autocad 2010 tutorial 1

8/3/2019 AutoCad 2010 Tutorial 1

1/21

AutoCad 2010 Tutorial 1 - Status Bar

This AutoCAD 2010 tutorial has two parts, the initial part will be instructions for the drawingaids and the second part is for the other icons located in the status bar.

CoordinatesThe X and Y (and Z) location of the crosshairs is shown in the coordinate area at the bottomleft of the application window.Snap Mode

This mode restricts the crosshairs movement to a particular X, Y spacing.Grid Display

The grid display controls a grids visibility and proportions.Ortho Mode [F8]An easy method to draw or move objects up, down or sideways in only 90 degree

increments is to use ortho mode.Polar Tracking

Pre-set rotation angles in this drawing aid helps decrease the amount of times you enternumbers.Object Snap

Object snap is a tool locates markers at predetermined locations on objects. While using acommand, object snap permits you to select precise points on existing objects.
http://www.auto-cad-tutorial.com/snap-command.htmlhttp://www.auto-cad-tutorial.com/grid-command.htmlhttp://www.auto-cad-tutorial.com/polar-tracking-command.htmlhttp://www.auto-cad-tutorial.com/object-snap.htmlhttp://www.auto-cad-tutorial.com/object-snap.htmlhttp://www.auto-cad-tutorial.com/polar-tracking-command.htmlhttp://www.auto-cad-tutorial.com/grid-command.htmlhttp://www.auto-cad-tutorial.com/snap-command.html


2/21

Object Snap Tracking

Using coordinates obtained from two different points, it creates a brand new point that is inline and at specific angles to the references points. It is most effectively used in conjunction

with polar tracking and object snaps.Allow/Disallow Dynamic UCS [F6]When dynamic USC is turned on it is easier to draw objects on the face of a 3D solid.Dynamic Input [F12]Dynamic Input is an active heads up display that mimics the command line. If the command

line options are accessible at the cursor, a small down arrow will appear at the end of thecursor prompt. Those options can be made visible by pressing the arrow key on the key

board down.Show/Hide LineweightThe lineweight assigned to an object can be made visible or not with this tool button. Rightclicking the icon and choosing "Settings..." will allow you to change the command options.

The following section of the AutoCAD 2010 Tutorial touches on a few other tools on your

status bar.Quick Properties

When turned on, a small properties box appears when you choose an object. It permits you

to manage some of the objects properties.Model / PaperActivates either Model space or Paper space.

Quick View Layouts
http://www.auto-cad-tutorial.com/object-snap-tracking.htmlhttp://www.auto-cad-tutorial.com/quick-properties-palette.htmlhttp://www.auto-cad-tutorial.com/quick-view-layouts.htmlhttp://www.auto-cad-tutorial.com/quick-view-layouts.htmlhttp://www.auto-cad-tutorial.com/quick-properties-palette.htmlhttp://www.auto-cad-tutorial.com/object-snap-tracking.html


3/21

The thumbnails for the open drawings are displayed, any drawing can be made active by

clicking on its thumbnail.Quick View DrawingQuick View Drawings displays all the drawings you have open. You can switch betweendrawings quickly by selecting the thumbnails.

Pan Command

Panning is usually lumped together with the zoom command, it doesnt change the size ofan object only the location of the window you are viewing your drawing through.

Zoom Command

Zooming doesnt change the size of the objects in your drawing it only changes how theobjects are being viewed.

AutoCAD 2010 Tutorial 2 - Draw Panel Guide

The goal with this AutoCAD 2010 Tutorial will be to demonstrate how to successfully draw

objects. We are going to concentrate on fundamental 2D components, which are the toolscontained in the Draw Panel.
http://www.auto-cad-tutorial.com/pancommand.htmlhttp://www.auto-cad-tutorial.com/zoom-command.htmlhttp://www.auto-cad-tutorial.com/zoom-command.htmlhttp://www.auto-cad-tutorial.com/pancommand.html


4/21

Line CommandA line is the shortest distance in between two coordinate points and is also one of the most

fundamental drawing objects.Arc CommandThe arc command creates curved line segments or just part of a circle.Pline Command (Polyline)A specialized object created by lines and/or arcs which are connected together to create oneobject.Circle CommandA circle has a radius (measured from the centre towards the edge) and also a diameter (the

length across the circle thru the centre). This command builds a circle in a counter clockwiserotation beginning and ending in the 3:00 oclock position.Rectangle CommandRectangles may be created using lines, but that approach isn't going to draw a rectangle as

effectively as a dedicated command.Ellipse CommandAn ellipse is a lot like a flattened circle which is shaped with major (bigger) and minor(smaller) axis.
http://www.auto-cad-tutorial.com/line-command.htmlhttp://www.auto-cad-tutorial.com/line-command.htmlhttp://www.auto-cad-tutorial.com/arc-command.htmlhttp://www.auto-cad-tutorial.com/arc-command.htmlhttp://www.auto-cad-tutorial.com/pline-command.htmlhttp://www.auto-cad-tutorial.com/pline-command.htmlhttp://www.auto-cad-tutorial.com/circle-command.htmlhttp://www.auto-cad-tutorial.com/circle-command.htmlhttp://www.auto-cad-tutorial.com/rectangle-command.htmlhttp://www.auto-cad-tutorial.com/rectangle-command.htmlhttp://www.auto-cad-tutorial.com/ellipse-command.htmlhttp://www.auto-cad-tutorial.com/ellipse-command.htmlhttp://www.auto-cad-tutorial.com/ellipse-command.htmlhttp://www.auto-cad-tutorial.com/rectangle-command.htmlhttp://www.auto-cad-tutorial.com/circle-command.htmlhttp://www.auto-cad-tutorial.com/pline-command.htmlhttp://www.auto-cad-tutorial.com/arc-command.htmlhttp://www.auto-cad-tutorial.com/line-command.html


5/21

Hatch CommandCross hatching is when you fill an area in a drawing with a pattern. Using the appropriatehatch pattern makes the drawings easier to understand.Spline CommandA curled line can be made with this command and feature control points for editing thebends.Polygon CommandA polygon is drawn similar to a closed polylines. The explode command is often used totransform it into independent line objects.Xline Command (Construction Line)This is a line type without endpoints. The ends of the lines are infinite and always extend to

the edges of your monitor no matter how you zoom. Since you'll find no ends, the onlyobject snap setting that will do the trick is the midpoint setting.Ray CommandThe Ray Command inserts a line containing a particular starting point and stretchesinfinitely, like the Xline command but only in one direction.Point Command and DDPTYPEA node is not just a single pixel object, there a many different styles that can be used tomark a specific location in a drawing.Divide CommandReference points with equal spacing can be made on various types of objects by using the

divide command.Measure CommandThis command lets you locate points at specific distances along the length various objects.

It doesn't actually measure your objects length, instead it defines the segment length inbetween two points.
http://www.auto-cad-tutorial.com/hatch-command.htmlhttp://www.auto-cad-tutorial.com/hatch-command.htmlhttp://www.auto-cad-tutorial.com/spline-command.htmlhttp://www.auto-cad-tutorial.com/spline-command.htmlhttp://www.auto-cad-tutorial.com/polygon-command.htmlhttp://www.auto-cad-tutorial.com/polygon-command.htmlhttp://www.auto-cad-tutorial.com/xline-command.htmlhttp://www.auto-cad-tutorial.com/xline-command.htmlhttp://www.auto-cad-tutorial.com/ray-command.htmlhttp://www.auto-cad-tutorial.com/ray-command.htmlhttp://www.auto-cad-tutorial.com/point-command.htmlhttp://www.auto-cad-tutorial.com/point-command.htmlhttp://www.auto-cad-tutorial.com/divide-command.htmlhttp://www.auto-cad-tutorial.com/divide-command.htmlhttp://www.auto-cad-tutorial.com/measure-command.htmlhttp://www.auto-cad-tutorial.com/measure-command.htmlhttp://www.auto-cad-tutorial.com/measure-command.htmlhttp://www.auto-cad-tutorial.com/divide-command.htmlhttp://www.auto-cad-tutorial.com/point-command.htmlhttp://www.auto-cad-tutorial.com/ray-command.htmlhttp://www.auto-cad-tutorial.com/xline-command.htmlhttp://www.auto-cad-tutorial.com/polygon-command.htmlhttp://www.auto-cad-tutorial.com/spline-command.htmlhttp://www.auto-cad-tutorial.com/hatch-command.html


6/21

AutoCAD 2010 Tutorial 3 - Easy Instructions forthe Modify Panel.

The following AutoCAD 2010 Tutorial will assist you in discovering AutoCAD by plainly

outlining the Modify Panel. In this AutoCAD Tutorial I will demonstrate the best way tochange objects with or without commands.

Move Command

It is typical to move a single or group of objects from one spot to another because of design

modifications or drawing blunders.

Copy Command

Rather than redrawing the same objects it is faster to draw it one time and create copies in

different places.

Rotate Command

Sometimes a change an objects alignment within a drawing is needed. The rotate commandvaries the angle of an object in relation to a base point.

Stretch Command
http://www.auto-cad-tutorial.com/move-command.htmlhttp://www.auto-cad-tutorial.com/copy-command.htmlhttp://www.auto-cad-tutorial.com/rotate-command.htmlhttp://www.auto-cad-tutorial.com/stretch-command.htmlhttp://www.auto-cad-tutorial.com/stretch-command.htmlhttp://www.auto-cad-tutorial.com/rotate-command.htmlhttp://www.auto-cad-tutorial.com/copy-command.htmlhttp://www.auto-cad-tutorial.com/move-command.html


7/21

Objects can be re-sized by simply dragging them. The stretch command may be applied tomodify a single object or multiple objects.

Scale Command

When parts of a drawing or object need to be proportionately bigger or proportionately

smaller in sized, it can be altered with this command.

Offset Command

The offset command is put into use to create a copy of the object parallel to the first at a

specified distance away from the first.

Mirror Command

In a few steps a mirror image of an object is created.

Trim Command

Sometimes designs dont look like they are supposed to until after they're modified. To getto the final product cut out bits of the objects.

Extend Command

The object end that is extended is closest to the point the object was selected from. Itextendes until it intersects the selected boundary edge.

Erase Command

When you learn AutoCAD, a natural result in your drawing process is to fix errors.

Explode Command

A group of object or a compound object can be reduced into its individual components, atthe click of a button.
http://www.auto-cad-tutorial.com/scale-command.htmlhttp://www.auto-cad-tutorial.com/offset-command.htmlhttp://www.auto-cad-tutorial.com/mirror-command.htmlhttp://www.auto-cad-tutorial.com/trim-command.htmlhttp://www.auto-cad-tutorial.com/extend-command.htmlhttp://www.auto-cad-tutorial.com/erase-command.htmlhttp://www.auto-cad-tutorial.com/explode-command.htmlhttp://www.auto-cad-tutorial.com/explode-command.htmlhttp://www.auto-cad-tutorial.com/erase-command.htmlhttp://www.auto-cad-tutorial.com/extend-command.htmlhttp://www.auto-cad-tutorial.com/trim-command.htmlhttp://www.auto-cad-tutorial.com/mirror-command.htmlhttp://www.auto-cad-tutorial.com/offset-command.htmlhttp://www.auto-cad-tutorial.com/scale-command.html


8/21

Array Command

A rectangular or circular pattern is made from copies of an object.

Fillet Command

Two sharp corners are connected with a rounded corner using the fillet command.

Chamfer Command

The chamfer command connects two sharp corners with a bevelled line.

Lengthen Command

The end that will be lengthened is the one nearest to the location where the object was

chosen.

Break Command

Breaking an object is to create a separation between its two haves.

Grips

Making use of grips happens to be an alternative approach to editing objects, this AutoCAD

2010 Tutorial explains how.

AutoCAD 2010 Tutorial 4 - How To Navigate theLayers Panel
http://www.auto-cad-tutorial.com/array-command.htmlhttp://www.auto-cad-tutorial.com/fillet-command.htmlhttp://www.auto-cad-tutorial.com/chamfer-command.htmlhttp://www.auto-cad-tutorial.com/lengthen-command.htmlhttp://www.auto-cad-tutorial.com/break-command.htmlhttp://www.auto-cad-tutorial.com/grips.htmlhttp://www.auto-cad-tutorial.com/grips.htmlhttp://www.auto-cad-tutorial.com/break-command.htmlhttp://www.auto-cad-tutorial.com/lengthen-command.htmlhttp://www.auto-cad-tutorial.com/chamfer-command.htmlhttp://www.auto-cad-tutorial.com/fillet-command.htmlhttp://www.auto-cad-tutorial.com/array-command.html


9/21

Inside this AutoCAD 2010 Tutorial we'll focus on each command positioned in the Layers

panel. The AutoCAD key board commands, which are normally called Command prompts,

are in bracket beside the command name.

The How To: tips are comparable for every command. The more comprehensive commandspossess a specific web page to visit, while the basic commands are presented in this

AutoCAD 2010 Tutorial page.

Every command has the same location:

Ribbon > Home tab > Layers panel >

Layer Command (Layer Properties)

Here you will get total control of all layer properties.

Make Objects Layer Current [laymcur]

When an object has been selected its layer becomes current layer.

Tool Button: Change to Current layer

Layer Match [laymch]The properties of one layer are applied to another.

Tool Button: Match Layer
http://www.auto-cad-tutorial.com/layer-command.htmlhttp://www.auto-cad-tutorial.com/layer-command.html


10/21

Layer Previous [layerp]The AutoCAD application keeps a log that details all of the changes made to the layersettings. There are some changes this command can't undo like: layer name changes, layer

purges or recently created layers.

Tool Button: Previous

Layer Isolate

It is often easier to look through your drawing when layers are invisible, this commandmakes all the layers disappear except for the one selected.

Layer States Manager [layerstate]A dialog box is displayed, it enables you to set up, rename, change, and erase saved layer

states.

Tool Button: Layer State Manager

Layer Unisolate [layuniso]This command re-establishes the layers just before they were hidden or locked with the

Layer Isolate command.

Tool Button: Unisolate

Layer Freeze

When a layer is frozen the object on it are invisible, as a result regenerating the drawing is

faster.

Layer Off

Once you switch off a layer the objects will not be seen in the drawing, they will alsoregenerate but won't print.

Turn All Layers On [layon]Layers that are currently off, come back on.

Tool Button: Turn All Layers On
http://www.auto-cad-tutorial.com/layer-isolate.htmlhttp://www.auto-cad-tutorial.com/layer-freeze.htmlhttp://www.auto-cad-tutorial.com/layer-off.htmlhttp://www.auto-cad-tutorial.com/layer-off.htmlhttp://www.auto-cad-tutorial.com/layer-freeze.htmlhttp://www.auto-cad-tutorial.com/layer-isolate.html


11/21

Thaw All Layers [laythw]This thaws all the currently frozen layers.

Tool Button: Thaw

All Layers Lock [laylck]Locking layers In a busy drawing will make editing easier.

Tool Button: Lock

Unlock [layulk]

Using this command will unlock layers simply by choosing an object on the locked layer.

Tool Button: Unlock

Change to Current Layer [laycur]When an object is selected its layer will become current.

Tool Button: Change Objects to Current Layer

Layer Walk [laywalk]

You can cycle through the layers shown in a dialog box and get list of the object on eachindividual layer.

Tool Button: Layer Walk

Isolate Current ViewportThis command is used for viewports. It freezes the selected layer in all viewports except for

the active viewport.

Tool Button: Isolate Current Viewport

Layer MergeThis is a good tool to use when trying to quickly maintain your layers. You can move all theobject from one layer to another and delete it all in one shot.


12/21

Tool Button: Merge

Layer Delete [laydel]

Try this to purge a layer from a drawing after you have erased all the object from it.

Tool Button: Layer Delete

All the commands listed in this AutoCAD 2010 Tutorial allow you to control the visibility of

the information in your drawing.

AutoCAD 2010 Tutorial 5 - Top 10 Ways to AddNotes to your Drawings

Studying AutoCAD is straightforward whenever youve got a great AutoCAD 2010 Tutorial.This will clarify all of the ways youll be able to put notes and comments onto drawings. A

handy location that all these tools are found on is called the annotation panel.


13/21

In AutoCAD you'll find two techniques for generating text:

Single Line Text

Using a single text line, also known as a text string, is the first way. It is a single objectcreated from one line of text.

Multiline Text

The second way is to choose an in-place text editor for making paragraphs, this approachcan also be identified as multiline text.

Linear Dimension Command

One of the most frequently applied dimensions to show the distance between two points islinear dimensions.

Aligned Dimension Command

The difference between aligned and linear dimensioning is what is actually measured.

Aligned calculates the exact distance within two points, rather than only a horizontal or onlya vertical distance.

Angular Dimension Command
http://www.auto-cad-tutorial.com/single-line-text.htmlhttp://www.auto-cad-tutorial.com/multiline-text-command.htmlhttp://www.auto-cad-tutorial.com/linear-dimension-command.htmlhttp://www.auto-cad-tutorial.com/aligned-dimension-command.htmlhttp://www.auto-cad-tutorial.com/angular-dimension-command.htmlhttp://www.auto-cad-tutorial.com/angular-dimension-command.htmlhttp://www.auto-cad-tutorial.com/aligned-dimension-command.htmlhttp://www.auto-cad-tutorial.com/linear-dimension-command.htmlhttp://www.auto-cad-tutorial.com/multiline-text-command.htmlhttp://www.auto-cad-tutorial.com/single-line-text.html


14/21

The dimension line indicates the size of the angle between two points measured along thepath of the angle.

Arc Length Dimension

The arc length is annotated with a parallel dimensioned line.

Diameter and Radius Dimension Command

There are two choices when dimensioning a circle. You can show a dimension line for eitherthe radius or diameter.

Jog Line

When a jog is used in an object it will measure smaller compared to what the dimension linesays.

Multileader Command

Leaders point out specific parts of the drawing to give special instructions about the design.They can be built with straight line or smooth curved lines.

Table Command

Many AutoCAD software releases ago, tables had to be created by lines. This AutoCAD 2010Tutorial will show how Tables have been automated.

AutoCAD 2010 Tutorial 6 - Get Rid of RedrawingObjects Once and for All

The following AutoCAD 2010 Tutorial describes the block panel in the ribbon.
http://www.auto-cad-tutorial.com/angular-dimension-command.htmlhttp://www.auto-cad-tutorial.com/angular-dimension-command.htmlhttp://www.auto-cad-tutorial.com/angular-dimension-command.htmlhttp://www.auto-cad-tutorial.com/arc-length-dimension.htmlhttp://www.auto-cad-tutorial.com/diameter-and-radius.htmlhttp://www.auto-cad-tutorial.com/jog-line-command.htmlhttp://www.auto-cad-tutorial.com/multileader-command.htmlhttp://www.auto-cad-tutorial.com/table-command.htmlhttp://www.auto-cad-tutorial.com/table-command.htmlhttp://www.auto-cad-tutorial.com/multileader-command.htmlhttp://www.auto-cad-tutorial.com/jog-line-command.htmlhttp://www.auto-cad-tutorial.com/diameter-and-radius.htmlhttp://www.auto-cad-tutorial.com/arc-length-dimension.html


15/21

Making an AutoCAD block can be described as picking objects and organizing them with

each another to create only one object. That one object is also referred to as a blockdefinition. The objects in a block appear no differently than they do in your drawing.

Insert Command

Blocks produced in a drawing are called local blocks. Local blocks and, in fact, any otherAutoCAD .dwg file may be inserted just like a block by making use of the insert command.

Block Command

The Block command creates blocks by way of the Block Definition dialog box. The block

definition is saved once within the drawing and can be inserted into your drawing numeroustimes.

Block Editor

It is possible to modify a local block definition in your drawing by using the Block Editor.

wBlock Command

The wblock command can export local blocks, which turns them into separate files. Wblockis located else where in the ribbon but I'll include it here.
http://www.auto-cad-tutorial.com/insert-command.htmlhttp://www.auto-cad-tutorial.com/block-command.htmlhttp://www.auto-cad-tutorial.com/block-editor.htmlhttp://www.auto-cad-tutorial.com/wblock-command.htmlhttp://www.auto-cad-tutorial.com/wblock-command.htmlhttp://www.auto-cad-tutorial.com/block-editor.htmlhttp://www.auto-cad-tutorial.com/block-command.htmlhttp://www.auto-cad-tutorial.com/insert-command.html


16/21

AutoCAD 2010 Tutorial 7 - The Properties PanelHow To

This specific AutoCAD 2010 tutorial discusses how the properties of object can be modifiedfrom the Home Tab in the Properties panel.

You will find a couple of ways to give objects their properties: first is by using layers. The objects receive the attributes of the layers they're placed

on. Generally, this is most desirable way to manage properties.

secondly, properties can be designated to an individual object, despite the layerthey're on.

List Command

You can check the specifications objects in your drawing with the information displayed bythe list command.
http://www.auto-cad-tutorial.com/list-command.htmlhttp://www.auto-cad-tutorial.com/list-command.html


17/21

Control BoxesFor quick access to certain object properties the panel features drop down boxes.

AutoCAD 2010 Tutorial 8 - The Utilities Panel

In this AutoCAD 2010 Tutorial we are going to use the assorted tools in the Utilities panel tohelp you retrieve info about your drawing.

Measure Tools

The tools in the measure drop-down menu are a group of commands known as inquirycommands.
http://www.auto-cad-tutorial.com/measure-tools.htmlhttp://www.auto-cad-tutorial.com/measure-tools.html


18/21

Quick Select Command

You can search and find objects, by using a dialog box, by object type or a specific property.

Select AllObjects become highlighted once they are selected and return their normal appearance oncethe command is completed.

Quick Calculator

This is a stand alone calculator that opens in a seperate palette.

ID CommandThe coordinate location of any point in your drawing can be found using ID point icon.

Point StyleThe point style command has been included in the point command tutorial.

AutoCAD 2010 Tutorial 9 - The Clipboard Panel

This AutoCAD 2010 Tutorial will review copying and pasting using the commands in theClipboard panel.
http://www.auto-cad-tutorial.com/quick-select.htmlhttp://www.auto-cad-tutorial.com/quick-calculator.htmlhttp://www.auto-cad-tutorial.com/point-command.htmlhttp://www.auto-cad-tutorial.com/point-command.htmlhttp://www.auto-cad-tutorial.com/quick-calculator.htmlhttp://www.auto-cad-tutorial.com/quick-select.html


19/21

Pasteclip Command

There are two ways in which to paste in AutoCAD. The first way is by embedding the object

which makes the object a permanent part of the drawing. The second way is by linking, theobject is only shown in the drawing.

Cutclip Command

The cut object is actually erased from a drawing.

Copyclip Command

You are able to copy more than just objects between drawings, object linking andembedding allows you to copy pictures, spreadsheets, text etc.

Match Properties

One object will be used as the source, where the properties come from, one or more objectcan then receive those properties.AutoCAD 2010 Tutorial 10 - Printing Tools in the

Plot Panel
http://www.auto-cad-tutorial.com/copyclip-pasteclip-cutclip.htmlhttp://www.auto-cad-tutorial.com/copyclip-pasteclip-cutclip.htmlhttp://www.auto-cad-tutorial.com/copyclip-pasteclip-cutclip.htmlhttp://www.auto-cad-tutorial.com/match-properties.htmlhttp://www.auto-cad-tutorial.com/match-properties.htmlhttp://www.auto-cad-tutorial.com/copyclip-pasteclip-cutclip.htmlhttp://www.auto-cad-tutorial.com/copyclip-pasteclip-cutclip.htmlhttp://www.auto-cad-tutorial.com/copyclip-pasteclip-cutclip.html


20/21

This AutoCAD 2010 Tutorial explains the process of creating a hard copy printed set ofdrawings by explaining the commands in the Plot Panel.

Plot Command

The terms plotting and printing typically refers to the type of peripheral device you send

your drawings to, for example, a pen plotter for plotting and a laser printer for printing.

PreviewPlotting uses the default settings in the page set up. It is always a good idea to previewyour drawing before its sent to the printer.

Ribbon > Output Tab > Plot Panel > Preview tool button

Page Setup Manager

Model space layouts and paper space layouts are applied to their respective drawing space.

Plot and Publish Details Command

When a print job is finished, a notification balloon will appear in the lower right corner of thestatus bar. Click it to review the details of plot.

Plotter ManagerHere you can add a new plotter configuration or edit an existing one. The output file can be

a plot file (.plt), design web format file (.dwf), portable document format (.pdf) or variousraster image files.
http://www.auto-cad-tutorial.com/plot-command.htmlhttp://www.auto-cad-tutorial.com/page-setup-manager.htmlhttp://www.auto-cad-tutorial.com/plot-and-publish.htmlhttp://www.auto-cad-tutorial.com/plot-and-publish.htmlhttp://www.auto-cad-tutorial.com/page-setup-manager.htmlhttp://www.auto-cad-tutorial.com/plot-command.html


21/21

Plot Style Manager

This command opens a folder where all the plot style tables are kept.
http://www.auto-cad-tutorial.com/plot-style-manager.htmlhttp://www.auto-cad-tutorial.com/plot-style-manager.html

autocad 2010 tutorial 1

Documents