owner’s manual - yamaha xjr cz | czech xjr owner's site · protective clothing is as...

5EA-28199-E4

XJR1300

OWNER’S MANUAL

PRINTED ON RECYCLED PAPER

YAMAHA MOTOR CO., LTD.

PRINTED IN JAPAN2001 . 8 - 0.3 × 1 CR

E_5GK_Consumer.fm Page 11 Wednesday, June 13, 2001 1:03 PM

03338 INTRODUCTION

Yamaha’s vast experience andcture of high-quality products,

bility.

o as to enjoy all advantages ofnstruct you in how to operate, to safeguard yourself and oth-

lp keep your motorcycle in theions, do not hesitate to contact

nt rides. So, remember to put

E_5ea.book Page 1 Tuesday, October 2, 2001 3:54 PM

Welcome to the Yamaha world of motorcycling!

As the owner of an XJR1300, you are benefiting fromnewest technology regarding the design and manufawhich have earned Yamaha a reputation for dependa

Please take the time to read this manual thoroughly, syour XJR1300. The owner’s manual does not only iinspect and maintain your motorcycle, but also in howers from trouble and injury.

In addition, the many tips given in this manual will hebest possible condition. If you have any further questyour Yamaha dealer.

The Yamaha team wishes you many safe and pleasasafety first!

EAU00005PORTANT MANUAL INFORMATION

ticularly important information is distinguished in this manual by the following notations:

ERT! YOUR SAFETY IS

re injury or death to theting or repairing the

to avoid damage to the

learer.

torcycle and should remain

d quality. Therefore, whilelable at the time of printing,d this manual. If you haveaha dealer.

The Safety Alert Symbol meINVOLVED!

WARNING Failure to follow WARNING inmotorcycle operator, a bymotorcycle.

AUTION: A CAUTION indicates specialmotorcycle.

OTE: A NOTE provides key informati

NOTE:_

� This manual should be considwith it even if the motorcycle

� Yamaha continually seeks adthis manual contains the mosthere may be minor discrepaany questions concerning this

ans ATTENTION! BECOME AL

structions could result in sevestander, or a person inspec

precautions that must be taken

on to make procedures easier or c

ered a permanent part of this mois subsequently sold.vancements in product design ant current product information avaincies between your motorcycle an manual, please consult your Yam

IMPORTANT MANUAL INFORMATIONEW000002

IS MANUAL CAREFULLY AND COMPLETELY BEFORE OPERATINGE.

WARNING_

PLEASE READ THTHIS MOTORCYCL_

IMPORTANT MANUAL INFORMATION

Anywit

EAU04229

XJR1300OWNER’S MANUAL

01 by Yamaha Motor Co., Ltd.1st edition, July 2001All rights reserved.

reprinting or unauthorized usehout the written permission of

Yamaha Motor Co., Ltd.is expressly prohibited.

Printed in Japan.

LE OF CONTENTS

FUNCTIONS 3

T RIDING POINTS 5

D MINOR REPAIR 6

ORAGE 7

EAU00009

E_5ea.book P

1 GIVE SAFETY THE RIGHT OF

2 DESCRIPTION

3 INSTRUMENT AND CONTROL

4 PRE-OPERATION CHECKS

5 OPERATION AND IMPORTAN

6 PERIODIC MAINTENANCE AN

7 MOTORCYCLE CARE AND ST

8 SPECIFICATIONS

9 CONSUMER INFORMATION

age 1 Tuesday, October 2, 2001 3:54 PM

GIVE SAFETY THE RIGHT OF WAY

GIVE SAFETY THE RIGHT OF WAY ................................................ 1-1

EAU00021

nsurpassed feeling of power andt accept; even the best motorcycle

e and operating condition of youre for the rider: good performanceedication, drugs and alcohol is, ofrs—must always be at their mentallcohol, there is a tendency to take

eat belts are for car drivers and made of leather or tear-resistantves and a properly fitting helmet.

elessness. Although full-coverage and protection, motorcyclists willrisk of going too fast and are apt tohe good motorcyclist rides safely, caused by others.

1-GIVE SAFETY THE RIGHT OF WAY

Motorcycles are fascinating vehicles, which can give you an ufreedom. However, they also impose certain limits, which you musdoes not ignore the laws of physics.

Regular care and maintenance are essential for preserving valumotorcycle. Moreover, what is true for the motorcycle is also trudepends on being in good shape. Riding under the influence of mcourse, out of the question. Motorcycle riders—more than car driveand physical best. Under the influence of even small amounts of adangerous risks.

Protective clothing is as essential for the motorcycle rider as spassengers. Always wear a complete motorcycle suit (whethersynthetic materials with protectors), sturdy boots, motorcycle gloOptimum protective wear, however, should not encourage carhelmets and suits, in particular, create an illusion of total safetyalways be vulnerable. Riders who lack critical self-control run the take chances. This is even more dangerous in wet weather. Tpredictably and defensively—avoiding all dangers, including those

Enjoy your ride!

DESCRIPTION

Left view ............................................................................................. 2-1Right view........................................................................................... 2-2Controls and instruments ................................................................... 2-3

EAU00026

1.2.3.4.5.6.7.8.9.

SCRIPTION

ft view

Clutch fluid reservoir (page 6-20)Fuel cock (page 3-10)Shock absorber assembly spring preload adjusting rings (page 3-15)Luggage strap holders (page 3-16)Helmet holder/seat lock (page 3-12/page 3-11)Throttle stop screw (page 6-13)Shift pedal (page 3-6)Engine oil filler element (page 6-8)Engine oil drain bolt (page 6-8)

DESCRIPTION

101112

131415

(page 6-11)(page 3-8)

ervoir (page 6-19)eload adjusting bolt (page 3-14)

(page 6-29)(page 6-8)

ck window (page 6-8)(page 3-7)

ight view

. Tail/brake light (page 6-31)

. Luggage strap holders (page 3-16)

. Shock absorber assembly spring preload adjusting rings (page 3-15)

. Owner’s tool kit (page 6-1)

. Rear brake fluid reservoir (page 6-19)

. Fuses (page 6-29)

16. Air filter element17. Fuel tank18. Front brake fluid res19. Front fork spring pr20. Headlight21. Engine oil filler cap22. Engine oil level che23. Brake pedal

1.2.3.4.5.6.

ches (page 3-5)(page 3-7)(page 6-13)

lock (page 3-1)

SCRIPTION

ntrols and instruments

Clutch lever (page 3-5)Left handlebar switches (page 3-4)Starter (choke) lever (page 3-11)Speedometer unit (page 3-3)Fuel gauge (page 3-3)Tachometer (page 3-3)

7. Right handlebar swit8. Brake lever9. Throttle grip

10. Main switch/steering

INSTRUMENT AND CONTROL FUNCTIONS

Main switch/steering lock .....................................3-1Indicator and warning lights .................................3-2Speedometer unit ................................................3-3Tachometer ..........................................................3-3Fuel gauge ...........................................................3-3Anti-theft alarm (optional) ....................................3-4Handlebar switches .............................................3-4Clutch lever ..........................................................3-5Shift pedal ............................................................3-6Brake lever ...........................................................3-7Brake pedal ..........................................................3-7Fuel tank cap .......................................................3-8Fuel ......................................................................3-9

Fuel tank breather hose .................................... 3-10Fuel cock ........................................................... 3-10Starter (choke) lever .......................................... 3-11Seat ................................................................... 3-11Helmet holder .................................................... 3-12Storage compartment ....................................... 3-13Adjusting the front fork ...................................... 3-13Adjusting the shock absorber assemblies ......... 3-15Luggage strap holders ...................................... 3-16Sidestand .......................................................... 3-17Ignition circuit cut-off system ............................. 3-17

EAU00027

EW000016

WARNINGer turn the key to “OFF” orCK” while the motorcycle is

ving, otherwise the electricaltems will be switched off, whichy result in loss of control or anident. Make sure that the motor-le is stopped before turning the to “OFF” or “LOCK”.

ush.urn.

MaThethe usepos

ONAll powThe

OFAll can

STRUMENT AND CONTROL FUNCTIONS

EAU00029

in switch/steering lock main switch/steering lock controlsignition and lighting systems, and isd to lock the steering. The variousitions are described below.

EAU00036

electrical systems are supplied wither, and the engine can be started. key cannot be removed.

EAU00038

Felectrical systems are off. The key be removed.

EAU00041

LOCKThe steering is locked, and all electricalsystems are off. The key can be re-moved.

To lock the steering1. Turn the handlebars all the way to

the left or right.2. Push the key in from the “OFF” po-

sition, and then turn it to “LOCK”while still pushing it.

3. Remove the key.

To unlock the steeringPush the key into the main switch, andthen turn it to “OFF” while still pushingit.

Nev“LOmosysmaacccyckey_

1. P2. T

NTROL FUNCTIONS

ThauligelbeThke

EAU00061

utral indicator light “ ” is indicator light comes on when thensmission is in the neutral position.

EAU03201

l level warning light “ ” is warning light comes on when thegine oil level is low.e electrical circuit of the warning lightn be checked according to the fol-ing procedure.

. Set the engine stop switch to “ ”and turn the key to “ON”.

. Shift the transmission into the neu-tral position or pull the clutch lever.

. Push the start switch. If the warn-ing light does not come on whilepushing the start switch, have aYamaha dealer check the electri-cal circuit.

TE:en if the oil level is sufficient, therning light may flicker when riding onlope or during sudden accelerationdeceleration, but this is not a mal-ction.

INSTRUMENT AND CO

EAU04356

(Parking)e steering is locked, the taillight andxiliary light are on, and the hazardht can be turned on, but all otherectrical systems are off. The key can removed.e steering must be locked before they can be turned to “ ”.

ECA00043

AUTION:o not use the parking position for extended length of time, other-

ise the battery may discharge. EAU03034

Indicator and warning lights

EAU04121

Turn signal indicator lights “ ”and “ ” The corresponding indicator light flash-es when the turn signal switch ispushed to the left or right.

EAU00063

High beam indicator light “ ” This indicator light comes on when thehigh beam of the headlight is switchedon.

NeThtra

OiThenThcalow

Evwaa sor fun_

1. Left turn signal indicator light “ ”2. High beam indicator light “ ”3. Neutral indicator light “ ”4. Right turn signal indicator light “ ”5. Oil level warning light “ ”

SpThea stripriditotashowaThewittantanyou

EAU00110

el gauge fuel gauge indicates the amount of

l in the fuel tank. The needle movesards “E” (Empty) as the fuel levelreases. When the needle reaches

, approximately 4.5 L of fuel remainhe fuel tank. If this occurs, refuel asn as possible.

TE:not allow the fuel tank to empty it- completely.

1. T2. T3. O4. S

uel gauge

EAU00097

eedometer unit speedometer unit is equipped withpeedometer, an odometer and ameter. The speedometer showsng speed. The odometer shows thel distance traveled. The tripmeterws the distance traveled since it

s last set to zero with the reset knob. tripmeter can be used together

h the fuel gauge to estimate the dis-ce that can be traveled with a fullk of fuel. This information will enable to plan future fuel stops.

EAU00101

Tachometer The electric tachometer allows the riderto monitor the engine speed and keep itwithin the ideal power range.

EC000003

CAUTION:_

Do not operate the engine in the ta-chometer red zone.Red zone: 9,500 r/min and above _

FuThefuetowdec“E”in tsoo

Do self_

ripmeter reset knobripmeterdometerpeedometer

1. Tachometer2. Tachometer red zone

NTROL FUNCTIONS

AThanYade

EAU03826

ard switch “ ” the key in the “ON” or “ ” posi-

, use this switch to turn on the haz-light (simultaneous flashing of all signal lights). hazard light is used in case of anrgency or to warn other driversn your motorcycle is stoppedre it might be a traffic hazard.

EC000006

UTION:not use the hazard light for an ex-ded length of time, otherwise thetery may discharge.

EAU03889

n signal switch “ / ” signal a right-hand turn, push thisch to “ ”. To signal a left-hand, push this switch to “ ”. Whenased, the switch returns to the cen-position. To cancel the turn signalts, push the switch in after it has re-ed to the center position.

EAU00129

n switch “ ” ss this switch to sound the horn.

INSTRUMENT AND CO

EAU00109

nti-theft alarm (optional) is motorcycle can be equipped with optional anti-theft alarm by amaha dealer. Contact a Yamahaaler for more information.

EAU00118

Handlebar switches

EAU00120

Pass switch “PASS” Press this switch to flash the headlight.

EAU03888

Dimmer switch “ / ” Set this switch to “ ” for the highbeam and to “ ” for the low beam.

HazWithtionard turnTheemewhewhe

Do tenbat_

TurTo switturnreleter lighturn

HorPre

1. Pass switch “PASS”2. Dimmer switch “ / ”3. Hazard switch “ ”4. Turn signal switch “ / ”5. Horn switch “ ”

EnSethestocy,turnstu

LigSeauxlighthe“

EAU00153

tch lever clutch lever is located at the leftdlebar grip. To disengage thech, pull the lever toward the handle- grip. To engage the clutch, release lever. The lever should be pulledidly and released slowly for smoothch operation.

1. E2. L3. S

lutch lever

EAU03890

gine stop switch “ / ” t this switch to “ ” before starting engine. Set this switch to “ ” top the engine in case of an emergen- such as when the motorcycle over-s or when the throttle cable is

EAU03898

ht switch “ / / ” t this switch to “ ” to turn on theiliary light, meter lighting and tail-t. Set the switch to “ ” to turn on headlight also. Set the switch to” to turn off all the lights.

EAU00143

Start switch “ ” Push this switch to crank the enginewith the starter.

EC000005

CAUTION:_

See page 5-1 for starting instruc-tions prior to starting the engine. _

CluThehanclutbartherapclut

ngine stop switch “ / ”ight switch “ / / ”tart switch “ ”

NTROL FUNCTIONS

ThcladleadpuMonarThclcifocu

INSTRUMENT AND CO

e clutch lever is equipped with autch lever position adjusting dial. Tojust the distance between the clutch

ver and the handlebar grip, turn thejusting dial while holding the levershed away from the handlebar grip.ake sure that the appropriate setting the adjusting dial is aligned with therow mark on the clutch lever.e clutch lever is equipped with a

utch switch, which is part of the ignitionrcuit cut-off system. (See page 3-17r an explanation of the ignition circuitt-off system.)

EAU00157

Shift pedal The shift pedal is located on the leftside of the engine and is used in com-bination with the clutch lever whenshifting the gears of the 5-speed con-stant-mesh transmission equipped onthis motorcycle.

Clutch lever position adjusting dialArrow mark

1. Shift pedal

BrThehanbrabar

EAU00162

ake pedal brake pedal is on the right side of

motorcycle. To apply the rearke, press down on the brake pedal.

1. B rake pedal

EAU00161

ake lever brake lever is located at the rightdlebar grip. To apply the frontke, pull the lever toward the handle- grip.

The brake lever is equipped with a po-sition adjusting dial. To adjust the dis-tance between the brake lever and thehandlebar grip, turn the adjusting dialwhile holding the lever pushed awayfrom the handlebar grip. Make sure thatthe appropriate setting on the adjustingdial is aligned with the arrow mark onthe brake lever.

BrThethebra

rake lever 1. Arrow mark2. Brake lever position adjusting dial

NTROL FUNCTIONS

ToOseit leop

INSTRUMENT AND CO

EAU02935

uel tank cap

open the fuel tank cappen the fuel tank cap lock cover, in-rt the key into the lock, and then turn

1/4 turn clockwise. The lock will be re-ased and the fuel tank cap can beened.

close the fuel tank cap. Push the fuel tank cap into posi-

tion with the key inserted in thelock.

2. Turn the key counterclockwise tothe original position, remove it,and then close the lock cover.

NOTE:_

The fuel tank cap cannot be closed un-less the key is in the lock. In addition,the key cannot be removed if the cap isnot properly closed and locked. _

EWA00025

WARNING_

Make sure that the fuel tank cap isproperly closed before riding. _

Fuel tank cap lock coverUnlock.

FuMatheof t

r Yamaha engine has been de-ed to use regular unleaded gaso-

with a research octane number ofor higher. If knocking (or pinging)urs, use a gasoline of a differentnd or premium unleaded fuel. Usenleaded fuel will extend spark plugand reduce maintenance costs.

1. F2. F

EAU03753

el ke sure that there is sufficient fuel in tank. Fill the fuel tank to the bottomhe filler tube as shown.

EW000130

WARNINGDo not overfill the fuel tank, oth-erwise it may overflow when thefuel warms up and expands. Avoid spilling fuel on the hotengine.

EAU00185

CAUTION:_

Immediately wipe off spilled fuelwith a clean, dry, soft cloth, sincefuel may deteriorate painted surfac-es or plastic parts. _

EAU04284

ECA00104

CAUTION:_

Use only unleaded gasoline. Theuse of leaded gasoline will cause se-vere damage to internal engineparts, such as the valves and pistonrings, as well as to the exhaust sys-tem. _

Yousignline91 occbraof ulife

uel tank filler tubeuel level

Recommended fuel:REGULAR UNLEADED GASOLINE ONLY

Fuel tank capacity:Total amount:

21 LReserve amount:

NTROL FUNCTIONS

Sis indicates reserve. With the fuelck lever in this position, the fuel re-rve is made available. Quickly turne fuel cock lever to this position if youn out of fuel while riding, otherwisee engine may stall and will have to beimed (see “PRI”). After turning theel cock lever to “RES”, refuel as soon possible and be sure to turn the fuelck lever back to “ON”!

Arrow mark positioned over “RES”

ES: Reserve position

INSTRUMENT AND CO

EAU02955

uel tank breather hose fore operating the motorcycle:

� Check the fuel tank breather hoseconnection.

� Check the fuel tank breather hosefor cracks or damage, and replaceit if damaged.

� Make sure that the end of the fueltank breather hose is not blocked,and clean it if necessary.

EAU00207

Fuel cock The fuel cock supplies fuel from thetank to the carburetors while also filter-ing it.The fuel cock lever positions are ex-plained as follows and shown in the il-lustrations.

ONWith the fuel cock lever in this position,fuel flows to the carburetors when theengine is running. Turn the fuel cock le-ver to this position when starting theengine and riding.

REThcosethruthprfuasco

Fuel tank breather hoseOriginal position (white mark)

1. Arrow mark positioned over “ON”

ON: Normal position

PRThilev“prthisallofuewillginverrefu

EAU04406

remove the seatInsert the key into the seat lock,and then turn it as shown.Pull the seat off.

nlock.

Is indicates prime. With the fuel cocker in this position, the engine can beimed”. Turn the fuel cock lever to position when the engine has beenwed to run out of fuel. This sendsl directly to the carburetors, which make starting easier. After the en-e has started, be sure to turn the le- to “ON” (or “RES” if you have noteled yet).

EAU03839

Starter (choke) lever “ ” Starting a cold engine requires a richerair-fuel mixture, which is supplied bythe starter (choke).Move the lever in direction a to turn onthe starter (choke).Move the lever in direction b to turn offthe starter (choke).

rrow mark positioned over “PRI”

I: Priming position

1. Starter (choke) lever “ ” 1. U

NTROL FUNCTIONS

INSTRUMENT AND CO

install the seat. Insert the projection on the front of

the seat into the seat holder asshown.

. Push the rear of the seat down tolock it in place.

. Remove the key.

OTE:ake sure that the seat is properly se-red before riding.

EAU04291

Helmet holder To open the helmet holder, insert thekey into the seat lock, and then turn thekey as shown.To lock the helmet holder, turn the keyto the original position, and then re-move it.

EW000030

WARNING_

Never ride with a helmet attached tothe helmet holder, since the helmetmay hit objects, causing loss ofcontrol and possibly an accident. _

ProjectionSeat holder

1. Unlock.

StThto U-LWhagewitnotsurlos

EAU00285

justing the front fork front fork is equipped with springoad adjusting bolts.

EW000035

WARNINGays adjust both fork legs equal-therwise poor handling and losstability may result.

1. U2. S3. L

EAU04292

orage compartment is storage compartment is designedhold an optional genuine YamahaOCK. (Other locks may not fit.)en placing a U-LOCK in the stor- compartment, securely fasten it

h the straps. When the U-LOCK is in the storage compartment, bee to secure the straps to preventing them.

When storing the owner’s manual orother documents in the storage com-partment, be sure to wrap them in aplastic bag so that they will not getwet. When washing the motorcycle,be careful not to let any water enterthe storage compartment.

AdThisprel

Alwly, oof s_-LOCK bar

trap (× 2)ock of the U-LOCK

NTROL FUNCTIONS

AdToththrelosuea

INSTRUMENT AND CO

just the spring preload as follows. increase the spring preload and

ereby harden the suspension, turne adjusting bolt on each fork leg in di-ction a. To decrease the spring pre-ad and thereby soften thespension, turn the adjusting bolt onch fork leg in direction b.

NOTE:_

Align the appropriate groove on the ad-justing mechanism with the top of thefront fork cap bolt. _

CI-10E

Spring preload adjusting bolt 1. Current setting2. Front fork cap bolt

Setting

Minimum (soft) 7

Standard 5

Maximum (hard) 1

AdasEaequing

Nemeor _

Alwasshanres_

decrease the spring preload andreby soften the suspension, hold theer ring in place while turning theer ring (adjusting ring) on eachck absorber assembly as shown intration ,.

pper ringower ring (spring preload adjusting ring)

EAU04407

justing the shock absorber semblies ch shock absorber assembly isipped with a spring preload adjust-

ring.EC000015

UTION:ver attempt to turn an adjustingchanism beyond the maximumminimum settings.

EW000040

WARNINGays adjust both shock absorberemblies equally, otherwise poordling and loss of stability mayult.

Adjust the spring preload as follows,using the special wrenches includedalong with the owner’s tool kit.To increase the spring preload andthereby harden the suspension, holdthe upper ring in place while turning thelower ring (adjusting ring) on eachshock absorber assembly as shown inillustration +.

To theupplowshoillus

1. Upper ring2. Lower ring (spring preload adjusting ring)

1. U2. L

NTROL FUNCTIONS

EAU04276

ggage strap holders ere are four luggage strap holders,o of which can be turned out for eas- access.

Luggage strap holder (× 4)

INSTRUMENT AND CO

EAU00316

WARNING_

These shock absorbers containhighly pressurized nitrogen gas. Forproper handling read and under-stand the following information be-fore handling the shock absorbers.The manufacturer cannot be held re-sponsible for property damage orpersonal injury that may result fromimproper handling.

� Do not tamper with or attempt toopen the gas cylinders.

� Do not subject the shock ab-sorbers to an open flame or oth-er high heat sources, otherwisethey may explode due to exces-sive gas pressure.

� Do not deform or damage thegas cylinders in any way, as thiswill result in poor damping per-formance.

� Always have a Yamaha dealerservice the shock absorbers.

LuThtwier

SidTheof lowmo

Thethecut(Sethe_

EAU03741

ition circuit cut-off system ignition circuit cut-off system (com-ing the sidestand switch, clutchtch and neutral switch) has the fol-ing functions.It prevents starting when the trans-mission is in gear and the side-stand is up, but the clutch lever isnot pulled.It prevents starting when the trans-mission is in gear and the clutchlever is pulled, but the sidestand isstill down.It cuts the running engine whenthe transmission is in gear and thesidestand is moved down.

iodically check the operation of theition circuit cut-off system accordinghe following procedure.

EAU00330

estand sidestand is located on the left side

the frame. Raise the sidestand orer it with your foot while holding thetorcycle upright.

TE: built-in sidestand switch is part of

ignition circuit cut-off system, whichs the ignition in certain situations.e further down for an explanation of ignition circuit cut-off system.)

EW000044

WARNING_

The motorcycle must not be riddenwith the sidestand down, or if thesidestand cannot be properlymoved up (or does not stay up), oth-erwise the sidestand could contactthe ground and distract the opera-tor, resulting in a possible loss ofcontrol. Yamaha’s ignition circuitcut-off system has been designed toassist the operator in fulfilling theresponsibility of raising the side-stand before starting off. Therefore,check this system regularly as de-scribed below and have a Yamahadealer repair it if it does not functionproperly. _

IgnTheprisswilow

Perignto t

NTROL FUNCTIONS

INSTRUMENT AND CO

EW000046

WARNING� The vehicle must be placed on

the centerstand during this in-spection.

� If a malfunction is noted, have aYamaha dealer check the sys-tem before riding.

CD-01E

itch may be defective.le should not be ridden until

Yamaha dealer.

switch may be defective.le should not be ridden until

Yamaha dealer.

itch may be defective.le should not be ridden until

Yamaha dealer.

ost reliable if performed withengine.

With the engine turned off:1. Move the sidestand down.2. Make sure that the engine stop switch is set to “ ”.3. Turn the key to “ON”. 4. Shift the transmission into the neutral position.5. Push the start switch.Does the engine start?

The neutral swThe motorcycchecked by a

With the engine still running:6. Move the sidestand up.7. Keep the clutch lever pulled.8. Shift the transmission into gear.9. Move the sidestand down.Does the engine stall?

After the engine has stalled:10. Move the sidestand up.11. Keep the clutch lever pulled.12. Push the start switch.Does the engine start?

The sidestandThe motorcycchecked by a

The clutch swThe motorcycchecked by a

NOTE:This check is ma warmed-up

YES NO

The system is OK. The motorcycle can be ridden.

YES NO

PRE-OPERATION CHECKS

Pre-operation check list ..................................................................... 4-1

EAU01114

teriorate quickly and unexpectedly,). Any damage, fluid leakage or lossddition to a thorough visual inspec-

Theeveof ti

EAU03439

6-7–6-8

6-19–6-20

6-17–6-20

6-19–6-20

CO-01E

E-OPERATION CHECKS

condition of a vehicle is the owner’s responsibility. Vital components can start to den if the vehicle remains unused (for example, as a result of exposure to the elementsre air pressure could have serious consequences. Therefore, it is very important, in a, to check the following points before each ride.

Pre-operation check list ITEM CHECKS

el• Check fuel level in fuel tank.• Refuel if necessary.• Check fuel line for leakage.

gine oil• Check oil level in engine.• If necessary, add recommended oil to specified level.• Check vehicle for oil leakage.

nt brake

• Check operation.• If soft or spongy, have Yamaha dealer bleed hydraulic system.• Check fluid level in reservoir.• If necessary, add recommended brake fluid to specified level.• Check hydraulic system for leakage.

ar brake

• Check operation.• If soft or spongy, have Yamaha dealer bleed hydraulic system.• Check fluid level in reservoir.• If necessary, add recommended brake fluid to specified level.• Check hydraulic system for leakage.

• Check operation.• If soft or spongy, have Yamaha dealer bleed hydraulic system.• Check fluid level in reservoir.• If necessary, add recommended fluid to specified level.• Check hydraulic system for leakage.

rottle grip• Make sure that operation is smooth.• Check free play.• If necessary, have Yamaha dealer make adjustment or lubricate.

ntrol cables • Make sure that operation is smooth.• Lubricate if necessary.

PERATION CHECKS

Pr ection can be accomplished in a verysh_

EWA00033

If ted and repaired before operatingth_

D 6-21,6-23

W 6-14-6-17

B 6-24

C 6-25

Ina —

S 3-16

OTE:e-operation checks should be made each time the motorcycle is used. Such an insport time; and the added safety it assures is more than worth the time involved.

WARNINGany item in the Pre-operation check list is not working properly, have it inspece motorcycle.

rive chain

• Check chain slack.• Adjust if necessary.• Check chain condition.• Lubricate if necessary.

heels and tires

• Check for damage.• Check tire condition and tread depth.• Check air pressure.• Correct if necessary.

rake and shift pedals • Make sure that operation is smooth.• Lubricate pedal pivoting points if necessary.

rake and clutch levers • Make sure that operation is smooth.• Lubricate lever pivoting points if necessary.

enterstand, sidestand • Make sure that operation is smooth.• Lubricate pivots if necessary.

hassis fasteners • Make sure that all nuts, bolts and screws are properly tightened.• Tighten if necessary.

struments, lights, signals nd switches

• Check operation. • Correct if necessary.

idestand switch • Check operation of ignition circuit cut-off system.• If system is defective, have Yamaha dealer check vehicle.

ITEM CHECKS

OPERATION AND IMPORTANT RIDING POINTS

Starting a cold engine ....................................................................... 5-1Starting a warm engine ..................................................................... 5-2Shifting .............................................................................................. 5-3Recommended shift points (for Switzerland only) ............................. 5-3Tips for reducing fuel consumption ................................................... 5-4Engine break-in ................................................................................. 5-4Parking .............................................................................................. 5-5

EAU00372

TE:en the transmission is in the neutralition, the neutral indicator light

uld be on, otherwise have aaha dealer check the electrical cir-

Turn the starter (choke) on andcompletely close the throttle. (Seepage 3-11 for starter (choke) oper-ation.)Start the engine by pushing thestart switch.

TE:e engine fails to start, release the

rt switch, wait a few seconds, andn try again. Each starting attemptuld be as short as possible to pre-ve the battery. Do not crank the en-e more than 10 seconds on any onempt.

ERATION AND IMPORTANT RIDING POINTSEAU00373

WARNINGBecome thoroughly familiarwith all operating controls andtheir functions before riding.Consult a Yamaha dealer re-garding any control or functionthat you do not thoroughly un-derstand.Never start the engine or oper-ate it in a closed area for anylength of time. Exhaust fumesare poisonous, and inhalingthem can cause loss of con-sciousness and death within ashort time. Always make surethat there is adequate ventila-tion.Before starting out, make surethat the sidestand is up. If thesidestand is not raised com-pletely, it could contact theground and distract the opera-tor, resulting in a possible lossof control.

EAU00381*

Starting a cold engine In order for the ignition circuit cut-offsystem to enable starting, one of thefollowing conditions must be met:

� The transmission is in the neutralposition.

� The transmission is in gear withthe clutch lever pulled and thesidestand up.

EW000054

WARNING_

� Before starting the engine,check the function of the igni-tion circuit cut-off system ac-cording to the proceduredescribed on page 3-19.

� Never ride with the sidestanddown.

1. Turn the fuel cock lever to “ON”.2. Turn the key to “ON” and make

sure that the engine stop switch isset to “ ”.

3. Shift the transmission into the neu-tral position.

WhposshoYamcuit_

If thstatheshoserginatte_

ANT RIDING POINTS

Thcoputhlemstenoioiagcoswsthael_

Foceco_

EAU01258

tarting a warm engine llow the same procedure as for start- a cold engine with the exception

at the starter (choke) is not requireden the engine is warm.

OPERATION AND IMPORT

EC000034

AUTION:e oil level warning light shouldme on when the start switch isshed, and it should go off whene start switch is released. If the oilvel warning light flickers or re-ains on after starting, immediatelyop the engine, and then check thegine oil level and the vehicle forl leakage. If necessary, add enginel, and then check the warning lightain. If the warning light does notme on when pushing the startitch, or if it does not go off after

arting with sufficient engine oil,ve a Yamaha dealer check the

ectrical circuit.

. After starting the engine, move thestarter (choke) lever back halfway.

ECA00045

AUTION:r maximum engine life, never ac-lerate hard when the engine isld!

7. When the engine is warm, turn thestarter (choke) off.

NOTE:_

The engine is warm when it respondsnormally to the throttle with the starter(choke) turned off. _

SFoingthwh

5 ShShamstaetcThelus

To tralreptrav_

EAU02941

commended shift points r Switzerland only) recommended shift points duringeleration are shown in the table be-.E

TE:en shifting down two gears at ae, reduce the speed accordingly., down to 35 km/h when shifting 4th to 2nd gear).

1. SN. N

Shift point(km/h)

1st → 2nd2nd → 3rd3rd → 4th4th → 5th

23365060

PERATION AND IMPORTANT RIDING POINTS

EAU00423

ifting ifting gears lets you control theount of engine power available forrting off, accelerating, climbing hills,. gear positions are shown in the il-

tration.

TE:shift the transmission into the neu- position, press the shift pedal downeatedly until it reaches the end of itsel, and then slightly raise it.

EC000048

CAUTION:_

� Even with the transmission inthe neutral position, do notcoast for long periods of timewith the engine off, and do nottow the motorcycle for long dis-tances. The transmission isproperly lubricated only whenthe engine is running. Inade-quate lubrication may damagethe transmission.

� Always use the clutch whilechanging gears to avoid dam-aging the engine, transmission,and drive train, which are notdesigned to withstand theshock of forced shifting.

Re(foTheacclowCF-01

Whtim(e.gfrom_

hift pedaleutral position

ANT RIDING POINTS

TcoFuyotip

EAU03749*

1,000 kmoid prolonged operation above

000 r/min.

000–1,600 kmoid prolonged operation above

000 r/min.EC000052*

AUTION:ter 1,000 km of operation, the en-ne oil must be changed and the oilter element replaced.

600 km and beyonde vehicle can now be operated nor-

ally.EC000053

AUTION:� Keep the engine speed out of

the tachometer red zone.� If any engine trouble should oc-

cur during the engine break-inperiod, immediately have aYamaha dealer check the vehi-cle.

OPERATION AND IMPORT

EAU00424

ips for reducing fuel nsumption el consumption depends largely onur riding style. Consider the followings to reduce fuel consumption:

� Thoroughly warm up the engine.� Turn the starter (choke) off as

soon as possible.� Shift up swiftly, and avoid high en-

gine speeds during acceleration.� Do not rev the engine while shift-

ing down, and avoid high enginespeeds with no load on the engine.

� Turn the engine off instead of let-ting it idle for an extended lengthof time (e.g., in traffic jams, at traf-fic lights or at railroad crossings).

EAU01128

Engine break-in There is never a more important periodin the life of your engine than the periodbetween 0 and 1,600 km. For this rea-son, you should read the following ma-terial carefully.Since the engine is brand new, do notput an excessive load on it for the first1,600 km. The various parts in the en-gine wear and polish themselves to thecorrect operating clearances. Duringthis period, prolonged full-throttle oper-ation or any condition that might resultin engine overheating must be avoided.

0–Av4,

1,Av5,

Afgifil_

PaWhthesw

PERATION AND IMPORTANT RIDING POINTS

EAU00460

rking en parking, stop the engine, andn remove the key from the mainitch.

EW000058

WARNINGSince the engine and exhaustsystem can become very hot,park in a place where pedestri-ans or children are not likely totouch them. Do not park on a slope or onsoft ground, otherwise themotorcycle may overturn.

PERIODIC MAINTENANCE AND MINOR REPAIR

Owner’s tool kit ....................................................6-1Periodic maintenance and lubrication chart .........6-2Removing and installing the panel .......................6-5Checking the spark plugs ....................................6-6Engine oil and oil filter element ............................6-7Cleaning the air filter element ............................6-11Adjusting the carburetors ...................................6-12Adjusting the engine idling speed ......................6-13Adjusting the throttle cable free play ..................6-13Adjusting the valve clearance ............................6-14Tires ...................................................................6-14Cast wheels .......................................................6-17Adjusting the brake pedal position .....................6-17Rear brake light switch adjustment ....................6-18Checking the front and rear brake pads .............6-19Checking the brake and clutch fluid levels .........6-19Changing the brake and clutch fluids .................6-21Drive chain slack ................................................6-21Lubricating the drive chain .................................6-23Checking and lubricating the cables ..................6-23

Checking and lubricating the throttle grip and cable ................................................. 6-24

Checking and lubricating the brake and shift pedals ...................................................... 6-24

Checking and lubricating the brake and clutch levers .................................................... 6-24

Checking and lubricating the centerstand and sidestand ......................................................... 6-25

Checking the front fork ...................................... 6-25Checking the steering ....................................... 6-26Checking the wheel bearings ............................ 6-27Battery ............................................................... 6-27Replacing the fuses .......................................... 6-29Replacing the headlight bulb ............................. 6-29Replacing a tail/brake light bulb ........................ 6-31Replacing a turn signal light bulb ...................... 6-31Front wheel ....................................................... 6-32Rear wheel ........................................................ 6-34Troubleshooting ................................................. 6-36Troubleshooting chart ........................................ 6-37

EAU00462

TE:ou do not have the tools or experi-e required for a particular job, have

SafPer

amaha dealer perform it for you.

EW000063

WARNINGdifications not approved by

aha may cause loss of perfor-nce and render the vehicle un-e for use. Consult a Yamahaler before attempting any chang-

bricsafesiblspeareThemashoerationWECAUSVALEN

If ycycYam_

RIODIC MAINTENANCE AND MINOR REPAIR EAU00464

ety is an obligation of the owner.iodic inspection, adjustment and lu-ation will keep your vehicle in thest and most efficient condition pos-

e. The most important points of in-ction, adjustment, and lubrication explained on the following pages. intervals given in the periodic

intenance and lubrication chartuld be simply considered as a gen-l guide under normal riding condi-s. However, DEPENDING ON THEATHER, TERRAIN, GEOGRAPHI-L LOCATION, AND INDIVIDUALE, THE MAINTENANCE INTER-S MAY NEED TO BE SHORT-

ED.EW000060

WARNINGou are not familiar with motor-le maintenance work, have aaha dealer do it for you.

EAU03758

Owner’s tool kit The owner’s tool kit is located underthe seat. (See page 3-11 for seat re-moval and installation procedures.)The service information included in thismanual and the tools provided in theowner’s tool kit are intended to assistyou in the performance of preventivemaintenance and minor repairs. How-ever, additional tools such as a torquewrench may be necessary to performcertain maintenance work correctly.

If yenca Y_

MoYammasafdeaes._

1. Owner’s tool kit

AND MINOR REPAIR

EAU03685

maintenance is performed instead.

equire special tools, data and techni-

CP-03E

NETER READING (× 1,000 km) ANNUAL

CHECK10 20 30 40

1 √ √ √ √ √

2 √ √

3√ √

√ √

4 Every 20,000 km

5√ √

√ √

6 √ √ √ √

7√ √ √ √ √

Whenever worn to the limit

8√ √ √ √ √

Whenever worn to the limit

PERIODIC MAINTENANCE

Periodic maintenance and lubrication ch

OTE:� The annual checks must be performed every year, except if a kilometer-based� From 50,000 km, repeat the maintenance intervals starting from 10,000 km. � Items marked with an asterisk should be performed by a Yamaha dealer as they r

cal skills.

O. ITEM CHECK OR MAINTENANCE JOBODOM

* Fuel line • Check fuel hoses and vacuum hose for cracks or damage.

* Fuel filter • Check condition.

Spark plugs• Check condition.• Clean and regap.

• Replace.

* Valves • Check valve clearance.• Adjust.

Air filter element• Clean.

• Replace.

* Clutch • Check operation, fluid level and vehicle for fluid leakage. (See NOTE on page 6-4.) √

* Front brake• Check operation, fluid level and vehicle for fluid leakage.

(See NOTE on page 6-4.) √

• Replace brake pads.

* Rear brake• Check operation, fluid level and vehicle for fluid leakage.

(See NOTE on page 6-4.) √

• Replace brake pads.

9√ √ √ √ √

Every 4 years

10 √ √ √ √

11 √ √ √ √ √

12 √ √ √ √

13√ √ √ √

Every 50,000 km

14 Every 1,000 km and after washingthe motorcycle or riding in the rain

15√ √ √ √

Every 20,000 km

16 √ √ √ √ √

17 √ √ √ √ √

18 √ √ √ √ √

19 √ √ √ √

20 √ √ √ √

21 √ √ √ √ √

22 √ √ √ √ √

NOTER READING (× 1,000 km) ANNUAL

CHECK10 20 30 40

RIODIC MAINTENANCE AND MINOR REPAIR

* Brake hoses• Check for cracks or damage.

• Replace. (See NOTE on page 6-4.)

* Wheels • Check runout and for damage.

* Tires

• Check tread depth and for damage.• Replace if necessary.• Check air pressure.• Correct if necessary.

* Wheel bearings • Check bearing for looseness or damage.

* Swingarm• Check operation and for excessive play.

• Lubricate with lithium-soap-based grease.

Drive chain• Check chain slack.• Make sure that the rear wheel is properly aligned.• Clean and lubricate.

* Steering bearings• Check bearing play and steering for roughness. √

• Lubricate with lithium-soap-based grease.

* Chassis fasteners • Make sure that all nuts, bolts and screws are properly tightened.

Sidestand, centerstand • Check operation.• Lubricate.

* Sidestand switch • Check operation. √

* Front fork • Check operation and for oil leakage.

*Shock absorber assemblies • Check operation and shock absorbers for oil leakage.

* Carburetors • Check starter (choke) operation.• Adjust engine idling speed and synchronization. √

Engine oil • Change.• Check oil level and vehicle for oil leakage. √

. ITEM CHECK OR MAINTENANCE JOBODOME

AND MINOR REPAIR

EAU04408

y areas.

nd calipers as well as clutch master

23 √ √

24 √ √ √ √ √

25 √ √ √ √ √

26 √ √ √ √ √

NETER READING (× 1,000 km) ANNUAL

CHECK10 20 30 40

OTE:� The air filter needs more frequent service if you are riding in unusually wet or dust� Hydraulic brake and clutch service

• Regularly check and, if necessary, correct the brake and clutch fluid levels.• Every two years replace the internal components of the brake master cylinders a

and release cylinders, and change the brake and clutch fluids.• Replace the brake and clutch hoses every four years and if cracked or damaged

Engine oil filter element • Replace. √

*Front and rear brake switches • Check operation. √

Moving parts and cables • Lubricate.

*Lights, signals and switches

• Check operation.• Adjust headlight beam. √

O. ITEM CHECK OR MAINTENANCE JOBODOM

RepaTheremtenReel n

install the panelPlace the panel in the original po-sition, and then install the screw.Install the seat.

EAU01777

moving and installing the nel panel shown above needs to beoved to perform some of the main-

ance jobs described in this chapter.fer to this section each time the pan-eeds to be removed and installed.

EAU01691

Panel ATo remove the panel

1. Remove the seat. (See page 3-11for seat removal and installationprocedures.)

2. Remove the screw, and then takethe panel off.

anel A 1. Screw

AND MINOR REPAIR

CThcoSispplinnathve

TE:any spark plug shows a distinctly dif-rent color, the engine could be defec-e. Do not attempt to diagnose suchoblems yourself. Instead, have amaha dealer check the motorcycle.

. Check each spark plug for elec-trode erosion and excessive car-bon or other deposits, and replaceit if necessary.

Specified spark plug:DPR8EA-9 (NGK) or X24EPR-U9 (DENSO)

EAU03329

hecking the spark plugs e spark plugs are important enginemponents, which are easy to check.nce heat and deposits will cause anyark plug to slowly erode, the spark

ugs should be removed and checked accordance with the periodic mainte-nce and lubrication chart. In addition,e condition of the spark plugs can re-al the condition of the engine.

remove a spark plug. Remove the spark plug cap.

2. Remove the spark plug as shown,with the spark plug wrench includ-ed in the owner’s tool kit.

To check the spark plugs1. Check that the porcelain insulator

around the center electrode oneach spark plug is a medi-um-to-light tan (the ideal colorwhen the motorcycle is ridden nor-mally).

2. Check that all spark plugs installedin the engine have the same color.

If fetivprYa_

Spark plug cap (× 4) 1. Spark plug wrench

EAU04409

gine oil and oil filter ment engine oil level should be checked

ore each ride. In addition, the oilst be changed and the oil filter ele-nt replaced at the intervals specifiedhe periodic maintenance and lubri-ion chart.

check the engine oil levelPlace the motorcycle on the cen-terstand.

TE:ke sure that the motorcycle is posi-ed straight up when checking the oill. A slight tilt to the side can result inlse reading.

Start the engine, warm it up forseveral minutes, and then turn itoff.

install a spark plugMeasure the spark plug gap with awire thickness gauge and, if nec-essary, adjust the gap to specifica-tion.

Clean the surface of the sparkplug gasket and its mating sur-face, and then wipe off any grimefrom the spark plug threads.

3. Install the spark plug with thespark plug wrench, and then tight-en it to the specified torque.

NOTE:_

If a torque wrench is not available wheninstalling a spark plug, a good estimateof the correct torque is 1/4–1/2 turnpast finger tight. However, the sparkplug should be tightened to the speci-fied torque as soon as possible. _

4. Install the spark plug cap.

EneleThebefmumein tcat

Mationlevea fa_

park plug gap

park plug gap:0.8–0.9 mm

Tightening torque:Spark plug:

17.5 Nm (1.75 m·kgf)

AND MINOR REPAIR

TE:ip steps 4–8 if the oil filter element ist being replaced.

. Remove the oil filter element drainscrew to drain the oil from the oilfilter element.

. Remove the oil filter element coverby removing the bolt.

1.2.3.4.

Oil filter element drain screwBoltOil filter element cover

. Wait a few minutes until the oil set-tles, and then check the oil levelthrough the check window locatedat the bottom-right side of thecrankcase.

OTE:e engine oil should be between the

inimum and maximum level marks.

. If the engine oil is below the mini-mum level mark, add sufficient oilof the recommended type to raiseit to the correct level.

To change the engine oil (with orwithout oil filter element replace-ment)

1. Start the engine, warm it up forseveral minutes, and then turn itoff.

2. Place an oil pan under the engineto collect the used oil.

3. Remove the engine oil filler capand drain bolt to drain the oil fromthe crankcase.

Engine oil filler capEngine oil level check windowMaximum level markMinimum level mark

1. Engine oil drain bolt 1.2.3.

Install the oil filter element drainscrew, and then tighten it to thespecified torque.

Install the engine oil drain bolt, andthen tighten it to the specifiedtorque.

Add the specified amount of therecommended engine oil, andthen install and tighten the oil fillercap.

1. O2. O

ightening torque:Oil filter element drain screw:

7 Nm (0.7 m·kgf)

ightening torque:Engine oil drain bolt:

43 Nm (4.3 m·kgf)

Remove and replace the oil filterelement and O-ring.

7. Install the oil filter element coverby aligning the projection on thecover with the slot in the crank-case, installing the bolt, then tight-ening it to the specified torque.

NOTE:_

Make sure that the O-ring is properlyseated. _

il filter element-ring (× 2)

1. Projection2. Slot

Tightening torque:Oil filter element cover bolt:

15 Nm (1.5 m·kgf)

AND MINOR REPAIR

ECA00105

AUTION:� In order to prevent clutch slip-

page (since the engine oil alsolubricates the clutch), do notmix any chemical additives withthe oil or use oils of grade “CD”or higher. In addition, do notuse oils labeled “ENERGY CON-SERVING II” or higher.

� Make sure that no foreign mate-rial enters the crankcase.

11. Start the engine, and then let it idlefor several minutes while checkingit for oil leakage. If oil is leaking,immediately turn the engine offand check for the cause.

NOTE:_

After the engine is started, the engineoil level warning light should go off if theoil level is sufficient. _

EC000067

CAUTION:_

If the oil level warning light flickersor remains on, immediately turn theengine off and have a Yamaha deal-er check the vehicle. _

12. Turn the engine off, and thencheck the oil level and correct it ifnecessary.

Recommended engine oil:See page 8-1.

Oil quantity:Without oil filter element replacement:

3.0 L With oil filter element replacement:

3.35 L Total amount (dry engine):

ClTheat tmaClequewe

Lightly tap the air filter element toremove most of the dust and dirt,and then blow the remaining dirtout with compressed air as shown.If the air filter element is damaged,replace it.Insert the air filter element into theair filter case.

1. A2. S

EAU01070*

eaning the air filter element air filter element should be cleaned

he intervals specified in the periodicintenance and lubrication chart.an the air filter element more fre-ntly if you are riding in unusually

t or dusty areas.Remove the seat. (See page 3-11for seat removal and installationprocedures.)Remove panel A. (See page 6-5for panel removal and installationprocedures.)Remove the air filter case cover byremoving the screws.

4. Pull the air filter element out. 5.

ir filter case covercrew (× 4)

1. Air filter element

AND MINOR REPAIR

EC000082*

AUTION:� Make sure that the air filter ele-

ment is properly seated in theair filter case.

� The engine should never be op-erated without the air filter ele-ment installed, otherwise thepistons and/or cylinders maybecome excessively worn.

. Install the air filter case cover byinstalling the screws.

. Install the panel and the seat.

EAU00630

Adjusting the carburetors The carburetors are important parts ofthe engine and require very sophisti-cated adjustment. Therefore, most car-buretor adjustments should be left to aYamaha dealer, who has the neces-sary professional knowledge and expe-rience. The adjustment described inthe following section, however, may beserviced by the owner as part of routinemaintenance.

EC000095

CAUTION:_

The carburetors have been set andextensively tested at the Yamahafactory. Changing these settingswithout sufficient technical knowl-edge may result in poor perfor-mance of or damage to the engine. _

AdspThechefollpercha

Thespo_

EAU00635

justing the throttle cable e play throttle cable free play should

asure 3–5 mm at the throttle grip.iodically check the throttle cable play and, if necessary, have aaha dealer adjust it.

hrottle cable free play

EAU00632

justing the engine idling eed engine idling speed must becked and, if necessary, adjusted as

ows at the intervals specified in theiodic maintenance and lubricationrt.Start the engine and warm it upfor several minutes at 1,000–2,000 r/min while occasionallyrevving it to 4,000–5,000 r/min.

TE: engine is warm when it quickly re-nds to the throttle.

2. Check the engine idling speedand, if necessary, adjust it to spec-ification by turning the throttle stopscrew. To increase the engineidling speed, turn the screw in di-rection a. To decrease the engineidling speed, turn the screw in di-rection b.

NOTE:_

If the specified idling speed cannot beobtained as described above, have aYamaha dealer make the adjustment. _

AdfreThemePerfreeYam

1. Throttle stop screw

Engine idling speed:950–1,150 r/min

AND MINOR REPAIR

AThreanfromatm

Tire air pressure(measured on cold tires)

oad* Front Rear

p to 90 kg250 kPa(2.50 kgf/cm2, 2.50 bar)

250 kPa(2.50 kgf/cm2, 2.50 bar)

0 kg–maximum250 kPa(2.50 kgf/cm2, 2.50 bar)

290 kPa(2.90 kgf/cm2,

2.90 bar)

igh-speed riding250 kPa(2.50 kgf/cm2, 2.50 bar)

290 kPa(2.90 kgf/cm2,

2.90 bar)

aximum load* 203 kg

otal weight of rider, passenger, cargo and ccessories

EAU00637

djusting the valve clearance e valve clearance changes with use,

sulting in improper air-fuel mixtured/or engine noise. To prevent thism occurring, the valve clearance

ust be adjusted by a Yamaha dealer the intervals specified in the periodicaintenance and lubrication chart.

EAU00658

Tires To maximize the performance, durabil-ity, and safe operation of your motor-cycle, note the following pointsregarding the specified tires.

Tire air pressureThe tire air pressure should bechecked and, if necessary, adjustedbefore each ride.

EW000082

WARNING_

� The tire air pressure must bechecked and adjusted on coldtires (i.e., when the temperatureof the tires equals the ambienttemperature).

� The tire air pressure must beadjusted in accordance with theriding speed and with the totalweight of rider, passenger, car-go, and accessories approvedfor this model.

Beimpperticskeemin

inspection tires must be checked before each. If the center tread depth reaches specified limit, if the tire has a naillass fragments in it, or if the side-

l is cracked, have a Yamaha dealerlace the tire immediately.E

TE: tire tread depth limits may differ country to country. Always comply the local regulations.

ire sidewallire tread depth

nimum tire tread depth nt and rear)

1.6 mm

EWA00012

WARNINGcause loading has an enormousact on the handling, braking,formance and safety characteris- of your motorcycle, you shouldp the following precautions ind. NEVER OVERLOAD THEMOTORCYCLE! Operation of anoverloaded motorcycle may re-sult in tire damage, loss of con-trol, or severe injury. Make surethat the total weight of rider,passenger, cargo, and accesso-ries does not exceed the speci-fied maximum load for thevehicle. Do not carry along looselypacked items, which can shiftduring a ride. Securely pack the heaviestitems close to the center of themotorcycle and distribute theweight evenly on both sides.

� Adjust the suspension and tireair pressure with regard to theload.

� Check the tire condition and airpressure before each ride.

TireTheridetheor gwalrepCE-08

Thefromwith_

1. Ta. T

Mi(fro

AND MINOR REPAIR

� Always make sure that the valvecaps are securely installed toprevent air pressure leakage.

� Use only the tire valves andvalve cores listed below toavoid tire deflation during ahigh-speed ride.

anufacturer Size Model

unlop120/70 ZR17 (58W)

D220F ST M120/70 ZR17 M/C (58W)

ichelin120/70 ZR17 (58W)

MACADAM90X E120/70 ZR17 M/C (58W)

anufacturer Size Model

unlop180/55 ZR17 (73W)

D220 ST M180/55 ZR17 M/C (73W)

ichelin180/55 ZR17 (73W)

MACADAM90X E180/55 ZR17 M/C (73W)

FRONT & REAR

Tire air valve TR412

Valve core #9000A (original)

EW000079

WARNING� Have a Yamaha dealer replace

excessively worn tires. Besidesbeing illegal, operating themotorcycle with excessivelyworn tires decreases riding sta-bility and can lead to loss ofcontrol.

� The replacement of all wheel-and brake-related parts, includ-ing the tires, should be left to aYamaha dealer, who has thenecessary professional knowl-edge and experience.

Tire informationThis motorcycle is equipped with castwheels and tubeless tires with valves.

EW000080

WARNING_

� The front and rear tires shouldbe of the same make and de-sign, otherwise the handlingcharacteristics of the motor-cycle cannot be guaranteed.

� After extensive tests, only thetires listed below have been ap-proved for this model byYamaha Motor Co., Ltd.

1. Tire air valve2. Tire air valve core3. Tire air valve cap with seal

Thperlowmo

EAU00712

justing the brake pedal sition top of the brake pedal should beitioned approximately 40 mm below top of the footrest as shown. Peri-cally check the brake pedal position, if necessary, have a Yamahaler adjust it.

istance between brake pedal and footrest

EAU00684

WARNINGis motorcycle is fitted with su--high-speed tires. Note the fol-ing points in order to make thest efficient use of these tires.Use only the specified replace-ment tires. Other tires may runthe danger of bursting at superhigh speeds.Brand-new tires can have a rela-tively poor grip on certain roadsurfaces until they have been“broken in”. Therefore, it is ad-visable before doing anyhigh-speed riding to ride con-servatively for approximately100 km after installing a newtire.The tires must be warmed upbefore a high-speed run.Always adjust the tire air pres-sure according to the operatingconditions.

EAU03773

Cast wheels To maximize the performance, durabil-ity, and safe operation of your motor-cycle, note the following pointsregarding the specified wheels.

� The wheel rims should be checkedfor cracks, bends or warpage be-fore each ride. If any damage isfound, have a Yamaha dealer re-place the wheel. Do not attempteven the smallest repair to thewheel. A deformed or crackedwheel must be replaced.

� The wheel should be balancedwhenever either the tire or wheelhas been changed or replaced. Anunbalanced wheel can result inpoor performance, adverse han-dling characteristics, and a short-ened tire life.

� Ride at moderate speeds afterchanging a tire since the tire sur-face must first be “broken in” for itto develop its optimal characteris-tics.

AdpoThepostheodianddea

AND MINOR REPAIR

ApeaiisYafoththmac_

. Turn the adjusting nut while hold-ing the rear brake light switch inplace. To make the brake lightcome on earlier, turn the adjustingnut in direction a. To make thebrake light come on later, turn theadjusting nut in direction b.

. Install the panel.

Rear brake light switchRear brake light switch adjusting nut

EW000109

WARNING soft or spongy feeling in the brakedal can indicate the presence of

r in the hydraulic system. If there air in the hydraulic system, have amaha dealer bleed the system be-re operating the motorcycle. Air ine hydraulic system will diminishe braking performance, whichay result in loss of control and ancident.

EAU01756

Rear brake light switch adjustment The rear brake light switch, which is ac-tivated by the brake pedal, is properlyadjusted when the brake light comeson just before braking takes effect. Ifnecessary, adjust the brake light switchas follows.

1. Remove panel A. (See page 6-5for panel removal and installationprocedures.) 2

ChbrThecheifielubprowhpadble

EAU04169

ecking the brake and clutch d levels fficient brake fluid may allow air tor the brake or clutch systems, pos- causing them to become ineffec-

.ore riding, check that the brake fluidbove the minimum level mark andenish if necessary. A low brake flu-vel may indicate worn brake pads/or brake system leakage. If thee level is low, be sure to check thee pads for wear and the brake sys- for leakage.

inimum level mark

nt brake

EAU01314

ecking the front and rear ake pads front and rear brake pads must becked for wear at the intervals spec-

d in the periodic maintenance andrication chart. Each brake pad isvided with a wear indicator groove,ich allows you to check the brake wear without having to disassem-

the brake.

To check the brake pad wear, checkthe wear indicator grooves. If a brakepad has worn to the point that the wearindicator groove has almost disap-peared, have a Yamaha dealer replacethe brake pads as a set.

ChfluiInsuentesiblytiveBefis areplid leandbrakbraktem

rake pad wear indicator groove

1. Brake pad wear indicator groove

AND MINOR REPAIR

Thbere

� Be careful that water does not en-ter the brake or clutch fluid reser-voir when refilling. Water willsignificantly lower the boiling pointof the fluid and may result in vaporlock.

� Brake fluid may deteriorate paint-ed surfaces or plastic parts. Al-ways clean up spilled fluidimmediately.

� As the brake pads wear, it is nor-mal for the brake fluid level togradually go down. However, if thebrake fluid level goes down sud-denly, have a Yamaha dealercheck the cause.

OTE:e rear brake fluid reservoir is locatedhind panel A. (See page 6-5 for panelmoval and installation procedures.)

bserve these precautions:� When checking the fluid level,

make sure that the top of the brakeor clutch fluid reservoir is level.

� Use only the recommended quali-ty brake fluid, otherwise the rubberseals may deteriorate, causingleakage and poor braking or clutchperformance.

� Refill with the same type of brakefluid. Mixing fluids may result in aharmful chemical reaction andlead to poor braking or clutch per-formance.

� The brake or clutch fluid reservoirdiaphragm will lose its shape fromthe negative pressure if the fluidlevel goes down too far. Be sure toreturn the diaphragm to its originalshape before installing it into thebrake or clutch fluid reservoir.

Minimum level mark

Recommended brake and clutch fluid: DOT 4 brake fluid

ear brake

1. Minimum level mark

Clutch

ChcluHabraspemaaddandperhosbelor l

Shift the transmission into the neu-tral position.Spin the rear wheel several timesto locate the tightest portion of thedrive chain.Measure the drive chain slack asshown.

If the drive chain slack is incorrect,adjust it as follows.

rive chain slack

rive chain slack:20–30 mm

EAU03984

anging the brake and tch fluids

ve a Yamaha dealer change theke and clutch fluids at the intervalscified in the NOTE after the periodicintenance and lubrication chart. Inition, have the oil seals of the brake clutch master cylinders and cali-s as well as the brake and clutches replaced at the intervals listed

ow or whenever they are damagedeaking.

Oil seals: Replace every twoyears.Brake and clutch hoses: Replaceevery four years.

EAU00745

Drive chain slack The drive chain slack should bechecked before each ride and adjustedif necessary.

To check the drive chain slack 1. Place the motorcycle on the cen-

terstand.

AND MINOR REPAIR

1.2.3.4.

EAU03608

adjust the drive chain slack . Loosen the axle nut and the lock-

nut on each side of the swingarm.. To tighten the drive chain, turn the

adjusting bolt on each side of theswingarm in direction a. To loos-en the drive chain, turn the adjust-ing bolt on each side of theswingarm in direction b, and thenpush the rear wheel forward.

NOTE:_

Using the alignment marks on eachside of the swingarm, make sure thatboth chain pullers are in the same posi-tion for proper wheel alignment. _

EC000096

CAUTION:_

Improper drive chain slack will over-load the engine as well as other vitalparts of the motorcycle and can leadto chain slippage or breakage. Toprevent this from occurring, keepthe drive chain slack within thespecified limits. _

3. Tighten the locknuts, and thentighten the axle nut to the specifiedtorque.

LocknutDrive chain slack adjusting boltAxle nutAlignment marks

Tightening torque:Axle nut:

150 Nm (15.0 m·kgf)

LuThelubthetionoutwefoll

Thaftrid_

Todostewa_

EAU02962

ecking and lubricating the bles operation of all control cables and

condition of the cables should becked before each ride, and the ca-

s and cable ends should be lubricat-if necessary. If a cable is damageddoes not move smoothly, have a

aha dealer check or replace it.

EW000112

WARNINGage to the outer sheath may in-

ere with proper cable operation will cause the inner cable tot. Replace a damaged cable asn as possible to prevent unsafeditions.

ecommended lubricant:Engine oil

EAU03006

bricating the drive chain drive chain must be cleaned and

ricated at the intervals specified in periodic maintenance and lubrica- chart, otherwise it will quickly wear, especially when riding in dusty ort areas. Service the drive chain asows.

EC000097

UTION:e drive chain must be lubricateder washing the motorcycle oring in the rain.

Clean the drive chain with kero-sene and a small soft brush.

ECA00053

UTION: prevent damaging the O-rings, not clean the drive chain witham cleaners, high-pressureshers or inappropriate solvents.

Wipe the drive chain dry.Thoroughly lubricate the drivechain with a special O-ring chainlubricant.

ECA00052

CAUTION:_

Do not use engine oil or any otherlubricants for the drive chain, asthey may contain substances thatcould damage the O-rings. _

ChcaThethechebleed or Yam

Damterfandrussoocon_

AND MINOR REPAIR

CthThbetioreth

EAU03164

hecking and lubricating the ake and clutch levers e operation of the brake and clutchers should be checked before eache, and the lever pivots should be lu-icated if necessary.

Recommended lubricant:Lithium-soap-based grease (all-purpose grease)

EAU04034

hecking and lubricating the rottle grip and cable e operation of the throttle grip should checked before each ride. In addi-n, the cable should be lubricated orplaced at the intervals specified ine periodic maintenance chart.

EAU03370

Checking and lubricating the brake and shift pedals The operation of the brake and shiftpedals should be checked before eachride, and the pedal pivots should be lu-bricated if necessary.

CbrThlevridbr

ChceThesideacal-tlub

If tnohavpai_

EAU02939

ecking the front fork condition and operation of the front must be checked as follows at thervals specified in the periodic main-ance and lubrication chart.

check the conditionEW000115

WARNINGurely support the motorcycle so

t there is no danger of it fallingr.

ck the inner tubes for scratches,age and excessive oil leakage.

EAU03371

ecking and lubricating the nterstand and sidestand operation of the centerstand and

estand should be checked beforeh ride, and the pivots and met-o-metal contact surfaces should bericated if necessary.

EW000114

WARNINGhe centerstand or sidestand doest move up and down smoothly,e a Yamaha dealer check or re-

ChTheforkinteten

Secthaove_

Chedam

AND MINOR REPAIR

If fohapa_

. Hold the lower ends of the frontfork legs and try to move them for-ward and backward. If any freeplay can be felt, have a Yamahadealer check or repair the steer-ing.

check the operation. Place the motorcycle on a level

surface and hold it in an uprightposition.

. While applying the front brake,push down hard on the handle-bars several times to check if thefront fork compresses and re-bounds smoothly.

EC000098

AUTION:any damage is found or the frontrk does not operate smoothly,ve a Yamaha dealer check or re-ir it.

EAU00794

Checking the steering Worn or loose steering bearings maycause danger. Therefore, the operationof the steering must be checked as fol-lows at the intervals specified in the pe-riodic maintenance and lubricationchart.

1. Place a stand under the engine toraise the front wheel off theground.

EW000115

WARNING_

Securely support the motorcycle sothat there is no danger of it fallingover. _

ChThebe thetionhubsmche

EW000116

WARNINGElectrolyte is poisonous anddangerous since it contains sul-furic acid, which causes severeburns. Avoid any contact withskin, eyes or clothing and al-ways shield your eyes whenworking near batteries. In caseof contact, administer the fol-lowing FIRST AID.• EXTERNAL: Flush with plenty

of water.• INTERNAL: Drink large quan-

tities of water or milk and im-mediately call a physician.

• EYES: Flush with water for15 minutes and seek promptmedical attention.

Batteries produce explosive hy-drogen gas. Therefore, keepsparks, flames, cigarettes, etc.,away from the battery and pro-vide sufficient ventilation whencharging it in an enclosedspace.

EAU01144

ecking the wheel bearings front and rear wheel bearings must

checked at the intervals specified in periodic maintenance and lubrica- chart. If there is play in the wheel or if the wheel does not turn

oothly, have a Yamaha dealerck the wheel bearings.

EAU00800

Battery This motorcycle is equipped with asealed-type (MF) battery, which doesnot require any maintenance. There isno need to check the electrolyte or toadd distilled water.

EC000101

CAUTION:_

Never attempt to remove the batterycell seals, as this would permanent-ly damage the battery. _

AND MINOR REPAIR

ToHtehabaif tio

� KEEP THIS AND ALL BATTER-IES OUT OF THE REACH OFCHILDREN.

charge the batteryave a Yamaha dealer charge the bat-ry as soon as possible if it seems tove discharged. Keep in mind that thettery tends to discharge more quicklythe motorcycle is equipped with op-nal electrical accessories.

store the battery. If the motorcycle will not be used

for more than one month, removethe battery, fully charge it, andthen place it in a cool, dry place.

. If the battery will be stored formore than two months, check it atleast once a month and fullycharge it if necessary.

. Fully charge the battery before in-stallation.

. After installation, make sure thatthe battery leads are properly con-nected to the battery terminals.

EC000102

CAUTION:_

� Always keep the batterycharged. Storing a dischargedbattery can cause permanentbattery damage.

� To charge a sealed-type (MF)battery, a special (con-stant-voltage) battery charger isrequired. Using a conventionalbattery charger will damage thebattery. If you do not have ac-cess to a sealed-type (MF) bat-tery charger, have a Yamahadealer charge your battery.

6ReThe(SeinsIf a

EAU04189

placing the headlight bulb s motorcycle is equipped with artz bulb headlight. If the headlight

b burns out, replace it as follows.Remove the headlight unit by re-moving the screws.

1. M2. S3. H4. I5. T6. S

crew (× 2)

EAU04410*

placing the fuses fuse box is located under the seat.e page 3-11 for seat removal andtallation procedures.) fuse is blown, replace it as follows.

Turn the key to “OFF” and turn offthe electrical circuit in question.Remove the blown fuse, and theninstall a new fuse of the specifiedamperage.

EC000103

CAUTION:_

Do not use a fuse of a higher amper-age rating than recommended toavoid causing extensive damage tothe electrical system and possibly afire. _

3. Turn the key to “ON” and turn onthe electrical circuit in question tocheck if the device operates.

4. If the fuse immediately blowsagain, have a Yamaha dealercheck the electrical system.

ReThiquabul

ain fuseignaling system fuseeadlight fuse

gnition fuseurn signal light fusepare fuse (× 2)

Specified fuses:Main fuse: 40 AIgnition fuse: 15 ASignaling system fuse: 15 AHeadlight fuse: 15 ATurn signal light fuse: 15 A

ND MINOR REPAIR

2EC000105

UTION:not touch the glass part of thedlight bulb to keep it free fromotherwise the transparency of

glass, the luminosity of the bulb, the bulb life will be adversely af-ed. Thoroughly clean off any dirt fingerprints on the headlightb using a cloth moistened withhol or thinner.

Install the headlight bulb cover,and then connect the coupler.Install the headlight unit by install-ing the screws.Have a Yamaha dealer adjust theheadlight beam if necessary.

o not touch this area.

PERIODIC MAINTENANCE A

. Disconnect the headlight coupler,and then remove the bulb cover.

3. Unhook the headlight bulb holder,and then remove the defectivebulb.

EW000119

WARNING_

Headlight bulbs get very hot. There-fore, keep flammable products awayfrom a lit headlight bulb, and do nottouch the bulb until it has cooleddown. _

4. Place a new headlight bulb intoposition, and then secure it withthe bulb holder.

Do heaoil, theandfectandbulalco_

Headlight couplerBulb cover

1. Headlight bulb holder 1. D

Remove the defective bulb bypushing it in and turning it counter-clockwise.Insert a new bulb into the socket,push it in, and then turn it clock-wise until it stops.Install the lens by installing thescrew.

ECA00065

UTION: not overtighten the screw, other-e the lens may break.

1. T urn signal light bulb

EAU04411

placing a tail/brake light lb

Remove the seat. (See page 3-11 forseat removal and installation proce-dures.)Remove the socket (together with thebulb) by turning it counterclockwise.Remove the defective bulb by push-ing it in and turning it counterclock-wise.Insert a new bulb into the socket,push it in, and then turn it clockwiseuntil it stops.Install the socket (together with thebulb) by turning it clockwise.Install the seat.

EAU03497

Replacing a turn signal light bulb

1. Remove the turn signal light lensby removing the screw.

Dowis_

ail/brake light bulb socket 1. Screw 1. T

AND MINOR REPAIR

. Loosen the front wheel axle pinchbolt, then the wheel axle.

. Place the motorcycle on the cen-terstand.

. Pull the wheel axle out, and thenremove the wheel.

1. Front wheel axle pinch boltWheel axle

EAU04412

ront wheel

remove the front wheelEW000122

WARNING� It is advisable to have a Yamaha

dealer service the wheel.� Securely support the motor-

cycle so that there is no dangerof it falling over.

. Disconnect the speedometer ca-ble from the front wheel.

2. Remove the brake hose holdersby removing the bolts.

3. Remove the brake calipers by re-moving the bolts.

ECA00047

CAUTION:_

Do not pull the brake lever after thebrake caliper has been removed,otherwise the brake pads will beforced shut. _

Speedometer cable 1. Bolt (× 3)2. Brake hose holder3. Front brake caliper

Left Right

Install the brake hose holders byinstalling the bolts.Take the motorcycle off the cen-terstand so that the front wheel ison the ground.Tighten the wheel axle, then thefront wheel axle pinch bolt and thebrake caliper bolts to the specifiedtorques.

Connect the speedometer cable.Push down hard on the handlebarseveral times to check for properfork operation.

ightening torques:Wheel axle:

72 Nm (7.2 m·kgf)Front wheel axle pinch bolt:

20 Nm (2.0 m·kgf)Brake caliper bolt:

40 Nm (4.0 m·kgf)

EAU04360

install the front wheel Install the speedometer gear unitinto the wheel hub so that the pro-jections mesh with the slots.

2. Lift the wheel up between the forklegs.

NOTE:_

Make sure that the slot in the speedom-eter gear unit fits over the retainer onthe fork leg. _

3. Insert the wheel axle.4. Install the brake calipers by install-

ing the bolts.

NOTE:_

Make sure that there is enough spacebetween the brake pads before install-ing the brake calipers onto the brakediscs. _

1. Speedometer gear unit retainer

AND MINOR REPAIR

. Remove the axle nut and thebrake caliper by removing thebolts.

ECA00082

AUTION: not apply the brake after the

ake caliper has been removed,herwise the brake pads will berced shut.

. Loosen the locknuts, and then turnthe drive chain slack adjusting bolton each side of the swingarm fullyin direction a.

. Push the wheel forward, and thenremove the drive chain from therear sprocket.

1.2.3.

Wheel axle

EAU04413

ear wheel

remove the rear wheel EW000122

WARNING� It is advisable to have a Yamaha

dealer service the wheel.� Securely support the motor-

cycle so that there is no dangerof it falling over.

. Loosen the axle nut and the brakecaliper bolts.

2. Disconnect the brake torque rodfrom the brake caliper bracket byremoving the nut and the bolt.

3. Place the motorcycle on the cen-terstand.

Dobrotfo_

LocknutDrive chain slack adjusting boltAxle nut

1. Bolt2. Brake torque rod3. Nut4. Brake caliper bracket5. Brake caliper6. Bolt (× 2)

Thedisins_

Tighten the axle nut, brake caliperbolts and brake torque rod nut tothe specified torques.

ightening torques:Axle nut:

150 Nm (15.0 m·kgf)Brake caliper bolt:

40 Nm (4.0 m·kgf)Brake torque rod nut:

23 Nm (2.3 m·kgf)

TE: drive chain does not need to be

assembled in order to remove andtall the rear wheel.

While supporting the wheel andthe brake caliper bracket, pull thewheel axle out.Remove the brake caliper bracketand the wheel.

EAU03895

To install the rear wheel 1. Place the wheel and the brake cal-

iper bracket in the original position.2. Insert the wheel axle through the

brake caliper bracket and wheelfrom the right-hand side, and theninstall the axle nut.

3. Install the drive chain onto the rearsprocket, and then adjust the drivechain slack. (See page 6-22 fordrive chain slack adjustment pro-cedures.)

4. Connect the brake torque rod tothe brake caliper bracket by in-stalling the bolt and the nut.

5. Install the brake caliper by install-ing the bolts.

NOTE:_

Make sure that there is enough spacebetween the brake pads before install-ing the brake caliper onto the brakedisc. _

6. Take the motorcycle off the cen-terstand so that the rear wheel ison the ground.

AND MINOR REPAIR

TAla froincoexloThrefoseredethknprUmlikinca

EAU01008

roubleshooting though Yamaha motorcycles receivethorough inspection before shipmentm the factory, trouble may occur dur-

g operation. Any problem in the fuel,mpression, or ignition systems, forample, can cause poor starting and

ss of power.e following troubleshooting chart

presents a quick and easy procedurer checking these vital systems your-lf. However, should your motorcyclequire any repair, take it to a Yamahaaler, whose skilled technicians havee necessary tools, experience, andow-how to service the motorcycleoperly.se only genuine Yamaha replace-ent parts. Imitation parts may looke Yamaha parts, but they are oftenferior, have a shorter service life andn lead to expensive repair bills.

PERIODIC

EAU01297

TroubleshootEW000125

WARNING_

Keep away open stem. _

not start. ression.

The engine does not start.Have a Yamaha dealercheck the vehicle.

engine does not start.ck the battery.

n the throttle halfway and operateelectric starter.

Check the fuethe fuel tank.

Operate the e

2. Comp

Remove the sand check the

3. Ignitio

Operate the e

4. Batter

MAINTENANCE AND MINOR REPAIR

ing chart

flames and do not smoke while checking or working on the fuel sy

l level in

elThere is enough fuel.

There is no fuel.

Check the compression.

Supply fuel. The engine doesCheck the comp

lectric starter.

ressionThere is compression.

There is no compression.

Check the ignition.

Have a Yamaha dealercheck the vehicle.

park plugs electrodes.

n Wipe off with a dry cloth and correct thespark plug gaps, or replace the spark plugs.

Have a Yamaha dealer check the vehicle. TheChe

lectric starter.

yThe engine turns over quickly.

The engine turns over slowly.

The battery is good.

Check the battery lead connections,and charge the battery if necessary.

WetOpethe

MOTORCYCLE CARE AND STORAGE

Care .................................................................................................. 7-1Storage .............................................................................................. 7-4

EAU03430

aningECA00010

UTION:

CaWhreve

Avoid using strong acidic wheelcleaners, especially on spokedwheels. If such products areused on hard-to-remove dirt, donot leave the cleaner on the af-fected area any longer than in-structed. Also, thoroughly rinsethe area off with water, immedi-ately dry it, and then apply acorrosion protection spray.Improper cleaning can damagewindshields, cowlings, panelsand other plastic parts. Useonly a soft, clean cloth orsponge with mild detergent andwater to clean plastic.

noloble.eveusenotifrommodoethe moand

TORCYCLE CARE AND STORAGE

re ile the open design of a motorcycleals the attractiveness of the tech-gy, it also makes it more vulnera- Rust and corrosion can developn if high-quality components ared. A rusty exhaust pipe may go un-ced on a car, however, it detracts the overall appearance of a

torcycle. Frequent and proper cares not only comply with the terms ofwarranty, but it will also keep your

torcycle looking good, extend its life optimize its performance.

Before cleaning1. Cover the muffler outlets with plas-

tic bags after the engine hascooled down.

2. Make sure that all caps and coversas well as all electrical couplersand connectors, including thespark plug caps, are tightly in-stalled.

3. Remove extremely stubborn dirt,like oil burnt onto the crankcase,with a degreasing agent and abrush, but never apply such prod-ucts onto seals, gaskets, sprock-ets, the drive chain and wheelaxles. Always rinse the dirt anddegreaser off with water.

ARE AND STORAGE

ter riding in the rain, near the sea or salt-sprayed roadsnce sea salt or salt sprayed on roadsring winter are extremely corrosive inmbination with water, carry out thellowing steps after each ride in thein, near the sea or on salt-sprayedads.

TE:lt sprayed on roads in the winter may

main well into spring.

. Clean the motorcycle with coldwater and a mild detergent, afterthe engine has cooled down.

ECA00012

AUTION: not use warm water since it in-

eases the corrosive action of thelt.

. After drying the motorcycle, applya corrosion protection spray on allmetal, including chrome- and nick-el-plated, surfaces to prevent cor-rosion.

MOTORCYCLE C

� Do not use any harsh chemicalproducts on plastic parts. Besure to avoid using cloths orsponges which have been incontact with strong or abrasivecleaning products, solvent orthinner, fuel (gasoline), rust re-movers or inhibitors, brake flu-id, antifreeze or electrolyte.

� Do not use high-pressure wash-ers or steam-jet cleaners sincethey cause water seepage anddeterioration in the following ar-eas: seals (of wheel and swing-arm bearings, fork and brakes),electric components (couplers,connectors, instruments,switches and lights), breatherhoses and vents.

� For motorcycles equipped witha windshield: Do not use strongcleaners or hard sponges asthey will cause dulling orscratching. Some cleaningcompounds for plastic mayleave scratches on the wind-shield. Test the product on asmall hidden part of the wind-shield to make sure that it doesnot leave any marks. If the wind-shield is scratched, use a quali-ty plastic polishing compoundafter washing.

After normal useRemove dirt with warm water, a milddetergent, and a soft, clean sponge,and then rinse thoroughly with cleanwater. Use a toothbrush or bottlebrushfor hard-to-reach areas. Stubborn dirtand insects will come off more easily ifthe area is covered with a wet cloth fora few minutes before cleaning.

AfonSiducoforaro

Docrsa_

ECA00013

UTION:Apply spray oil and wax spar-ingly and make sure to wipe offany excess.Never apply oil or wax to anyrubber and plastic parts, buttreat them with a suitable careproduct.Avoid using abrasive polishingcompounds as they will wearaway the paint.

TE:sult a Yamaha dealer for advice ont products to use.

OTORCYCLE CARE AND STORAGE

er cleaningDry the motorcycle with a chamoisor an absorbing cloth.Immediately dry the drive chainand lubricate it to prevent it fromrusting.Use a chrome polish to shinechrome, aluminum and stainless-steel parts, including the exhaustsystem. (Even the thermally in-duced discoloring of stainless-steel exhaust systems can be re-moved through polishing.)To prevent corrosion, it is recom-mended to apply a corrosion pro-tection spray on all metal,including chrome- and nickel-plat-ed, surfaces.Use spray oil as a universal clean-er to remove any remaining dirt.Touch up minor paint damagecaused by stones, etc.Wax all painted surfaces.Let the motorcycle dry completelybefore storing or covering it.

EWA00001

WARNING_

� Make sure that there is no oil orwax on the brakes or tires. Ifnecessary, clean the brakediscs and brake linings with aregular brake disc cleaner or ac-etone, and wash the tires withwarm water and a mild deter-gent.

� Before operating the motor-cycle test its braking perfor-mance and cornering behavior.

Conwha_

ARE AND STORAGE

ShAldrag

a. Remove the spark plug caps andspark plugs.

b. Pour a teaspoonful of engine oilinto each spark plug bore.

c. Install the spark plug caps onto thespark plugs, and then place thespark plugs on the cylinder headso that the electrodes are ground-ed. (This will limit sparking duringthe next step.)

d. Turn the engine over several timeswith the starter. (This will coat thecylinder walls with oil.)

e. Remove the spark plug caps fromthe spark plugs, and then installthe spark plugs and the spark plugcaps.

EWA00003

WARNING prevent damage or injury fromarking, make sure to ground theark plug electrodes while turninge engine over.

MOTORCYCLE C

torage

ort-termways store your motorcycle in a cool,y place and, if necessary, protect itainst dust with a porous cover.

ECA00014

AUTION:� Storing the motorcycle in a

poorly ventilated room or cover-ing it with a tarp, while it is stillwet, will allow water and humid-ity to seep in and cause rust.

� To prevent corrosion, avoiddamp cellars, stables (becauseof the presence of ammonia)and areas where strong chemi-cals are stored.

Long-termBefore storing your motorcycle forseveral months:

1. Follow all the instructions in the“Care” section of this chapter.

2. Turn the fuel cock lever to “ON”.3. Drain the carburetor float cham-

bers by loosening the drain bolts;this will prevent fuel deposits frombuilding up. Pour the drained fuelinto the fuel tank.

4. Fill up the fuel tank and add fuelstabilizer (if available) to preventthe fuel tank from rusting and thefuel from deteriorating.

5. Perform the following steps to pro-tect the cylinders, piston rings, etc.from corrosion.

Tospspth_

OTORCYCLE CARE AND STORAGE

Lubricate all control cables andthe pivoting points of all levers andpedals as well as of the sidestand/centerstand.Check and, if necessary, correctthe tire air pressure, and then liftthe motorcycle so that both of itswheels are off the ground. Alterna-tively, turn the wheels a little everymonth in order to prevent the tiresfrom becoming degraded in onespot.Cover the muffler outlets with plas-tic bags to prevent moisture fromentering them.

9. Remove the battery and fullycharge it. Store it in a cool, dryplace and charge it once a month.Do not store the battery in an ex-cessively cold or warm place (lessthan 0 °C or more than 30 °C). Formore information on storing thebattery, see page 6-28.

NOTE:_

Make any necessary repairs beforestoring the motorcycle. _

SPECIFICATIONS

Specifications .................................................................................... 8-1Conversion table ............................................................................... 8-5

EAU01038

SpCS-01

oil API Service SE, SF, SG or higher

ent 3.0 L

t 3.35 L

gine) 4.2 L

-20 -10 0 10 20 30 40 50 ˚C

SAE 10W-30

SAE 15W-40

SAE 20W-40

SAE 20W-50

SAE 10W-40

tor oils that do not contain anti-frictionger car motor oils (often labeledVING II”) contain anti-friction additivestch and/or starter clutch slippage, result-onent life and poor engine performance.

ECIFICATIONS

ecifications E

odel XJR1300

imensions

Overall length 2,175 mm (except for N, S)

2,250 mm (for N, S)

Overall width 775 mm

Overall height 1,115 mm

Seat height 790 mm

Wheelbase 1,510 mm

Ground clearance 120 mm

Minimum turning radius 2,800 mm

asic weight (with oil and full uel tank) 247 kg

Engine type Air-cooled 4-stroke, DOHC

Cylinder arrangement Forward-inclined parallel 4-cylinder

Displacement 1,251 cm3

Bore × stroke 79.0 × 63.8 mm

Compression ratio 9.7:1

Starting system Electric starter

Lubrication system Wet sump

Engine oil

Recommended engine classification

Quantity

Without oil filter elemreplacement

With oil filter elemenreplacement

Total amount (dry en

CAUTION:

Be sure to use momodifiers. Passen“ENERGY CONSERwhich will cause cluing in reduced comp

SPECIFICATIONS

1st 2.857

2nd 2.000

3rd 1.571

4th 1.292

5th 1.115

Double cradle

25.5 °

100 mm

Tubeless tire

120/70 ZR17 (58W)

120/70 ZR17 M/C (58W)

odel Dunlop / D220F ST M

Michelin / MACADAM90X E

Tubeless tire

180/55 ZR17 (73W)

180/55 ZR17 M/C (73W)

odel Dunlop / D220 ST M

Michelin / MACADAM90X E

Air filter Dry element

Type REGULAR UNLEADED GASOLINE ONLY

Fuel tank capacity 21 L

Fuel reserve amount 4.5 L

Carburetor

Manufacturer MIKUNI

Model × quantity BSR37 × 4

Spark plug

Manufacturer/model NGK / DPR8EA-9 or DENSO / X24EPR-U9

Gap 0.8–0.9 mm

Clutch type Wet, multiple-disc

Transmission

Primary reduction system Spur gear

Primary reduction ratio 1.750

Secondary reduction system Chain drive

Secondary reduction ratio 2.167

Number of drive chain sprocket teeth (front/rear) 18/39

Transmission type Constant-mesh 5-speed

Operation Left foot

Gear ratio

Chassis

Frame type

Caster angle

Manufacturer/m

Dual disc brake

Right hand

Single disc brake

Right foot

Telescopic fork

Swingarm

Coil spring / oil damper

Coil spring / gas-oil damper

130 mm

110 mm

T.C.I. (digital)

A.C. generator

put 13.5 V, 28 A @ 5,000 r/min

ECIFICATIONS

Maximum load* 203 kg

Tire air pressure (measured on cold tires)

Up to 90 kg*

Front 250 kPa (2.50 kgf/cm2, 2.50 bar)

Rear 250 kPa (2.50 kgf/cm2, 2.50 bar)

90 kg–maximum*

High-speed riding

* Total weight of rider, passenger, cargo and accessories

Wheels

Type Cast wheel

Size 17 × MT 3.50

17 M/C × MT 3.50

Type Cast wheel

Size 17 × MT 5.50

17 M/C × MT 5.50

Brakes

Operation

Suspension

Springs/shock absorbers

Wheel travel

Electrical system

Ignition system

Charging system

Standard out

SPECIFICATIONS

Battery

Model GT14B-4

Voltage, capacity 12 V, 12 Ah

Headlight type Quartz bulb (halogen)

Bulb voltage, wattage × quantity

Headlight 12 V, 60/55 W × 1

Tail/brake light 12 V, 5/21 W × 2

Auxiliary light 12 V, 4 W × 1

Turn signal light 12 V, 21 W × 4

Meter lighting 12 V, 1.7 W × 4

Neutral indicator light 12 V, 1.7 W × 1

High beam indicator light 12 V, 3.4 W × 1

Oil level warning light 12 V, 1.7 W × 1

Turn signal indicator light 12 V, 1.7 W × 2

Main fuse 40 A

Headlight fuse 15 A

Signaling system fuse 15 A

Ignition fuse 15 A

Turn signal light fuse 15 A

CoCS-0

nversion tableTEM TO IMPERIAL SYSTEM

nit Conversion factor Imperial unit

× 7.233× 86.794× 0.0723× 0.8679

ft·lbin·lbft·lbin·lb

× 2.205× 0.03527

× 0.6214 mi/h

× 0.6214× 3.281× 1.094× 0.3937× 0.03937

miftydinin

× 0.03527× 0.06102× 0.8799× 0.2199

oz (IMP liq.)cu·inqt (IMP liq.)gal (IMP liq.)

× 55.997× 14.2234× 1.8 + 32

lb/inpsi (lb/in2)°F

ECIFICATIONS

EAU03941

nversion table 3E

l specification data in this manual are listed in SI andTRIC UNITS.

e this table to convert METRIC unit values to IMPERIALit values.

ample:

ETRIC VALUE CONVERSION FACTOR

IMPERIAL VALUE

2 mm × 0.03937 = 0.08 in

CoMETRIC SYS

Metric u

Torque

m·kgfm·kgfcm·kgfcm·kgf

Weight kgg

Speed km/h

Distance

kmmmcmmm

Volume,Capacity

cc (cm3)cc (cm3)L (liter)L (liter)

Miscellaneouskg/mmkgf/cm2

CONSUMER INFORMATION

Identification numbers ....................................................................... 9-1Key identification number .................................................................. 9-1Vehicle identification number ............................................................. 9-1Model label ........................................................................................ 9-2

EAU01039

IdeRec

EAU01043

hicle identification number vehicle identification number is

mped into the steering head pipe.ord this number in the space pro-d.

TE: vehicle identification number isd to identify your motorcycle andy be used to register your motor-le with the licensing authority inr area.

ehicle identification number

vehel lavideorddeacle

1.CA-02

3.CA-01

NSUMER INFORMATIONEAU02944

ntification numbers ord the key identification number,icle identification number and mod-bel information in the spaces pro-d below for assistance when

ering spare parts from a Yamahaler or for reference in case the vehi-is stolen.

KEY IDENTIFICATION NUMBER:E

VEHICLE IDENTIFICATION NUMBER:

MODEL LABEL INFORMATION:E

EAU01041

Key identification number The key identification number isstamped into the key tag. Record thisnumber in the space provided and useit for reference when ordering a newkey.

VeThestaRecvide

Theusemacycyou_

1. Key identification number 1. V

MER INFORMATION

MThunreRthwpa

EAU01050

odel label e model label is affixed to the frameder the seat. (See page 3-11 for seatmoval and installation procedures.)ecord the information on this label ine space provided. This informationill be needed when ordering sparerts from a Yamaha dealer.

Model label

ttakakakb

akakakakak

brbrenntn

ivivAC

ight switch ..............................................3-5uggage strap holders ...........................3-16

ain switch/steering lock .........................3-1odel label ..............................................9-2

eutral indicator light ...............................3-2

il level warning light ...............................3-2

anel, removing and installing..................6-5arking.....................................................5-5art locations ...........................................2-1ass switch..............................................3-4eriodic maintenance and lubrication chart ......................................................6-2re-operation check list............................4-1

afety information ....................................1-1eat .......................................................3-11hifting.....................................................5-3hift pedal................................................3-6hift points (for Switzerland only) .............5-3hock absorber assemblies, adjusting ..............................................3-15idestand...............................................3-17park plugs, checking ..............................6-6pecifications...........................................8-1peedometer unit.....................................3-3

AAirAn

BBaBrBrBr

luBrBrBrBrBr

CCaCaCaCe

aCluCo

DDimDrDr

e pedal..............................................3-7e pedal position, adjusting ..............6-17

les, checking and lubricating............6-23uretors, adjusting............................6-12.........................................................7-1

terstand and sidestand, checking d lubricating .....................................6-25ch lever..............................................3-5version table......................................8-5

mer switch .........................................3-4e chain, lubricating...........................6-23e chain slack....................................6-21djusting ..........................................6-22hecking ..........................................6-21

HHandlebar switches ................................. 3-4Hazard switch.......................................... 3-4Headlight bulb, replacing ....................... 6-29Helmet holder ........................................ 3-12High beam indicator light ......................... 3-2Horn switch ............................................. 3-4

IIdentification numbers ............................. 9-1Idling speed, adjusting........................... 6-13Ignition circuit cut-off system.................. 3-17Indicator and warning lights ..................... 3-2

KKey identification number ........................ 9-1

SSSSSSS

ilter element, cleaning......................6-11theft alarm ........................................3-4

ery ...................................................6-27e and clutch fluid levels, checking...6-19e and clutch fluids, changing...........6-21e and clutch levers, checking and ricating ............................................6-24e and shift pedals, checking and ricating ............................................6-24e lever...............................................3-7e light switch (rear), adjusting .........6-18e pads, checking.............................6-19

EEngine break-in ....................................... 5-4Engine oil and oil filter element ................ 6-7Engine stop switch................................... 3-5

FFront fork, adjusting............................... 3-13Front fork, checking ............................... 6-25Fuel ......................................................... 3-9Fuel cock............................................... 3-10Fuel consumption, tips for reducing ......... 5-4Fuel gauge .............................................. 3-3Fuel tank breather hose......................... 3-10Fuel tank cap........................................... 3-8Fuses, replacing .................................... 6-29

StaStaStaStaSteStoSto

TTaTaThTh

luTirToTroTroTuTuTu

ol kit..................................................... 6-1ubleshooting..................................... 6-36ubleshooting chart ............................ 6-37

rn signal indicator lights ....................... 3-2rn signal light bulb, replacing ............. 6-31rn signal switch.................................... 3-4

lve clearance, adjusting..................... 6-14hicle identification number ................... 9-1

eel bearings, checking...................... 6-27eel (front).......................................... 6-32Installing........................................... 6-33Removing .......................................... 6-32eel (rear) .......................................... 6-34Installing........................................... 6-35Removing......................................... 6-34

rter (choke) lever .............................. 3-11rting a cold engine.............................. 5-1rting a warm engine............................ 5-2rt switch.............................................. 3-5ering, checking ................................. 6-26rage.................................................... 7-4rage compartment ............................ 3-13

chometer ............................................. 3-3il/brake light bulb, replacing ............... 6-31rottle cable free play, adjusting .......... 6-13rottle grip and cable, checking and bricating............................................ 6-24es ...................................................... 6-14

Wheels.................................................. 6-17

E_5GK_Consumer.fm Page 11 Wednesday, June 13, 2001 1:03 PM

5EA-28199-E4

XJR1300

OWNER’S MANUAL

PRINTED ON RECYCLED PAPER

YAMAHA MOTOR CO., LTD.

PRINTED IN JAPAN2001 . 8 - 0.3 × 1 CR

owner’s manual - yamaha xjr cz | czech xjr owner's site · protective clothing is as...

Documents

ammeraal beltech modular light_cat… · for all your...

rubber conveyor belts, power transmission belts, industrial...

straight line belts • turn belts • wire cloth

december 2015 the swallow leaping to the growler · in imsa...

conveyor belts - nedalibyaconveyor belts schouten conveyor...

changes in the list of subdivision names and code...

ipl, cz 3815/ cz 4217/ cz 42175, 2006-08, ride mower (turf

fan belts other belts car aftermarket m08526c m

despiece yamaha xjr 1300cc_5wm1_2003.pdf

recent advancements in the development of molecular ...12.7...

fan belts other belts car aftermarket distribution m08526g m

prezentace aplikace powerpoint · cz uk it cz uk it cz uk...

chronous belts sprockets keyless bushings special belts aves...

accessories quality standards manual - · pdf filethis...

belts for the box and carton folding industry€¦ · •...

cz-70 (cz-50) pistol explained

conveyor belts power steering belts transmark

synchronous belt solutions for packaging technology ·...

a research stand for measuring friction … research stand...

yamaha xjr manual