sip trunking goldtel aria ip - 60 what connection ? co via gw or voib card? aria – ip 60
Post on 21-Dec-2015
216 Views
Preview:
TRANSCRIPT
SIP TrunkingGoldtel
ARIA IP - 60
What connection ? CO via GW or VoIB Card?
Aria – iP 60
This document explains the configuration that is required on ERICSSON-LG PABX systems when
SIP trunks are configured using the Goldtel SIP trunk service.
Basic call setup (Incoming & Outgoing calls) was tested with CLI (Calling Line Identification)
presentation.
Please note that this document is Service Provider specific (Goldtel Telecom) and some of the
Details below are used as examples only.
This document is only applicable to the ERICSSON-LG range of PABX systems.
TEST SETUP CONFIGURATION
Goldtel Service Provider Details
The following information was received from the Service Provider (Goldtel) to complete the tests:
SIP/Proxy/Registrar IP: 196.7.219.35 and 196.7.219.35
SIP Port Number : 5060 (UDP)
Introduction
Sip account User@Domain Authorization Name Password Phone Number
27876300184@196.7.219.35 27876300184 cNxxxxxxxx 27876300184
27876300184@196.7.219.35 27876300185 cNxxxxxxxx 27876300185
Slot Configuration PGM 101 - 103
Right Click
If we require 8 VoIP lines then this setting
= 8
Numbering PlanPGM 104 - 109
What if theis is not [1]
PGM 108 Gateway IP = Router IP
IP Settings
165.165.165.1
PABX IP Address
192.165.55.202
ADSL Router IP Address
The same range as the PBX
PGM 140/141/143/146
CO Line Configuration
CO Line Configuration
Co grp 1 = Voip / SIP Trunks on Slot 10 (1st Choice o/g)Telkom or other SP lines will be allocated to CO Grp2
CO Line Configuration
Mode 141
Mode 142
Mode 146
This parameter defines the DID digit conversion process for DID digits received from the ISDN or IP CO line.
After removal of digits, Flexible button 5, the DID number treatment can be a simple conversion (0), no conversion (1) or simple conversion with table look-up (2). PGM231
CO Line Configuration
Mode 146CO Attr |||
PGM 111 for all extension
Station Configuration
This parameter determines the caller id for a station when employing SIP for a call.When using SIP, the caller id is based on the CLIP/COLP (PGM 143 Flexible button 1 and 2) or the User ID defined from the SIP User ID Table index (PGM 501) entered here.{500&501 with 340}
Invalid entry Message- Mode 111 FK23 = 1 Sip User IDAlso Mode 231- 087 630 0 184 The last 3 digits = 184 OpenNow set day & night destination ringing = 100
PGM 111 for fax in and out going call
Station Configuration
PGM 114
Station Configuration
PGM 340/341 Firewall IP = WAN IP of the Router
VOIP Configuration
IP address of the Gateway
Card VoIB
ADSL Router IP Address
PGM 340 SIP ATT 1 (Actually PGM 500)
VOIP Configuration
SIP Trunk RegistrationPGM 340 SIP ATT 11 (Actually PGM 501)
PGM 322
Net working CO line configuration
PGM 200/201
COLP Table configuration
PGM 231
Flexible DID Table
Invalid entry Message- Mode 111 FK23 = 1 Sip User ID Error code “Cause 400”Also Mode 231- 087 630 0 184 The last 3 digits = 184 OpenNow set day & night destination ringing = 100
PGM 450 Flex 15
N.B. After this step please reset IP60 system
COLP Table configuration
087 6300 551
Mode 200 Mode 201 Mode 231
Mode 143 – DiD=2DiD REM = 1DiD Enblock =1
On
Mode 146 – DiD RCV =3DiD Dig = #***
#1**
Mode 231 – 550 – Ring Sta 100=150
END
top related