tm_intro & kks gesch

Geregu IIGeregu II – GTPP / NIA8053 x SSC5-2000E

Basic Operation Training

General Introduction

Volume 1-

Basic Operation Training

Introduction

BOT for Combined Cycle Power Plants

Table of contents:Page

1. Basic configuration 04

2. KKS 12

3. Siemens Documentation Structure 28

BOT for Combined Cycle Power Plants (CCPP)

1. Basic configuration

Comprehensive portfolio and services:from primary energy to power distribution

Main components of a power plant (example single shaft)

HRSG

Transformer

Control Room and Administration Building

Raw/Fire Water

Demin Water

Turbine Building

Workshop and Storage Building

Demin Water Plant

Feedwater Pumps

Filter, Metering &Gas Preheating

Laboratory

Power Control Center

Emergency Diesel

Generator Breaker

Gas Reducing

Siemens combined cycle power plants: Development of efficiency

CCPP Killingholme, 2 x 450 MW

CCPP Didcot “B” 1, 2,710 MW + 702 MW

CCPP Mainz-Wiesbaden, > 400 MW

> 58%CC efficiency

SGT5-2000E(V94.2)

CCPP Irsching 4, > 530 MW

SGT5-8000H

> 60%CC efficiency

> 56%CC efficiency

> 52%CC efficiency

SGT5-4000F(V94.3A)

2001 1992 1996 2011

SGT5-4000F(V94.3A)

Why Combined Cycle Power Plant ? The advantage of CCPP

Plant principle CCPP (single shaft)

Plant principle CCPP (multi shaft, simplified)

Electricalpower GT-generator

Gas turbine

Heat recoverysteam generator

ST-generatorSteam turbine

Steam

Water

Condenser

Combined cycle reference power plants

Multi Shaft

Single Shaft

60 Hz:

SCC6-1000F 1S

SCC6-4000F 1S

SCC6-6000G 1S

50 Hz:

SCC5-1000F 1S

SCC5-3000E 1S

SCC5-4000F 1S

SCC5-8000H 1S

50 Hz:

SSC5-2000E

SCC5-3000E 2x1

SCC5-4000F 2x1

60 Hz:

SCC6-4000F 2x1

SCC6-5000F 1x1 / 2x1

SCC6-6000G 2x1

SCC = Siemens Combined Cycle

SSC = Siemens Simple Cycle

Entire Power Plant � Turnkey• Power Island• Buildings and structures• Cranes• Cooling water systems• Electrical equipment• Power block controls• Fire fighting systems• Water treatment, raw / waste water treatment• Errection / Commissioning• Options

•Power Island

Combined Cycle Power Plants (single shaft)Arrangement of the different scopes of supply

BOT for Combined Cycle Power Plants

2. KKS

Purpose of KKSThe Identification System for Power Stations „KKS“ (Kra ftwerks Kennzeichen System)

serves to:

� identify plants

� sections of plants

� items of equipment

in any type of power station, according to:

� task

� type

� location

It is to be used by all engineering disciplines for

� planing

� licensing

� construction

� operation and maintenance

Requirements on KKS

Requirements on KKS:

� Uniform identification for all types of power station and any connected processes

� Sufficient capacity and detail for identification of all system, components and structures

� Consistent identification for planning, licensing, construction, operation, maintenance and wastemanagement

� Consideration of national and international standards

� Non-language-basewd coding to ensure international usability

� Application in computer processing

Types of identification codes

Process-related identification

� Process-related identification of systems and items of equipment according to their functions in mechanical, civil, electrical and control and instrumentation engineering

Location identification

� Identification of locations in structures, on floors and in rooms and also of fire areas and topographical stipulations (surface area grid)

Point of installation identification

� Identification of points of installation of electrical and control and Instrumentation devices in installation units (e.g. in cabinets, panels, consoles)

Process related identification

Process related identification

Process related identification

Process related identification

Location identification

Location identification

Location identification

Point of installation identification

The mounting space code. which is preceded by a fullstop symbol, specifies the exact installation locationby means of coordinates.

The coordinates are established in the followingmanner:The height of a mounting space, for instance, in acontrol cabinet, is divided into several identically sizedinstallation levels. Each installation level is identifiedwith a letter from top to bottom beginning with A. Thisletter specifies the first position in the coordinate. It ishighlighted in orange In the graphic.

If an installation level is divided horizontally, thesedivisions are likewise assigned letters, also beginningwith the letter A. This letter specifies the secondposition in the coordinate; it is highlighted in green inthe graphic.

The three characters identify the slot in an installationlevel and are numbered from left to right beginning with 001

Use of KKS in P&I Diagrams (P&ID)

Advanced use of KKS in P&IDs (for measurements)

-Temperature measurement-Indication-Registration-Alarming-Protection (trip) on >max (Z+)

(1)

(2)

(3)

Use of KKS in Function Charts (FUP)

BOT for Combined Cycle Power Plants

3. Siemens Documentation Structure

Overall documentation structure

Overall documentation structureOperating Manual (Overall Plant) - TO

The Operating Manual contains necessary information for the staff operating the power plant as overall plant.

Operating & Maintenance Documentation - TP

The Operating & Maintenance Documentation comprises technical documents and data required for the description of :

� the set-up and functioning of power plant components and systems

� the operation and maintenance.

Erection & Commissioning Manuals - TE

Compilation of requirements for the :

� Civil engineering

� Initial erection and

� Initial commissioning of power plants or power plant components.

The manuals are prepared for the customer according to Siemens Energy scope of supply and services, where appropriate, including the documents from contractors.

Overall documentation structure

Site Documentation – TS

The site documentation comprises :

� the proofs

� Protocols

� Certificates

� Etc.

arising during initial erection and initial commissioning in the form of quality records.

The structuring characteristics are the same as those for the operating & maintenance manuals.

Documentation sections

Operation & Maintenance manual identification

File Ident

10/20 .KKS… TP 8. 02+

KKS identifies volumes including possible redundancies

Volume comprises several files,

here: 3rd file, at least 1 more file follows

stands for mechanical systems and components

means "Operation and maintenance manual"

Manual Group Ident

T = Technical Customer Documentation

Volume Ident

Unit Ident

here: manual (volume) for identical components installed in Units 10and 20

Note:QC-Documentation may be issued as a "separate Volume" of the component manual Identification:10/20 . KKS . TP8 . QC . 03+Drawing packages may be issued as "separate volumes" (e.g.: "ready for construction" or "As-built").Identification:10/20 . KKS . TP8 . DWG . 03+ or10/20 . KKS . TP8 . ASB . 03+