fittings fittings section x - neia nfc - neiafasteners.comneiafasteners.com/catalog/fittings.pdf ·...
Post on 23-Mar-2018
224 Views
Preview:
TRANSCRIPT
Rev. 9/99 X-a
FITTINGS
Fittings Section X
NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
AIR BRAKE HOSE & FITTINGSAdapter w/Spring 37Adapter Hose End 37Field Installation Kit 37Gladhand Seal 37Hose Mender 37Hose Sleeve 37Nut 37Rubber Air Hose 37
STEEL PIPE FITTINGS - BLACK45 Elbow 4545 Street Elbow 4590 Elbow 4590 Street Elbow 45Close Pipe Nipple 44Hex Head Plug 44Bushing 46Coupling 46Nipple 44Union 46Reducing Coupling 46Round Pipe Cap 44Socket Head Plug 44Square Head Plug 44Tee 45
AIR BRAKE - NTA FITTINGS - BRASS45 Male Elbow 3490 Male Elbow 33Bulkhead Union 35Female Connector 34Female Elbow 34Insert (Stainless Steel) 32Male Branch Tee 35Male Connector 33Male Run Tee 35Nut 32Nylon Tubing 31Sleeve 32Union 32, 34Union Tee 35
COMPRESSION - BRASSAdapter Tee 9Brass Insert 8Bulkhead union 10Compression Nut 8Female Connector 9Female Elbow 10Male Connector 9Male Branch Tee 9Male Elbow 10Male Run Tee 10Tapered Sleeve 8Union 8Union Elbow 8Union Tee 8
INVERTED FLARED - BRASS45 Elbow 17Female Branch Tee 18Female Connector 16Long Nut 15Male Connector 16Male Elbow 17Male Run Tee 18Steel Nut 15Steel Plug 17Union 15Union Elbow 17Union Tee 16
HOSE BARB - BRASSBeaded Hose Barb 45 Elbow to Male Pipe 26Beaded Hose Barb 90 Elbow to Male Pipe 26Beaded Hose Barb Straight to Male Pipe 26Hose Barb 45 26Hose Barb 90 Elbow to Male Pipe 26Hose Barb to Female Pipe 25Hose Barb to Male Pipe 25Hose Barb to SAE Flared Swivel 26Hose Mender 25
Rev.05/08
FITTINGS
X-b Rev. 9/99
Fittings Section X
NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
PIPE FITTINGS - BRASS45 Street Elbow 23Adapter 23Branch Tee 23Bulkhead Fitting 23Bushing 21Cap 21Close Nipple 22Countersunk Hx Pipe Plug 21Coupling 20Cross 20Female 90 Union Elbow 20Hex Head Plug 21Hex Nipple 22Hex Reducer Nipple 22Lock Nut 22Long Nipple 22Reducer Coupling 20Slotted Plug 21Square Head Plug 21Street Elbow 22Street Tee 23Tee 20Union 20
45 DEGREE SAE FLARED - BRASS45 Male Elbow 590 Male Elbow 5Cap Nut 4Copper Tubing 6Female Connector 4Female Elbow 5Female Flared to Male Pipe 6Flared Seal Plug 4Inverted Flare to SAE 45 Flared Adapter 6Male Branch Tee 3Male Connector 6Male Run Tee 4Nuts 3Reducer Union 4Union 3Union Elbow 5Union Tee 3
COIL AIR & SHOP AIR HOSEAir Chuck 41bAir Tank Valve 41aBall Swivel Fittings 41bBlow Gun
Adjustable 41aLever 41aTyphoon 41aTyphoon Extensions 41a
Brass Hose Ferrules 41bCoil Air Hose 41aExtension Chuck 41bService Guage 41bShop Air Hose 41a
DRAIN COCK, SHUTOFF COCKSBib Drain Valve 29Drain Cock 30External Seal Drain Cock 29Ground Plug Shutoff Cock 30
GREASE FITTINGS45 Elbow 43a65 Elbow 43a90 Elbow 43aAdapter 43aDrive-In 43aMetric 43aStraight 43a
GREASE GUNGrease Gun Coupler 43bGrease Gun Hose 43bLever Style 43bPistol Style 43b
HOSE & TRUCKReusable Hose End 38bTruck Hose 38b
Rev.05/08
Rev. 9/99 X-c
FITTINGS
Fittings Section X
NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
HYDRAULIC BRAKE LINE & FITTINGSCoupling Union 42No-Kink Brake Line
Domestic (Doubled Flared End) 42European (Bubble Flare) 42Japanese (Concave) 42
NYLON TUBING 31 & 36
PRESTOLOK BRASSMale Connector 12Swivel
Male Branch Tee Swivel 13Male Elbow Swivel 90 12Male Run Tee Swivel 13
Union 12Union Tee 12
PRESTOMATIC D.O.T. BRASS AIR BRAKEMale Connector 38Male Elbow 38Union 38Union Tee 38
SALES AIDSBrass Air Brake NTA 31Brass Compression 7Brass Hose Barb 24Brass Inverted Flared 14Brass Pipe 19Drain Cock & Shutoff 29Pipe Thread Gauge 1Prestolok Brass 11SAE 45 Flared Brass 2Tube Fittings Thread
Size Comparison Chart 1
SERVICE AIR HOSE & FITTINGS
CouplersFemale 40Male 40
NipplesFemale 40Male 40
TRANSMISSION SHIFTER LINEMale Elbow 36Male Connector 36Nut 36Split Sleeve 36Union 36
VALVEBall 27Plug
Female Pipe to Female 27Female Pipe to Male 27Male Pipe to Male 27
TruckHose to Male Pipe 28Female Pipe to Male Pipe 28Flare to Male Pipe 28
STEEL 37 JIC ADAPTERS90 Male Elbow 38aCap 38aMale Adapter 38aPlug 38aStraight Thread Adapter 38aStraight Thread 90 Elbow 38aUnion 38a
SWING COUPLINGS 39Accessories 39
Rev.05/08
FITTINGS
X-1Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Fittings General Information
The chart below lists the thread size for the different fitting styles and sizes.EXAMPLE: Compression fitting with 1/4" tube size has a thread size of 7/16-24.
Use this gauge (Actual Size) to measure Pipe Thread sizes.
Rev. 2/13
TUBE FITTING THREAD SIZECOMPARISON CHART
Dash Size
Tube OD
Pipe Thread SAE O-Ring & 37o
JIC Flare45o SAE
FlareFlat Face Thread
Inverted Flare
Brass Compression
-02 1/8 1/8-27 5/16-24 5/16-24 N/A 5/16-28 5/16-24
-03 3/16 N/A 3/8-24 3/8-24 N/A 3/8-24 3/8-24
-04 1/4 1/4-18 7/16-20 7/16-20 9/16-18 7/16-24 7/16-24-05 5/16 N/A 1/2-20 1/2-20 N/A 1/2-24 1/2-24-06 3/8 3/8-18 9/16-18 5/8-18 11/16-16 9/16-24 9/16-24-07 7/16 N/A N/A 11/16-16 N/A 5/8-24 5/8-24-08 1/2 1/2-14 3/4-16 3/4-16 13/16-16 11/16-20 11/16-20-10 5/8 N/A 7/8-14 7/8-14 1-14 13/16-18 13/16-18-12 3/4 3/4-14 1 1/16-12 1 1/16-14 1 3/16-12 1-18 1-18-14 7/8 N/A 1 3/16-12 N/A N/A N/A N/A-16 1 1-11 1/2 1 5/16-12 N/A 1 7/16-12 N/A N/A-20 1-1/4 1-1/4-11 1/2 1 5/8-12 N/A 1 11/16-12 N/A N/A-24 1-1/2 1-1/2-11 1/2 1 7/8-12 N/A 2-12 N/A N/A-32 2 2-11 1/2 2 1/2-12 N/A N/A N/A N/A
FITTINGS
X-2 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
See Your Sales RepresentativeAbout Our
Custom Made Assortments.Have The Proper Fitting On Hand
When You Need It!
AdvantagesThis economical fitting resists mechanical pullout. Can beassembled and disassembled repeatedly. Manufacturedfrom CA 360, CA 345 or CA 377 brass.
SpecificationsListed with Underwriter’s Laboratories for flammable liquid,marine, refrigeration and gas applications. Meets functionalrequirements of SAE, ASA, ASME and MS (MilitaryStandards).
ApplicationsUse with copper, brass, aluminum and welded steel hydrau-lic tubing that can be flared. Manufactured especially forhard-to-hold liquids and gases.
Temperature RangesFrom -65° to +250°F.
VibrationShort nut may be used when vibration is minimal. The longnut offers additional vibration capacity.
SizesTube sizes are determined by the numbers of sixteenths ofan inch in the tube O.D.
Working Pressure RangesTemperature and type of tubing used are important factors.However, the following table is a good guide for properselection. Temperature 73°F with copper tubing:
PSI Tube O.D. (in.) Tube Wall (in.)2800 1/8 .0301900 3/16 .0301400 1/4 .0301200 5/16 .0321000 3/8 .032750 1/2 .032650 5/8 .035550 3/4 .035450 7/8 .035
Assembly Instructions1. Cut tubing squarely and remove burrs.2. Place nut onto tube. Place threaded end of nut toward3. Flare tube end with flaring tool to provide 45° flare.4. Clamp tube flare between nut and nose of fitting body by
screwing nut on finger-tight. Tighten with a wrench for ametal-to-metal seal.
Flare fittings are easy to disassemble and may be reas-sembled repeatedly, for a leak-proof connection.
SAE 45° Flared Brass Fittings
Rev. 8/93
FITTINGS
X-3Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
SAE 45° Flared Brass Fittings
Long Nut Short Nut
Male Branch TeeUnion Tee
Union
B
A C
Tube Parker W'headPart No. Size No. No. 70011 3/16 41FL-3 41X3 70012 1/4 41FL-4 41X4 70013 5/16 41FL-5 41X5 70014 3/8 41FL-6 41X6 70018 1/2 41FL-8 41X870019 5/8 41FL-10 41X10
Tube Parker W'headPart No. Size No. No.70027 1/4 41FS-3 1110X470028 5/16 41FS-5 1110X570029 3/8 41FS-6 1110X670032 1/2 41FS-8 1110X870033 5/8 41FS-10 1110X1070034 3/4 42FS-12 1110X12
Tube Parker W'headPart No. Size No. No. 70076 3/16 144F-3 44X3 70077 1/4 144F-4 44X4 70078 5/16 155F-2 44X5 70079 3/8 144F-6 44X6 70081 1/2 144F-8 44X8 70082 5/8 144F-10 44X10
Tube Parker W'headPart No. Size No. No. 70050 1/8 42F-2 42X2 70051 3/16 42F-3 42X3 70052 1/4 42F-4 42X4 70053 5/16 42F-5 42X570054 3/8 42F-6 42X6 70056 1/2 42F-8 42X8 70057 5/8 42F-10 42X10 70058 3/4 42F-12 42X12
Tube Parker W'headPart No. Size No. No. 70090 3/16X1/8 45X3 70091 1/4 X 1/8 145F-4-2 45X4 70092 1/4X1/4X1/4 145F-4-4 45X4X4X4 70093 5/16 X 1/8 145F-5-2 45X5 70094 3/8 X 1/4 145F-6-4 45X6 70095 3/8 X 3/8 145F-6-6 45X6X6X6 70097 1/2 X 3/8 145F-8-6 45X8 70098 1/2 X 1/2 145F-8-8 45X8X8X8 70099 5/8 X 1/2 145F-10-8 45X10 70100 3/4 X 1/2 145F-12-8 45X12
Rev. 5/94
FITTINGS
X-4 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
SAE 45° Flared Brass Fittings
Flared Seal Plug Female Connector
Reducer Union
B
A
C
Male Run Tee
Cap Nut
*Should be used with copper gasket.
Part Tube Parker W'headNo. Size No. No.
70001 3/16"70002 1/4" 639F-470003 5/16" 639F-570004 3/8" 639F-670006 1/2" 639F-870007 5/8" 639F-10
Part Tube Tube Parker W'headNo. Size Thread No. No.
70065 3/8" 1/4" 42F-6-470067 1/2" 3/8" 42F-8-670068 5/8" 1/2" 42F-10-8
Part "A" "B" "C" Parker W'headNo. Tube Tube Pipe No. No.
O.D. O.D. Thread70201 3/16" 3/16" 1/8" 51X370202 1/4" 1/4" 1/8" 151F-4-2 51X470203 5/16" 5/16" 1/8" 51X570204 5/16" 5/16" 1/4" 151F-5-4 51X5X4X570205 3/8" 3/8" 1/4" 151F-6-4 51X670206 3/8" 3/8" 3/8" 151F-6-6 51X6X6X670207 1/2" 1/2" 3/8" 151F-8-6 51X870208 1/2" 1/2" 1/2" 151F-8-8 51X8X8X870209 5/8" 5/8" 1/2" 151F-10-8 51X10
Part Tube Pipe Parker W'headNo. Size Thread No. No.
70106 3/16" 1/8" 46F-3-2 46X370107 1/4" 1/8" 46F-4-2 46X470108 1/4" 1/4" 46F-4-4 46X4X470109 5/16" 1/8" 46F-5-2 46X570110 5/16" 1/4" 46F-5-4 46X5X470111 3/8" 1/8" 46F-6-2 46X6X270112 3/8" 1/4" 46F-6-4 46X670113 3/8" 3/8" 46F-6-6 46X6X670114 3/8" 1/2" 46F-6-8 46X6X870115 1/2" 1/4" 46F-8-4 46X8X470116 1/2" 3/8" 46F-8-6 46X870117 1/2" 1/2" 46F-8-8 46X8X870118 5/8" 1/2" 46F-10-8 46X10
Part Tube Parker W'headNo. Size No. No.
70126 3/16" 640F-3* 70127 1/4" 640F-4* 70128 5/16" 640F-5* 70129 3/8" 640F-6* 70131 1/2" 640F-8* 70132 5/8" 640F-10* 70133 3/4"
Rev. 6/97
FITTINGS
X-5Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
SAE 45° Flared Brass Fittings
90° Male Elbow
Union Elbow
Female Elbow
Tube Pipe Parker W'headPart No. Size Thread No. No. 70165 1/8 1/8 149F-2-2 49X2 70166 3/16 1/8 149F-3-2 49X3 70167 1/4 1/8 149F-4-2 49X4 70168 1/4 1/4 149F-4-4 49X4X4 70169 1/4 3/8 149F-4-6 49X4X6 70170 5/16 1/8 149F-5-2 49X5 70171 5/16 1/4 149F-5-4 49X5X4 70172 3/8 1/8 149F-6-2 49X6X2 70173 3/8 1/4 149F-6-4 49X6 70174 3/8 3/8 149F-6-6 49X6X6 70175 3/8 1/2 149F-6-8 49X6X8 70176 7/16 1/4 49X7 70177 1/2 1/4 149F-8-4 49X8X4 70178 1/2 3/8 149F-8-6 49X8 70179 1/2 1/2 149F-8-8 49X8X8 70180 5/8 3/8 149F-10-6 49X10X6 70181 5/8 1/2 149F-10-8 49X10 70182 3/4 1/2 149F-12-8 49X12 70183 3/4 3/4 149F-12-12 49X12X12
Tube Parker W'headPart No. Size No. No.70247 1/4 155F-4 55X470248 5/16 155F-5 55X570249 3/8 155F-6 55X670251 1/2 155F-8 55X870252 5/8 155F-10 55X10
Tube Pipe Parker W'headPart No. Size Thread No. No.70230 1/4 1/8 159F-4-2 54X470231 1/4 1/4 159F-4-4 54X4X470232 5/16 1/8 159F-5-2 54X570233 3/8 1/4 159F-6-4 54X670234 3/8 3/870235 1/2 3/8 159F-8-6 54X870236 5/8 1/2 159F-10-8 54X1070237 5/8 3/8
45° Male Elbow
Tube Pipe Parker W'headPart No. Size Thread No. No.70185 3/16 1/8 50X370186 1/4 1/8 150F-4-2 50X470187 1/4 1/4 150F-4-4 50X4X470188 5/16 1/8 150F-5-2 50X570189 5/16 1/4 150F-5-4 50X5X470190 3/8 1/4 150F-6-4 50X670191 3/8 3/8 150F-6-6 50X6X670192 1/2 3/8 150F-8-6 50X870193 1/2 1/2 150F-8-8 50X8X870194 5/8 1/2 150F-10-8 50X10
Rev. 8/93
FITTINGS
X-6 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Invverted Flareto
SAE 45° Flared Adapter
SAE 45° Flared Brass Fittings
Go from Inverted Flared to SAE 45 Flaredfitting with this special adapter.
Male Connector
Female Flare toMale Pipe Thread
Tube Pipe Parker W'headPart No. Size Thread No. No.70140 1/8 1/8 48F-2-2 48X270141 3/16 1/8 48F-3-2 48X370142 1/4 1/8 48F-4-2 48X470143 1/4 1/4 48F-4-4 48X4X470145 5/16 1/8 48F-5-2 48X570146 5/16 1/4 48F-5-4 48X5X470147 3/8 1/8 48F-6-2 48X6X270148 3/8 1/4 48F-6-4 48X670149 3/8 3/8 48F-6-6 48X6X670150 3/8 1/2 48F-6-8 48X6X870151 7/16 1/4 48X770152 1/2 1/4 48F-8-4 48X8X470153 1/2 3/8 48F-8-6 48X870154 1/2 1/2 48F-8-8 48X8X870155 5/8 3/8 48F-10-6 48X10X670156 5/8 1/2 48F-10-8 48X1070157 3/4 1/2 48F-12-8 48X1270158 3/4 3/4 48F-12-12 48X12X12
SAE 45 FlaredTube
Part No. Size70257 1/4
Inverted FlareTubeSize1/4
Tube Pipe Parker W'headPart No. Size Thread No. No.70255 1/4 1/4 664FHD-4-4*
* Should be used with copper gasket.
Part No. O.D.70280 1/8"70281 3/16"70282 1/4"70283 5/16"70284 3/8"70285 1/2"70286 5/8"
Copper TubingComes in 50 ft rolls.
Rev. 7/96
FITTINGS
X-7Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Brass Compression Fittings
AdvantagesNo flaring, soldering or other preparation of tubing neces-sary to assemble. This economical fitting is readily avail-able in a broad selection of styles. Manufactured from CA360, CA 345 or CA 377 brass.
SpecificationsListed with Underwriter’s Laboratories for flammable Com-pression fittings meet functional requirements of SAE J-512,ASA and ASME.
ApplicationsUse with copper, brass and aluminum. Not recommendedfor steel tubing. Manufactured for low and medium pressuretubing connection work where excessive vibration or tubemovement is not involved.
Temperature RangesFrom -65° to +250°F.
VibrationFair resistance to vibration or tube movement, depending onapplications involved. Use long nut for additional resistanceto vibration.
SizesTube sizes are determined by the numbers of sixteenths ofan inch in the tube O.D.
SizesTube sizes are determined by the numbers of sixteenths ofan inch in the tube O.D.
Working Pressure RangesTemperature and type of tubing used are important factors.However, the following table is a good guide for properselection. Temperature 73°F:
PSI Tube O.D. (in.) Tube Wall (in.)400 1/8 .030400 3/16 .030300 1/4 .030300 5/16 .032200 3/8 .032200 1/2 .032150 5/8 .035100 3/4 .035
75 7/8 .035
Assembly Instructions1. Slide nut, then sleeve onto tubing. The thread end of thenut must face out.2. Insert the tube into the fitting. Be sure the tube isbottomed on the fitting shoulder.3. Assemble nut to body, and tighten "hand-tight". Thenfollow the number of wrench turns as indicated in the follow-ing table.
Turns required toSeal from hand-tight
Fitting Tube With WithSize Size 60C 60PT
2 1/8 1-1/4 -3 3/16 1-1/4 -4 1/4 1-1/4 25 5/16 1-1/4 26 3/8 2-1/4 28 1/2 2-1/4 2
10 5/8 2-1/4 212 3/4 2-1/4 -14 7/8 2-1/4 -
Rev. 8/93
FITTINGS
X-8 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Brass Compression Fittings
Tapered SleeveBrass Insert
Compression Nut
Union Union Elbow
Union Tee
Tube Parker W'headPart No. Size No. No. 70290 1/8 63PT-2-32 70291 3/16 63PT-3-40 70292 1/4 63PT-4-40 70293 5/16 63PT-5-40 70294 3/8 63PT-6-62 70296 1/2 63PT-8-6270297 5/8 63PT-10-62
Tube Parker W'headPart No. Size No. No. 70300 1/8 60C-2 60X2 70301 3/16 60C-3 60X3 70302 1/4 60C-4 60X4 70303 5/16 60C-5 60X5 70304 3/8 60C-6 60X6 70305 7/16 60C-7 60X7 70306 1/2 60C-8 60X8 70307 5/8 60C-10 60X10 70308 3/4 60C-12 60X12
Tube Parker W'headPart No. Size No. No. 70315 1/8 61C-2 61X2 70316 3/16 61C-3 61X3 70317 1/4 61C-4 61X4 70318 5/16 61C-5 61X5 70319 3/8 61C-6 61X6 70320 7/16 61C-7 61X7 70321 1/2 61C-8 61X8 70322 5/8 61C-10 61X10 70323 3/4 6D1C-12 61X12
Tube Parker W'headPart No. Size No. No. 70330 1/8 62C-2 62X2 70331 3/16 62C-3 62X3 70332 1/4 62C-4 62X4 70333 5/16 62C-5 62X5 70334 3/8 62C-6 62X6 70336 1/2 62C-8 62X8 70337 5/8 62C-10 62X10 70338 3/4 62C-12 62X12
Tube Parker W'headPart No. Size No. No. 70355 1/8 164C-2 64X2 70356 3/16 264C-3 64X3 70357 1/4 164C-4 64X4 70358 5/16 164C-5 64X5 70359 3/8 164C-6 64X6 70361 1/2 164C-8 64X8
Tube Parker W'headPart No. Size No. No. 70366 3/16 165C-2 65X3 70367 1/4 165C-4 65X4 70368 5/16 165C-5 65X5 70369 3/8 165C-6 65X6 70371 1/2 165C-8 65X8
Rev. 8/93
FITTINGS
X-9Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Male Connector Female Connector
Brass Compression Fittings
Adapter Tee Male Branch Tee
Tube Pipe Parker W'headPart No. Size Thread No. No. 70375 1/8 1/8 66C-2-2 66X2 70376 3/16 1/8 66C-3-2 66X3 70377 1/4 1/8 66C-3-4 66X4 70378 1/4 1/4 66C-4-4 66X4X4 70379 5/16 1/8 66C-5-2 66X5 70380 5/16 1/4 66C-5-4 66X5X4 70381 3/8 1/8 66C-6-2 66X6X2 70382 3/8 1/4 66C-6-4 66X6 70384 1/2 3/8 66C-8-6 66X8 70385 5/8 1/2 66C-10-8 66X10
Tube Pipe Parker W'headPart No. Size Thread No. No. 70390 1/8 1/8 68C-2-2 68X2 70391 3/16 1/8 68C-3-2 68X3 70393 1/4 1/8 68C-4-2 68X4 70394 1/4 1/4 68C-4-4 68X4X4 70395 5/16 1/8 68C-5-2 68X5 70396 5/16 1/4 68C-5-4 68X5X4 70397 3/8 1/8 68C-6-2 68X6X2 70398 3/8 1/4 68C-6-4 68X6 70399 3/8 3/8 68C-6-6 68X6X6 70400 3/8 1/2 68C-6-8 68X6X8 70401 7/16 1/4 68C-7-4 68X7 70402 1/2 1/4 68C-8-4 68X8X4 70403 1/2 3/8 68C-8-6 68X8 70404 1/2 1/2 68C-8-8 68X8X8 70405 5/8 1/2 68C-10-8 68X10 70406 3/4 1/2 68C-12-8 68X12
Tube Pipe Parker W'headPart No. Size Thread No. No. 70467 1/4 1/8 176C-4-2 76X4
Tube Pipe Parker W'headPart No. Size Thread No. No. 70450 1/8 1/8 172C-2-2 N/A 70451 3/16 1/8 172C-3-2 72X3 70452 1/4 1/8 172C-4-2 72X4 70453 1/4 1/4 172C-4-4 72X4X4X4 70454 5/16 1/8 72X5 70455 3/8 1/4 172C-6-4 72X6 70457 1/2 3/8 172C-8-6 72X8
Rev. 11/99
FITTINGS
X-10 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Brass Compression Fittings
Male Run TeeBulkhead Union
Male Elbow Female Elbow
Tube Pipe Parker W'headPart No. Size Thread No. No. 70410 1/8 1/8 269C-2-2 69X2 70411 3/16 1/8 169C-3-2 69X3 70412 1/4 1/8 169C-4-2 69X4 70413 1/4 1/4 169C-4-4 69X4X4 70414 5/16 1/8 169C-5-2 69X5 70415 5/16 1/4 169C-5-4 69X5X4 70416 3/8 1/8 169C-6-2 69X6X2 70417 3/8 1/4 169C-6-4 69X6 70418 3/8 3/8 169C-6-6 69X6X6 70419 3/8 1/2 169C-6-8 69X6X8 70420 7/16 1/4 69X7 70421 1/2 1/4 169C-8-4 69X8X4 70422 1/2 3/8 169C-8-6 69X870423 1/2 1/2 169C-8-8 69X8X8 70424 5/8 1/2 169C-10-8 69X10 70425 3/4 1/2 169C-12-8 69X12
Tube Pipe Parker W'headPart No. Size Thread No. No. 70431 3/16 1/8 70X3 70432 1/4 1/8 170C-4-2 70X4 70433 5/16 1/8 70X5 70434 3/8 1/4 170C-6-4 70X6 70436 1/2 3/8 170C-8-6 70X8 70437 5/8 1/2 70X10
Tube Parker W'headPart No. Size No. No. 70461 1/4 62CBH-4 74X4 70462 3/8 62CBH-6 74X6
Tube Pipe Parker W'headPart No. Size Thread No. No. 70440 3/16 1/8 171C-3-2 71X3 70441 1/4 1/8 171C-4-2 71X4 70442 1/4 1/4 171C-4-4 71X4X4X4 70443 5/16 1/8 71X5 70444 3/8 1/4 171C-6-4 71X6 70446 1/2 3/8 171C-8-6 71X8
Rev. 8/93
FITTINGS
X-11Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Prestolok Brass Fittings
AdvantagesCompact one piece brass fitting for use with polyethylene,nylon or soft metal tubing. This fitting is specially designedfor low pressure circuits where fast assembly, disassemblyand reassembly is important. No special tools are neededfor assembly; just insert the tubing into the fitting until itbottoms. Prestolok is designed to be used with no tubesupport. Radial claws on the metal grab ring grip thetubing securely to provide retention. Once in the fitting, thetubing can rotate freely even under pressure. Prestolokfeatures swivels on male pipe threaded shapes for installa-tion in tight places and for precise positioning only.Prestolok should not be used for live swivel applications.Sealing is obtained with a nitrile O-ring. Prestolok can beassembled and disassembled repeatedly without impairingits ability to seal. The outside diameter of the tubing to beused with the fitting is marked on the push sleeve. Sizes1/4" and above have internal hexes broached for installationwith an allen wrench in confined areas and close portingapplications.
Working Pressure and Temperature RangesZero to 150° F. at up to 285 psi. Vacuum applications aredependent upon temperature and type of tubing beingused.
ApplicationsUse with Parker series "E" polyethylene tubing, ParkerParflex series "N" nylon tubing or soft metal tubing.Prestolok is designed to conduct air, water, oil and inertgases. Prestolok is ideal for use in pneumatic instrumen-tation circuits and many industrial applications. Allapplications should be carefully tested through the range ofconditions which may be encountered prior to use.
Assembly InstructionsCut nylon and polyethylene tubing squarely with a tubecutter. Metal tubing should be cut squarely and be free ofburrs. Insert end of tubing until it bottoms in fitting.Depressing the release button allows the ;tubing to beremoved.
SizesTube sizes are determined by the numbers of sixteenths ofan inch in the tube O.D.of an inch in the tube O.D.
Rev. 8/93
FITTINGS
X-12 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Make it easy! Use an allenwrench with a connector
Prestolok Brass Fittings
Union Union Tee
Male Elbow Swivel 90°
Male Connector
Tube Parker W'headPart No. Size No. No.71850 1/8 62PL-271851 5/32 62PL-5/3271852 1/4 62PL-471853 5/16 62PL-571854 3/8 62PL-671855 1/2 62PL-8
Tube Parker W'headPart No. Size No. No.71872 1/8 164PL-271873 5/32 164PL-5/3271874 1/4 164PL-471875 5/16 164PL-5/3271876 3/8 164PL-671877 1/2 164PL-8
Tube Pipe Parker W'headPart No. Size Thread No. No.71857 1/8 1/8 68PL-2-271858 1/8 1/4 68PL-2-471859 5/32 1/8 68PL-5/32-271860 1/4 1/8 68PL-4-271861 1/4 1/4 68PL-4-471862 5/16 1/8 68PL-5-271863 5/16 1/4 68PL-5-471864 3/8 1/8 68PL-6-271865 3/8 1/4 68PL-6-471866 3/8 3/8 68PL-6-671867 3/8 1/2 68PL-6-871868 1/2 1/4 68PL-8-471869 1/2 3/8 68PL-8-671870 1/2 1/2 68PL-8-8
Tube Pipe Parker W'headPart No. Size Thread No. No.71879 1/8 1/8 169PL-2-271880 5/32 1/8 169PL-5/32-271881 1/4 1/8 169PL-4-271883 1/4 1/4 169PL-4-471884 5/16 1/8 169PL-5-271885 5/16 1/4 169PL-5-471886 3/8 1/8 169PL-6-271887 3/8 1/4 169PL-6-471888 3/8 3/8 169PL-6-671889 3/8 1/2 169PL-6-871890 1/2 1/4 169PL-8-471891 1/2 3/8 169PL-8-671892 1/2 1/2 169PL-8-8
Rev. 8/93
FITTINGS
X-13Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
See Your Sales RepresentativeAbout Our
Custom Made Assortments.Have The Proper Fitting On Hand
When You Need It!
Prestolok Brass Fittings
Male Run Tee Swivel Male Branch Tee Swivel
Tube Pipe Parker W'headPart No. Size Thread No. No.71894 1/8 1/8 171PL-2-271895 1/4 1/8 171PL-4-271896 1/4 1/4 171PL-4-471897 5/16 1/8 171PL-5-271898 5/16 1/4 171PL-5-471899 3/8 1/4 171PL-6-471900 3/8 3/8 171PL-6-671901 1/2 3/8 171PL-8-671902 1/2 1/2 171PL-8-8
Tube Pipe Parker W'headPart No. Size Thread No. No.71904 1/8 1/8 172PL-2-271905 1/4 1/8 172PL-4-271906 1/4 1/4 172PL-4-471907 5/16 1/8 172PL-5-271908 5/16 1/4 172PL-5-471909 3/8 1/4 172PL-6-471910 3/8 3/8 172PL-6-671911 1/2 3/8 172PL-8-671912 1/2 1/2 172PL-8-8
Rev. 8/93
FITTINGS
X-14 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
AdvantagesBuilt to resist mechanical pullout. This economical fittingcan be assembled and disassembled repeatedly. Readilyavailable in a broad selection of styles to fill your specificneeds. Extruded from CA 360 or CA 345 brass rod.
ApprovalsApproved by Underwriters' Laboratories for flammable liquidand gas. Meets specifications and standards of SAE J512,ASA, ASME, and MS (Military Standards).
ApplicationsUse with copper, brass, aluminum and welded steel hydrau-lic tubing that can be flared. Manufactured especially forhard-to-hold liquids and gases
Working Pressure RangesTemperature and type of tubing used are important factors.However, the following table is a good guide for properselection. Temperature 73°F with copper tubing:
PSI Tube O.D. (in.) Tube Wall (in.)2800 1/8 .0301900 3/16 .0301400 1/4 .0301200 5/16 .0321000 3/8 .032750 1/2 .032650 5/8 .035550 3/4 .035
Temperature RangesFrom -65° to +250°F
VibrationShort nut may be used when vibration is minimal. The longnut offers additional vibration capacity.
Assembly Instructions1. Cut tubing squarely.2. Place nut onto tubing. (Threaded end of nut toward
tubing end.)3. On thin wall copper, welded or brazed tubing, use
double flare to prevent pinch-off or cracked flares.4. Clamp tube flare between nut and flare seat of body byscrewing nut on finger-tight. Tighten with a wrench formetal-to-metal seal.
Note: The seat dimensions are predicated on practicalthreading limitations and use of these fittings with
double flared tubing.
SizesTube sizes are determined by the numbers of sixteenths ofan inch in the tube O.D.
Brass Inverted Flared Fittings
Rev. 8/93
FITTINGS
X-15Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Brass Inverted Flared Fittings
Steel Nut
Long NutUnion
See Your Sales RepresentativeAbout Our
Custom Made Assortments.Have The Proper Fitting On Hand
When You Need It!
Rev. 04/07
Part No.Tube Size Parker No.
W'Head No.
70865 1/8 42 IFHD-2 302X270866 3/16 42 IFHD-3 302X370867 1/4 42 IFHD-4 302X470868 5/16 42 IFHD-5 302X570869 3/8 42 IFHD-6 302X670871 1/2 42 IFHD-8 302X870872 5/8
Part No. Tube SizeParker
No. W'Head No.70836 3/1670837 1/470839 3/8
Part No.Tube Size
Pipe Thread Parker No.
W'Head No.
70800 1/8 41 IFS-2 105X270801 3/16 41 IFS-3 105X370802 3/16 1/470808 3/16 9/16-1870810 1/4 41 IFS-4 105X470811 1/4 5/1670815 1/4 9/16-1870818 5/16 41 IFS-5 105X570821 3/8 41 IFS-6 105X670822 3/8 7/1670825 1/2 41 IFS-8 105X870828 5/8 41 IFS-10 105X1070829 3/4 105X12
FITTINGS
X-16 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
g
Male Connector Female Connector
Union Tee
Brass Inverted Flared Fittings
Part No.Tube Size
Pipe Thread Parker No.
W'Head No.
70845 1/8 1/8 48 IFHD-2-2 202X270846 3/16 1/8 48 IFHD-3-2 202X370847 1/4 1/8 48 IFHD-4-2 202X470848 1/4 1/4 48 IFHD-4-4 202X4X470849 5/16 1/8 48 IFHD-5-2 202X570850 5/16 1/4 48 IFHD-5-4 202X5X470851 5/16 3/870852 3/8 3/8 48 IFHD-6-2 202X6X270853 3/8 1/4 48 IFHD-6-4 202X6X270854 3/8 3/8 48 IFHD-6-6 202X6X670856 1/2 3/8 48 IFHD-8-6 202X870858 5/8 1/2 48 IFHD-10-8
Part No.Tube Size
Pipe Thread Parker No.
W'Head No.
70950 1/8 1/870951 3/16 1/8 46 IFHD-3-270952 1/4 1/8 46 IFHD-4-270953 5/16 1/8 46 IFHD-5-270954 3/8 1/4 46 IFHD-6-470956 1/2 3/8 46 IFHD-8-6
Part No. Tube Size Parker No. W'Head No.70970 1/ X 1/870972 3/16 X 3/16 244 IFHD-370974 1/4 X 1/4 244 IFHD-470976 5/16 X 5/16 244 IFHD-570978 3/8 X 3/8 244 IFHD-6
Rev. 1/97
FITTINGS
X-17Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Brass Inverted Flared Fittings
Rev. 09/05
45° Elbow
Part No.Tube Size
Pipe Thread Parker No.
W'Head No.
70875 1/8" 1/8"70876 3/16" 1/8" 259-IFHD-3-270877 1/4" 1/8" 259-IFHD-4-2 352X470878 5/16" 1/8" 259-IFHD-5-2 352X570879 5/16" 1/4" 259-IFHD-3-470880 3/8" 1/8"70881 3/8" 1/4" 259-IFHD-6-4 352X670883 1/2" 3/8"
Male Elbow
Part No.Tube Size
Pipe Thread Parker No.
W'Head No.
70895 1/8" 1/8" 249-IFHD-3-270896 3/16" 1/8" 249-IFHD-3-2 402X370897 1/4" 1/8" 249-IFHD-4-2 402X470898 1/4" 1/4" 249-IFHD-4-4 402X4X470899 5/16" 1/8" 249-IFHD-5-2 402X570900 5/16" 1/4" 249-IF-6-2 402X5X470902 3/8" 1/8" 249-IF-5-470903 3/8" 1/4" 249-IFHD-6-4 402X670904 3/8" 3/8" 249-IFHD-6-670906 1/2" 3/8" 249-IFHD-8-670908 5/8" 1/2" 249-IFHD-10-8
Steel Plug
Part No.Tube Size Parker No.
W'Head No.
70917 3/16" 131X370918 1/4" 131X470919 5/16" 131X570920 3/8"
Union Elbow
Part No.Tube Size
Parker No.W'Head
No.70932 1/4"70933 5/16" 255-IFHD-470936 1/2"
FITTINGS
X-18 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Brass Inverted Flared Fittings
Male Run Tee
Part No. Tube SizePipe
Thread Parker No.W'Head
No.70942 3/16 X 3/16 1/8 252-IFHD-3-270944 1/4 X 1/4 1/870985 3/16 X 1/4 1/4
Female Branch Tee
Part No. Tube SizePipe
Thread Parker No.W'Head
No.70962 3/16 X 3/16 1/870964 1/4 X 1/4 1/870966 5/16 X 5/16 1/8 252-IFHD-5-2
See Your Sales RepresentativeAbout Our
Custom Made Assortments.Have The Proper Fitting On Hand
When You Need It!
Rev. 4/99
FITTINGS
X-19Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Brass Pipe Fittings
AdvantagesAll pipe fitting threads are made to Dryseal standards.Connectors, unions, nuts and extruded elbows and tees aremachined from CA 360 and CA 345 brass; forged elbows andtees are machined from CA 377 brass.
SpecificationsMeets functional requirements of the SAE, ASME and ASA.
ApplicationsUse with brass, copper or iron pipe. Manufactured for lowand medium pressure line connection work.
Working Pressure and Temperature RangesFrom -65° to +250°F. at 1000 psi.
VibrationFair resistance to vibration and pipe movement depending uponconditions.
SizesTube sizes are determined by the numbers of sixteenths of aninch in the tube O.D.
Dryseal Pipe Threads
Pipe threads are made to the Dryseal USA(American) - Standard Taper Pipe Thread*standard, known as the NPTF. Dryseal pipethreads, unlike other types of threads, sealjoints pressure-tight.
The dryseal pipe thread roots are wider thanthe crests. When the threads are wrenchedtogether, the roots crush the sharper crestsof the mating threads. This forms a metal-to-metal seal. Dryseal threads improve sealingcharacteristics, but a thread sealant isrecommended.
*Formerly Dryseal American (National Standard.,)
Dryseal pipe threads Regular pipe threads hand-Dryseal pipe threads wrench-tight. Seals tight. Seals joints on the
hand-tight. tightly on all sides for sides only and does notpositive sealing action. prevent spiral leakage.
Pipe Gauge
Use this gauge to measure pipe threadfittings.
Note: Pipe thread dimensions are alwaysexpressed in terms of the inside diameter ofthe pipe, thus if you measure the O. D. youmust subtract double the wall thickness toarrive at the I. D.
Rev. 8/93
FITTINGS
X-20 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Brass Pipe Fittings
Tee Union
CrossReducer Coupling
Coupling
90 Union Elbow
2200
Rev. 8/93
Part No.Pipe
ThreadParker
No.W'head
No.70502 1/4 x 1/8 208P-4-2 3300X4X270504 3/8 x 1/8 208P-6-2 3300X6X270505 3/8 x 1/4 208P-6-4 3300X6X470507 1/2 x 3/8 208P-8-6 3300X8X6
Part No.Pipe
ThreadParker
No.W'head
No.70510 1/8 2200P-2-2 3500X270512 1/4 1200P-4-4 3500X470514 3/8 2200P-6-6 3500X670516 1/2 2200P-8-8 3500X870517 3/4 3500X12
Part No.Pipe
ThreadParker
No.W'head
No.70520 1/8 2203P-2 3700X270522 1/4 2203P-4 3700X470524 3/8 2203P-6 3700X670526 1/2 2203P-8 3700X8
Part No.Pipe
ThreadParker
No.W'head
No.70530 1/8 2205P-2 3950X270532 1/4 2205P-4 3950X470534 3/8 2205P-6 3950X670536 1/2 2205P-8 3950X8
Part No.Pipe
ThreadParker
No.W'head
No.70551 1/8 3250X270552 1/4 212P-4 3250X470556 1/2 3250X8
Part No.Pipe
ThreadParker
No.W'head
No.70540 1/8 207P-2 3300X270542 1/4 207P-4 3300X470544 3/8 207P-6 3300X670546 1/2 207P-8 3300X870550 3/4 3300X12
FITTINGS
X-21Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Brass Pipe Fittings
Cap Square Head Plug
Countersunk Hex Pipe Plug Slotted Plug
BushingHex Head Plug
Part No.Pipe
ThreadParker
No.W'head
No.70595 1/8 219P-270596 1/4 219P-470597 3/8 219P-670598 1/2 219P-8
Part No.Pipe
ThreadParker
No.W'head
No.70560 1/8 213P-2 3129X270562 1/4 213P-4 3129X470564 3/8 213P-6 3129X670566 1/2 213P-8 3129X8
Part No.Pipe
ThreadParker
No.W'head
No.70704 1/8 218P-2 3152X270706 1/4 218P-4 3152X470708 3/8 218P-6 3152X670710 1/2 218P-8 3152X870711 3/4 3152X12
Part No.Pipe
ThreadParker
No.W'head
No.70570 1/8 211P-2 3151X270572 1/4 211P-4 3151X470574 3/8 211P-6 3151X670576 1/2 211P-8 3151X8
Part No.Pipe
ThreadParker
No.W'head
No.70670 1/8 220P-270672 1/4 220P-470674 3/8 220P-6
Part No.Pipe
ThreadPipe
ThreadParker
No.W'head
No.70582 1/4 1/8 209P-4-2 3220X4X270584 3/8 1/8 209P-6-2 3220X6X270585 3/8 1/4 209P-6-4 3220X6X470587 1/2 1/8 209P-8-2 3220X8X270588 1/2 1/4 209P-8-4 3220X8X470589 1/2 3/8 209P-8-6 3220X8X670590 3/4 1/4 209P-12-4 3220X12X470591 3/4 3/8 209P-12-6 3220X12X670592 3/4 1/2 209P-12-8 3220X12X8
Rev. 1/02
FITTINGS
X-22 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Brass Pipe Fittings
Close Nipple Hex Nipple
Hex Nipple ReducerLong Nipple
Street Elbow
Lock Nut
Part No.Pipe
ThreadParker
No.W'head
No.70610 1/8" 215PN-2 3326x270612 1/4" 215PN-4 3326x470614 3/8" 215PN-6 3326x670616 1/2" 215PN-8 3326x870617 3/4" 3326x12
Pipe Parker W'headPart No. Thread No. No.70602 1/4" 210p-4
Part No.Pipe
ThreadOverall Length Parker No.
W'head No.
70620 1/8" 1 1/2" 215PNL-2-15 3327X270621 1/8" 2" 215PNL-2-20 3328X270622 1/8" 2 1/2" 215PNL-2-25 3329X270623 1/8" 3" 215PNL-2-30 3330X270627 1/4" 1 1/2" 215PNL-4-15 3327X470628 1/4" 2" 215PNL-4-20 3328X470629 1/4" 2 1/2" 215PNL-4-25 3329X470630 1/4" 3" 215PNL-4-30 3330X470641 3/8" 2" 215PNL-6-20 3328X670642 3/8" 2 1/2" 215PNL-6-2570643 3/8" 3" 215PNL-6-3070650 1/2" 1 1/2" 215PNL-8-1570651 1/2" 2" 215PNL-8-2070653 1/2" 3" 215PNL-8-30 3330X8
Pipe Parker W'headPart No. Thread No. No.70715 1/8" 216P-2 3325X270717 1/4" 216P-4 3325X470719 3/8" 216P-6 3325X670721 1/2" 216P-8 3325X8
Part No.Pipe
ThreadPipe
ThreadParker
No.W'head
No.70727 1/4" 1/8" 216P-4-2 3325X4X270729 3/8" 1/8" 216P-6-2 3325X6X270730 3/8" 1/4" 216P-6-4 3325X6X470732 1/2" 1/4"70733 1/2" 3/8" 216P-8-6 3325X8X6
Female Male
Part No.Pipe
ThreadPipe
ThreadParker
No.W'head
No.70660 1/8" 1/8" 2202P-2-2 3400X270662 1/4" 1/8" 2202P-4-2 3400X4X270663 1/4" 1/4" 2202P-4-4 3400X4X270665 3/8" 3/8" 2202P-6-6 3400X670667 1/2" 1/2" 2202P-8-8 3400X8
Rev. 5/99
FITTINGS
X-23Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Brass Pipe Fittings
Adapter 45° Street Elbow
Street Tee
Branch Tee
Bulkhead Fitting
Female Male
Part No.Pipe
ThreadPipe
ThreadParker
No.W'head
No.70680 1/8" 1/8" 222-P-2-2 3200X270682 1/4" 1/4" 222-P-4-4 3200X470684 3/8" 3/8" 222-P-6-6 3200X670686 1/2" 1/2" 222-P-8-870692 1/4" 1/8" 222-P-4-2 3200X4X270694 3/8" 1/4" 222-P-6-4 3200X6X470696 1/2" 3/8" 222-P-8-6 3200X8X670698 3/4" 1/2"
Part No.Pipe
ThreadParker
No.W'head
No.70750 1/8" 2225P-2 3750X270752 1/4" 2225P-4 3750X470754 3/8" 2225P-6 3750X670756 1/2" 2225P-8 3750X8
Part No.
Pipe Thread Parker No.
W'head No.
70740 1/8" 2214P-2-2 3350X270742 1/4" 2214P-4-4 3350X470744 3/8" 2214P-6-6 3350X670746 1/2" 2214P-8-8 3350X8
Part No.
Pipe Thread Parker No.
W'head No.
70760 1/8" 2224P-2 3600X270762 1/4" 2224P-4 3600X470764 3/8" 2224P-6 3600X670766 1/2" 3600X8
Rev.04/11
*DOT Approved
Female Straight
Part No.Tube Size
Pipe Thread
Thread O.D.
Overall Length Parker No.
W'head No.
70769 1/8" 5/8-18 1.50 207ACBH-270770 1/4" 3/4-16 1.50 207ACBHS-4 W2120470772 1/4" 3/4-16 .94 207ACBH-4 W0546570773 3/8" 1.00-14 1.31 207ACBH-670774 1/2" 1-18-14 1.50 207ACBH-870775* 1/2" 3/8" 7/8-20 1-5/1670776* 3/8" 3/8" 7/8-20 1-3/8
FITTINGS
X-24 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Brass Hose Barb
AdvantagesAll Parker hose barb fitting pipe threads are made toDryseal standards. (Check specifications on those notshown above with Parker part number). Connectors,unions, nuts and extended elbows and tees are machinedfrom CA 360 and CA 345 brass.
Temperature and Working Pressure RangesFrom -40° to +160°F. at 150 psi maximum
SizesPipe sizes are determined by the number of sixteenths ofan inch in the pipe size..
Note: These fittings are intended for use with 97HC hoseclamp, similar type clamp or a crimped ferrule.
Assembly Instructions1. Cut hose cleanly and squarely to length.2. Slide clamp on hose.3. Lubricate hose. Push hose on fitting until hose bottoms
against stop ring or hex.4. Position hose clamp as shown below and secure with a
screwdriver or wrench. Maintain "A" dimension noted belowfor proper clamp positioning.
Rev. 8/93
Hose Hose ASize Clamp3/16" 97 HC-3 1/4"1/4" 97 HC-3 1/4"
5/16" 97 HC-6 1/4"3/8" 97 HC-6 1/8"1/2" 97 HC-8 1/8"5/8" 97 HC-12 1/8"3/4" 97 HC-12 1/8"
FITTINGS
X-25Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Brass Hose Barb Fittings
Rev. 09/12
Hose Mender
Part No. Tube SizeParker
No.W'head
No.72210 1/872211 3/16 122HB-372212 1/4 122HB-472213 5/16 122HB-572214 3/8 122HB-672216 1/2 122HB-872217 5/872218 3/4
Hose Barb to Male Pipe
Part No.Tube Size
Pipe Thread Parker No.
W'head No.
72150 1/8 1/872155 3/16 1/8 125HBL-3-272156 3/16 1/472160 1/4 1/8 125HBL-4-272161 1/4 1/4 125HBL-4-472162 1/4 3/8 125HBL-4-672163 1/4 1/272167 5/16 1/8 125HBL-5-272168 5/16 1/4 125HBL-5-472169 5/16 3/872175 3/8 1/8 125HBL-6-272176 3/8 1/4 125HBL-6-472177 3/8 3/8 125HBL-6-672178 3/8 1/272185 1/2 1/4 125HBL-8-472186 1/2 3/8 125HBL-8-672187 1/2 1/2 125HBL-8-872188 1/2 3/4 125HBL-8-1272195 5/8 3/8 125HBL-10-672196 5/8 1/2 125HBL-10-872197 5/8 3/472200 3/4 3/872201 3/4 1/2 125HBL-12-872202 3/4 3/4 125HBL-12-12
Hose Barb to Female Pipe
Part No. Tube SizePipe
Thread Parker No.W'head
No.72100 1/4 1/8 126HBL-4-272101 1/4 1/4 126HBL-4-272103 5/16 1/4 126HBL-4-272105 3/8 1/8 126HBL-4-272106 3/8 1/4 126HBL-4-272107 3/8 3/8 126HBL-4-272110 1/2 3/8 126HBL-4-272111 1/2 1/2 126HBL-4-2
Hose Barb to Male Pipe
Part No. Hose ID Male NPT72115 1/4" 1/8"72116 1/4" 1/4"72117 1/4" 3/8"72120 3/8" 1/8"72121 3/8" 1/4"72122 3/8" 3/8"72125 1/2" 3/8"
Part No. Hose ID72270 1/4"72271 3/8"72272 1/2"72273 5/8"72274 3/4"
Hose Barb Tee
FITTINGS
X-26 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Brass Hose Barb Fittings
Hose Barb 45°
Hose PipePart No Size Thread72141 1/4" 1/4"72180 5/8" 1/2"
72181 3/4" 1/2"
Part No Hose SizePipe
Thread
Beaded Hose Barb45° Elbow to Male Pipe
Beaded Hose BarbStraight to Male Pipe
72205 1/2" 1/2"72206 1/2" 1/4"72208 5/8" 3/8"72209 5/8" 1/2"72199 3/4" 1/2"
Part No Hose SizePipe
Thread
Hose Barbto SAE Flared Swivel
Tube PipePart No Size Thread72239 1/4" 5/16"
72232 1/2" 1/4"72237 1/2" 1/2" 269HB-8-872233 5/8" 1/4" 269HB-10-472234 5/8" 3/8" 269HB-10-672235 5/8" 1/2" 269HB-10-872236 3/4" 1/2" 269HB-12-8
Part No Tube SizePipe
ThreadParker No.
Beaded Hose Barb90° Elbow to Male Pipe
72220 1/4" 1/8" 129HB-4-272221 1/4" 1/4" 129HB-4-472223 5/16" 1/4" 129HB-5-472225 3/8" 1/8" 129HB-6-272226 3/8" 1/4" 129HB-6-472227 3/8" 3/8" 129HB-6-672230 1/2" 3/8" 129HB-8-6
Part No. Tube SizePipe
ThreadParker No.
Hose Barb90° Elbow to Male Pipe
Rev. 08/05
FITTINGS
X-27Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Brass Ball Valves & Plug Valves
Plug Valve(Female Pipe to Male Pipe)
Plug Valve(Female Pipe to Female Pipe)
Ball Valve Plug Valve(Male Pipe to Male Pipe)
Rev. 03/10
Pipe Parker W'headPart No Thread No. No.72263 1/8" PV607-272264 1/4" PV607-4
Pipe Parker W'headPart No Thread No. No.72266 1/8" PV609-272267 1/4" PV609-4
Pipe Parker W'headPart No Thread No. No.72260 1/8" PV608-272261 1/4" PV608-4
Pipe Parker Part No Thread No. 72240 1/4" V500P-4 USA72241 3/8" V500P-6 USA72242 1/2" V500P-8 USA72243 3/4" V500P-12 USA72244 1" V500P-16 USA
Part No. Pipe Thread Description
72284 1/4" Italy72285 3/8" Italy72286 1/2" Italy72287 3/4" Italy72288 1" Italy72289 1-1/4" Italy
FITTINGS
X-28 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Brass Truck Valves
Truck Valve(Hose to Male Pipe)
Truck Valve(Flare to Male Pipe)
Truck Valvew/Removable Hose Barb
(Hose to Male Pipe)
Truck Valve(Female Pipe to Male Pipe)
Part No.Hose I.D.
Pipe Thread Parker No.
W'head No.
72250 3/8 3/8 V404P-6-6 750672251 5/8 3/8 V404P-10-6 750472253 5/8 1/2 750272254 3/4 1/2
Part No.Hose I.D.
Pipe Thread Parker No.
W'head No.
72275 1/2 1/2 V409F-8-872276 5/8 1/2 V409F-10-872277 3/4 1/2 V409F-12-8
Part No. Hose I.D.
Pipe Thread Parker No.
W'head No.
72255 5/8 1/2 SV404P-10-872256 3/4 1/2 SV404P-12-8
Part No. Hose I.D.
Pipe Thread Parker No.
W'head No.
72280 3/8 3/8 V405P-6-672281 1/2 1/2 V405P-8-8
Rev. 10/12
FITTINGS
X-29Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Drain Cock AdvantagesBoth external-seat and internal-seatdrain cocks are manufactured to thehighest quality standards. Hand-tightening provides ametal-to-metal seal.
Ground Plug Shutoff Cock AdvantagesThese economical valves are available in several styles.Brass castings or forged bodies for extra strength.
ApplicationsManufactured for use with low pressure air, water, gas andcertain other fluids. (Note: lubricant may not be compatiblewith some fluids. Contact factory for special fluid require-ments.)
Brass Drain Cocks, Shutoff Cocks, etc.
Working Pressure RangesSystem temperature and the type of tubing used should beconsidered. Ground plug shutoffs are designed to withstand30 PSI working pressure, except where noted.
NomenclaturePart numbers are constructed from symbols that identify thestyle and size of the fitting. The first series of numbers andletters identifies the style and type fitting. The second seriesof numbers describes the size.
SizesTube sizes are determined by the number of sixteenths of aninch in the tube O.D.
Rev. 05/06
Pipe Parker W'headPart No. Thread No. No.71021 1/4-18 DC606-4 6788
External Seal Drain Cock
Pipe Parker W'headPart No. Thread No. No.71000 1/8 DC603-271002 1/4 DC603-4
Drain Cock Bib Drain Valve
Hose Pipe Parker W'headPart No. Size Thread No. No.71007 3/8 1/4 DC607-4 120
External Seal Drain Cock
Pipe Parker W'headPart No. Thread No. No.71035 1/8 DC604-2 13571037 1/4 DC604-4 14571039 3/8 DC604-6 155-27071041 1/2 160
FITTINGS
X-30 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Brass Drain Cocks, Shutoff Cocks, etc.
Rev. 05/06
Drain Cock
Pipe Parker W'headPart No. Thread No. No.71012 1/8 DC601-2 689171014 1/4 DC601-4 689271016 3/8 DC601-6 689371018 1/2 DC601-8 AN44P
Ground Plug Shutoff Cock(Compression to Male Pipe)
Hose Pipe Parker W'headPart No. Size Thread No. No.71101 1/4 1/8 V304C-4-271102 5/16 1/4
Ground Plug Shutoff Cock(Female Pipe to Male Pipe)
Hose Pipe Parker W'headPart No. Size Thread No. No.71114 1/8 1/8 V402P-2-2 682471115 1/4 1/4 V402P-4-4 6829-49P71116 3/8 3/8 V402P-6-6
Ground Plug Shutoff Cock(Female Pipe to Female Pipe)
Female Parker W'headPart No. Pipe No. No.71125 1/8 V403P-2-271105 1/4 V403P-4-4 6809
FITTINGS
X-31Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
NTA AdvantagesMeets D.O.T. FMVSS 571.106 air brake specifications.Utilizes ribbed sleeve for compression and positive grip.Bodies (less tube supports) are interchangeable with AB(SAE J246) fitting bodies.
No Special Tools NeededYou can assemble tubing to NTA fittings, no need to flare.Machined from CA 360, CA 345 or CA 377 brass. Broadselection of styles available.
SpecificationsMeets functional requirements of the SAE automotive tubefitting standards: SAE J246 and SAE J1131.
ApplicationsUse with SAE J844 Type 3A and 3B nylon tubing in airbrake systems or in cab air controls.
Assembly Instructions1. Cut tubing squarely.2. Insert tubing into fitting until bottomed on seat.3. Tighten nut with wrench until one thread remains visible
on the fitting body; or, the nut should be screwed downfinger-tight, then wrench-tightened as indicated in the
following table (this will allow for a number of remakes):
SizesTube sizes are determined by the numbers of sixteenths ofan inch in the tube O.D.
TUBE SIZE is expressed in terms of the outsidediameter of the tube. (O.D.) Refer to table to matchtube size with fitting diameter and threads per inch.
For Nylon TubingBrass Air Brake-NTA® Fittings
AdditionalTube Number of turnsSize from Hand-Tight1/4 3
3/8 and 1/2 45/8 and 3/4 3-1/2
TABLE OF THREADSTube Thread ThreadsSize Size Per Inch1/4 7/16 243/8 17/32 241/2 11/16 205/8 13/16 183/4 1 18
Rev. 07/06
72301 1/4 PFT-4A-BLK Black 1'72301-100 1/4 PFT-4A-BLK Black 100'
72304 3/8 PFT-6B-BLK Black 1'72304-100 3/8 PFT-6B-BLK Black 100'
72306 1/2 PFT-8B-BLK Black 1'72306-100 1/2 PFT-8B-BLK Black 100'
72308 5/8 PFT-10B-BLK Black 1'72308-50 5/8 PFT-10B-BLK Black 50'
72310 3/4 PFT-12B-BLK Black 1'72310-50 3/4 PFT-12B-BLK Black 50'
72305 1/2 Red 1'72305-100 1/2 Red 100'
72307 1/2 Blue 1'72307-100 1/2 Blue 100'
LengthPart No.Tubing
O.D.Parker
No.Color
Working Pressure RangesUp to 150 psi.
Temperature RangesFittings will withstand variations from -40° to +200° F.
Nylon Tubing
Heat and light stabilized seamless extruded nylon core reinforcedwith one open ply of fibrous reinforcement and a protective nyloncover sheath. The outer cover and core are fused to minimizeleakage and maximize impact resistance and are always of con-trasting colors.
This tubing conforms to SAE specification J844 type B.The B refers to reinforced tubing.
Temperature Range: -40°F to +200°F (-40°C to +93°C). -70°F to+200°F (-56.6°C to +93°C) for PFT-8B coiled air brake tubing.
Maximum Working Pressure: 150 PSI.
Meets D.O.T. FMVSS 106.
FITTINGS
X-32 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.Rev. 1/99
For Nylon TubingBrass Air Brake-NTA® Fittings
NTA Sleeve
NTA Nut
Stainless Steel Insert
NTA Union
Tube Parker W'headPart No. Size No. No.71582 1/4 63NTA-4 1484X471584 3/8 63NTA-6 1484X671586 1/2 63NTA-8 1484X871587 5/8 63NTA-10 1484X1071588 3/4 63NTA-12 1484X12
Tube Parker W'headPart No. Size No. No.71552 1/4 62NTA-4 1462X471554 3/8 62NTA-6 1462X671556 1/2 62NTA-8 1462X871557 5/8 62NTA-10 1462X1071558 3/4 62NTA-12 1462X12
Female Parker W'headPart No. Pipe No. No.71541 3/16 61NTA-371542 1/4 61NTA-4 1461X471544 3/8 61NTA-6 1461X671546 1/2 61NTA-8 1461X871547 5/8 61NTA-10 1461X1071548 3/4 61NTA-12 1461X12
Female Parker W'headPart No. Pipe No. No.71501 3/16 60NTA-371502 1/4 60NTA-4 1460X471504 3/8 60NTA-6 1460X671506 1/2 60NTA-8 1460X871507 5/8 60NTA-10 1460X1071508 3/4 60NTA-12 1460X12
FITTINGS
X-33Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Brass Air Brake-NTA® FittingsFor Nylon Tubing
NTA 90O Male Elbow
NTA Male Connector Tube Male Parker W'headPart No. O.D. Pipe No. No.71512 3/16 1/16 68NTA-3-171513 3/16 1/8 68NTA-3-271514 3/16 1/4 68NTA-3-471515 1/4 1/8 68NTA-4-2 1468X471516 1/4 1/4 68NTA-4-4 1468X4X471517 1/4 3/8 68NTA-4-6 1468X4X671518 3/8 1/8 68NTA-6-2 1468X6X271519 3/8 1/4 68NTA-6-4 1468X671520 3/8 3/8 68NTA-6-6 1468X6X671521 3/8 1/2 68NTA-6-8 1468X6X871522 1/2 1/4 68NTA-8-4 1468X8X471523 1/2 3/8 68NTA-8-6 1468X871524 1/2 1/2 68NTA-8-8 1468X8X871525 1/2 3/4 1468X8X1271526 5/8 3/8 68NTA-10-6 1468X10X671527 5/8 1/2 68NTA-10-8 1468X1071528 5/8 3/4 1468X10X1271529 3/4 1/2 68NTA-12-8 1468X1271530 3/4 3/4 68NTA-12-12 1468X12X12
Rev. 11/04
71560 3/16 1/8 269NTA-3-271561 3/16 1/4 269NTA-3-471562 1/4 1/8 269NTA-4-2 1469X471563 1/4 1/4 269NTA-4-4 1469X4X471564 1/4 3/8 269NTA-4-6 1469X4X671565 3/8 1/8 269NTA-6-2 1469X6X271567 3/8 1/4 269NTA-6-4 1469X671569 3/8 3/8 269NTA-6-6 1469X6X671570 3/8 1/2 269NTA-6-8 1469X6X871571 1/2 1/4 269NTA-8-4 1469X8X471572 1/2 3/8 269NTA-8-6 1469X871574 1/2 1/2 269NTA-8-8 1469X8X871575 5/8 3/8 269NTA-10-6 1469X10X671576 5/8 1/2 269NTA-10-8 1469X1071577 5/8 3/4 1469X10X1271579 3/4 1/2 269NTA-12-8 1469X12
W'head No.
Part No.Tube Size
Pipe Thread
Parker No.
FITTINGS
X-34 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
For Nylon TubingBrass Air Brake-NTA® Fittings
NTA Female Connector
NTA Female Elbow
NTA Union Elbow
NTA 45° Male Elbow
Rev. 1/02
Tube Pipe Parker W'headPart No. O.D. Thread No. No.71613 1/4 1/8 270NTA-4-2 1470X471614 3/8 1/4 270NTA-6-4 1470X671615 3/8 3/8 270NTA-6-6 1470X6X671616 1/2 3/8 270NTA-8-6 1470X8
Tube Pipe Parker W'headPart No. O.D. Thread No. No.71593 3/8 1/8 66NTA-6-2 1466X6X271594 3/8 1/4 66NTA-6-4 1466X671595 3/8 3/8 66NTA-6-6 1466X6X671596 1/2 3/8 66NTA-8-6 1466X871597 3/4 1/2 1466X12
Tube Parker W'headPart No. Size No. No.71589 1/4 265NTA-4 1465X471590 3/8 265NTA-6 1465X671591 1/2 265NTA-8 1465X871592 5/8 265NTA-10 1465X10
Tube Pipe Parker W'headPart No. O.D. Thread No. No.71639 1/4 1/8 279NTA-4-2 1480X471638 1/4 1/4 279NTA-4-4 1480X4X471640 3/8 1/4 279NTA-6-4 1480X671641 3/8 3/8 279NTA-6-6 1480X6X671642 1/2 1/4 1480X8X471643 1/2 3/8 279NTA-8-6 1480X871644 1/2 1/2 279NTA-8-8 1480X8X871645 5/8 1/2 279NTA-10-8 1480X10
FITTINGS
X-35Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP. Rev. 01/12
For Nylon TubingBrass Air Brake-NTA® Fittings
NTA Male Branch Tee
NTA Male Run Tee
NTA Union Tee
NTA Bulkhead Union
"A" "B" "C"Tube Pipe Tube Parker W'head
Part No. O.D. Thread O.D. No. No.71617 3/16 1/8 3/16 272NTA-3-271618 1/4 1/4 1/4 272NTA-4-471619 1/4 1/8 1/4 272NTA-4-2 1472X471620 3/8 1/8 3/8 272NTA-6-2 1472X6X6X271621 3/8 1/4 1/4 1472X6X4X471622 3/8 1/4 3/8 272NTA-6-4 1472X671623 3/8 3/8 3/8 272NTA-6-6 1472X6X6X671624 1/2 3/8 1/2 272NTA-8-6 1472X871625 1/2 3/8 3/8 1472X8X6X671626 5/8 1/2 5/8 272NTA-10-8 1472X10X10X8
"A" "B" "C"Tube Tube Tube Parker W'head
Part No. O.D. O.D. O.D. No. No.71598 1/4 1/4 1/4 264NTA-4 1464X471600 3/8 1/4 3/8 1464X6X6X471601 3/8 3/8 3/8 264NTA-6 1464X671602 3/8 1/2 3/8 1464X6X6X871603 1/2 1/2 1/2 264NTA-8 1464X871605 1/2 3/8 1/2 1464X8X8X6
A
B
A
C
B
C
A
B
Tube Female Parker W'headPart No. Size Pipe No. No.71629 1/4 62NBH-4 1474X471630 3/8 62NBH-6 1474X671631 1/2 62NBH-8 1474X871632 5/8 1474X1070775 1/2 3/870776 3/8 3/8
70775 & 70776
C
"A" "B" "C"Tube Tube Pipe Parker W'head
Part No. O.D. O.D. Thd No. No.71606 1/4 1/4 1/8 271NTA-4-2 1471X471607 3/8 1/4 1/4 1471X6X4X471608 3/8 3/8 1/4 271NTA-6-4 1471X671609 3/8 3/8 3/8 271NTA-6-6 1471X6X6X671610 1/2 1/2 3/8 271NTA-8-6 1471X871612 5/8 5/8 1/2 271NTA-10-8
FITTINGS
X-36 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
72299 5/32 1'72299-100 5/32 100'
72300 1/8 1'72300-100 1/8 100'
72302 3/16 1'72302-100 3/16 100'
LengthPart No.Tubing
O.D.
Transmission Shifter Line Fittings
Rev. 07/06
Split SleeveNut Union
Male Connector Male Elbow
Nylon Tubing
Tube PipePart No. Size Thread71660 1/8" 1/16"71661 1/8" 1/8"71667 5/32" 1/8"
Tube PipePart No. Size Thread71658 1/8" 1/16"71659 1/8" 1/8"71665 5/32" 1/16"71666 5/32" 1/8"
TubePart No. Size71657 1/8"71664 5/32"
TubePart No. Size71655 1/8"71662 5/32"
TubePart No. Size71656 1/8"71663 5/32"
*72302 (3/16" Nylon Tubing) goes with partson pages X-32 thru X-35.
Heat and light stabilized seamless single wall extruded nylon tubing,available in sizes 1/8 (-2), 5/32 (-2.5), 3/16 (-3), 1/4 (-4) and 5/16 (-5).This tubing conforms to SAE specification J844 type A.The A refers to nonreinforced tubing.
Temperature Range: -40°F to +200°F (-40°C to +93°C).Maximum Working Pressure: 150 PSI.
Meets D.O.T. FMVSS 106 (Sizes 2 and 2.5 not listed in FMVSS 106).
FITTINGS
X-37Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
MPT Hose End
Air Brake Hoses & FittingsRubber Air Brake Hose
HoseSleeve
HoseMenderNut
Gladhand Seal
• Designed to repair 3/8" I.D. Air Brake Line• Fast & Economical• 5/16" hex key required to complete installa-
tion
Rev. 02/10
Part No. Description71670 Black71671 Red71672 Blue
Hose NPTFPart No. I.D. Size71825 3/8" 3/8"71826 3/8" 1/2"
Adp. w/Spring Adp. Hose End Tube PipePart No. Part No. Size Thread71800 71805 3/8" 1/4"71801 71806 3/8" 3/8"71802 71807 3/8" 1/2"71803 71808 1/2" 3/8"71804 71809 1/2" 1/2"
Hose HosePart No. I.D. O.D.71798 3/8 3/471799 1/2 7/8
Tube PipePart No. Size Thread71820 3/8 1/471821 3/8 3/871822 1/2 3/871823 1/2 1/2
Tube Sleeve Nut MenderSize Part No. Part No Part No3/8 71815 71817 718101/2 71816 71818 71811
Adapterwith Spring
AdapterHose End
Air Brake Line Air Brake Line
Field Installation Kit Hose & Tubing Spacer
Hose I.D. PartA B No.1/2 1/2 718271/2 3/8 718283/8 3/8 71829
• UV Resistant. • Low Temp and impact resistant.
A B
(2 fittings included in kit)
FITTINGS
X-38 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Male Connector
D.O.T. Push-In Air Brake Fittings
• Designed for all D.O.T truck and trailer applications• Meet D.O.T. FMVSS 571.106 Air Brake Performance Specifications.• No special tools needed. Just bottom tubing in fitting body for positive seal.• Meet Hot Pull requirements of SAE J1131 when used with included tube support• Working pressure from 27in. Hg vacuum to 250 psi (except for composite ftgs.)• Working temperature from -40° F. to +200° F (except for composite fittings.)• BUNA N (Nitrile) O-Rings.
Assembly Instructions:
1. Cut tubing off squarely. Be certain the port or matingpart is clean and free of debris.
2. Insert tubing into fitting until it bottoms. Pull on tubing toverify it is properly retained in the fitting.
3. To disassemble, simply hold release button against thebody and remove tubing.
D.O.T. Push-in Air Brake Fittings
Union Tee
Male Elbow
Rev.12/12
* Not to be used in environments exceeding 145psi or 140 degrees F. DOT FMVSS49CFR571-106 prohibits use of composite fittings between towed and towingvehicles or between a driveshaft and chassis.
Tube Parker Composite*Part No. Size No. No.71930 1/4" 62PMT-4 71930P71931 3/8" 62PMT-6 71931P71932 1/2" 62PMT-8 71932P71933 5/8" 62PMT10 71933P71934 3/4" 62MT12
Union
Part Tube Pipe Parker Composite*No. Size Thread No. No.
71944 1/4" 1/8" 68PM-4-2 71944P71945 1/4" 1/4" 68PM-4-4 71945P71946 1/4" 3/8" 68PM-4-671948 3/8" 1/4" 68PM-6-4 71948P71949 3/8" 3/8" 68PM-6-6 71949P71950 3/8" 1/2" 68PM-6-871952 1/2" 3/8" 68PM-8-6 71952P71953 1/2" 1/2" 68PM-8-871960 5/8" 1/2" 68PM-10-871961 3/4" 1/2" 68PM-12-8
Part No.
Tube SizePipe
ThreadParker No.
Composite* No.
71970 1/4" 1/8" 169MNS-4-2 71970P71971 1/4" 1/4" 169MNS-4-4 71971P71972 1/4" 3/8" 169MNS-4-671974 3/8" 1/4" 169MNS-6-4 71974P71975 3/8" 3/8" 169MNS-6-6 71975P71976 3/8" 1/2" 169MNS-6-871977 1/2" 1/4" 169MNS-8-471978 1/2" 3/8" 169MNS-8-6 71978P71979 1/2" 1/2" 169MNS-8-871981 5/8" 1/2" 169MNS-10-8
Tube ParkerPart No. Size No.71954 1/4" 164PM-471955 3/8" 164PM-671956 1/2" 164PM-8
FITTINGS
X-39Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Steel 37 JIC Adapters
Male Adapter
Straight Thread Adapter
Part No. T1 (UNF) Dash Size76034 7/16-20 476035 1/2-20 576036 9/16-18 676038 3/4-16 876040 7/8-14 1076042 1 1/16-12 1276044 1 3/16-12 1476046 1 5/16-12 1676048 1 5/8-12 20
JIC Plug
X-38aRev.10/07
Part No. Tube Size T1 (UNF) Dash Size76004 1/4 7/16-20 476005 5/16 1/2-20 576006 3/8 9/16-18 676008 1/2 3/4-16 876010 5/8 7/8-14 1076012 3/4 1 1/16-12 1276014 7/8 1 3/16-12 1476016 1 1 5/16-12 1676020 1 1/4 1 5/8-12 20
JIC Cap
90° Male Elbow
Union
Straight Thread90°Elbow
Part No. Pipe Thread Straight Thread Tube Size77073 18-27 7/16-20 1/477078 1/4-18 9/16-18 3/877082 3/8-18 3/4-16 1/277083 1/2-14 3/4-16 1/277086 1/2-14 7/8-14 5/877089 3/4-14 1-1/16-12 3/4
Part No. Pipe Thread Straight Thread Tube Size77052 18-27 7/16-20 1/477056 1/4-18 9/16-18 3/877060 1/2-14 3/4-16 1/277064 1/2-14 7/8-14 5/877067 3/4-14 1-1/16-12 3/4
Part No. Pipe Thread Straight Thread Tube Size78052 7/16-20 7/16-20 1/478053 9/16-18 7/16-20 1/478056 3/4-16 9/16-18 3/878057 9/16-18 3/4-16 1/278058 3/4-16 3/4-16 1/2
Part No. Pipe Thread Straight Thread Tube Size78002 7/16-20 7/16-20 1/478008 9/16-18 3/4-16 3/878010 3/4-16 9/16-18 1/278011 3/4-16 3/4-16 1/278012 3/4-16 7/8-14 1/2
Part No. Straight Thread Tube Size77205 7/16-20 1/4 #477207 1/2-20 5/16 #577210 9/16-18 3/8 #677213 3/4-16 1/2 #877217 7/8-14 5/8 #1077222 1 1/16-12 3/4 #12
FITTINGS
X-40 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.X-38b
Hose & Truck Fittings
Inner Tube: NitrileReinforcement: 1 Fiber Braid - 1 Steel BraidCover: Fiber Braid
Meets SAE J1402 All and D. O.T. FMVSS 106 All Brake hoserequirements.
Application: Medium pressure service with the following:
Petroleum Base Hydraulic Fluids"Water-glycol" and "Water-Oil" Fire Resistant Hydraulic FluidsWaterCrude and Fuel OilsHot OilDiesel FuelsGasolineAnti-Freeze SolutionsAir
Temp. Range:Hydraulic: -40°F to +212°F (-40°C to +100°C);Air Brake: -40°F to +200°F (-40°C to +93°C);Hot Oil: -40°F to +250°F (-40°C to +121°C);
Truck Hose(Steel Reinforced)
ReusableFemale JIC 37° Swivel
*These fittings contain a dual seatthat accepts both the JIC (37°) andSAE (45°) male configurations.
Rev. 12/12
H069 SeriesMaximum Minimum Minimum
Hose Hose Working Burst BendPart No. No. I. D. Pressure Pressure Radius72350 4 3/16 3,000 12,000 3"72352 5 1/4 3,000 12,000 3-3/8"72354 6 5/16 2,250 9,000 4"72356 8 13/32 2,000 8,000 4-5/8"72358 10 1/2 1,750 7,000 5-1/2"72360 12 5/8 1,500 6,000 6-1/2"
H213 SeriesMaximum Minimum Minimum
Hose Hose Working Burst BendPart No. No. I. D. Pressure Pressure Radius72500 4 3/16 2,000 8,000 3/4"72502 6 5/16 1,500 6,000 1-1/4"72503 8 13/32 1,250 5,000 1-3/4"72504 10 1/2 1,000 4,000 2-1/4"
'Note: #6 fittings come in 2 different thread sizes.
Hose Hose Hose Fem. JICPart No. No. Part No. I. D. Thread72370* 4 72350 3/16 7/16-2072371* 5 72352 1/4 1/2-2072372' 6 72354 5/16 9/16-1872373' 6 72354 5/16 5/8-1872374* 8 72356 13/32 3/4-1672376* 10 72358 1/2 7/8-1472378 12 72360 5/8 1-1/16-12
Hose Hose Hose Fem. JICPart No. No. Part No. I. D. Thread72507* 4 72500 3/16 7/16-2072508' 6 72502 5/16 9/16-1872510' 6 72502 5/16 5/8-1872511* 8 72503 13/32 3/4-1672512* 10 72504 1/2 7/8-14
FITTINGS
X-41Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Swing Couplings
X-39Rev. 06/05
Part No. Description72560 1/4" Series B1 Protective Boot72561 3/8" Series E Protective Boot72562 1/2" Series H Protective Boot
Features
B1 In accordance with safety standard ISO 4414, EN 983, Model in accordance with ISO 6150-B-12, AFNOR: B-12NF E 49-053 and US: MIL-C-4109, Full flow, negligible loss of pressure, Simple operation, no force required,
Compact design, Det Norske Veritas Type approval no. P-10819
E In accordance with safety standard ISO 4414, EN 983, Model in accordance with ISO 6150-B-15, AFNOR: B-15NF E 49-053 and US: MIL-C-4109, Full flow, negligible loss of pressure, Simple operation, no force required,
Compact design, Det Norske Veritas Type approval no. P-10819
H In accordance with safety standard ISO 4414, EN 983, Model in accordance with ISO 6150-B-17, AFNOR: B-17NF E 49-053 and US: MIL-C-4109, Full flow, negligible loss of pressure, Simple operation, no force required,
Compact design, Det Norske Veritas Type approval no. P-10819
Accessories
Part No. Description SC SeriesFigure Ref.
Pg X-4072520 NPT 1/4" Female Thread A1 140 72320 B72521 NPT 3/8" Female Thread A1 141 SP7-141 B72522 NPT 1/4" Male Thread A1 142 72322 B72530 NPT 1/4" Female Thread B1 150 72330 A72531 NPT 3/8" Female Thread B1 151 72331 A72532 NPT 1/4"Male Thread B1 152 72332 A72533 NPT 3/8" Male Thread B1 155 72333 A72538 HB 3/8" Hose Barb B1 156 SP7-156 A72540 NPT 1/4" Female Thread E 582 72338 A72541 NPT 3/8" Female Thread E 580 SP7-580 A72545 NPT 3/8" Male Thread E 581 SP7-581 A72548 HB 3/8" Hose Barb E 586 SP7-586 A72551 NPT 1/2" Female Thread H 120 72380 F 72554 NPT 1/2" Male Thread H 122 72382 F
Cross Reference Coil Hose NEIA
Part No. Description72565 Series A1, B1 Cover72566 Series E Cover
FITTINGS
X-42 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Service Air Hose & Fittings
X-40 Rev. 02/10
Air Hose CouplersFemale Pipe Threads
Air Hose CouplersMale Pipe Threads
Air Hose NipplesFemale Pipe Threads
Air Hose NipplesMale Pipe Threads
NEIA Thread NPT Bore COILPart No. Type Size Size Description Figure HOSE LINCOLN MILTON PARKER SCHRADER TRU-FLATE72319 F 1/4" 1/4" Auto. Coupler B 77572320 F 1/4" 1/4" Coupler B 140 862 775 53 3526 13-33472322 M 1/4" 1/4" Coupler B 142 776 52 13-32472330 F 1/4" 1/4" Coupler A 150 632004 715 23 5142-12 13-23472332 M 1/4" 1/4" Coupler A 152 631004 716 22 5141-12 13-22472347 F 1/4" 1/4" Long Coupler C 170 815 790 73 3528 13-43472331 F 3/8" 1/4" Coupler A 151 632006 718 23E 5263-12 13-25472333 M 3/8" 1/4" Coupler A 155 631006 719 22E 4006-12 13-24472338 F 1/4" 3/8" Coupler A 582 642004 1833 25C 6104-1272380 F 1/2" 1/2" Coupler F 120 1815 B37 3512 13-71272382 M 1/2" 1/2" Coupler F 122 1816 B36 13-70472390 F 1/4" 1/4" Coupler D 160 78572400 F 1/4" 3/8" Coupler E 592 1803 15C72401 F 3/8" 3/8" Coupler E 590 1805 15
Industrial ARO Automotive Parker/
Style Industrial Style Truflate
NEIA Thread NPT Bore COILPart No. Type Size Size Description Figure HOSE LINCOLN MILTON PARKER SCHRADER TRU-FLATE72326 M 1/4" 1/4" Nipple B 1401 13329 777 A2C 3529 12-32472324 F 1/4" 1/4" Nipple B 1402 13331 778 A3C 3530 12-33472336 M 1/4" 1/4" Nipple A 1501 630104 727 HC 5138-11 12-22472334 F 1/4" 1/4" Nipple A 1502 630204 728 H3C 5139-11 12-23472346 M 1/4" 1/4" Long Nipple C 1701 11659 791 L2C 3531 12-42472348 F 1/4" 1/4" Long Nipple C 1702 11661 792 L3C 3532 12-43472335 F 3/8" 1/4" Nipple A 1505 630206 732 H3C-E 4106-11 12-23672337 M 3/8" 1/4" Nipple A 1503 630106 733 H2C-E 5263-11 12-22672339 M 1/4" 3/8" Nipple A 5803 640104 1839 H0E 6004-1172328 F 1/4" 3/8" Nipple A 5804 HIE 6104-1172329 HB 3/8" 3/8" Nipple B 5806 H5E 6206-1172381 M 1/2" 1/2" Nipple F 1201 1857 H2F 12-75272383 M 3/8" 1/2" Nipple F 1203 1859 H0F72384 F 3/8" 1/2" Nipple F 1204 1860 H1F72385 F 1/2" 1/2" Nipple F 1202 1858 H3F72391 M 1/4" 1/4" Nipple D 1601 78372392 F 1/4" 1/4" Nipple D 1602 78472405 F 3/8" 3/8" Nipple E 5902 1808 3E72406 M 1/4" 3/8" Nipple E 5903 1809 0E72407 M 3/8" 3/8" Nipple E 5901 1807 2E
FITTINGS
X-43Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Typhoon®
High Volume Blow Gun
•Comes standard with High Flow Tip•34 CFM at 125 PSI•2.1 lbs. of Thrust OSHA
Compliant
Service Air Hose & Fittings
X-41aX-41aX-41aX-41aX-41aX-41aRev.11/08
Shop Air Hose Coil Air Hose
TubePart No. Size Length72312 1/4" 25 ft.
Pipe
Part No. Thread72295 1/8"72297 1/4"
Air Tank Valve
Extensions onlyTyphoon® Blow Gun
Part No. Description72585 24"72587 48"72590 Extension Coupling
Part No. Description72580 Blow Gun72581 Blow Gun with 24" Extension72582 Blow Gun with 48" Extension
Tube
Part No. Size Length72317 3/8" 25 ft.72318 3/8" 50 ft.
Flexzilla Hoses
Temperature Range (-40 to 150 degrees F)300 PSI working pressureReinforced bend restrictorExcellent Abrasion resistanceSuperior bend radiusLightweight and easy to handle
Flexzilla Shop Air HosePart No. 72316
Flexzilla Truck Tire Inflator HosePart No. 72313
3/8 in. ID x 50 ft Flexzilla air hoseGlad-hand attachment30 degree dual air chuck
3/8 in. ID x 50 ft Flexzilla air hose
FITTINGS
X-44 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.X-41b Rev. 02/11
Air Chuck
Part No. 72290 Part No. 72291With Clip
Extension Chuck
Part No. 72292
Service Air Hose & Fittings
Service Gages (10 to 160 lbs.)Part No. 72294
Regular Extension Service Gage (D.H. Chuck withStraight Foot for the newer style Inner Duals)
Part No. 72293
Dual Head Straight Foot Air Chuck for InnerDuals, with Lock on Threads Both Ends 1/4"
NPT
Window Inflator GagePart No. 72298
• 10 lbs. to 120 lbs. in 2 lb. increments.• Heavy duty construction.• Long service life even with constant use.• Equipped with magnifying lens for full view.• Complete with dual head chuck.• 15" Hose.• Made in the U.S.A.
FITTINGS
X-45Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Ball Swivel Fittings
Part No. 72387 Aro Series #140Part No. 72388 Industrial Series # 150
Brass Hose FerrulesEconomical and dependable brass ferrules enable
you to make up custom hose assemblies.
Service Air Hose & Fittings
Lever Blow Gun
PipePart No. Thread72345 1/4"
Blo-Guns 1/4" NPTIncludes 2 nozzles, Safety and Non-Safety
Rubber Tip
Part No. Description72343 Blo-Gun with 4' Alum Extension72344 Blo-Gun with 2' Alum Extension
X-41cRev. 10/12
Fits Hose Part No. ID Length OD72440 .500 1"72441 .525 1" 1/2"72442 .562 1" 9/16"72443 .593 1" 19/32"72444 .625 1" 5/8"72445 .656 1" 21/32"72446 .687 1" 11/16"72447 .718 1" 23/32"72448 .750 1" 3/4"
FITTINGS
X-46 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Hydraulic Brake Line & Fittings
Coupling UnionFits European Bubble Flare
Domestic No-KinkBrake Line
Double Flared End
European No-KinkBrake Line
Bubble Flare Fitting
Domestic No-KinkBrake Line
Japanese No-KinkBrake Line
Concave Fitting
Part Tubing Fitting ColorNo. Size Length Size Code
73160 3/8" 8" 5/8-18 Brown73162 3/8" 12" 5/8-18 Brown73166 3/8" 20" 5/8-18 Brown73170 3/8" 30" 5/8-18 Brown73174 3/8" 40" 5/8-18 Brown73178 3/8" 51" 5/8-18 Brown73182 3/8" 60" 5/8-18 Brown
Part Tubing Fitting ColorNo. Size Length Size Code
73110 1/4" 8" 7/16-24 Green73112 1/4" 12" 7/16-24 Green73116 1/4" 20" 7/16-24 Green73119 1/4" 30" 7/16-24 Green73122 1/4" 40" 7/16-24 Green73126 1/4" 51" 7/16-24 Green73127 1/4" 60" 7/16-24 Green
Part Tubing Fitting ColorNo. Size Length Size Code
73083 3/16" 8" 3/8-24 Yellow73085 3/16" 12" 3/8-24 Yellow73089 3/16" 20" 3/8-24 Yellow73092 3/16" 30" 3/8-24 Yellow73095 3/16" 40" 3/8-24 Yellow73099 3/16" 51" 3/8-24 Yellow73100 3/16" 60" 3/8-24 Yellow
Part Tubing Fitting ColorNo. Size Length Size Code
73135 5/16" 8" 1/2-20 Orange73137 5/16" 12" 1/2-20 Orange73141 5/16" 20" 1/2-20 Orange73144 5/16" 30" 1/2-20 Orange73148 5/16" 40" 1/2-20 Orange73152 5/16" 51" 1/2-20 Orange73156 5/16" 60" 1/2-20 Orange
Part TubingNo. Size Length
73200 3/16" 25'73201 1/4" 25'73202 5/16" 25'73203 3/8" 25'
Part TubingNo. Size Length
73250 3/16" 8"73252 3/16" 12"73254 3/16" 20"73256 3/16" 30"73258 3/16" 40"73260 3/16" 51"73262 3/16" 60"
Part TubingNo. Size Length
73251 3/16" 8"73253 3/16" 12"73255 3/16" 20"73257 3/16" 30"73263 3/16" 60"
Part ThreadNo. Size
73275 10 x 1.0mm
X-42 Rev. 3/97
FITTINGS
X-47Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
1/4-283/8" L.
1/4-285/8" L.
1/4-2845° Elbow
1/4 NPT, Metrics and Drive Type Not Illustrated
1/4-28 Reg.
Actual Size Illustrations
1/4-2890° Elbow
Actual Size Illustrations
1/8 NPT45° Elbow
1/8 NPT65° Elbow
1/8 NPT90° Elbow
1/8 NPT2-5/8" L.
1/8 NPTShort
1/8 NPT1-1/4" L.
Grease Fittings
1/8 NPTStraight
Part No.73027
Grease Fitting AdapterPart No. 73055
1/8" Female NPT to1/4-28 Male Machine Threads
Rev. 01/07 X-43a
1/8 NPT1-3/4" L.
Part No. Size Threads Description Length73010 1/4-28 Machine Straight Reg.73013 1/4-28 Machine Straight 3/8" Long73014 1/4-28 Machine Straight 5/8" Long73011 1/4-28 Machine 45° Elbow73012 1/4-28 Machine 90° Elbow73002 5/16-24 Machine Straight Reg.73003 3/8-24 Machine Straight73020 1/8" Pipe Thread Straight 5/8" Long73023 1/8" Pipe Thread Straight 1-1/4" Long73024 1/8" Pipe Thread Straight 1-3/4" Long73025 1/8" Pipe Thread Straight 2-5/8" Long73021 1/8" Pipe Thread 45° Elbow73028 1/8" Pipe Thread 65° Elbow73022 1/8" Pipe Thread 90° Elbow73026 1/8" Pipe Thread Straight Leak Proof73027 1/8" Pipe Thread Female73000 1/4" Pipe Thread Straight Reg.73001 1/4" Pipe Thread 67° Elbow73040 6 mm Metric Mach. Straight Reg.73041 6 mm Metric Mach. 45° Elbow73042 6 mm Metric Mach. 90° Elbow73043 8 mm Metric Mach. Straight Reg.73044 8 mm Metric Mach. 45° Elbow73045 8 mm Metric Mach. 90° Elbow73046 10 mm Metric Mach. Straight Reg.73047 10 mm Metric Mach. 45° Elbow73048 10 mm Metric Mach. 90° Elbow
Drive Type Fittings73029 1/8" O.D. Drive Type Fitting*73030 3/16" O.D. Drive Type Fitting73031 1/4" O.D. Drive Type Fitting73032 5/16" O.D. Drive Type Fitting
*No Ball Check
FITTINGS
X-48 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Grease Fittings
Grease Gun Coupler Grease Gun Hose
Pistol Style Grease GunPart No. 73062
Use only with hand operated grease guns.
Part No. Size73066 12"73067 18"
X-43b Rev. 09/11
Part No. Size73050 Standard73051 4 Jaw 73052 Heavy Duty73053 Lincoln Brand
FITTINGS
X-50 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Black Steel Pipe Fittings
Pipe Nipples (Close) Pipe Nipples
Hex Head Plug Square Hd. Plug Socket Hd. Plug Round Pipe Cap
Rev. 01/13
Size 1/8 1/4 3/8 1/2 3/4 1" 1-1/4 1-1/2 2LengthClose 74001 74021 74041 74061 74081 74101 74121 74143 741551-1/2 74002 74022 74042 74062 74082
2 74003 74023 74043 74063 74083 74102 741222-1/2 74004 74024 74044 74064 74084 74103 74123 74145
3 74005 74025 74045 74065 74085 74104 74124 741583-1/2 74026 74046 74066 74086
4 74008 74027 74047 74067 74087 74106 74126 741605 74029 74049 74069 74089 74108 741286 74011 74031 74051 74071 74091 74110 74130
*Square Drive
X-44
Hex Head Square Head Socket Head Hex Pipe Round PipeSize Plug Plug Plug Cap Cap1/16 743001/8 74260 74280 74301 743201/4 74261 74281 74302 743213/8 74262 74282 74303 743221/2 74263 74283 74304 743233/4 74264 74284 74305 743241" 74287 74306 74325
1-1/4 74288 74307* 743261-1/2 74289 74308* 74327
2 74290 74309* 74328
FITTINGS
X-51Rev. 03/06NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
Black Steel Pipe Fittings
Rev. 8/10
Size Standard Tee 90° Elbow 90° Street Elbow 45° Elbow 45° Street Elbow1/8 74335 74350 74365 74380 743951/4 74336 74351 74366 74381 743963/8 74337 74352 74367 74382 743971/2 74338 74353 74368 74383 743983/4 74339 74354 74369 74384 743991" 74340 74355 74370 74385 74400
1-1/4 74341 74356 74371 74386 744011-1/2 74342 74357 74372 74387 74402
2 74343 74358 74373 74388 74403
Standard 90° 90° Street 45° 45° StreetPipe Tee Elbow Elbow Elbow Elbow
X-45
Schedule 80 Close Nipples
Fully threaded schedule 80 close nipples have thicker walls than the standard nipples do and offer better mechanicalstrength. They are for use with air, water, oil, natural gas & steam. Also known as medium pressure nipples.
Pipe Size Part No.
1/8 741901/4 741913/8 741921/2 741933/4 741941 74195
FITTINGS
X-52 Rev. 06/03 NEBRASKA-IOWA INDUSTRIAL FASTENER CORP. • NATIONAL FASTENER CORP.
742277422974232 74234
7423074233
ExternalSize
Internal Size
1/81/43/81/23/4
74225742267422874231
1/8 1/4 3/8 1/2
Black Steel Pipe Fittings
Reducing Coupling
Pipe Bushing
Pipe Union
Malleable Bushing
Pipe Coupling
A B
Rev. 04/08X-46
Size Coupling Pipe Union1/8 74200 744201/4 74201 744213/8 74203 744221/2 74204 744233/4 74205 744241" 74206 74425
1-1/4 74208 744261-1/2 74209 74427
2 74211 74428
1/8 1/4 3/8 1/2 3/41/4 744403/8 74441 744421/2 74443 74444 744453/4 74446 74447 74448 744491" 74450 74451 74452 74453
A Size
B Size
3/8 1/2 3/4 1 1 1/4 1 1/21" 74240 74241 74242
1-1/4" 74243 74244 742451-1/2" 74246 74247 74248 74249
2" 74250 74251 74252 74253
External Size
Internal Size
top related