7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 1/37

This document shows how to configure AXXXEdge(9200) for ip over dcc interface.

There are 2 major steps to be carried out for login

Step 1.Initial configuration thru CLI login.

Step 2.Configuration thru Craft terminal session.

A fresh node configuration should always be carried out starting with initial configuration

thru CLI login.

STEP 1. CLI Login1. Initial configuration through CLI is used to assign community-handler,

management-node and IP address to the node.2. Connect craft craft cable to VT100 port of the node.

3. Doule click on the computer icon on the bottom right corner of the craft terminal

window.

4. Give port name COM1 and press OK.

5. Press ENTER to get the “ >” sign on the window.

6. Type “axxcli” and password “axxcli”.7. The prompt “axxcli” will appear.

8. Type “com” to enter to “Community-handler” command prompt.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 2/37

9. Type “add manager=0.0.0.0 community=public access=super t=d” and press

enter.

10. Press dot “.” twice and enter to come back to axxcli prompt.11. Type “management” to enter to management node command prompt.

12. Type “sys sys=ipunnumbered” and “yes” to confirm.

13. Press “.” Twice and enter to come back to axxcli prompt.14. type “ip ip=X.X.X.X subnet=Y.Y.Y.Y” and press enter (X.X.X.X stands for the

ip address of the node and Y.Y.Y.Y for subnet mask 

15. type exit and press enter 16. The node is ready to have craft login session through cross cable.

17. The CLI.txt file shows the commands run on the system.

 N.B: The command axxcli>erase will erase the complete configuration database andthe node has to be configured again starting from CLI login.

STEP 2: Craft Session

To get into the node thru craft terminal connect the cross cable to the mngt port on the

AXX.1. In the TCP/IP properties of the LAN port give ip of the node as laptop Gateway

ip ,Subnet mask same as that of the AXX node and IP of the laptop different from

the IP of the node.2. In the craft terminal give ip of the node which was assigned thru the CLI login.

3. User name “admin” and password “public” and press “logon”.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 3/37

4. The main window appears on the screen.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 4/37

5. Click on slot1- unequipped and scroll down on the expected module to choose

the type of card used in that slot .Save. Refresh the screen. Enable alarm

reporting 

6. The install state will change from installed and unexpected to installed andexpected and the service state should be in service.

7. The s-shot below shows the final state.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 5/37

7. Repeat the steps 5 and 6 for slot number 2 and the installed and expected card

should be 63*E1 tributary card. Enable the Alarm reporting.

8. Open the slot-1 tree and Right-click on the SDH-1.1 and click structure. A SDHstructuring wizard will appear. Keep clicking next till it asks for structure type.

9. ChooseTU-12 to cross-connect and click next and finish.

10. Repeat the step 8 and 9 for SDH 1.2 also and structure it to TU-12 level.

 

.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 6/37

11. Click on the management interfaces in the management tree.

12. Click management Dcc on the right.

13. Change the mode on both the Dcc-M to “Ip over DCC” and save 

13 Refer below for the screen shot

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 7/37

14. Click on the managementinterfaces on in the management tree.

15. Click the DCN router, enable IPunnumbered gateway and save.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 8/37

16. Click on OSPF and set administrative status to Enable.

17. Click areaOSPF ,click Add on top and give the required area ID and

save.Imp:The area ID once set cannot be changed unless we erase the whole

node completely and reconfigure.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 9/37

This completes the basic configuration in Ipunnumbered mode.

Cross-connections can be made only after the SDH ports are structured.

To make cross-connections.

1. Go to Equipment on top of main window and select cross-connect.2. Press search now.

3. Under the available Tps will show all the KLMs from Port 1 and 2 and all the 63

E1 ports.4. 1/1/1.1.1.1.1 means slot/port/C.B.K.L.M

5. Hence 1/2/1.1.3.7.3 means slot1, SDH port 2 the KLM is 3-7-3.C.B is constant1.1

6. But 2/51/1.1.1.1.1 means slot 2 which is tributary card and port no 51 on the patch

 panel or E1 number 51. 1.1.1.1.1 is constant for tributary card.

7 To pass thru the KLM select slot1 port 1 KLM, Right click and select ADD.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 10/37

8 select slot 1 port 2 KLM ,right click and select Set B and save. The connection

will be shown in the right window and the graphical view can also be seen.

9 To drop any particular KLM onto tributary port, select the tributary port first,right click and select ADD. Then select the KLM for the particular SDH port,

right click and select Set B. Save the connection.

10 To provide protection to the tributary port in step 9, complete step 9 and selectthe KLM of left SDH port, right click and select Set Prot and save.

11 Below S-shot provide you with all the 3 examples.

Cross-connect window

1. 1/1/1.1.1.1.1(A) pass thru to (1/2/1.1.1.1.1)2. KLM 1.1.2 from slot 1 Sdh port 1( B ) is dropped onto tributary port 1 of slot 2.

3. Tributary port 2 of slot 2 (A) is attached with KLM 1.1.3 from slot1 sdh port 1(B)

and is protected by KLM 1.1.3 of slot 1 sdh port 2.(Protection).

 

12.It is recommended to make all the KLMs collectively pass thru. Then delete the

required KLMs on the right window which are supposed to dropped locally. It makes

the task easier. Click save after deleting and the deleted Tps will appear in the columnof available Tps.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 11/37

To set system time.

1. Go to equipment and select commissioning wizard.2. click next till basic set-up. Fill information for the node in network element

information

3. click next

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 12/37

3 In Expected service module check for any left out unequipped slots. if none click 

next until you find alarm reporting.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 13/37

4 .In alarm reporting select the power modules which are used

Click next.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 14/37

5. In date and time , select synchronize to work station.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 15/37

6. Click next and save.

To enable alarm status of the tributary port and giving the loops.1. In the management tree open the slot -2 63XE1 card tree.

2. Click the particular pdh port being used. Change administrative status to Enable.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 16/37

3. Open the PDH port further to find E1.Select the E1 and change administrative 

loop mode from no loop to the required loop and save. Two loops can be given – 

network or ll2 loop and customer or ll3 loop

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 17/37

 

To define synchronization.

1. Go to devices in the management tree. Click synchronization on the right .

2. Click  T0synchsource.Click ADD on top.

3. If clock source is E1 level which is dropped onto any tributary port3.1 Click the E1 port of the selected PDH from where we have to give the

clock.

3.2 Define the E1 mode as PRA . Default mode is TRA

3.3 Now in the T0syncsource frame select slot 2 and the port to the

corresponding E1, disable SSM, administrative quality as PRC , give priority and save.

4. If providing SDH clock select slot1 1 port of the particular SDH, give priority and

SSM is by enabled by default.

5. Save the changes.

6. Check for the operational quality of the clock.7. Defining synchronization is necessary otherwise minor epj (excessive pointer 

 justification) alarm will be there in the network.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 18/37

This screen shows how to put the selected E1 mode to PRA.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 19/37

This screen shows clock is defined at E1 and SDH level with different priority. This

is only for explanation.

To upgrade software in the node.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 20/37

1. The below screen shows the older running software version R2.0 ICS09.

2.Go to Equipment and select NE Maintenance.

3. Wait for 5 seconds. The window will expand automatically.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 21/37

4. click on the Device and highlight the bank on the right screen.

5.click download on the top left of screen.

6. The new window may not contain the patch file for up gradation. Click on Add file

to repository and fetch the file on the system. The file is attached.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 22/37

7. Highlight the fetched patch and press next.

8. Select restart NE time immediately.

9 Select auto switch bank.

10 press next and finish. 

The screen below the process of downloading the file to the node.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 23/37

After the download is complete the screen will appear showing the new software

version successfully downloaded.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 24/37

The version has been upgraded from ICS 2.0.9 to the latest version I.C.S 2.1.04.

 N.B: There is a change in the procedure for software up gradation in the node. The abovemention procedure is carried out in Device in NE maintenance. Before doing this step on

the device, the same above mentioned steps from step 4 till step 10 has to be carried for the System controller.

  By the time I have framed the document the up gradation has already been done, hence I

am unable to provide the screen-shots but will mail you soon the procedure when I get to

work on the fresh node.

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 25/37

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 26/37

POWER CONNECTION

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 27/37

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 28/37

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 29/37

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 30/37

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 31/37

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 32/37

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 33/37

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 34/37

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 35/37

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 36/37

7/27/2019 AXXXEdge Configuration

http://slidepdf.com/reader/full/axxxedge-configuration 37/37