b. operation guidance user m an l t hnk y ou fr c si g t e … · 15v 1a input port jump start...
TRANSCRIPT
EPOWER Charging Instruction:Charging by wall adapter1. Plug in power adapter to wall outlet2. Connect 15V1A connector to the input port on EPOWER
2
Fuse ProtectionOvercharge and
Overdischarge ProtectionAgainst-reverse Plug
I. WARRANTY INFORMATION: 1.We offer a limited warranty for this product against any defects in material and workmanship for a period of 12 months from the date of purchase by the end user/consumer. The conditions of the warranty are as follows:
2.The warranty is only valid upon presentation of the original receipt (from dealer/retailer) by the original purchaser with the product to be repaired or replaced
3.The warranty is void if the serial number, date of purchase and label has been removed
4.The warranty does not cover damage or product failure resulting from normal wear and tear, physical abuse, improper installation, misuse, modification or repairs by unauthorized third parties
5.We do not assume responsibility for any loss or damage incurred during shipment or as a result of a force majeure
6.We are not liable for any incidental or consequential damages arising from the use or misuse of this product
7.All warranty claims are limited to repair or replacement of the defective product and at the sole discretion of us
8.If we repair or replace the product, the product will be covered for the remaining time of the original warranty period. Repair or replacement may involve the use of reconditioned units which are equivalent in function. Replaced part or product becomes the property of us
9.Consumable components such as batteries are not covered by the warranty
8
Applied Standard GB/T 18287-2000:
H. Warning:1. Always make sure the blue plug is securely connected on EPOWER before attempting to jump start a vehicle. Otherwise it can cause the blue plug to overheat and melt.2. Always check the jumper clamps make sure they are well connected, check the vehicle battery terminals for rust or dirt, clean them before jump start a vehicle. DO NOT continue to jump start more than 3 unsuccessful attempts. It can damage the battery. Check your vehicle for other issues.3. DO NOT connect two clamps, it is dangerous!4. DO NOT disassemble the unit, it may cause damages!
Always take care when using the EPOWER
This EPOWER is not intended for use by young or infirm persons without
supervision
Do not use as a toy
Do not allow the EPOWER to become wet
Do not immerse the EPOWER in water
Do not operate the EPOWER in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust
Do not modify or disassemble EPOWER. Only a repair technician may
repair this unit
Do not expose the EPOWER to heat
Do not store in locations where the temperature may exceed 70 °C
Charge only at ambient temperatures between 0 °C and 40 °C
Charge only using the charger provided with the EPOWER
Under extreme conditions, battery leakage may occur. Carefully wipe the
liquid off using a cloth and avoid skin contact when you notice liquid on
the batteries. In case of skin or eye contact, rinse immediately with clean
water and seek medical attention
At the end of their useful life, discard the EPOWER with due care for our
environment7
!
!
!
!
Q.A. Approx. 5 times for iPhone 6.
Q. How long will this EPOWER on a full charge take to supply the Notebook? A. 2-3 hours
Q. in full battery?A. Approx. 20 times.
Q. Once the device is fully charged, how long can it be stored without a charge but still be able to jump start a vehicle?A. Proximately 6-12 Months. But to prolong the rechargeable battery life, it is recommended to recharge every 3 months.
How many times can this EPOWER charge for my cell phone?
How many times can this EPOWER jump start the vehicle if it is
F. TROUBLE SHOOTING: Finding Cause Remedies
No response when pressing the switch button.
Low voltage protection of EPOWER is started.
Plug the adaptor into the 15V 1A input port to activate.
6
G. TOXIC AND HARMFUL SUBSTANCES:
O:Indicate all homogeneous materials' hazardous substances content are below the MCV limit specified
in the Standard 2002/95/EC(RoHs).
Composition and amount of toxic and harmful substances in EPOWER
( ) Pb Hg Cd Cr Vi PBB PBDE
O O O O O O
LED flash lightPress the switch 3 seconds to start the LED flash light. There are 4 modes of LED light appear in order (normal. strobe. SOS. off) if you press slightly.
C. PARTS LIST :
5
E. FAQ: Q.A. charging is complete
Q. How long time to full charge the Epower?A. Approx. 3-4 hours through the 15V1A input.
How to turn off this EPOWER? This EPOWER will power off automatically when no load or
USER MANUAL
Thank you for choosing the EPOWER! Always follow basic safety precautions when using electrical EPOWERs. Read al l instructions careful ly, Please keep this instruction manual for easy reference
A. PRODUCT LAYOUT:
1
Charging Cell Phone or Tablet Instruction:1. Plug the switch cable B to USB 5V 2.4A output port.2. Select appropriate connector and connect it to your mobile
phones or tablet.3. Press the switch button to charge.
3
For power supply to 12V vehicle products or 12V electronics1. Plug the optional switch cable to 12V 10A output port.2. Connect the optional switch cable and 12V vehicle product or 12V electronics.3. Press the switch button to power supply.
RED LIGHT on with buzzing: The connection is wrong, correct the clamps as indicated in step 2 mentioned above, wait until the GREEN LIGHT is on to turn on the engine.
GREEN LIGHT on: Connection is correct and circuit is working, you can turn on the engine to jump start the vehicle.
4. Start the vehicle5. When the vehicle is started, remove the jumper cable from thevehicle battery. Leave the vehicle's engine running.
GREEN LIGHT blinking with buzzing: Vehicle battery is low, press the "BOOST" button and wait for the GREEN LIGHT become solid, then turn on the engine within 30 seconds.
No Lights, No buzzing: The vehicle's battery may be damaged, inspect the clamps are in correct position, press the "BOOST" button, wait for the GREEN LIGHT to turn on, and then turn on the engine within 30 seconds.
Beep,Beep
Beep,Beep
Jump start vehicle instruction:
1. Connect the blue plug end to the EPOWER and make sure the cable indicator is off.2. Connect the Red Clamp to the positive (+) battery terminal, Black Clamp to the negative (-) battery terminal.3. Cable light indicator instructions:
BOOST reverse correct
15V 1A input port
Switch
Jump start socket
Mic USB5V 2A input port
USB 5V 2.4A output portLED Switch
12V 10A output port
19V 3.5A output port
Power adapter
15V 1A input port Jump start socket USB 5V 2.4A
output port
12V 10A output port19V 3.5A output port
Switch cable A
Switch cable B
For 12V vehicle productsIntelligence Jumper cable
Car adapter
LCD Display
B. OPERATION GUIDANCELCD Display Description: 1. Battery level:Press switch button ( ) , LCD displays "BATTERY" also showing XX% indicating battery percentage. If it shows "LOW BATTERY RECHARGE NOW", it indicates that battery is low, please recharge it.2. Charge the battery:Connect EPOWER with a wall adapter or car charger to charge the device. LCD displays "CHARGING" when connected to power sourcing, also a charge light will also turn on.3. LED emergency light:3. LED emergency light:Press EPOWER master light switch ( ) to turn on the flashlight. Switch between different modes by keep pressing the button: LCD displays LIGHT indicating normal strobe mode, FLASH indicating SOS distress mode, press one more time to turn off.4. Power output:Connect a USB cable to 5V2.4A USB1(USB2) output port, press power switch( ) to display 5V2A, then connect your mobile phones, tablets and other 5V electronic device to the USB cable to charge.Connect a 19V cable to the 19V3.5A port and press power switch, display will show 19V ON, it can supply power to laptop computers.To use 12V car jump start: connect to 12V10A port, connect the red clamp to positive terminal on the battery and black clamp to negative terminal.
4
Only for charging/power supply to 19V Notebook1. Plug the switch cable A to USB 19V 3.5A output port.2. Select appropriate connector for your Notebook and connect it to the switch cable A and your Notebook.3. Press the switch button to charge/power supply.
D. TECHNICAL SPECIFICATIONS: Size: 172*86*36mm
Weight: 480g
Battery Capacity: 12000mAh(44.4Wh)
Output: Dual 5V 2.4A; 12V 10A;19V 3.5A;12V Jump Start
Input: 15V 1A;5V 2A
Full charging time:3-4 hours for 15V1A ; 6-7 hours for 5V2A
Starting current:200A
Peak current:400A
Operating temperature : -20℃ ~ 60℃
#
1
3
4 otebook
Parts Name Quantity
2
EPOWER
Switch cable A
Switch cable B
N connector
5 Cigar Socket Cable
#
6
7
8 I
Parts Name Quantity
Home adaptor
Car adaptor
ntelligent jumper cable
9 User Manual
Charging by USB charger cable1. Plug in the USB charger to any working USB output port.2. Connect the micro USB end of the cable to the 5V2A input port on EPOWER.Charging by car adapter1.Plug in the car adapter into cigarette lighter socket of a vehicle.2. Connect the other end to the 15V1A input port of EPOWER.
1
1
1
1
1
1
1
8
Remove the battery of your Notebook and use this EPOWER to supply power directly, or disconnect EPOWER with your Notebook and connect them when it is cool.
EPOWER is a bit hot when charging for Notebook.
The charging current is a bit high (3.5A)
All 12V10A,5V2.4A,19V3.5A have no output when pressing the switch button
Overcurrent protection function started and cut the circuit.
Plug the adaptor into the 15V 1A input port to activate
1