gewerbering 9, d-83624 otterfing, germany, 08024-48737 ... · pdf filegewerbering 9, d-83624...
Post on 06-Mar-2018
228 Views
Preview:
TRANSCRIPT
KMT - Kraus Messtechnik GmbH Gewerbering 9, D-83624 Otterfing, Germany, 08024-48737, Fax. 08024-5532 Home Page http://www.kmt-telemetry.com, Email: info@kmt-telemetry.com
MTP
Multi channel telemetry system for rotating
application, full software programmable
with 16 bit resolution
2 to 64 channel 16 bit ADC, simultaneous sampling
Signal bandwidth 0-24000Hz Full software programmable
Inputs for STG, TH-K, ICP or VOLT Inductive or battery power
STG - Auto Zero calibration Rugged housing, water protected
4V bridge Excitation Output analog +/- 10V
Gain 125-250-500-1000-2000 Digital data interface to PC
Version 2016-03 2 Technical Data are subject to change without notice!
Short description:
The MTP telemetry is a small and flexible telemetry system for rotating applications. Each sensor module (2-channel) is equipped with signal conditioning, anti-aliasing filters, analog-to-digital converters and a digital output. All these up to 32 modules (=64 channels) will controlled by MTP-Controller module. By this concept it’s possible to install the acquisition modules close to the sensor to have short connect ions for the
analog sensor lines. This avoids an undesired coupling of disturbances resulting in noisy signals. The interference insensitive digital outputs then can lead over wider distances of up to 25cm module to module. The MTP-Controller output is a PCM bit stream signal which can be modulated for emission by a transmitter module for distances of up to 0.1 with inductive telemetry transmission or up to 10m with radio telemetry
transmission. Suitable for wireless data transmission rates of 312.5kbit/s up to 5000kbit/s
MTP acquisition modules (rotor side)
80 x 34 x 14 mm
Weight 60 grams
MTP-STG-V3 Acquisition module for 2 strain gages
Full, half and quarter bridge (≥350) Fixed excitation 4V DC Offset calibration by auto zero Manual offset shifting after auto zero Gain: 125-250-500-1000-2000 Test shunt-cal step Signal bandwidth 0Hz to 24000Hz* (*see table of cut-off-frequency)
Resolution 16bit Accuracy <0.2% Powering: 6.5-9V DC Current consumption with full bridge 350 ohm 75mA Vibration: 5g Static acceleration: 3000g Shock: 10000g
80 x 34 x 14 mm
Weight 60 grams
MTP-VOLT-V3 Acquisition module for 2x high level inputs Range: ±0,625V, ± 1,25V, ±2,5V, ± 5V, ±10V Signal bandwidth 0Hz to 24000Hz* (*see table of cut-off-frequency)
+4V sensor excitation max. 20mA Resolution 16bit Accuracy <0.2% Powering: 6.5-9V DC Current consumption 60mA Vibration: 5g Static acceleration: 3000g Shock: 10000g
80 x 34 x 14 mm
Weight 60 grams
MTP-ICP®
Acquisition module for 2 ICP sensors Current EXC. 4mA Gain: 1-2-4-8-16-32 Signal bandwidth 3 Hz to 24000Hz* (*see table of cut-off-frequency)
Resolution 16bit Accuracy <0.2% Powering: 6.5-9V DC
Current consumption 100mA Vibration: 5g Static acceleration: 3000g Shock: 10000g
80 x 34 x 14 mm
Weight 60 grams
MTP-TH-K Acquisition module for 2x TH-K Inputs galvanic isolated Range -50 to 1000°C, -50 to 500°C or -50 to 250°C Cut-off filter 30Hz (more on request) Resolution 16bit Accuracy: 0.2% at 1000°C range Powering: 6.5-9V DC
Current consumption 110mA Vibration: 5g Static acceleration: 3000g Shock: 10000g
MTP-Pt100/1000 (RTD)
Acq. module for 2 RTD sensors Range -100 to 600°C, -50 to 300°C or -25 to 150°C Type Pt100 or Pt1000 Current EXC. 1mA Connection: 4-, 3- and 2 wire Sensor break detection Signal bandwidth 6Hz Resolution 16bit Accuracy <0.2% Powering: 6.5-9V DC Current consumption 60mA Vibration: 5g Static acceleration: 3000g Shock: 10000g
80 x 34 x 14 mm Weight 60 grams
MTP-CONTROL
Controller 1- 32 acquisition modules Output: PCM Programmable via LAN adapter Powering: 6.5-9V DC Current consumption 40mA, with LAN-setup adapter 140mA Vibration: 5g Static acceleration: 3000g Shock: 10000g
Additional environmental
Operating Temperature -20 – +80°C Storage Temperature -30 – +90°C Humidity 100%
Signal bandwidth, sampling rates and delay time:
Cut off frequency from anti-aliasing filter (-3dB) and sampling rate (red)
Delay Time from Analog In to Analog Out (theoretical, brown)
Bit rate 2 Channels 4 Channels 8 Channels 16 Channels 32 Channels 64 Channels
5000 kbit/s ------
24000 Hz max. (62500 Hz)
1,6 ms
12000 Hz (31250 Hz)
2,3 ms
6000 Hz (15625 Hz)
4,5 ms
3000 Hz (7812.5 Hz)
8,9 ms
1500 Hz (3906.25 Hz)
17,9 ms
2500 kbit/s 24000 Hz max.
(62500 Hz)
1,6 ms
12000 Hz (31250 Hz)
2,3 ms
6000 Hz (15625 Hz)
4,5 ms
3000 Hz (7812.5 Hz)
8,9 ms
1500 Hz (3906.25 Hz)
17,9 ms
750 Hz (1953.125 Hz)
35,7 ms
1250 kbit/s 12000 Hz
(31250 Hz) 2,3 ms
6000 Hz (15625Hz)
4,7 ms
3000 Hz (7812.5 Hz)
9,1 ms
1500 Hz (3906.25 Hz)
17,9 ms
750 Hz (1953.125 Hz)
35,7 ms
375 Hz (976.56 Hz)
71,5 ms
625 kbit/s 6000 Hz
(15625Hz) 4,7 ms
3000 Hz (7812.5 Hz)
9,4 ms
1500 Hz (3906.25 Hz)
18,3 ms
750 Hz (1953.125 Hz)
35,7 ms
375 Hz (976.56 Hz)
71,5 ms
190Hz (488.28 Hz) 142,3 ms
312,5 kbit/s 3000 Hz
(7812.5 Hz)
9,4 ms
1500 Hz (3906.25 Hz)
19,1 ms
750 Hz (1953.125 Hz)
36,3 ms
375 Hz (976.56 Hz)
71,5 ms
190 Hz (488.28 Hz)
142,5ms
95 Hz (244.14 Hz)
285 ms
Version 2016-03 3 Technical Data are subject to change without notice!
MTP-DEC8/16/32 Receiver unit for max 32 Channels output via 37 pol. Sub D (inductive transmission 45MHz version up to 5000Mbit)
Plug-side
Optional BNC16/32 Box. Connect on 37pol Sub-D
MTP –DEC8/16/24/32 System Parameters:
Channel: 8,16 or 32x +/-10V analog outputs via Sub-D male socket
Resolution: 16 bit D/A converter, with smoothing filter
Power supply input: 10-30 VDC, power consumption <24 Watt
Transmission: Digital PCM Bi-Phase Format – FSK, receiver
Dimensions: 205 x 105 x 65mm
Weight: 1.25 kg without cables and antenna
Overall system accuracy between encoder input and decoder output: <0.2% without sensor influences
Environmental
Operating: -20 … +70°C
Humidity: 20 ... 80% not condensing
Vibration: 5g
Static acceleration: 10g in all directions
Shock: 100g in all directions
Front side view Rear side view
Power Switch
7-pole female TUCHEL connector for power supply input (10–30V DC)
IND-Pickup head connection
Fuse of powering defect LED
Out of function
Active level LED of Pickup head
Female 37 pole Sub-D for analog signal output, CH 1 to 32
Power ON LED
IND-Pickup head connection (at
diversity option)
Active level LED of Pickup head
Transmission error LED
Version 2016-03 4 Technical Data are subject to change without notice!
MTP-DEC8/16/32 Receiver unit for max 32 Channels output via 37 pol. Sub D (radio transmission version with diversity receiver 320-1280kbit)
Plug-side
Optional BNC16/32 Box. Connect on 37pol Sub-D
MTP –DEC8/16/24/32 System Parameters:
Channel: 8,16 or 32x +/-10V analog outputs via Sub-D male socket
Resolution: 16 bit D/A converter, with smoothing filter
Power supply input: 10-30 VDC, power consumption <24 Watt
Transmission: Digital PCM Bi-Phase Format – FSK,
Dimensions: 205 x 105 x 65mm
Weight: 1.25 kg without cables and antenna
Overall system accuracy between encoder input and decoder output: <0.2% without sensor influences
Environmental
Operating: -20 … +70°C
Humidity: 20 ... 80% not condensing
Vibration: 5g
Static acceleration: 10g in all directions
Shock: 100g in all directions
Front side view Rear side view
HF –Field strength display Transmission error LED
Fuse of powering defect LED
Power Switch
PCM out for IP-LAN-Interface (Opt.) (Option)
Female 37 pole Sub-D for analog
signal output, CH 1 to 32
7-pole female TUCHEL connector for power supply input (10–30V DC)
SMA antenna connector with
active LED of antenna (diversity)
Out of function!
top related