zedge small floor wash zesrpfw- · 1.57" 2.48" 2.48" 0.157" 1.732" floor...
Post on 20-Jul-2020
4 Views
Preview:
TRANSCRIPT
1.57"
2.48
"
2.48"
0.157"
1.732"
Floor Wash ZESRPFW-Louver ZESRPLV-Bi-Emission ZESRPBE-
WARNINGRemote Class II electronic power supply will power the fixture with low voltage. DO NOT CONNECT FIXTURE WITH LINE VOLTAGE. FAILURE TO COMPLY WILL RESULT IN VOID OF WARRANTY. See Fixture Connection (page 2) for more information.To ensure a maximum efficient use of the product, read the instructions before proceeding installment.
This fixture must be installed by a licensed and qualified electrician. The installer must comply with NEC and local building codes when installing the fixture
Electrical current can cause painful shock, serious injury, or even death. Make sure you turn off the power supply, ground fixture(s), and make sure all electrical connections are correct and secured tightly
For use in IP66 installations.
Keep the label of the original packaging if any eventual future claims are needed
Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 09/2017 - Page 1 of 5
0.44 lbs
24VDC
+95°C
-13°F
3'
Table of Contents
Fixture Connection Fixture Installation Distribution of Light Maintenance Support
Pg.2Pg.3Pg.4Pg.5Pg.6
ZEDGE SmallZESRP-
COD. 2DI2CS00
Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 09/2017 - Page 2 of 5
24VDC
USE 18 AWG 2C SHIELDED WIRE
Zedge Small Sleeve1E3166
Fixture Connection
Fixture will be connected to 24 VDC output cable running through the fixture's installed sleeve or cavity with water tight connectors that are approved by code powered from a remote driver. DO NOT CONNECT THE FIXTURE TO LINE VOLTAGE. CONNECTING THE FIXTURE TO LINE VOLTAGE WILL DAMAGE THE FIXTURE AND VOID THE WARRANTY. Installer will be sure to only use 18 AWG shielded wiring to connect to the fixture. Be sure to connect the wires correctly on the connector and tightly securing it before connecting fixture. Provided below are the specs for fixture's driving power and dimming capabilities.
Power and Dimming Spec Chart
Power Supplies Type/Dimming TypeMax FixturesPer Driver Wattage
Input Voltage/Output Voltage
DELV-96-1-24-D
Electronic Low Voltage/Reverse Phase
40W
120-277VAC/24VDC
DELV-60-1-24-D 60W
DELV-40-1-24-D
96W
96W
DELX-90-1-24-1C-PWMElectronic PWM in NEMA3R Enclosure 90W
DELX-60-1-24-1C-PWM 60W
5
8
13
8
13
13
DMLV-120-1-24-DDMLV-60-1-24-DDMLV-40-1-24-D
DMLV-192-2-24-D
D010-96-1-24-D
DELX-270-3-24-3C-PWM
Electronic PWM in NEMA3R Enclosure
DELX-180-2-24-2C-PWM 26
39
Magnetic Low Voltage/Forward Phase
Electronic/0-10V
581326
40W60W96W
192W/2x96W
270W
180W
two rows of 13ea
120VAC/24VDC
120-277VAC/24VDC
120-277VAC/24VDC
DO NOT CONNECT FIXTURE TO MAIN VOLTAGE
Dimensions
2.50”W X 9.37”L x 1.89”D
3.00”W X 9.80”L x 3.00”D
10”W X 10”L 4”D
12”W X 12”L 4”D
2.67”W X 9.66”L 1.53”D
3.00”W X 9.80”L x 3.00”D2.25”W X 6.55”L x 2.55”D
2.00”W X 5.06”L x 2.14”D
12”W X 12”L 4”D
10”W X 10”L 4”D
2.50”W X 9.37”L x 1.89"D
4.06”W X 11.02”L x 2.20"D
DEDD-200-2-24-4C-DMXElectronic DMX in NEMA3R Enclosure 200W/ 2x100W
DEDD-100-1-24-4C-DMX 100W13
26two rows of 13ea
DEDD-200-2-24-4C-DALI
Electronic DALI in NEMA3R Enclosure
DEDD-100-1-24-4C-DALI 13
26two rows of 13ea 200W/ 2x100W
100W
120-277VAC/24VDC
120-277VAC/24VDC
10”W X 10”L 4”D
10”W X 10”L 4”D
12”W X 12”L 4”D
12”W X 12”L 4”D
Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 09/2017 - Page 3 of 5
Zedge Small Sleeve1E3166
1
2 Top View
Fixture Installation
1) Once the fixture's connection between the fixture and the driverhave been properly connected and tightly secured, locate thespring loaded mounting clip and press one side of the clip towardsthe mounted sleeve opening as you slide the whole fixture into themounted sleeve. The spring will compress together as the fixture ispushed through the insert.
2) As the fixture slides all the way into the sleeve insert, the springclip will open up and secure the fixture into its mounting position.The fixture will sit semi-flush within the sleeve as the face plate offixture sits flat on the mounted surface.
Zedge face plate
Distribution of Light
FLOOR WASHER
BI-EMISSION
LOUVER
Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 09/2017 - Page 4 of 4Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 -
(714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 09/2017 - Page 4 of 4
Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 09/2017 - Page 4 of 4Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 -
(714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 09/2017 - Page 4 of 4
Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 09/2017 - Page 4 of 5
Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 09/2017 - Page 5 of 5
Support
Any questions, problems, or comments you have please feel free to contact our Customer Service department
during our business hours Monday-Friday 8am-5pm via: Email: usaorders@targetti.com
Phone: (714) 513-1991
Visit our website: http://www.targetti.us
Maintenance
This fixture was designed and manufactured for a durable, long lasting use with minimum care. To ensure the
maximum lifespan of this product, we encourage our customer to provide a quality visual inspection of the fixture
every six months.If there are any visible sign of issues (i.e moisture or dust)
during the inspection, please clean any of the dust or moisture with a soft cloth and check to make sure that any of the fixtures are still operating normally. If there are any issues regarding the fixture please contact us as we will
assist the situation at hand.
top related