model code - bsi group australasian bottled water institute...australasian bottled water institute...
Post on 13-Mar-2020
3 Views
Preview:
TRANSCRIPT
Model Code
Revised June 2013
Australasian Bottled Water Institute
A Division of the
Australian Beverages Council
Level 1, 6-8 Crewe Place
Rosebery, NSW, 2018,
Phone: +61 2 96622844
Email: info@australianbeverages.org
www.australianbeverages.org
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 2.
Contents
Section I - Objectives ................................................................................................................. 6
Section II – Scope, Use and Definitions ...................................................................................... 8
2.1 Scope ............................................................................................................................... 8
2.2 Use ................................................................................................................................... 9
2.3 Definitions & Acronyms................................................................................................... 10
Section III – Primary Production ............................................................................................... 15
3.1 Environmental Hygiene of Source ................................................................................... 15
3.2 Hygienic Production of Food Sources .............................................................................. 17
3.2.1 Source Water ............................................................................................................ 17
3.2.2 Finished Product ....................................................................................................... 17
3.3 Handling, Storage and Transport .................................................................................... 17
3.4 Cleaning, Maintenance & Personnel Hygiene at Primary Production .............................. 17
Section IV – Establishment: Design and Facilities ..................................................................... 19
4.1 Location .......................................................................................................................... 19
4.2 Premises and Rooms ....................................................................................................... 19
4.3 Equipment .......................................................................................................................20
4.4 Facilities ..........................................................................................................................20
Section V – Control of Operation ..............................................................................................22
5.1 Control of Food Hazards ..................................................................................................22
5.2 Key Aspects of Hygiene Control Systems ........................................................................ 23
5.2.1 Treatment of Product Water .................................................................................... 23
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 3.
5.2.2 Containers ................................................................................................................ 23
5.2.3 Cleaning and Sanitising Solutions ............................................................................ 24
5.3 Incoming Material Requirements ................................................................................... 24
5.3.1 Air Under Pressure ................................................................................................... 24
5.3.2 Bulk Water ................................................................................................................ 25
5.4 Packaging ....................................................................................................................... 25
5.5 Source and Operations Water ........................................................................................ 26
5.6 Management and Supervision......................................................................................... 27
5.7 Documentation and Records ........................................................................................... 27
5.8 Recall Procedures ............................................................................................................ 27
Section VI – Establishment: Maintenance and Sanitation ........................................................ 29
6.1 Maintenance and Cleaning ............................................................................................. 29
6.2 Cleaning Programs .......................................................................................................... 30
6.3 Pest Control Systems ...................................................................................................... 32
6.4 Waste Management ........................................................................................................ 32
6.5 Monitoring Effectiveness ................................................................................................ 32
Section VII – Establishment: Personal Hygiene ......................................................................... 34
7.1 Health Status ................................................................................................................... 34
7.2 Illness and Injuries ........................................................................................................... 34
7.3 Personal Cleanliness ........................................................................................................ 34
7.4 Personal Behaviour ......................................................................................................... 34
7.5 Visitors ............................................................................................................................ 34
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 4.
Section VIII – Transportation .................................................................................................... 35
8.1 General ............................................................................................................................ 35
8.2 Requirements .................................................................................................................. 35
8.3 Use and Maintenance ...................................................................................................... 39
Section IX – Product Information and Consumer Awareness ................................................... 40
9.1 Lot Identification ............................................................................................................ 40
9.2 Product Information ....................................................................................................... 40
9.3 Labelling ........................................................................................................................ 40
9.4 Consumer Information .................................................................................................... 41
Section X – Training ................................................................................................................. 42
10.1 Awareness and Responsibilities .................................................................................... 42
10.2 Training Programs ........................................................................................................ 42
10.3 Instruction and Supervision .......................................................................................... 42
10.4 Refresher Training ........................................................................................................ 42
Section XI - Standard of Analytical Compliance ....................................................................... 44
11.1 Testing Summary ......................................................................................................... 44
11.2 Hydrogeology of Source ................................................................................................ 45
11.3 Microbiology .................................................................................................................. 47
11.3.1 Source Water Microbiological Limits ....................................................................... 47
11.3.2 Bottled Water Microbiological Limits..................................................................... 49
11.4 Chemistry ..................................................................................................................... 49
11.4.1 Physical Properties of Bottled and Source Water ................................................... 49
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 5.
11.4.2 Radionuclide Testing of Source Water .................................................................... 50
11.4.3 Inorganic Compounds in Source or Bottled Water .................................................. 50
11.4.4 Organic Compounds in Bottled or Source Water .................................................... 52
11.4.5 Volatile Organic Compounds in Bottled or Source Water ....................................... 53
11.4.6 Additional Volatile Organic Compound Screening in Source or Bottled Water ....... 53
Section XII – Model Code Checklist ........................................................................................... 56
12.1 Introduction ................................................................................................................... 56
12.2 Definitions and Acronyms ............................................................................................. 56
12.3 Product Quality ............................................................................................................. 57
12.4 Good Manufacturing Practices ...................................................................................... 58
12.5 Plant Construction and Design ..................................................................................... 64
12.6 Plant Hygiene ................................................................................................................ 67
12.7 Plant Design ................................................................................................................. 69
12.8 Cooler Cleaning ............................................................................................................. 76
12.9 Record Keeping ............................................................................................................. 76
12.10 Laboratory Maintenance ............................................................................................. 77
12.11 Labeling Requirements ................................................................................................ 77
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 6.
Section I - Objectives
The ABWI Model Code has been developed as a Standard of Excellence for the production of
bottled waters for the protection of consumers, bottlers and other participants of the industry.
The Model Code has been adopted by the bottler members of ABWI. Bottler members must
participate in the Plant Inspection Program to maintain their membership of the ABWI and
they must be audited annually by a third party, independent auditor operating in compliance
with Guidelines for quality and/or environmental systems auditing, ISO 19011.
The Model Code is based on quality systems combined with Good Manufacturing Practices
(GMP). The Model Code requires that members have a third party audited HACCP (hazard
analysis, critical control point) system in place and it is a requirement that this document is
used in combination with the Recommended International Code of Practice – General
Principles of Food Hygiene, (CAC/RCP 1-1969, Rev. 3(1997)), of Codex text as amended. This
code should also be used in combination with the Principles for the Establishment of and
Application of Microbiological Criteria for Foods (CAC/GL 21-1997).
The water that is sourced and used for bottled waters may come from a variety of sources.
Typically many waters are sourced from an underground aquifer to produce a still or sparkling,
spring or mineral water. Bottlers may also bottle treated water obtained from a municipal
water authority. However there is a range of other types of waters available. Provided such
waters are selected, collected, transported, filled and sealed in a safe and sanitary manner, and
are treated to ensure that they remain in the same quality as when first bottled; for the length
of their shelf-life; consumers can enjoy all waters with confidence.
Bottled waters may be produced and labeled as follows:-
a) bottled water with ‘added fluoride’
b) drinking water,
c) glacier water,
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 7.
d) mineral water,
e) mineralised water,
f) packaged water,
g) purified water,
h) rain water,
i) spring water,
j) table water,
k) or other appropriately designated water, consistent with the Australia New Zealand
Food Standards Code and/or ACCC or NZ TPA or any other applicable national
regulations.
The ABWI Secretariat will send all members a reminder 3 months prior to their anniversary or
nominated date. A follow -up reminder will be sent if ABWI has not been advised of the date
booked for the audit within 30 days of the original reminder being sent.
Bottlers are required to have had their audit conducted and passed prior to their anniversary
date each year and to advise the ABWI office of their passing score, each year.
The ABWI Secretariat will provide Certified Bottlers with a copy of the contract that is to be
signed by the bottler, to enable them to use the ABWI Certified Bottler logo.
This Model Code for Bottled Water has been prepared by the Australasian Bottled Water
Institute, its membership, Board of Directors and Committees.
For questions about the Model Code contact: Australasian Bottled Water Institute, Level 1, 6 -
8 Crewe Place, Rosebery NSW 2018, or info@bottledwater.org.au
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 8.
Section II – Scope, Use and Definitions
2.1 Scope
The intent of the ABWI Model Code and the accompanying Plant Inspection Program is to
assist bottler and source owner members in their endeavors to produce a quality product,
providing information and direction with technical procedures and quality systems and
standards. As a result, the requirements of the Model Code exceed those of mandatory food
law as set out in the Australia New Zealand Food Standards Code.
Regardless of where the water may be sourced, fully documented procedures with all check
results recorded and in conjunction with quality systems are required to be maintained.
The ABWI Model Code requires members to undertake a rigorous and onerous testing regime.
This includes scheduled daily, weekly and annual testing. ABWI considers this test regime to be
essential.
The Australasian Bottled Water Institute's Plant Inspection Program has been developed to
assist members to achieve a standard whereby they will be considered ‘bottlers of excellence’.
This program is supported by the use of a registered logo that is only available for use by
Certified Bottlers.
It is a REQUIREMENT that where applicable, ABWI members do NOT operate a bottled water
plant or bottle water for the purpose of sale or distribution without passing the ABWI Plant
Inspection Program within 12 months of joining ABWI.
If you are a bottler supplying to a supermarket, you may be required to conform to the
following retail audit standards (detailed below) where additional requirements to that of the
ABWI requirements will need to be fulfilled;
1) Woolworths Quality Assurance (WQA)
2) Safe Quality Food (SQF )
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 9.
3) British Retail Consortium (BRC)
4) Coles Quality Assurance
2.2 Use
a) Bottler members are required to comply with the Plant Inspection Program based on the
requirements of the ABWI Model Code.
b) Bottlers must submit to document review and annual audit as required by ABWI.
c) Surveillance and certification audits may only be conducted by ABWI approved registered
auditors.
d) The scope of the audit is the ABWI Model Code.
e) Bottlers are expected to have completed and passed the audit prior to the anniversary date
of their initial audit.
f) The Model Code is designed around a series of compliance points that a bottler "MUST"
comply with, supported by processes and procedures that are “REQUIRED” or
“recommended”.
g) To attain a pass, bottlers need to comply with all "MUST" and “REQUIRED” points for the
supporting requirements that a bottler is “REQUIRED” or "recommended” to comply with.
h) Where a bottler does NOT comply with all " MUST" or “REQUIRED”, they have 30 days to
complete corrective actions and have these approved by the auditor or as arranged. Where the
non-compliance relates to the annual water testing for organic and volatiles then the bottler
will be allowed a maximum of 60 days to have the test results returned.
i) Bottlers may apply to ABWI for a concession of a given period of time, where it is not possible
for the non-compliance to be closed within the time period stated above. This concession will
be given at the discretion of the Executive Director. In this case a document review may be
requested.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 10.
j) Where a bottler does not achieve a score of 70% or higher, but has complied with all "MUST"
requirements, they have 60 days to attend to the necessary points, identified by the auditor,
and to have their plant or documentation re-evaluated to achieve full conformance with the
code.
k) ABWI accredited auditors are required to provide the bottler with a copy of the completed
audit checklist, along with any corrective action reports (CARs) that are issued on the day of
audit, or as agreed with the auditee. The 30 / 60 days permitted to fulfill these noncompliance
will commence from that day.
l) Observers or technical advisors may be present on the day of certification audits. Others that
may be present include translators which would be recorded as such on any audit report.
m) If any conflict is noted by auditor or auditee an exemption may be sought from ABWI for
circumstances such as where there may be problems of communication for the bottler, e.g.:
English is their second language, where consultants could act as a translator for example.
n) Bottlers will obtain and maintain "Certified Bottlers" status passing their annual audit.
o) The use of the ABWI logo is only permitted by Certified Bottlers. For the requirements
dealing with the use of the logo please see the ABWI contract for the use of the logo.
p) Source owners may seek separate Source Certification. In this event they MUST meet the
compliance points for an approved source for chemical and microbiological testing (See
Standard of Analytical Compliance). Certified sources MUST also carry out the annual testing
regime.
q) The ABWI Executive Director has the discretion to extend the period of certification upon
request by the bottler
2.3 Definitions & Acronyms
ABWI Members are REQUIRED to comply with the definitions described below:-
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 11.
Adequate - is that which accomplishes the intended purpose in keeping with good health
practices.
Approved method - a methodology approved by the National Accreditation Testing
Association (NATA) or certified (accredited) by a third-party organisation acceptable to ABWI.
Approved Source - a source for which approval has been obtained and maintained in
accordance with chemical and microbiological testing requirements (See Standard of
Analytical Compliance). The bottler MUST maintain in the plant a current license or certificate
of approval of the source where issued (by state or department).
Bottled Water - water that is intended for human consumption and that is sealed in bottles or
other containers with no added ingredients except that it may optionally contain safe and
suitable antimicrobial agents. Firms may manufacture non-standardised bottled water
products with ingredients such as minerals for flavour. The common or usual name of the
resultant product will reflect these additions.
Bulk Water - water intended for potable use which is transported via tanker truck or
equivalent means from one area to another for the purpose of treatment, packaging and
human consumption.
Closure – Container lid
Demineralised water - bottled water which is produced by distillation, deionisation, reverse
osmosis, or other suitable process.
Drinking water - water that is intended for human consumption and that is sealed in bottles or
other containers with no added ingredients except that it may optionally contain safe and
suitable antimicrobial agents. Firms may manufacture non-standardised drinking water
products with ingredients such as minerals for flavour. The common or usual name of the
resultant product will reflect these additions.
Food-contact surfaces - are those surfaces that contact human food and those surfaces from
which drainage onto the food or onto surfaces that contact the food ordinarily occurs during
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 12.
the normal course of operations. "Food-contact surfaces" include utensils and food-contact
surface of equipment.
Fluoridated bottled water – Any still, bottled water, to which fluoride has been added, in
accordance with the provisions set out in the FSANZ Food Standards Code.
Ground water - water from a subsurface saturated zone that is under a pressure equal to or
greater than atmospheric pressure. Ground water MUST not be under the direct influence of
surface water.
Lot - a collection of primary containers or unit packages of the same size, type and style
produced under conditions as nearly uniform as possible and designated by a common
container code, batch code or marking.
Microorganisms - yeast, molds, bacteria and viruses and includes, but is not limited to, species
having public health significance. The term "undesirable microorganisms" includes those
microorganisms that are of public health significance, that subject food to decomposition, that
indicate that food is contaminated with filth, or that otherwise may cause food to be
adulterated. Occasionally in these regulations, the adjective "microbial" is used instead of an
adjectival phrase containing the word microorganism.
Mineral Water - ground water obtained from a subterranean water-bearing strata that, in its
natural state, contains soluble matter. It is a REQUIREMENT that mineral water have a level
of total dissolved solids of greater than 250 ppm. No minerals may be added to such water.
Multi-service containers - containers intended for use more than one time
MUST - is used to state mandatory requirements.
Natural Water - bottled spring, mineral or well water which is derived from an underground
formation or water from surface water that only requires minimal processing, is not derived
from a municipal system or public water supply, and is unmodified except for limited
treatment (e.g., filtration, ozonation or other proven disinfection processes).
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 13.
Nontoxic materials - materials for product water contact surfaces utilised in the transporting,
processing storing and packaging of bottled water, which are free of substances which may
render the water injurious to health or which may adversely affect the flavour, colour, odour, or
bacteriological quality of the water.
Operations water - water that is delivered under pressure to a plant for container washing,
hand washing, plant and equipment, cleanup and for other sanitary purposes.
Pest - refers to any objectionable animals or insects including, but not limited to, birds,
rodents, flies and larvae.
Plant Operator - any person who owns or operates a bottled water plant. A certified plant
operator is one who has met the requirements of the ABWI Certified Plant Operator Course,
and has passed refresher examination every three years hence.
Potable Water – water that meets the Australian Drinking Water Guidelines, such as municipal
water.
Primary container - the immediate container in which the product water is packaged.
Product water - operations water that has been fully processed ready for final product
formulation.
Purified Water - bottled water produced by distillation, deionisation, reverse osmosis.
Sanitize - to adequately treat food-contact surfaces by a process that is effective in destroying
vegetative cells of microorganisms of public health significance, and in substantially reducing
numbers of other undesirable microorganisms, but without adversely affecting the product or
its safety for the consumer.
Recommended - is used to state recommended or advisory procedures to identify conditions
that should be met. A minimum of 90% compliance against the audit checklist is required.
REQUIRED / REQUIREMENT/MUST - is used to state a process or procedure which requires
full compliance of ABWI bottlers.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 14.
Shipping case or shipper - means a container in which one or more primary containers of the
product are held
Single-service container - means a container intended for one time usage only.
Source - when used in reference to a bottled water plant's product water, means the original
source of the water, prior to any transportation, processing or treatment.
Spring water - means ground water obtained from subterranean a water-bearing stratum
that, in its natural state, contains soluble matter. No minerals may be added to such water.
Unit package - means a standard commercial package of bottled water, which may consist of
one or more containers.
Water dealer - means any person who imports bottled water or causes bulk water to be
transported for bottling for human consumption or other consumer uses.
Well water - means water from a hole bored, drilled, or otherwise constructed in the ground
which taps the water of an aquifer.
ABWI Australasian Bottled Water Institute
ADWG Australian Drinking Water Guidelines
CCP Critical Control Point
CP Control Point
FSANZ Food Standards Australia New Zealand
GMP Good Manufacturing Processes
HACCP Hazard Analysis and Critical Control Point
NHMRC National Health and Medical Research Council
WHO World Health Organisation
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 15.
Section III – Primary Production
3.1 Environmental Hygiene of Source
1. Approval of the source water product derived from a source other than a public water supply
MUST be based upon a field inspection of the source and a review of information prepared by
a professionally qualified hydrogeologist
2. Report by the professionally qualified hydrogeologist MUST demonstrate the integrity of
the source and safety of the catchment operations, and that MUST include:
a) An evaluation of the chemical, physical, microbiological, and radiological
characteristics of the source.
b) A report on the regional geology surrounding the site and the specific site geology. A
description of the vertical and horizontal extent of the source aquifer using existing
data. The information will be used to define the recharge area of the aquifer, or in the
case of regional aquifers, the zone of influence of the subject source.
c) A report detailing the development of the source; the method of construction
including spring design, well installation, surface catchment, and intake structures; and
transmission facilities as appropriate.
d) A watershed survey of the recharge area or zone of influence of subject source that
identifies and evaluates actual and potential sources of contamination, including any
reported discharge that may affect the source.
e) Based on the findings in item (d), a plan for special monitoring of any significant
contaminant source and for taking restrictive preventive or corrective measures as
appropriate to protect the source water.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 16.
3. It is a REQUIREMENT that a landuse assessment be conducted every 4 years by an
appropriately trained person, to assess changes in local landuse that may impact on an
underground source, where the water is sourced from an underground source.
4. It is a REQUIREMENT that the plant operator be responsible for sampling and analysis of all
approved sources for the contaminants specified in the Standard of Analytical Compliance.
5. Such monitoring is REQUIRED to be at the frequencies specified of the Standard of
Analytical Compliance.
6. In lieu of source monitoring required by this Section, a plant operator using a public water
system as its water supply is REQUIRED to obtain and display a certificate from said system
demonstrating that the public water system conducts the monitoring required.
7. Where a bottled water plant operator, water dealer, or regulatory agency knows or has
reason to believe that a contaminant not otherwise monitored is present in the source water
because of a spill, release of a hazardous substance, or otherwise, and its presence would
create a potential health hazard to consumers, the plant operator or water dealer upon receipt
of such information MUST monitor the source water for said contaminant.
8. Detection of contaminant(s) in source monitoring required pursuant to Section 8 MUST be
followed immediately by a program of periodic monitoring to confirm the presence in the
source water of said contaminant(s).
9. If such listed unregulated contaminant(s) is confirmed to be present in the source water at a
concentration that exceeds FSANZ requirements for bottled water, the plant operator or water
dealer MUST employ appropriate treatment techniques to remove or to reduce said
contaminant in the product water below said concentration, and MUST employ a program of
periodic monitoring for said contaminant in the source water until such time as said
contaminant is not detectable in the source water.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 17.
10. To assure that bottled water complies with Section 3, the monitoring, using representative
samples derived from the source, MUST be performed in accordance with the Standard of
Analytical Compliance.
11. For compliance purposes bottlers are REQUIRED to maintain documentation confirming
the location of the source.
12. When a non-compliance results (including where a test is not conducted) for any one of the
analytes, the bottler MUST conduct annual tests to re-establish a history of 2 consecutive
years with no non-compliances before returning to testing every 4 years, for that analyte/s.
3.2 Hygienic Production of Food Sources
3.2.1 Source Water
If any source does not comply with the Standard of Analytical Compliance for the production
of bottled water, the bottler MUST show by analysis, that this treatment reduces the
contaminants(s) below the Standard of Analytical Compliance in the finished product.
3.2.2 Finished Product
To assure that bottled water complies with Section 3, the product monitoring, using
representative samples derived from the bottled product MUST be performed in accordance
with the Standard of Analytical Compliance.
3.3 Handling, Storage and Transport
It is a REQUIREMENT that storage and transportation of finished food be under conditions
that will protect food against physical, chemical and microbial contamination as well as against
deterioration of the food and the container.
3.4 Cleaning, Maintenance & Personnel Hygiene at Primary Production
1.Site is REQUIRED to be compliant with Food Standards Code sections 3.2.2 and 3.2.3.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 18.
2. It is a REQUIREMENT that all persons working in direct contact with food, food-contact
surfaces and food-packaging materials conform to hygienic practices while on duty to the
extent necessary to protect against contamination of food. The gloves should be of an
impermeable material.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 19.
Section IV – Establishment: Design and Facilities
4.1 Location
Please refer to Food Standards Code 3.2.3 & Recommended International Code of Practice:
General Principles of Food Hygiene (CAC/RCP 1-1969, Rev. 3 (1997)).
4.2 Premises and Rooms
1. It is recommended that the bottling room separated from other plant operations or storage
areas by tight walls, ceilings and self-closing doors to protect against contamination.
2. It is REQUIRED that conveyor openings NOT exceed the size required to permit passage of
containers.
3. If processing operations are conducted in other than a sealed system under pressure,
adequate protection is REQUIRED to be provided to preclude contamination of the water and
the system.
4. Adequate ventilation is REQUIRED to minimise condensation in processing rooms, bottling
rooms and in container washing and sanitising areas.
5. It is recommended that the washing and sanitising of containers for bottled water be
performed in an enclosed room. It is REQUIRED that the washing and sanitising operations be
positioned within the room so as to minimise any possible post-sanitising contamination of the
containers before they enter the bottling room.
6. Rooms in which product water is handled, processed or held or in which containers, utensils
or equipment are washed or held MUST NOT open directly into any room used for domestic
household purposes.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 20.
4.3 Equipment
1. Storage tanks are REQUIRED to be of the type that can be closed to exclude all foreign
matter.
2. Storage tanks are REQUIRED to be adequately vented.
3. It is recommended that HEPA filtration be installed but care is essential to ensure sufficient
capacity of the filter to prevent tanks from being sucked in during discharge. Safety devices,
designed to prevent tanks from sucking in, may be used.
4.4 Facilities
Many bottled water companies conduct in-house testing, including micro-biological tests. It is
important that in-house laboratories are maintained in a clean, sanitary manner, so that no
contamination is introduced into water samples from the laboratory environment
This aims to guarantee the validity of the results obtained from tests conducted in-house.
In-house laboratories are REQUIRED to be maintained in a clean and appropriate manner for
the activities to be conducted without causing contamination by handling or an unsuitable
environment.
Site is REQUIRED to be compliant with Food Standards Code sections 3.2.2 and 3.2.3.
Laboratory maintenance will include:-
1. The construction, space, lighting and ventilation to be designed to conduct the required
activities.
2. All laboratory equipment is adequately sanitised and maintained in proper working order.
3. Appropriate sanitisation of the laboratory will be maintained.
4. Quality control monitoring will be conducted to ensure the reliability and efficacy of tests,
test results and laboratory personnel.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 21.
5. Calibration of equipment will be carried out as required for each piece of equipment.
6. Access will be restricted to authorised personnel.
7. Staff may only enter wearing clean outer clothing.
8. Rubbish will be kept covered and removed daily.
9. Procedures are documented and document control established for all laboratory operations
and records.
10. All contaminated materials are REQUIRED to be sterilised prior to disposal.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 22.
Section V – Control of Operation
5.1 Control of Food Hazards
Good Manufacturing Practices (GMP) is an integral part of the ABWI Model Code. GMP assists
bottlers in producing water of the required standard of safety and suitability for consumption
through design, implementation, monitoring and review of effective control systems.
Attention to GMP ensures that the best practices are implemented, to reduce risk by adopting
preventative measures to avoid unnecessary and costly practices.
When a bottled water plant is utilising a treatment technology in order to reduce the level of
any constituent in its source water below the ABWI Standard of Analytical Compliance, or to
prevent a contaminant from entering the product water in amounts that exceed the ABWI
Standard of Analytical Compliance, said treatment is to be operated in accordance with the
Good Manufacturing Practices set out in this section.
1. It is recommended that bottled water be produced in an enclosed filling room/chamber that
is under positive pressure of filtered air and using facilities and good manufacturing practices
that comply with the requirements of GMP and be properly maintained with supporting
records.
2. Bottled water production, including transporting, processing, packaging, and storage, is to
be conducted under such conditions and controls as are necessary to minimise the potential for
microbiological contamination of the finished product.
3. Bottled water is to be produced under one of the following conditions:- bottled water MUST
be subject to adequate filtration (to a minimum rating of at least 1 micron or lower) and
effective germicidal treatment by ozonation, carbonation at a minimum of three volumes of
carbon dioxide, or other proven disinfection regimes OR
4. Bottled water MUST be subject to adequate filtration (to a minimum rating of at least 1
micron or lower) and be produced in an enclosed fillroom/chamber that is under positive
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 23.
pressure, HEPA filtered air; and using facilities and good manufacturing practices that comply
with the requirements for GMP, set out in this Section.
5. Bottled water MUST NOT be transported or stored in bulk tanks, or processed or bottled
through equipment or lines used for any non-food product.
5.2 Key Aspects of Hygiene Control Systems
5.2.1 Treatment of Product Water
1. It is a REQUIREMENT that all treatment of product water by ozonation, distillation, ion-
exchanging, filtration, ultra-violet treatment, reverse osmosis, carbonation, mineral addition,
or any other process is done in a manner so as to be effective in accomplishing its intended
purpose.
2. All such processes MUST be performed in and by equipment and with substances that will
not adulterate the bottled product.
3. It is REQUIRED that a record of the type and date of physical inspections of such equipment,
conditions found and the performance and effectiveness of such equipment be maintained by
the plant.
4. Product water samples MUST be taken after processing and prior to bottling by the plant
and analysed as often as is necessary to assure uniformity and effectiveness of the processes
performed by the plant.
5. It is a REQUIREMENT that the methods of analysis be those approved by the government
agency or agencies having jurisdiction.
5.2.2 Containers
1. Multi-service primary containers MUST be adequately cleaned, sanitized and inspected just
prior to being filled, capped and sealed.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 24.
2. Containers found to be unsanitary or defective by the inspection MUST be reprocessed or
discarded.
3. All multi-service primary containers MUST be washed, rinsed and sanitised by mechanical
washers or by any other method giving adequate sanitary results.
4. Mechanical washers are REQUIRED to be inspected as often as is necessary to assure
adequate performance.
5. It is REQUIRED that records of physical maintenance, inspections and conditions found, and
performance of the mechanical washer be maintained by the plant.
6. Multi-service shipping cases MUST be maintained in such condition as to assure they will not
contaminate the primary container or the product water.
7. Adequate dry or wet cleaning procedures are REQUIRED to be performed as often as
necessary to maintain the cases in satisfactory condition.
5.2.3 Cleaning and Sanitising Solutions
1. It is REQUIRED that cleaning and sanitising solutions utilized by the plant be sampled and
tested by the plant as often as is necessary to assure adequate performance in the cleaning and
sanitizing operations.
2. It is REQUIRED that records of these tests be maintained by the plant.
5.3 Incoming Material Requirements
5.3.1 Air Under Pressure
1. Whenever air under pressure is directed at product water or a product water-contact surface,
it is a REQUIREMENT that it be free of oil, dust, rust, excessive moisture and extraneous
materials.
2. It is REQUIRED that it NOT affect the bacteriological quality of the water.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 25.
3. It is recommended that it NOT adversely affect the flavour, colour or odour of the water.
5.3.2 Bulk Water
1. It is REQUIRED that bulk water be from an approved source and maintained for sanitary
quality at all times.
2. Bottled water that originates from a source that is not protected from surface
contamination MUST be subjected to ozonation, filtration rated at one micron, or another
effective process which removes or destroys the cysts of the parasite Giardia lamblia and
Cryptosporidium.
3. Daily in-house total coliform monitoring on finished product MUST be done on each product
type.
4. It is recommended that quarterly rinse/swab tests be performed in-house or by a laboratory
using an approved methodology, on containers (incoming as well as those immediately from
the washer) and closures.
5.4 Packaging
1. During the process of filling, capping or sealing either single-service or multi-service
containers, it is a REQUIREMENT that the performance of the filler, capper or sealer be
monitored and the filled containers visually or electronically inspected to assure they are
sound, properly capped or sealed, and coded and labeled.
2. Containers that are not satisfactory MUST be reprocessed or rejected.
3. Bottlers MUST only use nontoxic containers and closures.
4. All containers and closures MUST be inspected to ascertain that they are free from
contamination. At least once each 3 months, it is recommended that a bacteriological swab
and/or rinse count be made from at least four containers and closures selected just prior to
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 26.
filling and sealing. No more than one of the four samples may exceed more than one bacteria
per millilitre of capacity or one colony per square centimetre of surface area.
5. All samples MUST be free of E. coli AND/OR coliform organisms. Refer to Standard of
Analytical Compliance.
6. The procedure and apparatus for these bacteriological tests are REQUIRED to be in
conformance with those recognized by the government agency or agencies having jurisdiction.
7. It is a REQUIREMENT that tests be performed either by trained plant personnel or by a
laboratory using approved methodologies.
8. It is a REQUIREMENT that all operations in the receiving, inspecting, transporting,
segregating, preparing, manufacturing, packaging and storing of food be conducted in
accordance with adequate sanitation principles.
9. It is a REQUIREMENT that overall sanitation of the plant be under the supervision of one or
more competent individuals assigned responsibility for this function.
10. It is a REQUIREMENT that all reasonable precautions be taken to ensure that production
procedures do not contribute contamination from any source.
11. It is a REQUIREMENT that chemical, microbial, or extraneous-material testing procedures
be used where necessary to identify sanitation failures or possible food contamination.
12. All food that has become contaminated to the extent that it is adulterated MUST be
rejected, or if permissible, treated or processed to eliminate the contamination.
5.5 Source and Operations Water
It is a REQUIRED that the product water supply for each plant be from an approved source
properly located, protected and operated and is REQUIRED to be easily accessible, adequate
and of a safe, sanitary quality which is REQUIRED to be in conformance at all times with the
applicable laws and regulations of the government agency or agencies having jurisdiction.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 27.
If different from the product water supply, the operations water supply MUST be obtained
from an approved source properly located, protected, and operated and MUST be easily
accessible, adequate, and of a safe, sanitary quality which MUST be in conformance at all
times with the applicable laws and regulations of the government agency or agencies having
jurisdiction.
5.6 Management and Supervision
A bottled water plant MUST be operated under the supervision of at least one person qualified
by experience, education, and training to operate and maintain the plant's facilities and holds
current ABWI Certified Plant Operator qualifications.
5.7 Documentation and Records
1.The objectives & rationale is to maintain sufficient records to comply with requirements and
to ensure that records are on hand to respond to authorities, when required
2. Legal requirements vary from jurisdiction to jurisdiction. Often waters are sold in various
jurisdictions.
3. It is a REQUIREMENT that all records be retained at the plant for not less than 7 years.
4. Various regulations exist across Australia and New Zealand. Hence ABWI is recommending
that all records be maintained for a minimum of 7 years. This includes records for HACCP
verification, monitoring and validation, process controls, production, cleaning and sanitizing,
training, customer complaints and any other records.
5.8 Recall Procedures
Where it is determined, based upon representative samples, risk analysis, information
provided by the bottled water supplier, and other information available that the circumstances
present an imminent hazard to the public health and that a form of consumer notice or product
recall can effectively avoid or significantly minimise the threat to public health, the bottler
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 28.
MUST initiate a product recall to be conducted in accordance with ABWI Product Recall
Procedures.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 29.
Section VI – Establishment: Maintenance and Sanitation
Cleaning and sanitation are important activities in a bottled water plant, involving all areas of
production. Effective cleaning and sanitising will prevent contamination of products and
maintain a clean and hygienic plant.
Effective and efficient cleaning and sanitising procedures ensures that process equipment and
factory environments are clean and free of contaminants to ensure products meet the required
standards
6.1 Maintenance and Cleaning
1. Site is REQUIRED to be compliant with Food Standards Code sections 3.2.2 in relation to
Food Safety Practices and General Requirements and 3.2.3.Food Premises and Equipment.
2. Cleaning compounds and sanitizing agents used in cleaning and sanitizing procedures MUST
be free from undesirable microorganisms and MUST be safe and adequate under the
conditions of use.
Compliance with these requirements may be verified by any effective means including
purchase of these substances under a supplier's guarantee or certification, or examination of
these substances for contamination. Only the following toxic materials may be used or stored
in a plant where food is processed or exposed:
a)Those required to maintain clean sanitary conditions;
b) Those necessary for use in laboratory testing procedures;
c) Those necessary for plant and equipment maintenance and operation; and
d) Those necessary for use in the plant operations.
3. Toxic cleaning compounds, sanitizing agents, and pesticide chemicals MUST be identified,
held and stored in a manner that protects against contamination of food, food-contact
surfaces or food-packaging materials. It is recommended that all relevant regulations from
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 30.
Federal, State and local government agencies for the application, use or holding of these
products be followed.
4. All food-contact surfaces including utensils and food-contact surfaces of equipment MUST
be cleaned as frequently as necessary to protect against contamination of food.
5. When the surfaces are wet-cleaned, it is a REQUIREMENT that, when necessary, they be
sanitized and thoroughly dried before subsequent use.
6. Where equipment and utensils are used in a continuous production operation, the utensils
and food-contact surfaces of the equipment MUST be cleaned and sanitized as necessary.
7. It is recommended that single-service articles (such as utensils intended for one-time use,
paper cups and paper towel(s) be stored in appropriate containers.
8. It is REQUIRED that single service items as described are handled, dispensed, used and
disposed of in a manner that protects against contamination of food or food-contact surfaces.
9. It is a REQUIREMENT that sanitising agents be adequate and safe under conditions of use.
Any facility, procedure or machine is acceptable for cleaning and sanitizing equipment and
utensils if it is established that the facility, procedure or machine will routinely render
equipment and utensils clean and provide adequate cleaning and sanitising treatment.
6.2 Cleaning Programs
1. The product water-contact surfaces of all multi-service containers, utensils, pipes and
equipment used in the transportation, processing, handling and storage of product water
MUST be clean and adequately sanitised.
2. All product water-contact surfaces MUST be inspected by plant personnel as often as
necessary to maintain the sanitary condition of such surfaces and to assure they are kept free
of scale, evidence of oxidation and other residue.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 31.
3. It is a REQUIREMENT that the presence of any unsanitary condition, scale, residue or
oxidation be immediately remedied by adequate cleaning and sanitising of that product water-
contact surface prior to use.
4. It is REQUIRED that after cleaning, all multi-service containers, utensils and disassembled
piping and equipment be transported and stored in such a manner as to assure drainage and it
is REQUIRED that they be protected from contamination.
5. It is REQUIRED that single-service containers and caps are to be purchased and stored in
sanitary closures and kept clean therein in a clean, dry place until used.
6. Prior to use single service containers and caps ARE REQUIRED to be examined and as
necessary, washed, rinsed and sanitized and MUST be handled in a sanitary manner.
7. Filling, capping, closing, sealing and packaging of containers MUST be done in a sanitary
manner so as to preclude contamination of the bottled water.
8. It is REQUIRED that all plant equipment and utensils be suitable for their intended use. This
includes all collection and storage tanks, piping, fittings, connections. Bottle washers, fillers,
cappers and other equipment which may be used to store, handle, process, package or
transport product water.
9. All product water contact surfaces MUST be constructed of nontoxic and nonabsorbent
material which can be adequately cleaned and sanitized.
10. Instruments and controls used for measuring, regulating or recording temperatures, pH,
acidity, water activity, or other conditions that control or prevent the growth of undesirable
microorganisms in food are REQUIRED to be accurate and adequately maintained, and
adequate in number for their designated uses.
10. Bottled water manufacturers who clean and/or refurbish coolers for re-sale or re-hire MUST
have a cleaning and sanitising procedure in place.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 32.
11. It is REQUIRED that these procedures include: isolate returned coolers from new or
sanitised coolers, clean and sanitise away from process areas where there can be no
contamination of raw materials, process lines or finished product, check, clean and sanitise the
coolers, repair as required, when completed the coolers will be bagged or boxed in a manner
that will minimise the risk of recontamination, store in an appropriate manner.
6.3 Pest Control Systems
Please refer to Recommended International Code of Practice: General Principles of Food
Hygiene (CAC/RCP 1-1969, Rev. 3 (1997)).
6.4 Waste Management
Please refer to Recommended International Code of Practice: General Principles of Food
Hygiene (CAC/RCP 1-1969, Rev. 3 (1997)).
6.5 Monitoring Effectiveness
1. For those bottlers who own a source and a bottling plant, finished product monitoring is all
that is required. Source water monitoring will not be required, aside from hydrogeological
requirements as outlined in the Standard of Analytical Compliance.
2. To assure that bottled water complies with Section 3 (Product Quality), it is REQUIRED that
the testing requirements stipulated in the Standard of Analytical Compliance of this Code are
followed, using representative samples derived from the bottled product.
3. Bottlers who have established history of compliance with the requirements for testing and
meeting the limits set for organics (listed in Section XI Standard of Analytical Compliance) of a
representative sample of finished product water, over 2 consecutive years, may then carry out
tests for organics and volatile organics every 4 years.
4. It is recommended that bottlers conduct in-house yeast and mould tests at least once per
week on a sample of each type of finished product.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 33.
5. It is recommended that bottlers conduct in-house Pseudomonas aeruginosa tests at least
once per week on a sample of each type of finished product.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 34.
Section VII – Establishment: Personal Hygiene
7.1 Health Status
Please refer to Australian New Zealand Food Standards Code 3.2.2, Division 4 and
Recommended International Code of Practice: General Principles of Food Hygiene (CAC/RCP
1-1969, Rev. 3 (1997)).
7.2 Illness and Injuries
Please refer to Australian New Zealand Food Standards Code 3.2.2, Division 4 and
Recommended International Code of Practice: General Principles of Food Hygiene (CAC/RCP
1-1969, Rev. 3 (1997)).
7.3 Personal Cleanliness
Please refer to Australian New Zealand Food Standards Code 3.2.2, 3.2.3, Division 4 and
Recommended International Code of Practice: General Principles of Food Hygiene (CAC/RCP
1-1969, Rev. 3 (1997)).
7.4 Personal Behaviour
Please refer to Australian New Zealand Food Standards Code 3.2.2, 3.2.3, Division 4 and
Recommended International Code of Practice: General Principles of Food Hygiene (CAC/RCP
1-1969, Rev. 3 (1997)).
7.5 Visitors
Please refer to Australian New Zealand Food Standards Code 3.2.2, 3.2.3, Division 4 and
Recommended International Code of Practice: General Principles of Food Hygiene (CAC/RCP
1-1969, Rev. 3 (1997)).
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 35.
Section VIII – Transportation
8.1 General
Please refer to Recommended International Code of Practice: General Principles of Food
Hygiene (CAC/RCP 1-1969, Rev. 3 (1997)).
8.2 Requirements
1. It is a REQUIREMENT that bulk water be loaded, transported and unloaded in a sanitary
manner to ensure the overall safety and quality of the finished bottled water product.
2. It is a REQUIREMENT that bulk water tankers, storage tanks, hoses, pumps and
connections used for loading, transporting and unloading of bulk water be constructed of
materials that are approved food-grade, smooth, non-absorbent and easily cleanable such as
stainless steel (300 series).
3. It is recommended that tankers used for the hauling of bulk water bottling purposes be
solely dedicated for that purpose. If the tanker is used for transporting other foods, it is a
REQUIREMENT that the tanker be properly cleaned and sanitised in accordance with the GMP
regulations before the loading of a bulk shipment of potable water intended for human
consumption.
4. It is a REQUIREMENT that tankers be cleaned, sanitised and inspected internally for tank
integrity on a routine basis.
5. Tankers that have been previously used to haul non-food commodities such as toxic
materials, petroleum products, or other harmful substances MUST NOT be used to haul
bottled water for human consumption.
6. It is a REQUIREMENT that tankers used for the transporting of potable water be properly
secured with manhole cover gaskets and safety seals.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 36.
7. It is REQUIREMENT that connections, hoses and pumps used for the loading and unloading
of bulk water be properly maintained and stored to prevent contamination.
8. When not in use, pumps, hoses, connections and fittings are REQUIRED to be properly
capped, securely stored and protected from possible contamination.
9. Representative samples MUST be taken from shipments of bulk water for the analyses of
coliform bacteria and Heterotrophic Plate Count (HPC), in compliance with the Standard of
Analytical Compliance.
10. It is a REQUIREMENT that the minimum frequency of sampling is one sample from each
tanker on a weekly basis or from each delivery if the delivery frequency is less than weekly.
This data will be collected and used to identify a gradual or sudden increase in HPC, indicating
some form of contamination is taking place to allow the bottler to investigate.
11. Records are REQUIRED to be maintained that include but are not limited to:
a) Name of the transporter and/or driver
b) Tanker number
c) Date of shipment
d) Vendor and location of the source water
e) Name of the receiver and the location to which the water was shipped
f) Date of delivery
g) Date of tanker cleaning and sanitisation (includes name of operator)
h) The concentration of the disinfectant residual (if used) at the time of loading and
unloading
i) Results of all microbiological testing as specified.
12. It is REQUIRED that, in order to minimise the potential for microbiological contamination
of the finished product, bottled water NOT be transported, stored, processed, or bottled in or
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 37.
through lines or equipment through which has passed milk, fruit juice, or other food products
likely to contribute nutrients for microbial growth, unless said lines, equipment, or holding
tanks have been cleaned in accordance with section 18, 19 of this section.
13. Bottled water may be processed through lines or equipment used also for other food
products under the following conditions:
a) It is REQUIRED that process lines, including storage tanks and associated
equipment, be used exclusively for the production of bottled water, except for filling
equipment, which may be used also for filling, other food products.
b) Before being used for the bottling of water, it is a REQUIREMENT that filling
equipment which is designed to be cleaned in-place and which is used for filling
other food products be thoroughly cleansed and sanitised in-place in accordance
with the manufacturer's specifications and in compliance with GMP and the
supplementary procedures that follow in this section.
c) Immediately following completion of filling operations for any other food product
other than water, it is REQUIRED that the filler be thoroughly rinsed internally and
externally with potable water meeting Australian Drinking Water Guidelines (N.B.
Chlorinated water, at 1-3 ppm, is NOT potable).
d) It is a REQUIREMENT that in accordance with filler manufacturer's instructions, any
parts that are not designed to be cleaned in-place be disassembled and removed. All
of these parts MUST be cleansed and sanitised prior to reassembly using appropriate
cleaning and sanitizing procedures, as specified below.
e) Sanitising operations, including those performed by chemical means or by any other
means such as circulation of live steam or hot water, MUST be adequate to effect
sanitisation of the intended product water-contact surfaces and any other critical
area.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 38.
14. It is recommended that the plant maintain a record of the intensity of the sanitising agent
and the time duration that the agent was in contact with the surface being sanitized. It is
REQUIRED that the following times and intensities be considered a minimum.
a) Steam in enclosed system: At least 76.6° C for at least 15 minutes or at least 93.3° C
for at least 5 minutes OR
b) Hot water in enclosed system: At least 76.6° C for at least 15 minutes or at least 93.3°
C for at least 5 minutes OR
c) Chemical sanitizers are REQUIRED to be equivalent in bacterial action to a minute
exposure of 50 parts per million of available chlorine at 13.9° C when used as an
immersion or circulation solution. Chemical sanitizers applied as a spray or fog
MUST have as minimum 100 parts per million of available chlorine at 13.9° C or its
equivalent in bactericidal action. OR
d) 0.1 part per million ozone water solution in an enclosed system for least 5 minutes
with consideration being given to the organic load and temperature of the water.
15. It is REQUIRED that all surfaces of the filler that do not contact food products be cleaned
manually so as to render all surfaces clean and free of any residues.
16. It is a REQUIREMENT that the filler be prepared and all appropriate connections made in
accordance with the filler manufacturer's instructions to place the filler in the clean-in-place
mode. The following procedures will be followed:
17. If using an alkaline cleaning solution, the appropriate strength MUST be re-circulated
through the filler to provide effective cleaning of all product contact surfaces, with a minimum
re-circulation time of 20 minutes at a temperature between 60 and 75 degrees Centigrade.
Alternatively a proven acid cleaning solution with an appropriate method as recommended by
the supplier, may be used.
18. The cleaning solution MUST be drained and followed with a potable water rinse-to-drain;
or otherwise removed from the system; for the removal of all residual cleaner alkalinity. This
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 39.
step may be supplemented by the application of an acidified rinse prior to the potable water
rinse in order to neutralise any residual alkalinity on product contact surfaces.
19. Following reassembly of all parts to place the filler into the product mode and just prior to
bottling water, the filler MUST be sanitised in-place in accordance with procedures in this
section.
20. Alternate cleaning, rinsing, or sanitising operations or processes not described in this
Section MUST be consistent with Australian or New Zealand regulatory requirements.
8.3 Use and Maintenance
Please refer to Recommended International Code of Practice: General Principles of Food
Hygiene (CAC/RCP 1-1969, Rev. 3 (1997)).
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 40.
Section IX – Product Information and Consumer Awareness
9.1 Lot Identification
Please refer to Recommended International Code of Practice: General Principles of Food
Hygiene (CAC/RCP 1-1969, Rev. 3 (1997)).
9.2 Product Information
Please refer to Recommended International Code of Practice: General Principles of Food
Hygiene (CAC/RCP 1-1969, Rev. 3 (1997)).
9.3 Labelling
1. Bottled water product labeling MUST comply with all applicable provisions under FSANZ
Food Standards Code and Appendices. The Joint Australia New Zealand Food Standards Code
(FSC) is administered by FSANZ and sets down mandatory labelling requirements.
2. Bottled water product labeling MUST comply with the provisions of the FSANZ Code of
Practice on Nutrient Claims in Food Labels and in Advertisements.
3. Bottled Water product labeling MUST also be in accordance with the Australian Competition
and Consumer Commission (ACCC) who are responsible for bringing about compliance with
the Australian Consumer Law 2010.
4. Bottled water product labeling MUST also comply with applicable provisions set out in
National Trade Measures Regulations 2009 administered by the National Measurement
Institute (NMI).
5. Bottled water product labeling MUST also comply with applicable provisions set out in the
Australian National Standard for Organic & Biodynamic Products (DR08147), administered by
Organic Federation of Australia (OFA) and Department of Agriculture, Forestry and Fisheries
(DAFF).
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 41.
6. Bottled water product labeling, where manufactured outside of Australia and New Zealand
MUST comply with local legislative provisions in addition to requirements in Australia and New
Zealand.
7. Where water is neither bottled nor sold in Australia and /or New Zealand, the requirements
of equivalent local regulation applies
8. For information on the current requirements of the Food Standards Code, bottlers may
contact FSANZ at:
Food Standards Australia New Zealand (FSANZ)
55 Blackall Street Barton ACT 2600
Canberra MC ACT 2610 Ph. 02 6271 2222 Fax 02 6271 2278
9.4 Consumer Information
Please refer to Recommended International Code of Practice: General Principles of Food
Hygiene (CAC/RCP 1-1969, Rev. 3 (1997)).
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 42.
Section X – Training
10.1 Awareness and Responsibilities
Please refer to Recommended International Code of Practice: General Principles of Food
Hygiene (CAC/RCP 1-1969, Rev. 3 (1997)) and Australian New Zealand Food Standards Code.
10.2 Training Programs
Said person operating the plant MUST hold a certificate demonstrating that he or she has
successfully completed the ABWI Certified Plant Operator course and be on site at all times
during product manufacture. This requirement is to be implemented as of the 1st January
2006. The person supervising a plant will be that person responsible for the development and
maintenance of processes and procedures.
This course may be conducted by ABWI or by a third party organisation that is acceptable to
ABWI. This course covers periodic instruction and testing in plant, source and product
sanitation, operation and maintenance of water treatment technology, and the maintenance
and monitoring of source and product water quality in accordance with these bottled water
standards.
10.3 Instruction and Supervision
Please refer to Recommended International Code of Practice: General Principles of Food
Hygiene (CAC/RCP 1-1969, Rev. 3 (1997)).
10.4 Refresher Training
Successful refresher examination of Certified Plant Operator qualifications must be revisited
no later than three years post previous review, by approved ABWI examination.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 43.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 44.
Section XI - Standard of Analytical Compliance
The Standard of Analytical Compliance (the Standard) seeks to ensure that the source water
and finished product meet criteria that minimise the risk of hazard from biological, chemical or
physical contaminants in the finished product.
All bottled water MUST be from an Approved Source, and MUST meet the Standard for source
testing. If any source does not comply with the Standard, the bottler MUST show by analysis
that the treatment reduces the contaminant(s) below the Standard in the finished product.
Bottlers MUST have a Hazard Analysis Critical Control Point (HACCP) program in their plants
which is audited and certified by accredited third party.
Note with regard to testing summary below -
1. Members that provide source water need to perform all required tests on source water
used for ALL types of finished products.
2. Members who own a bottling plant need complete to ALL required tests in testing
summary on finished product.
3. Those members owning both a source and bottling plant need to complete ALL required
tests in testing summary on finished product.
11.1 Testing Summary
Test Requirements Source* Tanker Finished Product
Hydrogeology - see page 4
Hydrogeological study Every four years, external
Microbiology – see page 5
Total Plate Count Weekly in house, or with
each delivery if deliveries
are less often than weekly
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 45.
Coliforms AND/OR
Escherichia coli
Weekly, external, or with
each load taken, if taken
less often than weekly OR
Monthly external, in
conjunction with daily in-
house
Weekly in house, or with
each delivery if deliveries
are less often than weekly
Daily in-house, in
conjunction with
monthly external
Yeasts and Moulds Weekly in-house
RECOMMENDATION
Pseudomonas
aeruginosa OR
Heterotophic Plate
Count
Weekly in-house
RECOMMENDATION
Chemistry – see page 7
Physical Annual, external Annual, external
Radiological Every four years, external
Inorganics Annual, external Annual, external
Organics and Volatile
Organics
Every four years once a
history of two years
compliance has been
established
Every four years once a
history of two years
compliance has been
established
* Source testing only necessary when finished product testing is not being undertaken, and source certification is required.
11.2 Hydrogeology of Source
Approval of the source water product derived from a source other than a public water supply
MUST be based upon a field inspection of the source, and a review of information prepared by
a professionally qualified hydrogeologist. This review MUST demonstrate the integrity of the
source and safety of the catchment operations, and that MUST include:
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 46.
a) An evaluation of the chemical, physical, microbiological, and radiological characteristics
of the source.
b) A report on the regional geology surrounding the site and the specific site geology. A
description of the vertical and horizontal extent of the source aquifer, using existing
data. The information will be used to define the recharge area of the aquifer, or in the
case of regional aquifers, the zone of influence of the subject source.
c) A report detailing the development of the source; the method of construction including
spring design, well installation, surface catchment, and intake structures; and
transmission facilities as appropriate.
d) A watershed survey of the recharge area or zone of influence of subject source that
identifies and evaluates actual and potential sources of contamination, including any
reported discharge that may affect the source.
e)Based on the findings in item (d), a plan for special monitoring of any significant
contaminant source and for taking restrictive preventive or corrective measures as
appropriate to protect the source water.
It is a REQUIREMENT that a land-use assessment be conducted every 4 years by an
appropriately trained person, to assess changes in local land-use that may impact on an
underground source, where the water is sourced from an underground source.
It is a REQUIREMENT that the plant operator be responsible for sampling and analysis of all
approved sources for the contaminants specified in the Standard of Analytical Compliance.
Such monitoring is REQUIRED to be at the frequencies specified.
In lieu of source monitoring required by this Section, a plant operator using a public water
system as its water supply is REQUIRED to obtain and display a certificate from said system
demonstrating that the public water system conducts the monitoring required.
Where a bottled water plant operator, water dealer, or regulatory agency knows or has reason
to believe that a contaminant not otherwise monitored is present in the source water because
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 47.
of a spill, release of a hazardous substance, or otherwise, and its presence would create a
potential health hazard to consumers, the plant operator or water dealer upon receipt of such
information MUST monitor the source water for said contaminant.
Detection of contaminant(s) in source monitoring required pursuant to Section 10 MUST be
followed immediately by a program of periodic monitoring to confirm the presence in the
source water of said contaminant(s). If such listed unregulated contaminant(s) is confirmed to
be present in the source water at a concentration that exceeds FSANZ requirements for
bottled water, the plant operator or water dealer MUST employ appropriate treatment
techniques to remove or to reduce said contaminant in the product water below said
concentration, and MUST employ a program of periodic monitoring for said contaminant in
the source water until such time as said contaminant is not detectable in the source water.
To assure that bottled water complies with Section 3 (Product Quality), the testing
requirements for coliform, inorganics, physical, radiological, organics and volatile organics of
the Code should be followed, using representative samples derived from the source.
For compliance purposes bottlers are REQUIRED to maintain documentation confirming the
location of the source.
Water source owners who have established a history of compliance with the requirements for
testing and meeting the limits set for organics and volatile organics of a representative sample
of source water, over 2 consecutive years, may then carry out tests for organics and volatile
organics every 4 years. When a non-compliance results (including where a test is not
conducted) for any one of the analytes, the bottler MUST conduct annual tests to re-establish
a history of 2 consecutive years with no non-compliances before returning to testing every 4
years, for that analyte/s.
11.3 Microbiology
11.3.1 Source Water Microbiological Limits
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 48.
Members that bottle their source water need only perform required tests on finished product,
however source water supplier members must undertake microbiological tests if they
distribute their product by tanker directly to customers or require independent source
certification.
Testing at the source is required to be undertaken at regular intervals and utilizing
representative samples. A representative sample may be identified by that which reflects
characteristics of each entire batch, and takes into consideration appropriate sample size and
frequency.
Coliforms must be tested
a)weekly, external, or with each load taken if taken less often than weekly or
b)monthly external in conjunction with daily in- house.
Tabulated below,
n means the minimum number of sample units.
c means the maximum allowable number of defective sample units, defective sample unit means a sample unit in which a microorganism is detected in a sample unit of a food at a level greater than m.
m means the acceptable microbiological level and
M means the level when exceeded in one or more samples would cause the lot to be
rejected.
Table 1 – Microbiological Testing Requirements for Source Water*
Organism n c m M*
REQUIRED E. coli AND/OR
coliforms
3 0 0 0
*Note: On occasion of external analysis being positive the bottler must revert to weekly
external testing until four consecutive absence results are achieved. The bottler must continue
daily in-house coliform tests.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 49.
Table 2 – Microbiological Testing Requirements for Tanker Water
Organism n c m M*
REQUIRED Total Plate Count 3 0 0 0
REQUIRED E. coli AND/OR coliforms 3 0 0 0
11.3.2 Bottled Water Microbiological Limits
Representative samples are required for testing daily in-house, in conjunction with monthly
external testing. Two additional tests, being yeasts and moulds and P. aeruginosa or
heterotrophic plate count are recommended subject to validation and verification procedures
in house.
Table 3 – Microbiological Testing Requirements for Bottled Water*
Organism n C m M*
REQUIRED E. coli AND/OR
coliforms
3 0 0 0
RECOMMENDATION Yeasts and
moulds
3 - - -
RECOMMENDATION Pseudomonas
aeruginosa OR
Heterotrophic
Plate Count
3 - - -
*Note: On occasion of external analysis being positive the bottler must revert to weekly
external testing until four consecutive absence results are achieved. The bottler must continue
daily in-house coliform tests.
11.4 Chemistry
11.4.1 Physical Properties of Bottled and Source Water
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 50.
These physical parameters are for aesthetic values and the limits are provided for guidance
only.
Table 4 – Physical Properties
Attribute Maximum Indicative
Colour < 5 units
Turbidity < 0.5 NTU
pH 3.5 - 8.5
Odour 3 T.O.N.
TDS minimum of 250 ppm for mineral water
11.4.2 Radionuclide Testing of Source Water
Table 5 – Standard for Radionuclide Testing of Source Water
Attribute Limit
*Gross Alpha 15 pCi/L
**Gross Beta 50 pCi/L
Radionuclide testing for source water is required every four years.
Please note the below conversion method to convert pCi/L to mBq/L
pCi/L (picocurie per liter) multiply (X) 0.037 to obtain = Bq/L (becquerel per liter)
* If Gross Alpha is greater than 5, analyze for Radium 226 and Radium 228. Their total should
not exceed 5 pCi/L.
** If Gross Beta is greater than 8 pCi/L, analyze for Strontium 90. If Gross Beta is greater than
50 pCi/L, analyze for Tritium and other man-made nuclides.
11.4.3 Inorganic Compounds in Source or Bottled Water
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 51.
Table 6 - Maximum Contaminant Level Inorganic Compounds (mg/L)
ANALYTE CAS Number ABWI LIMIT ** 4th
Ed WHO DWG + FSANZ
Antimony 7440-36-0 0.006 0.02
Arsenic 7440-38-2 0.05 0.01
Barium 7440-39-3 1.0 0.7
Beryllium 7440-41-7 0.004 NA
Borate (calculated as H3 BO3) 7440-42-8 30 NA
Bromate 7789-38-0 (Na) 7758-01-2 (K)
0.02 0.01
Cadmium 7440-43-9 0.005 0.003
Chloramine 10599-90-3 NA
Chloride * 16887-00-6
250.0 NA
Chlorine (free) NA <0.1 NA
Chlorite 14998-27-7 0.7
Chromium 7440-47-3 0.05 0.05
Copper * 7440-50-8 1.0 2.0
Cyanide 57-12-5 0.1 NA
Fluoride (Calculated as F-) 16984-48-8 1.5 1.0****
Iron * 8053-60-9 0.3 0.3
Lead 7439-92-1 0.005 0.01
Manganese * 7439-96-5 0.05 0.05
Mercury 7439-97-6 0.001 0.006
Molybdenum 7439-98-7 NA
Nickel 8049-31-8 0.1 NA
Nitrate 122019-28-7 10.0 (as N) 50
Nitrite 14797-65-0 1.0 (as N) 3
Organic matter (KMnO3 digested as O2) NA 3.0 3.0
Selenium 7782-49-2 0.01 0.04
Silver *** 97161-97-2 0.025 NA
Sulphate * 18785-72-3 250.0 NA
Sulphide (calculated as H2S) 18496-25-8 0.05 0.05
Thallium 82870-81-3 0.002 NA
Zinc * 7440-66-6 5.0 NA
* These compounds are classified as aesthetic, non-health related.
**The ABWI limit listed is the lowest limit of either the ABWI and FSANZ regulations.
*** As per WHO guidelines there is inadequate data to permit derivation of health- based guideline value
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 52.
****As per FSANZ adopted level (not official level for WHO)
11.4.4 Organic Compounds in Bottled or Source Water
Table 7 - Maximum Contaminant Level Organic Compounds (mg/L)
ANALYTE CAS NUMBER ABWI LIMIT FSANZ LIMIT
Di(2-ethylhexyl)adipate 70147-21-6 0.4 NA
Alachlor 15972-60-8 0.002 0.02
Atrazine 1912-24-9 0.003 0.1
Benzo(a)pyrene 50-32-8 0.0002 0.0007
Carbofuran 1563-66-2 0.007* 0.007
Chlordane 57-47-9 or 12789-03-6
0.0002* 0.0002
Dalapon (2,2-dichloropropanoic acid)
75-99-0 0.2 NA
Dibromochloropropane 96-12-8 0.0002 0.001
Dinoseb (2-butan-2-yl-4,6-dinitrophenol)
89396-94-1 0.007 NA
2,3,7,8-Tetrachlorodibenzo-p-dioxin (TCDD, dioxin)
1746-01-6 3x10-8
Diquat 2764-72-9 or 85-007
0.02 NA
Endothall 145-73-3 0.1 NA
Endrin 72-20-8 0.0002 0.0006
Glyphosate 1071-836 0.7 NA
Hexachlorobenzene 118-74-1 0.001 NA
Hexachlorocyclopentadiene 77-47-4 0.05 NA
Lindane 58-89-9 0.0002 0.002
Methoxychlor 72-43-5 0.02* 0.02
Oxamyl (vydate) 23135-220 0.2 NA
Pentachlorophenol 87-86-5 0.001 0.009
Di(ethylhexyl)phthalate 82208-43-3 0.006 0.008
Picloram 1918-02-1 0.5 NA
Simazine 122-34-9 0.002* 0.002
Toxaphene 101053-41-2 0.003
2,4-D (dichlorophenoxy acetic acid)
120-365 or 15165-670
0.03* 0.03
Ethylene dibromide 80-97-7 0.00005
Heptachlor 76-44-8 0.0004 NA
Heptachlor epoxide 1024-57-3 0.0002
(PCB) polychlorinated biphenyls
0.0005
2,4,5-TP (silvex) 93-72-1 0.009* 0.009
Phenolics 0.001
*Revised ABWI Limits, 2013
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 53.
11.4.5 Volatile Organic Compounds in Bottled or Source Water
Table 8 - Maximum Contaminant Level Volatile Organic Compounds (mg/L)
ANALYTE CAS Number ABWI LIMIT FSANZ LIMIT
Trichloroethylene 79-01-6 0.005 0.02
Carbon tetrachloride 0.004* 0.004
Vinyl chloride 0.0003* 0.0003
1,2-Dichloroethane 107-06-2 0.005 0.05
Benzene 0.005 0.01
1,1,-Dichloroethylene 0.007 NA
1,1,1,-Trichloroethane 71-55-6 0.200
1,2,4-Trichlorobenzene 120-82-1 0.07 NA
1,1,2-Trichloroethane 79-00-5 0.005
o-Dichlorobenzene 0.600
p-Dichlorobenzene 0.075 0.3
Cis-1,2-Dichloroethylene 540-59-0 0.050* 0.05
trans-1,2-Dichloroethylene 0.100
1,2-Dichloropropane 78-87-5 0.005 0.04
Ethylbenzene 100-41-4 0.3* 0.3
Dichloromethane 75-09-2 0.005 0.02
Monochlorobenzene 0.100
Styrene 100-42-5 0.02* 0.02
Tetrachloroethylene 127-18-4 0.005 0.04
Trihalomethane 0.010
Toluene 108-88-3 0.7* 0.7
Xylene 1330-20-7 0.5* 0.5
*Revised ABWI Limits, 2013
11.4.6 Additional Volatile Organic Compound Screening in Source or Bottled
Water
The following compounds are also detected as part of the screening test for Volatile Organic
Compound analysis. These chemicals are part of the audit code in addition to the FSANZ
adopted limits in the WHO Drinking Water Guidelines 4th Edition.
Table 9 – Additional Volatile Organic Compound Screening
Compound CAS
Bromobenzene 108-86-1
Bromochloromethane 83847-49-8
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 54.
Bromodichloromethane 75-27-4
Bromoform 75-25-2
Bromomethane 74-83-9
Butylbenzene,n-
Butylbenzene,sec- 68411-44-9
Butylbenzene,tert-
Chlorodibromomethane 124-48-1
Chloroethane 77792-41-7
Chloromethane 74-87-3
Chlorotoluene,o- 27987-13-9
Chlorotoluene,p-
Dibromomethane 74-95-3
Dichlorodifluoromethane 75-71-8
Dichloroethane,1,1- 75-34-3
Dichloropropane,1,3- 142-28-9
Dichloropropane,2,2- 594-20-7
Dichloropropene,1,1-
Dichloropropene,cis-1,3-
Dichloropropene,trans-1,3- 99614-02-5, 542-75-6
Fluorotrichloromethane 91315-61-6, 75-69-4
Hexachlorobutadiene 87-68-3
Isopropyltoluene,p- 99-87-6
Methyl-Ethyl-Ketone
Naphthalene 91-20-3
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 55.
Propylbenzene,iso-
Propylbenzene,n- 103-651
Tetrachloroethane,1,1,1,2-
Tetrachloroethane,1,1,2,2-
Trichlorobenzene,1,2,3- 87-61-6
Dichlorobenzene,m-
Trichloropropane,1,2,3-
Trichlorotrifluoroethane 76-13-1
Trimethylbenzene,1,2,4- 95-63-6
Trimethylbenzene,1,3,5- 108-67-8
CAS obtained from chemindustry.com and commonchemistry.org.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 56.
Section XII – Model Code Checklist
The following check points have been extracted from the body of the Model Code.
Further detail on each point may be obtained from the relevant Section of the Code.
Bottlers should note:-
The Code requires compliance with a number of MUST and REQUIRED points. Full
compliance is required.
For those points that are REQUIRED non-conformance may be avoided by demonstration of
measures of validation and/or verification.
12.1 Introduction
Source owners may seek separate Source Certification. In this event they MUST meet the
requirements for an approved source.
Approved sources MUST also carry out the annual testing regime. Source owners should refer
to the summary of testing.
12.2 Definitions and Acronyms
ABWI Members are REQUIRED comply with the definitions described.
The bottler MUST maintain in the plant a current license or certificate of approval of the source
where issued (by state or department).
Groundwater MUST not be under the direct influence of surface water.
It is a REQUIREMENT that mineral water have a level of total dissolved solids of greater than
250 ppm.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 57.
12.3 Product Quality
1. All bottled water MUST meet the Standard of Analytical Compliance for source testing, as
prescribed in limits specified therein.
2. Bottlers MUST implement a third party audited HACCP program in their plants.
3. For inclusion in the list, the hazard MUST be of such a nature that its prevention, elimination
or reduction to acceptable levels is essential to the production of a safe food.
4. All significant hazards identified during the hazard analysis MUST be addressed.
5. All three types of hazards (physical, chemical and biological, including microbiological)
MUST be addressed and controlled.
6. It is recommended that the information developed during the hazard analysis enable the
establishment to identify which steps in their processes are CCP's.
7. It is a REQUIREMENT that all CCP'S be carefully developed and documented.
8.A critical limit is defined as a criterion that MUST be met for each preventive measure
associated with a CCP.
9. Established critical limits MUST be justifiable in relation to knowledge available.
10. Fillers need to identify critical limits in their HACCP plans that MUST be met at each CCP to
be certain that the hazard is controlled.
11. Critical limits MUST reflect relevant regulations.
12. If critical limits more stringent than regulatory limits or requirements are set, then the
establishment is REQUIRED to meet those more stringent limits.
13. Monitoring is used to determine when a deviation occurs at a CCP; therefore, monitoring
procedures are REQUIRED to be effective.
14. When continuous monitoring is not feasible, frequencies MUST be sufficient to ensure that
the CCP is under control.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 58.
15. It is REQUIRED that personnel assigned to monitoring activities be properly trained and
assessed for competence to report all results, including any unusual occurrences, so that
adjustments can be made and any processes or products that do not meet critical limits are
identified so that immediate corrective actions may be taken.
16. In such instances, corrective action plans MUST be in place to (1) determine the disposition
of the non-compliant product and (2) identify and correct the cause of the deviation to regain
control of the CCP.
17. Corrective actions MUST be specified in sufficient detail to ensure that no public health
hazard exists after these actions have been taken.
18. It is a REQUIREMENT that a bottlers HACCP plan and all associated records be maintained
on file at the establishment and provides several examples of records that could be
maintained, such as those relating to incoming ingredients, product safety, processing,
packaging, storage and distribution, deviations and corrective actions and employee training.
19. Thus, a HACCP plan is REQUIRED to provide for a record keeping system that will
document the establishment's CCP monitoring, verification activities and deviation records.
20. It is REQUIRED that establishments frequent review their HACCP plan, verification that
the HACCP plan is being correctly followed, review of CCP records and determinations that
appropriate management decisions and product dispositions are made when deviations occur.
21. It is REQUIRED that such reviews include an on-site review and verification of all flow
diagrams.
22. It is REQUIRED that the HACCP system includes a set of verification tasks to be performed
by establishment personnel.
12.4 Good Manufacturing Practices
1. It is recommended that bottled water be produced in an enclosed filling room/chamber that
is under positive pressure of filtered air and using facilities and good manufacturing practices
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 59.
that comply with the requirements of GMP and be properly maintained with supporting
records.
2. Bottled water MUST be subject to adequate filtration (to a minimum rating of at least 1
micron or lower) and effective germicidal treatment by ozonation, carbonation at a minimum
of three volumes of carbon dioxide, or other proven disinfection regimes OR bottled water
MUST be subject to adequate filtration (to a minimum rating of at least 1 micron or lower) and
be produced in an enclosed fillroom/chamber that is under positive pressure, HEPA filtered air;
and using facilities and good manufacturing practices that comply with the requirements for
GMP, set out in this Section.
3. Bottled water MUST NOT be transported or stored in bulk tanks, or processed or bottled
through equipment or lines used for any non-food product.
4. It is REQUIRED that bulk water be from an approved source and maintained for sanitary
quality at all times.
5. It is a REQUIREMENT that bulk water be loaded, transported and unloaded in a sanitary
manner to ensure the overall safety and quality of the finished bottled water product.
6. It is a REQUIREMENT that bulk water tankers, storage tanks, hoses, pumps and
connections used for loading, transporting and unloading of bulk water be constructed of
materials that are approved food-grade, smooth, non-absorbent and easily cleanable such as
stainless steel (300 series).
7. It is recommended that tankers used for the hauling of bulk water bottling purposes be
solely dedicated for that purpose.
8. If the tanker is used for transporting other foods, it is a REQUIREMENT that the tanker be
properly cleaned and sanitised in accordance with the GMP regulations immediately before
the loading of a bulk shipment of potable water intended for human consumption.
9. It is a REQUIREMENT that tankers be cleaned, sanitised and inspected internally for tank
integrity on a routine basis.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 60.
10. Tankers that have been previously used to haul non-food commodities such as toxic
materials, petroleum products, or other harmful substances MUST NOT be used to haul
bottled water for human consumption.
11. It is a REQUIREMENT that tankers used for the transporting of potable water be properly
secured with manhole cover gaskets and safety seals.
12. It is REQUIREMENT that connections, hoses and pumps used for the loading and
unloading of bulk water be properly maintained and stored to prevent contamination.
13. When not in use, pumps, hoses, connections and fittings are REQUIRED to be properly
capped, securely stored and protected from possible contamination.
14. Representative samples MUST be taken from shipments of bulk water for the analyses of
coliform bacteria and Heterotrophic Plate Count (HPC).
15. It is a REQUIREMENT that the minimum frequency of sampling is one sample from each
tanker on a weekly basis or from each delivery if the delivery frequency is less than weekly.
16. Records are REQUIRED to be maintained as specified in Section 12 that include but are not
limited to:
(a) Name of the transporter and/or driver
(b) Tanker number
(c) Date of shipment
(d) Vendor and location of the source water
(e) Name of the receiver and the location to which the water was shipped
(f) Date of delivery
(g) Date of tanker cleaning and sanitisation (includes name of operator)
(h) The concentration of the disinfectant residual (if used) at the time of loading and unloading
(i) Results of all microbiological testing as specified.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 61.
17. It is REQUIRED that, in order to minimise the potential for microbiological contamination
of the finished product, bottled water NOT be transported, stored, processed, or bottled in or
through lines or equipment through which has passed milk, fruit juice, or other food products
likely to contribute nutrients for microbial growth, unless said lines, equipment, or holding
tanks have been cleaned in accordance with subpart (d) of this Section.
18. It is REQUIRED that process lines, including storage tanks and associated equipment, be
used exclusively for the production of bottled water, except for filling equipment, which may
be used also for filling, other food products.
19. Before being used for the bottling of water, it is a REQUIREMENT that filling equipment
which is designed to be cleaned in-place and which is used for filling other food products be
thoroughly cleansed and sanitised in-place in accordance with the manufacturer's
specifications and in compliance with GMP and the supplementary procedures that follow in
paragraph (d) to (f), of this Section.
20. Immediately following completion of filling operations for any other food product other
than water, it is REQUIRED that the filler be thoroughly rinsed internally and externally with
potable water (NB. Chlorinated water, at 1-3 ppm, is NOT potable).
21. It is a REQUIREMENT that in accordance with filler manufacturer's instructions, any parts
that are not designed to be cleaned in-place be disassembled and removed.
22. All of these parts MUST be cleaned and sanitised prior to reassembly using appropriate
cleaning and sanitizing procedures, as specified below.
23. Sanitising operations, including those performed by chemical means or by any other means
such as circulation of live steam or hot water, MUST be adequate to effect sanitisation of the
intended product water-contact surfaces and any other critical area.
24. It is recommended that the plant maintain a record of the intensity of the sanitising agent
and the time duration that the agent was in contact with the surface being sanitized.
25. It is REQUIRED that the following times and intensities be considered a minimum.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 62.
(i) Steam in enclosed system:
At least 76.6° C for at least 15 minutes or at least 93.3° C for at least 5 minutes
(ii) Hot water in enclosed system:
At least 76.6° C for at least 15 minutes or at least 93.3° C for at least 5 minutes
(iii) Chemical sanitizers are REQUIRED to be equivalent in bacterial action to a minute
exposure of 50 parts per million of available chlorine at 13.9° C when used as an
immersion or circulation solution.
26. Chemical sanitizers applied as a spray or fog MUST have as minimum 100 parts per million
of available chlorine at 13.9° C or its equivalent in bactericidal action.
27. It is REQUIRED that all surfaces of the filler that do not contact food products be cleaned
manually so as to render all surfaces clean and free of any residues.
28. It is a REQUIREMENT that the filler be prepared and all appropriate connections made in
accordance with the filler manufacturer's instructions to place the filler in the clean-in-place
mode.
29. If using an alkaline cleaning solution, the appropriate strength MUST be re-circulated
through the filler to provide effective cleaning of all product contact surfaces, with a minimum
re-circulation time of 20 minutes at a temperature between 60 and 75 degrees Centigrade.
30. The cleaning solution MUST be drained and followed with a potable water rinse-to-drain;
or otherwise removed from the system; for the removal of all residual cleaner alkalinity.
31. Following reassembly of all parts to place the filler into the product mode and just prior to
bottling water, the filler MUST be sanitised in-place in accordance with procedures (g) (vi) of
this Section.
32. Alternate cleaning, rinsing, or sanitising operations or processes not described in this
Section MUST be consistent with Australian or New Zealand regulatory requirements.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 63.
33. Bottled water that originates from a source that is not protected from surface
contamination MUST be subjected to ozonation, filtration rated at one micron, or another
effective process which removes or destroys the cysts of the parasite Giardia Lamblia and
Cryptosporidium.
34. Daily in-house total coliform monitoring on finished product MUST be done on each
product type.
35. It is recommended that quarterly rinse/swab tests be performed in-house or by a
laboratory using an approved methodology, on containers (incoming as well as those
immediately from the washer) and closures.
36. Each bottled water plant is REQUIRED to develop and maintain procedures for the
notification of the Government Authorities, consumer notification, and product recall, and the
water plant manager MUST implement any said procedure as necessary with respect to any
product for which the operator or the Government Authorities knows or has reason to believe
circumstances exist that may adversely affect its safety for the consumer.
37. In order to facilitate product identification or recall, each bottled water product MUST
contain a code that is designed to remain affixed to the container during use and which
contains either the date of manufacture, or a lot or batch number.
38. A bottled water supplier who knows that the Standard of Analytical Compliance has been
exceeded or has reason to believe that circumstances exist which may adversely affect the
safety of bottled water, including but not limited to source contamination, spills, accidents,
natural disasters, or breakdowns in treatment, MUST notify the Government authorities
promptly.
39. Where it is determined, based upon representative samples, risk analysis, information
provided by the bottled water supplier, and other information available that the circumstances
present an imminent hazard to the public health and that a form of consumer notice or product
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 64.
recall can effectively avoid or significantly minimise the threat to public health, the bottler
MUST initiate a product recall.
40. It is a REQUIREMENT that where applicable, ABWI members do NOT operate a bottled
water plant or bottle water for the purpose of sale or distribution without passing the ABWI
Plant Inspection Program within 12 months of joining ABWI.
41. A bottled water plant MUST not be operated except under the supervision of a competent
person qualified by experience, education, and training to operate and maintain the plant's
facilities.
42. Said person MUST hold a certificate demonstrating that he or she has successfully
completed the ABWI Certified Plant Operator course.
12.5 Plant Construction and Design
1. The grounds about a food plant under the control of the operator are REQUIRED to be kept
in a condition that will protect against the contamination of food.
2. If the plant grounds are bordered by grounds not under the operator's control and not
maintained in the manner described in paragraph (a) (i) through (iii) of this Section, care is
REQUIRED to be exercised in the plant by inspection, extermination, or other means to
exclude, dirt and filth that may be a source of food contamination.
3. Plant buildings and structures are REQUIRED to be suitable in size, construction and design
to facilitate maintenance and sanitary operations for food-manufacturing purposes.
4. The plant and facilities are REQUIRED to be:
(i) Provide sufficient space for such placement of equipment and storage of materials as is
necessary for the maintenance of sanitary operations and the production of safe food.
(ii) Permit the taking of proper precautions to reduce the potential for contamination of food,
food-contact surface, or food-packaging materials with microorganisms, chemicals, filth or
other extraneous material. The potential for contamination may be reduced by adequate food
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 65.
safety controls and operating practices or effective design, including the separation of
operations in which contamination is likely to occur, by one or more of the following means:
location, time, partition, air flow, enclosed systems or other effective means.
(iii) Permit the taking of proper precautions to protect food in outdoor bulk storage vessels by
any effective means, including:
a) Using protective coverings.
b) Controlling areas over and around the vessels to eliminate harborage for pests.
c) Checking on a regular basis for pests and pest infestation.
d) Be constructed in such a manner that floors, walls and ceilings may be adequately cleaned
and kept clean and kept in good repair; that drip or condensate from fixtures, ducts and pipes
does not contaminate food, food-contact surfaces, or food-packaging materials; and that
aisles or working spaces are provided between equipment and walls and are adequately
unobstructed and of adequate width to permit employees to perform their duties and to
protect against contaminating food or food-contact surfaces with clothing or personal contact.
(iv) Provide adequate lighting in hand-washing areas, dressing and locker rooms and toilet
rooms and in all areas where food is examined, processed or stored and where equipment or
utensils are cleaned; and provide safety-type light bulbs, fixtures, sky-lights or other glass
suspended over exposed food in any step of preparation or otherwise protect against food
contamination in case of glass breakage.
(v) Provide adequate ventilation or control equipment to minimise odours and vapours
(including steam and noxious fumes) in areas where they may contaminate food; and locate
and operate fans and other air-blowing equipment in a manner that minimise the potential for
contaminating food, food-packing materials, and food-contact surfaces.
(vi) Provide, where necessary, adequate screening or other protection again pests.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 66.
5. It is REQUIRED that buildings, fixtures and other physical facilities of the plant be
maintained in a sanitary condition
6. It is REQUIRED that they be kept in repair sufficient to prevent food from becoming
adulterated.
7. Cleaning and sanitizing of utensils and equipment MUST be conducted in a manner that
protects against contamination of food, food-contact surfaces or food-packaging materials.
8. Pests MUST NOT be allowed in any area of a food plant.
9. Effective measures are REQUIRED to be taken to exclude pests from the processing areas
and to protect against the contamination of food on the premises by pests.
10. It is recommended that the bottling room separated from other plant operations or
storage areas by tight walls, ceilings and self-closing doors to protect against contamination.
11. It is REQUIRED that conveyor openings NOT exceed the size required to permit passage of
containers.
12. If processing operations are conducted in other than a sealed system under pressure,
adequate protection is REQUIRED to be provided to preclude contamination of the water and
the system.
13. Adequate ventilation is REQUIRED to minimise condensation in processing rooms, bottling
rooms and in container washing and sanitising areas.
14. It is recommended that the washing and sanitising of containers for bottled water be
performed in an enclosed room.
15. It is REQUIRED that the washing and sanitising operations be positioned within the room
so as to minimise any possible post-sanitising contamination of the containers before they
enter the bottling room.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 67.
16. Rooms in which product water is handled, processed or held or in which containers, utensils
or equipment are washed or held MUST NOT open directly into any room used for domestic
household purposes.
17. It is REQUIRED that the product water supply for each plant be from an approved source
properly located, protected and is REQUIRED to be easily accessible, adequate and of a safe,
sanitary quality which MUST be in conformance at all times with the applicable laws and
regulations of the government agency or agencies having jurisdiction.
18. If different from the product water supply, the operations water supply MUST be obtained
from an approved source properly located, protected, and operated and MUST be easily
accessible, adequate, and of a safe, sanitary quality which MUST be in conformance at all
times with the applicable laws and regulations of the government agency or agencies having
jurisdiction.
12.6 Plant Hygiene
1. Cleaning compounds and sanitizing agents used in cleaning and sanitizing procedures MUST
be free from undesirable microorganisms
2. Cleaning compounds and sanitizing agents used in cleaning and sanitizing procedures MUST
be safe and adequate under the conditions of use.
3. Toxic cleaning compounds, sanitizing agents, and pesticide chemicals MUST be identified,
held and stored in a manner that protects against contamination of food, food-contact
surfaces or food-packaging materials.
4. It is recommended that all relevant regulations promulgated by other Federal State, and
local government agencies for the application, use or holding of these products be followed.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 68.
5. All food-contact surfaces including utensils and food-contact surfaces of equipment MUST
be cleaned as frequently as necessary to protect against contamination of food.
6. When the surfaces are wet-cleaned, it is a REQUIREMENT that, when necessary, they be
sanitized and thoroughly dried before subsequent use.
7. In wet processing, when cleaning is necessary to protect against the introduction of
microorganisms into food, it is REQUIRED that all food-contact surfaces be cleaned and
sanitized before use and after any interruption during which the food-contact surfaces may
have become contaminated.
8. Where equipment and utensils are used in a continuous production operation, the utensils
and food-contact surfaces of the equipment MUST be cleaned and sanitized as necessary.
9. It is recommended that non-food contact surfaces of equipment used in the operation of
food plants be cleaned as frequently as necessary to protect against contamination of food.
10. It is recommended that single-service articles (such as utensils intended for one-time use,
paper cups and paper towel(s) be stored in appropriate containers and it is REQUIRED that
they be handled, dispensed, used and disposed of in a manner that protects against
contamination of food or food-contact surfaces.
11. It is a REQUIREMENT that sanitising agents be adequate and safe under conditions of use.
12. Whenever air under pressure is directed at product water or a product water-contact
surface, it is a REQUIREMENT that it be free of oil, dust, rust, excessive moisture and
extraneous materials; it is REQUIRED that it NOT affect the bacteriological quality of the
water and it is recommended that it NOT adversely affect the flavour, colour or odour of the
water.
13. When employee locker and lunchrooms are provided, they are REQUIRED to be separate
from plant operations and storage areas and it is a REQUIREMENT that they be equipped with
self-closing doors.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 69.
14. It is a REQUIREMENT that the rooms be maintained in a clean and sanitary condition and it
is recommended that refuse containers be provided.
15. It is a REQUIREMENT that packaging or wrapping material or other processing supplies
NOT be stored in locker or lunchrooms.
16. The product water-contact surfaces of all multi-service containers, utensils, pipes and
equipment used in the transportation, processing, handling and storage of product water
MUST be clean and adequately sanitised.
17. All product water-contact surfaces MUST be inspected by plant personnel as often as
necessary to maintain the sanitary condition of such surfaces and to assure they are kept free
of scale, evidence of oxidation and other residue.
18. It is a REQUIREMENT that the presence of any unsanitary condition, scale, residue or
oxidation be immediately remedied by adequate cleaning and sanitising of that product water-
contact surface prior to use.
19. It is REQUIRED that after cleaning, all multi-service containers, utensils and disassembled
piping and equipment be transported and stored in such a manner as to assure drainage it is
REQUIRED that they be protected from contamination.
20. It is REQUIRED that single-service containers and caps are to be purchased and stored in
sanitary closures and kept clean therein in a clean, dry place until used.
21. Prior to use they ARE REQUIRED to be examined and as necessary, washed, rinsed and
sanitized and MUST be handled in a sanitary manner.
22. Filling, capping, closing, sealing and packaging of containers MUST be done in a sanitary
manner so as to preclude contamination of the bottled water.
12.7 Plant Design
2. Site is REQUIRED to be compliant with Food Standards Code sections 3.2.2 and 3.2.3.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 70.
3.Each plant is REQUIRED to be equipped with adequate sanitary facilities and
accommodations.
4. The water supply is REQUIRED to be sufficient for the operations intended and is
REQUIRED to be derived from an adequate source.
5. Any water that contacts food or food-contact surfaces MUST be safe and of adequate
sanitary quality.
6. It is a REQUIREMENT that running water at a suitable temperature, and under pressure as
needed, is to be provided in all areas where needed for the processing of food, for the cleaning
of equipment, utensils and food-packaging materials, or for employee sanitary facilities.
7. It is REQUIRED that plumbing be of adequate size and design and adequately installed and
maintained to:
(i) Carry sufficient quantities of water to required locations throughout the plant.
(ii) Properly convey sewage and liquid disposable waste from the plant.
(iii) Avoid constituting a source of contamination to food, water supplies, equipment or
utensils or creating an unsanitary condition.
(iv) Provide adequate floor drainage in all areas where floors are subject to flooding-type
cleaning or where normal operations release or discharge water or other liquid
waste on the floor.
(v) Provide that there is not backflow from, or cross-connection between, piping systems
that discharge waste water or sewage and piping systems that carry water for food
or food manufacturing.
8. Sewage disposal MUST be made into an adequate sewerage system or disposed of through
other adequate means.
9. Each plant is REQUIRED to provide its employees with adequate, readily accessible toilet
facilities.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 71.
10. Hand-washing facilities are REQUIRED to be adequate and convenient and be furnished
with running water at a suitable temperature.
11. It is a REQUIREMENT that rubbish be so conveyed, stored and disposed of as to minimise
the development of odour, minimise the potential for the waste becoming an attractant and
harborage or breeding place for pests, and protect against contamination of food, food-
contact surfaces, water supplies and ground surfaces.
12. It is REQUIRED that all plant equipment and utensils be suitable for their intended use.
13. All product water contact surfaces MUST be constructed of nontoxic and nonabsorbent
material which can be adequately cleaned and sanitized.
14. Instruments and controls used for measuring, regulating or recording temperatures, pH,
acidity, water activity, or other conditions that control or prevent the growth of undesirable
microorganisms in food are REQUIRED to be accurate and adequately maintained, and
adequate in number for their designated uses.
15. Storage tanks are REQUIRED to be of the type that can be closed to exclude all foreign
matter,
16. Storage tanks are REQUIRED to be adequately vented.
17. It is recommended that HEPA filtration be installed but care is essential to ensure sufficient
capacity of the filter to prevent tanks from being sucked in during discharge.
18. It is a REQUIREMENT that all treatment of product water by ozonation, distillation, ion-
exchanging, filtration, ultra-violet treatment, reverse osmosis, carbonation, mineral addition,
or any other process is done in a manner so as to be effective in accomplishing its intended
purpose.
19. All such processes MUST be performed in and by equipment and with substances that will
not adulterate the bottled product.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 72.
20. It is REQUIRED that a record of the type and date of physical inspections of such
equipment, conditions found and the performance and effectiveness of such equipment be
maintained by the plant.
21. Product water samples MUST be taken after processing and prior to bottling by the plant
and analysed as often as is necessary to assure uniformity and effectiveness of the processes
performed by the plant.
22. It is a REQUIREMENT that the methods of analysis be those approved by the government
agency or agencies having jurisdiction.
23. Multi-service primary containers MUST be adequately cleaned, sanitized and inspected just
prior to being filled, capped and sealed.
24. Containers found to be unsanitary or defective by the inspection MUST be reprocessed or
discarded.
25. All multi-service primary containers MUST be washed, rinsed and sanitised by mechanical
washers or by any other method giving adequate sanitary results.
26. Mechanical washers are REQUIRED to be inspected as often as is necessary to assure
adequate performance.
27. It is REQUIRED that records of physical maintenance, inspections and conditions found,
and performance of the mechanical washer be maintained by the plant.
28. Multi-service shipping cases MUST be maintained in such condition as to assure they will
not contaminate the primary container or the product water.
29. Adequate dry or wet cleaning procedures are REQUIRED to be performed as often as
necessary to maintain the cases in satisfactory condition.
30. It is REQUIRED that cleaning and sanitising solutions utilized by the plant be sampled and
tested by the plant as often as is necessary to assure adequate performance in the cleaning and
sanitizing operations.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 73.
31. It is REQUIRED that records of these tests be maintained by the plant.
32. During the process of filling, capping or sealing either single-service or multi-service
containers, it is a REQUIREMENT that the performance of the filler, capper or sealer be
monitored and the filled containers visually or electronically inspected to assure they are
sound, properly capped or sealed, and coded and labeled.
33. Containers that are not satisfactory MUST be reprocessed or rejected.
34. Bottlers MUST only use nontoxic containers and closures.
35. All containers and closures MUST be inspected to ascertain that they are free from
contamination.
36. At least once each 3 months, it is recommended that a bacteriological swab and/or rinse
count be made from at least four containers and closures selected just prior to filling and
sealing.
37. All samples MUST be free of coliform organisms.
38. The procedure and apparatus for these bacteriological tests are REQUIRED to be in
conformance with those recognized by the government agency or agencies having jurisdiction.
39. It is a REQUIREMENT that tests be performed either by trained plant personnel or by a
laboratory using approved methodologies.
40. It is a REQUIREMENT that all operations in the receiving, inspecting, transporting,
segregating, preparing, manufacturing, packaging and storing of food be conducted in
accordance with adequate sanitation principles.
41. It is a REQUIREMENT that overall sanitation of the plant be under the supervision of one or
more competent individuals assigned responsibility for this function.
42. It is a REQUIREMENT that all reasonable precautions be taken to ensure that production
procedures do not contribute contamination from any source.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 74.
43. It is a REQUIREMENT that chemical, microbial, or extraneous-material testing procedures
be used where necessary to identify sanitation failures or possible food contamination.
44. All food that has become contaminated to the extent that it is adulterated MUST be
rejected, or if permissible, treated or processed to eliminate the contamination.
45. It is a REQUIREMENT that raw materials and other ingredients be inspected and
segregated or otherwise handled as necessary to ascertain that they are clean and suitable for
processing into food and it is a REQUIREMENT that they be stored under conditions that will
protect against contamination and minimize deterioration.
46. It is a REQUIREMENT that raw materials be washed or cleaned as necessary to remove soil
or other contamination.
47. Water used for washing, rinsing, or conveying food is REQUIRED to be of a safe and of
adequate sanitary quality.
48. Containers and carriers of raw materials should be inspected on receipt to ensure that their
condition has not contributed to the contamination or deterioration of food.
49. It is a REQUIREMENT that raw materials and other ingredients either not contain levels of
microorganisms that may produce food poisoning or other disease in humans OR it is
REQUIRED that they be adequately treated during manufacturing operations, by washing,
sanitising and rinsing according to the instructions of the manufacturers of the chemicals used,
so that they no longer contain levels that would cause the product to be adulterated.
50. Raw materials, other ingredients, and rework susceptible to contamination with pests,
undesirable microorganisms, or extraneous material MUST comply with applicable FSANZ
Food Code Regulations, guidelines and defect action levels for natural or unavoidable defects if
a manufacturer wishes to use the materials in manufacturing food.
51. It is a REQUIREMENT that raw materials, other ingredients, and rework be held in bulk, or
in containers designed and constructed so as to protect against contamination and it is a
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 75.
REQUIREMENT that they be held at such temperature and relative humidity and in such a
manner as to prevent the food from becoming adulterated
52. Material scheduled for rework MUST be identified as such.
53. Measures such as sterilizing, irradiating, pasteurising, freezing, refrigerating, controlling pH
or controlling Aw that are taken to destroy or prevent the growth of undesirable
microorganisms, particularly those of public health significance, MUST be adequate under the
conditions of manufacture, handling, and distribution to prevent food from being adulterated.
54. Work-in-process MUST be handled in a manner that protects against contamination.
55. It is a REQUIREMENT that effective measures be taken to protect finished food from
contamination by raw materials, other ingredients, or refuse.
56. When raw materials, other ingredients, or refuse are unprotected, they MUST NOT be
handled simultaneously in a receiving, loading or shipping area if that handling could result in
contamination.
57. It is a REQUIREMENT that food transported by conveyor be protected against
contamination as necessary.
58. It is a REQUIREMENT that equipment, containers and utensils used to convey, hold or
store raw materials, work-in-process, rework or food be constructed, handled and maintained
during manufacturing or storage in a manner that protects against contamination.
59. It is a REQUIREMENT that effective measures be taken to protect against the inclusion of
metal or other extraneous material in food.
60. Food, raw materials, and other ingredients that are adulterated are REQUIRED to be
disposed of in a manner that protects against the contamination of other food.
61. If the adulterated food is capable of being reconditioned, it is a REQUIRED to be
reconditioned using a method that has been proven to be effective OR it is a REQUIREMENT
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 76.
that it be re-examined and found not to be adulterated before being incorporated into other
food.
62. It is a REQUIREMENT that mechanical manufacturing steps such as washing and filling be
performed so as to protect food against contamination.
63. Filling, assembling, packaging and other operations MUST be performed in such a way that
the food is protected against contamination.
64. It is a REQUIREMENT that storage and transportation of finished food be under conditions
that will protect food against physical, chemical and microbial contamination as well as against
deterioration of the food and the container.
12.8 Cooler Cleaning
Bottled water manufacturers who clean and/or refurbish coolers for re-sale or re-hire MUST
have a cleaning and sanitising procedure in place.
It is REQUIRED that this procedure includes the following:-
a) isolate returned coolers from new or sanitised coolers
b) clean and sanitise away from process areas where there can be no contamination of raw
materials, process lines or finished product
c) check, clean and sanitise the coolers
d) repair as required
e) when completed the coolers will be bagged or boxed in a manner that will minimise the risk
of recontamination
f) store in an appropriate manner
12.9 Record Keeping
It is a REQUIREMENT that all records be retained at the plant for not less than 7 years.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 77.
12.10 Laboratory Maintenance
In-house laboratories are REQUIRED to be maintained in a clean and appropriate manner for
the activities to be conducted without causing contamination by handling or an unsuitable
environment.
Laboratory maintenance REQUIRED includes:-
1. The construction, space, lighting and ventilation to be designed to conduct the required
activities.
2. All laboratory equipment is adequately sanitised and maintained in proper working order.
3. Appropriate sanitisation of the laboratory will be maintained.
4. Quality control monitoring will be conducted to ensure the reliability and efficacy of tests,
test results and laboratory personnel.
5. Access will be restricted to authorised personnel.
6. Staff may only enter wearing clean outer clothing.
7. Rubbish will be kept covered and removed daily.
8. Procedures are documented and document control established for all laboratory operations
and records.
All contaminated materials are REQUIRED to be sterilised prior to disposal.
12.11 Labeling Requirements
1. Bottled water product labeling MUST comply with all applicable provisions under FSANZ
Food Standards Code and Appendices. The Joint Australia New Zealand Food Standards Code
(FSC) is administered by FSANZ and sets down mandatory labelling requirements.
2. Bottled water product labelling MUST comply with the provisions of the FSANZ Code of
Practice on Nutrient Claims in Food Labels and in Advertisements.
Australasian Bottled Water Institute Model Code for Production of Bottled Water; May 2013 P 78.
3. Bottled Water product labelling MUST also be in accordance with the Australian Consumer
Law.
4. Bottled water product labelling MUST also comply with applicable provisions set out in
National Trade Measures Regulations 2009 administered by the National Measurement
Institute (NMI).
5. Bottled water product labelling MUST also comply with applicable provisions set out in the
Australian National Standard for Organic & Biodynamic Products (DR08147).
6. Bottled water product labeling, where manufactured outside of Australia and New Zealand
MUST comply with local legislative provisions in addition to requirements in Australia and New
Zealand. Where water is neither bottled nor sold in Australia and/or New Zealand, the
requirements of equivalent local regulation applies.
END
top related