bpa tadiran

Contents

HF Base Antennas

Travelling Wave Dipole page1 Log Periodic page 6 Folded Dipole page 2 Biconical Dipole page 8 Semi Delta page 3 Rhombic 1.6-30 page 10 Delta page 4 Rhombic 2-30 page 13

HF Vehicle Antennas

Heavy Duty Vehicle Whip p. 16 NATO Vehicle Whip Base p. 17 Standard Vehicle Whip Base p. 18

HF Tactical/Portable/Man-pack Antennas

Man-pack Collapsible Whips p. 19 Tactical End Fed p. 20 Man-pack Goose Neck p.19 Man-pack Tape Whip p. 21

VHF Base Antennas

VHF Biconical Dipole p. 22 VHF Discone p. 26 VHF Folded Monopole p. 25 VHF Marine Discone p.27

VHF Tactical/Portable/Man-pack Antennas

VHF Folding Log Periodic p. 28 VHF Man-pack Tape Whip p. 31 VHF Hand-held Rubber Ducky p. 29 VHF Man-pack Tape Whip PTR-349 p.32 VHF Hand-held Rubber Ducky PTR-349 p.30

UHF Base Antennas

UHF Discone p. 26 4 Element Corner Reflector p. 34 UHF Marine Discone p. 27 6 Element Corner Reflector p. 35 UHF Log Periodic p.33

UHF Tactical/Portable/Man-pack Antennas

UHF Folding Log Periodic p. 28 UHF Handheld Rubber Ducky p. 29

Masts and Towers

Tactical Masts p. 37

BROADBAND PROPAGATION Antenna Design & Supply Phone: (08) 8388 8132 1-3 Adelaide Rd. Echunga Fax: (08) 8388 8536 PO Box 529 Echunga Intl.Phone: (618) 8388 8132 South Australia. 5153 Intl.Fax: (618) 8388 8536 E-mail: [email protected] ABN: 84 232 273 647 Web: www.broadbandpropagation.com

BPA-TWD HF BROADBAND DIPOLE This broadband dipole is a resistively terminated broadband antenna which when mounted as an inverted V has minimum lobe break up at the higher end of the HF spectrum. It has been specially developed as an HF reference antenna rather than a communications antenna. Constructed to the highest quality standards with powder-coated aluminium, balun and load cases, UV stabilized fiberglass spreaders, cable strain relief and connector weather shrouding.

Specifications Frequency range: 1-30 MHz Input Impedance: 50 Ohms nominal Power Input: 200 Watts CW Input Connector: N Female VSWR: Better or equal to 2.5:1 full band Better or equal to 2:1 most of the band* Max.Wind Speed: 250 kilometres/ hour*

Dimensions for Inverted Vee mounting

Central Mast height: 15 metres Outer Mast Height 2-2.5 metres Outer Mast spacing: 50 metres Shipping weight: 10 Kilograms Shipping size: > 132.5 x 31.5 x 24 cm *Measured at antenna feedpoint *In accordance with AS1170.2 SAA LOADING CODE; WIND LOADS 1989

Broadband Propagation Antenna Data Sheets - Page 1


FD-150-22m HF BROADBAND Folded Dipole The folded dipole is a resistively terminated broadband antenna which although inefficient compared with other broadband HF designs* is low cost, compact, light and easily installed. The antenna is an old design first described in amateur circles in 1951. Barker and Williamson pioneered commercialization of the design and it is still a popular antenna, in widespread use. The antenna can be installed as a flat top, sloper or inverted "V". Our folded dipoles are, as with our other antennas, constructed to the highest quality standards with aluminium balun and load cases, UV stabilized fiberglass spreaders, cable strain relief and connector weather shrouding. No antenna tuner is required

Specifications Frequency range: 5-18 MHz Input Impedance: 50 Ohms nominal Power Input: 150 watts PEP Input Connector: UHF Socket VSWR: Better than or equal to 2:1 Max.Wind Speed: 250 kilometres/ hour*

Dimensions for Inverted Vee mounting

Central Mast height: 6.5 metres.(Minimum) Outer Mast Height 2.4 metres (Minimum) Outer Mast spacing: 24 metres Shipping weight: 6 Kilograms Shipping size: 800 x 650 x 200 mm Options #1 Supplied with nominated length RG58 or RG213 (low loss) coaxial cable fitted with connectors at both ends. #2 Supplied with Central Mast halyard and pulley Please specify (by description) when ordering > *In accordance with AS1170.2 SAA LOADING CODE; WIND LOADS 1989 *Measured at transceiver with 30m of RG 58 feeder



BPA-SD-500 BROADBAND HF SEMI DELTA OMNI DIRECTIONAL BASE ANTENNA The BPA-SD-500 is a 500 Watt rated Semi-Delta antenna with a high vertical gain radiation pattern, suitable for NVIS (short range) communication. With a small mounting footprint of 20m, it is ideal for installation where space is limited. No antenna tuner is required. Construction is of 3.2mm stainless steel cable with an aluminium spreader and die cast aluminium component cases. All external fittings and connections are of stainless steel. Specifications Frequency range: 2-30 MHz Feed Impedance: 50 Ohms Power Input: 500 Watts Input Connector: UHF type socket Mast height: 10 metres min. Wind rating: 210 k/h* Temperature: -30 to 55 deg. C. ambient Shipping weight: 17 kilograms Shipping size: 200 x 30 x 19 cm Options. 1. Supplied with 30 meters of RG 58 or RG 213 coaxial cable fitted with UHF or N connectors at both ends. 2. Central Pulley/halyard kit Please specify (by description) when ordering > *In accordance with AS1170.2 SAA LOADING CODE; WIND LOADS 1989 *Measured at transceiver with 30m of RG 58 feeder



BPA-DELTA 3-30-1000 ANTENNA The BPA-DELTA 3-30 1000, antenna is a broadband, omni-directional, vertically polarized antenna with a high angle of radiation suitable for short to medium range communication. (up to 1000 kms) A central Balun which is fed by 50 Ohm coax feeds both arms of the antenna. Antenna arms are supported by a 17m central mast (not supplied) and two stub masts (see drawing overleaf) Construction is of 3.2 mm stainless steel cable with UV stable fibre-glass spreaders and powder coated aluminium and glass reinforced polyester component cases. All external fittings and connections are of stainless steel. Lightning protection is provided. Specifications Frequency range: 3-30 MHz Feed Impedance: 50 Ohms Balun connection: N type socket Power Input: 1000 Watts PEP. VSWR: Better than 2:1* Mast height: 17 meters 52 meters Wind rating: 210 kilometers/ hour* Temperature: -30 to 55 deg. C ambient Shipping weight: 20 kilograms Shipping size: 200 x 31.5 x 24 cm Options. 1. Supplied with 30 meters of RG 58 or RG 213 coaxial cable fitted with UHF or N connectors at both ends. 2. Central Pulley/halyard kit Please specify (by description) when ordering > *In accordance with AS1170.2 SAA LOADING CODE; WIND LOADS 1989 *Measured at transceiver with 30m of RG 58 feeder *Antenna height 10m, Gnd: Diel const. 10, Cond. 0.002


BPA-DELTA 3-30-1000 ANTENNA


BROADBAND PROPAGATION Antenna Design & Supply Phone: (08) 8388 8132 1-3 Adelaide Rd. Echunga Fax: .(08) 8388 8536 PO Box 529 Echunga Intl.Phone: .(618) 8388 8132 South Australia. 5153 Intl.Fax: (618) 8388 8536 E-mail: [email protected] ABN: 84 232 273 647 Web: www.broadbandpropagation.com

HF BROADBAND HORIZONTALLY POLARISED LOG PERIODIC ANTENNA Models: BPLP-2-30, BPLP-3-30 and BPLP-5-30

Our HF Broadband Log Periodics are almost 100% efficient and are short to medium range antennas. They can be supplied in a number of models to suit differing frequency spans. They are high gain and directional and can be configured as bi-directional if two are mounted back to back. The antennas are end fed and can be supplied with power ratings ranging from 200 watts, to 10 Kilowatts CW (Continuous). The antennas are almost 100% efficient across the full operating range of frequencies. Radiation is horizontally polarised Full lightning protection is provided


Specifications

BPLP-2-30 BPLP-3-30 BPLP-5-30

Electrical Frequency: 2-30 MHz 3-30 MHz 5-30 MHz Gain: Dependant on frequency 8-13 dBi VSWR: 2.0-1 most of band, 2.5:1 maximum Polarisation: Horizontal Power Rating : 250 watt average (1 kW PEP) 1Kilowatt average (4 kW PEP) and 10 Kilowatt (40 kW PEP) models available Input Impedance: 50 ohms Input connection: Dependant on power rating Mechanical Mast Height: 23m 18m 12m Overall length: 130m 100m 65m Overall Width: 80m 62m 40m Wind Rating 150 km/hr All metal materials are of high grade stainless steel or hot-dip galvanised steel. Ceramic insulators used throughout. RADIATION PATTERNS



HF BROADBAND BICONICAL DIPOLE Models: BPBD-2-30 and: BPBD-3-30

Our HF broadband Biconical Dipoles are highly efficient, horizontally polarised antennas that at lower frequencies are suitable for short to medium range communication and at the higher frequencies have the strongest signals at lower angles for long range propagation. The antenna is centre fed and can be supplied with power ratings ranging from 200 watts, to 10 Kilowatts CW (Continuous). The antennas are almost 100% efficient across the full operating range of frequencies. The antenna is ideal for frequency agile transmissions and is constructed of high grade materials throughout. Full lightning protection is provided


Specifications

BPBD-2-30 BPBD-3-30

Electrical Frequency: 2-30 MHz 3-30 MHz Gain: 8.5 dBi VSWR: 2.0-1 most of band, 2.5:1 maximum Polarisation: Horizontal Power Rating : 250 watt average (1 kW PEP) 1Kilowatt average (4 kW PEP) and 10 Kilowatt (40 kW PEP) models available Input Impedance: 50 ohms Input connection: Dependant on power rating Mechanical Mast Height: 20m 15m Overall length: 101m 72m Overall Width: 40m 30m Wind Rating 230 km/hr All metal materials are of high grade stainless steel or hot-dip galvanised steel. Ceramic insulators used throughout.



HF BROADBAND RHOMBIC ANTENNA

Model: BPRH-1.6-30

Rhombic antennas have high directional gain and low take-off angles and are best suited to long distance, point to point communications. Rhombic antennas suited to operation down as low as 1.6 MHz are large. The BPRH-1.6-30 requires four masts but installation of the antenna itself Is simple and can be carried out without specialist skills. Long term maintenance requirements are low. Our HF Rhombic range offer a cost effective answer for permanent base stations where low take-off angle, and high directional gain is needed, with good radiation efficiency.

Page 1 of 3 jb RHOMBIC 1.6-30 SPECs.doc 2008


Specifications: BPRH-1.6-30

Electrical Frequency Range: 1.6-30 MHz VSWR: Better than 2.0 : 1 across band Main Lobe Freq. MHz Gain dBi Take-off Angle ° Power Efficiency %

1.6 3.0 38 47 2 5.2 35 79 5 13.9 20 79 10 20.1 12 81 15 22.0 8 82 20 23.9 6 80 25 23.0 5 79 30 20.5 4 79

Polarisation: Horizontal Power Rating: Antenna only, Max. 30 kW Average, 60 kW PEP, Overall rating dependant on ratings of Balun and Termination pair Which are available from 1-20 kW Input Impedance: 50 ohms Input connection: Dependant on balun power rating Mechanical Mast Height: 30m Overall length: 620m Overall Width: 135m Wind Rating: 150 km/hr Construction All metal materials are of high grade stainless steel or hot-dip galvanised steel. Ceramic insulators used throughout. General The antenna is supplied with all fittings required for installation, masts are not included. Masts may be quoted separately if you would like us to supply these also. The antenna may be fed via coaxial cable to the tower mounted balun or can be fed via suitable balanced open wire line from the transmitter “hut”. Balun and termination requirements are dependant on the power rating require for the installation and are available from 1-20 kW. Page 2 of 3 jb RHOMBIC 1.6-30 SPECs.doc 2008


VERTICAL RADIATION PATTERNS

Page 3 of 3 jb RHOMBIC 1.6-30 SPECs.doc 2008



HF BROADBAND RHOMBIC ANTENNA

Model: BPRH-2-30

Rhombic antennas have high directional gain and low take-off angles and are best suited to long distance, point to point communications. Rhombic antennas suited to operation down as low as 2 MHz are large. The BPRH-2-30 requires four masts. Installation of the antenna Is simple and can be carried out without specialist skills. Our HF Rhombic range offer a cost effective answer for permanent base stations where low take-off angle, and high directional gain is needed, with good radiation efficiency.

Page 1 of 3 jb RHOMBIC 2-30 SPECs.doc 2008


Specifications: BPRH-2-30

Electrical Frequency Range: 2-30 MHz VSWR: Better than 2.0 : 1 across band Main Lobe Freq. MHz Gain dBi Take-off Angle ° Power Efficiency %

2 5.2 35 79 5 13.9 20 79 10 20.1 12 81 15 22.0 8 82 20 23.9 6 80 25 23.0 5 79 30 20.5 4 79

Polarisation: Horizontal Power Rating: Antenna only (all Models) Max. 30 kW Average, 60 kW PEP, Overall rating dependant on ratings of Balun and Termination pair Which are available from 1-20 kW Input Impedance: 50 ohms Input connection: Dependant on balun power rating Mechanical Mast Height: 30m Overall length: 620m Overall Width: 135m Wind Rating: 150 km/hr Construction All metal materials are of high grade stainless steel or hot-dip galvanised steel. Ceramic insulators used throughout. General The antenna is supplied with all fittings required for installation, masts are not included. Masts may be quoted separately if you would like us to supply these also. The antenna may be fed via coaxial cable to the tower mounted balun or can be fed via suitable balanced open wire line from the transmitter “hut”. Balun and termination requirements are dependant on the power rating require for the installation and are available from 1-20 kW. Page 2 of 3 jb RHOMBIC 2-30 SPECs.doc 2008


VERTICAL RADIATION PATTERNS

Page 3 of 3 jb RHOMBIC 2-30 SPECs.doc 2008



BPV-160-24 Heavy Duty Glass Fibre Whip The BPV-160-24 is a ruggedly constructed tuned whip built from a solid glass fibre core covered with a heavy-duty braided copper conductor and an insulating sheath. Solid construction offers greatly increased impact survival over hollow glass fibre whips. (Survives better than 35 impacts at midpoint at speed of 40 Km/h) The insulating sheath enables it to be used in environments where there is risk of contact with high voltage sources such as fallen power lines. The fully enclosing copper, braided conductor enables a very efficient transfer of radiated power.

Note: The antenna needs to be used with a suitable Antenna Tuner Unit.

Specifications Frequency range: 1.5 to 30 MHz tuneable Input Impedance: 50 Ohms (with suitable tuner) Power Rating: 160 watts Polarisation: Vertical Radiation pattern: Omni-Directional Colour: Matt Black overall Diameter: 15mm Length: 2.4m Weight: 1.3 kg Impact: better than 35 impacts midpoint at speed of 40 km/h) Mounting: Standard mount is via ½” Whitworth stud. (Can be supplied with other base attachment formats or threads) Note: drawing shows base which is not included.



BPV- BASE160-24 Heavy Duty Military Vehicle Antenna Base Designed and constructed for maximum strength and durability from aluminium alloy, stainless steel and high tensile fasteners. The body is machined from a solid billet of Acetal Copolymer (Delrin) and the base is fitted with a very rugged heavy duty barrel spring The mounting flange accommodates both UK/ NATO 6 or 3 hole pattern and USA 4 hole pattern enabling a standard fit on most military vehicles.

SPECIFICATIONS

Mounting: UK/ NATO 6 or 3 hole pattern and USA 4 hole pattern Power Rating: One Kilowatt Connection: Via heavy duty HV cable with stud clamp. Impact: In conjunction with a 2m non destructible test Whip, better than 200 impacts at 40 km/h Color: Matt Black overall Base Diameter: 140mm Overall height: 250mm Weight: 2.23 Kilograms Whip Attachment: ½” Whitworth female as standard (other thread or style can be specified)



BPV- BSE- HF Heavy Duty HF Antenna Base Designed and constructed for maximum strength this HF antenna base is a “top of the line” product which Has been designed for Military HF use where a NATO/ US style base is not required. Its price also makes it attractive to non-military users who require the very best in antenna bases. It is fitted with an extremely rugged, heavy duty “barrel” spring and can be supplied with either PL 529 (UHF) style connector or an N type connector for 50 Ohm input into a tapped or tuned whip antenna or With a feed terminal for use with an external tuner

Specifications Input Connection: PL 259, or N type (50 Ohms) or 6mm Input terminal for use with Antenna tuner. Power Rating: One Kilowatt Continuous Impact: In conjunction with a 2m non destructible test Whip, better than 200 impacts at 40 km/h Base Diameter: 55mm Length: 21.5 cm Weight: 1.74 kg Antenna Mounting: Standard mount is via ½” Whitworth stud Base Mounting Standard mount is via ½” Whitworth stud Can be supplied with other antenna and base, attachment formats or threads)



BPA-2-SW, BPA-6-SW, BPA-8-SW, BPA-10-SW COLLAPSIBLE BACKPACK WHIP ANTENNAS Lightweight, (a fraction of the weight of standard copper-coated steel Military backpack whips) our range is constructed from a highly specialized, heat treated and mechanically processed aluminium alloy with tensile and strength properties exceeding tubing of almost any other material including treated steel and glass laminates. Precision joint and tension cord system allowing rapid assembly and disassembly (in seconds) Available as standard in 2, 4, 6, 8 and 10 sections. Number of sections and section lengths can be tailored for custom orders. Standard tube diameter is 10mm but can also be supplied in other diameters. All whips are available with replaceable tension-cord option for field serviceability. Supplied with a range of standard radio connections including C, BNC and N type, threaded connectors to any format, or custom connectors to specification.

BPA-1-GN FLEXIBLE GOOSENECK A rugged flexible gooseneck for use with backpack whip antennas which allows firm positioning of the whip. The Gooseneck length is 145 mm and can be supplied with a range of standard radio connections including C, BNC and N type, threaded connectors to any format, or custom connectors to specification



SWQ-150-M HF Tactical Broadband Antenna The SWQ-150-M Tactical, Broad-band Antenna is a portable, HF broad-band antenna designed specifically for mobile and portable HF communication where rapid deployment and simplicity of operation is essential. It can also be installed as a semi-permanent base station antenna. The antenna will operate at all frequencies in the 2-30 MHz band without any adjustment or tuning required. It is ideal for use in conjunction with modern, digitally configured, HF communication transceivers where features such as ALE and frequency hopping require true broadband capability. No masts or guying are required. The antenna will work successfully supported by trees, the tops of vehicles or trucks or any convenient object or structure. The antenna works most effectively when supported at a reasonable height, but it will also radiate (with lower efficiency) when stretched out on the ground. (If no support is available) The radiation pattern of the antenna has a significant vertical component at all frequencies, making it ideal for NVIS applications. Deployment time is, typically, 15-20 seconds from unpack to ‘ready to go’ The antenna is supplied with Mil. Spec cable and connectors Component case is of rugged die-cast aluminium and the earth stake is of stainless steel with heavy-duty 0.315” (8mm) shaft. A 50’ (15m) throw line and 16’ (5m) ancillary line, of high quality braided nylon cord are included.

Specification Operating Frequency: 2-30 MHz Input Power: 150 watts SSB PEP Input Impedance: 50 Ω VSWR: Typically better than 2:1 across the band Input Connector: Supplied with 5 metres of coax fitted with N, UHF or BNC plug.

(Specify option required when ordering) Packed Weight: 2.9 lb (1.3 kg) Packed Size: 10” x 5”x 3” (254mm x 127mm x 76mm)



BP-HF-2-STW BACKPACK TAPE WHIP ANTENNAS Broadband Propagation manufactures a range of light-weight, flexible, tape whip antennas for use with HF man-pack transceivers. Standard length is one metre. Designed for use in tactical combat, in all types of operating conditions from arctic through to extreme desert environments they are constructed of highly durable, long-life, spring steel elements which will not break or lose their “set”. A flexible nylon braid covers the whip, increasing durability and providing high voltage contact protection. Antenna mounting connectors including thread, BNC, N, or C type can be provided or customer specified mountings can be supplied. The antenna is supplied with a goose neck base allowing for instant angle adjustment.

Fully Flexible

Customer Specified Mounting

Specifications

Frequency Range: 2-30 MHz Impedance: Nominal Radiation Pattern: Omni-Directional Polarisation: Vertical Power Rating: 10 watts CW Input Connection: Customer specified Antenna Length: 1.0 metres Antenna Width: 13 mm Antenna Weight: 130 grams Temperature Rating: -40 to +70 deg C . Integral Goose Neck

. Fully corrosion resistant . Sand abrasion resistant . Fungal attack protected . UV stable.



BPC-30-90 BICONICAL DIPOLE, BROADBAND BASE ANTENNA

Designed for ground, or ground to air, omnidirectional communications, the BPC-30-90 is a broadband, 16 element (8 fan and 8 skirt elements) antenna, covering the VHF band 30-90 MHz. It is designed as a semi portable base station antenna with ¼ turn attachment of the elements to the hub and rapid mounting to mast or pole. The hub is constructed of Acetal and anodised aluminium and the elements are UV stabilised fibreglass rods. A stainless steel stub mast is provided which attaches to the antenna. The stub mast is then clamped via supplied mounting clamps to any mast, pole or other structure with a diameter between 20-75 mm

Specifications Frequency Range: 30-90 MHz Gain: 3-4dBi Polarisation: Vertical VSWR: Equal to or better than 2.5 :1 Power Rating 500 watts Input Connection: N type female Mounting: Mounts to 20-75mm shaft via 600 x 38 mm stub shaft Finish: Olive drab Assembled Height: 3.46 metres Assembled Width: 3.32 metres Shipping Weight: 14 kg Shipping Dimensions: 162 x 30 x 13 cm Supplied with stub shaft and mounting Hardware.


VHF Biconical Dipole, Height 4 m over “average” ground

3D Plot @ 50 MHz

Vertical Plot @ 30-50 MHz

Vertical Plot @ 60-80 MHz


Horizontal Plot @ 30-70 MHz



VHF GROUND TO AIR ANTENNA Model: BPV-AIR-115-140

Designed for the aeronautical VHF band the BPV-AIR 115-140 is a compact vertically polarised antenna which operates in the frequency range of 115-140 Mhz with power handling of 100 watts continuous CW or 400 watts PEP. Antenna radiating elements are radome protected. It is fully environmentally protected aginst UV, corrosion, water ingress, dust/ sand abrasion and fungal attack, and offers reliable, long life operation in all environments from the tropics to Antarctica. The antenna includes a ground radial system and is tube mounted ALL external components are DC grounded to provide lightning and static discharge protection. Specifications

Frequency: 115-140 MHz Gain: 1-3 dBi across band VSWR: Maximum 2:1 across band Horizontal Pattern: Omnidirectional Polarisation: Vertical Power Rating : 100 watts average (CW continuous) 400 watts PEP Input Impedance: 50 ohms Input connection: N type Female Overall length: 1.01m Overall Width: 550 mm (ground-plane diameter) Wind Rating 230 km/hr Weight: 3.1 kg Mounting: Mounts to any circular spigot or tube 35 -50mm Diameter



VHF/ UHF DISCONE ANTENNA Model: BPV-LB-100-400

Designed for a variety of base station and tactical applications, the BPV-LB 100-400 is a compact vertically polarised broadband antenna which operates in the frequency range of 100-400 MHz with power handling of 500 watts CW. Mechanical construction of the antenna enables it to withstand the most rugged environmental conditions, with full protection against high wind loads, aggressive salt spray conditions, extreme temperature variation, and wind-borne sand abrasion. The antenna is pole mounted and can be provided with a range of mounting hardware to suit customer requirements. Full connector protection can be provided via a gland-entry weather shroud for marine/ salt spray environments (optional) * Lightning and static discharge protection is provided Specifications Frequency: 100-400 MHz Gain: 2 dBi typical VSWR: Maximum 2:1 across band Horizontal Pattern: Omnidirectional Polarisation: Vertical Power Rating : 500 watts average (CW continuous) Input Impedance: 50 ohms Input connection: N type Female Overall length: 0.8m Overall Width: 1.3m (ground-plane diameter) Wind Rating 230 km/hr Mounting: Mounts to any circular spigot or tube 30 -50mm Diameter (Or to customer requirement) VHF_UHF Discone.doc, Issue 0904



VHF/ UHF SHIPBOARD DISCONE ANTENNA Model: BPV-SPB-100-400

Designed for shipboard mounting, the BPV-SPB 100-400 is a compact vertically polarised broadband antenna which operates in the frequency range of 100-400 MHz with power handling of 300 watts CW. Antenna radiating elements are of marine grade stainless steel tube with a grey polyurethane lacquer finish. All other exposed surfaces are fully protected against aggressive, marine/ salt spray environments. The antenna is pole mounted and can be provided with a range of mounting hardware to suit customer requirements. * Full connector protection is provided via gland-entry weather shroud * Lightning and static discharge protection is provided Specifications Frequency: 100-400 MHz Gain: 2 dBi typical VSWR: Maximum 2:1 across band Horizontal Pattern: Omnidirectional Polarisation: Vertical Power Rating : 300 watts average (CW continuous) Input Impedance: 50 ohms Input connection: N type Female Overall length: 0.8m Overall Width: 1.3m (ground-plane diameter) Wind Rating 230 km/hr Mounting: Mounts to any circular spigot or tube 30 -50mm Diameter (Or to customer requirement) VHF_UHF Marine Discone.doc, Issue 0903



BP-LP-38-T VHF LOG PERIODIC ANTENNA - Transportable

The BP-LP-38-T is an 11 element log periodic antenna covering the VHF Band of 30 to 88 MHz, with a mid-band gain of 7dBi. And Front to Back ratio of 11dB Construction is of aluminium, with booms which disassemble for transport, The antenna elements also easily detach to enable the whole antenna to be reduced to a compact package for transport and storage. The antenna elements are fabricated from a special, ultra-high tensile Aluminium tubing which has a strength to weight ratio far exceeding tube steel or fibreglass (comparable to carbon fibre). Vertical and Horizontal polarisation modes are provided for. Mounting is via a standard 40mm spigot or alternative mounting can be provided if desired. The antenna is supplied with a sturdy canvas carry bag.

Specifications

Frequency Range: 30-88 MHz Impedance: 50 Ohms Gain: 4dBi Minimum to 7dBi Maximum Polarisation: Horizontal or Vertical F/B Ratio: 11 dB Beam Width E Plane 88 Deg. H plane 110 Deg.

Typical (Frequency. dependant) VSWR: Better than 3:1 Power Rating 400 watts PEP Input Connection: N type female (socket) Mounting: 40mm diameter mounting spigot No. of Elements: Eleven Antenna Length: 3.3 metres Antenna Width: 3.2 metres, At widest point Antenna Weight: 12 kg including carry bag



BP- VHF-UHF-RD VHF/ UHF HANDHELD TRANSCEIVER ANTENNAS Compressed Helical Type

A range of compressed helical “rubber ducky” whips for use with hand held transceivers operating in the VHF and UHF range The copper coated radiating element is covered in a protective poly-olefin shroud and is provided with a sturdy mounting base.

This is a rugged, tough, antenna designed for use in tactical combat in all types of operating conditions from arctic through to extreme desert environments. Broadband Propagation manufactures to customer specifications including diameter, length, frequency range and mounting connector.


Specifications

Frequency Range: To Order Impedance: 50 Ohms Radiation Pattern: Omni-Directional Polarisation: Vertical VSWR: Better than 3:1 Power Rating: 10 watts CW Input Connection: To Order Antenna Length: To Order Antenna Width: To Order Temperature Rating: -40 to +70 deg C Impact Rating: Over 1500 impacts to 90 Deg flexure without failure.



BP- VHF-RD – 0.5 PTR 349, VHF HANDHELD TRANSCEIVER ANTENNA Compressed Helical Type

The BP- VHF-RD 0.5 is a compressed helical (rubber ducky) type antenna covering the VHF Band of 36 to 58 MHz. This model is designed for use with the PTR 349 Handheld Transceiver.

The copper coated radiating element is covered in a protective poly-olefin shroud and is provided with a sturdy mounting base.

This is a rugged, tough, antenna designed for use in tactical combat in all types of operating conditions from arctic through to extreme desert environments.


Speci fications

Frequency Range: 36-58 MHz Impedance: 50 Ohms Radiation Pattern: Omni-Directional Polarisation: Vertical VSWR: Better than 3:1 Power Rating: 10 watts CW Input Connection: 50 Ohm suit PTR 349 Antenna Length: 0.5 metres Antenna Width: 14 mm at base, Antenna Weight: 120 grams Temperature Rating: -40 to +70 deg C Impact Rating: Over 1500 impacts to 90 Deg flexure without failure.



BP-VHF-2-STW BACKPACK TAPE WHIP ANTENNAS Broadband Propagation manufactures a range of light-weight, flexible, tape whip antennas for use with VHF man-pack transceivers. Standard length is one metre. Designed for use in tactical combat, in all types of operating conditions from arctic through to extreme desert environments they are constructed of highly durable, long-life, spring steel elements which will not break or lose their “set”. A flexible nylon braid covers the whip, increasing durability and providing high voltage contact protection. Antenna mounting connectors including thread, BNC, N, or C type can be provided or customer specified mountings can be supplied. The antenna is supplied with a goose neck base allowing for instant angle adjustment.

Fully Flexible

Customer Specified Mounting

Specifications

Frequency Range: 30-100 MHz Impedance: Nominal Radiation Pattern: Omni-Directional Polarisation: Vertical Power Rating: 10 watts CW Input Connection: Customer specified Antenna Length: 1.0 metres Antenna Width: 13 mm Antenna Weight: 130 grams Temperature Rating: -40 to +70 deg C . Integral Goose Neck




BP- VHF-TW 1 PTR 349, VHF HANDHELD TRANSCEIVER ANTENNA, Tape Whip Type

The BP- VHF-TW 1 is a light-weight, flexible, tape whip antenna covering the VHF Band of 36 to 58 MHz. designed for use with the PTR 349 Handheld Transceiver. At one metre in length it offers an increased range over the BP-VHF-RD 0.5 at the expense of increased operator conspicuousness. Designed for use in tactical combat, in all types of operating conditions from arctic through to extreme desert environments it is constructed of highly durable, long-life, spring steel elements which will not break or lose their “set”.

Specifications

Frequency Range: 36-58 MHz Impedance: 50 Ohms Radiation Pattern: Omni-Directional Polarisation: Vertical VSWR: Better than 3:1 Power Rating: 10 watts CW Input Connection: 50 Ohm suit PTR 349 Antenna Length: 1.0 metres Antenna Width: 13 mm Antenna Weight: 130 grams Temperature Rating: -40 to +70 deg C

. Integral Goose Neck




BP-LT-45-F BAND-1 LOG PERIODIC ANTENNA – Foldable

The BP-LT-45-F is a 16 element log periodic antenna covering the Radio Relay Band 1 frequency range of 225-450 MHz, with a mid-band gain of 13 dBi. Front to Back ratio is 28 dB Construction is of stainless steel, with stainless steel and Acetal fittings. The antenna folds at its centre to half its length to enable easy transport and storage.

Specifi cations Frequency Range: 225-450 MHz Gain: 10-13dBi Polarisation: Horizontal or vertical F/B Ratio: 28 dB Beam Width Vertical: 3 dB beamwidth in plane vertical to elements 76 deg. Beam Width Horizontal: 3 dB beamwidth in element plane 56 deg VSWR: 2:1 Power Rating 250 watts Input Connection: N type female Mounting: Mounts to 50mm shaft Antenna Length: 1.1 metres Antenna Width: 0.68 metres Antenna Weight: 2.8 kg


BROADBAND PROPAGATION Antenna Design & Supply Phone: (08) 8388 8132 1-3 Adelaide Rd. Echunga Fax: .(08) 8388 8536

PO Box 529 Echunga Intl.Phone: .(618) 8388 8132 South Australia. 5153 Intl.Fax: (618) 8388 8536 E-mail: [email protected] ABN: 84 232 273 647 Web: www.broadbandpropagation.com

BP25-13-18 BAND-3 CORNER REFLECTOR ANTENNA – Foldable

The BP25-13-18 is a high-gain corner reflector antenna for Radio Relay Band 3 (1350-1850 MHz). Side and back-lobes are highly attenuated. The antenna features low mass, low wind loading, rugged construction, and can be quickly folded flat for transport and storage. The antenna may be mounted horizontally for horizontal polarisation, or vertically for vertical polarisation. Construction is of aluminium, stainless steel and acetal, with stainless steel mounting fittings.

Specifications Electrical Frequency Range: 1350-1850 MHz Gain: > 16 dBi across operating band Polarisation: Horizontal or vertical F/B Ratio: E Plane >25 dB 0/90-270 deg. H Plane >25 dB 0/90-270 deg. 3dB (half power) Beam Width: E Plane 12-18 deg. H Plane 50-60 deg VSWR: < 2:1 Power Rating: 25 watts Input Connection: N type female Mechanical Mounting: Mounts to 50mm shaft/ boom Dimensions

Operating: 1010 x 320 x 370mm Folded: 1010 x 290 x 50mm

Antenna Weight: 5 kg Environmental Temperature: -40 deg C to 90 deg C Wind Speed Maximum: 40 m/s Wind Load: 360 N (at 30 m/s)



BP25-13-186 BAND-3 CORNER REFLECTOR ANTENNA - Foldable The BP25-13-186 is a high-gain corner reflector antenna for Radio Relay Band 3 (1350-1850 MHz). This is a six element version of our corner reflector with higher gain at 18 dBi. Side and back-lobes are highly attenuated. The antenna features low mass, low wind loading, rugged construction, and can be quickly folded flat for transport and storage. The antenna may be mounted horizontally for horizontal polarisation, or vertically for vertical polarisation. Construction is of aluminium, stainless steel and acetal, with stainless steel mounting fittings.

Specifications Electrical Frequency Range: 1350-1850 MHz Gain: > 18 dBi across operating band Polarisation: Horizontal or vertical F/B Ratio: E Plane >30 dB 0/90-270 deg. H Plane >30 dB 0/90-270 deg. 3dB (half power) Beam Width: E Plane 6-12 deg. H Plane 40-52 deg VSWR: < 2:1 Power Rating: 25 watts Input Connection: N type female Mechanical Mounting: Mounts to 50mm shaft/ boom Dimensions

Operating: 1105 x 290 x 455mm Folded: 1105 x 355 x 80mm

Antenna Weight: 5 kg Environmental Temperature: -40 deg C to 90 deg C Wind Speed Maximum: 40 m/s Wind Load: 360 N (at 30 m/s)


Free-Space, E Plane Radiation Pattern @ 1600 MHz

Free-Space, H Plane Radiation Pattern @ 1600 MHz



BPV-TM Tactical Mast Series The BPV-TM series of tactical, field deployable masts are of composite construction and feature strength and ruggedness combined with very low weight. The masts are push-up and can be extended and retracted quickly and easily. The clamping system is moulded from high strength polymer and allows for one handed operation. It exerts strong locking force on the mast sections and a clamp guard is incorporated to prevent accidental release

The 9.4m mast is constructed of glass composite, the 10m of glass/ carbon-fibre hybrid and the 45m mast is of carbon-fibre. It comes complete with guys, guying stakes, base plate and mallet in a canvas carry bag. Mounting kits for vehicles and shelters are available and can be tailored to meet customer needs. The mast series is suitable for light head-loads such as tactical HF wire antennas and VHF/ UHF omnidirectional antennas

Model No. 30-7 35-8 45-9 No. of Sections 7 8 9 Extended Height 9.4m (30ft) 10m (35ft) 14m (45ft) Retracted Height 1.8m 1.8m 2.1m Guying Radius 5.5m 6m 7.5m Mast Weight 3.4kg 3.35kg 4.7kg Accessories Weight 4kg 5kg 5kg Construction Glass

composite Glass/ carbon composite

Carbon composite

Pole Clamping System The mast head can be fitted with a variety of antenna mounting adaptors. Please specify the type of mount required when ordering


bpa tadiran

Documents

broadband antenna

vhf discone

hf broadband folded

folded dipole page

hf reference antenna

biconical dipole page

uhf base antennas uhf

broadband hf designs