installation and operation manual hunter ceiling fans
Post on 07-Jul-2018
220 Views
Preview:
TRANSCRIPT
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
1/35
41457 -01 7/2000
®
Installation and Operation Manual
For Hunter Ceiling Fans
41457 -01 7 /2000
®
SINCE 1886
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
2/35
2
41457 -01 7/2000
®
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
3/35
41457 -01 7/2000
®
CONGRATULATIONS!Your new H unter ceiling fan is anaddition to your hom e or office that
w ill provide com fort and perfor-m ance for m any years. This m anualgives you com plete instructions forinstalling and operating your fan.
W e are proud of our w ork. W e ap-preciate the opportunity to supplyyou w ith the best ceiling fan avail-able anyw here in the w orld.
Before installing your fan, record thefollow ing inform ation for yourrecords and w arranty assistance.Please refer to the carton and theH unter nam eplate (located on topoutside fan m otor housing) for theproper inform ation.
© 2000 Hunter Fan Co.
7 /2000
M odel N am e __________________
C atalog N o. ___________________
Serial N o. _____________________
D ate Purchased ________________
W here Purchased ______________
_____________________________
Please attach your H ardw are Sheetand Exploded View Sheet to this
m anual for future reference.
Atta ch You r Receiptor a Copy of
You r Receipt Here
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
4/35
4
41457 -01 7/2000
®
CONTENTSIm portant Inform ation .......................................................................................................................................5
Step 1 - G etting Ready ......................................................................................................................................6Step 2 - Installing the C eiling Plate ....................................................................................................................8
Step 3 - Assem bling Pipe/Ball A ssem bly...........................................................................................................10
Step 4 - Assem bling the Fan ............................................................................................................................12
Step 5 - H anging the Fan ................................................................................................................................14
Step 6 - Installing the Rem ote .........................................................................................................................15
Step 7 - W iring the Fan ...................................................................................................................................18
Step 8 - A ttaching the C anopy........................................................................................................................20
Step 9 - A ssem bling Fan Blades.......................................................................................................................21
Step 10 - A ttaching the Sw itch H ousing ..........................................................................................................23
Step 11 - Installing Light Fixture ......................................................................................................................26
O perating Your H unter Fan and Rem ote .........................................................................................................30
C leaning and M aintenance .............................................................................................................................32
Troubleshooting ..............................................................................................................................................33
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
5/35
41457 -01 7/2000
®
IMPORTANT INFORMATIONnot lock the circuit break-ers in the off position, se-
curely fasten a prominentwarning device, such as atag, to the service panel.
• All wiring must be in accor-dance with national and lo-cal electrical codes andANSI/NFPA 70. If you areunfamiliar with wiring, youshould use a qualified elec-
trician.• To reduce the risk of per-
sonal injury, do not bendthe blade attachment sys-tem when installing, bal-ancing, or cleaning the fan.Never insert foreign objectsbetween rotating fanblades.
DO YOU NEED HELP?
To install a ceiling fan, be sure youcan do the follow ing:
• Locate ceiling joist or other suit-able support in ceiling.
• D rill holes for and install w oodscrew s.
• Identify and connect electricalw ires.
• Lift 40 pounds.
If you need help installing the fan,
your H unter fan dealer can direct youto a licensed installer or electrician.
• To reduce the risk of fire,electrical shock, or motor
damage, do not use a solid-state speed control withthis fan. Use only Hunterspeed controls.
WARNINGS
• To avoid possible electricalshock, before installingyour fan, disconnect thepower by turning off thecircuit breakers to the out-let box and associated wall
switch location. If you can-
CAUTIONS
• Read entire booklet care-fully before beginning in-stallation and save theseinstructions.
• To reduce the risk of per-sonal injury, attach the fandirectly to the supportstructure of the building ac-cording to these instruc-tions, and use only the
hardware supplied.
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
6/35
6
41457 -01 7/2000
®
GATHERING THE TOOLS
You w ill need the follow ing tools for
installing the fan:• Electric drill w ith 9/64" bit
• Standard screw driver
• Phillips-head screw driver
• W rench or pliers
OPTIONAL ACCESSORIES
C onsider using H unter’s optional ac-
cessories, including a w all-m ounted
or rem ote speed control. To install and
use the accessories, follow the instruc-
tions included w ith each product.
For quiet and optim um perform ance
of your H unter fan, use only H unter
speed controls.
STEP 1 - GETTING READY PREPARING THE FAN SITE
The location of a ceiling fan and how
the fan is attached to the buildingstructure are essential for reliableoperation, m axim um efficiency, andenergy savings. For this reason, w ehave included a separate booklet —“G uide to C hoosing and Preparinga C eiling Fan Site”— to help youselect the best location for your fan.The booklet also provides inform a-
tion to ensure your fan support andelectric outlet box m eet U L-approvedsafety codes for ceiling fans.
The instructions in this installationm anual assum e that you have used“G uide to C hoosing and Preparinga C eiling Fan Site”to pick the fanlocation and m ake certain the proper
fan support and outlet box are in-stalled.
CHECKING YOUR FAN PARTS
C arefully unpack your fan to avoid
dam age to the fan parts. C heck forany shipping dam age to the m otoror fan blades. If one of the fan bladesw as dam aged in shipm ent, return allthe blades for replacem ent.
Hint: If you are installing m ore thanone fan, keep the fan bladesin sets, as they w ere shipped.
The fan includes a separate diagramof the screw s and other sm all partsneeded for the fan. Keep this dia-gram handy for identifying parts dur-ing installation; the diagram indicatesthe step in w hich each part is used.
If any parts are m issing or dam aged,contact your H unter dealer or callH un ter Parts D epartm ent at
901-248-2222.
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
7/35
41457 -01 7/2000
®
INSTALLER’S CHOICE®
This patented 3-position m ountingsystem provides you m axim um instal-lation flexibility and ease. You can
install your H unter fan in one of threew ays. The steps in this m anual in-clude specific instructions for the fanm ounting m ethod of your choice. Fora ceiling 8 feet or higher, standardm ounting is recom m ended.
Flush Mounting (Figure 1a) fitsclose to the ceiling, for low ceilingsless than 8 feet high.
Standard Mounting (Figure 1b)
hangs from the ceiling by a connec-tor pipe (included), for ceilings 8 feetor higher. For ceilings higher thaneight feet, you can purchase H unterextension rods. A ll H unter fans usesturdy 3/4" diam eter pipe to assurestab ility and w obble-free perfor-m ance.
Angle Mounting (Figure 1c) hangsfrom a vaulted or angled ceiling.
Figure 1c - Angle MountingFigure 1b - Standard MountingFigure 1a - Flush Mounting
10"12"
34° Max
Pitch
12
8
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
8/35
8
41457 -01 7/2000
®
STEP 2 - INSTALLING THE CEILING PLATE4. A lign the slotted holes in the ceil-
ing plate w ith the pilot holes in
the w ood supp ort structure.Note: The isolation pads shouldbe flush against the ceiling.
1. D rill tw o pilot holes into the w oodsupport structure through the
outerm ost holes on the outletbox. The pilot holes should be9/64" in diam eter by 2 3/4" indepth.
2. Bring the lead w ires around thesides of the ceiling plate. Thread-ing the lead w ires through thehole in the m iddle m ay causeproblem s w hen installing the re-
m ote and trying to close thecanopy.
3. Your fan com es w ith tw o neo-prene noise isolators. Position theisolators betw een the ceiling plateand ceiling by inserting the raisedareas on each isolator into theholes in the ceiling plate. Refer toFigure 2a.
Figure 2a - Adding Isolators to Ceiling
Plate
Figure 2b - Correct Position of Ceiling
Plate for Angle Mounting
Ceiling Plat eHooks
Isolators
Ceiling
Pla te
For Angle Mounting Only: Besure to orient the ceiling plate so
that the tw o hooks point up to-w ards the ceiling peak as show nin Figure 2b.Note: You w ill usethe hooks to support the fanw hile w iring the fan.
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
9/35
41457 -01 7/2000
®
Figure 2c - Attaching Ceiling Plate to2 x 4 Brace
2 x 4 Brace
Ceiling Joist
Ceiling
Out le t Box
CeilingPla te
Fla tWasher
3" WoodScrew
5. Place a flat w asher on each of thetw o 3 " screw s and pass thescrew s through the slotted holesin the ceiling plate as show n in
Figure 2c.6. Tighten the screw s into the 9/64"
pilot holes; do not use lubricantson the screw s. D o no t over-tighten.
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
10/35
10
41457 -01 7/2000
®
continued
A s discussed in STEP 1 - G ETTIN GREA D Y, your H unter fan can be in-
stalled in a standard m ounting posi-tion.
Included w ith the fan are tw o pipes:one 3" long pipe/ball assem bly forstandard m ounting on 8' ceilings andone 12" long pipe for 9' ceilings andhigher. See Figure 3a.
If you are going to install the fan us-ing the standard m ounting, go toSTEP 4 - A SSEM BLIN G THE FA N .
If you are going to install the fan us-ing the 12" long pipe for 9' ceilingsor higher, com plete the steps below .
STEP 3 - ASSEMBLING PIPE/BALL ASSEMBLY 3. Rem ove the ball from the pipe.
4. Rem ove the pin from the pipe.
Figure 3a - Pipes
Figure 3b - Removing ball assem-bly
REMOVING BALL ASSEMBLY
For the follow ing steps refer toFigures 3b and 3c.
1. Locate the 3" pipe/ball assem bly.
2. Rem ove the positioning screwfrom the top of the ball.
NOTE: The ball w ill becom eloose and should slide dow n the
pipe.
3" Pipe /Ba llAssembly
12" Pipe
Pin
Posit ioning Screw
Lea dw ireAssembly
BallGroundScrew
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
11/35
41457 -01 7/2000
®
8. Insert the pin into the tw o holesin the 12" pipe so that the pin isplaced evenly in the hole.
9. Insert the threaded end of the
pipe into the flat side of the ball.
10.A lign the cutouts in the ball w iththe pin and the ground screw as-sem bly.
11.Slide the ball up the pipe until ithits the pin.
12.Insert and tighten the positioningscrew into the ball so that the
head of the screw is tight on theend of the pipe.
NOTE: M ake sure that the ballis positioned so that it is level orstraight.
CAUTION
Do not overtighten the posi-tioning screw as it may causethe ball to seat improperly, re-sulting in fan wobble and thefan hanging crookedly.
WARNING
• Failure to complete thesteps above properly couldresult in the fan falling.
Figure 3c - 12" pipe assembly
CAUTION
Make sure that the leadwireassembly is pointing straightup and away from the pipe.
WARNING
• To avoid possible electrical
shock, the ground screwmust be tightened securely.
5. C arefully loosen and rem ove theground screw /leadw ire assem blyfrom the pipe.
6. Locate the 12" pipe.
7. Insert and tighten the groundscrew /leadw ire assem bly into thesm all screw hole on one end ofthe 12" pipe.
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
12/35
12
41457 -01 7/2000
®
STEP 4 - ASSEMBLING THE FANU se the Step 4 instructions for thetype of m ounting you have selected:
standard, angle, or flush.STANDARD AND ANGLEMOUNTING
For Standard 8-foot Ceilings andHigher
1. Insert the p ipe through thecanopy as show n in Figure 4a.
Feed w ires from the fan throughthe canopy then throu gh the
pipe.2. Screw pipe into fan assem bly un-
til tight. IM PORTANT! Tightenpipe setscrew as show n in Figure4a.
CAUTION
The pipe has a special coatingon the threads. Do not remove
this coating; the coating pre-vents the pipe from unscrew-ing. Once assembled, do notremove the pipe.
FLUSH MOUNTING
For Low Ceilings
1. Tighten or rem ove pipe setscrew .Fit the canopy over the hangerFigure 4a - Inserting Pipe through
Canopy
Pipe
Canopy
Pipe
Setscrew
Figure 4b - Placing Canopy andWasher Over Adapter
Assembly
Washer
Canopy
Adapter
Top o f Fan
adapter as show n in Figure 4b.M ake sure the canopy fits snugly
against the fan assem bly w ith nospace betw een the pieces.
2. You w ill find a large assem blyw asher included w ith the fan.Place the w asher over the adapterand canopy as show n in Figure4b.
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
13/35
41457 -01 7/2000
®
Figure 4d - Attaching Canopy to Fan
Assembly
AssemblyWasher
Adapter ThreadedHole
Figure 4c - Positioning Assembly
Washer Slots over Threaded Holes
3. Position the slots in the assem -bly w asher over the threadedholes in the adapter as show nin Figure 4c.
4. A ttach the canopy tightly to thefan assem bly w ith three #8-32assem bly screw s and lockw ashersas show n in Figure 4d.
Assembly Screw an d Lockw asher
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
14/35
14
41457 -01 7/2000
®
STEP 5 - HANGING THE FAN
Figure 5b - Assembled Fan Hangingfrom Ceiling Plate Hooks
CeilingPla te
Figure 5a - Attaching Slots on Canopyto Ceiling Plate Hooks
1. D isconnect the pow er by turningoff the circuit breakers to the out-let box and associated w all sw itchlocation.
2. Tilt and hang the assem bled fanfrom the ceiling plate hooks. Sliptw o rectangular canopy slots overceiling plate hooks as show n inFigures 5a and 5b.
Note: To hang the fan you m usttilt the canopy to an alm ost verti-cal position so the canopy slotscom e dow n over the ceiling platehooks.
If you are installing the remotecontinue to STEP 6, INSTALLING
THE REMOTE, otherwise skip toSTEP 7, WIRING THE FAN, on page18.
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
15/35
41457 -01 7/2000
®
STEP 6 - INSTALLING THE REMOTERem ote M odel #: UC 7067RC
Ratings: 120 VA C , 60 H z, 1.0 A m p Fan
250 W atts incandescent light
• To avoid possible electricalshock, before installing theremote, be sure that allpower is disconnected byturning off the circuitbreakers to the outlet box.
• All wiring must be per-formed in accordance withnational and local electricalcodes. If you are unfamil-iar with the wiring codes,you should use a qualifiedelectrician.
• To avoid overheating andpossible damage to other
equipment, do not installto control a receptacle,
WARNINGS
Note: This device com pliesw ith Part 15 of the FC CRules. O peration is subjectto the follow ing tw o condi-
tions: (1) this device m ay notcause harm ful interference,and (2) this device m ust ac-cep t an y interference re-ceived, including interfer-ence that m ay cause undes-ired operation.
SETTING UP THE TRANSMITTER
1. Rem ove the battery cover from
the transm itter by pressing dow non the arrow and sliding the coveroff. Refer to Figure 6a.
continued
fluorescent light fixture,motor operated appliance,
or transformer-suppliedappliance. Use only to con-trol one paddle-blade ceil-ing fan and incandescentlight fixture.
Figure 6a - Setting the Code on theTransmitter
Dip Sw itches
9 Volt Ba t te ry
Ba t tery Cover
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
16/35
16
41457 -01 7/2000
®
2. Slide the dip sw itches to the de-sired on/off position using a ball-point pen or sm all-head screw -driver. Rem em ber the on/off po-sition of the sw itches for usew hen setting up the receiver.
Note: Be sure to change the fac-tory default sw itch settings toyour ow n unique code.
3. Install a 9 volt battery (not in-cluded). Refer to Figure 6a onpage 15.
Note: To prevent dam age to thetransm itter, rem ove the batteryif it is not used for long periodsof tim e.
4. Replace the battery cover on thetransm itter.
5. M ount the rem ote holder usingthe tw o screw s provided w ith the
rem ote kit. Slide out center pieceon the holder to see screw holes.
Replace center piece after m ount-ing to w all. Refer to Figure 6b.
6. The transm itter can be placed onthe rem ote holder for conve-
nience or safe-keeping.
INSTALLING THE RECEIVER
1. Slide the dip sw itches to the sam eon/off position as the transm itterusing a ball-point pen or sm all-
head screw driver. Refer to Figure6c.
Figure 6b - Mounting the RemoteHolder
Figure 6c - Setting the Code on theReceiver
ON
1 2 3 4
ON
Dip Sw itche s
Screw Hole
Screw Hole
Screw HoleCover
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
17/35
41457 -01 7/2000
®
2. M ake w iring connections usingthe w ire nuts supplied. To con-nect the w ires, place bare m etalleads together. Place a w ire nutover the intertw ined length ofw ire and tw ist clockw ise untiltight as show n. Refer to Figure6d.
Figure 6e - Positioning the Receiver
Inside of the Canopy
3. Place receiver inside the canopyunder the ceiling plate. Refer toFigure 6e. Be sure to keep theantenna positioned securely ontop of the receiver. Do not m odifyor dam age the antenna w ire, ascontrol perform ance m ay be re-duced.
Connect ..............................................................................................................ToG reen w ire from fan ....................................................................Bare ground w ireBlack w ire from receiver ..............................................................Black supply w ireW hite w ire from receiver............................................................W hite supply w ireW hite w ire from receiver.........................................................W hite w ire from fanBlack w ire from receiver ...........................................................Black w ire from fanBlack/W hite w ire from receiver.................................... Black/W hite w ire from light
Once receiver is installed and
power is turned back on, DONOT pull the fan or light chainswhile power is connected.
WARNING
CeilingPla te
Antenna
Receiver
Canopy
Figure 6d - Wiring the Receiver
Black/
White
Black Black
White White
White
Black
Black/
White
AC
Pow er
In
Antenna
Note: For optim al perform ance,the antenna should extend out-side the canopy.
4. C ontinue to STEP 8, H A N G IN G
THE FA N , on page 20.
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
18/35
18
41457 -01 7/2000
®
CAUTION
Be sure no bare wire or wire
strands are visible after mak-ing connections.
STEP 7 - WIRING THE FAN1. You can use either one or tw o
w all sw itches to control the fanand/or lights separately. U se con-nection 1 on page 19 to
• control the light w ith a w allsw itch and the fan w ith achain pull (one w all sw itch re-quired)
• control the light w ith a chainpull and the fan w ith a w allsw itch (one w all sw itch re-
quired)• control the light w ith one w all
sw itch and the fan w ith an-other (tw o w all sw itches re-quired)
U se connection 2 on page 19 ifthere is no separate w all sw itchpow er w ire for the light fixture.
Note: W all sw itches not included.
continued
2. C onnect the w ires as show n inFigure 7a. To connect the w ires,place the bare m etal leads to-gether. Place a w ire nut over theintertw ined length of w ire andtw ist clockw ise u ntil tight asshow n.
3. Separate the connected w ires byplacing the green and w hite w ireson one side of the outlet box andthe black and the black/w hite
w ires on the other side of theoutlet box.
4. Turn the connectors upw ard. Pushthe w ires gently into the outletbox.
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
19/35
41457 -01 7/2000
®
Bare or Green
Green
ApprovedConnectors
Power
WiresInCeiling
White
W h i t e
B l a c k
Black/White
1
2 Connections:
Black
Wall Switch Wire ForSeparate Control of Light Fixture
CeilingPlate
Outlet Box
2 x 4 Brace
Green GroundWire from HangerPipe (not presentwith flush mountingoption)
3 WiresFrom Fan
(Note: Wall switchmust be acceptableas a general-useswitch.)
Connect Blk/Wht Wire from fanto Wall Switch Wire for separatecontrol of light fixture, orConnect Blk/Wht Wire from fanto Ceiling Black Wire if thereis no separate Wall Switch Wirefor the light fixture.
1
2
Figure 7a - Wiring The Fan
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
20/35
20
41457 -01 7/2000
®
STEP 8 - ATTACHING THE CANOPY
Figure 8a - Attaching Canopy toCeiling Plate
Figure 8b - Canopy Tabs and Grooves
in Hanger Ball
Sub-steps 1 and 2 apply to Flush,Standard, and A ngle m ounting. Sub-step 3 applies to Standard and A nglem ounting only.
1. Sw ing the fan up so as to alignthe canopy screw holes w ith them ounting holes on the ceilingplate. Refer to Figure 8a.
2. Install and tighten the tw o #10-32 x 1/2" m ounting screw s.
3. For Standard and AngleMounting Only: In addition tosub-steps 1 and 2, lift the fanhousing tow ards the ceiling androtate the fan until each canopytab engages a groove in thehanger ball as show n in Figure 8b.
Note: If the tabs are already en-gaged, do not rotate.
WARNING
Failure to complete sub-steps1 through 3 could cause fan tofall. (Sub-step 3 not applicablefor flush mounting.)
Ceiling
Pla te
Canopy
Groove inH a ng e rBall
CanopyTa b
Groove inHanger Ba l l
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
21/35
41457 -01 7/2000
®
Figure 9a - Inserting Grommet intoFan Blade
Figure 9b - Attaching Fan Blade toBlade Iron
Figure 9c - Attaching Fan Blade toBlade Iron using Decorative Medallion
feature a decorative m edallion asw ell as a blade iron. Insert theassem bly screw s into the bladeiron, through the blade and intothe m edallion, w ith the bladesandw iched betw een the bladeiron and m edallion as show n inFigure 9c.
H unter fans use several styles of fanblade irons (brackets that hold theblade to the fan).
1. Your fan m ay include blade grom -m ets (see Parts List). If your fanhas grom m ets, insert them byhand into the holes as show n inFigure 9a.
2. A ttach each blade to blade ironusing three blade assem bly screw sas show n in Figure 9b. Som e fans
STEP 9 - ASSEMBLING FAN BLADESIf you used grom m ets, the bladesm ay appear slightly loose afterscrew s are tightened. This is nor-m al.
3. Rem ove the blade m oun tingscrew s an d rubber shippingbum pers from the m otor.
Grommet
Fan
Blade
Medallion
Blade
Iron
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
22/35
22
41457 -01 7/2000
®
4. For each blade, insert one bladem ou nting screw throu gh theblade iron as show n in Figure 9d,
and attach lightly to the fan. In-sert the second blade m ountingscrew , then securely tighten bothm ounting screw s.
Figure 9d - Attaching Blade Irons to
Hub of Fan Assembly
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
23/35
41457 -01 7/2000
®
STEP 10 - ATTACHING THE SWITCH HOUSING
Figure 10a - Attaching Upper Switch
Housing to Switch Housing MountingPlate
HousingAssembly
Screw
Sw itchHousingMount ing
Pla te Upper PlugConnector
UpperSw itchHousing
Figure 10b - Mounting the Upper
Switch Housing
CAUTION
Make sure the upper switch
housing is securely attached tothe switch housing mountingplate. Failure to properly at-tach and tighten all three hous-ing assembly screws could re-sult in the switch housing andlight fixture falling.
The sw itch housing is m ade up oftw o sections: the upper sw itch hous-ing, and the low er sw itch housing.
ATTACHING THE UPPER SWITCHHOUSING
1. Partially install tw o #6-32 x 3/8"housing assem bly screw s into thesw itch housing m ounting plate asshow n in Figure 10a.
2. Feed the upper plug connectorthrough the center opening of theupper sw itch housing. See Figure
10a.
3. A lign the keyhole slots in the up-per sw itch housing w ith the hous-ing assem bly screw s installed insub-step 1.
4. Turn the upper sw itch housingcounterclockw ise until the hous-ing assem bly screw s are firm ly
situated in the narrow end of thekeyhole slots as show n in Figure10b. Install the one rem aining #6-32 x 3/8" housing assem bly screwinto the third hole in the uppersw itch housing. Tighten all threescrew s firm ly.
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
24/35
24
41457 -01 7/2000
®
Table 10-1
Fan w ith no lightfixture included
Fan w ith acces-
sory light kit in-cluded
Fan w ith m ulti-light light fixtureincluded
Figure 10c - Lower Switch HousingWithout Light Kit or Single-GlobeLight Fixture
Figure 10d - Lower Switch Housing
With Multi-Light Fixture
continued
ATTACHING THE LOWERSWITCH HOUSING
Your hunter fan includes one of tw olow er sw itch housings. Both low er
sw itch housings are show n in Figures10c and 10d. The type of low ersw itch housing you have depends onw hether your fan includes a light fix-ture, and if so, w hat type of light fix-ture it is. U se table 10-1 to assist you.
If your fan has a low er sw itch hous-ing as show n in Figure 10c, and youA RE installing an accessory light kit
or single-globe light fixture includedw ith your fan , go directly to STEP11 - IN STA LLIN G LIG H T FIX TU RE.
See Figure 10c
See Figure 10c
See Figure 10d
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
25/35
41457 -01 7/2000
®
If your fan has a low er sw itch hous-ing as show n in Figure 10c and youA RE N O T installing a light fixture, orif your fan has a low er sw itch hous-ing as show n in Figure 10d, com -
plete the follow ing steps:
1. C onnect the upper plug connec-tor from the m otor to the low erplug connector in the low ersw itch housing assem bly. See Fig-ure 10e.
Note: Both plug connectors arepolarized and w ill only fit together
one w ay. M ake sure that bothconnectors are properly alignedbefore connecting them together.Incorrect connection could causeim proper operation and dam ageto the product.
Figure 10e - Plug Connection andLower Switch Housing Installation
UpperSw itch
HousingUpper Plug
Connector
Low er Plug
Connector
Lo w er
Sw itchHousingHousing
Assembly
Screw
2. Place the low er sw itch housingassem bly over the upper sw itchhousing. A lign the side screwholes in the upp er and low ersw itch housings. Attach the low er
sw itch h ou sing to the up persw itch housing w ith three #6-32x 3/8" housing assem bly screw s.See Figure 10e.
Note: If your fan does not includea light fixture, you m ay purchasean accessory light kit separately.See STEP 11 - IN STALLIN G LIG H T
FIXTU RE.
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
26/35
26
41457 -01 7/2000
®
STEP 11 - INSTALLING LIGHT FIXTUREYour fan m ay include a light fixture.Inform ation for w iring and installingall included H unter light fixtures fol-
low s.
Note: If you purchased a fan w ith-out a light fixture, you m ay purchasean accessory light kit separately. Forbest perform ance and beauty, useonly H unter-brand light kits, Type A -Z. H unter light kits are designed,tested, and U L approved for all
H unter fans, and are available atm ost H unter dealers. To install thelight kit, follow the instructions in-cluded w ith the kit.
If you are not installing a light fix-ture, turn to O PERA TIN G Y O U RH U N TER FA N for additional instruc-tions.
WARNING
• To avoid possible electrical
shock, before installinglight fixtures, disconnectpower by turning off thecircuit breakers both to theoutlet box and to its asso-ciated wall switch location.If you cannot lock the cir-cuit breakers in the off po-sition, securely fasten aprominent warning device,
such as a tag, to the servicepanel.
• Connect house wiring tothe fan before attachingthe light fixture to the fan.
• All wiring must be in accor-dance with national and lo-cal electrical codes andANSI/NFPA 70. If you are
unfamiliar with wiring, youshould use a qualified elec-trician.
INSTALLING INCLUDED ACCES-SORY LIGHT KIT
1. Rem ove the p lug and sw itchho using caps from the low ersw itch housing. Refer to Figure11a.
Note: D o not discard the caps.You w ill need this if you rem ovethe light fixture in the future.
2. Locate the w hite w ire and theblack w ire com ing from the lightfixture.
3. Thread the tw o w ires from thelight fixture through the centerhole in the low er sw itch housing.Be sure to thread the black w irew ith the larger connector headthrough first and then thread thew hite w ire w ith the sm aller con-
nector head through.
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
27/35
41457 -01 7/2000
®
continued
the w ires. M aking sure the lightfixture m ounting screw holes arealigned; hold the light fixture andtighten the nut on the inside ofthe low er sw itch housing. Insert
and tighten the tw o #6-32 sem slight fixture m ounting screw s.
5. Refer to Figure 11b. Locate theblack/w hite w ire and the w hitew ire in the fan sw itch housingthat have connectors attached.Pull the dum m y term inals out ofboth connectors. C onnect the
black/w hite w ire to the black w ireof the light kit. C onnect the w hite
Figure 11a - Removing Plug Buttonand Switch Housing Cap
Low e rSw it ch
Housing
Plug But to n
Sw itchHousingCa p
4. Screw the fixture into the low ersw itch housing. Th read the
lockw asher and nut provided over
w ire to the w hite w ire of the lightkit.
6. C onnect the upper plug connec-tor from the m otor to the low erplug co nnector in the low ersw itch housing assem bly. See Fig-ure 10e on page 25.
CAUTION
Be sure no bare wire or wirestrands are visible after mak-ing connections.
Dum my Termina ls( to be remo ved w hen
hoo king up l ight ki t)
Wires Fro mThe Fan
Wires Fro mThe Ligh t Kit
Figure 11b - Wiring Connections for Light Kit
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
28/35
28
41457 -01 7/2000
®
INSTALLING INCLUDED ACCES-SORY LIGHT FIXTURE GLOBESAND BULBS
1. Place globe over thread edlam pholder in cup. Install andhand tighten threaded lockingring on lam pholder as show n inFigures 11c and 11d.
2. Install bulbs. U se 120V, 60Wm axim um m edium base incan-descent bulbs. Turn pow er O N atm ain panel.
Figure 11c - Installing the Globes
Cu p
Threa de dLam p Holder
Threa de dLocking RingGlobe
Figure 11d - Assembling the Locking
Ring
Beginning o fFirst Thre a d
Threa de dLocking Ring
Notch in Ring
Note: A s show n in Figure 11d,line up the beginning of the firstthread on the lam pholder andnotch on the locking ring toavoid cross threading the ring.
If the ring becom es hard to turn,rotate the ring counter clockw iseto loosen and reposition. Do notforce the ring on.
Note: Both plug connectors arepolarized and w ill only fit togetherone w ay. M ake sure that bothconnectors are properly alignedbefore connecting them together.
Incorrect connection could causeim proper operation and dam ageto the product.
7. Place the low er sw itch housingassem bly over the upper sw itchhousing. A lign the side screwholes in the upper and low ersw itch housings. A ttach the low er
sw itch h ousing to the u pp ersw itch housing w ith three #6-32x 3/8" housing assem bly screw s.See Figure 10e on page 25.
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
29/35
41457 -01 7/2000
®
INSTALLING ACCESSORY LIGHTKITS
To install the light kit, follow the in-structions included w ith the kit for
w iring, m ounting, and assem bly. A f-ter com pleting the light kit installa-tion, follow sub-steps 1 and 2 onpage 23 to reattach the low er sw itchhousing.
Figure 11f - Multi-Light Fixture
Cu p
G lob e
SilencerBand
Thu mb -screw
G lob e
Thu mb screw
Bulb
Figure 11e - Single-Globe Fixture
INSTALLING SINGLE-GLOBEFIXTURE BULB AND GLOBE
Refer to Figure 11e.
1. Install light bulbs.
2. Insert the globe around the bulband into the fixture. Install andtighten thum bscrew s m anually.D o not overtighten.
INSTALLING INTEGRATED MULTI-LIGHT FIXTURE BULBS ANDGLOBES
Refer to Figure 11f.
1. Place silencer band around theneck of each globe.
2. Insert globe in cup.
3. Install and tighten thum bscrew sm anually. D o not overtighten.
4. Install bulbs.
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
30/35
30
41457 -01 7/2000
®
•The chain uses a breakaw ayconnector that separates if thechain is jerked. If this happens,
sim ply reinsert the chain intothe connector.
3. C eiling fans w ork best by blow -ing air dow nw ard (counterclock-w ise blad e rotation) in w armw eather to cool the room w ith a
OPERATING YOUR HUNTER FAN AND REMOTEYour H unter Fan com es w ith anacessory pull chain pendant for bothfan and light operation. To install the
pull chain pendants, insert the looseend of the pull chain pendant intothe breakaw ay connector on the fanand light pull chains.
OPERATING YOUR HUNTER FANWITHOUT REMOTE
1. Turn on electrical pow er to thefan.
2. The pull chain controls pow er tothe fan. The chain has four set-tings in sequence: H igh, M edium ,Low and O ff.
•Pull the chain slow ly to changesettings.
•Release slow ly to prevent thechain from recoiling into the
blades.
Figure 12a - Air Flow Patterns
direct breeze. In w inter, havingthe fan draw air upw ard (clock-w ise blade rotation) w ill distrib-ute the w arm er air trapped at the
ceiling around the room w ithout
PullChain
ReversingSwitch
Figure 12b - Pull Chain and Reversing
Switch
causing a draft. Refer to Figure12a.
To change the direction of air
flow , turn the fan off and let itcom e to a com plete stop. Slidethe reversing sw itch on the fanto the opposite position as show nin Figure 12b. Restart fan.
4. If your fan w obbles w hen oper-ating, use the enclosed balancingkit and instructions to balance the
fan.
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
31/35
41457 -01 7/2000
®
OPERATING YOUR HUNTER FANWITH A REMOTE
Once receiver is installed and
power is turned back on, DONOT pull the fan or light chainswhile power is connected.
WARNING
Refer to steps 1, 3, and 4 in the O P-ERATIN G YO U R HU N TER FA NW ITHO U T A REM O TE. U se thefollow ing steps to operate yourrem ote.
1. Turn O N the w all sw itch. The lightw ill turn O N at m axim um bright-ness.
2. Light Operation:
Press and quickly release the lightbutton on the hand held rem oteto turn the light O FF or O N .
Press and hold the light button for
m ore than 0.7 second to dim or
LOW MED HIGH
Display
Light But ton
Fan But ton
brighten the light. Release thelight button w hen the desiredlight level is reached. The lightdim m er range is 20% to 100% .The Light key has auto resum e,
so the brightness w ill stay thesam e as the last tim e it w as turnedO FF. Refer to Figure 12c.
3. Fan Operation:
Press the fan button to turn O Nthe ceiling fan at H igh speed.Press again to change the speedto M edium , then again to Low ,
and then again to turn the fanO FF. Refer to Figure 12c.
Note: If fan is not reaching de-sired speed or light does notcom e on, refer to the TRO U BLE-SHO O TIN G section. Figure 12c - Remote Transmitter
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
32/35
32
41457 -01 7/2000
®
CLEANING AND MAINTENANCEC aring for blades: W ood finishblades should be cleaned w ith a fur-niture polishing cloth. O ccasionally,
a light coat of furniture polish m aybe applied for added protection andbeauty. Painted and high-glossblades m ay be cleaned in the sam em anner as the fan finish.
MANUFACTURER'SPHONE NUMBERIf you need parts or service
asssitance, please call 901-248-2222or visit us at our W EB site at:
http://w w w .hunterfan.com
C aring for finishes: For cleaning, asoft brush or lint-free cloth shouldbe used to prevent scratching the fin-
ish. A vaccuum cleaner brush nozzlecan rem ove heavier dust. Surfacesm udges or an accum ulation of dirtand dust can easily be rem oved byusing a m ild detergent and a slightlydam pened cloth. A n artistic agentm ay be used, but never use abrasivecleaning agents as they w ill dam agethe finish.
®
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
33/35
41457 -01 7/2000
®
TROUBLESHOOTING
N othing happens; fan does not m ove.
W ithout Rem ote (refer to page 35 for
troubleshooting W ith Rem ote).
N oisy operation.
1. Pow er turned off, fuse blow n, or
circuit breaker tripped.
2. Loose w ire connections or w rong
connections.
3. M otor reversing sw itch not en-gaged.
4. Pull chain sw itch not “on.”
5. Shipping bum pers still in place.
1. Blade brackets screw ed loosely to
m otor.
2. Blade screw ed loosely to blade iron.
3. Blade cracked.
PROBLEM PROBABLE CAUSE SOLUTION1. Turn pow er on, replace fuse, or re-
set breaker.
2a.Loosen canopy, check all connections
according to STEP 7 - W IRIN G TH E
FAN (turn power off before
checking).
2b.C heck the plug connection in the
sw itch housing according to STEP
10 - ATTA C H IN G THE SW ITCH
HO USING .
3. Push sw itch firm ly up or dow n.
4. Pull sw itch chain.
5. Rem ove shipping bum pers.
1. Tighten screw s until snug.
2. Tighten screw s until snug.
3. Replace all blades.continued
®
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
34/35
34
41457 -01 7/2000
®
PROBLEM PROBABLE CAUSE SOLUTIONN oisy operation (continued).
Excessive w obbling.
Note: W hen sw itching from m edium
to low speed, you m ay notice som e fan
w obble. W hen the fan stabilizes at lowspeed, w obble w ill disappear.
4. U sing non-approved speed control.
5. G lass screw ed loosely to fixture.
6. Sw itch housing is loose.
1. U nbalanced blades.
2. Loose blades or blade irons.
3. Fan not secure on hanger assem -
bly.
4. Fan hanger ball not seated in
canopy tabs.
4. C hange to approved speed control.
5. H an d-tighten the light fixture
screw s. Ensure that rubber noise
isolators are installed.
6. C heck and tighten screw s to the
sw itch housing m ounting plate and
to the upper and low er sw itch
housing.
1. U se balancing kit included w ith fan.
2. Tighten all screw s.
3. Turn pow er off, support fan very
carefully, loosen canopy and hang
correctly.
4. Turn pow er off, support the fan
very carefully, and check that the
hanger ball is properly seated.
If you have tried these troubleshooting solutions and still have trouble, call 901-248-2222 or visit our
W eb site at http://w w w .hunterfan.com .continued
®
-
8/18/2019 Installation and Operation Manual Hunter Ceiling Fans
35/35
41457 -01 7/2000
®
PROBLEM PROBABLE CAUSE SOLUTION
N o functions operate or do not operatecorrectly. (W ith Rem ote)
1. M ain Pow er not restored.
2. Fan pull chain not set to H igh.
3. Light pull chain not set to O N .
4. Receiver w iring incorrect.
5. Transm itter and receiver dipsw itches do not m atch.
6. Battery too w eak.
1. Replace fuse. Turn O N circuitbreaker. Turn O N w all sw itch.
2. Turn O FF pow er at w all sw itchor m ain electric panel. Set fanto H igh speed.
3. Set light kit to O N .
4. Verify w iring connections.
5. Set transm itter and receiver tosam e dip sw itch setting.
6. Replace w ith new battery.
O perates only at close range. (W ith Re-
m ote)
1. Signal blocked from reaching
receiver.2. Battery too w eak.
1. Extend antenna into ceiling box,
or m ove it for better reception.2. Replace w ith new battery.
Inconsistent operation. (W ith Rem ote) 1. Signal partially blocked fromreaching receiver.
2. RF interference.
3. C ontinuing RF interference.
1. Extend antenna into ceiling box,or m ove it for better reception.
2. Turn O FF w all sw itch for 5seconds, then turn back O N .
3. C hange dip sw itch settings to adifferent code in both Transm it-ter and Receiver.
top related