weldfit push-in fittings. for use with weldtube to protect against damage from weld spatter. easy...

WeldFit Push-in Fittings

WeldFit Push-in Fittings

For use with WeldTube to protect against damage from weld spatter.

Easy tube insertion and removal Tube support for retention under high loads Recessed collet to prevent exposure of inner

tube under side loads Corrosion resistant nickel plated Sizes G1/8, G1/4, G3/8, G1/2

Inner tube 6, 8, 10, 12mm o/d For compressed air or water

WeldFit component parts

Recessed collet Multiple teeth ‘O’ Ring Tube support Body Sealing washer Temperature range

-300C to 700C Materials

Corrosion resistant nickel plated brass componentsNitrile ‘O’ RingPolyamide washer

Tube preparation

WeldFit push-in fittings

Tube preparation

Using a standard tube cutter, cut the complete tube end square at one of the markers.

Ensure that the tube end is clean and free from surface damage

900

Tube preparation

To prevent damage to the inner tube. Use the special stripping tool to cut the outer cover at the next marker

Tube preparation

Push open the tube grip Insert the cut to length tube and line up the next marker

with the blade Close the tube grip and rotate the stripper around the

circumference of the tube

Tube preparation

Push open the tube grip Insert the cut to length tube and line up the next marker

with the blade Close the tube grip and rotate the stripper around the

circumference of the tube

Tube preparation

Push open the tube grip Insert the cut to length tube and line up the next marker

with the blade Close the tube grip and rotate the stripper around the

circumference of the tube

Tube preparation

Next push the blade twist button, this turns the blade 900

Hold the button down and pull the stripper sideways to score the tube to the end

Peal off the outer covering

Tube preparation

Next push the blade twist button, this turns the blade 900

Hold the button down and pull the stripper sideways to score the tube to the end

Peal off the outer covering

Tube preparation

Next push the blade twist button, this turns the blade 900

Hold the button down and pull the stripper sideways to score the tube to the end

Peal off the outer covering

Tube preparation

Next push the blade twist button, this turns the blade 900

Hold the button down and pull the stripper sideways to score the tube to the end

Peal off the outer covering

Tube and fitting assembly

WeldFit push-in fittings

Tube assembly

Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.

Pull back on the tube to reinforce the collet teeth gripping action

The pressure can then be applied

Tube assembly

Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.

Pull back on the tube to reinforce the collet teeth gripping action

The pressure can then be applied

Tube assembly

Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.

Pull back on the tube to reinforce the collet teeth gripping action

The pressure can then be applied

Tube assembly

Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.

Pull back on the tube to reinforce the collet teeth gripping action

The pressure can then be applied

Tube assembly

Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.

Pull back on the tube to reinforce the collet teeth gripping action

The pressure can then be applied

Tube removal

WeldFit push-in fittings

Tube removal

Turn off and exhaust the pressure To remove the tube, push the collet in firmly and hold it

there. Pull the tube out and release the collet

Tube removal

Turn off and exhaust the pressure To remove the tube, push the collet in firmly and hold it

there. Pull the tube out and release the collet

Tube removal

Turn off and exhaust the pressure To remove the tube, push the collet in firmly and hold it

there. Pull the tube out and release the collet

Tube removal

Turn off and exhaust the pressure To remove the tube, push the collet in firmly and hold it

there. Pull the tube out and release the collet

The range

WeldFit push-in fittings

WeldFit Push-in Fittings

Included in the range: Straight adaptors Straight connectors Elbow connectors Tee connectors 900 Swivel adaptors 450 Swivel adaptors Banjo assembly range

WeldTube range

Tube range

Four tube sizes each with outer tube colours in a choice of black, blue, green or red.

Inner tube o/d 6,8,10 and 12 mm (4,6,7,9 mm id) Outer tube o/d 8,10,12.5,14.5 mm

Tube range

Minimum recommended bend radius 40, 50, 65 and 75 mm

End