ANTI THEFT SYSTEM FOR BIKEUSING GSM

Group members Suchinmay MalarShreyash Kumbhojkar Vikas Malgaonkar

Adesh Neswankar

GUIDE PROF. MAHESH SUTAR

INTRODUCTION

An anti-theft system is any device or method used to prevent or detect the unauthorized appropriation of items considered valuable.

ABSTRACT

Security is primary concern everywhere and for everyone. Every person wants his home, industry, valuable belongings such as bikes, cars etc to be secured. Would you ever consider leaving thousands of rupees worth of your personal belongings in the street without protection? Well, that is what you do every time you park your car at the side of the road or anywhere else if you do not have a bike/car security alarm fitted to it. Most bikes/cars do not come with an effective protection system, and a determined thief is generally able to steal a car in a matter of seconds.

Proposed project act as an electronic protector + wireless reporter to owner if someone else tries to start the bike without a proper password. Also give siren for attention.

BLOCK DIAGRAM

Micro controller p89v51rd2

GSM Module

Relay driver circuit

Relay

Ignition system

Buzzer

2*16 character LCD

4*4 Matrix Keypad

Press Switch

IR sensors

GSM MODULE

What is GSM & GSM module? Why we used GSM Module? Its advantage Over RFID system.

MICROCONTROLLER P89V51RD2 What is MCU P89V51RD2?

The P89V51RD2 is an 80C51 microcontroller with 64 kB Flash and 1024 bytes of data RAM.

Features. 80C51 Central Processing Unit 5 V Operating voltage from 0 to 40 MHz 64 kB of on-chip Flash program memory with ISP and IAP Supports 12-clock (default) or 6-clock mode selection via software or ISP SPI (Serial Peripheral Interface) and enhanced UART PCA (Programmable Counter Array) with PWM and Capture/Compare functions Four 8-bit I/O ports with three high-current Port 1 pins (16 mA each). Three 16-bit timers/counters Programmable Watchdog timer (WDT) Eight interrupt sources with four priority levels Second DPTR register TTL- and CMOS-compatible logic levels Brown-out detection Low power modes

Power-down mode with external interrupt wake-up

Idle mode

SENSORS IR sensors

An infrared sensor is an electronic device that emits and/or detects infrared radiation in order to sense some aspect of its surroundings. Infrared sensors can measure the heat of an object, as well as detect motion.

Mini Press Button SwitchCOM-00097 RoHS in Fritzing Library 

in Eagle Library Description: We use these little

buttons on everything! These Miniature Single Pole Single Throw switches have a good click to them and are breadboard friendly. Perfect as a tactile reset switch. These buttons are rated up to 50mA. 

LCD DISPLAY

2*16 Char LCD Display Features

i. 5 x 8 dots with cursor

ii. Built-in controller (KS 0066 or Equivalent)

iii. + 5V power supply (Also available for + 3V)

iv. 1/16 duty cycle

v. B/L to be driven by pin 1, pin 2 or pin 15,

pin 16 or A.K (LED)

vi. N.V. optional for + 3V power supply

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

Vss

Vdd

Vo

RS

R/W

E

DB0

DB1

DB2

DB3

DB4

DB5

DB6

DB7

VLED-

VLED+

RS=0 for instruction, RS=1 for Data, RS is connected to P0.0

R/W=0 write, R/W=1 read

E=0 Disable, E=1 Enable, E is connected to P0.2

connected to P0.4

connected to P0.5

connected to P0.6

connected to P0.7

DATA

+5v

RELAY

A relay is an electrically operated switch. Many relays use an electromagnet to operate a switching

mechanism, but other operating principles are also used When a current flows through the coil, the resulting magnetic field

attracts an armature that is mechanically linked to a moving contact. The movement either makes or breaks a connection with a fixed

contact

3904

GND

Port pin 1K

Buzzer

NO

NCC

+5V

3904

GND

Port pin 1K

Buzzer

NO

NCC

Logic 0 N

F

230V

3904

GND

Port pin 1K

Buzzer

NO

NCC

Logic 0 N

F

230V

+5V

+5V Ignition system ON

Ignition system OFF

Idle

4x4 MATRIX KEYPAD

1 2 3 4

5 6 7 8

9 10 11 12

13 14 15 16

P2.0

P2.1

P2.2

P2.3

P2.4

P2.5

P2.6

P2.70

0

0

0

1

1

1

1

BUZZER

•It is a signaling device. •It beeps when user mismatch.

3904

GND

Port pin 1K

Buzzer

+5V

3904

GND

Port pin 1K

+5V Buzzer

Logic 0

+5V

BUZZER OFF

3904

GND

Port pin 1K

+5V Buzzer

Logic 1

+5V

BUZZER ON

POWER SUPPLY

Since we need +5v power supply to circuit we can use 9v/ 6v battery. Power supply available in Laboratory. Car/bike batteries

Along with following voltage regulator circuit-

VOLTAGE REGULATOR IC 7805

IC 7805 is used to give a +5V dc supply in the power supply. The 7805 series of devices is a family of self-contained fixed linear voltage regulator integrated circuit .The 7805 is a very popular choice for many electronic circuits that require a regulated power supply, due to their ease of use and relative cheapness. The 7805 has a 5 volt output as it is dependent on the last two-digit number.7805 ICs have 3 terminals. 7805 ICs have built-in protection against a circuit drawing too much power. 7805 ICs do not require any additional components to provide a constant, regulated source of power, making them easy to use, as well as economical, and also efficient uses of circuit board real estate

Features: • Output Current up to 1A • Output Voltages of 5, 6, 8, 9, 10, 12, 15, 18, 24V • Thermal Overload Protection • Short Circuit Protection

SOFTWARE1. Keil compiler 2. Eagle 5.0

WORKING ON THE PROJECT

All the theoretical work was done including circuit diagram, working and programming section now its time to work practically on project.

STAGE 1: components were finalized and bought

The components were bought from Visha Electronics .The components that are used in this project are:-

SR NO. COMPONENT QUANTITY

1. Keypad section:

Tick-Tack Switches 16

2. Buzzer section:

1K 2

5V buzzer 1

BC8050 1

3. GSM module 14. 2x16 Char LCD 1

1.5K 1

16 pin Female burg strip 1

5. Microcontroller section:

10uF 1

10k 1

11.0592MHz crystal 1

33pF 2

10K Resistor network 1

P89V51RD2 1

6. Power supply section:

DC jack 1

Slide switch 1

3mm LED 1

10K 1

IC- LM7805 1

100uF 1

10uF 1

0.1uF 1

Burg-strip-2pin 2

7. Relay section:

1K 2

Relay 1

C8050 1

1N4007 1

8. Adapter 29. IR Section module 110. Press switch 111. Pcb 212. Printing & etching -13 wires 10

STAGE 2- PCB layoutPCB layout was done using EAGLE layout editor

software.

Track layout

Component layout

Component + track layout

STAGE 3 :

After printing ,etching and drilling work; was PCB was ready…..

STAGE 4 : project was ready after mounting and soldering of

components.

STAGE 5:

Program was ready after successful compilation. Program was compiled using Keil compiler software.Program was successfully burned in to MCU.

Some screenshots of compiling software….

CIRCUIT DIAGRAM

WORKING

In order to start the ignition system user will be asked to provide the pre-stored password.

If he enters wrong password 2-3 times, the security system sends the message to user’s mobile using GSM module in first time only.

System will give the fake response of re-entered password to thief up to 3 times. In that time user can come & catch the thief.

Also user can control system suing mobile phone by sending text message.

Also if theft will try to move bike without starting ignition system, then IR sensors connected near back wheel can track motion of wheel & will give a siren.

Also we have situated the LCD & keypad system near to speedometer and it is covered by glass envelope Press switch is attached below the glass envelope.

If thief tries to damage the system or to remove glass cover then switch gets open & system will sound the buzzer.

System reset button is also there. We hide the button at such place that user will only know the position of it.

We can ON/OFF the system only when we require.

ADVANTAGES

Prevent your bike from being stolen. Smart alert for system protection. Lower rates for manufacturing system. Small size and light weight.

FUTURE ASPECTS

Vehicle tracking by GPS if system fails.

We can use different types of locks like face reorganization, fingerprint reader.

Mechanical and electronic immobilizer.

System can be made much portable using SMDS and integrated circuits.

CONCLUSION

BIBLIOGRAPHY

Let us c- Prof. Vasant kanitkar. Electronics Instrumentation by H.S.Kalshi, Tata Mc

Grawhill. Programming in embedded ‘c’ By David E. Simon, Pearson

Education. www.google.co.in www.datasheet4u.com www.Alldatasheet.com

 

THANK YOU

PLEASE FEEL FREE TO ASK ANY QUESTIONS

Group members:o Suchinmay Malaro Shreyash Kumbhojkaro Vikas Malgaonkaro Adesh Neswankar