fire-resistant protection in avariety of wall assemblies in many dif-ferent building types. These assembliescan be constructed from a myriad of dif-ferent building materials. Some of themost common include masonry and acombination of steel and gypsum.
Steel and gypsum assemblies havebecome the preferred and most widelyused fire-rated assemblies. They arelightweight, low-cost, high-performancesystems that significantly reduce overallbuilding weight and construction time.Two of the most common fire-ratedassemblies are Area Separation Wallsand Cavity Shaftwalls.
Area Separation Walls are typically usedto provide two-hour fire-rated protec-tion between adjacent living units inapartment buildings, condominiums,townhouses and multifamily construc-tion. Cavity Shaftwalls are commonlyused to provide fire-resistant protectionfor elevator shafts, stairwells, verticalchases and mechanical enclosures inmost multi-story structures. Cavityshaftwall systems are widely used in low-rise, mid-rise and high-rise buildings.
Dietrich Metal Framing provides fullytested and approved assemblies for botharea separation wall and cavity shaft-wall construction. What makes theDietrich system unique is that it has beentested with almost every gypsum boardand shaft liner manufacturer in thecountry. Unlike competing systems, theDietrich CT Cavity Shaftwall and H-StudSystems provide maximum flexibility tochoose from a variety of board manufacturers. Other systems are onlytested with one company.
This unprecedented flexibility meansquick availability of product at econom-ical costs. It provides you with a choiceand peace of mind knowing you’reusing a tested and approved assembly.
Photo courtesy of BPB AMERICA
Photo courtesy of National Gypsum
142 The place to stop…before the building starts! SMrequest a quote online @
141-148 Fire-Rated Assemblies:DMF07_125 7/6/10 4:13 PM Page 142
Overview
AreaSeparationWall
Area Separation Wallsare nonload-bearing 2-hour rated vertical wallassemblies that providefire-resistant protectionbetween adjacent livingunits in apartment
buildings, condominiums and townhouses. Area SeparationWalls are also referred to as party walls, firewalls, multi-fam-ily walls and H-Stud assemblies.
Area Separation Walls are assembled between two independ-ent walls to form a commonly shared party wall that extendsfrom the foundation through the roofline. The walls areassembled with two 1" thick gypsum panel liners verticallyinstalled between 2" H-Studs spaced 24" O.C. C-Runners or H-Tracks are installed at the top and bottom of the walls andback-to-back between vertically stacked panels. Overallstacked area separation wall assembly cannot exceed 50'.
Aluminum Breakaway Clips are used to secure the AreaSeparation Wall in place to both sides of the floor, roof andtruss line. The clips on the fire side are intended to meltunder the intense heat during a fire, thus enabling a fire-damaged structure to collapse while keeping the fire wallbarrier in place to protect the adjacent unit. This is com-monly referred to as a “controlled collapse.”
Area Separation Wall assemblies are a great alternative tomasonry construction. The H-stud system is at least 50%lighter than masonry walls, installs faster, is STC sound ratedand increases valuable floor space compared to 8" – 12"wide masonry walls.
Head of Wall
It’s a real challenge these days meeting head-of-wall codesfor fire stop and life safety while maintaining the ability toabsorb vertical movement in high-rise buildings. SLP-TRK®
slotted track is the solution. SLP-TRK® slotted track providesa positive attachment for wall strength and allows for verti-cal movement.
SLP-TRK® Systems comply with the toughest fire coderequirements in North America, if not the world. It has beentested with a variety of leading fire-stop products, and hasoutperformed the requirements of stringent fire and hosestream testing ASTM E 119, ASTM E 814. SLP-TRK® slottedtrack also has met and exceeded the latest seismic cyclingstandards found in UL2079 and ASTM E 1966. SLP-TRK® cur-rently has over 100 UL™ listings.
“Dietrich’s shaftwall systemgives me the flexibility to choose from a variety of gypsum companies, which means more profit to my bottom line.”— Brad Bryant, Baker Drywall
Dallas, TX
* SLP-TRK® is a registered trademark of Sliptrack Systems, Inc.
Fire-Rated Assemblies O
verview
143For more information or to contact a sales representative, see page 3
141-148 Fire-Rated Assemblies:DMF07_125 7/6/10 4:13 PM Page 143
Shaf
twal
l/St
airw
ell 2
-Hou
r Fi
re-R
ated
Ass
embl
ies
CT
Stud
(C
T-Se
ries™
)
144 The place to stop…before the building starts! SMrequest a quote online @
Dietrich CT Cavity Shaftwall Studs are rigid high- performancemembers engineered to maintain shaftwall integrity. CT Studs areavailable in 2-1/2", 4" and 6" wide members. CT Studs arepunched with 1" circular knockouts at 12" O.C. for easyinstallation of conduit or other mechanical service lines.
A unique feature of the CT Stud is the slotting in the web of the stud. Independent laboratory tests havedemonstrated that these slots improved resistance to thermal and noise transmissions effectively.
CT Studs are designed for use with 1" thick Gypsum LinerPanels. CT Studs are friction-fitted between top and bottom J-Tabbed Track. Gypsum liner panels are inserted into the studflanges. The flanges provide an airtight friction fit along the length of the panel that eliminates rattling. Studs areautomatically spaced 24" O.C. maximum once 1" shaft linerpanels are friction-fit into place. The system is finished withone or two layer(s) of gypsum board to complete and achievethe designated fire rating.
Dietrich CT Cavity Shaftwall System is tested with the following manufacturers: United States Gypsum; James Hardie; CertainTeed; National Gypsum; American; Eagle; Georgia-Pacific; Standard;Lafarge Gypsum; Temple; PABCO
CT Cavity Shaftwall Studs are used to provide high-performance fire-rated elevator, stairwell, chase and mechanical shafts.■ Fire-rated assemblies.
■ Slotted webs to reduce thermal and noise transmission.
■ Engineered to maintain shaftwall integrity.
■ Pre-punched for horizontal service lines.
■ Fully tested with most major gypsum manufacturers.CT Stud
DMF C-T Stud Nominal Design Weight* Areas Ix SxProduct Depth Gauge Thickness (lb/ft) (in2) (in4) (in3) Pcs/SkidCode (in)CTN2 2-1/2" 25 0.0230 0.514 0.165 0.164 0.114 210CTE2 2-1/2" 20 0.0346 0.805 0.248 0.241 0.168 210CTN4 4" 25 0.0230 0.622 0.199 0.480 0.209 160CTE4 4" 20 0.0346 0.974 0.298 0.710 0.309 160CTE6 6" 20 0.0346 1.200 0.367 1.858 0.547 84
* Weight is based on minimum delivered thickness.
Gross Section Properties
141-148 Fire-Rated Assemblies:DMF07_125 7/6/10 4:13 PM Page 144
Shaftwall/StairwellShaftw
all/Stairwell 2-H
our Fire-Rated Assemblies J-Tabbed Track (TT)
145For more information or to contact a sales representative, see page 3
Dietrich J-Tabbed Track is used at the floor and ceiling inshaftwall assemblies. CT studs and gypsum shaftliner panelsare friction fit between the top and bottom J-Tabbed Track. J-Tabbed Tracks have unequal legs. The longer leg (availablein 2-1/4" and 3") is installed with the longer leg against theshaft. The leg provides a backstop for easy installation of theshaftliner. Three-inch leg track is typically used as jamb strutsaround closure details, including duct and door openings,abutments and intersections.
Dietrich J-Tabbed Track is punched with fold-up tabs every12". The tabs are easily folded upward to secure gypsumpanel liners in closure details. These tabs reduce framingcomponents compared to other competing assemblies andpermit faster and more-efficient installation.
Universal tabbed track secures CT studs and gypsum shaftliner panels in shaftwall assemblies.■ Punched tabs to secure panels in vertical
and closure details.
■ Designed for multiple uses.
■ Standard 10’ length. Custom lengths available.J-Tabbed Track
DMF Thickness Size Weight PackagingProduct Gauge Mils Minimum Thickness lbs/ft Pcs/Code Inches mm
Width LE6Skid
2-1/2"2-1/4" 0.410 180
3" 0.467 180
TTN (2,3)* 25 21 0.021 0.533 4"2-1/4" 0.514 144
3" 0.572 144
2-1/2"2-1/4" 0.642 180
3" 0.732 180
TTE (2,3)* 20 33 0.0329 0.836 4"2-1/4" 0.805 144
3" 0.896 144
6"2-1/4" 1.037 108
3" 1.122 108
*2 designates 2-1/4" leg.*3 designates 3" leg.Note: Revised ICC Report PendingFor installations requiring compliance with NER506, special order products are required.Request 20 gauge C-T studs and J-track with design thickness = 0.040 inches.
J-Tabbed Track/J-Runner (TT)
141-148 Fire-Rated Assemblies:DMF07_125 7/6/10 4:14 PM Page 145
H-S
tud
Area
Sep
arat
ion
Wal
l Sys
tem
H-T
rack
/C-R
unne
r (H
RN)
146 The place to stop…before the building starts! SMrequest a quote online @
Dietrich C-Runner, also referred to as H-Track, is used to secure H-Stud and gypsum shaftliner panels in areaseparation wall assemblies. C-Runner is attached to thefoundation with power-driven fasteners. C-Runner is alsoused as top track to cap the H-stud and gypsum shaftlinerpanels. A second track is then screwed back to back, to thelower runner, to hold the next level of the area separationwall assembly. Area Separation Wall assemblies are limited to50' in height (maximum).
C-Runner or H-Track is used at the top and bottom of vertical panels to secure shaftliner panels and H-Studs in area separation wall assemblies.■ 2-hour fire-rated assembly.
■ 2” wide and 25 gauge.
■ Tested and approved with most major gypsum and shaftliner manufacturers.
■ Standard 10’ stock length.
■ ICC approved—Evaluation Report 92-19. H-Track/C-Runner
Although this was a tragic event, it clearly proves the effectivenessof the Area Separation Wall system. The system performed asdesigned by maintaining the integrity of the fire wall protectingthe lives and property of the adjacent units.
Photo courtesy of National Gypsum
DMF Thickness Size Weight PackagingProduct Gauge Mils Design Thickness Width Length lbs/ft kg/m Pcs/ Pcs/Code Inches mm Inches mm ft m Bundle SkidHRN1
25 18 0.0188 0.478 2-1/8 54.08 2.44 0.270 0.400
NA560
(C-Runner) 10 3.05 0.270 0.400 560
C-Runner (HRN)
141-148 Fire-Rated Assemblies:DMF07_125 7/6/10 4:14 PM Page 146
Area Separation WallH
-Stud Area Separation Wall System
H-Stud (H
SN) & Alum
inum Breakaw
ay Clips (AB)
147For more information or to contact a sales representative, see page 3
H-Studs are a key framing component and add structural integrity to area-separation wall assemblies.
Dietrich aluminum breakaway clips are used as part of the H-Stud Area Separation Wall assembly and are designed to meltand break away when exposed to fire. The clips are used tohold the Area Separation Wall assembly in place at the floorroof and truss line between adjacent units. Should a fire break
out in one unit, the Aluminum Breakaway Clips on the fire-ridden side of the Area Separation Wall will melt, allowing thewall structure for that side to collapse. The breakaway clips onthe non-fire side will remain intact and hold the AreaSeparation Wall in place as a barrier to contain the fire to theunit of origin.
Clips melt away under intense heat,allowing a fire-damaged structure tocollapse while keeping the firewall barrierin place to protect the adjacent units.■ Tested and approved with most major gypsum and shaftliner manufacturers.
■ Clips measure 2” x 2” x 2-1/2”.
H-Stud■ 2-hour fire-rated
assembly.
■ 2” wide and 25 gauge.
■ Tested andapproved with most major gypsumand shaftlinermanufacturers.
■ Stock lengths are 8’, 10’ and 12’.
■ ICC approved.Evaluation Report92-19.
Dietrich H-Studs are 2" wide vertical membersused to secure two 1" thick pieces of gypsumshaftliner in Area Separation Wall assemblies. H-Studs are inserted into C-Runners and slid overgypsum panel liner edges. The process isrepeated until the desired wall length is achieved.Once the wall is plumbed it is secured at the floor,roof and truss line with aluminum breakawayclips. Wall assemblies may be built to heights of10' between floors and stacked to a totalmaximum height of 50'.
DMF Thickness Size Weight PackagingProduct Gauge Mils Design Thickness Width Length lbs/ft kg/m Pcs/ Pcs/Code Inches mm Inches mm ft m Bundle Skid
HSN8 2.44 0.44 0.656 300
(H-Stud)25 18 0.0188 0.478 2-1/16 52.4 10 3.05 0.44 0.656 NA 300
12 3.66 0.44 0.656 300
H-Stud (HSN)
DMF Size Thickness PackagingProduct Inches mm in m Pcs/BoxCodeAB 2 x 2 x 2-1/2 50.8 x 50.8 x 63.5 0.050 1.27 500
AB63* 2 x 2 x 2-1/2 50.8 x 50.8 x 63.5 0.063 1.60 500*AB63 meets requirements of ICC-ES Legacy Report 92-19
Aluminum Breakaway Clip (AB)
141-148 Fire-Rated Assemblies:DMF07_125 7/6/10 4:14 PM Page 147
SLP-
TRK®
Slot
ted
Trac
k (B
DTK
)
148 The place to stop…before the building starts! SMrequest a quote online @
It’s a real challenge thesedays meeting head-of-wallcodes for fire stop and lifesafety while maintaining theability to absorb verticalmovement in low-, mid-, and high-risebuildings. SLP-TRK® slottedtrack is the solution.
SLP-TRK® slotted trackprovides a positive attachment for wall strength and allows forvertical movement. Movement caused by normal head-of-wall andfloor extension or compression is absorbed by SLP-TRK® slottedtrack to prevent damage to the wall assembly.
SLP-TRK® slotted track smoothly integrates with a variety ofwall-installation systems and is extremely user-friendly aswell as economical. The simple design and easy installationreduces the cost of materials and labor.
SLP-TRK® systems comply with the toughest coderequirements in the country, if not the world. They havebeen tested with a variety of leading fire-stop products, and have outperformed the requirements of stringent fireand hose stream tests ASTM E 119, ASTM E 814. SLP-TRK®
also has met and exceeded the latest seismic cyclingstandards found in UL2079 and ASTM E 1966.
Meeting Code Requirements
SLP-TRK® slotted track has achieved the following buildingcode approvals:
ICBO-ER 5344UL Listed R19236UL Certified for Canada XHL17LA City RR25344OSHPD R#0371NY City MEA 285-01-M
SLP-TRK® slotted track meetsrequirements of all standardbuilding codes:
IBC; BOCA; SBCCI; UBC
In addition, SLP-TRK complies with the requirements of ASTM and UL2079.* SLP-TRK is a registered trademark of Sliptrack Systems, Inc.
** UL and UL Listed are registered trademarks of Underwriters Laboratories, Inc.
Most cost-effective, positively attachedfire-rated deflection system.■ Positive attachment that allows up to 1” of vertical movement.
■ Meets BOCA, SBCCI, ASTM, UL2079, IBC and UBC building codes and standards.
■ UL™** approved 1- and 2-hour systems.
■ Single-track assembly.
System 1 – W.R. GraceWHI-495-PSV-1201
System 2 – W.R. GraceWHI-495-PSV-1333
System 3 – IsolatekWHI-495-PSV-1333System 4 – Isolatek WHI-495-PSV-1334
System 5 – IsolatekWHI-495-PSV-1333
System 6 – W.R. GraceWHI-495-PSV-1338
SLP-TRK® Systems — Fire-Rated AssembliesSystem 1-6 Warnok Hersey/ITS ICBO ESER-5344
System 7STI
UL-HW-D-0003UL-HW-D-0034UL-HW-D-0043UL-HW-D-0044UL-HW-D-0054UL-HW-D-0079UL-HW-D-0088UL-HW-D-0099UL-HW-D-0102UL-HW-D-0136UL-HW-D-0137UL-HW-D-0152UL-HW-D-0153UL-HW-D-0194UL-HW-D-0210UL-HW-D-0241UL-HW-D-0242UL-HW-D-0243UL-HW-D-0260UL-HW-D-0363UL-HW-D-0365UL-HW-D-0371
System 8PFPP
UL-HW-D-0024UL-HW-D-0025UL-HW-D-0036UL-HW-D-0062UL-HW-D-0063UL-HW-D-0071UL-HW-D-0072UL-HW-D-0073UL-HW-D-0162UL-HW-D-0185UL-HW-D-0191UL-HW-D-0271UL-HW-D-0272UL-HW-D-0263UL-HW-D-0278
System 93M
UL-HW-D-0020UL-HW-D-0021UL-HW-D-0029UL-HW-D-0031UL-HW-D-0101UL-HW-D-0111UL-HW-D-0134UL-HW-D-0170UL-HW-D-0173UL-HW-D-0205UL-HW-D-0265
System 10HILTI
UL-HW-D-0042UL-HW-D-0045UL-HW-D-0046UL-HW-D-0049UL-HW-D-0076UL-HW-D-0077UL-HW-D-0082UL-HW-D-0083UL-HW-D-0084UL-HW-D-0085UL-HW-D-0087UL-HW-D-0089UL-HW-D-0106UL-HW-D-0154UL-HW-D-0184UL-HW-D-0190UL-HW-D-0218UL-HW-D-0259UL-HW-D-0313UL-HW-D-0321UL-HW-D-0322UL-HW-D-0324
System 11Johns-ManvilleUL-HW-D-0047UL-HW-D-0048UL-HW-D-0067UL-HW-D-0068UL-HW-D-0069UL-HW-D-0167UL-HW-D-0186UL-HW-D-0193UL-HW-D-0195UL-HW-D-0275UL-HW-D-0277
System 12Rectorseal
UL-HW-D-0032UL-HW-D-0033UL-HW-D-0058UL-HW-D-0059UL-HW-D-0104UL-HW-D-0105UL-HW-D-0127UL-HW-D-0128UL-HW-D-0129UL-HW-D-0130UL-HW-D-0179UL-HW-D-0180UL-HW-D-0221UL-HW-D-0222UL-HW-D-0297UL-HW-D-0298
System 13GRACE-
FlamesafeUL-HW-D-0107UL-HW-D-0108UL-HW-D-0124UL-HW-D-0144UL-HW-D-0146UL-HW-D-0147UL-HW-D-0148UL-HW-D-0165UL-HW-D-0213UL-HW-D-0217UL-HW-D-0219UL-HW-D-0257UL-HW-D-0299
System 14EGS Nelson
UL-HW-D-0223UL-HW-D-0224UL-HW-D-0227UL-HW-D-0228UL-HW-D-0238UL-HW-D-0239UL-HW-D-0283UL-HW-D-0288UL-HW-D-0304UL-HW-D-0305UL-HW-D-0309UL-HW-D-0310
System 15Tremco
UL-HW-D-0016UL-HW-D-0091UL-HW-D-0255UL-HW-D-0256UL-HW-D-0291
System 16JohnWagner
Assoc.UL-HW-D-0353UL-HW-D-0356UL-HW-D-0357UL-HW-D-0358UL-HW-D-0368UL-HW-D-0370
System 17A/D Fire
ProtectionSystems
UL-HW-D-0247UL-HW-D-0249UL-HW-D-0314UL-HW-D-0315UL-HW-D-0316UL-HW-D-0317UL-HW-D-0320
System 18OSI Sealants Inc.UL-HW-D-0183UL-HW-D-0341
System 19USG
UL-HW-D-0160
= ShaftwallSystem
SLP-TRK*
141-148 Fire-Rated Assemblies:DMF07_125 7/6/10 4:14 PM Page 148
149
Metal Corner Beads103 Deluxe® Corner Bead (CBU) 152Quicksilver™ Corner Bead (CBS)....153120/135˚ Corner Bead (CB12) ....153Bullnose 90˚ (CBB)............................154Bullnose Splayed 135˚ (CBBW)....155Bullnose Kerfed (CBBK) ..................156“J” Round™ Bullnose (JRND) ..........157Bullnose Corner and Transition Caps2-Way Metal Corner Cap 90˚ (MBC2) ..................................................1583-Way Metal Corner Cap 90˚ (MBC3) ..................................................158Bullnose to 90˚ Transition Cap (M859) ..................................................159Clinch-On Products, Co. Corner BeadsCorner Bead/Electro (CBCO) ........160Corner Bead/Hot-Dipped (CBCS) 161Corner Bead/Smooth (CBCP) ......162Splayed Corner Bead Hot-Dipped(CBCW) ..................................................163Hot-Dipped Bullnose (CBBC) ........164Painted 3/4" Bullnose Splayed Bead(CBPS) ....................................................165Hot-Dipped 3/4" Bullnose Splayed(CBSB) ....................................................166Painted 3/4" Bullnose (CBPB) ......167Metal Trims and Finishing ProductsMetal J-Trim (M400 Series™) ..........168Metal U-Trim/Spackle J (M20A)....169Metal L-Trim (M20B)..........................170093 Zinc Control Joint (ZNCJ) ......171Mini-Bead™ 800 (MB80/ZB80) andMini-Bead™ 900 (MB90/ZB90) ....172
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:39 PM Page 149
Met
al B
eads
& T
rims
Ove
rvie
w
150 The place to stop…before the building starts! SMrequest a quote online @
METAL BEADS & TRIMS
OVERVIEWMetal drywall beads and trims aretraditional reinforcement and finish-ing products used in gypsum wall-board construction. Metal beads andtrims provide crisp, clean and straightprotection for drywall corners. Themost common metal trim is drywallcorner bead. Corner bead is appliedto 90˚ exposed outside gypsum cor-ners to provide a strong, durable,straight, crisp finished corner.
Metal beads and trims are available ina wide selection of products and sizesto finish almost any drywall finishcondition. Metal beads and trims arenailed, screwed, stapled or clinched inplace and finished with joint com-pound. They are low cost, easilyapplied and provide high-quality, longlasting professional finishes.
Advantages
Durable—Metal beads and trims provide strong, rigid, dent- and impact-resistantcorner and edge reinforcement.
Straight—Precision manufactured to exacting specifications to ensure straight,sharp and crisp edges and corners.
Corrosion Resistant—Electrogalvanized and hot-dipped coatings provide superior corrosion protection.
Economical—Cost-effective method to protect and finish drywall and veneer corners.
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:39 PM Page 150
OverviewM
etal Beads & Trims O
verview
151For more information or to contact a sales representative, see page 3
Styles & Types
103 Deluxe® andQuicksilver™ CornerBeads are galvanizedsteel angles that ensurestraight, protective, clean-finished drywall corners.The 103 Deluxe® brand isrecognized as the pre-mier drywall corner beadfinishing trim product.These beads may benailed, stapled or
clinched into place and are completely concealed with jointcompound.
120/135˚ Corner Bead, also referred to as Splayed or Off-Angle Bead, provides a clean, crisp finished look at off-anglewall intersections.
Bullnose Corner Bead is used to create a smooth, round-ed look to standard drywall corners. Bullnose adds contem-porary styling and a sense of openness to any room.
Corner and Transition Caps provide quick and efficientsolutions to finishing bullnose intersections or installation ofbaseboard or crown moldings. This eliminates mitering,gaps and caulking.
Clinch-On Products, Co. – The name is synonymous withpremium, high-quality finishing beads and trims. Theseproducts are recognized as premier metal corner reinforce-ments. Beads and trim provided by Clinch-On Products, Co.are available in the Midwest, South, Southeast, Northeastand Colorado.
Metal Trims providemaximum protection andneat finished edges togypsum panels aroundwindow and door open-ings. They also provide aclean trim line at inter-sections or where gyp-sum panels abut dissimi-lar surfaces such ascolumns and windowmullions.
Metal Trim 200-A is a U-shaped trim for use where the gyp-sum panel edge will be exposed. Installation of the 200series trim is completed with joint compound for a smoothready-to-paint surface.
Metal Trim 200-B is an L-shaped trim and is especially use-ful where gypsum panels butt against another surface plane.Installation of the 200 series trim is completed with jointcompound for a smooth, ready-to-paint surface.
Metal J-Trim 400 Series is J-shaped, reveal-type galvanizedsteel trim used for door or window openings. No finishingwith joint compound is required.
Mini-Bead™ 800 is a dual-purpose mesh corner bead suit-able for one-coat veneer plaster or standard drywall systems.It’s a galvanized steel outside corner reinforcement with 11⁄4"wide fine mesh expanded flange tapered along outer edgesfor improved finishing.
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:39 PM Page 151
103
Del
uxe®
Cor
ner
Bead
(C
BU
)
152 The place to stop…before the building starts! SMrequest a quote online @
103 Deluxe® corner bead providesdurable, straight and crisp, clean 90˚ outside finished drywall corners.■ Electrogalvanized coating for corrosion protection.
■ Superior compound adhesion.
■ Strong metal reinforcement for drywall corners.
■ Exposed nose of the bead resists impact andforms a screed for finishing.
103 Deluxe®
Dietrich 103 Deluxe® corner bead is used toprovide a high-quality finish and solidprotection at drywall corners. This traditionaldrywall finishing product is nailed, stapled,screwed or clinched into place. Flanges aredeeply knurled and perforated for excellentjoint compound adhesion.
103 Deluxe® corner bead (CBU) isconsidered the premier drywall finishingcorner bead product. This productcombines a unique manufacturing process,with specially enhanced electrogalvanizedsteel to provide consistent, high-qualityfinishing each and every time.
Clinch-OnProducts, Co.’sCornerbead ToolFaster...Tighter...More Exact!Available by the piece or pallet.
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Cartons/Code Inches mm ft–in m Box Skid
6–9 2.06 55.7 25.3 75 486–10 2.08 56.4 25.6 75 48
CBU 7–0 2.13 55.4 25.1 72 48103 Deluxe™ 1-1/4 x 1-1/4 31.8 x 31.8 8–0 2.44 55.4 25.1 63 48(Dull Finish) 9–0 2.74 55.4 25.1 56 48
10–0 3.05 55.0 24.9 50 4812–0 3.66 55.4 25.1 42 48
103 Deluxe™ Corner Bead (CBU)
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:39 PM Page 152
Metal Corner BeadsQ
uicksilver ™C
orner Bead (CB
S) & 120/135˚ Corner Bead (C
B12)
153For more information or to contact a sales representative, see page 3
Quicksilver™ metal corner bead is used to achieve durable,straight, and crisp, clean 90˚ outside finished drywall corners.
Dietrich’s 120/135˚ corner bead, also referred to as splayedor off-angle bead, provides a clean, crisp finished look at off-angle intersections. This traditional drywall finishing bead isnailed, stapled or screwed into place and finished with joint compound to provide a high-quality professional finish. Flanges are knurled and perforated to enhance compoundadhesion and the exposed nose forms a screed for finishing.
Superior finish and reinforcement for off-angle drywall corners.■ Electrogalvanized for superior compound adhesion.
■ Easy to attach and finish.
■ Galvanized for corrosion protection.
■ Hot-dipped galvanized coating.
■ Superior corrosion protection.
■ Strong metal reinforcement for drywallcorners.
■ Exposed nose of the bead resists impact andforms a screed for finishing.
Dietrich Quicksilver™ corner bead (CBS) is a hot-dipped,highly durable galvanized bead that offers superiorcorrosion protection. This bead is ideal for humid,moisture-prone conditions and high-traffic areas subject to more than normal abuse.
Recognized as a superior corrosion-resistant drywall finishing corner bead, Quicksilver™
corner bead provides a high-quality finish and solid protection at drywall corners. Thistraditional drywall finishing product is nailed, stapled, screwed or clinched into place.Flanges are deeply knurled and perforated for excellent joint compound adhesion.
Quicksilver™
SplayedCorner Bead
Clinch-OnProducts, Co.’sCornerbead ToolFaster...Tighter...More Exact!Available by the piece or pallet.
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Cartons/Code Inches mm ft–in m Box Skid
6–9 2.06 55.7 25.3 75 486–10 2.08 56.4 25.6 75 48
CBS 7–0 2.13 55.4 25.1 72 48Quicksliver™ 1-1/4 x 1-1/4 31.8 x 31.8 8–0 2.44 55.4 25.1 63 48
(Shiny Finish) 9–0 2.74 55.4 25.1 56 4810–0 3.05 55.0 24.9 50 4812–0 3.66 55.4 25.1 42 48
Quicksilver™ Corner Bead (CBS)
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Cartons/Code Inches mm ft–in m Box SkidCB12 8–0 2.44 55.4 25.1 63 48
120/135º 1-1/4 x 1-1/4 31.8 x 31.810–0 3.05 55.0 24.9 50 48(Dull Finish)
Splayed Corner Bead (CB12)
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:39 PM Page 153
Bulln
ose
90˚
(CB
B)
154 The place to stop…before the building starts! SMrequest a quote online @
Dietrich bullnose corner bead is used to create a smooth, rounded look tostandard drywall corners. Bullnose adds contemporary styling and a sense ofopenness to any room. Bullnose bead is nailed, screwed or stapled in placeand finished with joint compound.
Bullnose is available with a galvanized finish meeting ASTM C 1047 standardor with a prime painted surface for shadow-free finishing.
Dietrich bullnose to 90˚ transition caps are available to provide a smoothtransition to baseboard or corner molding. They install quickly and easily andcan be used with metal, vinyl or paper-faced bullnose corner bead.
Creates elegant, rounded outsidedrywall corners.■ Electrogalvanized finish for superior compound adhesion.
■ Galvanized for corrosion protection and durability.
■ Rugged steel construction.
Bullnose
Gypsum board panels must be cut back 3/4" toaccommodate the bullnose radius and ensure a flush fit.
Packaging may vary be region.
DMF Size Weight/Carton PackagingProduct Radius Length lbs kg Pcs/ Cartons/Code Inches mm ft–in m Box Skid
7–0 2.13 52.8 24.0 58 408–0 2.44 52.0 23.6 50 40
CBB3/4 19
8–6 2.59 55.3 25.1 50 40(Bullnose 90º) 9–0 2.74 52.7 23.9 45 40
10–0 3.05 52.0 23.6 40 4010–6 3.20 54.6 24.8 40 40
Bullnose 90º Corner Bead (CBB)
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:39 PM Page 154
Metal Corner BeadsBullnose Splayed 135˚ (C
BBW
)
155For more information or to contact a sales representative, see page 3
Dietrich splayed or off-angle bullnose is used to create a smoothrounded look to 135 degree corners. Bullnose adds contemporarystyling and a sense of openness to any room. Bullnose bead isnailed, screwed or stapled in place and finished with jointcompound.
Splayed Bullnose is available with a galvanized finish conforming toASTM C 1047 or prime painted surface for shadow-free finishing.
Splayed or offset bullnose providesrounded 135˚ outside corners for acontemporary, “modern” look.■ Rugged steel construction.
■ Galvanized coating for corrosion protection and durability.
■ Knurled flanges and hole pattern allow for superior compound adhesion. Splayed
Bullnose
Gypsum board panels must be cut back 3/4" toaccommodate the bullnose radius and ensure a flush fit.
Packaging may vary be region.
DMF Size Weight/Carton PackagingProduct Radius Length lbs kg Pcs/ Cartons/Code Inches mm ft–in m Box Skid
8–0 2.44 52.0 23.6 50 20
CBBW8–6 2.59 55.3 25.1 50 20
(Bullnose 135º)3/4 19 9–0 2.74 52.7 23.9 45 20
10–0 3.05 52.0 23.6 40 2010–6 3.20 54.6 24.8 40 20
Bullnose Splayed 135˚ Corner Bead (CBBW)
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:40 PM Page 155
Bulln
ose
Kerfe
d Be
ad (
CB
BK)
156 The place to stop…before the building starts! SMrequest a quote online @
Dietrich kerfed bullnose has a distinctive shortened back flangeallowing for insertion into grooved door jambs and window trims.This feature provides for efficient, clean installation, as well as thesmooth round appearance associated with bullnose trims. It is roll-formed from galvanized steel conforming to ASTM A 1047 for protection from corrosion and added durability.
Creates a rounded, paintable finisharound door jambs and window trims.■ Durable steel construction.
■ Galvanized coating for corrosion protection.
■ Cost-effective alternative to expensive wood trims.
Kerfed Bullnose
Packaging may vary by region.
DMF Size Weight/Carton PackagingProduct Radius Length lbs kg Pcs/ Cartons/Code Inches mm ft–in m Box Skid
7–0 2.13 49.0 22.2 58 20
3/4 198–0 2.44 48.0 21.7 50 209–0 2.74 49.0 22.2 45 20
CBBK 10–0 3.05 48.0 21.7 40 20(Bullnose Kerf) 7–0 2.13 24.0 10.9 29 40
1-1/2 388–0 2.44 24.0 10.9 25 409–0 2.74 25.0 11.3 23 4010–0 3.05 24.0 10.9 20 40
Bullnose Kerfed (CBBK)
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:40 PM Page 156
Metal Corner Beads“J” Round
™Bullnose (JRN
D)
157For more information or to contact a sales representative, see page 3
Dietrich “J” Round™ corner bead provides a rounded or bullnose edge at drywallterminations at doors and windows. “J” Round™ corner bead is available in 1/2" and5/8" sizes and in either a galvanized or prime painted surface for shadow-freefinishing. Coating finish must be specified at time of order.
Used to create a rounded or bullnose edge at drywall terminations at doors and windows.■ Strong metal reinforcement at doors and windows.
■ Requires less finishing compound.
■ Easy to install.
“J” Round™
DMF Size Weight/Carton PackagingProduct Radius Length lbs kg Pcs/ Cartons/ Code Inches mm ft–in m Box SkidJRND 8–0 2.44 16.00 7.24 25 20
(Bullnose 3/4 1910–0 3.05 16.00 7.24 20 20“J” Round™)
“J” Round™ Bullnose Corner Bead (JRND)
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:40 PM Page 157
2-W
ay M
etal
Cor
ner
Cap
90˚
(M
BC2)
& 3
-Way
Met
al C
orne
r C
ap 9
0˚ (
MBC
3)
158 The place to stop…before the building starts! SMrequest a quote online @
Easily joins bullnose corner beadat two-way intersections.■ Time-saver by avoiding costly mitering of corners.
■ Easy to install.
■ Corrosion-resistant and durable.
DMF Size Weight/Carton PackagingProduct Radius Style lbs kg Pcs/Box Boxes/SkidCode Inches mmMBC2 3/4 19 2-Way Metal Corner Cap 2.00 0.90 100 25
2-Way Metal Corner Cap 90˚ (MBC2)
DMF Size Weight/Carton PackagingProduct Radius Style lbs kg Pcs/Box Boxes/SkidCode Inches mmMBC3 3/4 19 3-Way Metal Corner Cap 2.00 0.90 75 25
3-Way Metal Corner Cap 90˚ (MBC3)
Dietrich Metal Framing 3-waymetal corner caps are quick andefficient solutions to finishing 3/4"bullnose systems at threeintersecting 90˚ corners. Stampedfrom corrosive-resistant steel, thissturdy cap solves many potentialfinishing problems associated withsoffit terminations, bank railpartitions and fireplaces.
Dietrich Metal Framing 2-waymetal corner caps aredesigned to finish 3/4"bullnose at 90˚ inside cornerintersections. Examples ofapplication include windows,closets, doorways, skylights,etc. This product is easy toinstall and provides a cost-effective alternative to time-consuming mitering ofcorners.
2-Way Metal Corner Cap
Cost-effective termination of three-way bullnose intersection.■ Eliminates need for special corner bead applications.
■ Provides superior corner finish with little effort.
■ Wide flanges aid bullnose corner alignment.
3-Way Metal Corner Cap
OvernightDelivery!
Available for
OvernightDelivery!
Available for
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:40 PM Page 158
Bullnose Corner and Transition CapsBullnose to 90˚ Transition C
ap (M859)
159For more information or to contact a sales representative, see page 3
Provides a transition for bullnose corners to baseboard or crown molding.
DMF Size Weight/Carton PackagingProduct Radius Style lbs kg Pcs/Box Boxes/SkidCode Inches mmM859 3/4 19 Bullnose to 90˚ Transition 4.00 1.80 100 25
Bullnose to 90˚ Transition Cap (M859)
Bullnose to 90˚ Transition Cap
Dietrich bullnose corners to 90˚ transition caps simplify installation of baseboard orcrown molding corners into 3/4" bullnose systems. Quick and easy to install, thisproduct eliminates corner gaps and the need for time-consuming caulking and filling.Can be used with metal or vinyl 3/4" bullnose corner bead for transition on baseboardor crown molding up to 4-1/2" in width.
■ Prevents gaps between bullnose corner bead and baseboard orcrown molding.
■ Eliminates need for time-consuming caulking and filling.
■ Used with baseboard or crown molding up to 4-1/2” in width.
■ Can be used with metal or vinyl bullnose corner beads.
Step 1 Step 2
Step 3 Step 4
OvernightDelivery!
Available for
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:40 PM Page 159
Clin
ch-O
n Pr
oduc
ts, C
o. C
orne
r Be
ad/E
lect
ro (
CBC
O)
Premier drywall finishing bead.■ Clinch-On Products, Co. provides premium,
high-quality finishing beads and trims.
■ Sturdy metal reinforcement for 90˚ drywall corners.
■ Electrogalvanized coating offers effective compound adhesion.
■ Nailed or clinched to framing and drywall.
Clinch-On Products, Co.ElectrogalvanizedCorner Bead
160 The place to stop…before the building starts! SMrequest a quote online @
Electrogalvanized corner bead provided by Clinch-OnProducts, Co. is recognized as the premier product forproviding sturdy metal reinforcement on 90˚ drywallcorners. Knurled and perforated flanges, along with theelectrogalvanized coating, offer superior compoundadhesion for smooth, straight finishes. Corner beadattachments are accomplished by nailing, stapling, screwingor clinching through the flanges.
Clinch-OnProducts, Co.’sCornerbead ToolFaster...Tighter...More Exact!Available by the piece or pallet.
Not available in all geographical areas.
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/Carton Carton/SkidCode Inches mm ft–in m
6–0 1.83 40.5 18.4 75 486–9 2.06 45.6 20.7 75 48
CBCO6–10 2.08 46.1 20.9 75 48
Electro 1-1/4 x 1-1/4 31.8 x 31.87–0 2.13 46.4 21.0 72 48
(Dull Gray)8–0 2.44 45.4 20.6 63 489–0 2.74 47.0 21.3 56 4810–0 3.05 45.0 20.4 50 4812–0 3.66 54.0 24.5 50 48
Clinch-On Products, Co. Corner Bead/Electro (CBCO)
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:40 PM Page 160
Corner Beads Provided by Clinch-On Products, Co.
Hot-dipped corner bead provided by Clinch-On Products, Co.offers the identical roll-formed precision as its electrogalvanizedcounterpart. Hot-dipped galvanized metal corner bead providesenhanced corrosion protection and sturdy reinforcement atexposed 90˚ corners. Flanges are knurled and perforated toease joint compound adhesion and nail attachment. Hot-dippedgalvanized metal meets ASTM A 1047.
Hot-dipped steel reinforcement for long-lasting,corrosion-resistant drywall corner protection.■ Clinch-On Products, Co. provides premium,
high-quality finishing beads and trims.
■ Sturdy metal reinforcement for 90˚ drywall corners.
■ Hot-dipped galvanized for corrosion protection.
■ Knurled and perforated flanges ease compound keying and nail attachment.
Clinch-On Products, Co.Hot-Dipped Corner Bead
Not available in all geographical areas.
Clinch-O
n Products, Co. C
orner Bead/Hot-D
ipped (CBC
S)
161For more information or to contact a sales representative, see page 3
Clinch-OnProducts, Co.’sCornerbead ToolFaster...Tighter...More Exact!Available by the piece or pallet.
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/Carton Carton/SkidCode Inches mm ft–in m
6–9 2.06 45.6 20.7 75 48
CBCS7–0 2.13 46.4 21.0 75 48
Hot-Dipped 1-1/4 x 1-1/4 31.8 x 31.88–0 2.44 45.4 20.6 63 48
(Shiny)9–0 2.74 47.0 21.3 56 4810–0 3.05 45.0 20.4 50 4812–0 3.66 54.0 24.5 50 48
Clinch-On Products, Co. Corner Bead/Hot-Dipped (CBCS)
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:40 PM Page 161
Clin
ch-O
n Pr
oduc
ts, C
o. C
orne
r Be
ad/S
moo
th (
CBC
P)
Smooth bead provided by Clinch-On Products, Co. is a nonknurledelectrogalvanized corner bead designed to use less joint compound.Roll-formed under the same quality standards as all of their products,this corner bead provides lasting corner protection to exposeddrywall edges and smooth, straight corners. Nailing perforations andelectrogalvanized coating offer effective joint compound adhesion.This product is commonly used in selected southeastern areas.
162 The place to stop…before the building starts! SMrequest a quote online @
Clinch-OnProducts, Co.ElectrogalvanizedCorner Bead
Compound-reducing steel reinforcementfor lasting drywall corner protection.■ Nonknurled, uses less joint compound.
■ Electrogalvanized coating offers effective compound adhesion.
■ Nailed or clinched to framing and drywall.
Not available in all geographical areas.
Clinch-OnProducts, Co.’sCornerbead ToolFaster...Tighter...More Exact!Available by the piece or pallet.
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/Carton Carton/SkidCode Inches mm ft–in m
6–9 2.06 45.6 20.7 75 487–0 2.13 46.4 21.0 75 48
CBCP1-1/4 x 1-1/4 31.8 x 31.8
8–0 2.44 45.4 20.6 63 48Smooth 9–0 2.74 47.0 21.3 56 48
10–0 3.05 45.0 20.4 50 4812–0 3.66 54.0 24.5 50 48
Clinch-On Products, Co. Electrogalvanized Corner Bead/Smooth (CBCP)
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:40 PM Page 162
Corner Beads Provided by Clinch-On Products, Co.
Clinch-On Products, Co. splayed corner bead is a roll-formedmetal angle used to establish smooth, straight corners at baywindows, stairwell ceilings and similar conditions wheredrywall intersects at angles of 120˚ or more. Knurled andperforated flanges provide strong adhesion of compoundand the exposed nose forms a screed for finishing. Hot-dipped galvanized meets ASTM A 653. This product is alsoavailable with an electrogalvanized coating (CBSE) in certainregions.
Provides strong durable protection for off-angledor splayed corners from 120˚–135˚.■ Clinch-On Products, Co. provides premium,
high-quality finishing beads and trims.
■ Sturdy metal reinforcement for off-angled drywall corners.
■ Hot-dipped galvanized for corrosion protection.
■ Knurled and perforated flanges ease keying of compound.
Clinch-O
n Products, Co. Splayed C
orner Bead Hot-D
ipped (CBC
W)
163For more information or to contact a sales representative, see page 3
Clinch-On Products, Co.Splayed Corner Bead
Not available in all geographical areas.
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/Carton Carton/SkidCode Inches mm ft–in mCBCW 8–0 2.44 45.4 20.6 40 48
120/135˚ 1-1/4 x 1-1/4 31.8 x 31.8 9–0 2.74 47.0 21.3 40 48(splayed) 10–0 3.05 45.0 20.4 40 48
Clinch-On Products, Co. Splayed Corner Bead/Hot-Dipped (CBCW)
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:40 PM Page 163
Clin
ch-O
n Pr
oduc
ts, C
o. H
ot-D
ippe
d Bu
llnos
e (C
BBC
)
164 The place to stop…before the building starts! SMrequest a quote online @
Creates elegant rounded outside drywall corners.■ Clinch-On Products, Co. provides premium,
high-quality finishing beads and trims.
■ Sturdy metal reinforcement for smooth, rounded drywall corners.
■ Hot-dipped galvanized coating resists corrosion.
■ Generous 3/4” flange enables nail, screw or adhesive application.
Clinch-OnProducts, Co. Hot-DippedBullnose
Hot-dipped bullnose corner bead provided by Clinch-On Products, Co. isused to create a smooth, rounded look to standard drywall corners. Bullnoseadds contemporary styling and a sense of openness to any room. The hot-dipped finish provides superior corrosion resistance.
Gypsum board panels must be cut back 3/4" to accommodate the bullnoseradius and ensure a flush fit. Bullnose bead is nailed, screwed or stapled inplace and finished with joint compound.
Bullnose to 90˚ Transition Caps are available to provide a smooth transitionto baseboard or crown molding. They install quickly and easily and can beused with metal, vinyl or paper-faced bullnose corner bead.
Not available in all geographical areas.
DMF Size Weight/Carton PackagingProduct Radius Length lbs kg Pcs/Carton Carton/SkidCode Inches mm ft–in m
6–0 1.83 26.4 12.0 40 326–9 2.06 29.7 13.5 40 32
CBBC6–10 2.08 30.1 13.7 40 32
Hot-Dipped 3/4 197–0 2.13 30.8 14.0 40 32
(shiny)8–0 2.44 35.2 16.0 40 329–0 2.74 39.6 18.0 40 3210–0 3.05 44.0 20.0 40 3212–0 3.66 52.8 23.9 40 32
Clinch-On Products, Co. Hot-Dipped Bullnose (CBBC)
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:40 PM Page 164
Corner Beads Provided By Clinch-On Products, Co.C
linch-On Products, C
o. Painted 3/4" Bullnose Splayed (CB
PS)
165For more information or to contact a sales representative, see page 3
Painted 3/4" splayed bullnose provided by Clinch-On Products,Co. is used to create a smooth, rounded look to 120–135˚corners. The prime painted surface provides a ready-to-paintshadow-free finish.
Bullnose bead is nailed, screwed or stapled in place andfinished with joint compound.
Strong steel reinforcement for lastingcorner protection.■ Clinch-On Products, Co. provides premium,
high-quality finishing beads and trims.
■ Prime painted surface provides shadow-free finish.
■ Underlying galvanized coating resists corrosion.
■ Excellent compound adhesion.Clinch-On Products, Co.Painted Splayed Bullnose
Not available in all geographical areas.
Gypsum board panels must be cut back 3/4" to accommodatethe bullnose radius and ensure a flush fit.
DMF Size Weight/Carton PackagingProduct Radius Length lbs kg Pcs/Carton Carton/SkidCode Inches mm ft–in m
6–9 2.06 29.7 13.5 40 327–0 2.13 30.8 14.0 40 32
CBPS3/4 19
8–0 2.44 35.2 16.0 40 32(painted) 9–0 2.74 39.6 18.0 40 32
10–0 3.05 44.0 20.0 40 3212–0 3.66 52.8 23.9 40 32
Clinch-On Products, Co. Painted 3/4" Splayed Bullnose (CBPS)
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:40 PM Page 165
Clin
ch-O
n Pr
oduc
ts, C
o. H
ot-D
ippe
d 3/
4" B
ulln
ose
Spla
yed
(CB
SB)
Hot-dipped 3/4" bullnose splayed provided by Clinch-OnProducts, Co. is a sturdy metal component used to create asmooth, round transition at exposed open angledintersections exceeding 120˚. A generous 3/4" flangeallows for nail, screw or adhesive attachments. Knurled andperforated flanges provide effective joint compoundadhesion. The hot-dipped coating provides addedcorrosion resistance and is commonly used in humidregions. Splayed bullnose is also available withelectrogalvanized coating (CBBW ).
Strong steel reinforcement for lasting corner protection■ Clinch-On Products, Co. provides premium,
high-quality finishing beads and trims.
■ Sturdy, rounded wall transition at open angled corners.
■ Hot-dipped galvanized coating resists corrosion.
■ Generous 3/4” flange allows for nail, screw or adhesive attachment.
166 The place to stop…before the building starts! SMrequest a quote online @
Clinch-OnProducts, Co.Hot-DippedSplayedBullnose
Gypsum board panels must be cut back 3/4" toaccommodate the bullnose radius and ensure a flush fit.
Not available in all geographical areas.
DMF Size Weight/Carton PackagingProduct Radius Length lbs kg Pcs/Carton Carton/SkidCode Inches mm ft–in m
6–9 2.06 29.7 13.5 40 32
CBSB7–0 2.13 30.8 14.0 40 32
Hot-Dipped 3/4 198–0 2.44 35.2 16.0 40 32
(Shiny)9–0 2.74 39.6 18.0 40 3210–0 3.05 44.0 20.0 40 3212–0 3.66 52.8 23.9 40 32
Clinch-On Products, Co. Hot-Dipped Bullnose Splayed (CBSB)
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:40 PM Page 166
Corner Beads Provided by Clinch-On Products, Co.
Painted 3/4" bullnose corner bead provided by Clinch-OnProducts, Co. is used to create a smooth, rounded look tostandard drywall corners. Bullnose adds contemporary stylingand a sense of openness to any room. The prime paintedsurface provides a ready-to-paint shadow-free finish. Bullnosebead is nailed, screwed or stapled in place and finished withjoint compound.
Bullnose to 90˚ Transition Caps are available to provide asmooth transition to baseboard or crown molding. Theyinstall quickly and easily and can be used with metal, vinyl orpaper-faced bullnose corner bead.
Creates elegant, rounded, shadow-freeoutside drywall corners.■ Clinch-On Products, Co. provides premium,
high-quality finishing beads and trims.
■ Prime painted surface provides a shadow-free finish.
■ Underlying galvanized coating resists corrosion.
■ Excellent compound adhesion.
Clinch-O
n Products, Co. Painted 3/4" Bullnose (C
BPB)
167For more information or to contact a sales representative, see page 3
Clinch-OnProducts, Co.Painted Bullnose
Gypsum board panels must be cut back 3/4" toaccommodate the bullnose radius and ensure a flush fit.
Not available in all geographical areas.
DMF Size Weight/Carton PackagingProduct Radius Length lbs kg Pcs/Carton Carton/SkidCode Inches mm ft –in m
6–9 2.06 29.7 13.5 40 327–0 2.13 30.8 14.0 40 32
CBPB3/4 19
8–0 2.44 35.2 16.0 40 32(painted) 9–0 2.74 39.6 18.0 40 32
10–0 3.05 44.0 20.0 40 3212–0 3.66 52.8 23.9 40 32
Clinch-On Products, Co. Painted 3/4" Bullnose (CBPB)
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:40 PM Page 167
168 The place to stop…before the building starts! SMrequest a quote online @
Met
al J
-Trim
(M
400
Serie
s™)
Dietrich metal J-Trims are strong, reveal-type galvanizedsteel casings that provide maximum protection and neatfinished edges to drywall terminations around door andwindow openings. Metal J-Trims also deliver a clean trimline at intersections or where gypsum panels abutdissimilar surfaces such as columns and window mullions.Hemmed-edges allow for quick installation and do notrequire joint compound for finishing.
Used as a finished edge for wallboard at doorand window openings or when gypsum panels meet dissimilar surfaces.■ Requires no joint compound.
■ Galvanized for corrosion protection.
■ Hemmed edges for quick installation.
J-Trim
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Cartons/Code Inches mm ft–in m Carton Skid
M400 3/8 9.58–0 2.44 36.0 16.3 50 5010–0 3.05 45.0 20.4 50 50
M401 1/2 12.78–0 2.44 36.0 16.3 50 5010–0 3.05 45.0 20.4 50 50
M402 5/8 15.98–0 2.44 36.0 16.3 50 5010–0 3.05 45.0 20.4 50 50
Metal J-Trim (M400 Series™)
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:40 PM Page 168
169For more information or to contact a sales representative, see page 3
Metal Trims and Finishing Products
Dietrich U-Trim, or Spackle J is used to provide maximumprotection and clean finished edges on gypsum panels arounddoor and window openings and when wallboard abutsdissimilar surfaces, such as suspended ceilings, beams, plaster,masonry and concrete. U-Trim is easily installed by sliding trimover the edge of the board and nailing or screwing through theknurled (long) flange. Installation is completed with applicationof joint compound for a smooth ready-to-paint surface.
Used in conjunction with joint compound when a clean,finished edge is required at door and window openings or when dissimilar materials meet.■ Rugged steel construction.
■ Galvanized for corrosion protection.
■ Knurled, perforated flange enhances compound adhesion.
Metal U
-Trim/Spackle J (M
20A)
U-Trim/Spackle J
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Cartons/Code Inches mm ft–in m Carton Skid
1/2 12.78–0 2.44 36.0 16.3 50 50
M20A10–0 3.05 45.0 20.4 50 50
5/8 15.98–0 2.44 36.0 16.3 50 5010–0 3.05 45.0 20.4 50 50
Metal U-Trim/Spackle J (M20A)
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:41 PM Page 169
Met
al L
-Trim
(M
20B)
Dietrich metal L-Trim is used to provide a clean finishededge at door and window openings or when wallboardabuts dissimilar surfaces such as suspended ceilings,beams, plaster, masonry and concrete. L-Trim is installedafter the gypsum panels are already in place, unlike Spackle J, which must be installed during gypsum panelinstallation. L-Trim is easily attached with screws or nailsafter the panels are in place. Installation is completed withjoint compound for a smooth ready-to-paint surface.
Provides a clean finished edge for wallboard and can beinstalled after gypsum panel installation.■ Hemmed front flange for rigidity.
■ Knurled, perforated flange enhances joint compound adhesion.
■ Easy to attach and finish.
170 The place to stop…before the building starts! SMrequest a quote online @
L-Trim
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Cartons/Code Inches mm ft–in m Carton Skid
1/2 12.78–0 2.44 28.0 12.7 50 50
M20B10–0 3.05 35.0 15.9 50 50
5/8 15.98–0 2.44 28.0 12.7 50 5010–0 3.05 35.0 15.9 50 50
Metal L-Trim (M20B)
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:41 PM Page 170
Metal Trims and Finishing Products
Dietrich 093 Zinc Control Joint is applied between abuttinggypsum panels, and is used to relieve stresses of expansionand contraction of drywall and veneer plaster systems inlarge ceiling and wall expanses over 30' in length. 093 ZincControl Joint is typically installed from door header toceiling, from floor to ceiling in long partition runs, and fromwall to wall in large ceiling areas. Zinc Control Joints aremanufactured from high-quality pure zinc and can be usedfor interior or exterior applications. The 1/4" by 7/16"opening is protected by plastic tape, which is removed afterjoint compound or plaster has been applied and the finish iscompleted.
Note: Where fire and sound control are primeconsiderations, an approved seal must be installedbehind the control joint.
Relieves stresses of expansion and contraction across large ceilingand wall areas.■ Relieves stresses of expansion and contraction.
■ Superior corrosion resistance.
■ Easy to apply and finish.
■ Use with drywall or veneer plaster.
093 Zinc Control Joint (ZN
CJ)
171For more information or to contact a sales representative, see page 3
093 Zinc Control Joint
DMF Size Weight/Carton PackagingProduct Grounds Length lbs kg Pcs/ Cartons/Code Inches mm ft–in m Carton SkidZNCJ 3/32 2.4 10–0 3.05 22.5 10.2 25 64
093 Zinc Control Joint (ZNCJ)
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:41 PM Page 171
Min
i-Bea
d™80
0 (M
B80/
ZB80
) an
d M
ini-B
ead™
900
(MB9
0/ZB
90)
172 The place to stop…before the building starts! SMrequest a quote online @
High-quality veneer finishing corner beadprovides superior keying for jointcompound for one-coat plaster veneer systems.■ Mini-mesh flanges for plaster keying.
■ Galvanized or zinc for corrosion protection.
■ Universally accepted as Kal-Korner™ alternative.
■ Eliminates shadowing and edge cracking.
Mini-Bead™
Dietrich Mini-Bead™ 800 and 900 corner bead are galvanized steelreinforcements for interior, outside corner, veneer or thin wallplaster applications. 1-1/4" wide fine mesh expanded flanges aretapered along the outer edges to enhance veneer plasterconcealment. Mini-Bead™ 800 corner bead has 1/16" grounds forone-coat veneer plaster and 90 keys per linear foot for excellentbonding and strong corners. Mini-Bead™ 900 corner bead has3/32" grounds for two-coat veneer plaster systems. Zinc Mini-Bead™ 900 should be used in exterior finish systems. Flangeattachments can be accomplished by either nailing or stapling.
Note: Zinc Mini-Bead™ corner bead should be used inexterior finish systems.
*Kal-Korner™ Bead is a registered trademark of National Gypsum Company.**Zinc.
DMF Size Weight/Carton PackagingProduct Ground Width Length lbs kg Pcs/Carton Cartons/SkidCode Inches mm Inches mm ft–in m
MB80 1/16 1.6 1-1/4 x 1-1/4 31.8 x 31.88–0 2.44 33.6 15.2
60 2510–0 3.05 42.0 19.0
MB90 3/32 2.4 1-1/4 x 1-1/4 31.8 x 31.88–0 2.44 33.6 15.2
60 2510–0 3.05 42.0 19.0
ZB80** 1/16 1.6 1-1/4 x 1-1/4 31.8 x 31.8 10–0 3.05 36.0 16.360 25
ZB90** 3/32 2.4 1-1/4 x 1-1/4 31.8 x 31.8 10–0 3.05 36.0 16.3
Mini-Bead™ 800 (MB80/ZB80) and 900 (MB90/ZB90)
149-172 Metal Beads and Trims:DMF07_133 7/6/10 4:41 PM Page 172
173
Vinyl Corner BeadsVinyl Corner Bead (VLCB)................176Vinyl #1 Corner with 2-1/2" Legs(VC1A) ....................................................176Vinyl Splayed Corner Bead 120/135˚(VLSB) ....................................................177Vinyl Archway Corner Bead (VLAB) ..177Vinyl Bullnose (VBCB) ......................178Vinyl Bullnose Splayed (VBSB)......178Vinyl Bullnose Kerfed (VBKB) ........179Vinyl Bullnose Archway (VBAB) ....179Bullnose Corner and Transition Caps2-Way Inside 3/4" Bullnose CornerCap 90˚ (M285) ................................1803-Way 3/4" Bullnose Corner Cap 90˚(M385) ..................................................1803-Way Overlap 3/4" Bullnose CornerCap 90˚ (M384) ................................1813-Way Overlap 1-1/2 Bullnose CornerCap 90˚ (M387)..................................1813-Way Off-Angle Overlap 3/4"Bullnose Corner Cap (M134) ........1821-1/2" Bullnose Corner Caps (M187) ..................................................182Bullnose to 90˚ Transition Cap (M859) ..................................................183Vinyl Trims and Finishing ProductsVinyl J-Bead (VLJB) ............................184Vinyl Mudable J-Bead (VLMJ) ........184Vinyl L-Stop Bead (VLLS) ................185Vinyl Rip Bead™ L-Trim (VLZL) ........185Vinyl Partition End Cap 1/2" (PC50)or 5/8 " (PC58)..................................186Vinyl 093 Drywall Control Joint (VCJT)......................................................186
Vynyl Beads & Trim 173_186:DMF07_149 7/15/10 3:16 PM Page 179
Viny
l Bea
ds &
Trim
s O
verv
iew
174 The place to stop…before the building starts! SMrequest a quote online @
VINYL BEADS& TRIMS
OVERVIEWVinyl beads and trims are designedto provide superior, long-lasting inte-rior finishes for drywall and veneerplaster. These beads and trims areused to provide durable, corrosion-and impact-resistant edges, corners,arches, curvatures and numerousother finishing applications. Vinylbeads and trims continue to grow inpopularity because they give archi-tects, interior designers and contrac-tors much more flexibility to createdramatic, sweeping arches, curva-tures and distinctive architecturaldetails.
Advantages
Durability—Vinyl accessories are impervious to corrosion when coated with veneerplaster, wet joint compounds or when placed in contact with steel or aluminum frames.Vinyl accessories do not contain plasticizers that could migrate to the surface.
Impact Resistance—Due to superior impact resistance, rigid vinyl accessories areresistant to dents and kinks of corners and edges, during and after construction.
Corrosion Resistance—Vinyl accessories are impervious to rust, corrosion, galvaniccorrosion, electrolysis, and are not affected by fast-setting joint compounds or toppingcompounds.
Solid Color—Standard color is white for a shadow-free finish.
Paint Adhesion Properties—Excellent, no priming is required.
Ignition Resistance—Rigid vinyl is self-extinguishing, and will not continue to sup-port combustion once flame source is removed; therefore, it will not cause a fire to re-start or spread. It offers better resistance to burning than many other common building materials.
Expansion and Contraction—Vinyl accessories are manufactured with perforationsin the flanges to enable finishing compounds or veneer plaster to flow through andbond to wallboard. Perforated flanges remain embedded in matrix to reinforce theedges and corners. These factors, along with the fastening of accessories to the sub-strate prior to coating, make the accessories part of the building unit and therefore willmove with it as the temperature changes, consequently the coefficient of expansion ofrigid vinyl has little or no bearing on the installation.
Vynyl Beads & Trim 173_186:DMF07_149 7/15/10 3:16 PM Page 180
OverviewVinyl Beads & Trim
s Overview
175For more information or to contact a sales representative, see page 3
Styles & Types
Vinyl Corner Bead is arigid, easy-to-apply cor-ner reinforcement thatmay be nail or stapleapplied. Flanges are 1-1/4" wide and are per-forated to aid joint com-pound bond. Rigid vinylresists dents, thermaltransmission and willnot corrode.
Vinyl Splayed Bullnose Corner Bead fits off-angle cor-ners that typically are 120˚–135˚.
1-1/4" Archway Corner Bead has the same properties asregular 1-1/4" vinyl corner bead, plus it’s manufactured withnotched tabs on one flange to permit flexible forming ofarchway edges. Available in 8' and 10' lengths.
All Dietrich vinyl products readily accept finish treatmentssuch as paint and spray or roll-on textures.
90˚ Bullnose Corner Bead comes in a choice of 3/4" ormore dramatic 1-1/2" radius to make rounded, more con-temporary corners. Fits 90˚ corners.
Vinyl 90˚ Bullnose Archway Corner Bead provides abullnose treatment around arched openings. Tabs enablebead to be arched to a 10" inside radius or 18" outsideradius.
3/4" Vinyl Bullnose Kerfed is the same as regular 3/4"radius bead, except it is kerfed so that the leg fits the chan-nel of door and window jambs for smooth, roundedencasement.
Vinyl J-Trim provides a finished edge at gypsum boardstops around door and window openings and at ceilingintersections. Requires no joint compound. Rigid vinyl is nota thermal transmitter and helps stop condensation whereboard terminates at exterior metal surfaces, such as windowframes and mullions. It’s rustproof and dent resistant.
Rip Bead™ vinyl beadsproduce an exceptionalfinish at the intersectionof gypsum board andceiling grid. Once jointcompound is applied,the tear-away strip isremoved, producing acrisp, clean edge.
Vinyl L-Stop Bead is aconvenient finished ter-
mination for gypsum panel surfaces. Bead may be nail or sta-ple attached to the stud through the bead flange. The flangeis 1-1/4" wide and is perforated to aid joint compound bond.Rigid vinyl is rust proof and dent resistant. Surface is treatedwith an alkyd texture to help joint compound and paintadhere.
OVER 850+ Vinyl Products
The products in this section are limited to common drywall and veneer plaster finishing accessories.An extensive array of vinyl products is available through our vinyl specialty company, Vinyl Corp.™
Vinyl Corp.™ is one of the largest full-line vinyl bead and trim manufacturers in the U.S. Productcategories include vinyl beads, trims and control joints for Stucco/Plaster, Drywall, ExteriorInsulation Finish Systems (E.I.F.S.), and Direct-applied Exterior Finish Systems (D.E.F.S.).
Vinyl Corp.™ is committed to meeting the most complex challenges in the wall and ceiling indus-try through innovative product design, exacting manufacturing tolerances and the most completeselection of accessories in the industry. Contact one of Vinyl Corp.™’s customer care representa-tives at 800-648-4695.
Vynyl Beads & Trim 173_186:DMF07_149 7/15/10 3:16 PM Page 181
Viny
l Cor
ner
Bead
(VL
CB)
& V
inyl
#1
Cor
ner
with
2-1
/2"
Legs
(VC
1A)
176 The place to stop…before the building starts! SMrequest a quote online @
Dietrich vinylcorner bead is a rigid, easy-to-apply 90˚ cornerreinforcementthat can be nailedor stapled intoplace. Multipleperforationsalong the 1-1/4"flanges enhancejoint compound
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Cartons/Code Inches mm ft m Carton Skid
VLCB 1-1/4 x 1-1/4 31.8 x 31.88 2.44 24.0 10.9 50 3510 3.05 30.0 13.6 50 35
Vinyl Corner Bead (VLCB)
Rust-proof, impact-resistant vinyl corner reinforcement.■ Rust proof and dent resistant.
■ Multiple perforations enhance joint compound bond.
■ Maintains shape with no sharp edges or burrs when field cut.
■ Easily cut with snips, utility knives or scissors.
bonding. The pronounced nose provides a ground andscreed to help the finisher achieve precise finishing depth.Rigid vinyl is dent resistant, rust proof and maintains shapewith no sharp edges or burrs when field cut. All Dietrichvinyl products readily accept finish treatments such as paintand spray or roll-on textures.
Dietrich Vinyl #1Corner providesstraight, true, rust-proofreinforcement for90˚ corners inhigh-traffic andhigh-abuse areaswhere extra cornerprotection isdesired. Ideal forfinishing double
Great for high-traffic and high-abuse corners.■ Rust proof and dent resistant.
■ Quick and easy to install.
■ Sturdy reinforcement for exterior stucco corners.
layers of 5/8" gypsum. The pronounced nose of this beadserves as a screed to aid the applicator in achieving the desiredfinish depth. Stiffener ribs and nail perforations contribute toquick and easy installation that is straight and level.
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Cartons/Code Inches mm ft m Carton Skid
VC1A 2-1/2 x 2-1/2 63.5 x 63.58 2.44 40.0 18.1 50 2510 3.05 50.0 22.7 50 25
Vinyl #1 Corner with 2-1/2" Legs (VC1A)
Vinyl Corner Bead
2-1/2" Leg VinylCorner Bead
Vynyl Beads & Trim 173_186:DMF07_149 7/15/10 3:17 PM Page 182
Vinyl Corner BeadsVinyl Splayed C
orner Bead 120/135˚ (VLSB) & Vinyl Archway C
orner Bead (VLAB)
177For more information or to contact a sales representative, see page 3
Dietrich 120/135˚ corner or splayed bead is used to finish off angle interior cornersfrom 120–135˚. Designed to provide straight, rust-proof, dent-resistant corners, theflexibility of vinyl splay bead allows a flush fit on many unusual outside wallboardintersections. Multiple perforations along the 1-1/4" flanges enhance joint compoundbonding. Easy to apply, this vinyl trim can be nailed, stapled or attached with a high-tack spray adhesive. Vinyl beads are easily cut with snips, utility knife or scissorswithout distorting the profile.
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Cartons/Code Inches mm ft m Carton Skid
VLSB 1-1/4 x 1-1/4 31.8 x 31.88 2.44 24.0 10.9 50 3510 3.05 30.0 13.6 50 35
Vinyl Splayed Corner Bead 120/135˚ (VLSB)
Versatile, rigid corner reinforcement for off-angled wallboard intersections.■ Rust proof and dent resistant.
■ Multiple perforations enhance joint compound bond.
■ Flexibility allows flush fit on unusual outside corner angles.
Dietrich vinyl archwaycorner bead form fitsalmost any arch, curve or radius to provide rigid corner and edgeprotection. The notchedsingle flange adapts tovirtually any radiuscondition. Multipleperforations along flanges
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Cartons/Code Inches mm ft m Carton Skid
VLAB 1-1/4 x 1-1/4 31.8 x 31.88 2.44 20.0 9.1 50 3510 3.05 25.0 11.3 50 35
Vinyl Archway Corner Bead (VLAB)
Used to finish arches, curvatures and most radius conditions.■ Ideal for archways, curves and radius windows.
■ Maximum flexibility.
■ Rust proof and dent resistant.
■ Multiple perforations enhance joint compound bond.
■ Notched flange adapts to virtually any radius condition.
and notches enhance compound and veneer plaster bonding.In addition to nail or staple fastening, an adhesive should beused to secure arch tabs to gypsum board.
Splayed CornerBead
Archway Corner Bead
Vynyl Beads & Trim 173_186:DMF07_149 7/15/10 3:17 PM Page 183
Viny
l Bul
lnos
e (V
BCB)
& V
inyl
Bul
lnos
e Sp
laye
d (V
BSB
)
The place to stop…before the building starts! SMrequest a quote online @
Dietrich vinyl bullnose corner bead is usedto create a smooth, rounded look tostandard drywall corners. Vinyl bullnoseadds contemporary styling and a sense ofopenness to any room. Available in choiceof 3/4" or more dramatic 1-1/2" radius.Easily installed with nails, screws or staples,this sturdy vinyl product is rust-proof anddent-resistant.
DMF Size Weight/Carton PackagingProduct Radius Length lbs kg Pcs/ Cartons/Code Inches mm ft m Carton Skid
VBCB 3/4 198 2.44 25.20 11.43 35 35
90º10 3.05 31.50 14.29 35 35
Bullnose 1-1/2 388 2.44 31.20 14.15 30 3510 3.05 39.00 17.69 30 35
90˚ Vinyl Bullnose (VBCB)
Used to create elegant, contemporary, rounded 90˚ drywall corners.■ Rust proof and dent resistant.
■ Multiple perforations enhance joint compound bond.
■ Especially useful in children’s play areas.
Dietrich vinyl bullnosesplayed corner bead isused to finish off-angleinterior corners from120–135˚ when arounded “bullnose”look is desired.Bullnose bead providesan architecturally
attractive, contemporary and open feel to any room.
DMF Size Weight/Carton PackagingProduct Radius Length lbs kg Pcs/ Cartons/ Code Inches mm ft m Carton Skid
3/4 198 2.44 19.60 8.89 35 35
VBSB10 3.05 24.50 11.11 35 35
1-1/2 388 2.44 24.00 10.89 30 3510 3.05 30.00 13.61 30 35
120–135˚ Vinyl Bullnose Splayed (VBSB)
Creates contemporary splayed or off-angle rounded corners.■ Rust proof and dent resistant.
■ Multiple perforations enhance joint compound bond.
■ Flexibility allows snug fit on unusual outside corner angles.
This durable trim product is dent resistant, rust-proof andeasily finished. Multiple elongated perforations along bothflanges enhance joint compound bond. Available in 3/4"and 1-1/2" radius.
90˚ Bullnose Corner Bead
120–135˚SplayedBullnose
Gypsum panels must be cut back 3/4"to accommodate bullnose radius and
ensure a flush fit on the flanges.
178
Vynyl Beads & Trim 173_186:DMF07_149 7/15/10 3:17 PM Page 184
Vinyl Corner BeadsVinyl Bullnose Kerfed (VB
KB) & Vinyl Bullnose Archway (VBAB)
179For more information or to contact a sales representative, see page 3
Dietrich vinylbullnose kerfedcorner bead has adistinctive shortenedback flange, allowing
for insertion into grooved door jambs and window trims.This feature provides for efficient, clean installation as well asthe smooth, rounded appearance associated with bullnose
DMF Size Weight/Carton PackagingProduct Radius Length lbs kg Pcs/ Cartons/Code Inches mm ft m Carton Skid
3/4 198 2.44 11.2 5.1 50 35
VBKB10 3.05 14.0 6.4 50 35
1-1/2 388 2.44 12.0 5.4 50 3510 3.05 15.0 6.8 50 35
Vinyl Bullnose Kerfed (VBKB)
Creates a rounded or bullnose paintable finisharound door and window trims.
trims. Rigid vinyl is dent resistant, rust proof and maintainsshape with no sharp edges or burrs when field cut. A cost-effective alternative to expensive wood trims.
DMF Size Weight/Carton PackagingProduct Radius Length lbs kg Pcs/ Cartons/Code Inches mm ft m Carton Skid
3/4 198 2.44 14.0 6.4 35 35
VBAB10 3.05 17.5 7.9 35 35
1-1/2 388 2.44 16.8 7.6 30 3510 3.05 21.0 9.5 30 35
Vinyl Bullnose Archway (VBAB)
For finishing arches, curvatures and most radiiwith a rounded bullnose look.
■ Rust proof and dent resistant.
■ Easy to install.
■ Cost-effective alternative to expensive wood trims.
■ Ideal for archways,curves and dramaticarchitectural detailing.
■ Rust proof and dent resistant.
■ Multiple perforationsenhance jointcompound bond.
■ Maximum flexibility.
■ Notched flange adaptsto virtually any radiuscondition.
Dietrich vinyl bullnose archway corner bead is used toprovide a rounded, contemporary look to archways, curvesor just about any radius. Notched flanges enable this bead to be arched to an inside or outside radius.
Each tab on the archway bead should be secured withadhesive or staples before application of joint compound.Multiple perforations along the flanges enhance jointcompound bond. Available in 3/4" and 1-1/2" radius.
Bullnose Kerfed
BullnoseArchway
Vynyl Beads & Trim 173_186:DMF07_149 7/15/10 3:17 PM Page 185
2-W
ay In
side
3/4
" Bu
llnos
e C
orne
r C
ap 9
0˚ (
M28
5) &
3-W
ay 3
/4"
Bulln
ose
Cor
ner
Cap
90˚
(M
385)
Dietrich vinyl 2-way 3/4" cornercaps provide the ideal componentto transition bullnose corner beadsto a crisp finish where insidecorners intersect at 90˚. Examplesof applications include windows,closets, doorways, skylights, etc. Easy to install, this componentprovides a cost-effective alternative totime-consuming mitering of corners.
DMF Size Weight/Carton PackagingProduct Radius mm Style lbs kg Pcs/Box Boxes/SkidCodeM285 3/4 19.1 Plastic 2-Way Corner Cap 2.0 0.90 100 25
2-Way Inside 3/4" Bullnose Corner Cap 90˚ (M285)
For a professional finish where two bullnose corners meet at 90.̊■ Eliminates costly mitering of corners.
■ Easy to install.
■ Rust proof and dent resistant.
DMF Size Weight/Carton PackagingProduct Radius mm Style lbs kg Pcs/Box Boxes/SkidCodeM385 3/4 19.1 Plastic 3-Way Corner Cap 2.0 0.90 100 25
3-Way 3/4" Bullnose Corner Cap 90˚ (M385)
2-Way Inside 3/4" Bullnose C orner Cap 90˚
3-Way 3/4" Bullnose Corner Cap 90˚
For a professional finish where three3/4" bullnose corners meet at 90˚.■ No need for special corner bead applications.
■ Easy to install.
■ Huge labor saver.
■ Favorite of metal bullnose corner bead users.
Dietrich 3-way 3/4" bullnose 90˚ corner capsprovide the ideal solution to finish cornersquickly and efficiently at three-way 90˚ 3/4"bullnose intersections. This corner capfeatures extended tabs for easier alignmentand a professional finish, and it works wellwith both metal and vinyl bullnose cornerbeads.
M385 bullnose corner cap eliminates theneed for special corner bead applicationsand time-consuming mitering.
180 The place to stop…before the building starts! SMrequest a quote online @
OvernightDelivery!
Available for
OvernightDelivery!
Available for
Vynyl Beads & Trim 173_186:DMF07_149 7/15/10 3:17 PM Page 186
Bullnose Corner and Transition Caps
Dietrich 3-way 3/4" overlap cornercaps provide the ideal solution tofinish corners quickly and efficiently at three-way 90˚ bullnoseintersections. Easy to install, thisrust-proof and dent resistant vinylcap solves many potential finishingproblems.
DMF Size Weight/Carton PackagingProduct Radius mm Style lbs kg Pcs/Box Boxes/SkidCodeM384 3/4 19.1 Plastic 3-Way Overlap Corner Cap 2.0 0.90 50 25
3-Way Overlap 3/4" Bullnose Corner Cap 90˚ (M384)
Use to finish three-way bullnose 90˚ intersections. Added tabs for enhanced corner alignment.■ Substantially reduces labor.
■ No need for special corner bead applications.
■ Easy to install.
■ Works with metal and vinyl bullnose corner beads.
For a professional finish where three1-1/2" bullnose corners meet at 90˚.
Dietrich 3-way 1-1/2" 90˚ bullnose corner capprovides the ideal solution to finish cornersquickly and efficiently at three-way 90˚ 1-1/2" bullnose intersections. It’s especiallydesigned to deliver an ultra-soft cornerappearance associated with 1-1/2" bullnose corner bead.Eliminates the need for special corner bead applications and time-consuming mitering.Easy to install, extended tabs and flanges ensure proper corner alignment andprofessional finish.
DMF Size Weight/Carton PackagingProduct Radius mm Style lbs kg Pcs/Box Boxes/SkidCodeM387 1-1/2 38.1 Plastic 3-Way Corner Cap 1-1/2" 2.00 0.90 50 25
3-Way Overlap 1-1/2" Bullnose Corner Cap 90º (M387)
■ Creates a soft, rounded appearance.
■ No need for special corner bead applications.
■ Easy to install.
■ Huge labor savings.
■ Rust proof and dent resistant.
3-Way Overlap 3/4" BullnoseCorner Cap 90˚
3-Way Overlap1-1/2" BullnoseCorner Cap 90º
3-Way O
verlap 3/4" Bullnose Corner Cap 90˚ (M384) & 3-W
ay Overlap 1-1/2 Bullnose Corner Cap 90˚ (M
387)
181For more information or to contact a sales representative, see page 3
OvernightDelivery!
Available for
Vynyl Beads & Trim 173_186:DMF07_149 7/15/10 3:17 PM Page 187
3-W
ay O
ff-An
gle
Ove
rlap
3/4"
(M
134)
& 1
-1/2
" Bu
llnos
e C
orne
r C
aps
(M18
7)
182 The place to stop…before the building starts! SMrequest a quote online @
DMF Size Weight/Carton PackagingProduct Radius mm Style lbs kg Pcs/Box Boxes/SkidCodeM134 3/4 19 3-Way Off-Angle Corner Cap 3/4" 2.0 0.9 50 25
3-Way Off-Angle Overlap 3/4" Bullnose Corner Cap (M134)
Provides a professional finish at 135˚ off-angle, three-way 3/4" bullnose intersections.■ No need for special corner bead applications.
■ Easy to install.
■ Rust proof and dent resistant.
Provides a professional finish at three-way off-angle1-1/2" bullnose intersections.■ Substantially reduces labor.
■ No need for special corner bead applications.
■ Easy to install.
■ Rust proof and dent resistant.
Dietrich 3-way off-angle 1-1/2" bullnosecorner caps provide the ideal solutionto finish corners quickly and efficientlyat three-way off-angle 1-1/2" bullnose intersections. Thesecaps eliminate time-consumingmitering and create a professionaltransition. Easy to install, extended tabsand flanges ensure proper corneralignment.
DMF Size Weight/Carton PackagingProduct Radius mm Style lbs kg Pcs/Box Boxes/SkidCodeM187 1-1/2 38 3-Way Off-Angle Corner Cap 1-1/2" 2.0 0.9 50 25
3-Way Off-Angle 1-1/2" Bullnose Corner Cap (M187)
3-Way Off-AngleOverlap 3/4"BullnoseCorner Cap
Dietrich 3-way 135˚ off-angleoverlap 3/4" bullnose corner capsprovide the ideal solution to joinand finish corners at three-way off-angle 135˚ bullnose intersections.The bullnose cap eliminates time-consuming mitering and creates a professional transition.
3-Way Off-Angle 1-1/2" Bullnose Corner Cap
OvernightDelivery!
Available for
OvernightDelivery!
Available for
Vynyl Beads & Trim 173_186:DMF07_149 7/15/10 3:17 PM Page 188
Bullnose Corner and Transition CapsBullnose to 90˚ Transition C
ap (M859)
183For more information or to contact a sales representative, see page 3
Used to transition rounded bullnosecorners to 90˚ for easy baseboard and crown molding installation.■ Prevents gaps between bullnose corner bead
and baseboard or crown molding.
■ Eliminates need for time-consuming caulking and filling.
■ Used with baseboard or crown molding up to 4-1/2" in width.
■ For use with metal, vinyl or paper-faced corner beads.
Dietrich bullnose to 90˚ transitioncaps simplify installation ofbaseboard or crown moldingcorners into 3/4" bullnose systems.Quick and easy to install, thisproduct eliminates corner gaps andthe need for time-consumingcaulking and filling. Can be usedwith metal, vinyl or paper-faced3/4" bullnose corner bead fortransition onto baseboard or crownmolding up to 4-1/2" in width.
DMF Size Weight/Carton PackagingProduct Radius mm Style lbs kg Pcs/Box Boxes/SkidCode
M859 3/4 19Bullnose To 90˚
4.0 1.8 100 25Transition Cap 3/4"
Bullnose to 90˚ Transition Cap (M859)
Bullnose to 90˚ Transition Cap
Step 1 Step 2 Step 3
OvernightDelivery!
Available for
Vynyl Beads & Trim 173_186:DMF07_149 7/15/10 3:17 PM Page 189
Viny
l J-B
ead
(VLJ
B) &
Vin
yl M
udab
le J
-Bea
d (V
LMJ)
184 The place to stop…before the building starts! SMrequest a quote online @
Dietrich vinyl J-Bead provides a finished edge at gypsumboard stops around door and window openings and at ceilingintersections. Requires no joint compound. Rigid vinyl is not a thermal transmitter and helps stop condensation wheregypsum board terminates at exterior metal surfaces, such aswindow frames and mullions. Rust proof and dent resistant.
Creates a finished edge at gypsum stopsaround door and window openings and ceiling intersections.
■ Moisture anddent resistant.
■ Producesfinishededges at panelterminations.
■ Requires no jointcompound.
■ Nail or slip on.
Mudable J-Bead is used to cover and protect exposed ends of gypsum panels that abut toother substrates such as masonry, glass and metal frames. Raised shoulder and extensiveperforations along flange ensure excellent finishing compound adhesion and flush finish.Moisture- and thermal-resistant properties of rigid vinyl trims make for ideal use aroundbathtubs, showers, windows and skylights. Rust proof and dent resistant. Easy to cut andinstall. Available in 1/2" and 5/8" depths.
Mudable edge trim used to finish drywall edgeswhen dissimilar materials and door and window encasements meet gypsum.■ Moisture and dent resistant.
■ Raised shoulder and perforations enhance compound adhesion.
■ Produces finished edges at panel terminations.
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Boxes/Code Inches mm ft m Box Skid
1/2 12.78 2.44 16.0 7.2 50 25
VLMJ10 3.05 20.0 9.0 50 25
5/8 15.98 2.44 16.0 7.2 50 2510 3.05 20.0 9.0 50 25
Vinyl Mudable J-Bead (VLMJ)
J-Bead
Mudable J-Bead
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Boxes/Code Inches mm ft m Box Skid
1/2 12.78 2.44 20.0 9.0 50 35
VLJB10 3.05 25.0 11.3 50 35
5/8 15.98 2.44 20.0 9.0 50 3510 3.05 25.0 11.3 50 35
Vinyl J-Bead (VLJB)
Vynyl Beads & Trim 173_186:DMF07_149 7/15/10 3:17 PM Page 190
Vinyl Trims and Finishing ProductsVinyl L-Stop Bead (VLLS) & Vinyl Rip Bead
™L-Trim
(VLZL)
185For more information or to contact a sales representative, see page 3
Dietrich L-Stop Beadcreates a clean detail at gypsum panelterminations into doors,windows and ceilings.Easy attachment isattained with nails, screwsor staples to studsthrough bead flange.
Multiple perforations along 1-1/4" flange and raised shoulder
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Boxes/Code Inches mm ft m Box Skid
1/2 12.78 2.44 16.0 7.2 50 25
VLLS10 3.05 20.0 9.0 50 25
5/8 15.98 2.44 16.0 7.2 50 2510 3.05 20.0 9.0 50 25
Vinyl L-Stop Bead (VLLS)
Provides clean, sharp edge at wallboard terminations.■ Rust proof and dent resistant.
■ Raised shoulder and perforations enhance compound adhesion.
■ Produces finished edge at panel terminations.
enhance strong compound adhesion and provide for a flushfinish. Rigid vinyl is rust proof, dent resistant and easy to fieldcut without distorting profile or leaving sharp edges and burrs.Available in 1/2" and 5/8" depths; 8' and 10' lengths.
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Boxes/Code Inches mm ft m Box Skid
1/2 12.78 2.44 16.0 7.2 50 35
VLZL10 3.05 20.0 9.0 50 35
5/8 15.98 2.44 16.0 7.2 50 3510 3.05 20.0 9.0 50 35
Vinyl Rip Bead™ L-Trim (VLZL)
Creates a clean line at intersectionof gypsum board and ceiling grid.
■ Eliminates clean upand masking tape.
■ Rust proof and dent resistant.
■ Multiple perforationsenhance jointcompoundadhesion.
■ Produces clean,finished edges atpanel terminations.
DietrichVinyl Rip Bead™ L-Trim produces an exceptional finish at intersection of gypsum panels to ceiling grid, windowreturns and dissimilar wall types. A tear-away strip on the Rip Bead™
L-Trim provides a protective edge and a guide for the drywallfinishing knives. Once joint compound is applied, finished andpainted, the tear-away strip is removed to form a crisp, clean edge.Multiple perforations along the nailing flange enhance strongcompound adhesion. Available in 1/2" and 5/8" depths; 8' and 10'lengths.
L-Stop Bead
Rip Bead™
Vynyl Beads & Trim 173_186:DMF07_149 7/15/10 3:17 PM Page 191
Viny
l Par
titio
n En
d C
ap 1
/2"
(PC
50)
or 5
/8"
(PC
58)
& Vi
nyl 0
93 D
ryw
all C
ontro
l Joi
nt (
VCJT
)
186 The place to stop…before the building starts! SMrequest a quote online @
Dietrich vinylpartition end capsquickly finishdoorways, kneewalls and wallends bycapping theends of a walland providing a finish face.
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Boxes/Code Inches mm ft m Box SkidPC50 2-1/2 63.5 8 2.44 12.5 5.7 12 25(1/2") 3-5/8 92.1 10 3.05 15.6 7.1 12 25PC58 2-1/2 63.5 8 2.44 12.5 5.7 10 25(5/8") 3-5/8 92.1 10 3.05 15.6 7.1 10 25
Vinyl Partition End Cap for 1/2" Board (PC50) or 5/8" Board (PC58)
Vinyl partition end caps are designed with a special factory punched “T” slotted flange. The “T” slots can be cut easily to form arches or curves. This product provides time (cost) savings through single-pieceinstallation versus installing two corner beads. You also use lesscompound than two corner bead applications. Multipleperforations enhance strength of joint compound adhesion.Easy to cut, rust proof and dent resistant.
Quickly finishes doorways, knee walls and wall ends.■ One-piece installed cost savings.
■ Rust proof and dent resistant.
■ Simplifies product selection.
■ Easily forms arches or curves.
■ Available for 1/2“ and 5/8“ gypsum wallboard.
Dietrich Vinyl 093 Control Joint is applied between abutting gypsumpanels and is used to relieve stresses of expansion and contraction ofdrywall in large ceiling and wall expanses over 30'. Control joints areinstalled from door header to ceiling, from floor to ceiling in longpartition runs and from wall to wall in large ceiling areas.
Plastic tape protects 1/4" opening x 7/16" deep reveal and is removed aftercompound is applied and finished. Where sound transmission is aconsideration, an approved seal must be provided behind control joint. Usemetal control joints wherever fire ratings are a concern.
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Boxes/Code Inches mm ft m Box SkidVCJT 3/32 2.4 10 3.05 42.0 19.0 60 25
Vinyl 093 Drywall Control Joint (VCJT)
Used to relieve expansion and contraction stresses.
Partition End Cap
Vinyl 093ControlJoint
Ceiling Application
■ Use with drywall or veneer plaster.
■ Moisture resistant and rust proof.
■ Maintains profile after cutting.
■ Perforations enhance compound adhesion.
Wall Application
Vynyl Beads & Trim 173_186:DMF07_149 7/15/10 3:18 PM Page 192
187
Drywall Beads and Trims (Paper-Faced) Paper-Faced Metal Outside Corner,Tape-On Bead (G1WO, G1UO, G1XW,G1XU, G1SU) ......................................190Paper-Faced Metal Offset OutsideCorner, Tape-On Bead (G100)......191Paper-Faced Inside Corner Tape-OnBead (G2I) ............................................192Paper-Faced Off-Angle Inside CornerTape-On Bead (G20I) ......................193Paper-Faced Bullnose Corner BeadsPaper-Faced 3/4" Bullnose OutsideCorner, Tape-on Bead (G1BO)......194Paper-Faced 3/4" Bullnose Off-AngleOutside Corner, Tape-On Bead(GOBO) ..................................................195Paper-Faced 3/4" Bullnose OutsideCorner, Nail-On Bead (G1BN) ......196Paper-Faced 3/4" Bullnose OffsetOutside Corner, Nail-On Bead (GOOB) ..................................................197Paper-Faced Trims and Finishing ProductsPaper-Faced Inner Cove, Tape-On Trim(G2B1)....................................................198Paper-Faced Metal L, Tape-On Trim(G4L) ......................................................199Paper-Faced Metal Reveal, Tape-OnTrim (GGR)............................................200
187-200 Paper Bead:DMF07_163 7/15/10 4:06 PM Page 187
Pape
r-Fac
ed B
eads
& T
rims
Ove
rvie
w
188 The place to stop…before the building starts! SMrequest a quote online @
PAPER-FACEDBEADS & TRIMS
OVERVIEWPaper-faced metal beads and trimscombine galvanized metal cornerand edge protection with high-gradepaper tape to provide cost-effective,problem-free, compound-embeddeddrywall finishing. Paper-faced beadsvirtually eliminate any potential forcorner and edge cracking by movingor floating with the gypsum inde-pendent of framing movement or set-tling. The result is a precise, high-quality, straight and smooth finish,free from unsightly cracks, chips andnail pops.
Tape-on paper-faced beads andtrims are not fastened directly to theframing like conventional nail-onbead. Joint compound is applied tothe underside of the paper flanges,aligned and pressed into place. Jointcompound seeps through perforatedholes in the paper to provide superi-or adhesion and bonding to the gyp-sum paper.
Nail-on paper-faced beads and trimsare also available. Nail-on trims areused when nailing or mechanicalfastening is desired or required, butpaper facing is preferred for appli-cation at joint treatment.
Advantages
Goldline* paper-faced products are recognized as the premier paper-faced finishingproducts. Here are a few of the reasons many finishers simply demand Goldline®:
■ Virtually impervious to scuffing and “fluffing-up.”
■ Will not be damaged by sanding.
■ Does not require nose coating.
■ Uniformly durable throughout the paper’s thickness.
■ Enhanced compound bonding during application.
■ Enhanced paintability.
■ Fewer call backs for repairs.
■ The smoothest finish available.
■ The most dimensionally stable paper in the industry.
*Goldline® is a registered trademark of Corus CIC, Inc.
187-200 Paper Bead:DMF07_163 7/15/10 4:06 PM Page 188
OverviewPaper-Faced Beads & Trim
s Overview
189For more information or to contact a sales representative, see page 3
Goldline* paper-facedmetal products are avail-able in a wide variety ofprofiles. The 90˚ outsidecorners have a numberof different metal andpaper widths that reflectthe demand of a specificmarket or application.Wide flanged beads areused when finisherswant a product that will
cover an imperfect drywall corner (drywall stops short of cor-ner, crooked house wall, etc.). Splayed angle outside cornersare available to accommodate 120˚/135˚ corners.
Inside metal corners areavailable for both 90˚and 120˚/135˚. Thesame profile angles forboth outside and insidecorners are available in3/4" radius bullnose aswell. L-trims are alsoavailable in a wide rangeof sizes. These productsare used to trim wall-board where it abuts
with other building components such as suspended ceilings,beams, concrete or untrimmed door and window jambs.
*Goldline® is a registered trademark of Corus CIC, Inc.
Laramie Drywall has buildersthat demand paper-faced corner bead. Dietrich’s Goldline®
bead is our product of choice.Goldline® doesn't ball, nap orfuzz when sanded. Goldline®
means a better job for theowner and less call backs forus. The bottom line is a win–winfor everyone.— Wil Laramie
Laramie Drywall CompanySt. Charles, MO
187-200 Paper Bead:DMF07_163 7/15/10 4:06 PM Page 189
Pape
r-Fac
ed M
etal
Out
side
Cor
ner,
Tape
-On
Bead
(G
1WO
, G1U
O, G
1XW
, G1X
U, G
1SU
)
190 The place to stop…before the building starts! SMrequest a quote online @
DMF USG Dimensions (Inches) Weight/Carton PackagingProduct Reference Style A B C D lbs kg Pcs/Box Boxes/SkidCode
G1WO B1W Standard Leg 1/2 3/4 7/8 7/8 40.0 18.1 50 40G1UO B1EL Equal Leg 3/4 3/4 3/4 3/4 46.0 20.8 50 40G1XW B1XW Extra Wide 7/8 5/8 5/8 3/4 46.0 20.8 50 40G1XU B1XW EL Extra Wide Equal 7/8 7/8 5/8 5/8 53.0 24.0 50 40G1SU B1 Super Wide Super Wide Equal 1-1/8 1-1/8 5/8 5/8 66.0 29.9 50 40
All carton weights are calculated based on 10' lengths.Standard lengths are 8', 9' and 10'. Other lengths available.*Goldline is a registered trademark of Corus CIC Inc.
Dietrich Metal Framing does not manufacture, license or sell products sold under the USG/Beadex product codes and that such codes are listed for cross reference/comparison purposes only.
Paper-Faced MetalOutside Corner, Tape-On Bead
Superior 90˚ outside corner drywall finishing tape-on beadeliminates unsightly corner cracks, chips and nail pops.■ Virtually eliminates costly callbacks.
■ Substantially reduces joint compound consumption and eliminates one finish coat.
■ Does not require mechanical fastening (no nails, staples, screws or crimps).
■ Impervious to “scuffing” and “fluffing-up.”
■ Will not be damaged by sanding.
■ Superior adhesion, bonding and paintability.
■ Does not require nose coating.
Extra Wide Leg
Standard Leg
Goldline* paper-faced tape-on beads combine galvanized metal corner and edge protectionwith high-grade paper tape to provide cost-effective, problem-free outside drywall cornerfinishing. Paper-faced beads are available in a number of different widths to suit mostwallboard applications. Wider flange beads are used to cover imperfect corners, while shorter flanges are used to achieve maximum efficiency.
Paper-faced beads virtually eliminate corner cracks, edge chips and nail pops. These beads are applied using joint compound that embeds the paper bead to the wallboard paper. Nomechanical fasteners like nails, screws, staples or crimps are used. Although paper-faced beadsdo cost more compared to traditional metal and vinyl, they provide reduced labor and materialsby reducing the amount of joint compound needed and also eliminate one pass of finishing.
U.S. Patent Nos. 5,613,335and 5,836,122
187-200 Paper Bead:DMF07_163 7/15/10 4:06 PM Page 190
Drywall Beads and Trims (Paper-Faced)Paper-Faced M
etal Offset O
utside Corner, Tape-O
n Bead (G100)
191For more information or to contact a sales representative, see page 3
Goldline* off-angle tape-on bead, also known as splayed or120/135˚ corner bead, is used to provide a strong, smoothfinish for outside off-angle drywall intersections. Paper-facedtape-on off-angle bead is applied in the same manner as 90˚paper bead. Joint compound is used to embed the paper-faced bead to the wallboard paper. The result is a clean,crisp, durable off- angle corner that will not crack or chip.
U.S. Patent Nos. 5,613,335 and 5,836,122
DMF USG Dimensions (Inches) Weight/Carton PackagingProduct Reference Style A B C D lbs kg Pcs/Box Boxes/SkidCodeG100 B1 OS Off-Angle 1/2 3/4 5/8 5/8 40.0 18.1 50 40
All carton weights are calculated based on 10' lengths.Standard lengths are 8', 9' and 10'. Other lengths available.*Goldline is a registered trademark of Corus CIC Inc.
Dietrich Metal Framing does not manufacture, license or sell products sold under the USG/Beadex product codes and that such codes are listed for cross reference/comparison purposes only.
Paper-Faced Metal Off-Angle Outside Corner, Tape-On Bead (G100)
High-performance off-angle tape-on bead is ideal for finishing 120˚/135˚ offset corners.■ Virtually eliminates costly callbacks.
■ Impervious to “scuffing” and “fluffing-up.”
■ Will not be damaged by sanding.
■ Substantially reduces joint compound consumption and eliminates one finish coat.
■ Does not require mechanical fastening (no nails, staples, screws or crimps).
■ Superior adhesion, bonding and paintability.
■ Does not require nose coating. Splayed Bead
187-200 Paper Bead:DMF07_163 7/15/10 4:06 PM Page 191
Pape
r-Fac
ed In
side
Cor
ner
Tape
-On
Bead
(G
2I)
Goldline* tape-on inside 90˚ paper-faced corner beadprovides very straight and precise inside corners. The rigidsteel-reinforced inside corners provide a durable guide toachieve exceptionally straight and sharp inside corners.Paper-faced inside corners are embedded in jointcompound and pressed firmly into place. Excesscompound is removed with a drywall knife.
U.S. Patent Nos. 5,613,335 and 5,836,122
DMF USG Dimensions (Inches) Weight/Carton PackagingProduct Reference Style A B C D lbs kg Pcs/Box Boxes/SkidCodeG2I B2 Standard Angle 3/8 3/8 5/8 5/8 26.0 11.8 50 40
All carton weights are calculated based on 10' lengths.Standard lengths are 8', 9' and 10'. Other lengths available.*Goldline is a registered trademark of Corus CIC Inc.
Dietrich Metal Framing does not manufacture, license or sell products sold under the USG/Beadex product codes and that such codes are listed for cross reference/comparison purposes only.
Paper-Faced Inside Corner Tape-On Bead (G2I)
Provides incredibly straight and smooth inside90˚ corners for drywall finishing.■ Virtually eliminates costly callbacks.
■ Impervious to “scuffing” and “fluffing-up.”
■ Will not be damaged by sanding.
■ Substantially reduces joint compound consumption and eliminates one finish coat.
■ Does not require mechanical fastening (no nails, staples, screws or crimps).
■ Superior adhesion, bonding and paintability.
■ Does not require nose coating.
192 The place to stop…before the building starts! SMrequest a quote online @
Inside Corner
187-200 Paper Bead:DMF07_163 7/15/10 4:06 PM Page 192
Drywall Beads and Trims (Paper-Faced)
Goldline* off-angle tape-on 120/135˚ inside or reversesplayed bead is used to achieve a crisp, clean, straight-finished inside off-angle drywall finish. This bead can be usedfor inside corner angles between 120˚ and 135˚. As with alltape-on beads, off-angle bead is applied using jointcompound. No mechanical fasteners are required.
U.S. Patent Nos. 5,613,335 and 5,836,122
DMF USG Dimensions (Inches) Weight/Carton PackagingProduct Reference Style A B C D lbs kg Pcs/Box Boxes/SkidCodeG20I B2 OS Off-Angle 5/8 5/8 5/8 5/8 45.0 20.4 50 40
All carton weights are calculated based on 10' lengths.Standard lengths are 8', 9' and 10'. Other lengths available.*Goldline is a registered trademark of Corus CIC Inc.
Dietrich Metal Framing does not manufacture, license or sell products sold under the USG/Beadex product codes and that such codes are listed for cross reference/comparison purposes only.
Paper-Faced Metal Off-Angle Inside Corner Tape-On Bead (G20I)
Used to create a sharp, crisp line for finishinginside off-angle or inverted splayed corners.■ Virtually eliminates costly callbacks.
■ Impervious to “scuffing” and “fluffing-up.”
■ Will not be damaged by sanding.
■ Substantially reduces joint compound consumption and eliminates one finish coat.
■ Does not require mechanical fastening (no nails, staples, screws or crimps).
■ Superior adhesion, bonding and paintability.
■ Does not require nose coating.
Paper-Faced Off-Angle Inside C
orner Tape-On Bead (G
20I)
193For more information or to contact a sales representative, see page 3
Inside SplayedCorner
187-200 Paper Bead:DMF07_163 7/15/10 4:06 PM Page 193
Pape
r-Fac
ed 3
/4"
Bulln
ose
Out
side
Cor
ner,
Tape
-On
Bead
(G
1BO
)
194 The place to stop…before the building starts! SMrequest a quote online @
Creates elegant, rounded outside drywall corners addingcontemporary styling and a sense of openness to any room.■ Virtually eliminates costly callbacks.
■ Impervious to “scuffing” and “fluffing-up.”
■ Will not be damaged by sanding.
■ Substantially reduces joint compound consumptionand eliminates one finish coat.
■ Does not require mechanical fastening (No nails, staples, screws or crimps).
■ Superior adhesion, bonding and paintability.
Goldline* 3/4" tape-on bullnose corner bead is used tocreate a smooth, rounded look to standard drywall corners.Paper-faced bullnose bead adds contemporary styling and a sense of openness to any room. Tape-on bullnose isapplied in the same manner as all other tape-on beads.Joint compound is used to embed the paper-faced bead to the wallboard paper. The result is a beautiful, roundedcorner that will not crack or chip.
U.S. Patent Nos. 5,613,335 and 5,836,122
DMF USG Dimensions (Inches) Weight/Carton PackagingProduct Reference Style A B C lbs kg Pcs/Box Boxes/SkidCodeG1BO SLOC Standard 7/8 3/4 7/8 53.0 24.0 50 40
All carton weights are calculated based on 10' lengths.Standard lengths are 8', 10'. Other lengths available.*Goldline is a registered trademark of Corus CIC Inc.
Dietrich Metal Framing does not manufacture, license or sell products sold under the USG/Beadex product codes and that such codes are listed for cross reference/comparison purposes only.
Paper-Faced 3/4 BullnoseOutside Corner, Tape-On Bead (G1BO)
Tape-on Bullnose
Gypsum boardpanels must becut back 3/4" toaccommodatethe bullnoseradius andensure a flush fit.
187-200 Paper Bead:DMF07_163 7/15/10 4:07 PM Page 194
Paper-Faced Bullnose Corner BeadsPaper-Faced 3/4" Bullnose O
ff-Angle Outside C
orner, Tape-On Bead (G
OBO
)
195For more information or to contact a sales representative, see page 3
DMF USG Dimensions (Inches) Weight/Carton PackagingProduct Reference Style A B C lbs kg Pcs/Box Boxes/SkidCodeG0BO SLOC OS Off-Angle 1 3/4 1 53.0 24.0 50 40
All carton weights are calculated based on 10' lengths.Standard lengths are 8', 10'. Other lengths available.*Goldline is a registered trademark of Corus CIC Inc.
Dietrich Metal Framing does not manufacture, license or sell products sold under the USG/Beadex product codes and that such codes are listed for cross reference/comparison purposes only.
Paper-Faced 3/4 Bullnose Off-AngleOutside Corner, Tape-On Bead (GOBO)
Offset bullnose provides rounded 120˚–135˚ outsidedrywall corners for a contemporary “modern“ look.■ Virtually eliminates costly callbacks.
■ Impervious to “scuffing” and “fluffing-up.”
■ Will not be damaged by sanding.
■ Substantially reduces joint compound consumption and eliminates one finish coat.
■ Does not require mechanical fastening (No nails, staples, screws or crimps).
■ Superior adhesion, bonding and paintability.
Gypsum board panels must be cut back 3/4" toaccommodate the bullnose radius and ensure a flush fit.
Splayed Bullnose
Goldline* off-angle bullnose tape-on bead, also known assplayed bullnose or 120/135˚ bullnose corner bead is used to provide a rounded, bullnose finish for off-angle drywallintersections. Paper-faced tape-on off-angle bullnose bead is applied in the same manner as 90˚ paper bead. Jointcompound is used to embed the paper- faced bead to thewallboard paper. The result is a clean, crisp, rounded off-angle corner that will not crack or chip.
U.S. Patent Nos. 5,613,335 and 5,836,122
187-200 Paper Bead:DMF07_163 7/15/10 4:07 PM Page 195
Pape
r-Fac
ed 3
/4"
Bulln
ose
Out
side
Cor
ner,
Nai
l-On
Bead
(G
1BN
)
DMF USG Dimensions (Inches) Weight/Carton PackagingProduct Reference Style A B C lbs kg Pcs/Box Boxes/SkidCodeG1BN SLOC N Standard 5/8 3/4 5/8 72.0 32.6 50 40
All carton weights are calculated based on 10' lengths.Standard lengths are 8', 10'. Other lengths available.*Goldline is a registered trademark of Corus CIC Inc.
Dietrich Metal Framing does not manufacture, license or sell products sold under the USG/Beadex product codes and that such codes are listed for cross reference/comparison purposes only.
196 The place to stop…before the building starts! SMrequest a quote online @
■ Virtually eliminates costly callbacks.
■ Impervious to “scuffing” and “fluffing-up.”
■ Will not be damaged by sanding.
■ Substantially reduces joint compoundconsumption and eliminates one finish coat.
■ Superior adhesion, bonding and paintability.
Goldline* 3/4" nail-on bullnose corner bead is used tocreate a smooth, rounded look to standard drywall corners.Nail-on bullnose adds contemporary styling and a sense ofopenness to any room.
Provides the same elegant and contemporary roundeddrywall corners as tape-on and is used when nailing ormechanical fastening is desired.
Nail-On Bullnose
Gypsum board panels must be cut back 3/4" toaccommodate the bullnose radius and ensure a flush fit.
Paper-Faced 3/4 BullnoseOutside Corner, Nail-On Bead (G1BN)
Nail-on bead is applied in the same manner as traditionalmetal and vinyl beads. Nails or mechanical fasteners areused to secure the bead to the wallboard. Wide flange nail-on-bullnose is also available.
U.S. Patent Nos. 5,613,335 and 5,836,122
187-200 Paper Bead:DMF07_163 7/15/10 4:07 PM Page 196
Paper-Faced Bullnose Corner Beads
Nail-on offset bullnose is used to provide rounded 120˚–135˚ outside drywall cornerswhen nailing or mechanical fasteningis desired or required.■ Virtually eliminates costly callbacks.
■ Impervious to "scuffing" and "fluffing-up".
■ Will not be damaged by sanding.
■ Substantially reduces joint compound consumption and eliminates one finish coat.
■ Superior adhesion, bonding and paintability.
Goldline* off-angle nail-on bullnose bead, also known assplayed bullnose or 120˚–135˚ bullnose corner bead, is usedto provide a rounded bullnose finish for outside off-angledrywall intersections.
Off-angle nail-on bead is applied in the same manner astraditional or vinyl off-angle bullnose. Nails or mechanicalfasteners are used to secure the bead to the wallboard.
U.S. Patent Nos. 5,613,335 and 5,836,122
DMF USG Dimensions (Inches) Weight/Carton PackagingProduct Reference Style A B C lbs kg Pcs/Box Boxes/SkidCodeG00B SLOC NOS Off-Angle 5/8 3/4 5/8 68.0 30.8 50 40
All carton weights are calculated based on 10' lengths.Standard lengths are 8', 10'. Other lengths available.*Goldline is a registered trademark of Corus CIC Inc.
Dietrich Metal Framing does not manufacture, license or sell products sold under the USG/Beadex product codes and that such codes are listed for cross reference/comparison purposes only.
Paper-Faced 3/4 Bullnose Offset Outside Corner, Nail-On Bead (GOOB)
Paper-Faced 3/4" Bullnose Offset O
utside Corner, N
ail-On Bead (G
OO
B)
197For more information or to contact a sales representative, see page 3
Gypsum board panels must be cut back 3/4" toaccommodate the bullnose radius and ensure a flush fit.
Nail-On Splayed
187-200 Paper Bead:DMF07_163 7/15/10 4:07 PM Page 197
Pape
r-Fac
ed In
ner
Cov
e, T
ape-
On
Trim
(G
2BI)
198 The place to stop…before the building starts! SMrequest a quote online @
Goldline* tape-on inner cove 90˚ paper-faced beadprovides subtle, rounded inside or inner corners. Innercove tape on beads are embedded in joint compound andpressed firmly into place. Excess compound is removedwith a drywall knife or wiped clean with a rag.
U.S. Patent Nos. 5,613,335 and 5,836,122
DMF USG Dimensions (Inches) Weight/Carton PackagingProduct Reference Style A B C lbs kg Pcs/Box Boxes/SkidCodeG2BI SLIC Standard 5/8 3/4 5/8 53.0 24.0 50 40
All carton weights are calculated based on 10' lengths.Standard lengths are 8', 10'. Other lengths available.*Goldline is a registered trademark of Corus CIC Inc.
Dietrich Metal Framing does not manufacture, license or sell products sold under the USG/Beadex product codes and that such codes are listed for cross reference/comparison purposes only.
Paper-Faced Inner Cove,Tape-On Trim (G2BI)
Creates subtle, smooth, rounded inside or inner cove corners.■ Virtually eliminates costly callbacks.
■ Impervious to “scuffing“ and “fluffing-up.“
■ Will not be damaged by sanding.
■ Substantially reduces joint compound consumption and eliminates one finish coat.
■ Does not require mechanical fastening (No nails, staples, screws or crimps).
■ Superior adhesion, bonding and paintability.
Inner Cove Tape-On
187-200 Paper Bead:DMF07_163 7/15/10 4:07 PM Page 198
Paper-Faced Trims and Finishing ProductsPaper-Faced M
etal L, Tape-On Trim
(G4L)
199For more information or to contact a sales representative, see page 3
Goldline* L-Trims are used to finish the ends of wallboardwhere it abuts dissimilar surfaces such as suspended ceilings,beams, plaster, masonry or untrimmed door and windowjambs. Tape-on L-Trims are applied in the same manner as allother tape-on beads. Joint compound is used to embed thepaper-faced bead to the wallboard paper. Excess compoundcan be removed with a drywall knife or clean rag.
U.S. Patent Nos. 5,613,335 and 5,836,122
DMF USG Dimensions (Inches) Weight/Carton PackagingProduct Reference Style A B C lbs kg Pcs/Box Boxes/SkidCode
B4 3/8 7/16 1-11/16 1-1/4 40.0 18.1 50 40G4L B4 1/2 9/16 15/16 1-1/4 42.0 19.0 50 40
B4 5/8 11/16 1-1/16 1 44.0 19.9 50 40
All carton weights are calculated based on 10' lengths.Standard lengths are 8', 10'. Other lengths available.*Goldline is a registered trademark of Corus CIC Inc.
Dietrich Metal Framing does not manufacture, license or sell products sold under the USG/Beadex product codes and that such codes are listed for cross reference/comparison purposes only.
Paper-Faced Metal L, Tape-On Trim (G4L)
L-Trim
Protects and finishes wallboard edge when gypsum panels abut dissimilar surfaces.■ Virtually eliminates costly callbacks.
■ Impervious to “scuffing“ and “fluffing-up.“
■ Will not be damaged by sanding.
■ Substantially reduces joint compound consumption andeliminates one finish coat.
■ Does not require mechanical fastening (No nails, staples,screws or crimps).
■ Superior adhesion, bonding and paintability.
■ Does not require nose coating.
187-200 Paper Bead:DMF07_163 7/15/10 4:07 PM Page 199
Pape
r-Fac
ed M
etal
Rev
eal,
Tape
-On
Trim
(G
GR)
200 The place to stop…before the building starts! SMrequest a quote online @
Goldline* reveal trims are used to finish wallboardterminations when the board abuts other buildingmaterials such as suspended ceilings, beams, plaster,masonry and untrimmed door and window jambs to createa clean step inset or reveal. Reveals help create subtle,aesthetic architectural detailing around light fixtures,ceilings, walls and soffits.
Paper-faced tape-on reveals are installed using jointcompound to embed the reveal and secure it to thewallboard. No mechanical fasteners are required.
U.S. Patent Nos. 5,613,335 and 5,836,122
DMF USG Dimensions (Inches) Weight/Carton PackagingProduct Reference Style A B C D lbs kg Pcs/Box Boxes/SkidCode
GGRB4 NB Reveal (1/2") 1/2 x 1/2 1/2 1/2 1-3/16 7/8 40.0 18.1 50 40B4 NB Reveal (5/8") 5/8 x 5/8 5/8 5/8 15/16 7/8 40.0 18.1 50 40
All carton weights are calculated based on 10' lengths.Standard lengths are 8', 10'. Other lengths available.*Goldline is a registered trademark of Corus CIC Inc.
Dietrich Metal Framing does not manufacture, license or sell products sold under the USG/Beadex product codes and that such codes are listed for cross reference/comparison purposes only.
Paper Faced Metal Reveal,Tape-On Trim (GGR)
Paper-Faced Reveal
Used to create gentle insets or step-ins foraesthetically pleasing architectural detailing.■ Also known as “race track” bead.
■ Virtually eliminates costly callbacks.
■ Impervious to “scuffing“ and “fluffing-up.“
■ Will not be damaged by sanding.
■ Substantially reduces joint compoundconsumption and eliminates one finish coat.
■ Does not require mechanical fastening (No nails, staples, screws or crimps).
■ Superior adhesion, bonding and paintability.
■ Does not require nose coating.
187-200 Paper Bead:DMF07_163 7/15/10 4:07 PM Page 200
201
Veneer Beads and TrimsMini-Bead™ 800/900 Galvanized (MB80/MB90) Zinc (ZB80/ZB90)..............................204093 Zinc Control Joint (ZNCJ) ......205#701A Metal J-Trim with 3/32"Grounds (M71A/Z71A) and with 1/16" Grounds (M81A/Z81A) ......206#701B Metal L-Trim with 3/32"Grounds (M71B/Z71B) and with 1/16" Grounds (M81B/Z81B) ......207Stucco and Plaster Casing Beads1A Expanded Flange Corner Bead—Galvanized (CBXA), Zinc (CBZA) ..208Double-X™ Corner Bead—Galvanized (CBXX) ............................209Strip Lath (LAST) ................................210Cornerite™ (XRIT) ................................211#66 Expanded Flange Casing Bead—Galvanized (XXCB), Zinc (XXZB)....212#66 Expanded Flange Casing Bead with Weep Holes—Galvanized (XXCW), Zinc (XXZW) ..212#66 N Short Flange Casing Bead—Galvanized (SFCB), Zinc (SFZB)....214#66 N Short Flange Casing Bead with Weep Holes—Galvanized (SFWB) ............................215Stucco and Plaster Control JointsCorner Master™ #30 (CR30) ..........216Zinc Control Joints 38 (ZCJ3), 50 (ZCJ5), 75 (ZCJ7), 100 (ZCJ1) ....................217Double-V Expansion Control Joint—Galvanized (VVCJ), Zinc (VVZJ) ....218Double-J Expansion Control Joint—Galvanized (XJ15), Zinc (ZJ15) ....219Expansion Joint #40—Galvanized(EJ40), Zinc (EZ40) ..........................220Stucco, Screeds and ExteriorFinishing ProductsF.H.A.7. Foundation Weep Screed (FHA7) ....................................................2217/8" Sill Screed (SI36) ....................2221-3/8" J-Weep with 2" Nailing Flange (JCLB), with Weep Holes (JWLB) ................223J-Weep High-Back Plaster Stop (JWP)..............................224
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:19 PM Page 201
202 The place to stop…before the building starts! SMrequest a quote online @202 The place to stop…before the building starts! SMrequest a quote online @
Vene
er, S
tucc
o &
Plas
ter
Bead
s &
Trim
s O
verv
iew
VENEER,STUCCO &PLASTER
BEADS & TRIMSOVERVIEW
Veneer plaster continues to grow inpopularity as a wall finishing system.The speed of application for one-coatsystems makes it competitive withdrywall, and the added smoothnessof two-coat veneer provides a look ofluxury and adds ease to decorating.In either case, the toughness ofveneer plaster makes walls moredurable and resistant to scuffs,gouges and impact damage.
Having the right metal trims, controljoints and corner reinforcements isan integral part of the wall system’sappearance and long-term perform-ance. That’s why Dietrich MetalFraming takes such care in the man-ufacturing of these components. Ourhistory in the manufacturing ofmetal lath and accessories for con-ventional plaster gives us uniqueknowledge of this growing trade andthe product quality that is requiredto do the job right.
Advantages
Strength—Veneer and plaster are used to cre-ate strong, durable finishes resistant to scuffs,gouges, dents and abrasions.
Superior Finish—Expanded mesh and rigidpronounced edges provide excellent keyingand exacting grounds for superior bonding andfinishing to minimize cracks and shadowing.
Corrosion Resistant—Galvanized or zinc formaximum corrosion protection. Zinc productsshould be used in exterior applications.
As the largest specialty wallboard, metal, and ceilings distributor in the United States, servicing the needs of commercial contractors from coast tocoast, L&W Supply looks to Dietrich Metal Framingas a key vendor to supply a broad metal framingand accessory product offering, satisfying our cus-tomers’ job requirements in a timely manner. And,they have been doing that for over 20 years.— Michael C. Lorimer
President, Chief Operating OfficerL&W Supply Corporation
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:19 PM Page 202
203For more information or to contact a sales representative, see page 3 203For more information or to contact a sales representative, see page 3
OverviewVeneer, Stucco & Plaster Beads & Trim
s Overview
Styles & Types
Veneer Corner Beadsare designed to protectinterior corners and to establish suitablegrounds for veneer finishes.
Veneer Trims 701Aand 801A are J-shapedtrims that come in differ-
ent depths and grounds to accommodate veneer finishes.Sized to fit 1/2" and 5/8" gypsum plaster base, 701A groundsare 3/32" for two-coat veneer and 801A grounds are 1/16" forone-coat veneer plaster. Also available in zinc for cementboard applications.
Veneer Trims 701B and 801B are L-shaped trims designedfor use at the junction of veneer gypsum board base withrough concrete or masonry ceilings. They are sized to fit 1/2"and 5/8" gypsum board plaster base. 701B grounds are 3/32"for two-coat veneer, and 801B grounds are 1/16" for one-coatveneer plaster. Use zinc finish for exterior applications.
Expanded Corner Beads are designed to protect outsidecorners and to establish suitable grounds for plaster and stuc-co finishes.
Cornerite should be used on interior corner angles wherethe lath has been spliced or where additional reinforcement isdesired. It should be wire tied to the lath using 18-gauge wire.
Strip Lath is a flat expanded metal strip used as plaster rein-forcement over joints of non-metallic lathing bases and wheredissimilar bases join. It’s commonly attached diagonally at thecorners of doors, windows or areas prone to cracks.
Expanded Flange Casing Beads are used to ensure theproper stucco thickness. They are recommended for use withmetal lath and masonry units.
Dietrich #66 ShortFlange Casing Beadsare used as a universalplaster stop at door andwindow openings, wallterminations and inter-sections.
Control & ExpansionJoints are used in largeuninterrupted plasteredareas to relieve stressand minimize cracking.
Foundat ion WeepScreeds protect thestop edges of stucco atthe sill plate line. Holesin the flange allow someweeping, but the angularsurface of the bead isdesigned to facilitate theegress of moisturebehind the cementitiousmembrane.
1-3/8" J-Weep is primarily used as a starter track at the bot-tom of the wall for 3/8" one-coat stucco over 1" foam.
Mini-Bead™ 900 Zinc is a zinc bead used for external cornerreinforcements. It has 1-1/4" wide fine-mesh expanded flangestapered along outer edges for improved concealment and eas-ier finishing with E.I.F.S. basecoats and finishes.
NOTE: Dietrich Metal Framing recommends the use ofzinc or vinyl for all exterior applications.
CAUTION: Joints and corners are a potential point ofwater intrusion. Dietrich strongly recommends build-ing paper be placed behind all joints and corners.Also, a bead of high-quality caulking should beapplied under the joints prior to the attachment of thematerials.
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:20 PM Page 203
204 The place to stop…before the building starts! SMrequest a quote online @
Min
i-Bea
d™80
0/90
0 G
alva
nize
d (M
B80/
MB9
0) Z
inc
(ZB8
0/ZB
90)
204 The place to stop…before the building starts! SMrequest a quote online @
Dietrich Mini-Bead™ 800/900 are fine-mesh corner beadsused to provide corner reinforcement for one- and two-coat veneer plaster systems. 1-1/4" wide fine-mesh flangesare tapered along the outer edges to enhance veneerplaster concealment. MB80 has 1/16" grounds for one-coatveneer plaster and 90 keys per linear foot for excellentbonding and strong, secure corners. MB90 has 3/32"grounds associated with two-coat veneer plaster systems.Zinc Mini-Bead™ (ZB80/ZB90) corner beads should be usedin exterior finish systems. Flange attachments can beaccomplished by nailing, stapling or clinching.
DMF Size Weight/Carton PackagingProduct Grounds Width Length lbs kg Pcs/ Carton/Code Inches mm ft m Carton SkidMB80 1/16" 1-1/4 31.8 8 2.44 33.6 15.2 60 25MB90 3/32" 1-1/4 31.8 10 3.05 42.0 19.0 60 25ZB80** 1/16" 1-1/4 31.8 10 3.05 29.9 13.5 60 25ZB90** 3/32" 1-1/4 31.8 10 3.05 37.3 16.9 60 25
* Kal-Korner™ is a registered trademark of National Gypsum Company.** Zinc
Mini-Bead™ 800/900 Galvanized (MB80/MB90) Zinc (ZB80/ZB90)
Corner reinforcement for one- and two-coatveneer “thin wall” plaster systems.■ Mini-mesh flanges for plaster keying and eliminates shadowing.
■ Galvanized or zinc for corrosion protection.
■ Excellent alternative to Kal-Korner™.
Mini-Bead™
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:20 PM Page 204
205For more information or to contact a sales representative, see page 3
Veneer Beads and Trims093 Zinc C
ontrol Joint (ZNC
J)
For more information or to contact a sales representative, see page 3
Dietrich 093 ZincControl Joint is appliedbetweenabuttinggypsum panelsand used torelieve stressesof expansionand
contraction of drywall and veneer plaster systems in wallexpanses over 30 feet and ceiling areas exceeding 2,500square feet. It’s installed from door header to ceiling, fromfloor to ceiling in long partition runs, and from wall to wall in large ceiling areas or in areas where framing or furringchange direction. Plastic tape protects 1/4" opening, 7/16"depth, and is removed after compound or plaster is appliedand finish is completed.
Zinc Control Joints are manufactured from high-quality zincand can be used for interior or exterior applications.
NOTE: Where fire and sound control are primeconsiderations, a seal must be attached behind the control joint.
DMF Size Weight/Carton PackagingProduct Grounds Length lbs kg Pcs/ Carton/Code Inches mm ft m Carton SkidZNCJ 3/32 2.4 10 3.05 22.5 10.2 25 64
093 Zinc Control Joint (ZNCJ)
Relieves stresses of expansion and contraction acrosslarge ceiling and wall areas.■ Relieves stresses of expansion and contraction.
■ Superior corrosion resistance.
■ Easy to apply and finish.
■ Use with drywall veneer plaster.
Zinc Control Joint
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:20 PM Page 205
206 The place to stop…before the building starts! SMrequest a quote online @
#70
1A M
etal
J-T
rim w
ith 3
/32"
Gro
unds
(M
71A/
Z71A
) an
d w
ith 1
/16"
Gro
unds
(M
81A/
Z81A
)
206 The place to stop…before the building starts! SMrequest a quote online @
Dietrich veneer trimsM71A and M81A are J-shaped trims formedfrom galvanized steelto fit standard 1/2"and 5/8" gypsumpanel depths withgrounds toaccommodate veneerfinishes. These trimsprovide clean, neatedge protection forone- or two-coatveneer plaster
finishes at gypsum panel terminations to wall openings andwall or ceiling intersections. M71A provides 3/32" groundsfor two-coat veneers and M81A has 1/16" grounds for one-coat veneer plaster.
Dietrich Z71A and Z81A veneer trims are the zincequivalents of M71A and M81A with the added benefit ofproviding ultimate corrosion protection for cement boardand exterior applications. These trims provide clean, neatedge protection at wall or ceiling intersections, or wallterminations for one- and two-coat veneer plaster systems.
Provides clean, neat edge protection at gypsum panelterminations for one- and two-coat veneer plaster finishes.■ Mini-mesh flanges for plaster keying.
■ Eliminates shadowing.
■ Galvanized coated or zincfor corrosion protection.
J-Trim
DMF Size Weight/Carton PackagingProduct Grounds Width Length lbs kg Pcs/ Carton/Code Inches mm ft m Carton Skid
1/2 12.78 2.44 32.0 14.5 50 40
M71A 3/32"10 3.05 40.0 18.1 50 40
5/8 15.98 2.44 32.0 14.5 50 4010 3.05 40.0 18.1 50 40
1/2 12.78 2.44 30.0 13.6 50 40
M81A 1/16"10 3.05 37.5 17.0 50 40
5/8 15.98 2.44 30.0 13.6 50 4010 3.05 37.5 17.0 50 40
Z71A* 3/32"1/2 12.7 10 3.05 28.0 12.7 50 405/8 15.9 10 3.05 35.0 15.8 50 40
Z81A* 1/16"1/2 12.7 10 3.05 26.0 11.8 50 405/8 15.9 10 3.05 32.5 14.7 50 40
*Zinc.
#701A Metal J-Trim with 3/32" (M71A, Z71A) and 1/16" Grounds (M81A, Z81A) Galvanized and Zinc
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:20 PM Page 206
207For more information or to contact a sales representative, see page 3
Veneer Beads and Trims#
701B Metal L-Trim
with 3/32" G
rounds (M71B/Z71B) and w
ith 1/16" Grounds (M
81B/Z81B)
For more information or to contact a sales representative, see page 3
Dietrich veneertrims M71B and M81B are L-shaped trimsdesigned for useat junctions ofveneer gypsumbase with roughconcrete ormasonry ceilings.Sized to fit 1/2"and 5/8" gypsumplaster base,M71B provides3/32" grounds fortwo-coat veneer,and M81B has
1/16" grounds for one-coat veneer plaster. Available instandard length of 8' and 10'.
Dietrich Z71B and Z81B veneer trims are the zinc equivalentsof M71B and M81B with the added benefit of providing ultimate corrosion protection for exteriorapplications. Available in standard length of 10'.
Applied after panel installation to finish veneer plasteredges at wall terminations.■ Mini-mesh flanges for keying.
■ Eliminates shadowing.
■ Galvanized coated or zinc for corrosion protection.
L-Trim
DMF Size Weight/Carton PackagingProduct Grounds Width Length lbs kg Pcs/ Carton/Code Inches mm ft m Carton Skid
1/2 12.78 2.44 32.0 14.5 50 60
M71B 3/32"10 3.05 40.0 18.1 50 60
5/8 15.98 2.44 32.0 14.5 50 6010 3.05 40.0 18.1 50 60
1/2 12.78 2.44 30.0 13.6 50 60
M81B 1/16"10 3.05 37.5 17.0 50 60
5/8 15.98 2.44 30.0 13.6 50 6010 3.05 37.5 17.0 50 60
Z71B* 3/32"1/2 12.7 10 3.05 28.0 12.7 50 605/8 15.9 10 3.05 35.0 15.8 50 60
Z81B* 1/16"1/2 12.7 10 3.05 26.0 11.8 50 605/8 15.9 10 3.05 32.5 14.7 50 60
*Zinc.
#701B Metal L-Trim with 3/32" (M71B, Z71B) and 1/16" Grounds (M81B, Z81B) Galvanized and Zinc
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:20 PM Page 207
208 The place to stop…before the building starts! SMrequest a quote online @
1A E
xpan
ded
Flan
ge C
orne
r Be
ad—
Gal
vani
zed
(CBX
A), Z
inc
(CBZ
A)
208 The place to stop…before the building starts! SMrequest a quote online @
Dietrich 1A expanded flange corner bead is used to providestrong corner reinforcement for conventional plasterapplications. A solid metal nose provides a straight, rigidground for screeding and the 2-7/8" or 3" flanges can beflexed easily over irregular, uneven surfaces. Plaster keysnear the solid nose provide increased reinforcement whereneeded and ensures straight corners. Available in 8' and 10'lengths in galvanized, and 10' lengths in zinc. Zinc isrecommended for interior high-moisture exposure areasand exterior plaster applications.
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Carton/Code Inches mm ft m Carton Skid
2-7/8 73.08 2.44 51.2 23.2 40 48
CBXA10 3.05 48.0 21.7 30 45
3 76.28 2.44 51.2 23.2 40 4810 3.05 48.0 21.7 30 45
CBZA*2-7/8 73.0 10 3.05 42.7 19.3 30 48
3 76.2 10 3.05 42.7 19.3 30 48
*Zinc.
1A Expanded Flange Corner Bead—Galvanized (CBXA), Zinc (CBZA)
Strong, expanded flange mesh cornerreinforcement for conventional plaster and fireproofing applications.■ Solid bead nose enhances rigidity and straight corners.
■ Preferred for irregular corners.
■ Easy to apply and finish.
Expanded Flange Corner Bead
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:20 PM Page 208
209For more information or to contact a sales representative, see page 3
Stucco and Plaster Casing BeadsD
ouble-X™
Corner Bead—
Galvanized (C
BXX)
For more information or to contact a sales representative, see page 3
Dietrich Double-X™ or 2A corner bead provides additionalrigidity for reinforcing plaster corners. Easily adjusts to setplaster depth on columns and is ideal for finishing corners ofstructural tile with rough masonry. Combination of expandedflanges and pronounced bead nose ensures effective corneralignment and efficient plaster keying from edge to nose.Manufactured with full 3-1/4" flanges and perforatedstiffening ribs.
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Carton/Code Inches mm ft m Carton SkidCBXX 3-1/4 82.6 10 3.05 76.0 34.4 30 25
Double-X™ Corner Bead—Galvanized (CBXX)
Wider flanges and perforated stiffening ribs provide superior corner reinforcement for plaster applications.■ Stiffening ribs along expanded flanges for additional rigidity.
■ Easy to apply and finish.
■ Effective corner alignment.
Double-X™
Corner Bead
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:20 PM Page 209
210 The place to stop…before the building starts! SMrequest a quote online @
Strip
Lat
h (L
AST)
Expanded metal strip for general plaster reinforcement.■ Finished edges for safe handling.
■ Galvanized for corrosion protection.
■ Easy to apply and finish.
Dietrich strip lath is a flat expanded metal strip used asplaster reinforcement over joints of non-metallic lathingbases and where dissimilar bases join. It’s commonlyattached diagonally at the corners of doors, windows orareas prone to cracks. May also be used to span pipe chasesor reinforce other stress points within the lath system.Available in 4" and 6" widths and 8' lengths.
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Carton/Code Inches mm ft m Carton SkidLAST 4 102 8 2.44 60.0 27.1 75 18LAST 6 152 8 2.44 78.0 35.3 75 18
Strip Lath (LAST)
210 The place to stop…before the building starts! SMrequest a quote online @
Strip Lath
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:20 PM Page 210
211For more information or to contact a sales representative, see page 3
Stucco and Plaster Casing Beads
Dietrich Cornerite™ reinforcing angle is used to reinforce all inside or inner plaster corners to reduce corner cracking.Cornerite™ reinforcing angle is formed from finished edgestrip lath and bent lengthwise to a 100° angle ensuring asnug fit into 90° corners. It’s commonly used when wallsmeet walls or ceilings, over inner angles of masonryconstruction and in the floating angle method of applyinggypsum lath to wood framing in order to reduce plastercracking.
Dietrich Cornerite™ reinforcing angle should be tied to thebase lath using 18-gauge tie wire. Cornerite™ should not beattached directly to support framing, but allowed to float in the corner. Available in 2" x 2" in 4' and 8' lengths, and 3" x 3" in 8' length only.
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Carton/Code Inches mm ft m Carton Skid
2 x 2 50.8 x 50.8 4 1.22 30 13.6 125 20XRIT 2 x 2 50.8 x 50.8 8 2.44 60 27.2 75 18
3 x 3 76.2 x 76.2 8 2.44 78 35.4 75 18
Cornerite™ Reinforcing Angle (XRIT)
Cornerite
™(XRIT)
For more information or to contact a sales representative, see page 3
Expanded metal lath angle for inside or inner plaster cornersand used to reduce corner cracks.■ Finished edges for safe handling.
■ Galvanized for corrosion protection.
■ Easy to apply and finish.
Cornerite™
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:20 PM Page 211
212 The place to stop…before the building starts! SMrequest a quote online @
#66
Exp
ande
d Fl
ange
Cas
ing
Bead
—G
alva
nize
d (X
XCB)
, Zin
c (X
XZB)
Universal plaster stop used at door and windowopenings, wall terminations and intersections.■ Used with stucco applications starting at 3/8” thick.
■ Available in galvanized and zinc for corrosionresistance.
■ Eliminates the need for expensive wood trims.
Dietrich #66expandedflange casingbeads are usedas a plasterstop, anexposed trimaround wallopenings andat junctions orintersectionsof plaster andother wall orceilingfinishes. Extra-
long expanded flange for tie-on applications. Short 90˚return flange at plaster surface ensures a neat finish.
Commonly applied under metal lath. Also used withgypsum lath, plaster board, plaster bases or masonryconstruction. #66 casing bead protects edges fromdamage, and covers shrinkage cracks that occur at stuccotermination within the lip of the bead.
DMF Size Weight/Carton PackagingProduct Grounds Length Weep Hole lbs kg Pcs/ Cartons/Code ft m Box Skid
3/8" 10 3.05 None 39.0 17.6 30 401/2" 10 3.05 None 42.0 19.0 30 405/8" 10 3.05 None 42.0 19.0 30 40
XXCB 3/4" 10 3.05 None 45.0 20.4 30 407/8" 10 3.05 None 48.0 21.7 30 401" 10 3.05 None 51.0 23.1 30 40
1-1/4" 10 3.05 None 54.0 24.4 30 403/8" 10 3.05 None 34.7 15.7 30 401/2" 10 3.05 None 37.3 16.9 30 405/8" 10 3.05 None 37.3 16.9 30 40
XXZB* 3/4" 10 3.05 None 40.0 18.1 30 407/8" 10 3.05 None 42.7 19.3 30 401" 10 3.05 None 45.3 20.5 30 40
1-1/4" 10 3.05 None 48.0 21.7 30 40
*Zinc.
#66 Expanded Flange Casing Bead—Galvanized (XXCB), Zinc (XXZB)
212 The place to stop…before the building starts! SMrequest a quote online @
#66 ExpandedFlange Casing Bead
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:20 PM Page 212
213For more information or to contact a sales representative, see page 3
Stucco and Plaster Casing Beads
DMF Size Weight/Carton PackagingProduct Grounds Length Weep Hole lbs kg Pcs/ Cartons/Code ft m Box Skid
3/8" 10 3.05 Yes 27.0 12.2 30 401/2" 10 3.05 Yes 30.0 13.6 30 405/8" 10 3.05 Yes 30.0 13.6 30 40
XXCW 3/4" 10 3.05 Yes 33.0 14.9 30 407/8" 10 3.05 Yes 33.0 14.9 30 401" 10 3.05 Yes 36.0 16.3 30 40
1-1/4" 10 3.05 Yes 39.0 17.6 30 403/8" 10 3.05 Yes 24.0 10.9 30 401/2" 10 3.05 Yes 26.7 12.1 30 405/8" 10 3.05 Yes 26.7 12.1 30 40
XXZW* 3/4" 10 3.05 Yes 29.3 13.3 30 407/8" 10 3.05 Yes 29.3 13.3 30 401" 10 3.05 Yes 32.0 14.5 30 40
1-1/4" 10 3.05 Yes 34.7 15.7 30 40
*Zinc.
Designed foruse with select,tested andapproved one-coat plastersystems, thisversion of the#66 ExpandedFlange CasingBead includesweep holes for moisturedissipation.Expandedflange is 3-1/8"
wide to aid plaster keying. NOTE: It is important toremember that casing beads with weep holes punched inthe ground flange are for tested and approved one-coatsystems. No other applications are implied or suggested.Available in galvanized steel or zinc. Zinc is recommended forexterior applications.
Casing or plaster stop with weep holes to allow waterdrainage in selected one-coat plaster systems.■ Available in galvanized and zinc.
■ Resists corrosion.
■ Easy to apply and finish.
#66 Expanded Flange C
asing Bead with W
eep Holes—
Galvanized (XXC
W), Zinc (XXZW
)
213For more information or to contact a sales representative, see page 3
#66 Expanded Flange Casing Bead with Weep Hole—Galvanized (XXCW), Zinc (XXZW)
#66 Casing Beadwith Weep Holes
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:20 PM Page 213
214 The place to stop…before the building starts! SMrequest a quote online @
#66
N S
hort
Flan
ge C
asin
g Be
ad—
Gal
vani
zed
(SFC
B), Z
inc
(SFZ
B)
Dietrich #66 N short flange casing beads are used asplaster stops, as exposed trim around wall openings andjunctions, or at intersections of plaster and other wall orceiling finishes. These casing beads are recommended forgypsum plaster bases. Perforated 1-1/4" nailing flange aidsattachment and plaster keying. Short flange 7/8" beads arerecommended when flange is applied under gypsum lathplaster base, and short flange 1/2" beads when flange isapplied over gypsum lath plaster base. Zinc isrecommended for exterior applications.
DMF Size Weight/Carton PackagingProduct Grounds Length Weep Hole lbs kg Pcs/ Cartons/ Code ft m Carton Skid
3/8" 10 3.05 No 33.0 14.9 30 301/2" 10 3.05 No 39.0 17.6 30 305/8" 10 3.05 No 39.0 17.6 30 30
SFCB 3/4" 10 3.05 No 42.0 19.0 30 307/8" 10 3.05 No 45.0 20.4 30 301" 10 3.05 No 48.0 21.7 30 30
1-1/4" 10 3.05 No 54.0 24.4 30 303/8" 10 3.05 No 29.3 13.3 30 30
SFZB*1/2" 10 3.05 No 34.7 15.7 30 303/4" 10 3.05 No 37.3 16.9 30 307/8" 10 3.05 No 40.0 18.1 30 30
*Zinc.
#66 N Short Flange Casing Bead—Galvanized (SFCB), Zinc (SFZB)
All-purpose solid flange casing plaster stop.■ Available in galvanized and zinc for corrosion resistance.
■ Eliminates the need for expensive wood trims.
214 The place to stop…before the building starts! SMrequest a quote online @
#66 N Short Flange Casing Bead
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:20 PM Page 214
215For more information or to contact a sales representative, see page 3
Stucco and Plaster Casing Beads
This Dietrich #66 N short flange casing bead has the sameuses as the #66 expanded flange casing beads associatedwith select one-coat systems but it has weep holes. The weepholes are added for moisture dissipation. Perforated 1-1/4"nailing flange aids attachment and plaster keying. NOTE: It isimportant to remember that casing beads with weepholes punched in the ground flange are for tested andapproved one-coat systems. No other applications are implied or suggested.
DMF Size Weight/Carton PackagingProduct Grounds Length Weep Hole lbs kg Pcs/ Cartons/Code ft m Carton Skid
3/8" 10 3.05 Yes 33.0 14.9 30 301/2" 10 3.05 Yes 39.0 17.6 30 305/8" 10 3.05 Yes 39.0 17.6 30 30
SFWB* 3/4" 10 3.05 Yes 42.0 19.0 30 307/8" 10 3.05 Yes 45.0 20.4 30 301" 10 3.05 Yes 48.0 21.7 30 30
1-1/4" 10 3.05 Yes 54.0 24.4 30 30
* Available in Zinc as a custom order.
Used with selected one-coat plaster systems. Weep holes for water drainage.■ Available in galvanized and zinc for corrosion resistance.
■ Easy to apply and finish.
#66 N
Short Flange Casing Bead w
ith Weep H
oles—G
alvanized (SFWB)
For more information or to contact a sales representative, see page 3
#66 N Short Flange CasingBead with Weep Holes
#66 N Short Flange Casing Bead with Weep Holes—Galvanized (SFWB)
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:20 PM Page 215
216 The place to stop…before the building starts! SMrequest a quote online @
Cor
ner
Mas
ter™
#30
(C
R30)
216 The place to stop…before the building starts! SMrequest a quote online @
Dietrich Corner Master™ #30 expansion/contractioncontrol joint is designed to provide stress relief at plasterwall inside corner intersections. The double-V expansionjoint absorbs movement due to expansion and contractionof plaster walls and controls cracking. Corner Master™ #30joint has expanded flanges preformed at 90˚ for a flush fitat inside corners. This expansion/control joint is offered inground heights of 1/2", 3/4" and 7/8", which aids plasterkeying and results in a clean, straight finish. Manufacturedfrom galvanized steel for corrosion protection.
CAUTION: Joints and corners are a potential point of water intrusion. Dietrich strongly recommendsbuilding paper be placed behind all joints and corners. Also, a bead of high-quality caulking shouldbe applied under the joints prior to the attachmentof the materials.
DMF Size Weight/Carton PackagingProduct Grounds Length lbs kg Pcs/ Carton/Code Inches mm ft m Carton Skid
1/2 12.7 10 3.05 42.5 19.2 24 30CR30 3/4 19.1 10 3.05 57.5 26.0 24 30
7/8 22.2 10 3.05 65.0 29.4 24 30
Corner Master™ #30 (CR30)
Proven expansion/contraction control for inside plaster corners.■ Provides reliable stress relief at inside corners.
■ Offers exacting grounds.
■ Available in galvanized.
Corner Master™
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:20 PM Page 216
217For more information or to contact a sales representative, see page 3
Stucco and Plaster Control JointsZinc C
ontrol Joints 38 (ZCJ3), 50 (ZC
J5), 75 (ZCJ7), 100 (ZC
J1)
For more information or to contact a sales representative, see page 3
Zinc Control Joints 38, 50, 75 and 100 are roll-formed from zinc to resist corrosion in both interior and exteriorapplications with gypsum or Portland cement plaster. An open slot, 1/4" wide and 1/2" deep, is protected with plastictape that is removed after plaster and finish is completed.Perforated short flanges aid keying and wire attachment to metal lath or stapling to gypsum lath. Effective plasterbonding is accomplished with the key-lock grounds. Groundheights come in 3/8" (38), 1/2" (50), 3/4" (75) and 1" (100).
NOTE: Should not be used with magnesium oxy-chloridecement stuccos or stuccos containing calcium chlorideadditives. Construction paper or felt strips should be usedas flashing behind all expansion joints.
CAUTION: Joints and corners are a potential point of water intrusion. Dietrich strongly recommends build-ing paper be placed behind all joints and corners. Also, a bead of high-quality caulking should be appliedunder the joints prior to the attachment of the materials.
Effectively accommodates movement at codeprescribed limits, reduces labor time andprovides a neat, finished appearance.■ Relieves stresses of expansion and contraction.
■ Maximum corrosion protection.
■ Provides effective plaster bond.
DMF Size Weight/Carton PackagingProduct Grounds Length lbs kg Pcs/ Carton/Code Inches mm ft m Carton SkidZCJ3 3/8 9.5 10 3.05 50.0 22.6 24 30ZCJ5 1/2 12.7 10 3.05 50.0 22.6 24 30ZCJ7 3/4 19.1 10 3.05 50.0 22.6 24 30ZCJ1 1 25.4 10 3.05 53.0 24.0 24 30
Zinc Control Joints 38(ZCJ3), 50 (ZCJ5), 75 (ZCJ7), 100 (ZCJ1)
Zinc Control Joint
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:20 PM Page 217
218 The place to stop…before the building starts! SMrequest a quote online @
Dou
ble-
V Ex
pans
ion
Con
trol J
oint
—G
alva
nize
d (V
VCJ)
, Zin
c (V
VZJ)
218 The place to stop…before the building starts! SMrequest a quote online @
Double-V Expansion Control Joints relieve the stresses of basic expansion andcontraction associated with inherent shrinkage during stucco curing and generalthermal changes. Expanded flanges allow for proper keying and easy installation.Corrosion protection maintained and ensured with galvanized steel and roll-formed zinc. Zinc is recommended for exterior applications. Ground heightsinclude 3/8" for thin coat plaster and 1/2", 3/4" and 7/8" for conventional plaster.
CAUTION: Joints and corners are a potential point of water intrusion.Dietrich strongly recommends building paper be placed behind all jointsand corners. Also, a bead of high-quality caulking should be applied underthe joints prior to the attachment of the materials.
DMF Size Weight/Carton PackagingProduct Grounds Length lbs kg Pcs/ Carton/Code Inches mm ft m Carton Skid
3/8 9.5 10 3.05 48 21.7 24 36
VVCJ1/2 12.7 10 3.05 67.0 30.3 24 363/4 19.1 10 3.05 74.0 33.5 24 307/8 22.2 10 3.05 67.0 30.3 24 301/2 12.7 10 3.05 59.6 27.0 24 36
VVZJ* 3/4 19.1 10 3.05 65.8 29.8 24 307/8 22.2 10 3.05 59.6 27.0 24 30
*Zinc.
Controls and reduces cracks that result from expansion and contraction in stucco applications.■ Relieves stresses of expansion and contraction.
■ Resists corrosion.
■ Controls and minimizes cracking.
■ Complies to ASTM C 1063.
Double-V Expansion Control Joint—Galvanized (VVCJ), Zinc (VVZJ)
Double-V ExpansionControl Joint
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:20 PM Page 218
219For more information or to contact a sales representative, see page 3
Stucco and Plaster Control JointsD
ouble-J Expansion Control Joint—
Galvanized (XJ15), Zinc (ZJ15)
For more information or to contact a sales representative, see page 3
A general-purpose control joint offering exceptional expansion control for plasteredwalls and ceilings, the Double-J Expansion Control Joint has a 5/16" reveal and rolledouter edges that allow effective plaster bonding. This helps prevent visible separationcracks. To ensure the desired finish, plaster must be embedded under rolled edgesand across the 1-1/4" expanded flanges. Plastic tape keeps the reveal clean and isremoved easily after finish application. Ground heights are 1/2", 3/4" and 7/8".Available in galvanized steel or zinc.
CAUTION: Joints and corners are a potential point of water intrusion. Dietrichstrongly recommends building paper be placed behind all joints and corners.Also, a bead of high-quality caulking should be applied under the joints prior to the attachment of the materials.
DMF Size Weight/Carton PackagingProduct Grounds Length lbs kg Pcs/ Carton/Code Inches mm ft m Carton Skid
1/2 12.7 10 3.05 38.4 17.4 24 40XJ15 3/4 19.1 10 3.05 43.0 19.5 24 40
7/8 22.2 10 3.05 45.6 20.6 24 401/2 12.7 10 3.05 34.1 15.4 24 40
ZJ15* 3/4 19.1 10 3.05 38.2 17.3 24 407/8 22.2 10 3.05 40.5 18.3 24 40
*Zinc.
Double-J Expansion Control Joint—Galvanized (XJ15), Zinc (ZJ15)
Rolled outer edges provide strong bond to stucco to preventseparation cracks.■ Exceptional expansion and contraction control.
■ Reduces stucco separation at joint edges.
■ Provides effective plaster bond.
■ Resists corrosion.
Double-J ExpansionControl Joint
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:20 PM Page 219
220 The place to stop…before the building starts! SMrequest a quote online @
Expa
nsio
n Jo
int #
40—
Gal
vani
zed
(EJ4
0), Z
inc
(EZ4
0)
220 The place to stop…before the building starts! SMrequest a quote online @
DMF Size Weight/Carton PackagingProduct Grounds Length lbs kg Pcs/ Carton/Code Inches mm ft m Carton Skid
1/2 12.7 10 3.05 41 18.3 15 42EJ40 3/4 19.1 10 3.05 44 19.7 15 42
7/8 22.2 10 3.05 45 20.4 15 421/2 12.7 10 3.05 50 22.4 15 42
EZ40* 3/4 19.1 10 3.05 53 23.8 15 427/8 22.2 10 3.05 56 25.1 15 42
Expansion Joint #40—Galvanized (EJ40), Zinc (EZ40)
Dietrich Expansion Joint #40 is a two-piece, slip joint thatfinishes butt ends of adjacent panels in wide or tall walls and ceilings to allow for multi-directional movement. Panelsare attached to parallel studs through the expansion jointflanges, enabling the finished surface to expand or contractnaturally without cracking. These are ideal for joiningdissimilar wall types such as wood framing to CMU and at construction joints.
Two-piece slip joint that accommodatesmovement in two directions.■ Allows for wall movement in multiple directions.
■ Adjusts from 1/4” to 5/8”.
■ Provides effective plaster bond.
■ Available with numerous modifications.Expansion Joint #40
#40 Expansion Joints should be used where excessivehorizontal and vertical movement may occur. They give better results than J-Trim when used as a feature strip or as a wall-to-ceiling joint. Atrium walls, wide wall areas andstructural column-through ceiling areas are some of their special applications. These offer broad functional and aesthetic opportunities. Adjustable expansion opening or reveal is 1/4" to 5/8". Ground heights are 1/2", 3/4" and 7/8".
CAUTION: Joints and corners are a potential point ofwater intrusion. Dietrich strongly recommends buildingpaper be placed behind all joints and corners. Also, abead of high-quality caulking should be applied underthe joints prior to the attachment of the materials.
*Zinc.
Caution: Additional weather shields should be installed behind the jointto enhance the weather resistance of this system.
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:20 PM Page 220
221For more information or to contact a sales representative, see page 3
Stucco, Screeds and Exterior Finishing ProductsF.H
.A.7. Foundation Weep Screed (FH
A7)
For more information or to contact a sales representative, see page 3
Dietrich F.H.A.7. foundation weep screed protects the stop edges of stucco and exterior insulated finish system materials at the sillplate. It’s commonly referred to as F.H.A. Screed because it meets all pertinent F.H.A. requirements as part of a drainage system forexterior stucco applications. The 3-1/2" nailing flange serves as a straight-edge stop at the sill plate line and flashing when water-resistant paper or paper-backed lath is installed over the flange.
The bottom of the vertical nailing flange must terminate at or below the bottom of the sill plate or the bottom of the shear panel.This will ensure a tight connection between the bottom flange of the weep screed and the foundation. Bonding holes are punchedin the 7/8" or 1-3/8" V-grounds to enable keying. The weeping occurs along the surface of the angular bead. Also available withoutbonding holes and in 28 gauge (FHAE) for non-code work.
The International Building Code (IBC)* requires that all foundation screeds have a 3-1/2" nailing flange, weep holes and aminimum thickness of 26-gauge steel.
DMF Size Weight/Carton PackagingProduct Grounds Depth Length lbs kg Pcs/ Pcs/Code Inches mm Inches mm ft m Carton Skid
FHA77/8 22.2 3-1/2 88.9 10 3.05 16.8 7.6 10 500
1-3/8 34.9 3-1/2 88.9 10 3.05 19.5 8.8 10 500
F.H.A.7 Foundation Weep Screed (FHA7)
Provides a screed and stucco stop at the sill plate line.■ Provides straight-edge stops for applied plaster stucco and E.I.F.S.
■ Offers exacting grounds and protective weeps.
■ Meets F.H.A. requirements.
■ Conforms to ASTM C 1063.
Foundation Weep Screed
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:20 PM Page 221
222 The place to stop…before the building starts! SMrequest a quote online @
7/8"
Sill
Scr
eed
(SI3
6)
222 The place to stop…before the building starts! SMrequest a quote online @
DMF Size Weight/Carton PackagingProduct Grounds Depth Length lbs kg Pcs/ Pcs/Code Inches mm Inches mm ft m Carton SkidSI36 7/8 22.2 5-1/2 139.7 10 3.05 3.3 1.5 10 500
7/8" Sill Screed (SI36)
Similar to the FHA7, but provides trowel accessunderneath to clean excess materialand trim vapor barrier.
*The International Building Code is published by the International Code Council, Inc.
Sill Screed
■ Provides straight-edge stops for applied plaster stucco and E.I.F.S.
■ Offers exacting grounds.
■ Impact and splash protection at bottom edge.
The SI36 is a similar profile to the FHA7 Foundation Screed except the bottom flange has been cut back to allow trowel access forcleaning excess material and trimming of the vapor barrier. The SI36 meets all other applicable codes with respect to 3-1/2" nailingflange, 26-gauge galvanized steel and 7/8" ground.
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:21 PM Page 222
223For more information or to contact a sales representative, see page 3
Stucco, Screeds and Exterior Finishing Products1-3/8" J-W
eep with 2" N
ailing Flange (JCLB), w
ith Weep H
oles (JWLB)
For more information or to contact a sales representative, see page 3
Dietrich 1-3/8" J-weep low-back is commonly used as a stop around door and window openings or in areas where stucco or E.I.F.S.terminations abut dissimilar wall types. Dietrich 1-3/8" J-weep low-back is nail, screw or staple-attached to the frame or sheathing,then foam insulation, cement board or metal lath can be installed over it. In any case, the protruding ridge of the metal must extendbeyond the plane of overlaid materials to serve as a ground for the stucco or E.I.F.S. application. Installed in conjunction with 1" rigidinsulation associated with one-coat plaster stucco systems, the 1-3/8" ground provides proper depth for plaster keying. Galvanized for corrosion protection, it also is available with weep holes ( JWLB).
1-3/8" J-Weep with a 2" nailing flange should not be used as a foundation weep screed for three-coat stucco applications. This casing or plaster stop bead should only be used on approved one-coat systems.
The International Building Code (IBC)* requires that all weep screeds have a 3-1/2" nailing flange, weep holes and a minimumthickness of 26-gauge steel. This product does not conform to code-required work if used as a foundation weep.
Used as a plaster or casing stop bead with stucco and E.I.F.S. Systems.■ Provides straight-edge stops for applied plaster stucco and E.I.F.S.
■ Used in conjunction with polystyrene or foam insulation board.
■ Offers exacting grounds and protective weeps.
■ Resists corrosion.
J Weep
DMF Size Weight PackagingProduct Grounds Depth Length lbs/ft kg/m Pcs/ Pcs/Code Inches mm Inches mm ft m Carton SkidJCLB 1-3/8 34.9 2 50.8 10 3.05 0.220 0.328 NA 500
JWLB** 1-3/8 34.9 2 50.8 10 3.05 0.220 0.328 NA 500
*The International Building Code is published by the International Code Council, Inc. **The JWLB product has weep holes.
1-3/8" J-Weep with 2" Nailing Flange (JCLB), with Weep Holes (JWLB)
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:21 PM Page 223
224 The place to stop…before the building starts! SMrequest a quote online @
J-W
eep
Hig
h-Ba
ck P
last
er S
top
(JW
P)
224 The place to stop…before the building starts! SMrequest a quote online @
DMF Size Weight/Carton PackagingProduct Grounds Depth Length lbs kg Pcs/ Pcs/Code Inches mm Inches mm ft m Carton Skid
JWP7/8 22.2 3-1/2 88.9 10 3.05 26.0 11.8 10 500
1-3/8 34.9 3-1/2 88.9 10 3.05 29.0 13.2 10 500
J-Weep High-Back Plaster Stop (JWP)
3-1/2" J-Weep High-Backused as sill weep screedor at door and windowopening■ Provides straight-edge stops for applied
plaster stucco and E.I.F.S.
■ Offers exacting grounds and protective weeps.
■ Resists corrosion.
*The International Building Code is published by the International Code Council, Inc.
J-Weep High-Back
Dietrich J-Weep high-back plaster stop is a J-shaped square-nosed trim manufactured from 26-gauge galvanized steel with7/8" or 1-3/8" grounds and 3-1/2" nailing flange. Punchedweep holes allow for use as a sill weep screed or screed andtrim around wall openings. Squared bends accommodate 1"rigid insulation and 3/8" one-coat stucco applications.
Dietrich J-Weep high-back ( JWP) meets the InternationalBuilding Code (IBC)* requirements that all foundation weepscreeds have a 3-1/2" minimum nailing flange, weep holesand a minimum thickness of 26-gauge steel.
1-3/8" J-Weep ( JCLB or JWLB) with a 2" nailing flange shouldnot be used as a foundation weep screed for three-coatstucco applications. This casing or plaster stop bead shouldonly be used on approved one-coat systems.
CAUTION: Joints and corners are a potential point ofwater intrusion. Dietrich strongly recommends buildingpaper be placed behind all joints and corners. Also, abead of high-quality caulking should be applied underthe joints prior to the attachment of the materials.
201-224 Veneer Stucco Plaster :DMF07_177 7/15/10 4:21 PM Page 224
225
Metal LathGalvanized Junior™ Mesh (LAM), (P), (O), (S) ..........................228Self-Furring Dimpled (LAD), (P), (O), (S) ..........................229Self-Furring V-Groove Mesh Lath (LAV), (P), (O), (S) ............................2304-Mesh 1/8" Z-Riblath (LAZ), (P) ..............................................2313/8" High Rib Lath (LAR)........................................................232Strip Lath (LAST) ................................233Cornerite™ (XRIT) ................................234Hanger Wire (HWB8, HWB9, HW12)....................235Tie Wire (TW18)..................................235Barrier Mesh (BM50), (BM75), (BM10), (BM15) ................................236
225-235 Metal Lath:DMF07_201 7/15/10 4:25 PM Page 225
Met
al L
ath
Ove
rvie
w
226 The place to stop…before the building starts! SMrequest a quote online @
METALLATH
OVERVIEWMetal lath and plaster systems havebeen used for many years in bothresidential and commercial appli-cations. Plaster finishes provide asmooth, high-quality wall surface,resistant to high impact and abra-sion. Metal lath is used as a substrateto create a strong mechanical bondwith plaster and stucco, and is usedon interior and exterior walls, ceil-ings, soffits, fascia and ceramic tileunderlayment.
Advantages
Strength—Metal lath embedded with the plaster provides superior strength and reinforcement.
Flexibility—Readily shaped to ornamental contours to a degree not possible withother plaster bases.
Fire Resistance—When used with gypsum plaster, metal lath provides excellent fire-resistant construction: up to two hours for partitions and four hours for ceilings andcolumn fireproofing.
Security—Metal lath and plaster surfaces are extremely difficult to penetrate. Theyprovide excellent protection against break-through.
Weight per Square YardMetal lath is commonly referred to in weight persquare yard. Each nominally sized 27" x 96" sheetequates to 2 square yards or 18 square feet persheet. Lath is available in three different weights:
1.75 lbs./sq. yd.—commonly used as an underlay-ment in interior ceramic tile applications and alsowith selected proprietary one-coat stucco systems.2.5 lbs./sq. yd.—commonly used as a substratefor ornamental and contour gypsum plaster orportland cement stucco.3.4 lbs./sq. yd.—commonly used for two- andthree-coat exterior stucco applications.NOTE: Not all weights are recommended for allapplications. Contact your Dietrich CustomerCare Representative for assistance.
Styles
Metal lath is available in a variety of differentstyles for various applications. Dietrich™ uses alettering system incorporated into the productcode to indicate available styles.
M—Flat Diamond Mesh
D—Dimpled Self Furring
V—V-Groove Self Furring
R—3/8" High Rib for Maximum Rigidity
225-235 Metal Lath:DMF07_201 7/15/10 4:25 PM Page 226
OverviewM
etal Lath Overview
227For more information or to contact a sales representative, see page 3
Paper-BackedOffset Options
Metal lath is availablebacked with asphalt sat-urated paper for appli-cations requiring amoisture barrier. Paperconforms to U.S.Federal SpecificationUU-B-790a, type 1,
grade D, style 2. Dietrich uses a lettering system incorporat-ed into the product code to indicate available offsets.
Types
Junior Diamond Mesh Lath is used as a substrate for gyp-sum plaster or for Portland cement plaster stucco on eitherinterior or exterior wall, ceiling, soffit and fascia surfaces, andcan be used under ceramic tile in wall ceiling and floor applica-tions. It’s useful in all general-purpose applications, and is thebest lath available for ornamental work and contoured surfaces.
Junior Diamond Mesh Lath—Asphalt Paper Backed isused in applications where a moisture barrier is required.Care should be taken to make sure paper overlaps paper andmetal overlaps metal in a shingle-like manner during appli-cation. Dietrich’s paper backing extends beyond the meshto accommodate shingling application. For external applica-tion, 3.4 lb./sq. yd. lath is recommended.
Self-Furring Junior Diamond Mesh Lath is attached tosubstrate through the dimple that furs the lath surface awayfrom a solid substrate. This lath is especially useful as a stuc-co base or for column fireproofing or replastering over oldsurfaces. Self-furred lath is required over all solid surfaces.
Self-Furring Junior Diamond Mesh Lath-AsphaltPaper Backed is used where a moisture barrier is required.It’s attached in the same manner, but care should be takento make sure paper overlaps paper during application.
3/8" Riblath is the most rigid of all and provides the addedsupport required when framing is more than 16" O.C. butless than or equal to 24" O.C. In wall and ceiling applications,it must be attached in the same manner as 4-Mesh Riblath.Due to 3/8" rib, minimum ground thickness must be 1".
Barrier Mesh is a tough, rigid heavy-gauge expanded meshused behind common wall substrates to protect against break-ins and break-outs. This high-strength security mesh is tough tosmash or cut and safeguards walls and ceilings in homes, apart-ments, offices, stores, storage areas and correctional facilities.
Installation
Lath should be applied with the longdimension across supports and with endjoints staggered between courses. Theends of the mesh lath should be lapped 1",and the sides should be lapped at least1/2". Check lap minimums required bylocal code. Nail, screw or staple-attachmesh lath on walls, so that the lower sheetsoverlap the upper sheets. Lath also may bewire tied to the furring channel for ceilingapplications. If an end lap should occurbetween supports, the two sheets should
be laced or tied using 18-gauge tie wire. Secure lath to all sup-ports at intervals not exceeding 6". Mesh lath should beformed into corners and carried out onto an abutting surface.Where this is not possible, Cornerite™, an internal plasterangle reinforcement should be used.
Paper-Back Installation
Installation of paper-backed lath is best accomplished whenmetal-to-metal and paper-to-paper contact is maintained.Dietrich Metal Framing uses asphalt-saturated paper meet-ing U.S. Federal Spec. UU-B-790a as backing on metal lathproducts. This paper provides a water- resistant barrier thatis a vapor-permeable backing consistent with grade D, style2 paper (other grades and styles are available upon request).Minimum lap requirement for Jr. Diamond Mesh, Self-Furring can be easily attained with “P” (paper offset 1" onone side and one end). ASTM C-1063, requires a 2" mini-mum paper lap on all sides. Dietrich’s paper offset option“O” conforms to this specification. Make sure to consultyour local building code to ensure proper compliance.
*Available for non-code work. The International BuildingCode (IBC) requires a 2" paper lap per ASTM C 1063-99.
P—Paper is offset by 1" on one sideand one end.*
O—Paper is offset by 2" on one sideand one end.
225-235 Metal Lath:DMF07_201 7/15/10 4:25 PM Page 227
Gal
vani
zed
Juni
or™
Mes
h (L
AM),
(P)
, (O
)
Dietrich Junior™ diamond mesh lath is used as a substrate forgypsum plaster or for Portland cement plaster stucco oneither interior or exterior walls, ceilings, soffit and fasciasurfaces, and can be used under ceramic tile in wall, ceilingand floor applications. It’s useful in all general-purposeapplications and is the best lath available for ornamentalwork and contoured surfaces.
Galvanized steel sheets are slit and expanded to form smalldiamond mesh openings (over 11,000 per square yard).This large number of openings provides superior stucco
bonding. Diamond mesh lath is easily cut and can beformed to accommodate curved surfaces includingornamental, contour plastering. All sheets are flat 27" x 96"(nominal) rectangles with squared ends and smooth edgesthat allow for efficient installation and consistent lapping.
*Asphalt paper-backed lath is available in a variety of offsetsfor various applications requiring a moisture barrier. Paperconforms to Federal Specification UU-B-790A; type 1, gradeD, style 2 and type 1, grade B, style 1a.
Paper-Backed Offset Options
P — Paper is offset by 1" on one side and one end. +O — Paper is offset by 2" on one side and one end.
+Available for non-code work. The International BuildingCode (IBC) requires a 2" paper lap per ASTM C 1063-06.
Limitations: Metal lath products should not be usedwith magnesium oxychloride cement stuccos or stuccoscontaining calcium chloride additives. In ceilingassemblies, certain precautions concerningconstruction, insulation and ventilation are necessaryfor good performance.
General-purpose lathprovides an exceptionallystrong substrate forgypsum plaster andPortland cement plaster stucco.■ Excellent for ornamental and contour
plastering.
■ Small mesh openings conserve plaster and reduce droppings.
■ Minimizes stress cracks by maintainingconsistent plaster depths.
■ Available in 1.75, 2.5 and 3.4 pounds persquare yard.
228 The place to stop…before the building starts! SMrequest a quote online @
Junior™ Mesh
DMF Weight Size PackagingProduct lbs/yard2 kg/m2 Width Length Pcs/ Bundles/ Yds2/ m2/Code Inches mm Inches mm Bundle Skid Skid Skid
LAM 1.75 1.0 27 686 96 2438 10 50 1000 836
(P, O)2.5 1.4 27 686 96 2438 10 50 1000 8363.4 1.8 27 686 96 2438 10 50 1000 836
Galvanized Junior™ Mesh (LAM), (P), (O)
225-235 Metal Lath:DMF07_201 7/15/10 4:25 PM Page 228
Metal Lath
Dietrich self-furring dimpled lath is manufactured withapproximately 1/4" deep dimples that raises diamond meshaway from solid surfaces to enable thorough plaster orstucco penetration into and behind the lath for superiormechanical bonding. The approximately 1/4" dimples arespaced every 1-1/2" O.C. over the entire 27" x 96" rectangularsheet. This pattern, with approximately 11,000 keys persquare yard, serves to hold lath approximately 1/4" awayfrom the surface, enabling the plaster to penetrate fully andbond over solid surfaces like concrete, cement board,column fireproofing, masonry and replastering over oldsurfaces. To maintain the designed furring characteristics,fasteners must be applied within the dimple cavity.
Dimpled Lath is also available with an asphalt paper-backing for applications that require a moisture barrier. The glue-attached asphalt-saturated building paper also ensures aconsistent plaster or stucco depth as the paper preventsexcessive plaster waste and stucco thickness variation. Careshould be taken to make sure paper overlaps paper in ashingle-like manner during application.
Dimpled raised lath substrate for superior mechanicalbond over solid surfaces.■ Dimples ensure thorough plaster penetration
and strong mechanical bond.
■ Easily shaped for curved or contoured surfaces.
■ Maintains consistent plaster depths.
Paper-Backed Offset Options
P — Paper is offset by 1" on one side and one end. +O — Paper is offset by 2" on one side and one end.
+Available for non-code work. The International BuildingCode (IBC) requires a 2" paper lap per ASTM C 1063-06.
Self-Furring Dim
pled (LAD), (P), (O
)
229For more information or to contact a sales representative, see page 3
Self-Furring Dimpled
DMF Weight Size PackagingProduct lbs/yard2 kg/m2 Width Length Pcs/ Bundles/ Yds2/ m2/Code Inches mm Inches mm Bundle Skid Skid Skid
LAD1.75 1.0 27 686 96 2438 10 25 500 418
(P, O)2.5 1.4 27 686 96 2438 10 25 500 4183.4 1.8 27 686 96 2438 10 25 500 418
Self-Furring Dimpled (LAD), (P), (O)
225-235 Metal Lath:DMF07_201 7/15/10 4:25 PM Page 229
Self-
Furri
ng V
-Gro
ove
Mes
h La
th (
LAV)
, (P)
, (O
)
Dietrich self-furring v-groove mesh lath is manufacturedwith five approximately 1/4" deep "V" ribs along the lengthof the sheet. These Vs raise the diamond mesh from solidsurfaces to allow thorough plaster or stucco penetrationinto and behind the lath for superior mechanical bonding.V-Groove is used over solid surfaces like concrete, cementboard, column fireproofing, masonry, sheathing andreplastering over old surfaces. To maintain the designed V-groove furring characteristics, fasteners must be appliedwithin the V-cavity.
V-Groove is also available with asphaltpaper-backed for applications thatrequire a moisture barrier. The glue-attached asphalt-saturated paper alsoensures a consistent plaster or stuccodepth as the paper prevents excessiveplaster waste. Care should be taken tomake sure paper overlaps paper in ashingle-like manner during application.
Paper-Backed Offset Options
P — Paper is offset by 1" on one side and one end. +
O — Paper is offset by 2" on one side and one end.
+Available for non-code work. TheInternational Building Code (IBC)requires a 2" paper lap per ASTM C1063-06.
V-Groove raises lath substratefor strong mechanical bondover solid surfaces.■ V-Grooves provide space for full plaster key
into mesh.
■ Maintains consistent plaster depths.
■ Eliminates need for added furring strips.
■ Available in 1.75, 2.5 and 3.4 lbs. per square yard.
230 The place to stop…before the building starts! SMrequest a quote online @
Self-Furring, V-Groove
DMF Weight Size PackagingProduct lbs/yard2 kg/m2 Width Length Pcs/ Bundles/ Yards2/ m2/Code Inches mm Inches mm Bundle Skid Skid Skid
LAV 1.75 1.0 27 686 96 2438 10 25 500 418
(P, O)2.5 1.4 27 686 96 2438 10 25 500 4183.4 1.8 27 686 96 2438 10 25 500 418
Self-Furring V-Groove Mesh Lath (LAV), (P), (O)
225-235 Metal Lath:DMF07_201 7/15/10 4:25 PM Page 230
Metal Lath3/8" H
igh Rib Lath (LAR)
231For more information or to contact a sales representative, see page 3
Designed to provideexceptional rigidityin ceiling and soffitapplications.■ Herringbone mesh pattern allows
for excellent keying.
■ Commonly used for plaster ceilingsunder steel joists, concrete floorsand over soffits.
■ Easily lapped at outer edgesreducing plaster cracks.
■ Available in 3.4 lbs. per squareyard only.
■ Not suitable for contour plastering.
3/8" High Rib Lath
Dietrich 3/8" High Rib Lath is the most rigid of all laths andprovides the added support required when framing is morethan 16" O.C. but does not exceed 24" O.C. It is commonlyused for soffits and ceilings under steel or wood joistconstruction and metal-reinforced concrete floors.
Dietrich 3/8" High Rib Lath has a herringbone meshpattern with 3/8" V-shaped ribs running the length of thesheet at 3-7/8" intervals and inverted 3/16" intermediateribs. The rib is placed against the framing member anddoes not require a minimum 1" three-coat system.
Because of the Dietrich 3/8" riblath’s extraordinarystrength, this lath can be used for studless nonload-bearingpartitions by wire tying lath back to back with ribs runningperpendicular to each other. Plaster can then be applied to form a wall 2" thick.
DMF Weight Size PackagingProduct lbs/yard2 kg/m2 Width Length Pcs/ Bundles/ Yards2/ m2/Code Inches mm Inches mm Bundle Skid Skid SkidLAR 3.4 1.8 27 686 96 2438 10 50 1000 836
3/8" High Rib Lath (LAR)
225-235 Metal Lath:DMF07_201 7/15/10 4:25 PM Page 231
Strip
Lat
h (L
AST)
Dietrich Strip Lath is a flat expanded metal strip used as plasterreinforcement over joints of non-metallic lathing bases and wheredissimilar bases join. It’s commonly attached diagonally at the corners ofdoors, windows or areas prone to cracks. It may also be used to span pipechases or reinforce other stress points such as the corners of openings inthe stucco membrane within the lath system. Available in 4" and 6" widthsand 8' lengths.
Expanded metal stripfor general plasterreinforcement.■ Finished edges for safe handling.
■ Galvanized for corrosion protection.
■ Easy to apply and finish.
232 The place to stop…before the building starts! SMrequest a quote online @
Strip Lath
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Pcs/Code Inches mm ft m Bundle Skid
LAST4 102 8 2.44 24.5 11.1 75 13506 152 8 2.44 35.8 16.2 75 1350
Strip Lath (LAST)
225-235 Metal Lath:DMF07_201 7/15/10 4:26 PM Page 232
Metal LathC
ornerite™
(XRIT)
233For more information or to contact a sales representative, see page 3
Dietrich Cornerite™ metal lath angle is used to reinforce allinside or inner plaster corners to reduce corner cracking.Cornerite™ metal lath angle is formed from finished edgestrip lath and bent lengthwise to a 100° angle to ensure asnug fit into 90° corners. It's commonly used when wallsmeet walls or ceilings, over inner angles of masonryconstruction and in the floating-angle method of applyinggypsum lath to wood framing in order to reduce plastercracking.
Dietrich Cornerite™ metal lath angle should be tied to thebase lath using 18-gauge tie wire. Cornerite™ metal lathangle should not be attached directly to support framingbut allowed to float in the corner. Available in 2" x 2" in 4 'and 8' lengths, and 3" x 3" in 8' lengths only.
DMF Size Weight/Carton PackagingProduct Width Length lbs kg Pcs/ Pcs/Code Inches mm ft m Bundle Skid
2 x 2 50.8 x 50.8 4 1.22 30 13.6 125 1350XRIT 2 x 2 50.8 x 50.8 8 2.44 60 27.2 75 1350
3 x 3 50.8 x 50.8 8 2.44 78 35.4 75 1350
Cornerite™ (XRIT)
Expanded metal lath angle for inside or inner plastercorners used to reduce corner cracks.■ Finished edges for safe handling.
■ Galvanized for corrosion protection.
■ Easy to apply and finish.
Cornerite™
225-235 Metal Lath:DMF07_201 7/15/10 4:26 PM Page 233
Han
ger
Wire
(H
WB8
, HW
B9, H
W12
) &
Tie
Wire
(TW
18)
234 The place to stop…before the building starts! SMrequest a quote online @
Dietrich hanger wire is available in 8, 9 and 12 gauge and isgalvanized for corrosion resistance. Hanger wire issuspended from the underside of the floor structure toprovide a structural support for drop, gypsum wallboard orplaster suspended ceilings.
Dietrich tie wire is 18-gauge galvanized soft annealed wireused in drywall and plaster construction to tie furringchannels to main runner U-channels. It’s also used to tiemetal lath to channels in plaster construction, attachexpansion/control joints to lath and tie the lath overlapbetween rows of fasteners.
Suspends and connects U-channeland furring channel gridwork fordrywall, plaster and veneer ceilings.■ Tie wire is available in 18 gauge and in lengths of 24”, 28” and 48”.
■ Hanger wire is available in 8, 9 and 12 gauge and lengths of 12’.
■ Wire products conform to ASTM C 1063 and A 641.
■ Available by the hank (bundle).
DMF Length Weight/Bundle PackagingProduct Gauge ft m lbs kg Bundles/Code SkidHWB8 8 12 3.66 50 22.62 20HWB9 9 12 3.66 50 22.62 20HW12 12 12 3.66 50 22.62 20
Hanger Wire (HWB8, HWB9, HW12)
DMF Length Weight/BoxProduct Gauge Inches mm lbs kgCode
24 610 25 11.31TW18 18 28 711 25 11.31
48 1219 50 22.62
Tie Wire (TW18)
Hanger Wire
Tie Wire
Hanger Wire Tie Wire
225-235 Metal Lath:DMF07_201 7/15/10 4:26 PM Page 234
Metal LathBarrier M
esh BM
50, BM
75, BM
10, BM
15
235For more information or to contact a sales representative, see page 3
*Available in standard or flat.
BM50 BM15
DMF Thickness Size Weight SWD LWD C-C of Bond Percent of OverallProduct Gauge Inches mm lbs/100 ft2 kg/m2 Width Length (SWD x LWD) Open Area ThicknessCode
18 1/2 12.7 66 3.21 96" 48" .500" x 1.20" 60 .039"BM50 16 1/2 12.7 82 3.99 96" 48" .500" x 1.20" 63 .050"
13 1/2 12.7 140 6.82 96" 48" .500" x 1.20" 52 .070"
BM75 13 3/4 19.1 75 3.65 96" 48" .923" x 2.00" 74 .070"10 3/4 19.1 171 8.33 96" 48" .923" x 2.00" 63 .120"
BM10 16 1 25.4 41 2.00 96" 48" 1.090" x 2.00" 78 .050"16 1-1/2 38.1 38 1.85 96" 48" 1.33" x 3.00" 83 .048"
BM15 13 1-1/2 38.1 57 2.78 96" 48" 1.33" x 3.00" 80 .070"10 1-1/2 38.1 114 5.55 96" 48" 1.33" x 3.00" 75 .110"
Barrier Mesh (BM50), (BM75), (BM10), (BM15)
Barrier Mesh is a tough, rigid heavy-gauge security mesh used behindcommon-wall substrates to protect against break-ins and break-outs. Sheetsare 48" x 96" expanded steel used to provide continuous reinforcement wheresecurity is the objective. This high-strength security mesh is tough to smash orcut and safeguards walls and ceilings in homes, apartments, offices, stores,vaults, storage areas and correctional facilities.
In addition to providing a high-strength and fire-resistant plaster finish, BarrierMesh also offers a cost-effective and time-saving alternative to reinforcedconcrete or concrete block. Available opening widths include: 1/2" (BM50),3/4" (BM75), 1" (BM10) and 1-1/2" (BM15). Available gauges include: 18 gauge(BM50); 16 gauge (BM50), (BM10), (BM15); 13 gauge (BM50), (BM75),(BM15) and 10 gauge (BM75), (BM15). Product can be produced to MilitarySpec. MIL-M-17194 Type II, Class 1; ASTM 1267. Special order gauge andlength combinations can be provided upon request. Inquire with yourDietrich Metal Framing Customer Care Representative.
High-strength security backingfor walls and ceilings in alltypes of construction.■ Protects against break-ins and break-outs.
■ Ideal for use in lieu of reinforced concrete orconcrete block.
■ High-strength and fire-resistant.
■ Made from carbon steel.
■ Also available in galvanized steel.
225-235 Metal Lath_DMF07_201 9/28/10 10:31 AM Page 235
Inde
x
236 The place to stop…before the building starts! SMrequest a quote online @
#30 Corner Master™ ....................................................216#40 Expansion Joint ....................................................221#66 Expanded Flange Casing Bead ....................212–213#66 N Short Flange Casing Bead ......................214–215#7 Foundation Weep Screed ......................................222#701A Metal J-Trim with 3/32" Grounds ....................206#701B Metal L-Trim with 3/32" Grounds ....................207#801A Metal J-Trim with 1/16" Grounds ....................206#801B Metal L-Trim with 1/16" Grounds ....................207093 Control Joint ........................................170, 186, 205103 Deluxe®....................................................................12103 Deluxe® Corner Bead ............................................152135 Corner Angle ..........................................................501-3/8" J-Weep ............................................................2231-A Expanded Flange Corner Bead ............................2082-Piece Expansion Joint #40 ......................................2212-Way Corner Cap — 3/4" Bullnose ..........................1802-Way Corner Cap — Metal ......................................1583-Way Corner Cap — 3/4" Bullnose ..........................1803-Way Corner Cap — Metal ........................................1583-Way Off-Angle Overlap Corner Cap —
1-1/2" Bullnose ....................................................1823-Way Off-Angle Overlap Corner Cap —
3/4" Bullnose ......................................................1823-Way Overlap Corner Cap — 1-1/2" Bullnose ........1813-Way Overlap Corner Cap — 3/4" Bullnose..............1813/8" High Rib Lath ......................................................2315-1/2" Sill Screed ........................................................2225400 Spazzer™ ..............................................................125400 Spazzer® Bar ..................................................68, 90800 Mini-Bead™ ..........................................................172900 Mini-Bead™ ..........................................................1729200 Spazzer™ ..............................................................129200 Spazzer® Bar ..................................................43, 46
■ ■ ■ ■ ■ A ■ ■ ■ ■ ■
A-Series™ Support Clip ................................................104Accelerated Building Technologies ..............................13Adjustable Expansion Joint #40 ................................221AEC Support ..................................................................18AEGIS Metal Framing ....................................................13AEGIS™ Trusses....................................................138–139Aluminum Breakaway Clips ........................................147ArchWay Corner Bead ................................................177Area-Separation Walls..........................................146–147Asphalt-Backed Metal Lath ................................226–230ASTM ..............................................................4, 242–243
■ ■ ■ ■ ■ B ■ ■ ■ ■ ■
B-Series™ Support Clips ..............................................102Back-to-Back Headers ................................................90Backing Plate ....................................................54–55, 57Bar Guard ....................................................................106Barrier Mesh ..............................................................235Benefits of Steel ........................................................8–11Benefits of UltraSTEEL® ..........................................24–25Block & Strap ........................................................41, 109Boxed Headers ............................................................75Breakaway Clips ........................................................147Break Press..................................................................114Bridging Bar ..................................................................46Bridging/Bracing — Drywall ....................................46–47Bridging/Bracing — Structural ............................106–111Bridle Hanger ..............................................................130Bullnose Cornerbead
Bullnose “J” Round — Metal ..............................157Bullnose 135 Degree — Metal ............................155Bullnose 90 Degree — Metal ..............................154Bullnose Corner Bead — Metal ..................154–157Bullnose Corner Bead — Paper-Faced ......194–197Bullnose Corner Bead — Vinyl ....................178–179Bullnose Half Round — Metal ............................157Bullnose Kerf — Metal ........................................156Bullnose Splayed — Metal ..................................155
Bullnose Corner & Transition Caps2-Way Metal Corner Cap ....................................1583-Way Metal Corner Cap ....................................1582-Way 90˚ Inside Corner Cap
(3/4" Bullnose) — Vinyl ................................1803-Way 90˚ Overlap Corner Cap
(3/4" Bullnose) — Vinyl ................................1803-Way 90˚ Corner Cap (3/4" Bullnose) — Vinyl ..1813-Way 90˚ Overlap Corner Cap
(1-1/2" Bullnose) — Vinyl ............................1813-Way Off-Angle Overlap Corner Cap
(3/4" Bullnose) — Vinyl ................................1823-Way Off-Angle Overlap Corner Cap
(1-1/2" Bullnose) — Vinyl ............................182Transition Cap (Bullnose to 90˚) ..........................159
236-244 Index Pages:DMF07_212-217_Index 7/15/10 4:53 PM Page 236
Index
237For more information or to contact a sales representative, see page 3
■ ■ ■ ■ ■ C ■ ■ ■ ■ ■
C-Joist ..............................................................118–119C-Runner — Area Separation System ........................146C-Stud Headers ......................................................90–91C-Studs ..................................................................62–64C-Stud Trusses ..........................................................140CAD Details ..........................................inside back coverCapped Headers ..........................................................91Casing Bead ........................................................212–215Cavity Shaft Wall ..................................................144–145Ceilings — Furring & CRC Application ..................48–49Certification Letter................................................242–245Clinch-On Products, Co.’s Corner Beads
Corner Bead/Electro ............................................160Corner Bead/Hot-Dipped Galvanized ................161Corner Bead/Smooth ..........................................162Corner Splay — Hot-Dipped ..............................163Corner Splay — Electro ......................................163Electro Bullnose ..................................................164Hot Dipped Bullnose ..........................................164Electro Bullnose Splay ........................................165Hot Dipped 3/4" Bullnose Splay ..........................165Painted 3/4" Bullnose ..........................................167Painted 3/4" Bullnose Splayed ............................165
Clinch Tool ..................................................................152Clip Angles ..........................................................100–104Clip ExpressSM ..........................................................12, 14Coatings ..................................................................4, 244Cold-Rolled Channel ............................................47, 107Composite Limiting Heights ....................................28–33Contour Track® ........................................................38–39Control Joints ..............................................163, 217–221Corner Angle ........................................................50, 112Corner Beads
Corner Bead Electro ............................................152Corner Beads — Metal ................................152–157Corner Beads — Paper-Faced ....................190–198Corner Beads — Vinyl ................................176–179
Cornerbead Tool ..........................................................152Corner Master™ #30 ....................................................216Cornerite™ ..........................................................211, 233Cost ................................................................................9CRC ......................................................................47, 107CSE™ ..............................................................62–63, 118CSJ™ ..............................................................62–63, 118CSS™ ..............................................................62–63, 118CSW™ ..............................................................62–63, 118C-Stud Trusses ..........................................................140CT Studs ....................................................................144
Curtain-Wall Studs ..................................................62–63Custom Brakes, Shapes & Miscellaneous Angles ......114Customer Care ..............................................................17Customer Service ..........................................................16CWI™ ......................................................................62–63CWN™ ....................................................................62–63
■ ■ ■ ■ ■ D ■ ■ ■ ■ ■
Danback™ ..........................................................12, 54–55DDG ..................................................................13, 19, 35Deep-V E.I.F.S. Expansion Joint ................................212Deflection Connectors/Accessories ........................92–98Deflection Track Systems — Drywall ................40, 42–45Deflection Track Systems — Structural ..................66–71D.E.F.S. ......................................................................175Deluxe Cornerbead......................................................152Diagonal Tension Strap ..............................................110Diamond Mesh Lath ....................................................228Dietrich Clip ExpressSM ............................................12, 14Dietrich Design Group....................................................13Dimpled Self-Furring Lath ..........................................229Double-J Expansion Joint — Galvanized ..................219Double Leg Resilient Channel........................................52DoubleTrack™ — Drywall ..............................................45DoubleTrack™ — Structural ....................................70–71Double-V Expansion Control Joint ..............................218Double-X™ Corner Bead ..............................................209Drywall Beads & Trims ........................................152–200Drywall Furring Channel ................................................51Drywall Knockouts ........................................................27Drywall Studs ................................................................26Drywall Track ..........................................................36–37Dull Corner Bead ........................................................152DWC ..............................................................................51
■ ■ ■ ■ ■ E ■ ■ ■ ■ ■
E-Business ....................................................................16E-Stud ..........................................................................145Earthquakes ..................................................................10EasyClip™ Support Clips ........................................99–104E-Series™ Support Clip ..........................................99, 124E.I.F.S. ........................................................................167End Clips (A-Series™) ..................................................104Environmental Benefits ..................................................11Expansion Joint #40 ..................................................220Extended Fast Clip ........................................................93Exterior Light-Gauge Load-Bearing Headers ..........88–91
236-244 Index Pages:DMF07_212-217_Index 7/15/10 4:53 PM Page 237
Inde
x
238 The place to stop…before the building starts! SMrequest a quote online @
Exterior Finish Systems AccessoriesMini-Bead™ 800 & Mini-Bead™ 900 Zinc ..............204J-Trim 701-A Zinc ................................................206L-Trim 701-B Zinc ................................................207Zinc Control Joint 38, 50, 75 & 100 ....................217Double-V Expansion Control Joint Zinc ..............218Double-J Expansion Control Joint Zinc ..............219Expansion Joint #40 Zinc ....................................2211A Expanded Flange Corner Bead Zinc ..............208
Exterior Framing ....................................................59–114
■ ■ ■ ■ ■ F ■ ■ ■ ■ ■
F.H.A.7 Foundation Screed ........................................221Fast Clip™ ......................................................................92Fast Strut™ ..............................................................12, 95Fast Top™ Clip ........................................................12, 94Fire-Rated Assemblies ..................................34, 141–148Fire Resistance ................................................................9Fire Wall ..............................................................144–147Flat Strap........................................................................57Floor Framing ......................................................115–134Floor Joist Framing Components ......................118–134Floor Joist Hangers & Connectors ......................128–134Foundation Clips ........................................................134Foundation Screeds ............................................222–224Furring Channel — Heavy-Duty ..................................113Furring Channel ............................................................47Furring Channel Clips ..................................................49
■ ■ ■ ■ ■ G ■ ■ ■ ■ ■
Gauges ............................................................................5Galvanized Junior Mesh ............................................228General Notes ..................................................................5Goldline® ........................................................................12Grabber® ........................................................................12Green Building ............................................................244Grommets/Insulators ............................................52, 121Grooved Self-Furring Mesh Lath ................................230Gussett Plates ............................................................111
■ ■ ■ ■ ■ H ■ ■ ■ ■ ■
Hanger Wire ....................................................48–49, 234Hat Channel ..................................................................51Head of Wall ........................................42–45, 66–71, 148Heavy-Duty Furring Channel........................................113Headers ..................................................................88–91High Hat Channel ..........................................................51
Horizontal Bracing ............................................54–55, 57Hot-Dipped Galvanized Corner Bead ........................153H-Stud ......................................................................147H-Track ......................................................................146Hurricanes ....................................................................10Hurricane Ties ..............................................................140
■ ■ ■ ■ ■ I ■ ■ ■ ■ ■
I-Headers ......................................................................90ICC ......................................................inside back coverICF Hanger ..................................................................131Installation Assistance ..........................inside back coverInterior Deflection Systems................................40, 42–45Interior Framing ........................................................21–58Interior Framing-Ceilings..........................................48–49International ..................................................................20
■ ■ ■ ■ ■ J ■ ■ ■ ■ ■
J-Bead — Vinyl ..........................................................184“J” Round ..................................................................157J-Tabbed Track ..........................................................145J-Trim — Metal ..........................................................168J-Weep Plaster Stop ..........................................223–224Jamb Strut ..................................................................145Joists, Steel..........................................................118–123Joist Hangers ......................................................129–131Junior Diamond Mesh....................................................12Junior™ Mesh................................................................228
■ ■ ■ ■ ■ K ■ ■ ■ ■ ■
K-Bead ......................................................................172Kal Korner® Bead ........................................................172Keene™ ........................................................................12Kerfed Bullnose ..................................................156, 179Knockouts ..............................................................27, 64Knockouts Drywall ........................................................27KSI ..........................................................................4, 243
■ ■ ■ ■ ■ L ■ ■ ■ ■ ■
L-Header ......................................................................88L-Trim — Metal ..........................................................170L-Stop Bead — Vinyl ..................................................185L-Angle ..................................................................50, 112Lateral Tie Plate ..........................................................133Ledger Connector System ..........................................131LEED® Credits ..............................................................244Light-Gauge Structural Framing Systems ..............62–65
236-244 Index Pages:DMF07_212-217_Index 7/15/10 4:53 PM Page 238
Index
239For more information or to contact a sales representative, see page 3
Light-Gauge Structural Track ........................................65Lightning ........................................................................10Limiting Heights ......................................................28–33Limiting Heights — Drywall......................................28–33Locations ........................................................................3Long-Leg Track — Drywall ....................................36–37Long-Leg Track — Structural ......................................65Lox Drive® ......................................................................12
■ ■ ■ ■ ■ M ■ ■ ■ ■ ■
Material Certification ............................................234–235Mesh Lath ....................................................................220Metal Angle Runner ..............................................50, 112Metal Beads & Trims
103 Deluxe® Corner Bead ....................................152120/135˚ Corner Bead ........................................153135˚ Bullnose Corner Bead ................................1553/4" Bullnose 2-Way Corner Cap ........................1583/4" Bullnose 3-Way Corner Cap ........................15890˚ Bullnose Corner Bead ..................................154Bullnose “J” Round ............................................157Bullnose Kerfed Corner Bead ..............................156J-Trim ..................................................................168L-Trim ..................................................................170Quicksilver™ Corner Bead ....................................153Splayed Bullnose ................................................155U-Trim ..................................................................169
Metal Trims & Finishing Products093 Drywall Control Joint ....................................171J-Trim ..................................................................168L-Trim ..................................................................170Mini-Bead™ 800 & 900 ........................................172U-Trim/Spackle-J ................................................169
Metal Corner Beads ............................................152–157Metal Lath ..........................................................225–235Metal Trims ..........................................................168–170Metal Trusses ......................................................136–140Metric ..............................................................................5Mini-Bead™ ..................................................................175Mold ..............................................................................9MSDS Sheets ......................................inside back coverMudable J-Bead — Vinyl ............................................184
■ ■ ■ ■ ■ N ■ ■ ■ ■ ■
Nonload-Bearing ......................................................24–39Nonload-Bearing Walls ............................................26–33Nonstructural Framing ............................................24–39Nonstructural Studs ................................................26–33
■ ■ ■ ■ ■ O ■ ■ ■ ■ ■
One-Coat Veneer Beads & Trims ........................204–207Overlap Details — Paper-Backed Lath ..............227–230Overtrack............................................................45, 70–71
■ ■ ■ ■ ■ P ■ ■ ■ ■ ■
Paper-Faced Beads & TrimsPaper-Faced 3/4" Bullnose Off-Angle
Outside Corner — Nail-On ..........................197Paper-Faced 3/4" Bullnose Off-Angle
Outside Corner — Tape-On ........................195Paper-Faced 3/4" Bullnose Outside Corner —
Nail-On ..........................................................196Paper-Faced 3/4" Bullnose Outside Corner —
Tape-On ........................................................194Paper-Faced Drywall Corner Beads ............190–191Paper-Faced Inner Cove Trim — Tape-On ..........198Paper-Faced Metal Inside Corner — Tape-On ....192Paper-Faced Metal L-Trim — Tape-On ..............199Paper-Faced Metal Off-Angle Inside Corner ......193Paper-Faced Metal Off-Angle Outside Corner —
Tape-On ........................................................191Paper-Faced Metal Outside Corner — Tape-On ..190Paper-Faced Metal Reveal Trim — Tape-On........200
Paper-Backed Metal Lath ....................................226–230Partition End Cap — Vinyl ..........................................186Party Wall ............................................................146–147Physical Properties................................inside back coverPlant Locations ................................................................3Plaster Beads & Trims ........................................218–221Plaster Casing Beads ..........................................212–215Plaster Control Joints ..........................................216–221Plaster Corner Beads ..........................208–209, 211, 216Prefabricated Metal Trusses ................................138–139Press Brake Shapes ....................................................222Product Labeling..............................................................4Product Specification ..........................................242–243Product Submittal ................................inside back coverProtective Coating ..................................................4, 243
236-244 Index Pages:DMF07_212-217_Index 7/15/10 4:53 PM Page 239
Inde
x
240 The place to stop…before the building starts! SMrequest a quote online @
■ ■ ■ ■ ■ Q ■ ■ ■ ■ ■
QuickClip™ ....................................................................97Quicksilver® ..................................................................12Quicksilver™ Corner Bead ..........................................153QuickTwist™ Web Stiffener ..........................................126
■ ■ ■ ■ ■ R ■ ■ ■ ■ ■
Race Track Bead..........................................................200RC-1 & RC-2..................................................................52RC Deluxe™ ..............................................................12, 52Recycled Content ........................................................11Resilient Channel ..........................................................52Rigid Connectors/Accessories ..............................92–104Rim Joist ....................................................................122Rip Bead™ ....................................................................12Rip L-Bead ..................................................................186Roof Trusses ........................................................135–140Runner Track ..........................................................36–37
■ ■ ■ ■ ■ S ■ ■ ■ ■ ■
S-Series™ Support Clip ........................................100, 124Screeds
Sill Screed ............................................................222SI36 5-1/2" Sill Screed ........................................2221-3/8" J-Weep ....................................................223J-Weep High-Back Plaster Stop ........................224F.H.A.7. Foundation Screed ................................222Econo Screed ......................................................222
Screw Bar ....................................................................51Security Lath ..............................................................236Seismic Ties ................................................................140Self-Furring Dimpled Lath ..........................................229Self-Furring V-Groove Mesh Lath ..............................230Shaftwall/Stairwell Framing ................................144–145Shear Wall Strapping ..................................................109Shiny 90 ......................................................................153Shiny Corner Bead ......................................................153Shop Drawings ..............................................................19Short-Flange Casing Bead ..................................214–215Sill Screeds ........................................................222–224Simpson™ Hangers ..............................................128–132Simpson™ Holdowns ..................................................105Simpson™ Lateral Tie Plate ..........................................132Simpson™ Seismic Ties................................................140Simpson Strong-Tie™ ....................................................12
Simpson™ Tension Ties ..............................................105Single-Leg Resilient Channel ........................................52Skewable Angle Hangers ............................................132Slide Clips ................................................................93-96Slip Connectors/Accessories ..................................92–97Slip Track — Drywall ....................................................42Slip Track — Structural ............................................66–67SLP-TRK® ....................................................12, 42, 66–67Slotted Slip Track — Drywall ........................................42Slotted Slip Track — Structural ..............................66–67Slotted Track ......................................................42, 66–67Sound Channel (RC Series) ....................................52–53Sound Rated Assemblies ..................................35, 52–53Spackle J-Trim ............................................................161Span Tables ..........................................inside back coverSpazzer™ 5400 ................................................12, 68, 106Spazzer™ 9200 ..................................................12, 43, 46Spazzer® Bar Guard™ ............................................68, 106Spazzer® Bridging Bars..........................................46, 106Spazzer® Snap-In Grommet ........................................106Specifications ..................................................................5Splayed Bullnose Corner Bead — Vinyl ....................178Splayed Corner Angle ..................................................50Splayed Corner Bead — Metal....................................155Splayed Corner Bead — Vinyl ....................................177Squash Blocks ....................................................126–127SSMA ..............................................................................4Standards ........................................................................5STC Rating ....................................................................52Steel Thickness........................................................5, 235Strip Lath ............................................................210, 232Stucco Products ................................................208–224Structural Blocking ..............................................124,128Structural Studs ......................................................62–63Studs, Steel ................................................26–33, 62–63Submittals ............................................inside back coverSuperDrive™....................................................................12Support Clips (A-Series™) ..........................................104Support Clips (B-Series™) ..........................................102Support Clips (E-Series™) ......................................99, 124Support Clips (S-Series™) ..................................100, 124Support Clips (U-Series™) ..........................................101Support Clips (X-Series™) ............................................103
■ ■ ■ ■ ■ T ■ ■ ■ ■ ■
Tabbed Track ..............................................................145Technical Services ........................................................19Tension Bracing ..........................................................128Termites ..........................................................................9
236-244 Index Pages:DMF07_212-217_Index 7/15/10 4:53 PM Page 240
Index
241For more information or to contact a sales representative, see page 3
Thickness ................................................................5, 243Tie Wire ..........................................................48–49, 234Top & Bottom Plate — Drywall ..............................36–39Top & Bottom Plate — Structural ................................65Track, Drywall ..........................................................36–37Track, Structural ............................................................65TradeReady® ..................................................................12TradeReady® Floor System ................................120–123TradeReady® Grommet ................................................121TradeReady® Header......................................................89TradeReady® Spazzer® 5400 Bar ................................106TradeReady® Spazzer® 9200 Bar ..................................46Transition Caps ............................................................159Trim Products
Metal ............................................................152–172Paper-Faced ................................................190–200Veneer ..........................................................204–207Vinyl ..............................................................176–186
Truss Framing ......................................................135–140Truss Types ..................................................................137
■ ■ ■ ■ ■ U ■ ■ ■ ■ ■
U-Series™ Support Clip ................................................101U-Trim — Metal ..........................................................169U-Channel ............................44, 47–48, 68–69, 107–108UL™ Listed ..........................23, 40, 42, 66, 120, 138, 148Ultra-Span® ....................................................................12UltraSTEEL®
Benefits ............................................................24–25Composite Limiting Heights ............................28–33Contour Track® ................................................38–39Fire Assemblies ......................................................36Framing ............................................................26–37Knockouts ..............................................................27Physical and Structural Properties ............28, 30, 32Sound Assemblies ................................................37Studs ......................................................................26Track ................................................................34–35
Uni-Clip™ ................................................................12, 98Utility Angle ..........................................................50, 112
■ ■ ■ ■ ■ V ■ ■ ■ ■ ■
V-Goove Lath ..............................................................230Veneer Beads & Trims ........................................204–207Veneer Control Joint ..................................................205Veneer Corner Beads ..........................................172, 204Vinyl #1 Corner Bead ..................................................176
Vinyl Corp...............................................................13, 175Veneer Plaster: Trims & Accessories
1A Expanded Flange Corner Bead — Galvanized ....................................................208
Mini-Bead™ 800 and Mini-Bead 900 ....................172Veneer Trims 701A J-Trim ....................................206Veneer Trims 701B L-Trim ....................................207Control Joint 093 ................................................205Double-X Corner Bead — Galvanized ................209
Vinyl Corner Beads & TrimsVinyl Corner Bead ................................................176Vinyl #1 with 2-1/2" Legs ....................................176Vinyl Splayed Corner Bead (120/135˚) ................177Vinyl Archway Corner Bead ................................177Vinyl Bullnose ......................................................178Vinyl Bullnose Arch Bead ....................................179Vinyl Bullnose Kerfed............................................179Vinyl Bullnose Splayed ........................................178Vinyl J-Bead ........................................................184Vinyl Mudable J-Bead ........................................184Vinyl L-Stop ........................................................185Vinyl Rip Bead™ ....................................................185Vinyl Partition Cap ..............................................186Vinyl 093 Control Joint ........................................186
■ ■ ■ ■ ■ W ■ ■ ■ ■ ■
Warranty ..........................................................................5Website ................................................inside back coverWeb Stiffeners ....................................................126–127
■ ■ ■ ■ ■ X ■ ■ ■ ■ ■
X-Bracing ............................................................110–111X-Series™ Support Clip ................................................103
■ ■ ■ ■ ■ Y ■ ■ ■ ■ ■
Yield Strength ........................................................4, 243
■ ■ ■ ■ ■ Z ■ ■ ■ ■ ■
Z-Bar ........................................................................56Z-Furring Channel ........................................................56Zinc Control Joint 38, 50, 75 & 100 ............................217Zinc Control Joints ............................................171, 205Zinc Mini-Bead™ ..........................................................204
236-244 Index Pages:DMF07_212-217_Index 7/15/10 4:53 PM Page 241
MATERIAL CERTIFICATION
Design Specification (AISI)“Specifications for the Design of Cold-Formed Steel Structural Members”
Product Specification (ASTM)Drywall Nonload-Bearing (Nonstructural) Framing and Accessories ........................C 645
Structural Framing and Accessories ..........................................................................C 955
Plastering Steel Products ..........................................................................................C 847
Veneer and Plaster Accessories ....................................................................C 841/C 1063
Beads and Trims – Metal – Paper – Vinyl ................................................................C 1047
Material Specification (ASTM)Drywall Nonload-Bearing (Nonstructural) Framing – No accessories ..........A 1003 (NS33)
Structural Framing and Accessories ......................A 1003 (ST33L, ST33H, ST50L, ST50H)
Plastering Steel Products ..........................................................................................A 653
Veneer and Plaster Accessories ........................................................................A 653/B 69
Beads and Trims – Metal – Paper – Vinyl ........................................................A 653/A 591
Coating Specification (ASTM)Drywall Nonload-Bearing (Nonstructural) Framing and Accessories ........................C 645
Structural Framing and Accessories ........................................................................C 955*
Plastering Steel Products ..........................................................................................A 653
Veneer and Plaster Accessories ..............................................................................C 1063
Beads and Trims – Metal – Paper – Vinyl ................................................................C 1047
Additional InformationMSDS, limiting heights, code-body reports and individual product specification sheets areavailable at www.dietrichmetalframing.com
* Structural Framing products are available with a variety of protective coatings. G60 zinccoatings meet the most widely applicable building codes and we are able to provide certified G60 product that meets the G60 coating weight provisions of ASTM C 955.Certified G90 coatings are an enhanced option that can be requested for highly corrosiveenvironments. G60E coatings are an economical choice. G60E coatings for structuralproducts will pass the 100-hour salt spray test applicable to "equivalent" coatings underASTM A 1003, but cannot be certified by any supplier to meet the G60 minimum coatingstandard under ASTM C 955. The buyer is solely responsible to assure that products purchased properly satisfy any applicable code or specification.
242
ASTM SpecificationDescriptionsA 591Standard Specification for Steel Sheet,Electrolytic Zinc-Coated, for Light CoatingWeight [Mass] Applications
A 653Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy Coated(Galvannealed) by Hot-Dip Process
A 1003Standard Specification for Steel Sheet,Carbon, Metallic- and Nonmetallic-Coated for Cold Formed Framing Members
B 69Standard Specification for Rolled Zinc
C 645Standard Specification for Nonstructural SteelFraming Members
C 841Standard Specification for Installation ofInterior Lathing and Furring
C 847Standard Specification for Metal Lath
C 955Standard Specification for Load-Bearing(Transverse and Axial) Steel Studs, Runners(Tracks), and Bracing or Bridging for ScrewApplication of Gypsum Panel Products andMetal Plaster Bases.
C 1047Standard Specifications for Accessories forGypsum Wallboard and Gypsum Veneer Base
C 1063Standard Specifications for Installation ofLathing and Furring to Receive Interior andExterior Portland Cement-Based Plaster.
236-244 Index Pages:DMF07_212-217_Index 7/15/10 4:53 PM Page 242
243
Yield Strength, Fy/(psi or ksi)Yield strength is the property by which the strength of steel is typically defined. Dietrich 20 and 18-gauge products are manufactured with steel having a yield point of 33 ksi. 16, 14 and 12 gaugeproducts are manufactured with steel having a yield point of 50 ksi. Ksi is short for kips per squareinch. One kip is equal to 1,000 pounds.
Recycled ContentLight-gauge steel framing is recognized as a recycled content product with the LEED Green BuildingRating System**. Dietrich Metal Framing™ products contain a high content of recycled steel.
** LEED and LEED Green Building Rating System are service marks of the U.S. Green Building Council.
Minimum thickness is 95% of the design thickness per AISI code
Protective CoatingDietrich Metal Framing offers a variety of galvanized products that can be selected to meet the specific requirements of a project.
Non- structural products have a corrosion resistant galvanized coating that conforms to ASTMspecification A1003 – G40 coating weight or equivalent corrosion protection. This coating is in accordance with the industry standard coating requirements of ASTM C 645. These productscan also be ordered with enhanced coatings for special applications.
Structural Framing products are available with a variety of protective coatings. G60 zinc coatings meet the most widely applicable building codes and we are able to provide certifiedG60 product that meets the G60 coating weight provisions of ASTM C 955. Certified G90 coatings are an enhanced option that can be requested for highly corrosive environments.G60E coatings are an economical choice. G60E coatings for structural products will pass the100-hour salt spray test applicable to "equivalent" coatings under ASTM A 1003, but cannotbe certified by any supplier to meet the G60 minimum coating standard under ASTM C 955.The buyer is solely responsible to assure that products purchased properly satisfy any applicable code or specification.
Steel Thickness with Color Code
Thickness ASTM
Gauge Mils Design Thickness Minimum Thickness ColorInches mm Inches mm Code**
25 18 0.0188 0.478 0.0179 0.455 None20 DW 30 0.0312 0.792 0.0296 0.752 Pink20 STR 33 0.0346 0.879 0.0329 0.836 White
18 43 0.0451 1.146 0.0428 1.087 Yellow16 54 0.0566 1.438 0.0538 1.367 Green14 68 0.0713 1.811 0.0677 1.720 Orange12 97 0.1017 2.583 0.0966 2.454 Red
Steel Thickness with Color Code
*Not available in all locations**The term “Effective Thickness” was created by Underwriters Laboratory (UL) to establish a minimum thicknessmeasurement after the UltraSTEEL® manufacturing process has occurred. Effective thickness is the measurementacross the peaks of the dimples or the thickest part of the steel. The manufacturing, base steel and quality controlprocess is verified by independent third party UL representatives, who make regular unannounced visits to Dietrich’smanufacturing facilities to assure full compliance with UL established quality control standards.***Color coded product may or may not be available. Varies by market.
Thickness ASTM
Gauge Mils Effective Thickness** Minimum Thickness ColorInches mm Inches mm Code***
25EQ 15 0.034 0.86 0.015 0.38 None20DW EQ 25 0.055 1.34 0.025 0.63 Pink20STR EQ* 28 0.060 1.52 0.028 0.71 White
UltraSTEEL® Non-Structural Steel Thickness with Color Code
Corporate Headquarters
200 Old Wilson Bridge Rd.
Columbus, OH 43085
800-873-2604
Manufacturing andSales Locations
United StatesCalifornia Colton .................. 909-824-9717
Stockton .............. 209-547-9066
Colorado Denver ................. 303-289-4092
Georgia McDonough ......... 678-304-5500
Hawaii Kapolei ................ 808-682-5747
Indiana Hammond ............ 219-931-3741
Kansas Lenexa ................ 913-599-2026
Maryland Baltimore ............. 410-477-8700
New Jersey Boonton ............... 973-335-3240
Ohio Warren ................ 330-372-4014
Texas Baytown .............. 281-383-1617
Hutchins .............. 972-225-1100
Other Dietrich DivisionsVinyl Corp. ..................................... 800-648-4695
Dietrich Design Group North ......... 800-873-2443
or ....................... 219-853-9474
Dietrich Design Group South ......... 800-873-2443
or ....................... 687-304-5525
Dietrich Design Group West .......... 800-873-2443
or ....................... 760-931-0465
236-244 Index Pages:DMF07_212-217_Index 7/15/10 4:53 PM Page 243
LEED*
CERTIFICATIONBuild Green with Dietrich Metal Framing
LEED® stands for Leadership in Energy &Environmental Design. LEED® Green BuildingRating System, as promulgated by the U.S.Green Building Council, is to improveenvironmental and economic performance
of commercial buildings using established or advancedindustry principles, practices, materials and standards.
Dietrich recognizes the importance and growing agenda ofLEED®. We are members of the U.S. Green Building Counciland have LEED® Accredited Professionals on staff.
Dietrich Metal Framing can contribute toward LEED credits inseveral areas. In addition to recycled content, the environ-mental impacts resulting from transportation can be reducedas our sales and manufacturing facilities are located within300 miles of 85% of the U.S. population.
Contact your Dietrich representative. Ask how our metalframing products and accessories can contribute towardachieving LEED credits on your next project.
244
Materials and ResourcesMaterials & Resources Credit 4: Recycled Contentintends to increase demand for building products thatincorporate recycled content materials, therefore reducing impacts resulting from extraction and processing of new virgin materials. As discussed anddemonstrated below, steel building products contributepositively toward earning points under Credit 4.1 andCredit 4.2. The following is required by LEED Version 2.2:
Credit 4.1 (1 point) "Use materials with recycled contentsuch that the sum of post-consumer recycled contentplus one-half of the pre-consumer content constitutes atleast 10% of the total value of the materials in the project."
Credit 4.2 (1 point) "Use materials with recycled contentsuch that the sum of post-consumer recycled contentplus one-half of the pre-consumer content constitutes atleast 20% of the total value of the materials in the project."
"The value of the recycled content portion of a materialor furnishing shall be determined by dividing the weightof recycled content in the item by the total weight of allmaterial in the item, then multiplying the resulting percentage by the total value of the item." Since steel(the material) and steel (the building product) are thesame, the value of the steel building product is directlymultiplied by steel's recycled content, or:
Steel Recycled Content Value = (Value of Steel Product)(Post-Consumer % + 1/2 Pre-Consumer %)
The formula above calculates the post-consumer andpre-consumer recycled content percentages for NorthAmerican steel building products. These percentagesand values of steel building products are easily enteredinto the LEED Letter Template spreadsheet for calculation. To illustrate the application of these steelrecycled content values to LEED, manual calculations areshown below for typical Basic Oxygen Furnace (BOF) andElectric Arc Furnace (EAF) steel building products withnominal $10,000 purchases, using 2005 data. Steelbuilding products include light gauge steel framing,structural steel framing (wide flange beams, channels,angles, etc.), rebar, roofing, siding, decking, doors andsashes, windows, ductwork, pipe, fixtures, hardware(hinges, handles, braces, screws, nails), culverts, stormdrains, and manhole covers.
BOF Steel Recycled Content Value for Typical Product:
Light Gauge Steel FramingValue = ($10,000) (24.6% + 1/2 6.6%) = ($10,000)
(27.9%) = $2,790(Exceeds 10% and 20% goals)
EAF Steel Recycled Content Value for Typical Product:
Wide Flange Structural Steel FramingValue = ($10,000) (56.6% + 1/2 32.7%) = ($10,000)
(72.95%) = $7,295(Exceeds 10% and 20% goals)
Information courtesy of The Steel Recycling Institute
* LEED is a registered service mark of the U.S. Green Building Council
236-244 Index Pages:DMF07_212-217_Index 7/15/10 4:53 PM Page 244
INTRODUCTIONDietrich Metal Framing is the largest producer of metal framingand finishing products in the world. As the industry leader,Dietrich offers the best of products, brands, systems, servicesand companies to provide the construction industry with com-prehensive, innovative, low-cost, single-source procurement,supply and building solutions. Dietrich believes leadership isabout action — not simply position. That’s why we continuallystrive to expand our existing markets, develop framingtechnologies, create value-added systems and introduce count-less new products to meet the ever-changing demands of thebuilding and construction industry.
The Products We MakeDietrich Metal Framing is your total source for light-gauge framing and finishing products,systems, services and solutions. Dietrich is your one-stop source for the industry’s widestselection of wall, floor and truss framing, metal, vinyl, veneer and stucco finishing beadsand trims, and a full array of plaster and lath products. We deliver the highest-quality fram-ing and finishing products anywhere in the world. Dietrich delivers everything you need tokeep costs down and productivity up.
■ Axial & Curtain-Wall Framing■ Interior, Nonstructural Framing■ Shaftwall & Area Separation Wall■ Fire-Rated Assemblies■ Floor & Roof Truss Systems■ Deflection Systems■ Metal, Vinyl, Paper-Faced & Veneer Beads and Trims■ Control & Expansion Joints■ Metal Lath & Barrier Mesh■ Stucco & Plaster Beads and Trims■ Prefabricated & Turnkey Building Solutions■ Clips, Connectors & Fasteners
The Value You ReceiveWe provide our customers with a wide rangeof benefits such as supplier consolidation, product rationalization and integrated supplyprograms. Here’s what you can expect:
■ Code Compliant Products
■ Industry’s Broadest Product Line
■ Superior Quality
■ Local Manufacturing with GlobalDistribution
■ Innovative Products, Systems & Services
■ The Most-Specified Light-GaugeManufacturer
■ Best of Brands, Systems & Services
■ Exceptional Customer Care
■ Expert Sales & Field ServiceRepresentatives
■ Professional Technical & DesignAssistance
■ Expert Product Training
The place to stop…before the building starts!SM
www.dietrichmetalframing.com is one of the most advanced
resources for metal framing information in the industry. From
extensive product information to on-line catalogs, to video
installations, this site is your resource to building better, faster
and more profitably. Simply click on any one of our animated
value-added product assemblies for your own personal product
demonstration. You are one click away from adding more profit
to your bottom line.
This website is packed with everything from a basic introduction
to metal framing to elaborate design and productivity tools
including the member sizer program. The construction docu-
ments library features everything from
downloadable/customizable
specifications, certifications,
MSDS, to ICC code approvals.
Looking for alternative
building details, you will
find one of the industry’s
most extensive light-gauge
CAD libraries. This library
is filled with framing alter-
natives that improve effi-
ciency and drive profit to
your bottom line.Need submittals?Dietrich’s on-line submittal system is the easiest way to create
job submittals. Point, click and print for fast, professional
project submittals.
We make it easy for you to do business!
request a quote online @
dietrichmetalframing•
DMF07_IFCIBC:DMF07_IFCIBC 7/15/10 5:06 PM Page 1
■ Veneer, Stucco & PlasterBeads & Trims
■ Metal Lath
The place to stop…before the building starts!SM
Dietrich Metal Fram
ing The M
etal Framing & Finishing Catalog
A Worthington Industries Com
pany
About Worthington IndustriesWorthington Industries is a leading diversified metal processing company with annual sales of approximately$3 billion. The Columbus, Ohio, based company is North America’s premier value-added steel processor and aleader in manufactured metal products such as metal framing, metal ceiling grid systems, pressure cylinders,automotive past model service stampings and laser welded blanks. The company employs more than 8,000people and operates 64 facilities in 10 countries.
©Copyright 2010 by Dietrich Metal Framing. All rights reserved. DMF7/2010Printed in USA 7-10
Manufacturing andSales Locations
Corporate Headquarters
200 Old Wilson Bridge Rd.
Columbus, OH 43085
800-873-2604
California Colton .................. 909-824-9717Stockton .............. 209-547-9066
Colorado Denver ................. 303-289-4092
Georgia McDonough ......... 678-304-5500
Hawaii Kapolei ................ 808-682-5747
Indiana Hammond ............ 219-931-3741
Kansas Lenexa ................ 913-599-2026
Maryland Baltimore ............. 410-477-8700
New Jersey Boonton ............... 973-335-3240
Ohio Warren ................ 330-372-4014
Texas Baytown .............. 281-383-1617Hutchins .............. 972-225-1100
Other Dietrich DivisionsVinyl Corp. ..................................... 800-648-4695Dietrich Design Group North ......... 800-873-2443
or ....................... 219-853-9474Dietrich Design Group South ......... 800-873-2443
or ....................... 687-304-5525Dietrich Design Group West .......... 800-873-2443
or ....................... 760-931-0465
dietrich metalframing •com
Cold-Formed steel framing is recognized as a recycled content product.
10682 DMF07_OBCOFC:DMF07_OBCOFC 7/15/10 5:03 PM Page 1
top related