safety check course...check shifter flappy paddle then check if the red light is on when you push...

Safety Check-CourseIN THIS SLIDESHOW YOU WILL TAKE PART OF HOW A SAFETY CHECK

IS PREFORMED CORRECTLY

CASTER - ENGINEERS IN THE FRONT SEAT

The list to perform a Safety

CheckThe safety check is divided into fiveparts, every part has to be approved in order for the safety check to be completed.

Three parts includes a check of the pit area and upper platform which is around the simulator.

Two parts include the start up and safety check which is to be made on the computer.

And the last driving check is made witha driver in the drivers seat.

Let´s begin!

CASTER - ENGINEERS IN THE FRONT SEAT

Pit area

CASTER - ENGINEERS IN THE FRONT SEAT

Make sure that the white spot on the pawn is aligned to the white spot on the ground everywhere around on all three of the attachments

CASTER - ENGINEERS IN THE FRONT SEAT

1. Inspect ground attachment bolts

Same as previous, make sure that the white spot on very bolt is near the white spot on the plate, to make sure no bolt has loosened up.

CASTER - ENGINEERS IN THE FRONT SEAT

2. Inspect actuator fixation (top & bottom)

Top Bottom

Check if wiring and connectors are attached and not moving except around its attachment.

CASTER - ENGINEERS IN THE FRONT SEAT

3. Inspect wiring & connectors of all actuators

4. Inspect computer cabinet

CASTER - ENGINEERS IN THE FRONT SEAT

Make sure the computer cabninets are in the right position

5. Inspect stand and its fixation

CASTER - ENGINEERS IN THE FRONT SEAT

6. Inspect access bridge and its fixation

CASTER - ENGINEERS IN THE FRONT SEAT

There is no bridge, therefore it should look like the picture to the left.

6. Inspect pedalbox wiring & connectors7. Inspect pedalbox fixation

CASTER - ENGINEERS IN THE FRONT SEAT

See if the pedals are fixed and the wiring and connectors are attached.

66

8. Check brake system for oil leaks9. Inspect even brake pedal travel

CASTER - ENGINEERS IN THE FRONT SEAT

Oil leaks

Obs! Check for oil leaks under both cylinders

9

8

10. Inspect throttle pedal endstops11. Inspect clutch pedal endstops

CASTER - ENGINEERS IN THE FRONT SEAT

10 11

12. Inspect screen attachements

CASTER - ENGINEERS IN THE FRONT SEAT

Make sure the screens are still attached – not moving.

Upper platform

CASTER - ENGINEERS IN THE FRONT SEAT

1. Inspect general condition of seat and fixation2. Inspect seatbelt and attachment functioning

CASTER - ENGINEERS IN THE FRONT SEAT

Attachments

Attachments

2

3. Inspect subwoofer underneeth the seat

CASTER - ENGINEERS IN THE FRONT SEAT

Make sure that the subwoofer is fix and no screws has come lose.

4. Inspect seating position adjuster

CASTER - ENGINEERS IN THE FRONT SEAT

Check the position adjuster.

5. Inspect steering wheel6. Inspect general condition of H-pattern shifter7. Inspect fixation of H-pattern to upper platform8. Clean upper platform

CASTER - ENGINEERS IN THE FRONT SEAT

Check shifter flappy paddle

Then check if the red light is on when you push the flappy paddle.

H-pattern shifter

5

7

Start up

CASTER - ENGINEERS IN THE FRONT SEAT

1. Switch on motion system2. Realese E-stop and press red reset button3. Start operator computer

CASTER - ENGINEERS IN THE FRONT SEAT

Switch on motion system

This is how it looks when the E-stop is realesed and the red button is pushed(not shining)

Operator computer

1

23

4. Start Session Manager on desktop

CASTER - ENGINEERS IN THE FRONT SEAT

5. Start all computers

CASTER - ENGINEERS IN THE FRONT SEAT

They can also be started trough ”Session manager”.

6. Check if all computers have Racer running7. Start a new heat and select demo (no driver)

CASTER - ENGINEERS IN THE FRONT SEAT

6. If Racer is running then all the screens on the simulator have a black background withthe Chalmers logo on the middle screen

7.1

7.2

8. Inspect if motion is properly working

CASTER - ENGINEERS IN THE FRONT SEAT

Motion is when the simulator moves while driving. It can be turned off so you can drive without movement.

The motion can be checked by listening for noise and see that the movement is as expected

1. Check if simulator comes up OK 2. Check the car and track loads OK3. Check if spectator view is OK4. Check if the platform moves OK

CASTER - ENGINEERS IN THE FRONT SEAT

What to check while testing demo

Driving check

CASTER - ENGINEERS IN THE FRONT SEAT

Driving Check for test driver

CASTER - ENGINEERS IN THE FRONT SEAT

1. Test motion (It acts normal)2. Test steering (Force feedback)3. Test pedals4. Test shift pedals and manual H-pattern gearbox5. Check audio system

Let´s go!

CASTER - ENGINEERS IN THE FRONT SEAT