auto cad_chapter2 draw and modify tools
TRANSCRIPT
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
1/21
Auto CAD
BY: Engr. Jeffrey C. Odtohan
EcE Department
P.U.P. Sta. Mesa, Manila
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
2/21
Chapter 2:
Draw and Modify Tools
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
3/21
The Draw Tools
To start the command Left-clickon the
command in the 2D Draw control panel.
It is good to read the notes in the Command
line in the command window.
Use the Buttons on the Status Barto
smoothen the use of the commands.
To familiarize the draw tools, a sets of
exercises will be given.
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
4/21
Exercise 1
Instructions: You can use the following commands; line, polyline
and dimension command.
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
5/21
Exercise 2
Instructions: You can use the following commands; line, polyline
and dimension command.
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
6/21
Exercise 3
Instructions: You can use the following commands; line, circle and
dimension command.
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
7/21
Exercise 4
Instructions: You can use the following commands; line, polyline
and dimension command.
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
8/21
Exercise 5
Instructions: You can use the following commands; line, polyline
and dimension command.
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
9/21
Exercise 6
Instructions: You can use the following commands; circle and
dimension command.
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
10/21
Exercise 7
Instructions: You can use the following commands; polyline and
dimension command.
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
11/21
Exercise 8
Instructions: You can use the following commands; polyline and
dimension command.
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
12/21
Exercise 9
Instructions: You can use the following commands; line, polyline,
arc, and dimension command.
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
13/21
Exercise 10
Instructions: You can use the following commands; polygon, circle
and text command.
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
14/21
The Modify Tools
To start the command Left-clickon the
command in the 2D Draw control panel.
It is good to read the notes in the Command
line in the command window.
Use the Buttons on the Status Barto
smoothen the use of the commands.
To familiarize the draw tools, a sets of
exercises will be given.
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
15/21
Exercise 11
Instructions: You can use the following commands; line, polyline,copy and dimension command. Complete the figure by using
chamfer and fillet command. Then after use offset inside and
outside by 10.
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
16/21
Exercise 12
Instructions:
1. Draw the 1st figure using line or polyline command. Please
take note of the dimension.
2. Draw the 2nd figure using mirrorcommand.
3. Move the figure in the location (100,100) with respect to its
reference point indicated by the red arrow. Then check the location.
(100,100)
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
17/21
Exercise 13
Instructions:
4. Draw the below figures using copy command.5. Erase all the figures copied except to the original figure.
6. Draw again the below figures using the array command.
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
18/21
Exercise 14 Instructions:
7. Draw the below figures using circle command.8. Move the circle in location (500,100) with respect to its center.
9. Using the offset command, draw the figure below. Outer circle
has an offset of10 while inner circle has an offset of5.
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
19/21
Exercise 15
Instructions:
10. Draw a line with a dimension of 200 across the center, Refer tothe drawing below.
11. Use the trim command to draw the next figure below.
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
20/21
Exercise 16
Instructions:12. Use the extend command to draw the next figure below.
-
7/27/2019 Auto CAD_Chapter2 Draw and Modify Tools
21/21
Exercise 17 Instructions:
13. Use the array command.14. Set to polar with center (700,100).