tender document for supply of raw material/ · pdf filetender form nit no:- 04 of 2015 tender...
Post on 23-Mar-2018
221 Views
Preview:
TRANSCRIPT
ESTD 1960
Opp. Kala Kendra, Bikram Chowk, Jammu, J&K-180004 Website:- www.govtpolytechnicjammu.edu.in
email:- govtpolyjammu@gmail.com
Fax:-0191-2435373 Ph. 0191-2457891
NIT NO: 04 of 2015
TENDER DOCUMENT NO:- GPJ/F-678/1576-78
DATED:- 30.12.2015
“TENDER DOCUMENT FOR SUPPLY OF RAW MATERIAL/
TOOLS FOR VARIOUS GOVT. POLYTECHNICS OF
JAMMU DIVISION”
TENDER FORM
NIT No:- 04 of 2015 TENDER DOCUMENT NO:- GPJ/ F-678/1576-78
DATED:-30.12.2015
To
The Principal Government Polytechnic Bikram Chowk, Jammu
Sir/Madam,
I ______________________________________________________________
from M/S______________________________ hereby submit the tender for the supply
of following items for _____________________________ departments as per the detail
attached herewith. I further affirm that I have read and fully understood the tender notice
and agree to abide by all the terms and conditions laid therein, which are signed as a
token of acceptance. The undersigned hereby offers to execute supply of items as per
specification against which I have quoted the rates and for which this tender may be
accepted at the rates stated there in and subject to the terms & conditions set forth for
such items as may be ordered by various Principals of Govt. Polytechnics of Jammu
Division.
Yours Faithfully,
Signature____________________________________________________________________
Date________________________________________________________________________
Name of the Tenderer _________________________________________________________
Amount of CDR with Bank name and Date:__________________________________________
M/S ________________________________________________________________________
Phone __________________________ Mobile ______________________________________
Fax ____________________________
Fax:-0191-2435373 Ph.:-0191-2457891
Er. Ritu Jamwal Principal
ESTD: 1960
GOVERNMENT OF JAMMU AND KASHMIR GOVERNMENT POLYTECHNIC JAMMU
Opp. Kala Kendra, Bikram Chowk, Jammu Website:- www.govtpolytechnicjammu.edu.in
Email:- govtpolyjammu@gmail.com
NOTICE INVITING TENDER NIT No:- 04 of 2015 Dated:- 30/12/2015
For and on behalf of the Governor of Jammu and Kashmir State sealed tenders affixed with Rs 5/- revenue stamps are invited from Registered dealers/Authorized suppliers/ Authorized Dealers of manufacturers for the supply of Raw material/Tools for various Govt. Polytechnics of Jammu division (Jammu, Samba, Kathua, Reasi, Udhampur, Poonch, Doda, Ramban, Kishtwar) as per list enclosed in tender document. The tender should be accompanied with the earnest money in the form of CDR/FDR pledged to the Principal Government Polytechnic, Bikram Chowk Jammu of any scheduled bank without which tender will be out rightly rejected as per the following detail:-
S. No. Name of Tender Earnest money (in Rupees)
Cost of Tender documents (in Rupees)
1. Tender for Computer/ Electrical/Electronics (Raw material)
Rs.5000/- Rs.200/-
2. Tender for General Workshop/Mechanical/ Automobile Engg (Raw material)
Rs.5000/- Rs.200/-
3. Tender for Physics/Chemistry /Medical Lab Technology/Stationery (Raw material)
Rs.5000/- Rs.200/-
The tender document containing list of raw material required and Terms & conditions can be had from the office of the undersigned against the cost mentioned above on any working day after the publication of this notice in newspaper upto 4:00 PM. The complete sealed tender document with quoted rates at specified place in the document along with the earnest money for an amount shown above against each tender in the form of CDR/FDR should reach the office of the Principal Government Polytechnic, Jammu by hand/Registered post on or before 20-01-2016 upto 4:00 PM. In case that the last day of receipt happens to be a non working day, next working day shall be considered as the last day of receipt of the tender documents. The tender will be opened on 21-01-2016 at Govt. Polytechnic, Bikram Chowk Jammu at 12:00 Noon in presence of the tenderers who may like to be present on opening date. The undersigned shall have the authority to accept or reject any or all tenders without assigning any reasons thereof. The tender document shall be available on official website of this institute www.govtpolytechnicjammu.edu.in and on www.jkdte.org of Directorate of Technical Education, J&K.
No: GPJ/F-678/1576-78 Dated: 30/12/2015 (Er. Ritu Jamwal)
(Chairman D.L.P.C) Principal, Govt. Polytechnic, Jammu
Copy to: 1. The Director, Technical Education, J&K, Jammu/Srinagar for information. 2. The Joint Director, Information Department Jammu with the request to kindly get the notice widely
publicized in at least three leading Local English/Hindi News Paper preferably in Daily Excelsior, State Times, Greater Kashmir, Danik Jagran etc for minimum three days.
3. The General Manager, Govt. Press Jammu for publication in the coming issue of the Govt. Gazette. 4. Tender File.
Detailed tender Notice/terms and conditions for supply of RAW MATERIAL for various Govt. Polytechnics of Jammu Division (2015-16)
For and on behalf of the Governor of Jammu and Kashmir State sealed tenders affixed with Rs 5/- revenue stamps are invited from Registered dealers/Authorized suppliers/ Authorized Dealers of manufacturers for the supply of Raw material for various departments of Govt. Polytechnics of Jammu division as per list enclosed in tender document. The tender should be accompanied with the earnest money in the form of CDR/FDR pledged to the Principal Government Polytechnic, Jammu of any scheduled bank without which tender will be out-rightly rejected as per the following detail and should reach office of the undersigned by or before 20-01-2016 upto 4:00 PM.
S. No. Name of Tender Earnest money (in Rupees)
Cost of Tender documents (in Rupees)
1. Tender for Electrical/Computer/Electronics (Raw material)
Rs.5000/- Rs.200/-
2. Tender for General Workshop/Mechanical/ Automobile Engg (Raw material)
Rs.5000/- Rs.200/-
3. Tender for Physics/Chemistry /Medical Lab Technology/Stationery (Raw material)
Rs.5000/- Rs.200/-
TERMS AND CONDITIONS:-
1. Tender must be enclosed in a properly sealed envelope and addressed to the Principal, Govt. Polytechnic, Bikram Chowk, Jammu indicating the department for which tender is applied.
2. The single rate should be quoted F.O.R Govt. Polytechnics of Jammu Division i.e Jammu, Kathua, Samba, Reasi, Udhampur, Poonch, Ramban, Doda and Kishtwar inclusive of taxes (VAT, Entry Tax etc.)/ All charges/ Freights, Insurance, forwarding and incidental charges, if any wherever applicable.
3. Each tender must be accompanied with a CDR/FDR as indicated in the abbreviated tender notice, pledged in favour of the Principal, Govt. Polytechnic, Jammu without which the tender will not be entertained /accepted Cheque/Demand Draft instead of CDR/FDR will be rejected straight away without any notice. The Tenderers who may download the tender documents from the website should submit the postal order or Demand draft as cost of each tender document along with the tender failing which the tender will be rejected.
4. The successful tenderer shall have to make the supplies of the ordered quality, specification, make, mark, size etc. within 30 days from the date of the supply order. The payment will be made by the respective college only after receipt and verification of the items. Goods other than the approved quality and specification will not be accepted.
5. Tenderers should quote the rates without any erasing, overwriting, cutting etc. Mutilated tenders shall not be accepted/ entertained.
6. The rates should be quoted only on the tendered items on the prescribed tender document obtained from the office/downloaded from website. The rates quoted on other than the tender document will not be accepted and the tender will be rejected.
7. Tenders received after the prescribed date and time will not be entertained. Any tender received after the date though posted in time but delayed during transit due to postal delay or otherwise will not be entertained and shall be returned to the addressee. However, in case the last date happens to be Strike or holiday then the next working day will be treated as last date for receipt of these tenders.
8. The tenders should be accompanied with relevant literature wherever required. The make and model should be mentioned with the items for which the rates have been quoted.
9. In case the successful tenderers fails to supply the goods of the prescribed specifications, make, mark, quality etc. within the stipulated time period, the CDR of such firm/tenderer will be forfeited in favour of the Govt. and the department shall be at liberty to arrange the supplies through re-tender or otherwise.
10. In case any dispute/doubt/deference/question arise between the tenderer and the department regarding interpretation of any of the terms and conditions or any other matter relating to the purchase, the same shall be referred to the Director Technical Education (J&K Govt.) or any other officer nominated by him in this behalf for arbitration, whose decision in the matter shall be final, conclusive and binding upon the parties. All the disputes between the parties involving legal intervention shall be subject to the jurisdiction of J&K High Court.
11. The rates shall remain valid upto one year from the date of finalization of rate contract. 12. The intending tenderers should provide latest Income Tax returns, VAT clearance Certificate up
to 31-03-2015 and Registration certificate. 13. The tenderer should clearly mention warranty/guarantee period of the product. 14. The quantity mentioned in the tender document may increase or decrease as per the availability
of funds and other related variations. 15. The tenderer shall have to provide training to the identified officials of the department to
operate the machinery at the place of installation wherever necessary. 16. In case of specification, the committee shall have the right to take decision in consultation with
experts at the time of the finalization of rates. 17. The small scale industries units of the state who desire to quote the rates will be dealt in
accordance with State Industrial Policy. 18. In case rates of any items are available on DGS&D rate contract or on any Govt. approved rate
contract at the time of approval, the cases will be decided accordingly. 19. The Principal, Govt. Polytechnic, Jammu reserves the right to accept or reject any tender or all
the tenders or part thereof without assigning any reason thereof.
(Er. Ritu Jamwal) (Chairman, D.L.P.C) Principal
Govt. Polytechnic Jammu
Fax:-0191-2435373 Ph. 0191-2457891
Er. Ritu Jamwal Principal
ESTD: 1960
GOVERNMENT OF JAMMU AND KASHMIR
GOVERNMENT POLYTECHNIC JAMMU
Opp. Kala Kendra, Bikram Chowk, Jammu Website:- www.govtpolytechnicjammu.edu.in
Email:- govtpolyjammu@gmail.com
Items required for General Workshop/ Mechanical/ Automobile Engg.
Department
Note:- Rate to be quoted FOR Govt. Polytechnics of Jammu Division i.e Jammu, Samba, Udhampur inclusive of taxes (VAT, Entry Tax etc.) / All charges/ Freights, Insurance, forwarding and incidental charges
GENERAL WORKSHOP
S.NO NAME OF EQUIPMENT SPECIFICATIONS TENTATIVE QTY PRICES PER UNIT INCLUSIVE OF TAXES
1. Crosscut Saw with handle (JK/Eastman/Taparia/Pye)
Blade length: 450mm(Approx)
Blade Material: High quality Steel with hardness approx.=RC52
Handle: wooden or high quality plastic
05
2. Adjustable Hacksaw with Blade(JK/Eastman/Taparia/Pye)
Blade Size: 8”-12”
Frame/Handle: Soft PVC/Wood
05
3. Iron Jack Plane with wooden handle(JK/Eastman/Taparia/Pye)
Cut Iron: High carbon steel
Body: Cast Iron
Size: 8",14",18"
05 each
4. Rebate Plane adjustable blade type(JK/Eastman/Taparia/Pye)
Cutter material: High carbon steel
Blade Size:1/2", 3/4",1"
05 each
5. Iron/Wooden smoothening Plane(JK/Eastman/Taparia/Pye)
Cutter material: High carbon steel
Size: 9", Blade Size :50 mm(Approx)
10
6. Claw Hammer(JK/Eastman/Taparia/Pye)
Head: Forged high carbon steel
Handle: hard wood and polished/lacquer coated or Cushioned Plastic
Weight Approx.: 250 gms. &450 gms.
05 each
7. Wooden Mallet with handle(JK/Eastman/Taparia/Pye)
Weight: 300gms, 500gms & 800gms (Approx).
05 each
8.
Ball peen Hammer Head: Forged high carbon steel
Handle: hard wood and polished/lacquer coated or Cushioned Plastic
weight Approx. : 250 gms.,450 gms.
05 each
9.
Cross peen Hammer Head: Forged high carbon steel
Handle: hard wood and polished/lacquer coated or Cushioned Plastic.
Weight Approx. : 100 gms.,300gms.
05 each
10.
Carpenter Pincer Forged carbon steel/chrome Vanadium steel with high quality rubber/PVC
Size. : 8", 9"
05 each
GROUP 2
11.
C Clamp Body: SG iron.
Screw and lever: High quality Steel.
Size: 4", 6", 8" 05 each
12. Corner Clamp Body: SG iron.(Spheroidal Graphite CI)
Jaw Width:2”/ 4" 05
13.
T- Bar Clamp Body : Carbon steel
Head &Jaws: cast iron/malleable iron.
Size: 3'’ & 4'’
05 each
14.
Carpenter vice quick grip type
Body: SG iron.
Head &Jaws : cast iron/malleable iron
Size: 6",8",12"
05 each
15. Adjustable Marking Gauge Size: 6" and scale graduated in mm 05
16. Adjustable Mortise Gauge Size: 6" and scale graduated in mm 05
17.
Firmer Chisel Set Material: Heat treated and forged alloy steel
Size(mm): 6,10,12,16,20,24,30 05 each
18.
Mortise Chisel Set ( bevel Edge) (JK/Eastman/Taparia/Pye)
Material: Heat treated and forged alloy steel
Size(mm): 6,10,12,15,20,25 05 each
19.
Paring Chisel Set Material: Heat treated and forged alloy steel
Size(mm): 6,10,12,16,20,24,30 05 each
20. Gouge Chisel Set Material: Heat treated and forged alloy
steel Size(mm): 6,10,12,16,20,24,30 05 each
21. Adze Size: 3" angle edge , weight: 1kg 05
22. Trammel Size:300mm 05
23.
Triangular File(JK/Eastman/Taparia/Pye)
Handle: High quality rubber/plastic for grip
Size: 100,150,200mm 05 each
24.
Flat Basterd File(JK/Eastman/Taparia/Pye)
Single cut and double cut type
Size: 12" 10
25.
Try Square(JK/Eastman/Taparia/Pye)
Blade Material: cast steel/SS with inch and mm Graduation
Size: 6", 8", 12 ",18" 05 each
26. Four Fold wooden Rule Size: 2" with inch and mm graduation 10
27. Measuring Tape/Pocket Tape
Tape Length: 3m, 5m 05 each
28.
Water stone/Oil stone
Grit size: 800,1000,1200
Dimension:15cm×5cm×2.5cm(Approx) 05 each
29. Two Sided Diamond Plate
Grit size: 1000,1600
Dimension:9"×5"×.8"(Approx) 05 each
30. Adjustable Honing Guide Width of Grip:3 to 65 mm 05
31. Spring Caliper (Inside & outside type) (JK/Eastman/Taparia/Pye)
Size: 150 mm(Approx)
10
32. wing Compass Size: 300mm(Approx) 10
33. Sprit Level 0.5 mm accuracy without magnet. 10
34.
Screw Driver Set(JK/Eastman/Taparia/Pye)
Size: 3mm,4mm,6mm,8mm,10mm;Lenghth: 100,150,200,250,300mm Engineering pattern
05 sets
35. Tool Trolley With 7 drawers or more 02
36. Round Die Set for thread cutting with Handle
Size: 1/2" to 1" 05
37. Tap Set with Handle Size: 1/4", 1/2", 3/4",1" 02 each
38. Bar Bender Bending Capacity: 8mm to 13 mm 05
39. Pipe Bender Hydraulic Type
Bending Capacity: 1/2" to 2" 05
40. Pipe Vice Hinged Type
Size: 2"-3" 10
41.
Fitters Vice Fixed and Swivel Base Type, chrome plated screws
size: 3", 6"
05 each
42. Surface Plate 400×400 mm, Steel 05
43. Adjustable Angle Plate 20×10 cm 03
44. Anvil (single bick type) Approx. Weight: 50 Kg with stand 02
45. Adjustable Wrench(JK/Eastman/Taparia/Pye)
Size: 6", 8" 05 each
46. Plier Box & slip Joint Type Size: 10" 05
47. Adjustable pipe Wrench(JK/Eastman/Taparia/Pye)
Size: 6", 8",12”,14”,18” 05+02 each
48. Ring End Spanner Set(JK/Eastman/Taparia/Pye)
Size: 6- 32 mm 05k+01
49. Open Ended spanner JK/Eastman/Taparia/Pye)
3mm to 32mm 01each
50. Double End Spanner Set(JK/Eastman/Taparia/Pye)
Size: 6×7mm to 27× 32 mm 05
51. Flat cold Chisel Size: 6", 8", 10" 05 each
52. Round Chisel Size: 6", 8", 10" 05 each
53. Number Punch Size: 5mm, 0-9 05
54. Center Punch Size: 4" 05
55. Plumb Bob Weight: 50 Gms 05
56. Bevel Square Size: 12" 05
57. Plumber Saw Size: 300mm 05
58. Cutting Pliers(JK/Eastman/Taparia/Pye)
Size: 200 mm" 10
59. Flat Rough File(JK/Eastman/Taparia/Pye)
Size: 14" single and double cut type 10
60. Flat Smooth File(JK/Eastman/Taparia/Pye)
Size: 6",8",12" 05 each
61. Half Round Smooth File(JK/Eastman/Taparia/Pye)
Size: 12" 10
62. Half Round Rough File(JK/Eastman/Taparia/Pye)
Size: 12" 10
63. Square Rough & smooth File(JK/Eastman/Taparia/Pye)
Size: 12" 10
64. Knife Edge File Smooth Size: 8" 10
65. Odd Leg Caliper Size:150mm 10
66. Micrometer ouside and Inside(JK/Eastman/Taparia/Pye)
Size: 0-150 mm, digital/Analog 05
67. Digital Vernier Caliper Set(JK/Eastman/Taparia/Py
Main Scale Size: 150 mm, 300mm, 450mm
02 each
e) Least count: 0.01mm
68. Steel Rule Size: 150 mm, 300mm, 450mm with Inch
and mm graduation 05 each
69. v block with Clamp Size: 6"×7”×7” 10
70. Depth Gauge(JK/Eastman/Taparia/Pye)
Size: 12" 05
71. Engineering Try Square Set(JK/Eastman/Taparia/Pye)
Size: 8",12",18" with Inch and mm graduation 05 each
72. Combination Pliers(JK/Eastman/Taparia/Pye)
Size : 6" 10
73. Allen Key Set(JK/Eastman/Taparia/Pye)
size: 24, 25, 27, 30, 32, 36, 42 and 46 mm. 05 set
74. Ball peen Hammer with Handle
Weight: 800gms, 1000gms. 05 each
75. Pocket Tape Size: 3m & 5m 05 each
76. Height Gauge Size: 12". 10
77. Sledge Hammer with handle
Weight: 1000gms. 10
78. Sprit Level Magnetic type Size : 300 mm 10
79. Chisel diamond point Size: 6 x 150mm 05
80. V block V bock with clamp
Size: 3” 05
81. Work Bench A Heavy wooden top (8'×3') , fixed with
2 swivel type bench vices 100mm Jaw 05
82. Welding Partition Screen Dark fiber type 10
83. Welding Goggles Standard safety goggles for welding
Shatterproof polycarbonate lenses with anti-scratch coating
Soft foam protection guards dust and perspiration from the eye
20
84.
Welding Gloves Good quality Leather and Kevlar stitched
Trigger-patch on index finger for extended wear
Reinforced palm patch.
Size: Medium and large 10
85. Arm & leg sleeves Good quality Leather and Kevlar stitched 10
86.
Apron Leather
size: Medium and Large
Quality leather to withstand sparks and spatter
10
87.
Welding Helmet As per applicable safety standards
Viewing Area – 9.22 sq. in. / 3.85 x 2.38 in (97 x 60 mm)
10
88. Smithy Tongs Size: 12", Flat mouth type 10
89. Chipping Hammer with handle
Weight: 250gms. 500gms. 05 each
90. Smithy Try Square Size: 18"×12" 10
91. Measuring Gauge Wire gauge and Sheet Gauge 10
92. Steel Wire Brush Size: 6",9" 10 each
93. Divider Firm Joint Size: 8" 10
94. Fix Spanner set Size: (10 Nos) 6 mm to 27 mm drop
forged 05 sets
95. Bench Vice Size: 4"& 6" Jaw ,swivel type 10
96. Sprit Level Magnetic type Size : 300 mm 05
97.
Anvil Weight: 50kg with stand, single bick long pattern 05
98. Mobile Weld fume Extractor Capture: 12 ft. extraction arm
Distance to arc: Up to 18 in. with extraction arm
Filter type: self cleaning
Input voltage: 220-240V, 50 Hz
01
99. Stakes & stake Holder set Hatchet stake , Pipe stake, Funnel stake, Half moon Stake, Mandrel, side stack, round bottom and ball head stake, tinman horse stake with heads.
Note: Each type of stake to be provided in a set of 3 different sizes and 1 stake holder with lock pin and 1 star stake plate
01 set
100. Hand lever Shear cutter Blade Length 300mm.
Cutting capacity: 5mm Sheet 6mm Bar,13mm Round
02
101. Swage Block Caste Iron swage Block :20"×20"×7" with cast Iron stand
05
102. Swage Block Caste Iron swage Block :15"×15"×5" with cast Iron stand
05
103. Cast Iron Mandrel Cone 75mm Dia. Tapering to 220mm Dia. 600mm High
02
104. Hot or Square Punch Size:1/4",3/8",1/2" 05 each
105. Wing Compass Size: 8" 05
106. Spring Divider(JK/Eastman/Taparia/Pye)
Size: 6"
05
107. Tin snip/Tin Cutter- Heavy duty
Quality PVC grip, Size: 10" to 12" 10
108. Steel Scriber set single ended light duty: 4"
Single ended heavy duty:6"
Double Ended, a needle point one end and a chisel other end:6"
Double Ended, one straight point and other bent at 90 deg( Light and Heavy Duty Type): 8"
10
109. Rubber Mallet with handle weight: 500gms, 800gms 05 each
110. Hand operated sheet folding machine
Folding Capacity : 1 m length , 1.6 mm thick sheet of metal 01
111. Scientific Calculator with solar
12
112. Engineering Drawing Models
(Shaft Couplings,Foot step bearing 01 each
113. Electric Kettle 1.5L 01
114. LED Lamps 9 V,16W 5
115. Ball Bearing 6201 and 6202 5 each
116. Hammer 5Kg,4Kg,3Kg,2Kg,1Kg 2 each
117. Fuller set (Top and Bottom) Size: 1/8",1/4", 3/8" 05 each
118. Straight peen/ Smiths Hammer
Weight: 300gms, 500gms, 800gms,1500gms
05 each
119. Straight peen/ Smiths Hammer
500gm,1000gms 05 each
120. Sledge Hammer 1000gms, 1500gms,2000gms 05 each
121. Handies Standard as per requirement 10
122. Poker Standard as per requirement 10
123. Smiths Forge Shovel Features: Long Handled
Protective Qualities: Rust Resistant
Care and Cleaning: Wipe Clean With a Damp Cloth
Blade Dimensions: 10.0 " L x 8.0 " W
Dimensions: 64.0 " L x 10.0 " W x 5.0 " H
05
124. VernierCaliper Main scale :18", LC=0.02mm 05
125.
Gloves High temperature application Kevlar Gloves with polymer grip
10
126. Wall Clock 12
127. Steel Tub Galvanized Volume: 20 Liters 02
128. Storage Bin Plastic Size:2'×1 1/2'×3' 05
129. G.I. Plane Sheet 24 gauge, 26 gauge, 28 gauge 8X4ft. 2 each
130. M.S. Sheet 22 gauge, 24 gauge, 26 gauge
900mmx2500mm 2 each
131. MS Flat (50mm x 6mm) 2 Quintal
132. MS Round (6mm,8mm, 12mm, 25mm, 32mm) 2 each
133. Cast Iron Block Rectangular
150mmx100mmx50mm 5 each
134. Cast Iron Block Square 100mmx100mmx100mm 5 each
135. Soldering Wire 60x40 2 pkt
136. MS Square Bar (10mm, 12mm) 2 each
137. Aluminium round Bar 12 mm 3 lengths
138. Aluminium flat 1 ¼”x 8 mm 5 lengths
139. Wood Kail 2’X2”X2” 5
140. M.S. Electrodes 3.15x350mm (10 no. s.w.g.) 10 pkts.
141. Wire Nail ½”, 1”, 2”, 3” 2 Kg each
142. Insulation Tape Steel Grip 2 dz.
143. Cutting Oil as per BIS : 1115-1986 20 litre
144. Soap Lifebouy 24 piece
145. Aluminium Rivets ¼”, 1/8” 2 kg each
146. Brass Rod 10 SWG 2 pkt.
147. Filler Rod 10 SWG 2 Pkt
148. Flux Powder for tining ½ Kg pack
2 pkt.
149. Boring Bar (Boring Tool) 01
150. Parting Tool Holder with tool
01
151. Socket Set with reversible ratchet
3mm to 32mm,drive3/4” 01
152. PVC Clamp ½”, ¾”, 1” 12 eeach
153. Steel Screw ½”, ¾”, 1”, 2”, 3” 1 pkt. each
154. G.I. Pipe ½”, ¾”, 1” 3 length each
155. G.I. Socket ½”, ¾”, 1” 12 each
156. G.I. Tee ½”, ¾”, 1” 12 each
157. G.I. Elbow ½”, ¾”, 1” 12 each
158. G.I. Union ½”, ¾”, 1” 12 each
159. G.I.nipple ½”x4” 12 nos
160. Valve cock 1/”, ¾” and 1” 10nos
161. Angle valve ½” 10nos
162. Suter (Thread) 5 dz
163. Safeda 250gm 12
164. Welding Glass (Black, White)
50 piece
165. Sand Paper 60, 80no. , 100 no. 12 each
166. CFL 15, 25, 40 (W) Havels/ Anchor/ Philips 6 each
167. Bench Vice 3” Jaw 08
168. Nail 1/2”, 17 No. 1”, 2”,3”,4” 1 kg
169. H.S.S Drill Bits 4mm,5mm,6mm,7mm,8mm,9mm,10mm. 10 each
170. H.S.S.taper shank drill bit 13mm,15mm,16mm,18mm,22mm 10each
171. Drill Chuck 0-12mm with key 5nos
172. PVC Pipe 15mm for watering 200m.
173. Fevi Col 1kg packing
174. Lakh dana 1 Kg
175. Molasses(Raab) 100 Kg
176. Moulding Boxes 1x1ft.
2x2ft (cope and Drag) 05 each
177. Paint Black, White, Grey(Asian,Burger,Nerolac)
1 liter packing 20lts each
178. Paint brush 3”,4”,6” 10 each
179. Wood Primer 10 lts
180. Metal Primer 10lts
181. PVC pipe 4” (Heavy duty) 10nos
182. Collar Socket 4” (Heavy duty) 15nos
183. Tee 4” (Heavy duty) 5nos
184. Bend 4” (Heavy duty) 15nos
185. Solvent Solution 500gms
186. English Seat W.c 5nos
187. Cistern Low level 5nos
188. Seat cover 5nos
189. Jet Pipe heavy 20mm
190. Seat cover Clamp 20pairs
191. White Cement 5kgs
192. White zinc Safeda 2kgs
193. Bib Cock ½” Iron 20nos
194. Bib Cock ½” C.I. 20nos
195. PVC connection pipe 18” 50nos
196. PVC Connection pipe 24” 20nos
197. Face Heavy Duty 50nos
198. Disk Face 50nos
199. Ball cock ½ Brass 50pcs
200. Ball valve ½ Brass 50nos
201. Tank Nipple brass ½”,3/4”,1”,1x1/4” 20 each
202. Motor Pump 0.5 H.p.
1.0 H.p 01 each
203. Check valve Brass ½”,3/4”,1”,2”,3” 03 each
204. Main Hole !2’x12” C.I 04nos
205. Sewing Machine with stand Make: USHA /Singer/Toshiba/Brother 10 Nos
MECHANICAL/ AUTOMOBILE ENGINEERING DEPARTMENT
S.NO NAME OF EQUIPMENT SPECIFICATIONS TENTATIVE QTY PRICES PER UNIT INCLUSIVE OF TAXES
1 R-22 Gas 10 kg each 02 cylinder
2 R-134a Gas 500 gms each 10 Cylinder
3 Copper tube ¼ “ 05 roll
4 Copper tube ½ “ 05 roll
5 Copper tube 5/8 “ 05 roll
6 Copper brazing rod 02 kg
7 Compressor 1.5 rotary 01 No.
8 Compressor 1.5 reciprocating 01 No.
9 Compressor 1/6 Hp 02 No.
10 Car A/c compressor 01 No.
11 Butane gas for brazing 20 cylinder
12 Butane gas brazing torch 04 Nos.
13 Flare Nut ¼, 3/8, ½, 5/8 20 Nos. Each
14 Toner for Work-Center Pro 423,428 Xerox Make 01 no
15 Cartridge for HP printer 1007 (88 A) 01 no
16 Cartridge for HP printer 1005 (34 A) 01 No
17 Hydraulic oil (Grade 68) 100 ltrs
18 Grease (Castrol) 5 Kg
19 Cotton Waste 10 Kg
20 Dhoti 10 mtrs
21 Weight Pans 24 Nos.
22 Drawing Pins 10 packs
23 Thread 20 rolls
24 Weights (Steel) 5,10,20,50,100,200,
500 gms
12 each
25 Specimens of Brass, Bronze, Mild
Steel, HSS, Gun Metal, Aluminium
12 each
26 Button Cells, Battery Cells, Pencil
Cells
24 Each
27 UPS Batteries (12 V) 120 Nos.
28 LPG Cylinder (5 Kg) with pipe,
regulator, blow torch
for brazing
1 No
29 Scanner HD 1 No
30 Brake oil 25 lts
31 Hydrometer 36 nos
32 Engine oil 25 lts
33 Hose Pipe 20mts
34 Gear oil SAE 90 10lts
35 Grease White 5kgs
36 Tubeless puncture kit 02kits
37 Solution Tube 1pkt
38 Garage tool kit trolley type 5 drawer 02nos
39 Piston ring ecpander 01no
40 Piston ring compressor 01no
41 Spark plug spanner 02
42 High Voltage discharge tester 02nos
43 Vacuum gauge for engine cylinder 01no
44 Compression gauge for engine
cylinder
01no
45 Universal Puller 01no
46 Tyre inflation pressure gauge 1.wall mounted type
2.Pen type
01 each
47 Lever Type grease gun 300cc upto 6000psi 01no
48 Hot Puncture machine Standard size 01no
49 Roller for making cold puncture Standard size 01no
50 Oil spray Can 250cc 02nos
(Er. Ritu Jamwal)
(Chairman, D.L.P.C) Principal
Govt. Polytechnic, Jammu
top related