front bumper front bumper - toyotadostlari.com · 760hx–02 b58775 radiator grille sub–assy...
Post on 28-Jul-2018
251 Views
Preview:
TRANSCRIPT
760HX–02
B58775
Radiator Grille Sub–assy
Front Bumper Cover
Front Bumper Energy Absorber
Front Bumper Reinforcement
Front Bumper Side Mounting Bracket LH
Front LH Spoiler Sub–assy
Front Fog Light Unit LH
Front Bumper Side Mounting Bracket RH
Front RH Spoiler Sub–assy
Front Fog Light Unit RH
Front Bumper Hole Cover LH
Front Bumper Hole Cover RH
w/ Front Spoiler
w/ Front Spoiler
36 (367, 27)
N⋅m (kgf⋅cm, ft⋅lbf) : Specified torque
36 (367, 27) 5.0 (51, 44 in. ⋅lbf)
w/ Fog Light
w/ Fog Light
Retainerx 4 Retainer
x 4
–EXTERIOR/INTERIOR TRIM FRONT BUMPER76–1
1856Author�: Date�:
2004 COROLLA (RM1037U)
FRONT BUMPERCOMPONENTS
760HY–02
B59104
B59105
Hook
B59112
76–2–EXTERIOR/INTERIOR TRIM FRONT BUMPER
1857Author�: Date�:
2004 COROLLA (RM1037U)
REPLACEMENTHINT:Installation is in the reverse order of the removal. But the installation is indicated only when it has a point.
1. REMOVE RADIATOR GRILLE SUB–ASSY(a) Remove the 2 bolts and clip.(b) Using a screwdriver, remove the radiator grille.HINT:Tape the screwdriver tip before use.
2. REMOVE FRONT BUMPER COVER(a) Remove the 6 screws and 2 clips.(b) Disengage the hook, and remove the front bumper cover.(c) w/ Fog light:
Disconnect the fog light connectors.3. REMOVE FRONT BUMPER ENERGY ABSORBER
4. REMOVE FRONT BUMPER REINFORCEMENT(a) Disconnect the wire harness clamp.(b) Remove the 4 nuts and front bumper reinforcement.
5. REMOVE FRONT BUMPER SIDE MOUNTING BRACKET LH6. REMOVE FRONT BUMPER SIDE MOUNTING BRACKET RH7. REMOVE FRONT LH SPOILER SUB–ASSY (W/ FRONT SPOILER)(a) Remove the screw and 4 retainers.(b) Disengage the clip and front LH spoiler.(c) Employ the same manner described above to the other side.8. REMOVE FRONT RH SPOILER SUB–ASSY (W/ FRONT SPOILER)9. REMOVE FOG LIGHT UNIT LH (W/ FOG LIGHT)(a) Remove the nut and fog light unit.(b) Employ the same manner described above to the other side.10. REMOVE FOG LIGHT UNIT RH (W/ FOG LIGHT)11. REMOVE FRONT BUMPER HOLE COVER LH (W/O FOG LIGHT)12. REMOVE FRONT BUMPER HOLE COVER RH (W/O FOG LIGHT)
B59112
B59244
–EXTERIOR/INTERIOR TRIM FRONT BUMPER76–3
1858Author�: Date�:
2004 COROLLA (RM1037U)
13. INSTALL FRONT BUMPER REINFORCEMENT(a) Install the front bumper reinforcement with the 4 nuts.
Torque: 36 N ⋅m (367 kgf ⋅cm, 27 ft ⋅lbf)
14. INSTALL RADIATOR GRILLE SUB–ASSY(a) Install the radiator grille with the 2 bolts and clip.
Torque: 5.0 N ⋅m (51 kgf ⋅cm, 44 in. ⋅lbf)
760HZ–02
B58776
Spare Wheel Cover Assy
Rear Floor Finish Plate
Luggage Compartment Trim Cover Inner LH
Rear Bumper Side Seal LH
Rear Bumper Cover
Rear Bumper Energy Absorber
Rear Bumper Reinforcement No. 2
Rear No. 1 Spoiler Sub–assy
Bumper Mounting SetBolt No. 1
Rear Bumper Arm LH
Luggage Compartment Trim Cover Inner RH
Rear Bumper Side Seal RH
Rear No. 2 Spoiler Sub–assy
Rear Bumper Reinforcement No. 1
Rear BumperArm RH
N⋅m (kgf⋅cm, ft⋅lbf) : Specified torque
36 (367, 27)
36 (367, 27)
36 (367, 27)
5.5 (56, 49 in. ⋅lbf)
w/ Rear Spoiler
Retainer
Retainer
x 5
x 5
76–4–EXTERIOR/INTERIOR TRIM REAR BUMPER
1859Author�: Date�:
2004 COROLLA (RM1037U)
REAR BUMPERCOMPONENTS
760I7–02
B59106
B59107
B59109
B59108
–EXTERIOR/INTERIOR TRIM REAR BUMPER76–5
1860Author�: Date�:
2004 COROLLA (RM1037U)
REPLACEMENTHINT:Installation is in the reverse order of the removal. But the installation is indicated only when it has a point.1. REMOVE SPARE WHEEL COVER ASSY
2. REMOVE REAR FLOOR FINISH PLATE(a) Remove the 3 clips.(b) Using a moulding remover, remove the rear floor finish
plate.
3. REMOVE LUGGAGE COMPARTMENT TRIM COVERINNER LH
(a) Remove the 4 clips and the luggage compartment trimcover.
(b) Employ the same manner described above to the otherside.
4. REMOVE LUGGAGE COMPARTMENT TRIM COVERINNER RH
5. DISCONNECT REAR BUMPER SIDE SEAL LH(a) Remove the clip and a part of the rear bumper side seal,
as shown in the illustration.HINT:Do not remove the lower side clip.(b) Employ the same manner described above to the other
side.6. DISCONNECT REAR BUMPER SIDE SEAL RH
7. REMOVE REAR BUMPER COVER(a) Remove the 4 nuts.
B59110
Hook
76–6–EXTERIOR/INTERIOR TRIM REAR BUMPER
1861Author�: Date�:
2004 COROLLA (RM1037U)
(b) Remove the 2 screws and 6 clips.(c) Disengage the hook, and remove the rear bumper cover.
8. REMOVE REAR BUMPER ENERGY ABSORBER9. REMOVE REAR BUMPER REINFORCEMENT NO.2(a) Remove the rear bumper reinforcement No. 2 from the rear bumper energy absorber.10. REMOVE REAR NO.2 SPOILER SUB–ASSY (W/ REAR SPOILER)(a) Remove the 5 retainers, screw and the rear spoiler.(b) Employ the same manner described above to the other side.11. REMOVE REAR NO.1 SPOILER SUB–ASSY (W/ REAR SPOILER)12. REMOVE BUMPER MOULDING SET BOLT NO.113. REMOVE REAR BUMPER REINFORCEMENT NO.1(a) Remove the 4 nuts and rear bumper reinforcement No. 1.14. REMOVE REAR BUMPER ARM LH(a) Remove the 3 bolts and rear bumper arm.(b) Employ the same manner described above to the other side.15. REMOVE REAR BUMPER ARM RH16. INSTALL REAR BUMPER ARM LH(a) Install the rear bumper arm with the 3 bolts.
Torque: 36 N ⋅m (367 kgf ⋅cm, 27 ft ⋅lbf)(b) Employ the same manner described above to the other side.17. INSTALL REAR BUMPER ARM RH18. INSTALL REAR BUMPER REINFORCEMENT NO.1(a) Install the rear bumper reinforcement No. 1 with the 4 nuts.
Torque: 36 N ⋅m (367 kgf ⋅cm, 27 ft ⋅lbf)19. INSTALL REAR BUMPER COVER(a) Install the rear bumper cover with the 2 screws, 8 clips and 4 nuts.
Torque: 5.5 N ⋅m (56 kgf ⋅cm, 49 in. ⋅lbf) for nuts
760I1–02
B59776
Protective Tape
Clip
B59775
Clip
Clip
–EXTERIOR/INTERIOR TRIM REAR SPOILER76–7
1862Author�: Date�:
2004 COROLLA (RM1037U)
REAR SPOILERREPLACEMENTHINT:Installation is in the reverse order of the removal. But the installation is indicated only when it has a point.1. REMOVE LUGGAGE COMPARTMENT DOOR COVER
2. REMOVE REAR SPOILER(a) Remove the 2 screws.(b) Disconnect the wire harness connector.(c) Put protective tape.(d) Using a heat light, heat the spoiler to 40 – 60�C (104 –
140�F).(e) Tie both piano wire ends to a wooden block or a similar
object.
(f) Scrape the spoiler protector off by pulling the piano wireas shown in the illustration.
NOTICE:� If reusing the rear spoiler, take care not to damage the
rear spoiler.� Do not damage the body and wire harness.
(g) Remove the 2 clips, wire harness grommet and rear spoil-er.
3. REMOVE CENTER STOP LAMP ASSY(a) Remove the 2 bolts and the center stop lamp assembly.4. INSTALL REAR SPOILER(a) Using a heat light, heat the body mounting surface to 40
– 60�C (104 – 140�F).NOTICE:Do not heat the body excessively.(b) Remove the protective tape from the body.(c) Wipe off the stains with cleaner.(d) Clean the rear spoiler (if reusing the rear spoiler).
(1) Using a heat light, heat the rear spoiler to 40 – 60�C(104 – 140�F).
NOTICE:Do not heat the rear spoiler excessively.
(2) Remove the rear spoiler protector from the rearspoiler.
(3) Wipe off the stains with cleaner.
B59774
Rear Spoiler Side Protector LHRear Spoiler Side Protector RH
Rear Spoiler Protector LHRear Spoiler Protector RH
76–8–EXTERIOR/INTERIOR TRIM REAR SPOILER
1863Author�: Date�:
2004 COROLLA (RM1037U)
(4) Install 4 new rear spoiler protectors to the rear spoil-er as shown in the illustration.
760HU–02
B59289
1
Luggage Compartment Door Name Plate No. 11
2
3 4
Luggage Compartment Door Name Plate No. 22
Luggage Compartment Door Plate No. 43 4
15.4 (0.61)
16.5 (0.65) 83.4 (3.28)
14.8 (0.58)
20.3 (0.80)
13.6 (0.54)
15.8 (0.62)
14 (0.55)
mm (in.)
End of R shape
End of R shape End of R shape
–EXTERIOR/INTERIOR TRIM NAME PLATE76–9
1864Author�: Date�:
2004 COROLLA (RM1037U)
NAME PLATEREPLACEMENT
7610C–02
B57422
ProtectiveTape
B59015
Double–sided Tape
76–10–EXTERIOR/INTERIOR TRIM OUTSIDE MOULDING
1865Author�: Date�:
2004 COROLLA (RM1037U)
OUT SIDE MOULDINGREPLACEMENTHINT:Use the same procedures for the RH side and LH side.
1. REMOVE OUTSIDE MOULDING(a) Put protective tape around the moulding.(b) Insert a piano wire between the vehicle body and mould-
ing.(c) Tie objects that can serve as handles (for example, wood-
en blocks) to all wire ends.(d) Pull the piano wire and scrape off the double–sided tape
that holds the moulding to the vehicle body.NOTICE:� If reusing the moulding, take care not to damage the
moulding.� Becareful not to damage the body.
(e) Remove the moulding.2. INSTALL OUTSIDE MOULDING LH(a) Using a heat light, heat the body.
Heating temperature: 40 to 60 �C (104 to 140�F)NOTICE:Do not heat the body excessively.(b) Remove the double–sided tape from the body.(c) Wipe off the stains with cleaner.(d) Clean the moulding (if reusing).
(1) Using a heat light, heat the body.Heating temperature: 20 to 30 �C (68 to 86�F)
NOTICE:Do not heat the moulding excessively.
(2) Remove the double–sided tape from the moulding.(3) Wipe off the stains with cleaner.(4) Apply new adhesive tape to the moulding as shown
in the illustration.
B59794
26 (1.02)
190 (7.48) 223 (8.78) 233 (9.17) 240 (9.45)
2.6 (0.10)
1.5 (0.059)
mm (in.)
66 (2.60)26 (1.02)
300 (11.81)
–EXTERIOR/INTERIOR TRIM OUTSIDE MOULDING76–11
1866Author�: Date�:
2004 COROLLA (RM1037U)
(e) Using a heat light, heat the body and moulding.Heating temperature:
Item Temperature
Body 40 to 60�C (104 to 140�F)
Moulding 20 to 30�C (68 to 86�F)
NOTICE:Do not heat the body and moulding excessively.(f) Remove the peeling paper from the double–sided tape on
the moulding face.NOTICE:When the peeling paper is removed, take care that no dirtor dust contaminates the adhesive.(g) Affix the moulding to the body, as shown in the illustration.NOTICE:Do not apply excessive force onto the moulding. Usesteady pressure with your thumbs.
760I8–02
B72676
Tape
Moulding Remover
Tape
76–12–EXTERIOR/INTERIOR TRIM FRONT DOOR BELT MOULDING ASSY LH
1867Author�: Date�:
2004 COROLLA (RM1037U)
FRONT DOOR BELT MOULDING ASSY LHREPLACEMENTHINT:� The installation procedures are the removal procedures in reverse order.� Use the same procedures for the RH side and LH side.
1. REMOVE FRONT ARMREST ASSY LH (See page 75–7)2. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSY (W/ POWER WINDOW)
(See page 75–7)3. REMOVE FRONT ARMREST BASE PANEL UPPER LH (W/O POWER WINDOW)
(See page 75–7)4. REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSY (W/O POWER WINDOW)
(See page 75–7)5. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (See page 75–7)6. REMOVE FRONT DOOR TRIM BOARD SUB–ASSY LH (See page 75–7)
7. REMOVE FRONT DOOR BELT MOULDING ASSY LH(a) Put protective tape under the weatherstrip.(b) Using a moulding remover, pry out the weatherstrip as
shown in the illustration.HINT:Tape the moulding remover tip before use.
760I5–02
B72677
Tape
Moulding Remover
Tape
–EXTERIOR/INTERIOR TRIM REAR DOOR BELT MOULDING ASSY LH76–13
1868Author�: Date�:
2004 COROLLA (RM1037U)
REAR DOOR BELT MOULDING ASSY LHREPLACEMENTHINT:� The installation procedures are the removal procedures in reverse order.� Use the same procedures for the RH side and LH side.
1. REMOVE REAR ARMREST ASSY LH (See page 75–20)2. REMOVE POWER WINDOW REGULATOR SWITCH ASSY REAR (W/ POWER WINDOW)
(See page 75–20)3. REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSY (W/O POWER WINDOW)
(See page 75–20)4. REMOVE REAR DOOR TRIM BOARD SUB–ASSY LH (See page 75–20)
5. REMOVE REAR DOOR BELT MOULDING ASSY LH(a) Put protective tape under the weatherstrip.(b) Using a moulding remover, pry out the weatherstrip as
shown in the illustration.HINT:Tape the moulding remover tip before use.
760I0–02
B59781Retainer
Clip
B59781
NewClip
Retainer
76–14–EXTERIOR/INTERIOR TRIM BODY ROCKER PANEL MOULDING LH
1869Author�: Date�:
2004 COROLLA (RM1037U)
BODY ROCKER PANEL MOULDING LHREPLACEMENTHINT:Use the same procedures for the RH side and LH side.
1. REMOVE BODY ROCKER PANEL MOULDING LH(a) Remove the 8 retainers.(b) Using a screwdriver, remove the moulding.HINT:Tape the screwdriver tip before use.(c) Remove the 7 clips from the moulding.
2. INSTALL BODY ROCKER PANEL MOULDING LH(a) Install the moulding with 7 new clips.(b) Install the 8 retainer to the moulding.
760I4–02
B59782
Retainer
Clip
B59782
Retainer
Clip
New Clip
–EXTERIOR/INTERIOR TRIM SIDE MUDGUARD SUB–ASSY LH76–15
1870Author�: Date�:
2004 COROLLA (RM1037U)
SIDE MUDGUARD SUB–ASSY LHREPLACEMENTHINT:Use the same procedures for the RH side and LH side.
1. REMOVE SIDE MUDGUARD SUB–ASSY LH(a) Using a clip remover, remove the 8 retainers and 9 clips.(b) Using a moulding remover, remove the mudguard.
2. INSTALL SIDE MUDGUARD SUB–ASSY LH(a) Install the mudguard with 9 new clips.(b) Install the 8 retainers to the mudguard.
760I3–02
B58077
Clip
76–16 –EXTERIOR/INTERIOR TRIM LUGGAGE COMPARTMENT DOOR GARNISHOUTSIDE
1871Author�: Date�:
2004 COROLLA (RM1037U)
LUGGAGE COMPARTMENT DOOR GARNISH OUTSIDEREPLACEMENTHINT:The installation procedures are the removal procedures in reverse order. However, only installation proce-dures requiring additional information are included.1. REMOVE LUGGAGE COMPARTMENT LOCK CYLINDER & KEY SET(a) Remove the 2 nuts and luggage compartment lock cylinder.
2. REMOVE LUGGAGE COMPARTMENT DOORGARNISH OUTSIDE
(a) Remove the nut.(b) Remove the 4 clips and garnish.
3. INSTALL SYMBOL EMBLEM(a) Using white gasoline, clean the garnish installation surface.(b) Using a heat light, heat the garnish and emblem to 20 to 30�C (68 to 86�F).NOTICE:Do not heat the garnish and emblem excessively.(c) Install the emblem with the 4 clips.
760I2–02
B58072
Clip
Tape
B59795
15 (0.59)
17 (0.67)
Front Side
Rear Side
mm (in.)
–EXTERIOR/INTERIOR TRIM ROOF DRIP SIDE FINISH MOULDING CENTER LH76–17
1872Author�: Date�:
2004 COROLLA (RM1037U)
ROOF DRIP SIDE FINISH MOULDING CENTER LHREPLACEMENTHINT:� Use the same procedures for the RH side and LH side.� The installation procedures are the removal procedures in reverse order. However, only installation
procedures requiring additional information are included.
1. REMOVE ROOF DRIP SIDE FINISH MOULDINGCENTER LH
(a) Apply protective tape onto the circumference of themoulding for protection.
(b) Using a remover for the roof moulding, release the en-gagements of the clips both in the front and rear ends ofthe moulding. Then remove the moulding.
NOTICE:� Do not remove the clips.� If clips are damaged during removal or removed acci-
dentally, replace them.
2. INSTALL ROOF DRIP SIDE FINISH MOULDING CLIPNO.1
NOTICE:Step 2 should be performed only when replacing the clips.(a) Remove the double–sided tape that remains on the
mounting surface of the body, and then clean the surfacewith white gasoline.
(b) Using a heat light, heat the clip installation surfaces of thebody.Heating temperature:
Item Temperature
Body 40 to 60�C (104 to 140�F)
Moulding 20 to 30�C (68 to 86�F)
NOTICE:Do not heat the body and moulding excessively.(c) Set new clips in the positions as shown in the illustration,
and press–fit those clips by hand to install them.HINT:Clips for the roof drip side finish moulding are supply parts.(d) After press–fitting the clips, wait at last 30 minutes. Then
install the moulding.HINT:� Initial hardening time: 30 minutes� Prefect hardening time: 24 hours
760HV–02
B59264
Front Pillar Garnish RH
Front Door Opening Trim RH
Center Pillar Garnish RH
Rear Door Opening Trim RH
Roof Side Garnish Inner RH
Center Pillar Garnish Lower RH
Front DoorScuff Plate RH
Rear Door Scuff Plate RH
Front Pillar Garnish LH
Center Pillar Garnish LH
Rear Door Opening Trim LHRoof Side Garnish Inner LH
Front Door Scuff Plate LH
Center Pillar Garnish Lower LH
Rear Door Scuff Plate LH
Front Door Opening Trim LH
Room Partition Board RH
Package Tray Trim Panel Assy
Sholder AnchorCover Cap
Room Partition Board LH
Room Partition Board LH
Separated Type Rear Seat41.2 (420, 30)
N⋅m (kgf⋅cm ft⋅lbf) : Specified torque
41.2 (420, 30)
Cowl Side Trim Board RH
Cowl Side Trim Board LH
Fixed Type Rear SeatRear Seat Side Cover RH
Rear SeatSide Cover LH
76–18–EXTERIOR/INTERIOR TRIM ROOF HEADLINING ASSY
1873Author�: Date�:
2004 COROLLA (RM1037U)
ROOF HEADLINING ASSYCOMPONENTS
B59298
Roof Headlining Assy
Assist Grip Sub–assy
Assist Grip Sub–assy
RH Visor Assy
LH Visor AssyVisor Holder
Room Lamp Assy No.1
Lens Cover
Assist Grip Sub–assy
w/ Sliding Roof
Map Lamp Assy
Lamp Lens and Cover
Sun Roof Opening Trim Moulding
Assist Grip Sub–assy
–EXTERIOR/INTERIOR TRIM ROOF HEADLINING ASSY76–19
1874Author�: Date�:
2004 COROLLA (RM1037U)
B59265
Roof Headlining Assy
Assist Grip Sub–assy
Assist Grip Sub–assy
RH Visor Assy
LH Visor Assy
Visor Holder
Room lamp Assy No.1
Lens Cover
Assist Grip Sub–assy
w/o Sliding Roof
76–20–EXTERIOR/INTERIOR TRIM ROOF HEADLINING ASSY
1875Author�: Date�:
2004 COROLLA (RM1037U)
760HW–02
B59266
B59267
B59268
Clip
B50588
–EXTERIOR/INTERIOR TRIM ROOF HEADLINING ASSY76–21
1876Author�: Date�:
2004 COROLLA (RM1037U)
REPLACEMENT
1. REMOVE FRONT DOOR SCUFF PLATE RH(a) Using a screwdriver, remove the front door scuff plate RH.HINT:Tape the screwdriver tip before use.2. REMOVE FRONT DOOR SCUFF PLATE LH
3. REMOVE REAR DOOR SCUFF PLATE RH(a) Using a screwdriver, remove the rear door scuff plate RH.HINT:Tape the screwdriver tip before use.(b) Employ the same manner described above to the other
side.4. REMOVE REAR DOOR SCUFF PLATE LH
5. REMOVE COWL SIDE TRIM BOARD RH(a) Remove the clip.(b) Using a screwdriver, remove the cowl side trim board RH.HINT:Tape the screwdriver tip before use.(c) Employ the same manner described above to the other
side.6. REMOVE COWL SIDE TRIM BOARD LH
7. REMOVE FRONT DOOR OPENING TRIM RH8. REMOVE FRONT DOOR OPENING TRIM LH9. REMOVE REAR DOOR OPENING TRIM RH10. REMOVE REAR DOOR OPENING TRIM LH
11. REMOVE CENTER PILLAR GARNISH LOWER RH(a) Pull the center pillar garnish lower RH upward to remove
it.(b) Employ the same manner described above to the other
side.12. REMOVE CENTER PILLAR GARNISH LOWER LH
B55754
B50773
Clip
B59299
Clip
B59277
Clip
Built–in Clip
76–22–EXTERIOR/INTERIOR TRIM ROOF HEADLINING ASSY
1877Author�: Date�:
2004 COROLLA (RM1037U)
13. REMOVE CENTER PILLAR GARNISH RH(a) Using a screwdriver, remove the shoulder anchor cover
cap.HINT:Tape the screwdriver tip before use.(b) Remove the bolt and front seat outer belt shoulder an-
chor.(c) Remove the bolt and front seat outer belt floor anchor.
(d) Using a screwdriver, remove the center pillar upper gar-nish RH.
HINT:Tape the screwdriver tip before use.(e) Employ the same manner described above to the other
side.14. REMOVE CENTER PILLAR GARNISH LH
15. REMOVE REAR SEAT CUSHION ASSEMBLY (See page 72–6, 72–8)16. REMOVE REAR SEAT BACK ASSY (FIXED TYPE REAR SEAT) (See page 72–8)17. REMOVE REAR SEAT BACK ASSY (SEPARATED TYPE REAR SEAT) (See page 72–6)
18. REMOVE REAR SEAT SIDE COVER RH (FIXED TYPEREAR SEAT)
(a) Using a screwdriver, remove the rear seat side cover RH.HINT:Tape the screwdriver tip before use.(b) Employ the same manner described above to the other
side.19. REMOVE REAR SEAT SIDE GARNISH LH (FIXED
TYPE REAR SEAT)
20. REMOVE ROOM PARTITION BOARD LH(SEPARATED TYPE REAR SEAT)
(a) Remove the 2 clips and 2 built–in clips room partitionboard LH.
21. REMOVE ROOM PARTITION BOARD RH(SEPARATED TYPE REAR SEAT)
(a) Remove the clip and 2 built–in clips room partition boardRH.
B59566
Clip
B59276
B59269
Clip
B59270
–EXTERIOR/INTERIOR TRIM ROOF HEADLINING ASSY76–23
1878Author�: Date�:
2004 COROLLA (RM1037U)
22. REMOVE ROOF SIDE GARNISH INNER RH(a) Using a screwdriver, remove the roof side garnish inner
RH.HINT:Tape the screwdriver tip before use.(b) Employ the same manner described above to the other
side.23. REMOVE ROOF SIDE GARNISH INNER LH
24. REMOVE PACKAGE TRAY TRIM PANEL ASSY(a) Using a clip remover, remove the 7 clips.(b) Pull out the belt from the slit and then remove the package
tray trim panel assembly.
25. REMOVE FRONT PILLAR GARNISH RH(a) Using a screwdriver, remove the front pillar garnish RH.HINT:Tape the screwdriver tip before use.(b) Employ the same manner described above to the other
side.26. REMOVE FRONT PILLAR GARNISH LH
27. REMOVE RH VISOR ASSY(a) Remove the 2 screws and RH visor assembly.28. REMOVE LH VISOR ASSY
B59271
B59272
B50594
76–24–EXTERIOR/INTERIOR TRIM ROOF HEADLINING ASSY
1879Author�: Date�:
2004 COROLLA (RM1037U)
29. REMOVE MAP LAMP ASSY (W/ SLIDING ROOF)(a) Remove the screw.(b) Using a screwdriver, remove the map lamp lens and cov-
er.HINT:Tape the screwdriver tip before use.(c) Remove the screw.(d) Using a screwdriver, remove the glove box lamp assem-
bly.HINT:Tape the screwdriver tip before use.
30. REMOVE ROOM LAMP ASSY NO.1(a) Using a screwdriver, remove the lens cover.(b) Using a screwdriver, remove the room lamp assembly
No.1 as shown in the illustration.
31. REMOVE ASSIST GRIP SUB–ASSY(a) Using a screwdriver, remove the 2 assist grip covers.(b) Remove the 2 screws and assist grip sub–assy.
B50596
90�
B59278
B59273 B59931
Clip
w/ Sliding Roof
w/o Sliding Roof
–EXTERIOR/INTERIOR TRIM ROOF HEADLINING ASSY76–25
1880Author�: Date�:
2004 COROLLA (RM1037U)
32. REMOVE VISOR HOLDER(a) Remove the holder of the sun visor by turning it counter-
clockwise.
33. REMOVE SUN ROOF OPENING TRIM MOULDING (W/ SLIDING ROOF)
34. REMOVE ROOF HEADLINING ASSY(a) Remove the 3 clips and roof headlining assembly.
B59275
B59274 B59930
Tape
w/ Sliding Roof
w/o Sliding Roof
Tape
76–26–EXTERIOR/INTERIOR TRIM ROOF HEADLINING ASSY
1881Author�: Date�:
2004 COROLLA (RM1037U)
35. INSTALL ROOF HEADLINING ASSY(a) Align the markings, and then install the wire harness with
tape.HINT:Be careful for dirt or foreign objects not to stick to the adheredpart when peeling off the double–stick tape.(b) Attach the roof wire harness across the adhered part.NOTICE:Roof wire harness should be attached securely.(c) Install the 3 clips.
36. INSTALL ROOM PARTITION BOARD RH (SEPARATED TYPE REAR SEAT)37. INSTALL ROOM PARTITION BOARD LH (SEPARATED TYPE REAR SEAT)38. INSTALL REAR SEAT SIDE COVER RH (FIXED TYPE REAR SEAT)39. INSTALL REAR SEAT SIDE GARNISH LH (FIXED TYPE REAR SEAT)40. INSTALL REAR SEAT BACK ASSY (FIXED TYPE REAR SEAT) (See page 72–8)41. INSTALL REAR SEAT BACK ASSY (SEPARATED TYPE REAR SEAT) (See page 72–6)
top related