“green” moisture control & adhesive isolation membrane€¦ · dritac 7100 is a...

3
TECHNICAL DATA SHEET 7100 ECO-DRIBLOC “Green” Moisture Control & Adhesive Isolation Membrane OWNED & OPERATED IN USA ATTRIBUTES • Reduces Moisture Vapor Transmission • Zero Solvents • Easy Clean Up When Wet • Helps Contribute to LEED Credits • Carpet Tile • VCT • Cork Tile • Luxury Vinyl Tile/Plank FLOORING TYPES • Adhesive Isolation Membrane • Fast Drying - 3 Hours • Same Day Floor Installation • Roller Applied • Fiberglass Back Sheet Vinyl • Cork/Rubber/Foam Underlayments • Laminate • Floating Floors Green Label Plus, Indoor Air Quality (IAQ) Certified! For maximum protection, use with DriTac 5900 MegaBond or DriTac 5700 StrongBond - applied with trowel or 3/8”nap roller: • 1 Coat = 15 lbs., per the ASTM F1869 Calcium Chloride Method Test - 98% RH, per the ASTM F2170 Relative Humidity - 3-hour dry time For use with other DriTac Resilient Water-Based Flooring Adhesives - DriTac 5500 PowerBond, DriTac 5200 BigBond, DriTac 6200 • 1 Coat = 12 lbs., per the ASTM F1869 Calcium Chloride Method Test - 85% RH, per the ASTM F2170 Relative Humidity - 3-hour dry time • 2 Coat = 15 lbs., per the ASTM F1869 Calcium Chloride Method Test - 90% RH, per the ASTM F2710 Relative Humidity - 24-hour dry time DriTac 7100 is a single-component, 2-in-1, fast drying concrete moisture control system and adhesive isolation membrane that allows installers to apply a moisture mitigation system and install their resilient floor the same day. Available Container Size: 4-Gallon Pail

Upload: others

Post on 24-Sep-2020

1 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: “Green” Moisture Control & Adhesive Isolation Membrane€¦ · DriTac 7100 is a single-component, 2-in-1, fast drying concrete moisture control system and adhesive isolation membrane

TECHNICAL DATA SHEET

7100ECO-DRIBLOC“Green” Moisture Control& Adhesive IsolationMembrane

OWNED & OPERATEDIN USA

ATTRIBUTES• Reduces Moisture Vapor Transmission

• Zero Solvents

• Easy Clean Up When Wet

• Helps Contribute to LEED Credits

• Carpet Tile

• VCT

• Cork Tile

• Luxury Vinyl Tile/Plank

FLOORING TYPES

• Adhesive Isolation Membrane

• Fast Drying - 3 Hours

• Same Day Floor Installation

• Roller Applied

• Fiberglass Back Sheet Vinyl

• Cork/Rubber/Foam Underlayments

• Laminate

• Floating Floors

Green Label Plus, Indoor Air Quality (IAQ) Certified!®

For maximum protection, use with DriTac 5900 MegaBond or DriTac 5700 StrongBond - applied with trowel or 3/8”nap roller:

• 1 Coat = 15 lbs., per the ASTM F1869 Calcium Chloride Method Test - 98% RH, per the ASTM F2170 Relative Humidity - 3-hour dry time

For use with other DriTac Resilient Water-Based Flooring Adhesives - DriTac 5500 PowerBond, DriTac 5200 BigBond, DriTac 6200

• 1 Coat = 12 lbs., per the ASTM F1869 Calcium Chloride Method Test - 85% RH, per the ASTM F2170 Relative Humidity - 3-hour dry time • 2 Coat = 15 lbs., per the ASTM F1869 Calcium Chloride Method Test - 90% RH, per the ASTM F2710 Relative Humidity - 24-hour dry time

DriTac 7100 is a single-component, 2-in-1, fast drying concrete moisture control system and adhesive isolation membrane that allows installers to apply a moisture mitigation system and install their resilient floor the same day.

Available Container Size: 4-Gallon Pail

Page 2: “Green” Moisture Control & Adhesive Isolation Membrane€¦ · DriTac 7100 is a single-component, 2-in-1, fast drying concrete moisture control system and adhesive isolation membrane

TECHNICAL DATA SHEET

INSTRUCTIONS

Read all information before installation. Please contact DriTac Flooring Products at (973) 614-9000 with questions.

PROPERTIES AND USAGE OF ECO-DRIBLOC Eco-DriBloc is a “green”, single-component, latex based product that reduces moisture vapor transmission from concrete substrates and protects the floor covering installed. Eco-DriBloc can also serve to encapsulate and isolate old adhesive residue. Eco-DriBloc is for use under most types of floor coverings, including LVT/LVP, fiberglass back sheet vinyl, carpet tile, VCT, cork tile, cork/rubber/foam underlayments, laminate flooring and all other floating floors. Eco-DriBloc can be used over porous concrete to help reduce penetration of the adhesive and also reduces dusting of the concrete, which will result in increased spread rates and stronger bond with floor covering adhesives. Eco-DriBloc is compatible with all DriTac water-based adhesives. Consult DriTac Technical Services at (973) 614-9000 for floor coverings not listed and adhesives that are not water-based.

RECOMMENDED SUBSTRATES

When Used as an Isolation Membrane:

• Plywood• Concrete

When Used as Moisture Control System:

• New (concrete must be 60-days old) and existing concrete, above and on grade• Lightweight Concrete and Gypcrete, above-grade only

MOISTURE CONTROL

Concrete Moisture Control:• 1 Coat = 12 lbs per the ASTM F 1869 Calcium Chloride Test Method and 85% RH per the ASTM 2170 Relative Humidity Test.• 2 Coats = 15 lbs per the ASTM F 1869 Calcium Chloride Test Method and 90% RH per the ASTM 2170 Relative Humidity Test.

SURFACE PREPARATION

All substrates must be clean and free of dust, oil, grease, paint, curing agents, concrete sealers or any other substances that may prevent or reduce the sealers ability to adhere to the substrate. Use over carpet adhesive residue and cutback adhesive residue that have been scraped to the concrete is allowed. All substrates must be flat to industry standards, 1/8” in 6 feet or 3/16” in 10 feet. Always install Eco-DriBloc first, then apply patching compounds over top as directed. Drying times will vary based on porosity of the substrate and jobsite conditions. Adhesives and patching compounds will typically require extended drying times when applied over Eco-DriBloc. Substrate must be visibly dry without a history of moisture failures.

APPLICATION

Apply using a 1/4” or 3/8” roller. Apply Eco-DriBloc in a smooth, even coat. Avoid leaving puddles. Roll Eco-DriBloc in a north-south, then east-west direction, to ensure proper coverage. Do not pour directly on the concrete. Use a roller or paint tray. Allow 3 hours dry time prior to applying second coat of Eco-DriBloc or flooring. If a second coat is desired, apply in same direction as first coat and allow sealer to dry for 24 hours prior to installation of flooring. Adhesives and patching compounds may require extended drying times when applied over Eco-DriBloc.

COVERAGE

• 175 - 225 sq. ft per gallon - depending on size of the nap roller used, substrate porosity and smoothness of the substrate.

DRYING TIME

• Single coat 3 hours to install flooring• Second coat requires 24 hours to install flooring

LIMITATIONS

Eco-DriBloc is not an equal replacement for high performance, epoxy based moisture reduction barrier. Eco-DriBloc can be ap-plied over carpet adhesive residue and asphalt cutback adhesive residue as long as the adhesive ridges and raised residue have been completely removed from the subfloor with only minor stains remaining. All soft, loose and raised residue must be removed before encapsulation begins. All adhesive must be hard, firm and well bonded. When installing resilient flooring and carpet tiles with nonporous backings, do not use wet lay adhesives or the wet lay method. Use the total flash off method only, when utilizing pressure sensitive adhesives. Radiant heated subfloors should be turned off 24 hours prior to and during installation to prevent premature curing.

Page 3: “Green” Moisture Control & Adhesive Isolation Membrane€¦ · DriTac 7100 is a single-component, 2-in-1, fast drying concrete moisture control system and adhesive isolation membrane

TECHNICAL DATA SHEET

CLEAN UP

Wet Eco-DriBloc can be removed with a damp cloth. Dry Eco-DriBloc can be removed with mineral spirits or a safe solvent. Hands and tools may be cleaned with “waterless hand cleanser” available at hardware and auto supply stores.

VENTILATION

Installers should provide adequate cross-ventilation during and for 24 hours after installation.

PRECAUTIONS

V.O.C. 0 grams/liter. Avoid eye contact. In case of eye contact, flush eye with clean water for fifteen minutes. If irritation persists, get medical attention. Use with adequate ventilation. Keep out of reach of children.

FIRST AID

In case of eye contact, flush thoroughly with water for at least 15 minutes. SEEK IMMEDIATE MEDICAL ATTENTION. In case of skin contact, wash affected areas with soap and water. If irritation persists, SEEM MEDICAL ATTENTION. Remove and wash all contaminated clothing. If inhalation causes physical discomfort, remove to fresh air. If discomfort persists, SEEK MEDICAL ATTENTION.

INSTALLER RESPONSIBILITY

These directions are general guidelines for flooring installations. It is the responsibility of the installer to determine acceptability of subfloor conditions. Installation must also be in accordance with flooring manufacturer’s recommendations. For any installation not herein recommended, contact DriTac Flooring Products before proceeding.

WARRANTY

This product is warranted to be free of manufacturing defects. If a manufacturing defect is found within one year from the date of purchase, such defective product shall be replaced. No warranty either expressed or implied is made regarding the performance of this product since conditions under which these goods are transported, stored, used or applied are beyond our control. This warranty is made in lieu of all other warranties either expressed or implied and the seller shall not be responsible for consequential, incidental, special or other damages no matter what the cause.GHS label elements: Not Applicable. Signal word: Not Applicable. Hazard statements: Causes skin irritation. Causes serious eye irritation. May cause an allergic skin reaction. May cause respiratory irritation. Precautionary statements: Wear protective gloves: butyl rubber, Ethyl vinyl alcohol laminate (EVAL), nitrile rubber, neoprene rubber. Wear eye and face protection. Wear protective clothing. Avoid breathing vapor. Avoid release to the environment. Wash hands thoroughly after handling. Collect spillage.